11-MD152 Version Issue Date Total Page : A.005 : 2004/08/29 : 14 Multi-Channels Motor Driver For DSC 新竹市展業一路 9 號 7 樓之 1 SILICON TOUCH TECHNOLOGY INC. 9-7F-1, Prosperity Rd I, Science-Based Industrial ParkHsinchu, Taiwan, R.O.C. Tel：886-3-5645656 Fax：886-3-5645626 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. 11-MD152 Multi-Channels Motor Driver For DSC General Specifications The 11-MD152 is all in one actuator driver for Digital Still Camera. It contains constant current control for M-shutter and constant voltage control for zoom DC motor. It has multiple channels, which can apply to DSC or DV zooming Lens. Features and Benefits Low voltage operation (VDD Min = VB Min = 2.7V) Low saturation voltage (Upper transistor + lower transistor residual voltage 0.25V typically at 200mA, VDD = VB = 3V) Low input current Constant current control and constant voltage control Zero standby current Reference Voltage inside (Vref=1.23V) Thermal shutdown protection Thin, highly reliable package :QFN-32(4.75mm X 4.75mm) and TSSOP-24 Pin Assignment PIM VDD GND OUT1 IM NC NC Pin Assignment of TSSOP-24 EN1 Pin Assignment of QFN-32 32 31 30 29 28 27 26 25 VDD OUT1 PIM GND EN1 IM EN2 1 24 GND EN3 2 23 OUT2 EN2 OUT2 IN1 3 22 OUT3 EN3 OUT3 IN2 4 21 OUT5 IN1 OUT5 IN3 5 20 OUT6 IN2 OUT6 IN4 6 19 OUT7 IN3 OUT7 VREF 7 18 OUT4 IN4 OUT4 NC OUT8 17 OUT8 VREF 8 NC GND VC VB SP-MD152-A.005.doc 16 NC 15 NC 14 NC 13 GND 12 VB 11 NC 10 NC VC 9 Version：A.005 Page：1 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Pin Descriptions of QFN-32 Pin NO. Pin Name Description Pin NO. Pin Name Description 1 EN2 Mode Selected Input pin 17 OUT8 Constant voltage Output pin 2 EN3 Mode Selected Input pin 18 OUT4 Constant voltage Output pin 3 IN1 Motor control input pin 19 OUT7 Motor output pin 4 IN2 Motor control input pin 20 OUT6 Motor output pin 5 IN3 Motor control input pin 21 OUT5 Motor output pin 6 IN4 Motor control input pin 22 OUT3 Motor output pin 7 VREF Reference voltage output pin 23 OUT2 Motor output pin 8 NC 24 GND Controller and driver ground 9 VC 25 NC 10 NC 26 NC 11 NC 27 IM 12 VB Power supply pin for motor driver 28 OUT1 Motor output pin 13 GND Motor driver ground 29 GND Controller and driver ground 14 NC 30 VDD Power supply pin for controller. 15 NC 31 PIM Current sense resistor 16 NC 32 EN1 Mode Selected Input pin Voltage adjust control Current sense resistor Pin Descriptions of TSSOP-24 Pin NO. Pin Name Description Pin NO. Pin Name Description 1 VDD Power supply pin for controller. 13 VB 2 PIM Current sense resistor 14 GND Driver ground 3 EN1 Mode selected Input pin 15 OUT8 Constant voltage output pin 4 EN2 Mode selected Input pin 16 OUT4 Constant voltage output pin 5 EN3 Mode selected Input pin 17 OUT7 Motor output pin 6 IN1 Motor control input pin 18 OUT6 Motor output pin 7 IN2 Motor control input pin 19 OUT5 Motor output pin 8 IN3 Motor control input pin 20 OUT3 Motor output pin 9 IN4 Motor control input pin 21 OUT2 Motor output pin 10 VREF Reference voltage output pin 22 IM 11 NC 23 GND Controller and driver ground 12 VC 24 OUT1 Motor output pin Voltage adjust control SP-MD152-A.005.doc Version：A.005 Power supply pin for motor driver Current sense resistor Page：2 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Absolute Maximum Ratings ( Unless otherwise noted, TA= 25℃ Characteristic ) Symbol Rating Unit VDD 5.5 V VB 7 V VIN VDD+0.4 V IO Peak Current IOPeak 1.5 A IODC Current IODC 550 mA Power Dissipation PD 800 mW Operating Temperature Range TOPR -40 ~ 125 °C Storage Temperature Range TSTG -65 ~ 150 °C Supply Voltage Input Voltage Electrical Characteristic (Unless otherwise noted, TA= 25℃ , VDD = VB = 3V ) Characteristic Sym. Supply Voltage Limit Condition Unit Min. Typ. Max. VDD 2.7 3 5.5 V VB 2.7 3 5.5 V 0.1 5 μA ISTB VEN1~ EN3 =L; VIN1~ IN4 =L Supply Current IDD1 VEN1~ EN3 = HHL 1 1.5 mA ( IDD ) IDD2 VEN1~ EN3 = HLL 1 1.5 mA IDD3 VEN1~ EN3 = LLH 1.2 2 mA Vref VDD = VB = 3V 1.19 1.23 1.27 V Reference Voltage Circuit Reference Voltage EN1~3 / IN1~4 Input Terminal ( TJ = 25℃) Input Voltage “H” VIH - 0.8*VDD - VDD+0.4 V Input Voltage “L” VIL - -0.4 - 0.2*VDD V Input Current “H” IIH VIN = VDD - - ±5 μA Input Current “L” IIL VIN = 0 V - - ±5 μA IOUT = 200 mA - 0.25 0.4 V IOUT = 200 mA - 0.25 0.4 V AF Output Terminal (OUT2-3，OUT6-7) Saturation Voltage (upper + lower) VSAT1 AE Output Terminal (OUT5-6) Saturation Voltage (upper + lower) VSAT2 SP-MD152-A.005.doc Version：A.005 Page：3 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. SH Output Terminal (OUT1-2) Ra + Rb = 10 kΩ Output Current1 IO1 OUT2-> OUT1 RIM = 1Ω 260 285 310 mA Output Current1 IO2 OUT1-> OUT2 RPIM = 0.9Ω 260 290 325 mA - 0.25 0.4 V 2.86 2.99 3.12 V - 0.22 0.36 V Saturation Voltage VSAT3 (upper + lower) IOUT = 200 mA ZOOM Output Terminal (OUT4-8) Output Voltage VOUT VB = 3 ~ 4V Vc=1V Saturation Voltage VSAT4 (upper + lower) IOUT = 200 mA Thermal Protection Circuit Protection Temperature TTSD VEN1 or VEN2 or VEN3 =H ℃ 160 Function Block CPU GND 23 EN1 VDD 1 EN2 3 EN3 4 VDD IN1 5 VDD IN2 6 IN3 7 VDD VDD IN4 8 VDD 9 VDD VDD 10uF BIAS VREF 10 Ra Logic THD VC 12 Rb VB 13 10uF RPIM 2 PIM IM 22 OUT1 24 14 OUT2 21 OUT3 20 OUT5 19 OUT6 18 OUT7 17 OUT4 16 OUT8 15 RIM Shutter Constant Current Drive SP-MD152-A.005.doc Aperture AF Saturation Voltage Drive Version：A.005 DC Zoom Constant Voltage Drive Page：4 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Truth Table INPUT OUPUT EN1 EN2 EN3 IN1 IN2 IN3 IN4 L L L L L H L L L H H L L H L H L L L L H H L H L H O1 O2 O3 O4 O5 O6 O7 O8 — — L H — — — H L — — — — — — — — — — — L H — — — — — — — — — — — H L — — — — L H — — H L — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — H L H — — — — — — — — — — — — — — — — L H H — — L L — — L H — — H L — — H H — — * * L L — — * * L H H L L — — * * H L — — * * H H — — L L — L H L — H L H — — H H H H L — L L — L H — H L — H H — — L L — — L H — — H L — — H H H L H — — L L — — L H — — H L — — H H Note: “*”: Don’t care; “—“: High Impedance L L H H L H L H SP-MD152-A.005.doc — — — — — H L — — L H — — L H H — — — — — — — — — H L — Version：A.005 — L H — — — — — — — — — — — — — — — — — — — — — — H L — — — — — — L H — — — — — — — — — — H L — — L H — — H L — Page：5 MODE STB SH (VCM) & AE (VCM) or AE (STM) AE (STM) or AE (VCM) ZOOM (DCM) AF (STM) ZOOM (STM) 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Application Circuit 1 AF: Saturation drive for 2 phase, 1-2 phase stepping motor M-shutter: Constant current drive for shutter voice coil motor Aperture: Saturation drive for aperture voice coil motor ZOOM: Constant voltage drive for DC motor (forward/reverse/brake/standby) VDD 11-MD152 10μ VDD OUT1 PIM GND 1Ω VB 10μ 1Ω EN1 EN1 M-shutter 0.1μ IM 0.1μ EN2 EN2 OUT2 0.1μ 0.1μ EN3 EN3 OUT3 IN1 IN1 OUT5 IN2 IN2 OUT6 IN3 IN3 OUT7 IN4 IN4 OUT4 VREF OUT8 NC GND VC VB AF Aperture 0.1μ 0.1μ Ra M ZOOM VB 10μ Rb SP-MD152-A.005.doc Version：A.005 Page：6 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Truth Table For Application Circuit 1 Constant current control for SH VCM INPUT EN1 L EN2 L OUPUT EN3 IN1 IN2 IN3 IN4 O1 O2 H L L H H L H L H L L L L L L L L — L H — — H L — Saturation control for AE VCM INPUT EN1 L EN2 H H EN2 L IN1 IN2 IN3 IN4 O5 O6 H L L L L L L L L L L H H L H L H — L H — — H L — L H EN2 H EN3 L Note: “*”: Don’t care; MODE IN1 IN2 IN3 IN4 O4 O8 * * L L — — * * L H L H * * H L H L * * H H H H IN1 IN2 IN3 ZOOM (DCM) OUPUT IN4 L H L L L H L H L L L H H L L H H L L L H L H L L L H L L H H L “—“: High Impedance SP-MD152-A.005.doc AE (VCM) OUPUT Saturation control for 1-2 phase AF STM INPUT EN1 MODE EN3 EN3 SH (VCM) OUPUT Constant voltage control for ZOOM DCM INPUT EN1 MODE MODE O2 O3 O6 O7 L L — H H H — L H H — L L L — H — L L L — H H H — H H H — L L L Version：A.005 AF (STM) Page：7 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Application Circuit 2 AF: Saturation drive for 2 phase, 1-2 phase stepping motor M-shutter: Constant current drive for shutter voice coil motor Aperture: Saturation voltage drive for stepping motor ZOOM: Constant voltage drive for DC motor (forward/reverse/brake/standby) VDD 11-MD152 10μ VDD OUT1 PIM GND EN1 EN1 IM EN2 EN2 OUT2 EN3 EN3 OUT3 IN1 IN1 OUT5 IN2 IN2 OUT6 IN3 IN3 OUT7 IN4 IN4 OUT4 VREF OUT8 NC GND VC VB 1Ω VB 10μ 1Ω Shutter 0.1μ 0.1μ 0.1μ 0.1μ AF 0.1μ 0.1μ Aperture M Ra 0.1μ ZOOM VB 10μ Rb SP-MD152-A.005.doc Version：A.005 Page：8 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Truth Table For Application Circuit 2 Constant current control for SH VCM INPUT EN1 L EN2 L OUPUT EN3 IN1 IN2 IN3 IN4 O1 O2 H L L H H L H L H L L L L L L L L — L H — — H L — Saturation voltage control for 2 phase AE STM INPUT EN1 L EN2 H H EN2 L H EN2 H MODE EN3 IN1 IN2 IN3 IN4 O3 O4 O5 O6 H L H H L H L L H L L H H H H L L L H H L H L L H L L H H H H L L EN3 L OUPUT EN3 IN2 IN3 IN4 O4 O8 * * L L — — * * L H L H * * H L H L * * H H H H L Note: “*”: Don’t care; IN1 IN2 IN3 L H L L L H L H L L L H H L L H H L L L H L H L L L H L L H H L “—“: High Impedance SP-MD152-A.005.doc ZOOM (DCM) OUPUT IN4 MODE O2 O3 O6 O7 L L — H H H — L H H — L L L — H — L L L — H H H — H H H — L L L Version：A.005 AE (STM) MODE IN1 Saturation control for 1-2 phase AF STM INPUT EN1 SH (VCM) OUPUT Constant voltage control for ZOOM DCM INPUT EN1 MODE AF (STM) Page：9 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Application Notes The 11-MD152 integrates saturation voltage, constant voltage, and constant current of motor driver. The range of supply voltage of 11-MD152, VDD and VB, is from 2.7V to 5.5V. The 11-MD152 input range is defined that logic “H” is from 0.8*VDD to VDD+0.4V and logic “L” is from –0.4V to 0.2*VDD. EN1, EN2 and EN3 are mode selection pins; IN1, IN2, IN3 and IN4 are motor rotation selection pins. Normally VB should provide enough current for output loading, thus large value of C is suggested for the terminal VB. Besides, 0.01uF~0.1uF of capacitors are also suggested between each output channel and output channel to ground. VC provides the reference of output level at OUT4 and OUT8. If 3*VC < VB, OUT4/OUT8 gets 3 times of VC at logic “H”. And if 3*VC > VB, OUT4/OUT8 is saturated at logic “H”. Constant current operation of 11-MD152 provides the current, which can be approximated by the following formula (See the depiction of application circuit 1. Ra+Rb is the resistance connected from Vref to ground): I PIM = I IM = (R PIM ( R IM 2900 + 0.1 )(Ra + Rb) 3150 + 0.1)(Ra + Rb) (unit : A) (unit : A) Before switching the mode of actuator, make sure to pull low the motor rotation selection pins. Then, switch to next mode to drive the motor. SP-MD152-A.005.doc Version：A.005 Page：10 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Package Specifications (QFN-32) TOP VIEW BOTTON VIEW D D2 L D1 32 25 25 1 24 32 1 24 e MD152 DDDDDDDD E E1 8 E2 17 17 8 L 9 16 16 9 e b Note: “DDDDDDDD” are the date Θ1 code or lot number and may be A2 A A3 A1 changed. Dimensions in Millimeter SYMBOL MIN NOM A 0.80 0.90 1.00 A1 0 0.02 0.05 A2 0 0.65 1.00 A3 b 0.18 0.203 REF 0.25 0.30 D 4.90 5.00 5.10 D1 4.75 BSC D2 3.10 3.20 3.30 E 4.90 5.00 5.10 E1 E2 L 3.10 0.45 4.75 BSC 3.20 0.6 Θ1 0° e SP-MD152-A.005.doc MAX 0.50 3.30 0.75 12˚ BSC Version：A.005 Page：11 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. Package Specifications (TSSOP-24) A 13 24 MD152 DDDDDDDD e b E 12 S D A A2 1 E1 A1 L L1 Note: “DDDDDDDD” are the date code or lot number and may be changed. Dimensions in Millimeter SYMBOL MIN NOM MAX 1.20 A － － A1 0.00 － 0.15 A2 0.80 1.00 1.05 B 0.19 － 0.30 e D E E1 L S 0.65 BASIC 7.70 4.30 0.45 0.20 L1 θ SP-MD152-A.005.doc 7.80 7.90 6.4 BASIC 4.40 0.60 4.50 0.75 － － 1.00REF 0° － Version：A.005 8° Page：12 Θ 點晶科技股份有限公司 11-MD152 SILICON TOUCH TECHNOLOGY INC. The products listed herein are designed for ordinary electronic applications, such as electrical appliances, audio-visual equipment, communications devices and so on. Hence, it is advisable that the devices should not be used in medical instruments, surgical implants, aerospace machinery, nuclear power control systems, disaster/crime-prevention equipment and the like. Misusing those products may directly or indirectly endanger human life, or cause injury and property loss. Silicon Touch Technology, Inc. will not take any responsibilities regarding the misusage of the products mentioned above. Anyone who purchases any products described herein with the above-mentioned intention or with such misused applications should accept full responsibility and indemnify. Silicon Touch Technology, Inc. and its distributors and all their officers and employees shall defend jointly and severally against any and all claims and litigation and all damages, cost and expenses associated with such intention and manipulation. SP-MD152-A.005.doc Version：A.005 Page：13