Project Number: Tracking Code: TC073--1549 Requested by: Brandon Harpenau Date: 1/18/2007 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-HD-WT Part description: SEM/TEM Test Start: 01/18/2008 Product Rev: 0 Lot #: 1 Tech: Rodney Riley, Eng: Troy Cook Troy Cook Qty to test: 50 Test Completed: 3/12/2008 Full DVT Report PART DESCRIPTION SEM-125-02-03.0-H-D-WT\ TEM-125-02-03.0-H-D-WT Page 1 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM\TEM CERTIFICATION All instruments and measuring equipment were calibrated to National Institute for Standards and Technology (NIST) traceable standards according to IS0 10012-l and ANSI/NCSL 2540-1, as applicable. All contents contained herein are the property of Samtec. No portion of this report, in part or in full shall be reproduced without prior written approval of Samtec. SCOPE To perform the following tests: Full DVT APPLICABLE DOCUMENTS Standards: EIA Publication 364 TEST SAMPLES AND PREPARATION 1) 2) 3) 4) 5) All materials were manufactured in accordance with the applicable product specification. All test samples were identified and encoded to maintain traceability throughout the test sequences. After soldering, the parts to be used for LLCR and DWV/IR testing were cleaned according to TLWI-0001. Either an automated cleaning procedure or an ultrasonic cleaning procedure may be used. The automated procedure is used with aqueous compatible soldering materials. 6) 7) 8) 9) Parts not intended for testing LLCR and DWV/IR are visually inspected and cleaned if necessary. Any additional preparation will be noted in the individual test sequences. Solder Information: Lead Free Re-Flow Time/Temp: See accompanying profile. 10) Samtec Test PCBs used: PCB-100970-TST-XX Page 2 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM TYPICAL OVEN PROFILE (Soldering Parts to Test Boards) Page 3 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM FLOWCHARTS Mating/Unmating/Normal Force TEST STEP 01 02 03 04 05 06 07 08 09 10 11 12 13 14 GROUP A GROUP A GROUP A 10 Boards 10 Boards 10 Boards 100 Cycles 100 Cycles 100 Cycles GROUP B1 GROUP B2 Individual Contacts (30) min Individual Contacts (30) min Contact Meas. Contact Meas. Contact Meas. Setup Approve Setup Approve Mating / Unmating Data Review Mating / Unmating Data Review Mating / Unmating Data Review Normal Force Data Review Thermal Aging (Mated) Contact Gaps (Inscribed Circ.) 100 Cycles Cycles Cycles Mating / Unmating Mating / Unmating Mating / Unmating Contact Meas. Contact Meas. Contact Meas. Data Review Data Review Data Review Thermal Aging (Mated) Thermal Aging (Mated) Thermal Aging (Mated) Mating / Unmating Mating / Unmating Mating / Unmating Contact Meas. Contact Meas. Contact Meas. Data Review Data Review Data Review Humidity (Mated) Humidity (Mated) Humidity (Mated) Mating / Unmating Contact Meas. Mating / Unmating Contact Meas. Mating / Unmating Contact Meas. Thermal Aging = EIA-364-17, Test Condition 4, 105 deg C; Time Condition 'B' (250 hours) Humidity =EIA-364-31, Test Condition 'B' (240 Hours) and Method III (+25 ° C to +65 ° C @ 90%RH to 98% RH) ambient pre-condition and delete steps 7a and 7b Mating/Un-Mating Forces = EIA-364-13 Normal Force = EIA-364-04 Contact Gaps/Height - No standard method. Usually measured optically Page 4 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM Durability/Thermal Age/Cyclic Humidity TEST STEP GROUP A 200 Points 100 Cycles 01 02 03 04 05 06 07 08 09 10 LLCR-1 Data Review 100 Cycles LLCR-2 Data Review Thermal Age LLCR-3 Data Review Cyclic Humidity LLCR-4 Thermal Aging = EIA-364-17, Test Condition 4, 105 deg C; Time Condition 'B' (250 hours) Humidity =EIA-364-31, Test Condition 'B' (240 Hours) and Method III (+25° C to +65° C @ 90%RH/98% RH) ambient pre-condition and delete steps 7a and 7b LLCR = EIA-364-23, LLCR use Keithley 580 in the dry circuit mode, 10 mA Max IR / DWV TEST STEP 01 GROUP A GROUP B1 GROUP B2 2 Boards 2 Boards 2 Boards 2 Boards Ambient Ambient DWV/Working Voltage Thermal Humidity IR 02 03 04 05 06 07 Data Review GROUP B3 Thermal Aging Humidity DWV/Working Voltage DWV/Working Voltage Thermal Aging IR Data Review Humidity IR Thermal Aging = EIA-364-17, Test Condition 4, 105 deg C; Time Condition 'B' (250 hours) Humidity =EIA-364-31, Test Condition 'B' (240 Hours) and Method III (+25 ° C to +65 ° C @ 90%RH to 98% RH) ambient pre-condition and delete steps 7a and 7b IR = EIA-364-21 DWV = EIA-364-20 Page 5 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM Gas Tight TEST STEP 200 Points (min) 01 02 03 Gas Tight LLCR-2 GROUP A LLCR-1 Gas Tight = EIA-364-36 LLCR = EIA-364-23, LLCR use Keithley 580 in the dry circuit mode, 10 mA Max Page 6 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM ATTRIBUTE DEFINITIONS The following is a brief, simplified description of attributes. THERMAL: 1) 2) 3) 4) 5) EIA-364-17, Temperature Life with or without Electrical Load Test Procedure for Electrical Connectors. Test Condition 4 at 105° C. Test Time Condition B for 250 hours. All test samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. HUMIDITY: 1) 2) 3) 4) 5) Reference document: EIA-364-31, Humidity Test Procedure for Electrical Connectors. Test Condition B, 240 Hours. Method III, +25° C to + 65° C, 90% to 98% Relative Humidity excluding sub-cycles 7a and 7b. All samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. CONTACT GAPS: 1) Gaps above the surrounding plastic surface were measured before and after stressing the contacts (e.g. thermal aging, mechanical cycling, etc.). 2) Typically, all contacts on the connector are measured. MATING/UNMATING: 1) Reference document: EIA-364-13, Mating and Unmating Forces Test Procedure for Electrical Connectors. 2) The full insertion position was to within 0.003” to 0.004” of the plug bottoming out in the receptacle to prevent damage to the system under test. 3) One of the mating parts is secured to a floating X-Y table to prevent damage during cycling. INSULATION RESISTANCE (IR): To determine the resistance of insulation materials to leakage of current through or on the surface of these materials when a DC potential is applied. 1) PROCEDURE: a. Reference document: EIA-364-21, Insulation Resistance Test Procedure for Electrical Connectors. b. Test Conditions: i. Between Adjacent Contacts ii. Electrification Time 2.0 minutes iii. Test Voltage (500 VDC) corresponds to calibration settings for measuring resistances. 2) MEASUREMENTS: 3) When the specified test voltage is applied (VDC), the insulation resistance shall not be less than 5000 megohms. Page 7 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DIELECTRIC WITHSTANDING VOLTAGE (DWV): To determine if the sockets can operate at its rated voltage and withstand momentary over potentials due to switching, surges, and other similar phenomenon. Separate samples are used to evaluate the effect of environmental stresses so not to influence the readings from arcing that occurs during the measurement process. 1) PROCEDURE: a. Reference document: EIA-364-20, Withstanding Voltage Test Procedure for Electrical Connectors. b. Test Conditions: i. Between Adjacent Contacts ii. Rate of Application 500 V/Sec iii. Test Voltage (VAC) until breakdown occurs 2) MEASUREMENTS/CALCULATIONS a. The breakdown voltage shall be measured and recorded. b. The dielectric withstanding voltage shall be recorded as 75% of the minimum breakdown voltage. c. The working voltage shall be recorded as one-third (1/3) of the dielectric withstanding voltage (onefourth of the breakdown voltage). NORMAL FORCE (FOR CONTACTS TESTED OUTSIDE THE HOUSING): 1) Reference document: EIA-364-04, Normal Force Test Procedure for Electrical Connectors. 2) The contacts shall be tested in the loose state, not inserted in connector housing. 3) The contacts shall be prepared to allow access to the spring member at the same attitude and deflection level as would occur in actual use. 4) In the event that portions of the contact prevent insertion of the test probe and/or deflection of the spring member under evaluation, said material shall be removed leaving the appropriate contact surfaces exposed. 5) In the case of multi-tine contacts, each tine shall be tested independently on separate samples as required. 6) The connector housing shall be simulated, if required, in order to provide an accurate representation of the actual contact system performance. 7) A holding fixture shall be fashioned to allow the contact to be properly deflected. 8) Said holding fixture shall be mounted on a floating, adjustable, X-Y table on the base of the Dillon TC2, computer controlled test stand with a deflection measurement system accuracy of 5 µm (0.0002”). 9) The probe shall be attached to a Dillon P/N 49761-0105, 5 N (1.1 Lb) load cell providing an accuracy of ± 0.2%. 10) The nominal deflection rate shall be 5 mm (0.2”)/minute. 11) Unless otherwise noted a minimum of five contacts shall be tested. 12) The force/deflection characteristic to load and unload each contact shall be repeated five times. 13) The system shall utilize the TC2 software in order to acquire and record the test data. 14) The permanent set of each contact shall be measured within the TC2 software. 15) The acquired data shall be graphed with the deflection data on the X-axis and the force data on the Y-axis and a print out will be stored with the Tracking Code paperwork. Page 8 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM LLCR: 1) EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. 2) A computer program, LLCR 221.exe, ensures repeatability for data acquisition. 3) The following guidelines are used to categorize the changes in LLCR as a result from stressing a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms: ------------------ Unstable f. >+2000 mOhms:---------------------------- Open Failure GAS TIGHT: 1) 2) 3) 4) To provide method for evaluating the ability of the contacting surfaces in preventing penetration of harsh vapors which might lead to oxide formation that may degrade the electrical performance of the contact system. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms: ------------------ Unstable f. >+2000 mOhms:---------------------------- Open Failure Procedure: a. Reference document: EIA-364-36, Test Procedure for Determination of Gas-Tight Characteristics for Electrical Connectors, Sockets and/or Contact Systems. b. Test Conditions: i. Class II--- Mated pairs of contacts assembled to their plastic housings. ii. Reagent grade Nitric Acid shall be used of sufficient volume to saturate the test chamber iii. The ratio of the volume of the test chamber to the surface area of the acid shall be 10:1. iv. The chamber shall be saturated with the vapor for at least 15 minutes before samples are added. v. Exposure time, 55 to 65 minutes. vi. The samples shall be no closer to the chamber walls than 1 inches and no closer to the surface of the acid than 3 inches. vii. The samples shall be dried after exposure for a minimum of 1 hour. о viii. Drying temperature 50 C ix. The final LLCR shall be conducted within 1 hour after drying. Page 9 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM RESULTS Normal Force at Nominal Deflection (.006” deflection) • Initial o Min-------------------------------------------------35.93 gm o Max ------------------------------------------------48.57 gm • Thermal o Min-------------------------------------------------50.20 gm o Max ------------------------------------------------70.45 gm Mating – Unmating Forces (25 Position) • Initial o Mating Min --------------------------------------- 3.8 lbs Max--------------------------------------- 5.0 lbs o Unmating Min --------------------------------------- 3.4 lbs Max--------------------------------------- 4.5 lbs • After 100 Cycles o Mating Min --------------------------------------- 4.4 lbs Max--------------------------------------- 6.0 lbs o Unmating Min --------------------------------------- 4.4 lbs Max--------------------------------------- 5.9 lbs • Thermal o Mating Min --------------------------------------- 2.2 lbs Max--------------------------------------- 2.9 lbs o Unmating Min --------------------------------------- 2.0 lbs Max--------------------------------------- 2.8 lbs • Humidity o Mating Min --------------------------------------- 2.2 lbs Max--------------------------------------- 2.9 lbs o Unmating Min --------------------------------------- 2.2 lbs Max--------------------------------------- 2.9 lbs Page 10 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM Mating – Unmating Forces (50 Position) • Initial o Mating Min --------------------------------------- 8.7 lbs Max--------------------------------------10.7 lbs o Unmating Min --------------------------------------- 6.9 lbs Max--------------------------------------- 9.4 lbs • After 100 Cycles o Mating Min --------------------------------------- 9.0 lbs Max--------------------------------------13.2 lbs o Unmating Min --------------------------------------- 7.5 lbs Max--------------------------------------12.5 lbs • Thermal o Mating Min --------------------------------------- 4.6 lbs Max--------------------------------------- 6.2 lbs o Unmating Min --------------------------------------- 4.2 lbs Max--------------------------------------- 6.5 lbs • Humidity o Mating Min --------------------------------------- 3.7 lbs Max--------------------------------------- 4.9 lbs o Unmating Min --------------------------------------- 3.8 lbs Max--------------------------------------- 4.8 lbs Insulation Resistance minimums, Pin to Pin • Initial o Mated----------------------------------------------100,000 Meg Ω ------------------------ Pass o Unmated ------------------------------------------- 50,000 Meg Ω • Thermal o Mated----------------------------------------------100,000 Meg Ω o Unmated ------------------------------------------- 75,000 Meg Ω • Humidity o Mated----------------------------------------------100,000 Meg Ω o Unmated ------------------------------------------100,000 Meg Ω Page 11 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM Dielectric Withstanding Voltage minimums, DWV • Initial o Breakdown Mated ----------------------------------------950 VAC o DWV Mated ----------------------------------------712.5 VAC o Working voltage Mated ----------------------------------------237.5 VAC • Thermal o Breakdown Mated -------------------------------------- 1180 VAC Unmated----------------------------------- 1100 VAC o DWV Mated ----------------------------------------885 VAC Unmated-------------------------------------825 VAC o Working voltage Mated ----------------------------------------295 VAC Unmated-------------------------------------275 VAC • Humidity o Breakdown Mated -------------------------------------- 1020 VAC Unmated-------------------------------------980 VAC o DWV Mated ----------------------------------------765 VAC Unmated-------------------------------------735 VAC o Working voltage Mated ----------------------------------------255 VAC Unmated-------------------------------------245 VAC LLCR Durability (200 LLCR test points) • Initial --------------------------------------------------------------- 12.0 mOhms Max • Durability, 100 Cycles o <= +5.0 mOhms ----------------------------------- 200 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure • Thermal o <= +5.0 mOhms ----------------------------------- 200 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure o • Humidity o <= +5.0 mOhms ----------------------------------- 200 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Page 12 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM LLCR Gas Tight (185 LLCR test points) • Initial --------------------------------------------------------------- 15.5 mOhms Max • Gas-Tight o <= +5.0 mOhms ----------------------------------- 185 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure NOTE: Samples 4-8 have only 22 data points due to the orientation on the mating connector being reversed. Page 13 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DATA SUMMARIES MATING/UNMATING: 25 POSITION Initial Mating Minimum Maximum Average After 100 Cycles Mating Unmating Unmating Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) 60.5 79.2 69.5 3.78 5.0 4.3 54.6 71.9 62.3 3.41 4.5 3.9 70.6 96.5 80.5 4.42 6.0 5.0 70.3 94.9 78.9 4.39 5.9 4.9 After Thermals Mating Unmating Minimum Maximum Average After Humidity Mating Unmating Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) 34.9 46.2 39.9 2.18 2.9 2.5 32.0 44.1 37.1 2.00 2.8 2.3 35.7 45.6 39.9 2.23 2.9 2.5 35.0 46.9 40.6 2.19 2.9 2.5 50 POSITION Initial Mating Minimum Maximum Average After 100 Cycles Mating Unmating Unmating Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) 139.2 171.7 156.9 8.70 10.7 9.8 109.7 150.7 132.3 6.86 9.4 8.3 143.1 211.1 187.1 8.95 13.2 11.7 119.4 199.8 172.6 7.47 12.5 10.8 After Thermals Mating Unmating Minimum Maximum Average Mating After Humidity Unmating Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) 74.3 98.7 89.2 4.64 6.2 5.6 66.7 103.7 81.6 4.17 6.5 5.1 59.0 77.6 66.0 3.69 4.9 4.1 60.3 77.3 66.9 3.77 4.8 4.2 Page 14 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DATA SUMMARIES Continued NORMAL FORCE (FOR CONTACTS TESTED OUTSIDE THE HOUSING): 1) Calibrated force gauges are used along with computer controlled positioning equipment. 2) Typically, 8-10 readings are taken and the averages reported. Initial Averages Min Max St. Dev Count 0.001 5.91 4.92 7.57 0.92 7 Deflections in inches Forces in Grams 0.002 0.004 0.006 0.008 16.85 27.40 41.16 53.81 14.90 24.32 35.93 45.97 20.99 32.58 48.57 62.85 2.30 3.25 4.64 5.45 7 7 7 7 SET 0.0014 0.0010 0.0016 0.0002 7 0.001 7.12 6.30 9.10 0.93 7 Deflections in inches Forces in Grams 0.002 0.004 0.006 0.008 21.91 38.91 60.91 78.12 18.70 32.10 50.20 64.90 29.50 48.01 70.45 89.12 3.88 6.18 7.98 8.42 7 7 7 7 SET 0.0014 0.0012 0.0016 0.0002 7 Thermal Averages Min Max St. Dev Count Page 15 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DATA SUMMARIES Continued INSULATION RESISTANCE (IR): Initial minimum maximum average Pin-Pin Mated Unmated SEM/TEM SEM 100000 50000 100000 100000 100000 87500 Humidity minimum maximum average Thermal minimum maximum average Pin-Pin Mated Unmated SEM/TEM SEM 100000 75000 100000 100000 100000 93750 Pin-Pin Mated Unmated SEM/TEM SEM 100000 100000 100000 100000 100000 100000 DIELECTRIC WITHSTANDING VOLTAGE (DWV): Initial Minimum: Breakdown Voltage DWV Working Voltage Pin-Pin Mated SEM/TEM 950 712.5 237.5 Thermal Minimum: Breakdown Voltage DWV Working Voltage Humidity Minimum: Breakdown Voltage DWV Working Voltage Page 16 of 32 Pin-Pin Mated Unmated SEM/TEM SEM 1020 980 765 735 255 245 Pin-Pin Mated Unmated SEM/TEM SEM 1180 1100 885 825 295 275 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DATA SUMMARIES Continued LLCR: 1) 2) 3) 4) A total of 200 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms ------------------- Unstable f. >+2000 mOhms:---------------------------- Open Failure mOhm values Average St. Dev. Min Max Count Actual Initial 9.5 0.7 8.3 12.0 200 Delta 100 Cycles 0.2 0.9 -2.5 2.8 200 Page 17 of 32 Delta Thermal -0.5 1.0 -3.4 1.7 200 Delta Humidity -0.3 0.7 -3.5 1.6 200 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DATA SUMMARIES Continued GAS TIGHT: 1) 2) 3) 4) A total of 185 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms: ------------------ Unstable f. >+2000 mOhms:---------------------------- Open Failure mOhm values Average St. Dev. Min Max Count Actual Initial 10.1 1.2 8.5 15.5 185 Delta Gas Tight -0.5 0.7 -3.5 1.6 185 Page 18 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DATA NORMAL FORCE (FOR CONTACTS TESTED OUTSIDE THE HOUSING): Initial Sample # 1 2 3 4 5 6 7 0.001 5.33 6.12 4.92 6.59 5.49 5.33 7.57 Deflections in inches Forces in Grams 0.002 0.004 0.006 0.008 15.06 24.32 35.93 45.97 16.63 26.04 37.97 50.05 15.38 26.99 41.53 53.66 18.98 31.38 46.29 58.21 16.00 25.26 39.07 52.72 14.90 25.26 38.75 53.19 20.99 32.58 48.57 62.85 SET 0.00130 0.00150 0.00100 0.00150 0.00140 0.00160 0.00130 Thermal Sample # 1 2 3 4 5 6 7 0.001 7.06 6.40 6.90 9.10 7.10 6.30 7.00 Deflections in inches Forces in Grams 0.002 0.004 0.006 0.008 23.69 42.36 65.58 82.84 18.70 34.00 53.90 72.70 22.91 44.40 70.45 89.12 29.50 48.01 69.51 84.26 20.20 38.40 61.40 80.70 18.70 33.10 55.30 72.30 19.70 32.10 50.20 64.90 SET 0.00160 0.00130 0.00160 0.00120 0.00140 0.00150 0.00120 MATING/UNMATING: 25 Position After 100 Cycles After Thermals After Humidity Sample# 1 2 3 4 5 Mating Initial Unmating Mating Unmating Mating Unmating Mating Unmating 4.93 3.78 4.08 4.34 4.30 4.49 3.47 3.62 3.65 4.19 6.03 4.73 4.66 4.74 5.47 5.93 4.44 4.60 4.77 5.20 2.42 2.36 2.49 2.18 2.35 2.41 2.21 2.22 2.17 2.00 2.71 2.50 2.33 2.37 2.23 2.93 2.60 2.37 2.39 2.35 6 7 8 9 10 4.95 4.22 4.16 4.49 4.17 4.14 3.41 3.54 4.40 4.03 5.56 4.60 5.17 5.49 4.42 5.24 4.39 4.89 4.97 5.44 2.52 2.50 2.49 2.89 2.73 2.33 2.28 2.13 2.76 2.69 2.79 2.30 2.43 2.85 2.43 2.80 2.19 2.42 2.83 2.47 Page 19 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM After 100 Cycles After Thermals After Humidity Sample# 1 2 3 4 5 Mating Initial Unmating Mating Unmating Mating Unmating Mating Unmating 10.34 8.70 9.72 10.14 9.90 8.60 7.39 9.20 9.42 6.86 13.19 8.95 12.49 12.14 10.66 12.10 7.47 11.74 11.07 10.25 6.13 5.63 5.21 5.98 5.40 5.67 4.89 4.78 5.51 4.47 4.85 4.23 3.77 4.83 4.20 3.79 3.69 3.77 6 7 8 9 10 10.73 9.85 9.96 9.09 9.64 9.38 8.47 7.66 7.81 7.88 13.19 12.22 11.64 10.76 11.70 12.49 11.31 10.77 9.86 10.86 6.17 5.22 5.56 5.84 4.64 6.48 4.75 5.05 5.25 4.17 3.82 4.06 4.70 3.88 3.91 4.39 4.78 3.77 INSULATION RESISTANCE (IR): Initial Tested?: Sample# 1 2 3 4 Pin-Pin Mated Unmated x x SEM/TEM SEM 100000 100000 100000 50000 100000 100000 100000 100000 Humidity Tested?: Sample# 1 2 3 4 Thermal Tested?: Sample# 1 2 3 4 Pin-Pin Mated Unmated x x SEM/TEM SEM 100000 100000 100000 100000 100000 100000 100000 100000 Page 20 of 32 Pin-Pin Mated Unmated x x SEM/TEM SEM 100000 100000 100000 100000 100000 100000 100000 75000 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DATA Continued DIELECTRIC WITHSTANDING VOLTAGE (DWV): Initial Tested?: Sample# 1 2 3 4 Pin-Pin Mated x SEM/TEM 950 1100 1250 1200 Pin-Pin Mated Unmated Tested?: x x Sample# SEM/TEM SEM 1 1180 1150 2 1180 1100 Thermal Pin-Pin Mated Unmated Tested?: x x Sample# SEM/TEM SEM 1 1160 1130 2 1020 980 Humidity LLCR: Board 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 mOhm values Position P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 Actual Initial 8.7 8.9 8.5 8.9 9.1 9.2 8.4 9.0 8.6 8.7 8.9 8.9 9.2 9.3 9.2 9.0 9.2 9.5 9.5 9.8 9.4 Delta 100 Cycles 0.8 0.3 1.1 0.8 0.5 0.3 0.6 0.7 0.4 0.3 0.2 0.5 0.3 0.3 0.6 0.7 1.5 1.2 0.3 0.5 0.5 Delta Thermal 0.9 1.2 1.7 1.3 0.7 0.6 0.9 0.4 0.9 0.8 0.5 0.0 -0.6 -0.8 -0.5 -0.6 -0.3 -1.1 -0.7 -0.8 -0.8 Page 21 of 32 Delta Humidity 1.2 -0.4 0.1 0.0 -0.5 -0.6 -0.1 -0.4 -0.3 -0.4 -0.6 -0.6 -0.7 -0.1 0.0 0.4 0.4 0.0 0.0 0.2 0.3 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 9.8 9.7 9.7 9.1 8.5 8.9 9.4 9.0 8.7 8.9 8.5 8.7 8.9 9.0 9.8 9.4 10.6 10.5 10.4 9.3 9.6 12.0 8.6 9.9 9.7 9.7 9.7 9.3 9.6 8.3 8.9 9.2 9.8 8.7 9.0 8.7 8.9 8.9 9.0 8.9 8.8 9.4 9.8 9.3 9.6 9.3 9.8 9.8 10.5 0.6 0.8 0.8 0.6 0.3 0.5 0.0 0.3 0.7 0.4 0.3 0.3 0.4 0.3 -0.9 -0.5 -1.4 -0.5 -0.5 0.9 0.1 -2.5 0.2 0.7 0.1 0.0 0.1 0.1 0.2 0.8 0.9 0.5 -0.6 0.4 0.5 1.1 0.3 0.3 0.2 0.5 0.3 0.0 0.2 0.1 0.1 -0.3 -0.2 -0.2 -0.7 Page 22 of 32 -0.4 -0.5 -0.8 0.2 0.7 0.1 0.2 0.7 0.5 0.3 0.3 0.1 0.5 0.2 -0.9 -0.2 -2.1 -2.3 -2.1 -0.7 -0.9 -3.4 -0.4 -1.2 -1.2 -0.7 -0.9 -0.5 -1.0 0.6 0.2 -0.2 -0.9 0.4 0.1 0.4 0.1 -0.2 0.1 -0.1 0.1 -1.0 -1.3 -0.9 -0.9 -0.9 -1.3 -0.5 -1.7 0.0 0.1 0.0 0.3 -0.3 -0.6 -1.0 -0.4 -0.3 -0.4 -0.3 -0.7 -0.9 -0.7 -1.7 -1.1 -2.3 -1.8 -2.0 -1.0 -1.1 -3.5 1.6 -0.9 -1.1 -0.9 -1.0 -0.6 -1.0 0.1 0.0 -0.4 -1.1 0.0 -0.3 0.4 -0.1 -0.2 -0.5 -0.3 -0.1 -0.5 -0.5 -0.5 -0.4 -0.6 -1.1 -0.8 -1.3 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 9.7 10.1 9.3 9.5 9.3 9.5 9.6 9.8 10.2 10.1 10.4 8.9 9.0 8.8 9.7 9.5 9.5 10.3 11.4 11.0 10.3 10.1 10.1 9.5 11.5 11.5 10.9 9.6 10.2 9.8 8.4 8.5 8.6 8.6 8.7 8.6 8.4 8.3 8.6 8.7 8.6 8.7 8.9 10.3 9.6 9.1 8.6 8.9 8.6 -0.2 -0.8 -0.3 -0.6 -0.3 0.4 0.0 0.0 -0.9 0.8 -0.3 0.5 0.7 0.1 -0.8 -0.3 0.7 -0.6 -1.0 -0.1 0.0 0.3 -0.1 0.1 -1.4 -1.5 -0.6 -0.3 -1.1 0.4 1.2 0.8 0.7 0.9 1.3 1.2 1.6 1.2 0.9 1.5 1.8 -1.0 1.1 0.4 0.5 0.3 2.4 0.6 0.6 Page 23 of 32 -1.3 -1.4 -0.6 -0.5 -0.8 0.6 -0.8 -0.7 -0.9 -1.3 -1.4 -0.2 -0.1 0.0 -1.0 -0.9 -1.0 -1.6 -2.9 -2.4 -1.7 -1.7 -1.3 -0.8 -2.8 -2.5 -2.1 -0.7 -1.2 -0.9 1.2 0.8 0.6 1.1 0.3 0.8 0.7 0.5 0.6 0.4 0.2 0.0 -0.5 -1.6 -0.2 0.5 0.3 0.4 0.1 -0.5 -1.1 -0.7 -0.6 -0.5 0.4 0.9 0.0 -0.5 0.6 -0.2 0.6 0.7 0.6 -0.2 0.1 0.5 -1.0 -1.7 -1.3 -0.9 -0.5 0.1 0.5 -1.3 -1.5 -1.3 0.0 -0.9 0.5 0.7 0.9 1.0 0.5 0.4 0.9 0.5 0.6 0.4 0.5 0.5 0.1 0.1 -0.9 -0.1 0.0 0.9 0.6 0.5 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 9.6 8.9 9.3 8.7 9.1 8.8 9.3 9.6 9.9 9.6 9.6 9.7 9.0 9.4 9.3 9.6 9.4 9.1 9.6 11.0 11.2 11.0 9.9 10.7 9.5 11.4 10.8 11.1 9.8 9.7 9.9 8.3 8.9 9.2 9.8 8.7 9.0 8.7 8.9 8.9 9.0 8.9 8.8 9.4 9.8 9.3 9.6 9.3 9.8 1.8 0.6 1.4 0.3 1.8 0.9 -0.8 -0.3 -0.9 -0.8 -0.4 -0.9 0.1 -0.3 -0.1 -0.4 0.2 -0.3 -0.7 -0.9 -2.1 -1.8 -0.6 -1.4 -0.1 -2.2 -1.7 -1.9 -0.7 -0.5 -1.0 1.6 1.6 0.6 1.2 2.8 2.1 1.2 1.3 0.8 0.9 1.0 0.8 1.5 0.1 0.8 0.5 1.3 1.2 Page 24 of 32 -0.3 0.5 0.0 0.8 0.1 0.5 -0.7 -0.4 -1.0 -1.0 -0.7 -1.1 0.5 -0.3 -0.2 -0.8 -0.9 -0.3 -1.1 -2.4 -2.6 -2.5 -1.0 -1.8 -0.5 -3.0 -2.2 -2.5 -0.9 -0.6 -1.3 1.0 0.5 0.2 0.0 1.2 1.2 0.8 0.9 1.0 0.6 0.8 1.2 -0.2 -0.6 0.0 -0.5 0.0 0.5 -0.1 0.5 0.6 0.5 0.5 0.7 0.4 -0.6 -0.3 -0.8 -0.5 -0.2 0.2 -0.4 0.0 0.1 0.2 1.1 0.1 -0.4 -1.6 -1.1 -0.3 -1.0 1.0 -1.2 -1.2 -1.3 0.1 0.3 -0.1 0.2 0.1 -0.5 -0.8 0.1 0.2 -0.5 0.0 -0.5 -0.6 0.0 0.1 0.1 0.1 0.2 -0.2 0.4 -0.2 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 9.8 10.5 9.7 10.1 9.3 9.5 9.3 8.9 10.0 10.1 9.6 9.7 10.0 9.2 9.4 9.8 9.4 10.1 9.5 10.1 11.1 11.5 10.3 10.1 10.0 10.1 10.4 10.2 10.5 10.5 9.5 9.9 0.6 0.0 0.5 0.2 0.3 0.2 0.7 0.1 -0.8 -1.0 -0.7 1.8 -0.5 -0.5 -0.3 -0.8 -0.1 -0.2 -0.5 0.0 -0.6 -1.4 -0.4 -0.2 0.0 0.2 -0.2 0.2 -0.5 -0.5 -0.4 -0.2 Page 25 of 32 -0.9 -1.0 -0.1 -0.6 0.0 0.5 -0.3 0.3 -0.8 -0.4 0.0 -0.5 -0.5 -0.2 0.1 -0.3 -0.3 -1.0 0.0 -0.6 -2.3 -2.7 -1.5 -1.4 -0.9 -1.4 -1.4 -0.8 -1.8 -1.6 -0.4 -1.3 0.0 -0.3 0.1 0.1 0.3 0.0 0.2 0.1 -1.0 -1.2 -0.5 -0.2 0.0 -0.8 -0.5 -0.6 -0.4 -0.5 -0.3 -0.4 -1.2 -2.1 -1.0 -0.2 -0.7 -1.0 -0.1 -0.4 -1.1 -0.6 0.0 -0.7 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM DATA Continued GAS TIGHT: Board 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 mOhm values Position P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 Actual Initial 9.2 9.6 9.6 9.4 9.2 11.1 9.8 10.1 9.3 9.0 11.2 11.4 10.1 10.4 10.6 10.2 8.8 9.6 9.2 10.6 9.5 9.1 9.3 10.2 8.8 9.4 9.6 11.0 9.6 12.8 9.7 9.3 9.8 9.9 9.6 10.0 10.5 11.5 9.8 10.4 9.0 Delta Gas Tight 0.4 -0.3 0.2 -0.4 -0.2 -1.4 0.0 -0.4 0.0 0.1 -1.4 -1.4 -1.1 -1.1 -1.6 -1.2 -0.1 -0.7 -0.3 -1.2 -0.4 -0.3 -0.4 -0.9 -0.3 -0.4 -0.3 -1.5 -0.4 -3.5 -0.3 -0.1 0.7 -0.7 -0.4 -0.8 -0.9 -2.5 -1.0 -1.3 -0.3 Page 26 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P14 P15 P16 P17 P18 9.5 9.9 9.7 10.7 11.4 11.9 10.0 9.0 9.8 9.7 11.3 10.4 10.9 10.8 11.9 10.0 10.8 11.0 10.4 10.9 10.7 9.0 10.0 10.7 9.8 9.7 9.7 9.2 10.4 9.6 9.7 9.4 9.4 8.8 9.1 9.1 8.8 9.1 9.0 10.2 9.3 8.7 9.1 9.3 8.7 8.7 8.6 8.8 8.7 -0.7 -0.9 -0.6 -1.2 -2.0 -2.6 -0.9 0.6 -0.6 -0.1 -1.2 -0.5 -0.7 -1.1 -0.7 0.3 -0.7 -1.3 -0.5 -1.1 -1.0 -0.4 -1.0 -1.2 -1.1 -0.5 -0.7 -0.3 -0.6 -0.1 -0.3 0.0 -0.3 0.1 0.2 0.6 0.2 0.1 0.1 -0.6 0.6 1.0 -0.1 0.5 0.9 -0.1 -0.1 -0.1 0.0 Page 27 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 8.6 8.7 8.7 8.7 8.5 8.5 10.1 9.2 9.6 9.7 10.6 9.7 10.7 9.4 9.4 9.4 9.9 9.1 9.8 9.2 9.2 9.3 9.5 9.4 9.3 9.4 9.7 9.8 8.7 9.3 12.7 9.9 10.6 11.6 10.1 9.2 10.7 8.9 10.4 11.5 12.4 11.1 10.7 10.7 9.7 15.5 14.8 14.4 14.7 -0.4 0.0 -0.1 0.0 0.2 0.1 -1.7 -0.5 0.2 -0.9 -1.1 -0.7 -0.7 -0.2 -0.4 0.1 -1.0 0.4 -0.9 -0.5 -0.4 -0.1 0.2 -0.2 -0.2 -0.1 -0.5 -0.6 0.5 -0.4 -2.1 0.0 -0.9 1.2 -0.3 -0.2 -0.7 -0.4 -0.9 0.7 1.0 -0.6 -0.3 -0.2 -0.3 -0.5 -0.1 -0.5 -0.9 Page 28 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM 6 6 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 14.7 10.9 9.5 11.2 10.4 10.7 10.4 10.9 9.3 10.8 10.9 10.0 10.5 9.8 12.0 9.9 10.8 11.0 10.0 10.8 10.6 10.1 10.7 9.9 10.0 10.2 10.0 10.5 10.8 10.8 11.7 11.1 10.6 9.6 10.5 9.2 10.3 9.7 11.5 12.0 9.4 9.0 8.9 8.8 9.5 8.7 -0.6 -1.4 -0.7 -0.5 -0.6 -1.1 -1.1 -0.6 -0.2 -0.8 -1.4 -0.6 -0.5 1.6 -2.9 -0.5 -1.7 -0.8 -0.5 -1.4 -1.0 -0.4 -1.6 -1.1 -0.5 0.2 -0.4 -0.5 -1.2 -1.0 -1.5 -0.8 -0.7 0.3 -0.8 0.1 -0.9 -1.0 -1.8 -3.0 -0.5 -0.4 0.3 0.2 -0.2 0.2 Page 29 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM EQUIPMENT AND CALIBRATION SCHEDULES Equipment #: MO-03 Description: Multimeter /Data Acquisition System Manufacturer: Keithley Model: 2700 Serial #: 0791975 Accuracy: See Manual … Last Cal: 06/22/07, Next Cal: 06/22/08 Equipment #: MO-01 Description: Micro-Ohmeter Manufacturer: Keithley Model: 580 Serial #: 0772740 Accuracy: See Manual … Last Cal: 06/22/07, Next Cal: 06/22/08 Equipment #: OV-03 Description: Cascade Tek Forced Air Oven Manufacturer: Cascade Tek Model: TFO-5 Serial #: 0500100 Accuracy: Temp. Stability: +/-.1C/C change in ambient … Last Cal: 06/62/07, Next Cal: 06/22/08 Equipment #: MO-06 Description: Micro-Ohmeter Manufacturer: Keithley Model: 580 Serial #: 1110525 Accuracy: See Manual … Last Cal: 06/22/2007, Next Cal: 06/22/2008 Equipment #: MO-07 Description: Multimeter / Data Acquistion System Manufacturer: Keithley Model: 2700 Serial #: 1116559 Accuracy: See Manual … Last Cal: 6/22/2007, Next Cal: 6/22/2008 Page 30 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM Equipment #: TCT-03 Description: Dillon Quantrol TC2 Test Stand Manufacturer: Dillon Quantrol Model: TC2 Serial #: 02-1033-03 Accuracy: Speed Accuracy: +/- 5% of indicated speed; Displacement: +/- 5 micrometers. … Last Cal: 5/18/07, Next Cal: 5/18/08 Equipment #: TCT-04 Description: Dillon Quantrol TC21 25-1000 mm/min series test stand Manufacturer: Dillon Quantrol Model: TC2 I series test stand Serial #: 04-1041-04 Accuracy: Speed Accuracy: +/- 5% of indicated speed; Speed Accuracy: +/- 5% of indicated speed; … Last Cal: 05/18/2007, Next Cal: 05/18/2008 Equipment #: LC-250N (icell)-1 Description: 250 Newton load cell for Dillon Quantrol test stand Manufacturer: Dillon Quantrol Model: icell Serial #: 04-0020-08 Accuracy: .10 % of Capacity … Last Cal: 01/18/2008, Next Cal: 01/18/2009 Equipment #: OGP-02 Description: Automatic Video Meauring System, 18" (X) x 18" (Y) x 12" (Z) Manufacturer: Optical Gaging Products (OGP) Model: Smartscope Flash Serial #: SVL 5001462 Accuracy: See Manual … Last Cal: 03/13/2007, Next Cal: 03/13/2008 Equipment #: LC-100N (icell)-1 Description: 100N load cell for Dillon Test stand Manufacturer: Mecmesin (Dillon/Quantrol) Model: icell Serial #: 06-0358-08 Accuracy: .10 % of capacity … Last Cal: 01/18/2008, Next Cal: 01/18/2009 Page 31 of 32 Tracking Code: TC073--1549 Part #: SEM-125-02-03.0-H-D-WT/ TEM-125-02-03.0-H-D-WT Part description: SEM/TEM Equipment #: OGP-01 Description: 6''X 6'' Video Measuring Machine Manufacturer: Optical Gauging Products Model: Smartscope 200 CFOV Serial #: 0791975 Accuracy: See Manual … Last Cal: 03/13/07, Next Cal: 03/13/08 Equipment #: LC-5N (icell)-2 Description: 5 Newton load cell for Dillon Quantrol test stand Manufacturer: Dillon Quantrol Model: icell Serial #: 02-0140-05 Accuracy: .10 % of capacity … Last Cal: 5/24/2007, Next Cal: 5/24/2008 Equipment #: HPM-01 Description: Hipot Megommeter Manufacturer: Hipotronics Model: H306B-A Serial #: M9905004 Accuracy: 2 % Full Scale Accuracy … Last Cal: 06/22/07, Next Cal: 06/22/08 Equipment #: STG-01 Description: Hipot Megomter Safety Test Cage Manufacturer: Hipotronics Model: TC-25 Serial #: M9910141 Accuracy: N/A … Last Cal: No Calibration Required, Next Cal: Equipment #: Null Description: Manufacturer: Model: Serial #: Accuracy: … Last Cal: , Next Cal: Page 32 of 32