datasheet: pdf - OPTEK Technology

Hermetic Infrared Emitting Diode
OP130 Series
Features:
•
•
•
•
•
•
TO-46 hermetically sealed package
Focused and non-focused optical light pattern
Enhanced temperature range
Mechanically and spectrally matched to other OPTEK devices
Choice of power ranges
Choice of narrow or wide irradiance pattern
“W”
Description:
Each OP130 series device is a 935 nm gallium arsenide (GaAs) infrared LED mounted in a hermetically sealed TO
-46 package that provides an enhanced temperature range with a variety of power ranges The TO-46 housing
also offers high power dissipation and superior protection for hostile environments.
Each OP130 device has a narrow beam with an inclusive angle at half power points of 18°. Each OP130W series
device has a broad irradiance pattern of 50° at half power points, providing relatively even illumination over a large
area. These devices are designed to efficiently operate with OP800, OP593, OP598 and OP599 phototransistors
or the OP830 photodarlington.
Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data.
Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for
more information.
Applications:
•
•
•
•
•
•
Ordering Information
Non-contact reflective object sensor
Assembly line automation
Machine automation
Machine safety
End of travel sensor
Door sensor
RoHS
Part
LED Peak
Number Wavelength
OP130
OP131
OP132
OP133
OP130W
OP131W
OP132W
OP133W
935 nm
Output Power
(mW/cm2)
Min / Max
1.0 / NA
3.0 / NA
4.0 / NA
5.0 / NA
1.0 / NA
3.0 / NA
4.0 / NA
5.0 / NA
Lens Total Beam
Type
Angle
Dome
Lead
Length
(Min)
18°
0.50"
Flat
50°
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue B
10/2012
Page 1 of 4
Hermetic Infrared Emitting Diode
OP130 Series
OP130, OP131, OP132, OP133
Anode
Cathode
DIMENSIONS ARE IN:
[MILLIMETERS]
INCHES
OP130W, OP131W, OP132W, OP133W
Anode
Cathode
DIMENSIONS ARE IN:
[MILLIMETERS]
INCHES
Pin #
LED
1
Anode
2
Cathode
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue B
10/2012
Page 2 of 4
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Hermetic Infrared Emitting Diode
OP130 Series
Absolute Maximum Ratings (TA=25°C unless otherwise noted)
Storage Temperature Range
-65o C to +150o C
Operating Temperature Range
-65o C to +125o C
2.0 V
Reverse Voltage
Continuous Forward Current
100 mA
Peak Forward Current (2 us pulse width, 0.1% duty cycle)
10.0 A
Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron]
260° C(1)(2)
Power Dissipation
200 mW(3)
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
1.0
3.0
4.0
5.0
-
-
mW
IF = 100 mA(3 )
Input Diode
PO
Radiant Power Output
OP130, OP130W
OP131, OP131W
OP132, OP132W
OP133, OP133W
VF
Forward Voltage
-
-
1.75
V
IF = 100 mA (3)
IR
Reverse Current
-
-
100
µA
VR= 2.0 V
λP
Wavelength at Peak Emission
-
935
-
nm
IF = 10 mA
β
Spectral Bandwidth between Half Power
Points
-
50
-
nm
IF = 10 mA
Notes:
1. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
2. Derate linearly 2.0 mW/° C above 25° C.
3. Measurement made with 100 µs pulse measured at the trailing edge of the pulse with a duty cycle of 0.1% and an IF = 100 mA.
Electrical Characteristics (TA = 25°C unless otherwise noted — for reference only)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
Spectral Shift with Temperature
-
+0.30
-
nm/°C
Emission Angle at Half Power Points
OP130 series
OP130W series
-
18
50
-
Degree
tr
Output Rise Time
-
1000
-
ns
tf
Output Fall Time
-
500
-
ns
TEST CONDITIONS
Input Diode
∆λP /∆T
θHP
IF = Constant
I
F
= 100 mA
IF(PK)=100 mA, PW=10 µs, and
D.C.=10.0%
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue B
10/2012
Page 3 of 4
Hermetic Infrared Emitting Diode
OP130 Series
OP130 Series (including “W” devices)
Forward Voltage vs Forward Current vs
Temperature
Optical Power vs IF vs Temp
4.0
1.8
Normalized at 20 mA and 20o C
1.7
3.5
-65°C
-40°C
-20°C
+0°C
+20°C
+40°C
+60°C
+80°C
+100°C
+125°C
3.0
Normalized Optical Power
Typical Forward Voltage (V)
1.6
1.5
1.4
1.3
-65°C
-40°C
-20°C
+0°C
+20°C
+40°C
+60°C
+80°C
+100°C
+125°C
1.2
1.1
1.0
2.5
2.0
1.5
1.0
0.5
0.9
0.0
0
5
10
15
20
25
30
35
40
45
0
5
10
15
20
25
30
35
40
45
50
Forward Current IF (mA)
Forward Current (mA)
Distance vs Output Power vs Forward Current
9
Normalized at 0.6" and 50 mA
8
Forward Current
Normalized Output Power
7
10 mA
20 mA
30 mA
40 mA
50 mA
60 mA
80 mA
100 mA
6
5
4
3
2
1
0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue B
10/2012
Page 4 of 4
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com