Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
CPS
CTX
CSD
ANT_SEL
SE2431L: 2.4 GHz Front-End Module
Applications
 Smart meters
 In-home appliances
Logic
Control
 Smart thermostats
PA
Features
ANT1
 Integrated:
– PA with up to +24 dBm output power
– LNA with programmable bypass
– Antenna switching with Tx and Rx diversity function
TR
ANT2
 Suitable for Zigbee , Bluetooth Low Energy, and Bluetooth 1.0
®
®
LNA
 Typical low NF: 2 dB
Y1934
 Operating temperature range: –40 °C to +125 °C
Figure 1. SE2431L Block Diagram
 Single-ended 50 Ω Tx/Rx RF interface
 Fast switch on/off time <1 μs
 Supply operation: 2.0 V to 3.6 V
 Sleep mode current: 0.05 μA typical
 Small QFN (24-pin, 3.0 mm x 4.0 mm x 0.9 mm NickelPalladium-gold [NiPdAu] plated) package
(MSL1, 260°C per JEDEC J-STD-020)
Skyworks GreenTM products are compliant with
all applicable legislation and are halogen-free.
For additional information, refer to Skyworks
Definition of GreenTM, document number
SQ04–0074.
Description
The SE2431L is a high-performance, fully integrated RF front-end
module (FEM), suitable for Zigbee, Bluetooth Low Energy, and
Bluetooth 1.0 applications.
The SE2431L is designed for ease of use and maximum flexibility,
with fully matched 50 Ω input and output, integrated inter-stage
matching and harmonic filter, and digital controls that are
compatible with 1.6 V to 3.6 V Complementary Metal Oxide
Semiconductor (CMOS) levels.
The RF blocks operate over a wide supply voltage range from
2.0 V to 3.6 V, which allows the SE2431L to be used in batterypowered applications over a wide spectrum of the battery
discharge curve.
A functional block diagram is shown in Figure 1. The pin
configuration and package are shown in Figure 2. Signal pin
assignments and functional pin descriptions are provided in
Table 1.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015
1
CTX
BOUT
VCC1
CPS
CSD
24
23
22
21
20
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
B1
2
18
GND
N/C
3
17
N/C
N/C
4
16
ANT_SEL
N/C
5
15
ANT1
T/R
6
14
GND
N/C
7
13
ANT2
12
GND
GND
GND
GND
N/C
11
VCC2
10
19
9
1
8
B2
Y0587
Figure 2. SE2431L Pinout
(Top View)
Table 1. SE2431L Signal Descriptions
Pin
Name
1
B2
2
B1
3
Description
Pin
Name
Description
Connect through the bias resistor to pin 23
13
ANT2
Connect to 50 Ω antenna
Connect through the bias resistor to pin 23
14
GND
Connect to PCB ground
N/C
Not connected internally to the device
15
ANT1
Connect to 50 Ω antenna
4
N/C
Not connected internally to the device
16
ANT_SEL
5
N/C
Not connected internally to the device
17
N/C
Not connected internally to the device
6
T/R
Transmit/receive port from/to transceiver,
single-ended 50 Ω
18
GND
Connect to PCB ground
7
N/C
Not connected internally to the device
19
VCC2
Connect to positive supply
8
N/C
Not connected internally to the device
20
CSD
Connect to the GPIO signal to control the SE2431L modes (see
Table 8)
9
GND
Connect to PCB ground
21
CPS
Connect to the GPIO signal to control the SE2431L modes (see
Table 8)
10
GND
Connect to PCB ground
22
VCC1
Connect to positive supply.
11
GND
Connect to PCB ground
23
BOUT
Connect to pins 1 and 2 through the bias resistors
12
GND
Connect to PCB ground
24
CTX
Connect to the GPIO signal to control the antenna switch (see
Table 8)
Connect to the GPIO signal to control the SE2431L modes (see
Table 8)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2
June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
Electrical and Mechanical Specifications
The absolute maximum ratings of the SE2431L are provided in
Table 2. The recommended operating conditions are specified in
Table 3, and electrical specifications are provided in Tables 4
through 7.
The state of the SE2431L is determined by the logic provided in
Table 8.
Table 2. SE2431L Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Minimum
Maximum
Units
Supply voltage 1
VCC1
–0.3
3.6
V
Supply voltage 2
VCC2
–0.3
3.6
V
–0.3
3.6
V
Control pin voltages
Operating temperature
TOP
–40
+125
C
Storage temperature
TSTG
–40
+125
C
Tx output power at ANT1 or ANT2 port into 50 Ω load
POUT_TX_MAX
+24
dBm
Tx input power at TR port
PIN_TX_MAX
+6
dBm
Rx input power at ANT1 or ANT2 ports
PIN_RX_MAX
+10
dBm
Rx input power at ANT1 or ANT2 ports in bypass mode
PIN_RX_BYPASS_MAX
+15
dBm
Thermal resistance
ΘJC
40
C/W
Electrostatic discharge:
ESD
1000
V
Human Body Model (HBM), Class 1C
Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Table 3. Recommended Operating Conditions
Parameter
Symbol
Minimum
Typical
Maximum
Units
Ambient temperature
TA
–40
+25
+125
C
Supply voltage on VCC pins
VCC1
2.0
3.0
3.6
V
Supply voltage on VCC pins
VCC2
2.0
3.0
3.6
V
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015
3
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
Table 4. SE2431L Electrical Specifications: DC (Note 1)
(VCC = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
Total supply current
ICC_TX20
Tx mode POUT = +20 dBm
115
mA
Total supply current
ICC_TX17
Tx mode POUT = +17 dBm
90
mA
Total supply current
ICC_TX10
Tx mode POUT = +10 dBm
50
mA
Quiescent current
ICQ_TX
No RF
30
mA
Total supply current
ICC_RX
Rx mode
5
Total supply current
ICC_RXBYPASS
Rx Bypass mode
Sleep supply current
ICC_OFF
No RF
0.05
7
mA
300
μA
1.0
μA
Note 1: Performance is guaranteed only under the conditions listed in the above table.
Table 5. SE2431L Electrical Specifications: Logic Characteristics (Note 1)
(VCC = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], Unless Otherwise Noted)
Max
Units
Logic input high voltage
Parameter
VIH
Symbol
Test Condition
Min
1.6
Typical
3.6
V
Logic input low voltage
VIL
0
0.3
V
Logic input high current
IIH
1
μA
Logic input low current
IIL
1
μA
Note 1: Performance is guaranteed only under the conditions listed in the above table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
4
June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
Table 6. SE2431L Electrical Specifications: AC Characteristics (Note 1)
(VCC = 3 V, TA = +25 C, as Measured on Skyworks SE2431L-EK1 Evaluation Board [De-Embedded to the Device], All Unused Ports
Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
2483
MHz
Transmit (Tx)
Frequency range
fIN
2400
Output power at ANT1 or ANT2 ports (Notes 2, 3)
POUT
VCC = +3.6 V, PIN = +3 dBm
VCC = +3.3 V, PIN = 0 dBm
VCC = +3.0 V, PIN = 0 dBm
VCC = +2.7 V, PIN = 0 dBm
VCC = +2.0 V, PIN = 0 dBm
VCC = +3.0 V, PIN = –13 dBm
Small signal gain
S21
2400 MHz to 2483 MHz
Small signal gain variation (Note 2)
ΔS21
Gain variation across channels
2400 to 2483 MHz
Harmonics (Notes 2, 4)
HD2, HD3
POUT = +20 dBm
Output return loss (Note 2)
S22_ANT
At ANT1 or ANT2 ports
Input return loss (Note 2)
S11
At TR port, Tx mode
Rise and fall times
tR (Note 6)
tF (Note 7)
Stability
STAB
CW, PIN = 0 dBm
0.1 GHz to 20.0 GHz
Load VSWR = 6:1
Ruggedness
RU
CW, PIN = +6 dBm, Load VSWR = 10:1
dBm
dBm
dBm
dBm
dBm
dBm
+24.0
+22.5
+21.0
+20.5
+17.0
+10
19
22
–10
25
dB
1
dBp-p
–42
dBm/MHz
–5
dB
–5
dB
800
ns
All non-harmonically related outputs
<–42.0 dBm/MHz
No permanent damage
Receive (Rx)
Frequency range
fIN
2400
Receive gain (Note 2)
Rx_GAIN
10.0
Receive noise figure (Note 2)
NF
Third order input intercept point (Note 2)
IIP3
–3
+2
dBm
LNA input compression point (Note 2)
IP1dB
–13
–8
dBm
Antenna port return loss (Note 2)
S11_ANT
Output return loss (Note 2)
S22
Rise and fall times
tR (Note 5)
tF (Note 6)
Bypass gain
G_BP
–3
Tx or Rx Bypass 1 dB input compression point
IP1dB
+15
At TR port, Rx mode
2483
MHz
12.5
15.0
dB
2.0
2.5
dB
–10
–5
dB
–10
–5
dB
800
ns
–2
dB
dBm
Note 1: Performance is guaranteed only under the conditions listed in the above table.
Note 2: 2400 MHz to 2483 MHz.
Note 3: Offset EVM = 1% typical.
Note 4: IEEE 802.15.4 source.
Note 5: From 50% of the CTX edge to 90% of the final RF output power.
Note 6: From 50% of the CTX edge to 10% of the final RF output power.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015
5
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
Table 7. SE2431L Electrical Specifications: AC Characteristics, Diversity Antenna Function (Note 1)
(VCC1 = VCC2 = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], All Unused Ports Terminated with
50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Min
Typical
Max
Units
Isolation between ANT1 and ANT2 ports
ISOLANTSW
–20
dB
Antenna 1 to antenna 2 switching time
tANT1-ANT2
400
ns
Note 1: Performance is guaranteed only under the conditions listed in the above table. Unused antenna port should be connected to 50 Ω.
Table 8. SE2431L Logic Controls (Note 1)
(VCC = 3 V, TA = +25 C, Unless Otherwise Noted)
Mode
CPS
CSD
CTX
ANT_SEL
All off (sleep mode) (Note 2)
0
0
0
X
1
Rx or Tx bypass mode
0
1
0
X
2
Rx LNA mode
1
1
0
X
3
Tx mode
X
1
1
X
ANT1 port enabled
X
1
X
0
ANT2 port enabled
X
1
X
1
0
Description
Note 1: The logic 0 and 1 levels are compliant to VIL and VIH, respectively, as specified in Table 5.
Note 2: All controls must be at logic 0 to achieve the specified sleep current.
Evaluation Board Description
Measure TX Performance
The SE2431L Evaluation Board is used to test the performance of
the SE2431L front-end module (FEM). An Evaluation Board
schematic diagram is provided in Figure 3. A reference design
schematic is shown in Figure 4. A photograph of the Evaluation
Board is shown in Figure 5. A Bill of Materials (BOM) for the
Evaluation Board is provided in Table 9.
Apply an RF signal to connector J34 (TR) to monitor the 2.4 GHz
amplifier performance. Monitor the output power on connector
J35 (ANT1) or J32 (ANT2).
Evaluation Board Setup Procedure
Connect Supply
1. Connect J32, J34, and J35 to 50 Ω instruments. Terminate all
unused ports (if applicable) with 50 Ω.
2. Connect the supply ground to Pin 20 of the J36 header.
Measure RX Performance
Apply an RF signal to connector J35 (ANT1) or J32 (ANT2) to
monitor the 2.4 GHz LNA performance. Monitor the output signal
on connector J34 (TR).
CAUTION: Care should be taken not to overdrive the amplifier by
applying too much RF on the input to the device. A
suitable starting input power for the device is
–20 dBm.
3. Connect 3.0 V to Pins 1, 3, and 16 of J36.
4. Refer to Table 8 for information about selecting the required RF
path and for antenna port control.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
6
June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
J36
1
3
5
7
9
11
13
15
17
19
VCC
VDD
C1
2.2 uF
C2
2.2 uF
VCC
2
4
6
8
10
12
14
16
18
20
VCC
VDD
CTX
CPS
CSD
VCC2
ANT_SEL
CPS
C4
10 pF
CSD
R5
100 kΩ
R6
100 kΩ
CTX
VCC2
R3
100 kΩ
C3
100 nF
PAD
R1
2.2 kΩ
CTX
BOUT
VCC1
CPS
CSD
25
BOUT
24
23
22
21
20
BOUT
1
2
3
4
5
6
7
R2
1.2 kΩ
VCC2
GND
SE2431L
DNC
U1
ANT_SEL
ANT1
GND
ANT2
19
18
17
16
15
14
13
C5
10 pF
ANT_SEL
R4
100 kΩ
8
9
10
11
12
DNC
GND
GND
GND
GND
J34
SMA
B2
B1
DNC
DNC
DNC
T/R
DNC
J35
SMA
TP1
Test Point
J32
SMA
Y2127
Figure 3. SE2431L Evaluation Board Schematic
VCC
C1
2.2 uF
VCC
C3
10 pF
CTX
C2
100 nF
CPS
CSD
T/R
6
20
21
CPS
23
22
VCC1
CSD
DNC
DNC
ANT_SEL
DNC
ANT1
T/R
GND
DNC
ANT2
8
DNC
7
GND
SE2431L
U1
DNC
19
18
17
16
ANT_SEL
15
ANT1
14
13
11
GND
12
GND
5
B1
GND
4
VCC2
10
3
R2
1.2 kΩ
C4
10 pF
B2
GND
2
9
1
CTX
PAD
R1
2.2 kΩ
BOUT
25
BOUT
24
BOUT
TP1
Test Point
ANT2
Y2128
Figure 4. SE2431L Reference Design Schematic
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015
7
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
Figure 4. SE2431L Evaluation Board
Notes to Figure 4:
1. R44, R45, R43, R47, and C52 are for evaluation purposes and can be removed in the final application.
2. The Skyworks Evaluation Board contains 0 Ω resistors and footprints for non-populated components that are not shown in the
schematic.
Table 9. SE2431L Bill of Materials (BOM)
Component
Value
Manufacturer
Mfr Part Number
Package Size
Description
2.2 μF
Murata
GRM21BR71A225KA01L
C3
100 nF
Murata
GRM155R71C104KA88D
0402
Monolithic ceramic capacitor
C4, C5
10 pF
Murata
GRM1555C1H100JZ01
0402
Multilayer ceramic capacitor
J32, J34, J35
SMA
Johnson Components
142-0701-851
End launch
SMA end launch straight jack receptacle – tab
contact
J36
10 x 2
Samtec
TSW-110-07-G-D
100 mil
100 mil header
R1
2.2 k Ω
Panasonic
ERJ2GEJ222
0402
Thick film chip resistor
R2
1.2 k Ω
Panasonic
ERJ2GEJ122
0402
Thick film chip resistor
R3, R4, R5, R6
100 k Ω
Panasonic
ERJ2GEJ104
0402
Thick film chip resistor
TP1
Test Point
Skyworks Solutions
Printed element
0.635 mm test point TH
TH 0.635 test point
U1
SE2431L
Skyworks Solutions
SE2431L
QFN400X300
Front-end module
C1, C2
0805
Ceramic capacitor, 2.2 μF, 10%, X7R, 10 V
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8
June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
Package Dimensions
Package and Handling Information
The PCB layout footprint for the SE2431L is provided in Figure 5.
A typical part marking diagram is shown in Figure 6. Package
dimensions are shown in Figure 7, and tape and reel dimensions
are provided in Figure 8.
Instructions on the shipping container label regarding exposure to
moisture after the container seal is broken must be followed.
Otherwise, problems related to moisture absorption may occur
when the part is subjected to high temperatures during solder
assembly.
The SE2431L is rated to Moisture Sensitivity Level 1 (MSL1) at
260 °C, and can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
Solder Reflow Information, document number 200164.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015
9
3X 1.05
3X 0.52
0
3X 1.05
4.40
2.70
3X 0.52
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
5X 0.54
3.40
1.70
0
0
5X 0.54
0
0.60 Typ
0.20 Typ
15X ø0.254
0.400 Typ
Via Pattern
(Note 4)
Board Metal
4.40
4.50
1.03
Typ
2.50
0.20 Typ
0.53 Typ
3.40
3.50
1.50
0.20 Typ
0.60 Typ
0.70 Typ
0.30 Typ
0.400 Typ
Package
Outline
0.20 Typ
0.400 Typ
Stencil Pattern
(Note 5)
57% Solder Coverage
on Center Pad
Solder Mask Pattern
(Note 6)
Notes:
1. All dimensions are in millimeters.
2. Dimensions and tolerances per ASME 14.5M–1994.
3. Unless specified, dimensions are symmetrical about center lines.
4. Via hole recommendations:
0.025 mm Cu via wall plating (minimum), via holes to be filled with conductive paste and plated over.
5. Stencil recommendations:
0.10 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release.
6. Solder mask recommendations:
Contact board fabricator for recommended solder mask offset and tolerance.
Figure 5. PCB Layout Footprint
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
10
June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J
Y2123
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
Terminal
Finish Symbol
Pin 1
Indicator
Skyworks
Part Number
Lot Code
Y2124
Figure 6. SE2431L Typical Part Marking
3.00 ± 0.05
A
1.60 ± 0.05
0.85 ± 0.05
0.05 C
0.203 Ref
B
0.30 x 45°
0.00–0.050
Pin 1
Indicator
Pin 1
Indicator
Exposed Pad
4.00 ± 0.05
2.60 ± 0.05
0.40
R0.075, Typ
24 X 0.25 Min
2X
0.05 C
25X
0.05 C
Top View
0.05 C
4
C
See Detail A
See Detail B
Bottom View
Seating
Plane
2X
Detail B
Scale 2X
4 Places
Side View
0.12 ± 0.05
2X R0.075
Notes:
0.40 ± 0.05
1. Dimensions are in millimeters.
2. Dimensions and tolerances according to ASME Y14.5M-1994.
3. Unless otherwise specified, the following values apply:
0.20 ± 0.05
Decimal Tolerance:
Angular Tolerance:
5
±1/2°
X.X (1 place) ± 0.1 mm
X.XX (2 places) ± 0.05 mm
X.XXX (3 places) ± 0.025 mm
4. Coplanarity applies to the terminals as well as all other bottom surface metallization.
5. Dimension applies to metallized terminal. If terminal tip has a radius, dimension
should not be measured in that radius area.
6. Unless specified, dimensions are symmetrical about center lines.
R0.075
Detail A
Scale 2X
20 Places
0.07
0.05
C A B
C
0.28 ± 0.05
0.20 ± 0.05
5
0.07
0.05
0.40 ± 0.05
C A B
C
Y2122
Figure 7. SE2431L Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015
11
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
8.00
∅1.5 +0.1/–0.0
4.00 (Note 1)
1.75 ± 0.10
∅1.50 Min.
A
5.50 ± 0.05
(Note 3)
R0.3 Max.
4.40
12.0 ± 0.30
2.00 ± 0.05 (Note 3)
0.30 ± 0.05
A
0.12
1.10
Pin 1 Indicator
3.40
A
Notes:
1. 10 sprocket hole pitch cumulative tolerance ±0.2.
2. Camber in compliance with EIA 481.
3. Pocket position relative to sprocket hole measured
as true position of pocket, not pocket hole.
4. All measurements are in millimeters.
0.12
R0.25
Figure 8. SE2431L-R Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
12
June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J
S2742
DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE
Ordering Information
Model Name
SE2431L: 2.4 GHz Front-End Module
Manufacturing Part Number
SE2431L
Evaluation Board Part Number
SE2431L-EK1
Copyright © 2012-2015 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for
identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by
reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015
13