Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
SKY65362-11: 900 to 930 MHz High-Power RF Front-End
Module
Applications
Description
 Smart meters
The SKY65362-11 is a high-performance, highly integrated RF
front-end module (FEM) designed for high-power Industrial,
Scientific, Medical (ISM) band applications operating in the 900 to
930 MHz frequency range.
 In-home appliances
 Smart thermostats
The FEM is designed for ease of use and maximum flexibility with
fully matched, 50 Ω power amplifier (PA) input and output, and
digital controls compatible with 1.6 to 3.3 V CMOS levels.
Features
 Integrated PA with +30.5 dBm output power
The RF blocks operate over a wide supply voltage range from
3.00 to 5.25 V that allows the SKY65362-11 to be used in battery
powered applications over a wide spectrum of the battery
discharge curve.
 Integrated LNA with programmable bypass
 Low FEM NF of 2.5 dB, typical
 Single-ended 50 Ω transmit/receive RF interface
The SKY65362-11 is packaged in a 36-pin, 6 x 6 mm Multi-Chip
Module (MCM), which allows for a highly manufacturable low-cost
solution.
 Supply voltage: 3.00 V to 5.25 V
 Sleep mode current: <1 μA
 Small MCM (36-pin, 6 x 6 mm) package
(MSL3, 260 C per JEDEC J-STD-020)
A functional block diagram of the SKY65362-11 is shown in
Figure 1. The 36-pin MCM package and pinout are shown in
Figure 2. Signal pin assignments and functional pin descriptions
are provided in Table 1.
CPS
ANT_SEL
PDETF
PDETR
IALARM
CTX
CSD
Skyworks GreenTM products are compliant with
all applicable legislation and are halogen-free.
For additional information, refer to Skyworks
Definition of GreenTM, document number
SQ04–0074.
Logic
control
TX
ANT1
2-Stage
GaAs PA
ANT2
Switch
RX
RX_FLT
LNA_IN
1-Stage
LNA
Y0205
Figure 1. SKY65362-11 FEM Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015
1
GND
VSUP1
VSUP2
VCC1
GND
VCC0
GND
VCC2
GND
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
36
35
34
33
32
31
30
29
28
GND
PDETR
4
24
GND
CSD
5
23
GND
CPS
6
22
GND
CTX
7
21
GND
IALARM
8
20
ANT_1
ANT_SEL
9
19
GND
10
11
12
13
14
15
16
17
18
ANT_2
PDETF
GND
GND
25
RX_FLT
26
3
GND
2
LNA_IN
GND
GND
GND
GND
27
GND
1
RX
PA_IN
Y0206
Figure 2. SKY65362-11 Pinout – 36-Pin MCM
(Top View)
Table 1. SKY65362-11 Signal Descriptions
Pin
Name
Description
Pin
Name
Description
1
PA_IN
PA input
19
GND
Ground
2
GND
Ground
20
ANT1
Antenna 1
3
PDETF
Forward power detector output
21
GND
Ground
4
PDETR
Reverse power detector output
22
GND
Ground
5
CSD
Standby control (see Table 9)
23
GND
Ground
6
CPS
Receive mode gain control (see Table 9)
24
GND
Ground
7
CTX
Transmit/receive control (see Table 9)
25
GND
Ground
8
IALARM
PA current alarm output (see Table 9)
26
GND
Ground
9
ANT_SEL
Antenna select control input (see Table 9)
27
GND
Ground
10
RX
Receive output
28
GND
Ground
11
GND
Ground
29
VCC2
PA voltage supply
12
GND
Ground
30
GND
Ground
13
GND
Ground
31
VCC0
Decoupling capacitor
14
LNA_IN
LNA input
32
GND
Ground
15
GND
Ground
33
VCC1
PA voltage supply
16
RX_FLT
Receive path after internal switches that connect
ANT1 and ANT2
34
VSUP2
FEM voltage supply
17
GND
Ground
35
VSUP1
FEM voltage supply
18
ANT2
Antenna 2. No integrated filtering.
36
GND
Ground
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2
January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
Electrical and Mechanical Specifications
Electrical specifications are provided in Tables 4 through 8. The
state of the SKY65362-11 is determined by the logic provided in
Table 9.
The absolute maximum ratings of the SKY65362-11 are provided
in Table 2. The recommended operating conditions are specified
in Table 3.
Table 2. SKY65362-11 Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Supply voltage (no RF)
VCC
Control pin (CSD, CPS, CTX, IALARM, and ANT_SEL) voltage
Minimum
Maximum
Units
–0.3
+6.0
V
–0.3
VCC (VCC < 5 V)
V
Operating temperature
TA
–40
+85
C
Storage temperature
TSTG
–40
+125
C
Transmit input power
PIN_TX_MAX
+10
dBm
Receive RF input power @ ANT1 or ANT2 ports
PIN_RX_MAX
+10
dBm
Voltage Standing Wave Ratio @ ANT1 or ANT2 ports
VSWR
10:1
–
Electrostatic discharge:
ESD
1000
V
Human Body Model (HBM), Class 1C
Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Table 3. SKY65362-11 Recommended Operating Conditions
Minimum
Typical
Maximum
Units
Supply voltage
Parameter
VCC
Symbol
4.75
5.00
5.25
V
Operating temperature
TA
–40
+25
+85
C
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015
3
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
Table 4. SKY65362-11 DC Electrical Specifications (Note 1)
(VCC = +5.0 V, TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
515
mA
ICC_TX27
ICC_TX24
POUT = +30.5 dBm
(Note 2)
POUT = +27 dBm
POUT = +24 dBm
300
230
mA
mA
Quiescent current, transmit mode
ICQ_TX
No RF
85
mA
Total supply current, receive mode
ICC_RX
6
mA
Total supply current, receive bypass mode
ICC_RXBYP
820
μA
Sleep supply current
ICC_OFF
Total supply current, transmit mode
ICC_TX30
No RF
0.05
1.00
μA
Note 1: Performance is guaranteed only under the conditions listed in this table.
Note 2: Typical current listed into VSWR = 1:1. ICC = 700 mA into VSWR = 2.5:1 guaranteed by characterization.
Table 5. SKY65362-11 Receive Mode Electrical Specifications (Note 1)
(VCC = +5.0 V, TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], All Unused Ports Terminated
with 50 Ω, Input Port = ANT1, Output Port = RX, Unless Otherwise Noted)
Parameter
Symbol
Frequency range
f
Gain
S21_RX
Test Condition
Min
Typical
900
Max
Units
930
MHz
900 to 930 MHz
16
dB
2.5
dB
Noise figure
NF
900 to 930 MHz
Third order input intercept point
IIP3
900 to 930 MHz,
–20 dBm/tone, 200 kHz tone
separation
–5
–2
dBm
–15
–12
dBm
1 dB Input compression point
IP1dB
900 to 930 MHz
Antenna port return loss
S11_RX
900 to 930 MHz, into
50 Ω, ANT1 or ANT2 port
–12
–6
dB
S22_RX
ANT1 terminated in 50 Ω
–12
–6
dB
Turn-on/off time
tON_RX,
tOFF_RX
Receive or receive bypass to
“off,” “off” to receive or
receive bypass, from 50% of
CTX edge to 10% of final RF
output power (Note 2)
Gain in receive bypass mode
S21_RXBYP
–4
1 dB Input compression point in receive
bypass mode
IP1dB_RXBYP
+10
Receive port return loss in receive or receive
bypass mode
11
–3
Note 1: Performance is guaranteed only under the conditions listed in this table.
Note 2: Not production tested. Guaranteed by characterization.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
4
January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B
μs
dB
dBm
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
Table 6. SKY65362-11 Transmit Mode Electrical Specifications (1 of 2) (Note 1)
(VCC = +5.0 V, TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], All Unused Ports Terminated
with 50 Ω, Input Port = PA_IN, Outport Port = ANT1, Unless Otherwise Noted)
Parameter
Symbol
Frequency range
f
Output power @ ANT1 port
POUT
Test Condition
Min
Typical
900
Max
Units
930
MHz
900 to 930 MHz with specified
matching network on EVB, CW,
PIN = 0 dBm:
dBm
dBm
dBm
+30.5
+28
+26
VCC = 5.0 V
VCC = 4.0 V
VCC = 3.6 V
PA power added efficiency
PAE
POUT = +30.5 dBm @ ANT1
port, 915 MHz
43
%
Input return loss
S11_TX
902 to 928 MHz
–10
dB
Small signal gain
S21_900
902 to 928 MHz
33
dB
Output return loss
S22_TX
900 to 930 MHz, into 50 Ω,
ANT1 and ANT2 ports
–10
dB
900 to 930 MHz with specified
matching network on EVB, CW,
POUT = +30.5 dBm @ ANT1 port
(Note 2)
–35
–30
dBc
900 to 930 MHz with specified
matching network on EVB, CW,
POUT = +30.5 dBm @ ANT1 port
(Note 2)
–50
–45
dBc
POUT = +30.5 dBm @ ANT1
port, resolution bandwidth =
100 kHz, CW (Note 3)
–55
–50
dBm
nd
th
th
rd
th
th
th
2 , 6 , 7 , and 10 harmonics (HD 2, 6, 7,
and 10)
th
th
3 , 4 , 5 , 8 , and 9 harmonic (HD 3, 4, 5,
8, and 9)
Non-harmonic spurious
2fo, 6fo, 7fo,
10fo
3fo, 4fo, 5fo,
8fo, 9fo
Spurious
Change in output power under VSWR
POUT_VSWR
VSWR = 2.5:1, CW, reference
POUT = +30.5 dBm into 50 Ω
(Note 3)
+1.5
dB
Turn-on/off time
tON_TX,
tOFF_TX
“Off” to transmit or transmit to
“off,” from 50% of CTX edge to
90% of final RF output power
(Note 3)
11
μs
Mode change time
tMODE_CHANGE
Transmit to receive or receive
bypass, receive or receive
bypass to transmit, from 50% of
CTX edge to 10% of final RF
output power (Note 3)
11
μs
–3
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015
5
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
Table 6. SKY65362-11 Transmit Mode Electrical Specifications (2 of 2) (Note 1)
(VCC = +5.0 V, TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], All Unused Ports Terminated
with 50 Ω, Input Port = PA_IN, Outport Port = ANT1, Unless Otherwise Noted)
Max
Units
Forward power detect
Parameter
PFWD
Up to VSWR = 2.5:1
0.35
1.2
V
Reverse power detect
PREV
Up to VSWR = 2.5:1
0.35
1.2
V
Power detector accuracy
PDET_ACC
VSWR = 2.5:1 (Note 3)
±1
dB
Current alarm trigger output
IALARM
Low if ICC < 800 mA,
High if ICC > 800 mA (Note 4)
800
mA
Stability
STAB
CW, POUT = +30.5 dBm into
50 Ω, 0.1 to 20 GHz,
load VSWR = 6:1 (Note 3)
All non-harmonically related outputs < –43 dBm
CW, POUT = +30.5 dBm into
50 Ω load, VSWR = 10:1 (Note 3)
No permanent damage
Ruggedness
Symbol
RUG
Test Condition
Min
Typical
Note 1: Performance is guaranteed only under the conditions listed in this table.
Note 2: Harmonics above 5th are not production tested. Guaranteed by characterization.
Note 3: Not production tested. Guaranteed by characterization.
Note 4: Current Alarm trigger point is adjustable by external components R2, R3, R4, R5 in Figure 3. Contact Sales support for further information.
Table 7. SKY65362-11 Diversity Antenna Electrical Specifications (Note 1)
(VCC = +5.0 V, TA = +25 C, f = 900 MHz to 930 MHz, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], All
Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
Isolation between ANT1 and ANT2 ports
ISOL_ANT1/2
–20
dB
ANT1 to ANT2 switching time, transmit mode
tANT1-ANT2_TX
(Note 2)
1
μs
ANT1 to ANT2 switching time, receive mode
tANT1-ANT2_RX
(Note 2)
1
μs
Note 1: Performance is guaranteed only under the conditions listed in this table.
Note 2: Not production tested. Guaranteed by characterization.
Table 8. SKY65362-11 Electrical Specifications: Control Logic Characteristics (Note 1)
(TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Control voltage:
High
Low
VIH
VIL
(Note 2)
Input current:
High
Low
IIH
IIL
(Note 2)
Current alarm output voltage
VOH
VCC = 5 V
Min
Typical
1.6
0
Max
Units
3.6
0.3
V
V
1
1
μA
μA
3.3
Note 1: Performance is guaranteed only under the conditions listed in this table.
Note 2: Not production tested. Guaranteed by characterization.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
6
January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B
V
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
Table 9. SKY65362-11 Mode Control Logic (Note 1)
CPS
(Pin 6)
CSD
(Pin 5)
CTX
(Pin 7)
ANT_SEL
(Pin 9)
Sleep (all off)
0
0
0
X
Receive bypass
0
1
0
X
Receive LNA mode
1
1
0
X
Transmit
X
1
1
X
ANT1 port enabled
X
X
X
0
ANT2 port enabled
X
X
X
1
Mode
Note 1: “1” = 1.6 to 3.6 V, “0” = 0 to 0.3 V, “X” = don’t care.
Evaluation Board Description
Package and Handling Information
The SKY65362-11 Evaluation Board is used to test the
performance of the SKY65362-11 FEM. An Evaluation Board
schematic diagram is provided in Figure 3. An assembly drawing
for the Evaluation Board is shown in Figure 4.
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
Package Dimensions
The PCB layout footprint for the SKY65362-11 is provided in
Figure 5. Figure 6 shows the package dimensions for the 36-pin
MCM, and Figure 7 provides the tape and reel dimensions.
The SKY65362-11 is rated to Moisture Sensitivity Level 3 (MSL3)
at 260 C. It can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
PCB Design and SMT Assembly/Rework Guidelines for MCM-L
Packages, document number 101752.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015
7
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
J10
PFWD
PREV
IALARM
ANT_SEL
CTX
R5
1Ω
CPS
R4
1Ω
CSD
R3
1Ω
R2
1Ω
L7
5.1 nH
C14
1 nF
C15
22 pF
C10
100 pF
PREV
L5
1 kΩ
L6
1 kΩ
CSD
CPS
CTX
IALARM
ANT_SEL
PA_IN
GND
PFWD
PREV
CSD
CPS
CTX
IALARM
ANT_SEL
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
J6
SMA
10
11
12
13
14
15
16
17
18
RX
GND
GND
GND
LNA_IN
C11
100 pF
GND
GND
GND
GND
GND
GND
GND
ANT1
GND
SKY65362
U2
GND
RX_FLT
PFWD
1
2
3
4
5
6
7
8
9
GND
VSUP1
VSUP2
VCC1
GND
VCC0
GND
VCC2
GND
PAD
37
C17
10 nF
J7
L8
22 nH
C12
DNI
C16
10 nF
SMA
C13
33 pF
2
4
6
8
10
12
14
16
18
20
22
24
26
28
GND
ANT2
C18
4.7 µF
1
3
5
7
9
11
13
15
17
19
21
23
25
27
J8
SMA
J9
SMA
Figure 3. SKY65362-11 Evaluation Board Schematic
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8
January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B
Y1558
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
Y1557
Figure 4. SKY65362-11 Evaluation Board Assembly Drawing
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015
9
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
6.3 mm
Pin 36
Pin 1 Indicator
0.20 x 0.20
36X 0.75 mm
36X 0.25 mm
Pin 1
Stencil aperture size of 80% to 100%
of the module/package solder mask openings
6.3 mm
9X 0.875 mm
Exposed center pads
Package Outline
9X 0.875 mm
0.125 mm Typ
0.5 mm Pitch
Stencil Aperture
Pin 36
6.3 mm
6.4 mm
Pin 36
Pin 1 Indicator
0.20 X 0.20
34X 0.75 mm
34X 0.25 mm
Pin 1
36X 0.4 mm
Pin 1
0.6 mm Pitch
Thermal via array
ø0.3 mm on 0.6 mm pitch
improves thermal performance
36X 0.85 mm
Opening size of 60% to 100%
of the exposed center
opening shown
2X 1.4375 mm
6.4 mm
6.3 mm
0.25 mm Typ
Package
Outline
Package
Outline
0.6 mm Pitch
2X 1.4375 mm
0.5 mm Pitch
0.5 mm Pitch
Metallization
Solder Mask Opening
Notes:
1. All dimensions are in millimeters, unless otherwise specified.
2. Thermal vias should be resin filled and capped in accordance with IPC-4761Type VII vias.
Recommended Cu thickness is 30 to 35 µm.
Figure 5. SKY65362-11 PCB Layout Footprint
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
10
January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B
Y1554
C
Pin 36
0
Pin 1
Indicator
36X SMT Pad
0.1 M A B C
Top
B
4X 2
6
10X 1
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
Pin 1 Indicator
See Detail D
Pin 1
4X 2
10X 1
4X 0.5
6
0
4X 1.5
4X 1.5
A
0.9 ± 0.1
0.15 A B C
0.1
Top View
Solder Mask Openings
0.2 A B C
See Detail B
Bottom View
Side View
0.875
(0.1)
0.5 ± 0.1
4X 0.5
See Detail A
0.875
0.875
0.875
0.4 ± 0.05
0.25 ± 0.05
Pin 1 Indicator
0.2 X 0.2
5X R0.05 Max
4X R0.05 Max
Metal Pad Edge
Detail B
Scale: 2X
8X This Rotation
Detail A
Detail C
Scale: 2X
1X This Rotation
Scale: 2X
9X This Rotation
9X Rotated 180 º
9X Rotated 90 ºCW
9X Rotated 90 ºCCW
Notes:
1. Dimensions and tolerances per ASME Y14.5-1994.
2. All dimensions are in millimeters unless otherwise specified.
3. Pad definitions per details on drawing.
Y1555
Figure 6. SKY65362-11 36-Pin MCM Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015
11
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
8.00 (P1)
Ø1.50 ±0.10
4.00 (Po)
2.00 ±0.05
B
1.75 ±0.10
5.50 ±0.05
Pin 1
Refer to
Special Notes
A
6.35 (Bo)
A
12.00 ±0.30
0.3 ±0.02
7° Max
1.59 (Ko)
B
Ø1.50 Min
Section B-B
Notes:
1. Carrier tapes must meet all requirements of Skyworks GP01-D233
procurement spec for tape and reel shipping.
2. Carrier tape shall be black conductive polystyrene.
3. Cover tape shall be transparent conductive pressure sensitive
adhesive (PSA) material with 9.30 mm width.
4. ESD-surface resistivity shall be <=1 x 10 10ohms/square per
EIA, JEDEC TNR specification.
5. Po/P1 10 pitches cumulative tolerance on tape: ±0.20 mm.
6. Ao & Bo measurement point to be 0.30 mm from bottom pocket.
7. All dimensions are in millimeters.
8. Part Number: eC3-MCM0606-12-8-F3-L
(Please indicate on Purchase Order)
6.35 (Ao)
8° Max
Special Notes:
1. Pin 1 orientation shall be on the Top Left for the:
SKY73022-21 and -31
SKY73023-21 and -31
2. Pin 1 orientation shall be on the Top Right for all other 6 x 6 mm MCMs and RFLGAs.
Section A-A
Y1556
Figure 7. SKY65362-11 Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
12
January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B
DATA SHEET • SKY65362-11: HIGH-POWER RF FEM
Ordering Information
Model Name
SKY65362-11: High-Power RF FEM
Manufacturing Part Number
SKY65362-11
Evaluation Board Part Number
SKY65362-11-EK1
Copyright © 2013-2015 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for
identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by
reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015
13