Data Sheet - Product finder

Automotive Chip Choke®
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes
Meets AEC-Q200 Requirements
Suppression of common mode noise without
attenuating the signal
Magnetically shielded versions for lower Rdc
and higher current
USB 3.0 and other high speed differential signal
lines (IEEE1394, LVDS)
Electrical Specifications @ 25°C - Operating Temperature -40°C to +125°C
Common Mode Impedance
(10MHZ)
Part Number
Min
Typ
Inductance
(uH)
Standard
Tolerance
RDC
(Ω Max)
IDC
(mA MAX)
PE-1812ACC110STS
300
600
11
+50/-30%
0.5
0.36
PE-1812ACC220STS
600
1200
22
+50/-30%
0.6
0.31
PE-1812ACC510STS
1500
3500
51
+50/-30%
1.0
0.23
PE-1812ACC101STS
3000
7500
100
+50/-30%
2.0
0.20
Weight ......................120 grams/reel
Tape & Reel ..................150/reel
Mechanical
Schematic
PE-1812ACCXXXSTS
3.0 max
3.2±0.2
4.5±0.2
3
1
4
3
3.8 ref
1
4
3.2
0.7 ref
5.9
USA 858 674 8100
Germany 49 7032 7806 0
1
Singapore 65 6287 8998
pulseelectronics.com
Shanghai 86 21 62787060
1.6
2
3.4
0.65 ref
2
China 86 755 33966678
Taiwan 886 3 4356768
W717.A (02/15)
All Units in mm
Automotive Chip Choke®
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes
Temp vs DC Current
Impedance vs Frequency
PE-1812ACC110STS
Differenal mode
Common mode
[email protected]
60.0
10,000
50.0
1,000
Differenal mode
100 10,000
30.0
50.0
20.0
10.0
0.0
10
0.1
1
10
100
Frequency(MHz)
1
0.1
10,000.0
1,000
Common mode
Differenal mode
1
10
100
Frequency(MHz)
1,000
Common mode
0.0
60.0
Differenal mode
0.4
0.2
IDC(A)
0.6
0.8
[email protected]
0.4
0.6
IDC(A)
1.0
0.8
1.0
[email protected]
40.0
ː T(℃)
10.0 1,000.0
60.0
30.0
50.0
20.0
40.0
ː T(℃)
1.0 100.0
10.0
10.0
0.0
10
100
Frequency(MHz)
1.0
0.2
50.0
100.010,000.0
Impedance( Ω)
0.020.0
0.0
1,000.0
1
30.0
10.0
PE-1812ACC220STS
0.1
40.0
ː T(℃ )
100
1
Impedance( Ω)
60.0
1,000
Impedance (Ω)
10
[email protected]
40.0
ː T(℃ )
Impedance (Ω)
Common mode
1,000
30.0
0.020.0
0.2
0.4
IDC(A)
10.0
0.6
0.8
0.0
0.1
1
10
100
Frequency(MHz)
2
1,000
pulseelectronics.com
0.0
0.2
0.4
IDC(A)
0.6
0.8
W717.A (02/15)
Automotive Chip Choke®
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes
Temp vs DC Current
Impedance vs Frequency
PE-1812ACC510STS
100,000.0
Common mode
Differenal mode
Common mode
[email protected]
70.0
Differenal mode
100,000.0
10,000.0
50.0
60.0
ː T(℃ː
) T(℃ )
Impedance(Ω)
Impedance(Ω)
10,000.0
100.0
100.0
10.0
40.0
50.0
30.0
40.0
20.0
30.0
10.0
20.0
0.0
10.0
10.0
1.0
1
10
1
10
1.0
PE-1812ACC101STS
100
1,000
100
1,000
Frequency(MHz)
Frequency(MHz)
Common mode
Common mode
0.0
0.1
0.2
0.3
0.4
IDC(A)
0.5
0.6
0.7
0.0
0.1
0.2
0.3
0.4
IDC(A)
0.5
0.6
0.7
0.0
Differenal mode
[email protected]
100,000.0
60.0
Differenal mode
[email protected]
100,000.0
10,000.0
60.0
50.0
50.0
40.0
10,000.0
1,000.0
ː T(℃ )ː T(℃ )
Impedance(Ω)
Impedance(Ω)
[email protected]
60.0
70.0
1,000.0
100.0
100.0
10.0
40.0
30.0
30.0
20.0
20.0
10.0
10.0
1.0
1
10
100
1,000
1
10
100
1,000
1.0
3
pulseelectronics.com
10.0
0.0
0.00
0.0
0.00
0.10
0.20
0.10
0.20
IDC(A)
IDC(A)
0.30
0.40
0.50
0.30
0.40
0.50
W717.A (02/15)
Automotive Chip Choke®
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes
Reliability Test
Item
Reference documents
1. High Temperature Exposure
MIL-STD-202 Method 108
Test Condition
Test Specification
1. Temperature: 125�C
2. Time: 96 hours
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
1. Temperature: 40�C~125�C
2. Number of cycles: 96 cycle
3.Dwell time: 30 minutes
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
2. Temperature Cycling
JESD22 Method JA-104
3. Biased Humidity Test
MIL-STD-202 Method 103
1. Temperature: 85±5�C
2. Time: 96 hours
3. Humidity: 85±5% RH
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
4. Operational Life
MIL-PRF-27
1. Temperature: 125�C
2. Time: 96 hours
3. Apply rated current
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
5. External Visual
MIL-STD-883 Method 2009
Inspect product construction, marking and
workmanship
Per product specification standard
6. Physical Dimensions
JESD22 Method JB-100
Verify physical dimensions to the applicable product Per product specification standard
detail specification
7. Resistance to solvents
MIL-STD-202 Method 215
8. Vibration Test
MIL-STD-202 Method 204
9. Resistance to Soldering Heat Test
MIL-STD-202 Method 210
1. Temperature: 250±5�C
2. Time: (temp.≥217�C) 60~150 Second
3. IR reflow times: 3 times
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
10. Rated Current
MIL-STD-202 Method 330
Apply rated current for 5 seconds.
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
11. Temperature Rise
MIL-PRF-27
Apply rated current for 10 minutes.
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
12. Over load
MIL-PRF-27
Apply twice as rated current for 5 minutes.
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
13. Solderability Test
J-STD-002
14. Electrical Characterization
User Spec.
15. Withstanding Voltage Test
MIL-STD-202 Method 201
Immerse into solvent for 3±0.5 minutes & brush 10 1. No body change in appearance
times for their cycles.
2. No marking blurred.
3. Inductance shall not change more than ±30%
1. Frequency and Amplified: 10-2000-10 Hz, 1.5mm
2. Direction: X, Y, Z
1. No mechanical and electrical damage
3. Test duration: 2 hours for each direction, 6 hours 2. Inductance shall not change more than ±30%
in total
1. Bakeing in pre-testing: 155±5�C / 16Hours±30min.
2. Peak temperature: 240±5�C
The terminal shall be at least 95% covered with fresh
3. Time: (temp.≥217�C) 60~150 Second
solder.
4. IR reflow times: 1 time
1. Operating temperature:-40�C~125�C
2. Room Temperature: 25�C
1. No mechanical and electrical damage
2. Inductance shall not change more than ±30%
1. DV: 500V
2. Time: 1 minute
1. During the test no breakdown.
2. The characteristic is normal after test.
16. Drop
JESD22-B111
Package & Drop down from 1m. In 1 angle 1 ridge
& 2 surfaces orientation
1. No case deformation or change in appearance.
2. Inductance shall not change more than ±30%
17. Terminal Strength Test
JIS-C-6429
1. Apply push force to samples mounted on PCB.
2. Force of 1.8 kg for 60±1 seconds.
After test, inductors shall be on mechanical damge.
4
pulseelectronics.com
W717.A (02/15)
Automotive Chip Choke®
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes
Tape and Reel Specifications
Reel Dimensions (mm)
Series
Parts per Reel
A
B
C
D
E
W
P1
1812 ACC
500
178
60
13
17
14
12
2
Tape Dimensions (mm)
P2
P3
8
4
H
T
4
0.35
Recommended Solder Heat Resistance Profile
III. Description:
a. Ferrite drum core construction
b. Magnetically shielded
c. Enameled copper wire: H class
d. Product weight: 0.15g (ref.)
e. Moisture sensitivity Level 1
f. Products comply with RoHS’ requirements
g. Halogen Free available
IV. General specification:
a. Storage temp: -40�Cto+125�C
b. Operating temp: -40�Cto+125�C
(Temp. rise included)
c. Resistance to solder heat: 250�C 10 secs.
For More Information
Pulse Worldwide
Headquarters
12220 World Trade Drive
San Diego, CA
92128
U.S.A.
Pulse Europe
Einsteinstrasse 1
D-71083 Herrenberg
Germany
Pulse China Headquarters
Pulse North China
Pulse South Asia
Pulse North Asia
B402, Shenzhen Academy of
Room 2704/2705
135 Joo Seng Road
3F, No. 198
Aerospace TechnolSuper Ocean Finance
#03-02
Zhongyuan Road
ogy Bldg.
Ctr.
PM Industrial Bldg.
Zhongli City
10th Kejinan Road
2067 Yan An Road
Singapore 368363
Taoyuan County 320
High-Tech Zone
West
Taiwan R. O. C.
Nanshan District
Shanghai 200336
Tel: 886 3 4356768
Shenzen, PR China
China
Tel: 65 6287 8998
Fax: 886 3 4356823 (Pulse)
Tel: 858 674 8100
Tel: 49 7032 78060
518057
Fax: 65 6287 8998
Fax: 886 3 4356820 (FRE)
Fax: 858 674 8262
Fax: 49 7032 7806 135
Tel: 86 755 33966678
Tel: 86 21 62787060
Fax: 86 755 33966700
Fax: 86 2162786973
Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be
trademarks or registered trademarks of their respective owners. © Copyright, 2015. Pulse Electronics, Inc. All rights reserved.
5
pulseelectronics.com
W717.A (02/15)