PRODUCT SPECIFICATION DATE：03/26/2012 cosmo Photocoupler： ELECTRONICS CORPORATION KPC6N135H NO.62P51002 SHEET 1 OF 5 General Purpose Type Photocoupler z Features 1. Pb free and RoHS compliant. 2. High speed response tPHL, tPLH ( MAX. 1.5us at RL=4.1KΩ ) 3. High common mode rejection voltage ( CMH：TYP. 1KV/us ) 4. Standard dual-in-line package 5. Agency Approvals UL approved：UL1577 , No.E169586 CUL approved：C22.2 No.1 & NTC No.5 , No.E169586 VDE approved：EN60747 , No.40006080 FIMKO approved：EN 60065 No. FI 25798 EN 60950 No. FI 25798 z Application： 1. Computers, measuring instruments, control equipment. 2. High speed line receivers, high speed logic. 3. Telephone sets. 4. Signal transmission between circuits of different Potentials and impedances. REV. 2 PRODUCT SPECIFICATION DATE：03/26/2012 cosmo ELECTRONICS CORPORATION Photocoupler： NO.62P51002 KPC6N135H SHEET 2 OF 5 REV. 2 z Outside Dimension：Unit ( mm ) TOLERANCE：±0.2mm z Schematic：Top View 1. NC 2. Anode 3. Cathode 4. NC 5. GND 6. VO 7. VB 8. VCC PRODUCT SPECIFICATION DATE：03/26/2012 cosmo Photocoupler： ELECTRONICS CORPORATION z Absolute Maximum Ratings KPC6N135H NO.62P51002 SHEET 3 OF 5 REV. 2 ( Ta=25℃ ) Unit mA mA A V mW V V V mA mA mA mW Vrms ℃ ℃ ℃ Parameter Symbol Rating Forward current IF 25 *1 Peak forward current IF 50 Input *2 Peak transient forward current IFM 1 Reverse voltage VR 5 Power dissipation P 45 Supply voltage VCC -0.5 to 15 Output voltage VO -0.5 to 15 Emitter-base reverse with stand voltage ( Pin5 to 7 ) VEBO 5 Output Average output current IO 8 Peak output current IOP 16 Base current ( Pin7 ) IB 5 Power dissipation PO 100 *3 Isolation voltage 1 minute Viso 5000 Operating temperature Topr -55 to +100 Storage temperature Tstg -55 to +125 *4 Soldering temperature 10 second Tsol 260 *1 50% duty cycle, Pulse width：1mS Decreases at the rate of 1.6mA/℃ if the external temperature is 70℃ or more. *2 Pulse width≦1uS, 300pulse/sec *3 40 to 60% RH, AC for 1 minute *4 For 10 seconds z Electro-optical Characteristics ( Ta=0 to +70℃ unless otherwise specified ) Parameter Symbol Conditions MIN. TYP. MAX. Unit Ta=25℃, IF=16mA 7 40 % CTR(1) VO=0.4V, VCC=4.5V *5 Current transfer ratio IF=16mA 5 43 % CTR(2) VO=0.5V, VCC=4.5V Logic ( 0 ) output voltage VOL *6 VCC=4.5V, IF=16mA 0.1 0.4 V Ta=25℃, IF=0 3.0 500 nA IOH(1) VO=VCC=5.5V Logic ( 1 ) output current Ta=25℃, IF=0 IOH(2) 0.01 1.0 uA VO=VCC=15V IOH(3) VCC=VO=15V, IF=0 50 uA IF=16mA 200 uA Logic ( 0 ) supply current ICCL VO=open, VCC=15V Ta=25℃, IO=0 0.02 1.0 uA ICCH(1) VF=open, VCC=15V Logic ( 1 ) supply current IO=0 2.0 uA ICCH(2) VO=open, VCC=15V Ta=25℃, IF=16mA 1.7 1.95 V Input forward voltage VF mV/℃ Input forward voltage temperature coefficient △VF/△Ta IF=16mA -1.9 Ta=25℃, IR=10uA 5.0 V Input reverse voltage BVR Input capacitance CIN VF=0, f=1MHz 60 pF Ta=25℃, 45%RH 1.0 uA *7 Leak current ( input-output ) II-O VI-O=3KVDC, t=5s 12 Ω *7 Isolation resistance ( input-output ) RI-O VI-O=500VDC 10 *7 Capacitance ( input-output ) CI-O f=1MHz 0.6 pF Transistor current amplification factor hFE VO=5V, IO=3mA 70 *5 Current transfer ratio is the ratio of input current and output current expressed in % *6 IO=1.1mA *7 Measured as 2-pin element ( Short 1, 2, 3, 4 and 5, 6, 7, 8 ) PRODUCT SPECIFICATION DATE：03/26/2012 Photocoupler： cosmo KPC6N135H ELECTRONICS CORPORATION z NO.62P51002 SHEET 4 OF 5 ( Ta=25℃, VCC=5V, IF=16mA ) MIN. TYP. MAX. Unit Switching Characteristics Parameter Propagation delay time Output (1) Æ (0) *8 Propagation delay time *9 Output (0) Æ (1) Instantaneous common *10 *11 mode rejection voltage “ Output (1) “ Instantaneous common *10 *11 mode rejection voltage “ Output (0) “ Symbol *8 *9 *12 REV. 2 Conditions tPHL RL=4.1KΩ - 0.3 1.5 uS tPLH RL=4.1KΩ - 0.4 1.5 uS CMH IF=0, VCM=10VP-P - 1000 - V/uS CML IF=16mA, VCM=10VP-P - -1000 - V/Us BW RL=100Ω - 2.0 - MHz Bandwidth *8 RL=4.1KΩ is equivalent to one LSTTL and 6.1KΩ pull-up resistor. *10 Instantaneous common mode rejection voltage “ output (1) “ represents a common mode voltage variation that can hold the output above (1) level ( Vo > 2.0V ) Instantaneous common mode rejection voltage “ output (0) “ represents a common mode voltage variation that can hold the output above (0) level ( Vo < 0.8V ) *12 Bandwidth represents a point where AC input goes down by 3dB. *9 Test Circuit Propagation Delay Time IF Pulse input Duty ratio = 1/10 0 IF 1 8 2 7 3 6 Vcc 5V Vo RL Vo 1.5V 0.01uF IF monitor 1.5V C L =15pF 5 4 100Ω t PHL t PLH *11 Test Circuit for Instantaneous Common Mode Rejection Voltage 10V IF 1 8 2 7 3 6 B Vcc=5V 4 5 VFF VCM 0V RL Vo 0.01uF A 10% 90% CM H Vo 10% 90% tr tf 5V IF =0 2V V CM + - CM L Vo 0.8V IF =16mA VOL PRODUCT SPECIFICATION DATE：03/26/2012 cosmo ELECTRONICS CORPORATION Photocoupler： KPC6N135H NO.62P51002 SHEET 5 OF 5 z Notice The information contained in this document is intended to be a general product description and is subject to change without notice. Please contact cosmo in order to obtain the latest device data sheets before using any cosmo device. cosmo does not assume any responsibility for use of any circuitry described. No circuit patent licenses are implied. This publication is the property of cosmo. No part of this publication may be reproduced or copied in any form or by any means, or transferred to any third party without the prior written consent of cosmo Electronics Corporation. The devices listed in this document are designed for general applications only in electronic equipment. No devices shall be deployed which require higher level of reliability such as： – – – – Medical and other life support equipments. Space application. Telecommunication equipment ( trunk lines ). Nuclear power control equipment. Unless it received prior written approval from cosmo. cosmo takes no responsibility for damages arise form the improper usage of our device. Please contact cosmo for further information regarding the above notices. REV. 2