AD6C111-L - Solid State Optronics

AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
Description
Features
The AD6C111-L is a bi-directional, single-pole, singlethrow, normally open solid-state relay. It provides a load
current of 110mA, a high blocking voltage of 400V, and
current limiting circuitry in a compact 6 pin DIP package.
Current limiting circuitry provides a level of protection
against increased load currents or transient current spikes
by active current reduction across the device, thereby
protecting itself and downstream components.

High Isolation Voltage (3750VRMS)

Low Input Control Current (2.5mA TYP)

110mA Maximum Continuous Load Current

40 Maximum On-Resistance

Active Current Limiting Protection

Long Life / High Reliability

RoHS / Pb-Free / REACH Compliant
The AD6C111-L comes standard in a miniature 6 pin DIP
package making it ideal for high-density board applications.
Agency Approvals
Applications
UL / C-UL:
VDE:

Reed Relay Replacement

Multiplexers

Meter Reading Systems

Medical Equipment

Battery Monitoring
Absolute Maximum Ratings
The values indicated are absolute stress ratings. Functional
operation of the device is not implied at these or any
conditions in excess of those defined in electrical
characteristics section of this document. Exposure to
absolute Maximum Ratings may cause permanent damage
to the device and may adversely affect reliability.
Schematic Diagram
(+) Input
1
(-) Input
2
File # E201932
File # 40035191 (EN 60747-5-2)
Storage Temperature …………………………..-55 to +125°C
Operating Temperature …………………………-40 to +85°C
Continuous Input Current ………………………………..50mA
Transient Input Current ………………….……………..500mA
Reverse Input Control Voltage …………..…………………6V
Input Power Dissipation …………………………………40mW
Output Power Dissipation ……………………………..800mW
Solder Temperature – Wave (10sec)……………….….260°C
Solder Temperature – IR Reflow (10sec)….…………..260°C
6
-/+ Load
5
DC Connection
4
-/+ Load
ILIMIT
Do Not Use
3
Ordering Information
Part Number
AD6C111-L
AD6C111-L
AD6C111-LS
AD6C111-LSTR
Description
6 pin DIP, (50/Tube)
6 pin SMD, (50/Tube)
6 pin SMD, Tape and Reel (1000/Reel)
NOTE: Suffixes listed above are not included in marking on
device for part number identification
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 1 of 9
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520
AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
Electrical Characteristics, TA = 25°C (unless otherwise specified)
Parameter
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Input Specifications
LED Forward Voltage
VF
-
1.2
1.5
V
IF = 10mA
LED Reverse Voltage
BVR
6
-
-
V
IR = 10μA
Turn-On Current
IF
-
2.5
5.0
mA
IO = 110mA
Turn-Off Current
IFOFF
-
0.5
-
mA
-
Blocking Voltage
VB
400
-
-
V
IO=1A
Continuous Load Current
IO
-
-
110
mA
IF=5mA
Current Limit (AC or DC connection)
ILIMIT
160
300
-
mA
IF=5mA
On Resistance
RON
-
30
40
Ω
IF=5mA, IO=110mA
Leakage Current
IOleak
-
0.2
1
A
IF=0mA, VO=400V
Output Specifications
Output Capacitance
COUT
-
25
50
pF
IF=0mA, f=1.0MHz
VOFFSET
-
-
0.2
mV
IF=5mA
Turn-On Time
TON
-
1.5
5.0
mS
IF=5mA, IO=110mA
Turn-Off Time
TOFF
-
0.5
1.0
mS
IF=0mA, IO=110mA
Offset Voltage
Coupled Specifications
Coupled Capacitance
Contact Transient Ratio
CCOUPLED
-
3
-
pF
-
2,000
7,000
0
V/S
VISO
3,750
-
-
VRMS
RH ≤ 50%, t=1min
-

VI-O = 500VDC
dV = 50V
Isolation Specifications
Isolation Voltage
Input-Output Resistance
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
RI-O
-
10
Page 2 of 9
12
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520
AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
AD6C111-L Current Limiting Connection Diagrams, TA = 25°C (unless otherwise specified)
Connection Diagrams
Comments
Option A: Normal AC Load Configuration
On Resistance:
RTYP
Current Limit:
ILIMIT
Option B: Separate Loads & Load Voltages
On Resistance:
Load1
Load2
Current Limit:
Load1
Load2
~ (RTYP / 2) + 3
RTYP / 2
ILIMIT
N/A
- Sum power of loads not to exceed maximum
package power dissipation
Option C: DC Load with Minimal Resistance and No Current Limit
On Resistance:
Current Limit:
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 3 of 9
RTYP / 4
None
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520
AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
AD6C111-L Performance & Characteristics Plots, TA = 25°C (unless otherwise specified)
I =5mA
F
I =110mA
O
I =5mA
F
I =110mA
O
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 4 of 9
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520
AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
AD6C111-L Solder Temperature Profile Recommendations
(1) Infrared Reflow:
Refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow.
Soldering process should not exceed temperature or time limits expressed herein. Surface temperature of device
package should not exceed 250ºC:
G
F
D
E
H
B
A
C
Figure 1
Process
Step
A
B
C
D
E
F
G
H
Description
Preheat Start Temperature (ºC)
Preheat Finish Temperature (ºC)
Preheat Time (s)
Melting Temperature (ºC)
Time above Melting Temperature (s)
Peak Temperature, at Terminal (ºC)
Dwell Time at Peak Temperature (s)
Cool-down (ºC/s)
Parameter
150ºC
180ºC
90 - 120s
230ºC
30s
260ºC
10s
<6ºC/s
(2) Wave Solder:
Maximum Temperature:
Maximum Time:
Pre-heating:
Single Occurrence
260ºC (at terminal)
10s
100 - 150ºC (30 - 90s)
(3) Hand Solder:
Maximum Temperature:
Maximum Time:
Single Occurrence
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
350ºC
3s
(at tip of soldering iron)
Page 5 of 9
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520
AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
AD6C111-L Package Dimensions
6 PIN DIP Package
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Note:
Page 6 of 9
All dimensions in inches [“] with millimeters in parenthesis ()
Device Weight: 0.45g
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520
AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
AD6C111-L Package Dimensions
6 PIN SMD Surface Mount Package (-S)
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Note:
Page 7 of 9
All dimensions in inches [“] with millimeters in parenthesis ()
Device Weight: 0.45g
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520
AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
AD6C111-L Package Dimensions
6 PIN SMD Tape & Reel (-STR)
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Note:
Page 8 of 9
All dimensions in millimeters
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520
AD6C111-L
1 Form A, Current Limiting
400V / 40 Ω
MOSFET Output Solid State Relay
AD6C111-L Package Marking
DISCLAIMER
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO
reserves the right to make changes to product description, specifications at any time without further notices.
SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent
licenses nor indemnity are expressed or implied.
Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other
warranty, expressed or implied, including merchantability and fitness for particular use.
LIFE SUPPORT POLICY
SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or
death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all
damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be
reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be
reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness.
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 9 of 9
AD6C111-L/S/TR
Rev 2.00 (08/28/2012)
001520