Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
SE2623L: 2.4 GHz High Power Wireless LAN Power Amplifier
Applications
 DSSS 2.4 GHz WLAN (IEEE 802.11b)
EN
 OFDM 2.4 GHz WLANs:
IEEE 802.11b/g/n
256 QAM IEEE 802.11ac
VCC0
VCC2
Bias and Control
 Access points
RF_IN
 PCMCIA cards
RF_OUT
50 Ω
DET
 PC cards
DET
Features
 Single 5 V supply operation:
+23 dBm, EVM = 1.8 %, MCS8
+26 dBm, EVM = 3 %, 802.11g, OFDM 54 Mbps
+26 dBm, ACPR < –32 dBc, 802.11b
K109
Notes:
• RF_IN is DC-shorted to Ground within the package. Skyworks
recommends an external blocking capacitor.
• RF_OUT is DC-shorted to VCC within the package. The output
match should include the blocking capacitor.
Figure 1. SE2623L Block Diagram
 +33 dB gain
 Integrated temperature-compensated power detector
Description
 Digital power amplifier enable pin (VEN)
The SE2623L is a 2.4 GHz Power Amplifier (PA) designed for use
in the 2.4 GHz Industrial, Scientific, Medical (ISM) band for
wireless Local Area Network (LAN) applications. The SE2623L
device incorporates a power detector for closed loop monitoring
of the output power.
 Small QFN (16-pin, 3.0 x 3.0 x 0.9 mm) package (MSL3, 260 °C
per JEDEC J-STD-020)
GND
VCC1
NC
VCC2
Skyworks Green™ products are compliant with
all applicable legislation and are halogen-free.
For additional information, refer to Skyworks
Definition of Green™, document number
SQ04-0074.
16
15
14
13
2
11
RF_OUT
GND
3
10
RF_OUT
VCC0
4
9
GND
7
8
NC
EN
DET
GND
GND
12
GND
1
6
The SE2623L temperature-compensated power detector is highly
immune to mismatch at its output, with less than +1.5 dB of
variation with a 2:1 mismatch.
A block diagram of the SE2623L is shown in Figure 1. The device
package and pinout for the 16-pin QFN are shown in Figure 2.
RF_IN
5
The SE2623L includes a digital enable control for device on/off
control.
S3375
Figure 2. SE2623L Pinout—16-Pin QFN
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202397E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 27, 2014
1
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
Electrical and Mechanical Specifications
The recommended operating conditions are specified in Table 3.
The electrical specifications are provided in Tables 4 through 7.
The typical performance characteristics of the SE2623L are
illustrated in Figure 3.
Signal pin assignments and functional pin descriptions are
described in Table 1. The absolute maximum ratings of the
SE2623L are provided in Table 2.
Table 1. SE2623L Signal Descriptions
Pin
Name
Description
1
RF_IN
RF input
2
EN
3
GND
4
Pin
Name
Description
9
GND
Ground
PA enable
10
RF_OUT
RF output
Ground
11
RF_OUT
RF output
VCC0
Power supply for bias circuit
12
GND
Ground
5
GND
Ground
13
VCC2
Power supply for second stage
6
GND
Ground
14
NC
No Connect—may be left floating or grounded
7
DET
Power detector output
15
VCC1
Power supply driver stages
8
NC
No Connect—may be left floating or grounded
16
GND
Ground
Table 2. SE2623L Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Minimum
Maximum
Units
Supply voltage
VCC0, VCC1, VCC2, RF_OUT
–0.3
+5.5
V
DC input on EN
VIN
–0.3
RF input power—RF out terminated in 50 Ω
PIN
Operating temperature range
TA
Junction temperature
TJ
Storage temperature range
TSTG
Electrostatic discharge:
ESD
–40
–40
Human Body Model (HBM), Class 1C (all pins)
+3.6
V
+12.0
dBm
+85
°C
+150
°C
+150
°C
1000
V
Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Table 3. SE2623L Recommended Operating Conditions
Minimum
Typical
Maximum
Units
Ambient temperature
Parameter
TA
Symbol
–40
+25
+85
°C
Supply voltage, relative to GND = 0 V
VCC
4.5
5.0
5.5
V
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2
February 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202397E
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
Table 4. SE2623L Electrical Specifications: DC Characteristics (Note 1)
(VCC = 5 V, EN = VENH, TA = 25 C as Measured on the Evaluation Board (De-embedded to the Device), All Unused Ports are Terminated
with 50 Ω, Unless Otherwise Noted)
Parameter
Supply current—Sum of all VCCs
Supply current
Symbol
Test Condition
Typical
Maximum
Units
ICC-802.11b
POUT = +29 dBm, 11 Mbps CCK signal, BT = 0.45,
VCC = 5.0 V
Minimum
600
700
mA
ICC-802.11g
POUT = +26 dBm, 54 Mbps OFDM signal, 64 QAM,
VCC = 5V
480
535
mA
ICQ
No RF
320
ICC
VEN = 0 V, No RF
mA
100
μA
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Table 5. SE2623L Electrical Specifications: AC Characteristics—802.11g/n/ac Transmit Characteristics (Note 1)
(VCC = 5.0 V, EN = 3.3 V, TA = 25 C as Measured on the Evaluation Board (De-embedded to the Device), All Unused Ports are Terminated
with 50 Ω, Unless Otherwise Noted)
Parameter
Frequency range
Symbol
Test Condition
fL-U
Minimum
MCS8, HT40, 1.8% EVM
+21
MCS8, HT40, 1.25% EVM
Output power
POUT
+23
dBm
dBm
+26
dBm
CCK signal, BT = 0.045, mask
+28
+29
dBm
MCS0, HT20, mask
+28
+29
dBm
MCS0, HT40, mask
+27
+28
dBm
No modulation
+29
+31
dBm
10
15
dB
30
33
dB
1
dB
|S11|
Small signal gain
|S21|
PIN = –25 dBm
Gain variation over band
S21
PIN = –25 dBm, fIN = 2400 to 2500 MHz
Rise and fall time
MHz
+18
Input return loss
2f
Units
2500
+24
OP1dB
3f
Maximum
MCS7, HT20, 3% EVM
+1 dB output compression point
Harmonics
Typical
2400
POUT = 29 dBm, 802.11b, 1 Mbps
tR, tF
Stability
STAB
CW, POUT = +29 dBm, 0.1 GHz to 20 GHz,
Load VSWR = 4:1
Ruggedness
RU
CW, 50% duty cycle, PIN = +12 dBm, Load VSWR = 6:1
–50
–45
–50
–45
dBm/
MHz
0.50
0.75
μs
All non-harmonically related outputs
< –42 dBm/MHz
No damage
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202397E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 27, 2014
3
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
Table 6. SE2623L Electrical Specifications: Logic Characteristics (Note 1)
(VCC = 5 V, EN = VENH, TA = 25 C as Measured on the Evaluation Board (De-embedded to the Device), All Unused Ports are Terminated
with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Minimum
Typical
Maximum
Units
3.6
0.4
V
250
20
μA
Logic voltage:
High (module on)
Low (module off)
VENH
VENL
1.8
0
Input current logic voltage:
High
Low
Enable pin input impedance
IENH
IENL
VEN = 0.4 V
1
ZEN
Passive pull-down
20
kΩ
Table 7. SE2623L Electrical Specifications: Power Detector Characteristics (Note 1)
(VCC = 5 V, EN = VENH, TA = 25 C as Measured on the Evaluation Board, Unless Otherwise Noted)
Parameter
Symbol
Frequency range
Test Condition
Minimum
f
Typical
Maximum
Units
2500
MHz
+30
dBm
2400
Power detect range
PDR
DC source impedance on DET
PDZSRC
2.0
kΩ
DC load impedance
PDZLOAD
26.5
kΩ
Output voltage
Power detect low-pass filter, –3 dB corner frequency
CW, measured at RF_OUT
PDVDC
PDVP5
PDVP26
PDVP29
Measured into 26.5 kΩ:
No RF
POUT = +5 dBm CW
POUT = +26 dBm CW
POUT = +29 dBm CW
LPF–3DB
Measured into 26.5 kΩ
+5
0.150
0.400
0.700
0.950
0.120
0.300
0.575
0.900
0.200
0.500
0.875
1.100
2
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Typical Performance Characteristics
1.1
1.0
0.9
DET (V)
0.8
0.7
0.6
0.5
0.4
2400 MHz, 5 V
2500 MHz, 5 V
0.3
0.2
0.1
+3
+5
+7
+9
+11
+13
+15
+17
+19
+21
+23
+25
+27
+29
Output Power (dBm)
Figure 3. SE2623L Detector Characteristics
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
4
February 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202397E
V
MHz
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
Evaluation Board Description
Evaluation Board Test Procedure
The SE2623L-EK1 Evaluation Board is used to test the
performance of the SE2623L-R PA. A typical application
schematic diagram is provided in Figure 4. Table 8 provides the
Bill of Materials (BOM) list for Evaluation Board components. A
photograph of the Evaluation Board is shown in Figure 5.
1. Connect GND to all ground pins.
2. Connect a power supply to the VCC1, VCC2, and the two
RF_OUT pins.
3. If desired, connect a voltage meter to the VDET pin.
4. Connect a +3.3 V supply to EN pin.
Circuit Design Considerations
The following design considerations are general in nature and
must be followed regardless of final use or configuration:
5. Connect a signal generator to the RF signal input port. Set it to
the desired RF frequency at a power level of –30 dBm or less
to the Evaluation Board. DO NOT enable the RF signal.

Paths to ground should be made as short as possible.
6. Connect a spectrum analyzer to the RF signal output port.

The ground pad of the SE2623L-R1 has special electrical and
thermal grounding requirements. This pad is the main
thermal conduit for heat dissipation. Since the circuit board
acts as the heat sink, it must shunt as much heat as possible
from the device.
Therefore, design the connection to the ground pad to
dissipate the maximum wattage produced by the circuit
board. Multiple vias to the grounding layer are required.
For further information, refer to the Skyworks Application
Note, PCB Design Guidelines for High Power Dissipation
Packages, document number 201211.


Bypass capacitors should be used on the DC supply lines. An
RF inductor is required on the VCC supply line to block RF
signals from the DC supply. Refer to the schematic drawing
in Figure 4 for further details.
The RF lines should be well separated from each other with
solid ground in between traces to maximize input-to-output
isolation.
7. Enable the power supply.
8. Enable the RF signal.
9. Take measurements.
CAUTION: If the input signal exceeds the rated power, the
Evaluation Board can be permanently damaged.
NOTE: It is important to adjust the VCC voltage source so that the
target supply voltage (+5) is measured at the board. The
high collector currents will drop the collector voltage
significantly if long leads are used. Adjust the bias voltage
to compensate.
Package Dimensions
Typical part markings for the SE2623L are shown in Figure 6. The
PCB layout footprint for the SE2623L is provided in Figure 7.
Package dimensions for the 16-pin QFN are shown in Figure 8,
and tape and reel dimensions are provided in Figure 9.
Package and Handling Information
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
The SE2623L is rated to Moisture Sensitivity Level 3 (MSL3) at
260 C, and can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
Solder Reflow Information (Document Number 200164).
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202397E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 27, 2014
5
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
J3
VCC0
R3
DNI
R6
DNI
R8
0Ω
4
5
6
7
VCC3
3
VCC1
VCC2
2
VCC0
1
R4
0Ω
C4
4.7 μF
R5
0Ω
R9
36 Ω
C10
DNI
C14
100 nF
R2
150 Ω
C5
470 nF
C7
100 nF
C9
DNI
C15
DNI
17
Pad
1
2
3
4
EN
RF_IN
EN
GND
VCC0
GND
RF_OUT
RF_OUT
GND
GND
GND
VDET
GND
C43
100 pF
GND
VCC1
GND
VCC2
J1
SMA
C8
DNI
16 15 14 13
VCC0
12
11
10
9
C1
3.3 pF
R1
0Ω
C2
2.4 pF
C6
15 pF
L1
1.0 nH
C3
2.4 pF
J2
SMA
C13
1.5 pF
5 6 7 8
C12
100 nF
R7
26.1K
EN
CLK
DATA
BP1
BP2
C11
DNI
1
2
3
4
5
6
7
J4
Y0742
Figure 4. SE2623L Evaluation Board Schematic Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
6
February 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202397E
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
Table 8. SE2623L Evaluation Board Bill of Materials
Quantity
1
Component
R1
Value
0Ω
Manufacturer
Panasonic
Mfr Part Number
ERJ3GEJ0R0
Package
0603
Description
Thick film chip resistor
1
L1
1.0 nH
Murata
LQG15HN1N0S02D
0402
1
C13
1.5 pF
Murata
GRM1555C1H1R5CZ01
0402
1
C1
3.3 pF
Murata
GRM1555C1H3R3CZ01
0402
Multilayer ceramic
1
C4
4.7 uF
Murata
GRM188R60J475KE19
0603
Multilayer ceramic
1
C6
15 pF
Murata
GRM1555C1H150JZ01
0402
Multilayer ceramic
1
R7
26.1K
Panasonic
ERJ2RKF2612
0402
Thick film chip resistor
1
R9
36 Ω
Panasonic
ERJ3GEYJ360
0603
Thick film chip resistor
1
C43
100 pF
Murata
GRM1555C1H101JZ01
0402
Multilayer ceramic
Multilayer ceramic
1
R2
150 Ω
Panasonic
ERJ3GEYJ151
0603
Thick film chip resistor
1
C5
470 nF
Murata
GRM155R60J474KE19
0402
Multilayer ceramic
QFN 300 X 300
1
U1
SE2623L
Skyworks Solutions
SE2623L
1
PCB1
Z464-B
Skyworks Solutions
Z464-B
2
C2, C3
2.4 pF
Murata
GRM1555C1H2R4CZ01
2
J3, J4
7X1
Samtec
TSW-107-07-G-S
2
R3, R6
DNI
2
J1, J2
SMA
Johnson Components
2
BP1, BP2
Value
3
R4, R5, R8
3
5
802.11g/n High Power PA
PCB
0402
Multilayer ceramic
100 mil
100 mil header
0402
Do Not Install
142-0701-851
end launch
SMA end launch straight
jack receptacle - tab
contact
Skyworks Solutions
printed element
0.25mm X 0.25mm
Bonding pad
0Ω
Panasonic
ERJ2GEJ0R0
0402
Thick film chip resistor
C7, C12, C14
100 nF
Murata
GRM155R61A104KA01
0402
Multilayer ceramic
C8, C9, C10, C11, C15
DNI
-
-
0402
-
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202397E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 27, 2014
7
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
Y0743
Figure 5. SE2623L Evaluation Board
Pin 1
Indicator
SiGe
2623L
XXXXX
Part Number
Lot Code
SKY
2623L
XXXXX
Y0744
Figure 6. SE2623L Typical Part Markings
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8
February 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202397E
16
15
13
1.40
1.59
1.29
0.078
0.94
14
3X 0.64
3.40
0.95
0
3X 0.64
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
14
16
1.61
1.24
0.16 Typ.
1
12
2
11
11
0.483 3.40
6X 0.25
3
10
4
9
12
3X 0.64
0.500 Typ.
0
0
3
10
3X 0.64
9
1.35
8
6
14X ø0.25
Board Metal
Via Pattern
(Note 1)
3.40
3.50
0.65 Typ.
1.70
16
8
0
5
0.15 Typ.
R0.15
Typ.
1.50
0.60 Typ.
7
6
1.27
5
1.35
15
14
Component
Outline
13
15
0.20 Typ.
14
13
1
12
1
16
0.65 Typ.
2
11
2
3.40
0.20 Typ.
3.50 1.70
3
10
3
4
9
4
0.70 Typ.
0.500 Typ.
0.35 Typ.
Solder Mask Pattern
(Note 2)
0.60 Typ.
0.500 Typ.
0.25 Typ.
58% solder coverage
on center pad
Stencil Pattern
(Note 3)
Notes:
1. Via hole recommendations:
0.025 mm Cu via wall plating (minimum), via holes to be plated shut or plugged and
capped, both sides.
2. Solder mask recommendations:
Contact board fabricator for recommended solder mask offset and tolerance.
3. Stencil recommendations:
0.125 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer
better paste release.
4. Dimensions and tolerances according to ASME Y14.5M-1994.
5. Unless specified, dimensions are symmetrical about center lines.
6. All dimensions are in millimeters.
S3376
Figure 7. SE2623L PCB Layout Footprint
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202397E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 27, 2014
9
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
1.700 ± 0.050
3.000 ± 0.050
0.10 C
–B–
–A–
0.850 ± 0.050
See Note 3
16
15
14
O.30 x 45°
0.203 Ref.
13
13
12
1
11
2
3.000 ± 0.050
3
10
4
9
14
15
16
1
12
1.700 ± 0.050
2X
R0.075
Typ.
11
2
0.500
10
3
9
4
Seating Plane
2X
5
0.10 C
6
7
8
8
0.10 C
7
6
5
16X 0.230 ± 0.050
0.000 to 0.050
0.10 M C A B
0.05 M C
–C–
16X 0.375 ± 0.050
Bottom Side
Top Side
Notes:
1. All measurements are in millimeters.
2. Dimensions and tolerances according to ASME Y14.5M-1994.
Unless otherwise specified, the following values apply:
Decimal Tolerance:
Angular Tolerance:
X.X (1 place) ± 0.1 mm
±1°
X.XX (2 places) ± 0.05 mm
X.XXX (3 places) ± 0.025 mm
3. Terminal #1 identification mark located within marked area.
4. Unless specified, dimensions are symmetrical about center lines.
S3374
Figure 8. SE2623L 16-Pin QFN Package Dimensions
ø1.00 Min.
0.30 ± 0.05
2.00 ± 0.05)
(See Note 1)
4.00 ± 0.1
(See Note 2)
ø1.55 ± 0.05
1.75 ± 0.1
C
L
A
1.10 ± 0.10
A
R0.1 Typ.
8.00 ± 0.10
3.30 ± 0.05
Pin 1
Indicator
Notes:
1. Measured from centerline of sprocket hole to centerline of pocket.
2. Cumulative tolerance of 10 sprocket holes: ±0.02 mm.
3. All measurements are in millimeters.
S3377
Figure 9. SE2623L 16-Pin QFN Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
10
12.00 ± 0.10
3.30 ± 0.05
5.50 ± 0.10
(See Note 1)
A
February 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202397E
DATA SHEET • SE2623L: 2.4 GHZ HIGH POWER WIRELESS LAN POWER AMPLIFIER
Ordering Information
Model Name
SE2623L 2.4 GHz High Power Wireless LAN PA
Manufacturing Part Number
SE2623L
Evaluation Board Part Number
SE2623L-EK1
Copyright © 2012-2014 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands
and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com,
are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202397E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 27, 2014
11