Specification of Electret Condenser Microphone [RoHS Compliance] Model No.: Date: EM4015-BC JUN 05 2013 APPROVER CHECKER DESIGN GUOFENG HU CHANG FU GANG XIA YING BO Customer Name: Customer Model No.: APPROVER CHECKER DESIGN Please kindly make approval of our samples, And return this form by fax or E-mail, Thanks for your kind attention and cooperation. SOBERTON, INC. 211 North First Street Minneapolis, MN. 55401 Tel：612-849-6205 / Fax：952-933-3120 www.soberton.com / mailto:[email protected] YF130604A Page 1 of 6 Type: Omni directional Back Electret Condenser Microphone Model Number: EM4015-BC 1. Electrical Characteristics No Parameter （Temperature =20±2℃ Symbol 1.1 1.2 1.3 Sensitivity Output impedance Current Consumption S Z out IDSS 1.4 Signal to Noise Ratio S/N 1.5 1.6 1.7 Decreasing Voltage Operating Voltage Maximum input S.P.L ΔS Humidity=65±5%） Condition Min. 0dB=1V/Pa，at 1kHz f=1kHz VCC =2.0V,RL=2.2KΩ at 1kHz S.P.L=1Pa (A-Weighted Curve) VCC=3.0V to2.0V -51 Limits Center Max. -48 -45 2.2 500 Unit dB KΩ µA 58 dB -3 10 115 1.0 dB V dB 2. Typical Frequency Response Curve Frequency Response Microphone Response Tolerance Window Frequency(Hz) Lower Limit(dB) Upper Limit(dB) 50 100 800 1000 1200 3000 5000 12000 -6 -3 -3 0 -3 -3 -3 -8 +3 +3 +3 0 +3 +8 +8 +8 3. Circuit Diagram RL=2.2KΩ VS =2.0V C1＝10PF C2＝33PF C=1µF YF130604A Page 2 of 6 4. Measurement Setup Drawing 5. Appearance And Dimension Unit： mm 6. Material And Structure 10 Capacitor 9 FET 8 PCB 1 7 Copper ring 1 6 Chamber 1 5 Electret Plate 1 4 Spacer 1 3 Diaphragm 1 2 Case Copper 1 Dustproof gauze Waterproof cloth 1 Name material QTY 1 No. 1 10+33pf Remark YF130604A Page 3 of 6 7. Temperature Conditions Storage Temperature Range Operation Temperature Range -40℃ ~ +85℃ Note: Store in electronic warehouse. -40℃ ~ +85℃ 8. Terminal Mechanical Strength Terminal should be no interference in operation after pulled the terminal with 1kg for 1 minute. 9. Reliability Test After each of following test, the sensitivity of the microphone should be within ±3dB of initial sensitivity after 3hours of conditioning at 20℃. 1. Vibration Test Frequency : 10Hz~55Hz Amplitude : 1.52mm Change of Frequency : 1 octave/min 2 hours in each of axes 2. High Temperature Test +85℃ for 240 hours. 3. Low Temperature Test -40℃ for 240 hours. 4. Humidity Test 90%～95%RH,+60℃ for 240 hours. 5. Thermal shocking test –40°C, 30 minutes ↔ +80°C, 30 minutes, repeated 32 cycles → room temperature, 3 hours. 6.Temperature Cycles -40℃ (2h) (0.5h) +20℃ (2h) +85℃ (0.1h) (2h) (0.5h) +20℃ (2h) -40℃ (0.5h) (2h) for 5 cycles. 7. Packing Drop Test Height：1.5m Procedure: 5 times from each of axes 8. Electrostatic discharge Tested to IEC61000-4-2 level 3： a) Contact discharge The microphone shall operate normally after 10 discharges to is 6KV DC and the discharge network is 150pF and 330Ω. b) Air discharge The microphone shall operate normally after 10 discharges to is 8KV DC and the discharge network is 150pF and 330Ω 10. Soldering Condition 1. We suggest using anti-static welding machine which can control soldering temperature automatically. 2. Soldering temperature should be controlled under 320℃ and soldering time for each terminal should be 1~2 sec.. 3. Microphone should be fixed on the metal block (heat sink), which has high radiation effects, and heat sink shall contact with MIC tightly. 4. Microphone may easily be destroyed by the static electricity and the countermeasure for eliminating the static electricity shall be executed (worktable and human body shall be ground connection) YF130604A Page 4 of 6 5 Heat Sink Shape of heat sink Shape of hole at fixed part 11. Code Explanation NAME EXPLANATION Omni-directional Microphone Back Electret D=4.0mm T=1.5mm Pcb version 3 Dash Sensitivity –48±3dB Test Condition 2.2KΩ／2.0V Dash Welding Point Style Mic. Capacitance:10+33PF Dash NO Rubber Dash No especial require YF130604A Page 5 of 6 Packing 12. Packing chart 1. MODEL NUMBER ： EM4015-BC 2. DIMENSION:(LENGTH*WIDTH *HEIGHT) 2.1 Anti-Static Bag: 80mm*80mm*2mm 2.2 SMALL PACKET 80mm*80 mm*10mm 2.3 MIDDLE BOX: 175mm*85mm*50mm 2.4 CARTON SIZE: 550mm*230mm*235mm 3. QUANTITY AND WEIGHT 3.1 100PCS/SMALL BOX 3.2 1000PCS/MID BOX 3.3 30000PCS/CARTON 3.4 1PC=0.1g 3.5 NET WEIGHT：3.0kg 3.6 GROSS WEIGHT：7.0kg X1 100PCS 4. LABEL STIPULATION 4.1 CONTENTS SHOULD BE SEEN CLEAR. 1000PCS X30 30000PCS YF130604A Page 6 of 6