Plastic Infrared Emitting Diode OP265FAA Series Features: • • • • • T-1 (3 mm) package style Narrow irradiance pattern Dome lens Higher power output than GaAs at equivalent drive currents 850 nm diode Description: Each device in the OP265FAA series is a high intensity gallium arsenide infrared emitting diode (GaAIAs) that is molded in an IR transmissive clear or amber-tinted epoxy package with a dome lens. Devices feature a narrow source irradiance pattern and a variety of electrical characteristics. The small T-1 package style makes these devices ideal for space-limited applications. These devices are mechanically and spectrally matched to other OPTEK products as follows: OP265 devices conform to the OP505 and OP535 series devices. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data. Applications: • Space-limited applications • Applications requiring coupling efficiency • Battery-operated or voltage-limited applications DIMENSIONS ARE IN: [MILLIMETERS] INCHES Ordering Information Part Number LED Peak Wavelength IF (mA) Typ / Max Total Beam Angle Lead Length 20 / 50 18° 0.50” 5.5 / NA OP265FAA OP265FAB Output Power (mW/ cm2) Min / Max 850 nm 7.5 / 12.5 OP265FAC 11.5 / 16.5 OP265FAD 15.5 / NA 1 2 Pin # LED 1 2 Cathode Anode CONTAINS POLYSULFONE To avoid stress cracking, we suggest using ND Industries’ Vibra-Tite for thread-locking. Vibra-Tite evaporates fast without causing structural failure in OPTEK'S molded plastics. RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue B 03/10 Page 1 of 3 Plastic Infrared Emitting Diode OP265FAA Series Absolute Maximum Ratings (TA=25°C unless otherwise noted) -40o C to +100o C Storage and Operating Temperature Range 2.0 V Reverse Voltage Continuous Forward Current 50 mA Peak Forward Current (1 µs pulse width, 300 pps) 3.0 A 260° C(1) Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 100 mW(2) Power Dissipation Notes: 1. RMA flux is recommended. Duration can be extended to 10 second maximum when flow soldering. A maximum of 20 grams force may be applied to the leads when soldering. 2. Derate linearly at 1.33 mW/° C above 25° C. 3. EE(APT) is a measurement of the average apertured radiant incidence upon a sensing area 0.081” (2.06 mm) in diameter, perpendicular to and centered on the mechanical axis of the lens and 0.590” (14.99 mm) from the measurement surface. EE(APT) is not necessarily uniform within the measured area. Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX Apertured Radiant Incidence OP265FAA OP265FAB OP265FAC OP265FAD 5.50 7.50 11.50 15.50 - 12.5 16.5 - UNITS TEST CONDITIONS Input Diode EE (APT) mW/cm 2 IF = 20 mA Aperture = 0.081” diameter Distance = 0.590” from seating surface to aperture surface VF Forward Voltage - - 1.80 V IF = 20 mA IR Reverse Current - 10 - µA VR= 10 V λP Wavelength at Peak Emission - 850 - nm IF = 10 mA Spectral Shift with Temperature - ±0.18 - nm/°C Emission Angle at Half Power Points - 18 - Degree IF = 20 mA tr Output Rise Time - 10 - ns tf Output Fall Time - 10 - ns ∆λP /∆T θHP IF = Constant IF(PK)=100 mA, PW=10 µs, D.C.=10.0% OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 03/10 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Plastic Infrared Emitting Diode OP265FAA Series OP265F (AA, AB, AC, AD) Forward Voltage vs Forward Current vs Temperature Optical Power vs IF vs Temperature 3.5 1.8 Normalized at 50 mA and 20° C 1.7 3.0 -60° C -40° C -20° C 0° C 20° C 40° C 60° C 80° C 100° C 120° C Normalized Optical Power Typical Forward Voltage (V) 1.6 1.5 1.4 1.3 -60° C -40° C -20° C 0° C 20° C 40° C 60° C 80° C 100° C 120°C 1.2 1.1 1.0 2.5 2.0 1.5 1.0 0.5 0.0 0.9 0 10 20 30 40 50 60 70 80 90 0 100 10 20 30 40 50 60 70 80 Forward Current (mA) Forward Current IF (mA) Distance vs Output Power vs Forward Current Relative Radiant Intensity vs. Angular Displacement 90 100 1.0 6 Normalized at 1" and 50 mA 0.9 5 0.8 10 mA 20 mA 30 mA 40 mA 50 mA 60 mA 70 mA 80 mA 90 mA 100 mA 4 3 2 Relative Radiant Intensity Normalized Output Power Forward Current 0.7 0.6 0.5 0.4 0.3 0.2 1 0.1 0.0 0 0.2 '' 0.4 '' 0.6 '' 0.8 '' 1.0 '' 1.2 '' 1.4 '' 1.6 '' 1.8 '' 2.0 '' Distance (inches) -20 -15 -10 -5 0 5 10 15 20 Angular Displacement (Degrees) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue B 03/10 Page 3 of 3