Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Applications



Product Description
The SE2614BT is a complete 802.11bgn WLAN RF
front-end module providing all the functionality of the
power amplifier, power detector, SP3T Switch and 50
ohm matching on all RF ports in an ultra compact
form factor.
IEEE802.11b DSSS WLAN
IEEE802.11g,n OFDM WLAN
Access Points, PCMCIA, PC cards
Features







Dual Mode IEEE802.11b, IEEE802.11g,
IEEE802.11n
Integrated PA, TX Filter, SP3T switch
Integrated Positive Slope Power Detector
20 dBm Output Power, 802.11b, 11 Mbps
18 dBm @ 3.0 % EVM, 802.11g, 3.3V
Lead free, halogen free and RoHS compliant
Small plated package, 3 mm x 3 mm x 0.6 mm,
MSL 1
The SE2614BT is designed for ease of use, with all
the critical matching and harmonic filtering integrated.
The SE2614BT also includes a transmitter power
detector with 20 dB of dynamic range and a digital
enable control for transmitter power on/off control.
The power ramp rise/fall time is 0.1 μs typical.
Ordering Information
Part No.
Package
Remark
SE2614BT
SE2614BT-R
SE2614BT-EK1
20 lead QFN
20 lead QFN
N/A
Samples
Tape & Reel
Evaluation kit
Functional Block Diagram
Figure 1: Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
1
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Pin Out Diagram
Figure 2: SE2614BT Pin Out (Top View Through Package)
Pin Out Description
Pin
Name
1
DET
2
EN
3
Description
Pin
Name
Description
Power Detector output
11
CPORT2
Switch Control Logic – Port 2 path
TX Enable
12
CPORT1
Switch Control Logic – Port 1 path
VCC0
Supply Voltage – Pre-driver & Driver
13
GND
4
TXIN
TX input
14
ANT
Antenna Output
5
GND
Ground
15
GND
Ground
6
GND
Ground
16
GND
Ground
7
PORT1
Port 1 – May be used for RX or BT
17
GND
Ground
8
GND
Ground
18
Vcc3
Supply Voltage Power Stage
9
PORT2
Port 2 – May be used for RX or BT
19
GND
Ground
10
CTX
Switch Control Logic – TX path
20
Vcc2
Supply Voltage
Ground
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
2
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage
to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions
defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected
workstations.
Symbol
Min.
Max.
Unit
Supply Voltage on VCC
-0.3
3.6
V
VIN
DC input on EN, CTX, CPORT1, CPORT2
-0.3
3.6
V
TX
RF Input Power.
-
12.0
dBm
TA
Operating Temperature Range
-40
85
°C
Storage Temperature Range
-40
150
°C
-
1
KV
VCC
TSTG
ESD HBM
Definition
JEDEC JESD22-A114 all pins to Ground
Recommended Operating Conditions
Symbol
TA
VCC
Parameter
Min.
Typ.
Max.
Unit
Ambient temperature
-40
25
85
°C
VCC0, VCC2, VCC3, supply voltage
3.0
3.3
3.6
V
DC Electrical Characteristics
Conditions: VCC = EN = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board,
all unused ports terminated with 50 ohms, unless otherwise noted
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
ICC-G
Total Supply Current
POUT = 18 dBm, 54 Mbps
OFDM signal, 64QAM
-
160
-
mA
ICC-B
Total Supply Current
POUT = 20 dBm, 11 Mbps
CCK signal, BT = 0.45
-
190
-
mA
ICQ
Total Supply Current
No RF
-
90
-
mA
Icntl
Control Line Current
CTX, CPORT2, CPORT1 =
3.3V
1
10
μA
ICC_OFF
Total Supply Current
No RF Applied, EN = CTX =
CPORT1 = CPORT2 = 0 V
1
10
μA
-
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
3
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
PA Logic Characteristics
Conditions: VCC = EN = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board,
all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
VENH
Logic High Voltage
(Module On)
-
1.6
3.3
3.6
V
VENL
Logic Low Voltage
(Module Off)
-
0
-
0.4
V
IENH
Input Current Logic
High Voltage
-
-
330
400*
μA
IENL
Input Current Logic
Low Voltage
-
-
2
10
μA
*due to on chip pulldown resistor
Switch Logic Characteristics
Conditions: VCC = EN = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board
(de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
VCTL_ON
VCTL_OFF
Parameter
Conditions
Min.
Typ.
Max.
Unit
-
1.6
3.3
3.6
V
-
0.0
-
0.4
V
200
-
nSec
-
1
pF
Control Voltage
(On State)
Control Voltage
(OFF State)
Tswitch
T/R Switching Speed
CCTL
Control Input
Capacitance
VCTL_OFF -> VCTL_ON
VCTL_ON -> VCTL_OFF
-
-
Switch Control Logic Table
Allowed Switch Logic
CPORT1
CPORT2
CTX
PORT1 – ANT
PORT2 – ANT
TX-ANT
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
All Other States
Not Supported
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
4
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
AC Electrical Characteristics
802.11g/n Transmit Characteristics
Conditions: VCC = EN = CTX = 3.3 V, CPORT1 = CPORT2 = 0 V, TA = 25 C, as measured on Skyworks
Solutions’ SE2614BT-EK1 evaluation board, all unused ports terminated with 50 ohms, unless
otherwise noted.
Symbol
FIN
POUT
ACPR,
IEEE
Mask
P1dB
S21
Parameter
Condition
Min.
Typ.
-
2400
-
2500
MHz
Output Power
54 Mbps OFDM signal, 64
QAM, 3% EVM
-
18
-
dBm
Spectral Mask
POUT = 20 dBm, 11 Mbps
CCK, BT = 0.45
11 – 22 MHz
22 – 33 MHz
-
-
dBc
Frequency Range
-35
-55
Max.
Unit
P1dB
-
-
25
-
dBm
Small Signal Gain
-
-
30
-
dB
+1.5
dB
Small Signal Gain vs
Temp
Measured at single freq
from -40°C to 85°C
Small Signal Gain
Variation
Gain variation over single
40MHz channel
Gain Variation over band
-
0.5
-
-
1.1
-
Gain @ limit 3.2Ghz
3206 to 3312 MHz
-
10
15
dB
Harmonics
POUT = 20 dBm, 1 Mbps,
DSSS
-
-50
-45
dBm/MHz
-
-50
-45
dBm/MHz
tdr, tdf
Delay and rise/fall
Time
50 % of VEN edge and
90/10 % of final output
power level
-
0.2
-
μs
S11
Input Return Loss
-
10
-
dB
∆S21_T
∆S21
S213.2
2f
3f
STAB
RU
-
-1.5
dB
Stability
CW, POUT = 20 dBm
0.1 GHz – 20 GHz
Load VSWR = 6:1
All non-harmonically related outputs less than
-42 dBm/MHz
Ruggedness
PIN = 12dBm,
Load VSWR = 6:1
No permanent damage
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
5
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Receive and BT Characteristics
Conditions: VCC = 3.3 V, EN = CTX = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1
evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FOUT
Parameter
Frequency Range
Condition
Min.
Typ.
-
2400
-
2500
Unit
MHz
dB
CPORT1 = 0 V and CPORT2 =
3.3 V
or
CPORT1 = 3.3 V and CPORT2 =
0V
-
1.2
-
PORT1 or PORT2
15
20
-
-
-
1.2
-
PORT1 or PORT2
15
20
-
dB
200
250
nSec
25
-
dB
RXIL
Insertion Loss
RXRL
Return Loss
BTIL
Insertion Loss
BTRL
Return Loss
Ton/off
T/R on/off switching
speed
Switching speed between T/R
modes. Vcc0=3.3V.
Isolation between
ANT and
PORT1/PORT2
Difference in signal level on
PORT1 or PORT2 when
transmitting from TX.
CTX = 3.3V, CPORT1 =
CPORT2 = 0V
PORT1 and PORT2 terminated
in 50ohm.
ANTRISOL
Max.
-
dB
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
6
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Power Detector Characteristics
Conditions: VCC = EN = CTX = 3.3 V, CPORT1 = CPORT2 = 0 V, TA = 25 C, as measured on Skyworks Solutions’
SE2614BT-EK1 evaluation board, unless otherwise noted.
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
-
2400
-
2500
MHz
FOUT
Frequency Range
PDR
Power detect range,
CW
Measured at ANT
0
-
21
dBm
PDVNoRF
Output Voltage, POUT =
No RF
Measured into 26KΩ
-
0.35
-
V
PDVP18
Output Voltage, POUT =
18 dBm CW
Measured into 26KΩ
-
0.68
-
V
PDVP21
Output Voltage, POUT =
22 dBm CW
Measured into 26KΩ
-
0.83
-
V
Detector output
impedance
Zout
LPF-3dB
1
Power detect low pass
filter -3dB corner
frequency
PDCLOAD = High Z (1MΩ)
-
KΩ
500
-
KHz
1.2
1.1
1.0
Pdet(V)
0.9
0.8
0.7
0.6
0.5
0.4
0.3
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Pout (dBm)
Figure 3: SE2614BT Power Detector Characteristics
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
7
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Package Diagram
20
19
18
17
16
16
17
18
19
20
1
15
15
1
2
14
14
2
3
13
13
3
4
12
12
4
5
11
11
5
6
7
8
9
TOP VIEW
10
10
9
8
7
6
BOTTOM VIEW
Figure 4: SE2614BT Package Outline Drawing
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
8
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Recommended Land and Solder Patterns
20
19
18
17
16
17
1
15
2
14
3
13
4
12
5
11
16
15
13
5
6
7
8
9
10
6
20
19
18
17
16
20
8
19
18
17
16
1
15
1
15
2
14
2
14
3
13
3
13
4
12
4
12
5
11
5
11
6
7
8
9
10
6
7
8
9
10
Figure 5: Recommended Land and Solder Patterns
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
9
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Package Handling Information
Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed
regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption
may occur when the part is subjected to high temperature during solder assembly. The SE2614BT is capable of
withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or
in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that
the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For
details on both attachment techniques, precautions, and handling procedures recommended, please refer to:
 “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045
 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044
Caution! ESD sensitive device
Branding Information
Pin 1 Designator
Pin 1
Company Name
Part Number
Lot Code
SiGe
2527L
614B
Lot Code
Figure 6: SE2614BT Branding Information
Tape and Reel Information
Parameter
Devices Per Reel
Reel Diameter
Tape Width
Value
3000
13 inches
12 millimeters
Figure 7: SE2614BT-R Tape and Reel Information
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
10
DATA SHEET
SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End
Document Change History
Revision
Date
Notes
1.0
January 17, 2011
Created
1.1
February 3, 2011
Updated MSL rating and landing pattern.
1.2
June 15, 2011
Updated ESD rating to 1KV
1.3
April 03, 2012
Updated with Skyworks logo and disclaimer statement
1.4
July 9, 2014
Removed PRELIMINARY from header. Updated disclaimer statement
Copyright © 2012, 2014 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein,
are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or
omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time,
without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other
difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials,
products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in
Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE,
INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL
SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR
OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT,
INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE
MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to
personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to
fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or
operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks.
Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated
published specifications or parameters.
Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names
are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at
www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014
11