Data Sheet - OPTEK Technology

Optical Emitter and Sensor Pair
OPB100Z, OPB100-EZ, OPB100-SZ
Features:
•
•
•
•
•
•
Infrared LED emitter
Silicon phototransistor sensor
Snap-in mounting
Variable sensing distance over 36” (91.4 cm)
Low profile package
24” (61.0 cm) wire leads
Description:
The OPB100Z series consists of an infrared LED (OPB100-EZ) and phototransistor (OPB100-SZ) in separate
plastic housings. The low cost, snap-in design requires no screws or other mounting hardware for ease of
installation.
The emitter and sensor are not apertured, which allows separation distances in excess of 36” (91.4 cm) without
concern for precise alignment. The front side clip allows mounting of the product to any 0.059” (1.50 mm) thick
material.
This product is designed for general switching and low-speed data communications applications.
Ordering Information
Applications:
•
•
•
•
•
Non-contact reflective object
Non-contact interruptive sensing
Assembly line automation
Machine automation
Machine safety
Part
Number
LED Peak
Wavelength
OPB100-EZ
880 nm
Sensor
Lead Length /
Spacing
24" / 26 AWG
Wire
OPB100-SZ
Transistor
OPB100Z
Contains both OPB100-EZ & OPB100-SZ
Emitter (LED)
Color/Pin
Phototransistor
Description
Red-1
Anode
Black-2
Cathode
White-3
Green-4
Collector
Emitter
Red
White
Black
Green
Ø0.190 [Ø4.83]
Symbolize Cover
26 AWG
UL Rated
0.335 [8.51]
RoHS
Hole Pattern
Ø0.150 [Ø3.81]
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue C
2/2013
Page 1 of 3
Optical Emitter and Sensor Pair
OPB100Z, OPB100-EZ, OPB100-SZ
Absolute Maximum Ratings (TA=25°C unless otherwise noted)
Storage Temperature Range
-40o C to +85o C
Operating Temperature Range(1)
-40o C to +80o C
Input LED (OP298 for additional information)
Forward DC Current
100 mA
Peak Forward Current (1 μs pulse width, 300 pps)
1A
Reverse DC Voltage
2V
Power Dissipation
(2)
142 mW
Output Phototransistor (OP598 for additional information)
Collector-Emitter Voltage
30 V
Emitter-Collector Voltage
5V
Collector DC Current
Power Dissipation
50 mA
(3)
250 mW
Electrical Characteristics (TA = 25°C unless otherwise noted — for reference only)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Input Diode (See OP298 for additional information — for reference only)
VF
Forward Voltage
-
-
1.7
V
IF = 20 mA
IR
Reverse Current
-
-
15
μA
VR= 10 V
Emission Angle at Half Power Points
-
25
-
Degree
6.5
-
-
IF = 100 mA
mW/cm2 Distance = 1.43” (3.63 cm)
Aperture = 0.25” (6.35 mm)
qHP
EE (APT)
Apertured Radiant Intensity
IF = 20 mA
Output Phototransistor (See OP598 for additional information — for reference only)
V(BR)CEO
Collector-Emitter Breakdown Voltage
30
-
-
V
IC = 1 mA, EE = 0mw/cm2 (no light)
V(BR)ECO
Emitter-Collector Breakdown Voltage
5
-
-
V
IC = 100 μA, EE = 0mw/cm2 (no light)
Collector Dark Current
-
-
100
nA
VCE = 10V, IF = 0, EE = 0 mw/cm2
(no light)
Collector-Emitter Saturation Voltage
-
-
0.4
V
IC = 400 μA, EE = 1.7 mw/cm2
On-State Collector Current
5
-
-
mA
ICEO
VCE(SAT)
IC(ON)
VCE = 5 V, EE = 1.7 mw/cm2
Notes:
1. Derate linearly 3.33 mW/°C above 25°C.
2. All parameters measured using pulse technique.
3. Derate linearly 1.43 mW/°C above 25°C.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue C
2/2013
Page 2 of 3
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Optical Emitter and Sensor Pair
OPB100Z, OPB100-EZ, OPB100-SZ
Output Current vs. Distance
100
IF=20 mA
Typical Output Current (mA)
IF=50 mA
10
1
0.1
0.01
1
2
3
4
5
6
7
8
9
10
11
12
Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue C
2/2013
Page 3 of 3