Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
SE2611T: 2.4 GHz High Efficiency Wireless LAN/BT Front End
Applications
 Simultaneous WLAN and Bluetooth receive mode
 Direct connection to battery with 3.3 V nominal supply
 Lead-free, halogen-free, ROHS compliant QFN (20-pin,
3  3  0.6 mm) package (MSL1, 260 C per JEDEC J-STD020)
The SE2611T also includes a transmitter power detector with
20 dB of dynamic range and a digital enable control for
transmitter power ramp on/off control. The power ramp rise/fall
time is 0.5 s typical.
The device package and pinout for the 20-pin QFN are shown in
Figure 1. A block diagram of the SE2611T is shown in Figure 2.
VCC2
Skyworks Green™ products are compliant with
all applicable legislation and are halogen-free.
For additional information, refer to Skyworks
Definition of Green™, document number
SQ04-0074.
The SE2611T includes a low noise amplifier to increase the
receive sensitivity of embedded solutions to improve range or to
overcome the insertion loss of cellular filters often included for
mobile applications. It offers simultaneous WLAN and Bluetooth
receive mode.
20
19
18
17
DET
 19 dBm @ 4.0 % EVM, 802.11g, 54 Mbps
The SE2611T is designed for ease of use, with all the critical
matching and harmonic filtering integrated, also offering a simple
50  interface to the antenna.
16
DNC
1
15 DNC
CRX
2
14 TX
DNC
3
13 GND
CTX
4
12 RX
NC
5
11 BT
ANT
6
7
8
9
10
NC
 Integrated positive slope power detector
VCC1
 Integrated PA, harmonic filter, LNA and BT port
GND
 Dual mode IEEE802.11b & IEEE802.11g
PEN
Features
LEN
 Embedded applications with Bluetooth® (Mobile)
The SE2611T is a complete 802.11 b/g/n WLAN RF front-end
module with a Bluetooth port. The device provides all the
functionality of the power amplifier, power detector, filter, switch,
Low Noise Amplifier (LNA), 2170 MHz notch filtering and
associated matching. The SE2611T provides a complete 2.4 GHz
WLAN RF solution from the output of the transceiver to the
antennas, and from the antennas to the input of the transceiver, in
an ultra-compact form factor.
CBTR
 IEEE 802.11g/n OFDM WLAN
Description
CBTB
 IEEE 802.11b DSSS WLAN
Y0974
Figure 1. SE2611T Pinout – 20-Pin QFN
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202404B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 30, 2014
1
DATA SHEET • SE2611T 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
BT
CBTR
4
4
1
2
RX
ANT
3
VCC1
VCC1
VCC2
TX
DET
LEN
1
CBTB
2
CRX
3
CTX
Y0957
PEN
Figure 2. SE2611T Block Diagram
Electrical and Mechanical Specifications
SE2611T are provided in Table 2. Recommended operating
conditions are specified in Table 3. Electrical specifications are
provided in Tables 4 through 10, and Figure 3.
Signal pin assignments and functional pin descriptions are
described in Table 1. The absolute maximum ratings of the
Table 1. SE2611T Signal Descriptions
Pin
Name
Description
Pin
Name
Description
1
DNC
Do not connect
11
BT
Bluetooth port
2
CRX
WLAN receive antenna switch control
12
RX
WLAN receive port
3
DNC
Do not connect
13
GND
Ground
4
CTX
WLAN transmit antenna switch control
14
TX
WLAN transmit port
5
NC
No connect
15
DNC
Do not connect
6
ANT
Antenna port
16
DET
Transmit power detector output
7
CBTB
Bluetooth antenna switch control
17
VCC1
Power amplifier power supply
8
LEN
LNA enable
18
PEN
Power amplifier enable
9
GND
Ground
19
CBTR
Bluetooth back-end switch control
10
NC
No connect
20
VCC2
Power amplifier power supply
Die paddle
GND
Ground
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2
May 30, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202404B
DATA SHEET • SE2611T: 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
Table 2. SE2611T Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Minimum
Maximum
Units
V
Supply voltage on VCC
VCC
0.3
+6
DC input on EN
VIN
0.3
+3.6
V
Tx input power. ANT terminated in 50  match
PTXIN
5
dBm
Operating temperature range
TA
40
+85
C
Storage temperature range
TSTG
40
+150
C
Electrostatic discharge:
ESD
1000
V
Human Body Model (HBM), Class 1C
Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Table 3. SE2611T Recommended Operating Conditions
Minimum
Typical
Maximum
Units
Ambient temperature
Parameter
TA
Symbol
40
25
85
C
Supply voltage, relative to GND = 0 V
VCC
2.7
3.3
4.8
V
Table 4. SE2611T Electrical Specifications: DC Characteristics (Note 1)
(VCC = VPEN = 3.3 V, TA = +25 C, as Measured on SE2611T-EK1 Evaluation Board, All Unused Ports Terminated with 50 , Unless
Otherwise Noted)
Parameter
Total supply current
Symbol
ICC_G
Test Condition
Min
Typ
Max
Units
POUT = 18 dBm, 54 Mbps OFDM signal, 64QAM
185
210
mA
Total supply current
ICC_B
POUT = 20 dBm, 11 Mbps CCK signal, BT = 0.45
215
248
mA
Quiescent current
ICQ
No RF
133
165
mA
Total supply current
ICC_OFF
PEN = 0 V, no RF applied, CBTR = CBTB = CTX =CRX= 0 V
5
10
A
Total supply current
ICC_LNA
LEN = VCC
8
12
mA
Total supply current in bypass mode
ICC_LNA_BYP
LEN = 0 V
250
280
A
Note 1: Performance is guaranteed only under the conditions listed in this table.
Table 5. SE2611T Electrical Specifications: Control Logic Characteristics (Note 1)
(VCC = VPEN = 3.3 V, TA = +25 C, as Measured on SE2611T-EK1 Evaluation Board, All Unused Ports Terminated with 50 , Unless
Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
Logic high voltage
VIH
1.2
3.3
V
Logic low voltage
VIL
0
0.4
V
Input current logic high voltage
IIH
10
A
Input current logic low voltage
IIL
1
A
Note 1: Performance is guaranteed only under the conditions listed in this table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202404B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 30, 2014
3
DATA SHEET • SE2611T 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
Table 6. SE2611T Control Logic Table
Mode
Mode Description
CTX
CRX
CBTB
PEN
LEN
CBTR
All off
0
0
0
0
0
0
1
BT
0
0
1
0
0
0
2
WLAN Rx, high gain
0
1
0
0
1
0
3
WLAN Rx, low gain
0
1
0
0
0
0
4
WLAN Tx
1
0
0
0
0
0
5
WLAN Tx + PA enabled
1
0
0
1
0
0
6
(BT + WLAN) Rx, high gain
0
1
0
0
1
1
7
(BT + WLAN) Rx, low gain
0
1
0
0
0
1
8
ANT to (BT + WLAN) connect
0
0
1
0
0
1
0
Table 7. SE2611T Electrical Specifications: AC Characteristics (802.11g Transmit) (Note 1)
(VCC = VPEN = 3.3 V, TA = +25 C, as Measured on SE2611T-EK1 Evaluation Board, All Unused Ports Terminated with 50 , Unless
Otherwise Noted)
Parameter
Symbol
Frequency range
fIN
EVM
EVM
Test Condition
Min
Typ
2400
Max
Units
2500
MHz
4
%
32
55
dBc
VCC = 3.3 V, POUT = 19 dBm, 54 Mbps OFDM signal, 64QAM
VCC = 3.0 V, POUT = 18 dBm, 54 Mbps OFDM signal, 64QAM
VCC = 2.7 V, POUT = 17 dBm, 54 Mbps, OFDM signal, 64QAM
POUT = 20 dBm, 11 Mbps CCK, BT = 0.45
Adjacent channel power ratio 11b
ACPRb
37
58
11 MHz offset
22 MHz offset
POUT = 18 dBm, 54 Mbps OFDM, 64QAM
Adjacent channel power ratio 11g
ACPRg
11 MHz offset
20 MHz offset
30 MHz offset
11g - 54 Mbps
11b – 11 Mbps
Out-of-band limited output power
PMAX_OOB
Small signal gain
S21
Small signal gain variation over band
S21
2nd and 3rd harmonics
20
28
40
16
20
17
20
PSDOOB = 43 dBm/MHz, RB = 1 MHz
2310  2390 MHz
2483.5  2500 MHz
dBm
25
27
30
dB
2.0
dBpp
2f
POUT = 20 dBm, 1 Mbps, 802.11b
35
25
dBm/MHz
3f
POUT = 18 dBm, 54 Mbps OFDM signal, 64QAM
52
43
dBm/MHz
Delay & rise/fall time
tDR, tDF
50 % of VPEN edge and 90/10 % of final output power level
0.5
1
s
Input return loss
S11
Tx port
15
10
dB
Small signal gain in WCDMA band
S21WCDMA
2110  2170 MHz, relative to min in-band gain
10
dBr
Output noise power in WCDMA band
PNWCDMA
2110  2170 MHz
POUT = 20 dBm, 1 Mbps, 802.11b
POUT = 18 dBm, 54 Mbps OFDM signal, 64QAM
127
dBm/Hz
Stability
STAB
CW, PIN = 5 dBm, 0.1 GHz  20 GHz, load VSWR = 6:1
All non-harmonically related outputs less
than 43 dBm/MHz
Ruggedness
RGGD
CW, PIN = 5 dBm, 0.1 GHz  20 GHz, load VSWR = 10:1
No permanent damage or performance
degradation
130
Note 1: Performance is guaranteed only under the conditions listed in this table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
4
dBc
May 30, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202404B
DATA SHEET • SE2611T: 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
Table 8. SE2611T Electrical Specifications: Power Detector Characteristics (Note 1)
(VCC = VPEN = 3.3 V, TA = +25 C, as Measured on SE2611T-EK1 Evaluation Board, All Unused Ports Terminated with 50 , Unless
Otherwise Noted)
Parameter
Symbol
Test Condition
Max
Units
2400
Min
Typ
2500
MHz
0
22
dBm
Frequency range
fOUT
Power detect range, CW
PDR
Output impedance
PDZLOAD
Output voltage, POUT = no RF
PDVNORF
Measured into 1 M
0.1
0.125
0.15
V
Output voltage, POUT = 18.5 dBm CW
PDVP18.5
Measured into 1 M
0.56
0.66
0.76
V
Output voltage, POUT = 20 dBm CW
PDVP20
Measured into 1 M
0.70
0.80
0.90
V
Detector variation over temperature
PDtTVAR
30 to 25 C
25 to 85 C
given detector voltage
0.6
0.5
dB
Detector variation over frequency
PDFVAR
2400  2500 MHz,
given detector voltage
0.5
0.5
dB
Detector variation over load VSWR
PDVSWR
Forward power, ANT VSWR 3:1, all phases,
given detector voltage
2
1
dB
Detector bandwidth
PDBW
Measured at ANT
2.2
k
1
MHz
Note 1: Performance is guaranteed only under the conditions listed in this table.
Pow er Detector Response
2400
2450
2500
1.2
1.1
1
VDET (V)
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
10
12
14
16
18
20
22
Output Pow er (dBm )
Y0959
Figure 3. SE2611T Power Detector Characteristics
Table 9. SE2611T Electrical Specifications: Bluetooth Characteristics
(VCC = 3.3 V, TA = +25 C, as Measured on Skyworks Solutions’ SE2611T-EK1 Evaluation Board, All Unused Ports Terminated with 50 ,
Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Frequency range
fOUT
Insertion loss
BTIL
Bt port return loss
S11
CBTB = High, CBTR = CTX = CRX = Low
Switch isolation
ISOLSW
ANT-RX, CBTB = High, CBTR = CTX = CRX = Low
Min
Typ
2400
BT-ANT, CBTB = High, CBTR = CTX = CRX = Low
Max
Units
2500
MHz
1.5
dB
12
dB
1.2
20
dB
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202404B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 30, 2014
5
DATA SHEET • SE2611T 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
Table 10. SE2611T Electrical Specifications: 2.4 GHz Receive Characteristics
(VCC = 3.3 V, LEN = CRX = CBTR = 3.3 V, PEN = CBTB = CTX = 0 V, TA = +25 C, as Measured on Skyworks Solutions’ SE2611T-EK1
Evaluation Board, All Unused Ports Terminated with 50 , Unless Otherwise Noted)
Parameter
Frequency range
Symbol
Test Condition
Min
fOUT
Receive gain, LNA enabled.
S21
Typ
2400
Max
Units
2500
MHz
(BT + WLAN) Rx, high gain
11
13
15
dB
WLAN Rx, high gain only,
LEN = CRX = 3.3 V,
PEN = CBTB = CTX =CBTR= 0 V
14
16
18
dB
0.5
dB
2.5
dB
2400  2485 MHz, over any 20 MHz band
Gain variation
∆S21
Noise figure
NF
Third order intercept
IIP3
Input return loss
S11
8
dB
Reverse isolation
S12
20
dB
Input P1dB
IP1dB
CW
Enable time
tEN
10% to 90% of RX RF power,
from time that LEN is at 50%
Receive gain, LNA bypassed
S21_BYP
LEN = 0 V
Input return loss, LNA bypassed
S11_BYP
LEN = 0 V
Switch isolation
ISOLSW
CBTB = CBTR = Low, CRX = High,
ANT_BT + BT_RX
2.0
3
Package Dimensions
The PCB layout footprint for the SE2611T is provided in
Figure 4. Typical case markings are shown in Figure 5. Package
dimensions for the 20-pin QFN are shown in Figure 6, and carrier
tape dimensions are provided in Figure 7.
Package and Handling Information
Because of its sensitivity to moisture absorption, instructions on
the shipping container label regarding exposure to moisture after
the container seal is broken must be followed. Otherwise,
problems related to moisture absorption may occur when the part
is subjected to high temperature during solder assembly.
The SE2611T is rated to Moisture Sensitivity Level 1 (MSL1) at
260 C. It is capable of withstanding a Pb-free solder reflow. For
additional information, refer to the Skyworks Application Note,
Solder Reflow Information, document number 200164.
dBm
8
20
dBm
500
ns
10
dB
7
dB
20
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment. If the
part is manually attached, precaution should be taken to insure
that the device is not subjected to temperatures above its rated
peak temperature for an extended period of time. For details on
both attachment techniques, precautions, and handling
procedures recommended by Skyworks, please refer to the
following Skyworks Application Notes:

QFN Solder Reflow and Rework Information Application Note,
document number QAD-00045.

Handling, Packing, Shipping and Use of Moisture Sensitive
QFN Application Note, document number QAD-00044.
Production quantities of this product are shipped in a standard
tape and reel format.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
6
dB
May 30, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202404B
0.20
Typ
0
3X 0.62
3.40
0.400
Typ
3X 0.62
DATA SHEET • SE2611T: 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
0.55 Typ
3X 0.62
3.40 1.80
0
0
3X 0.62
0
9X ø0.254
1.80
Via Pattern
(Note 4)
Board Metal
3.40
3.50
0.30
Typ
0.400
Typ
0.20
Typ
0.400
Typ
0.55 Typ
0.65 Typ
3.50
1.60
3.40
0.60 Typ
0.20
Package
Outline
1.60
0.20
0.60 Typ
Stencil Pattern
(Note 5)
Solder Mask Pattern
(Note 6)
56% solder coverage
on center pads
Notes:
1.
2.
3.
4.
All dimensions are in millimeters.
Dimensions and tolerances according to ASME Y14.5M-1994.
Unless specified, dimensions are symmetrical about center lines.
Via hole recommendations: 0.025 mm Cu via wall plating (minimum),
via hole to be filled with conductive paste and plated over.
5. Stencil recommendations: 0.10 mm stencil thickness, laser cut
apertures, trapezoidal walls and rounded corners offer better paste release.
6. Solder mask recommendations: contact board fabricator for recommended
solder mask offset and tolerance.
Y0975
Figure 4. PCB Layout Footprint for the SE2611T
Pin 1
Indicator
Part Number
Lot Code
SiGe
2611T
XXXXX
Y0960
Figure 5. Typical Case Markings
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202404B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 30, 2014
7
DATA SHEET • SE2611T 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
3.00 ± 0.05
A
1.70 ± 0.05
0.55 ± 0.05
0.05 C
0.152 Ref
B
0.30 X 45°
0.02 +0.03
–0.02
Pin 1 Indicator
Pin 1
Indicator
Exposed Pad
1.70 ± 0.05
3.00 ± 0.05
R0.075
Typ
20X 0.25 Min
0.05 C
2X
2X
21X
0.05 C
C
0.05 C
Detail A
0.40
Seating
Plane
4
Side View
Top View
Bottom View
Notes:
1. All measurements are in millimeters.
2. Dimensions and tolerances according to ASME Y14.5M-1994.
3. Unless otherwise specified, the following values apply:
Decimal Tolerance:
Angular Tolerance:
X.X (1 place) ± 0.1 mm
±1/2°
X.XX (2 places) ± 0.05 mm
X.XXX (3 places) ± 0.025 mm
4. Coplanarity applies to the terminals as well as all other bottom surface metallization.
5. Dimension applies to metallized terminal. If terminal tip has a radius, dimension
should not be measured in that radius area.
6. Unless specified, dimensions are symmetrical about center lines.
2X R0.075
Detail A
0.35 ± 0.05
0.20 ± 0.05
5
Scale: 2X
20 Places
0.10 M C A B
0.05 M C
Y0977
Figure 6. SE2611T 20-Pin QFN Package Dimensions
2.0 ± 0.1
(Note 1)
1.75 ± 0.1
ø1.5 Min
A
12.00 ± 0.3
3.30 ± 0.1
ø1.55 ±0.05
4.0 ± 0.1
Y
5.50- ± 0.1
(Note 3)
0.30 ± 0.05
Ref 3°
Pin 1
Indicator
Y
Ref
R0.6
8.00 ± 0.1
0.80 ± 0.1
f
Re 0.35
R
3.30 ± 0.1
Section Y
f
Re 0.50
R
Notes:
View A
1. Measured from center line of sprocket hole to center line of pocket.
2. 10-sprocket hole pitch cumulative tolerance: ±0.20.
3. Measured from center line of sprocket hole to center line of pocket.
4. Other material available.
5. Typical SR of form tape from 105 to 10 11 Ω/sq.
6. All dimensions are in millimeters.
Figure 7. SE2611T 20-Pin QFN Carrier Tape Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8
May 30, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202404B
Y0978
DATA SHEET • SE2611T: 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
Ordering Information
Model Name
SE2611T: 2.4 GHz High Efficiency Wireless LAN/BT Front End
Manufacturing Part Number
SE2611T
Evaluation Board Part Number
SE2611T-EK1
Copyright © 2012-2014 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for
identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by
reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202404B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 30, 2014
9