MIC4043 Low-Voltage, Secondary-Side Shunt Regulator General Description Features The MIC4043 is a shunt regulator optimized for secondaryside regulation in low-voltage power supplies. Featuring an output stage guaranteed to swing within 400mV of ground, the MIC4043 can be used in power supplies operating down to 1.8V, even with opto-isolators requiring greater than 1.2V of headroom. • Ideal for 1.8V switching converters • Low-voltage operation: − 400mV maximum saturation over operating temperature range • Easy-to-use − Voltage in, current out • 2% voltage tolerance over operating temperature range In power supply applications, the MIC4043 normally drives the LED of an optically isolated feedback circuit. The MIC4043 monitors a resistively-divided output voltage and sinks error current through the opto-isolator’s LED (secondary side); the opto-isolator’s transistor (primary side) provides this signal to the controller’s feedback input. The MIC4043 is also practical for other voltage-monitoring applications requiring an open- collector output. Applications • Optically-isolated, low-voltage power supplies • Low-voltage discrete regulator control The MIC4043 replaces conventional ’431-type shunt regulators to allow low-voltage applications where there is inadequate headroom for a 2.5V regulator in series with an opto-isolator. Replacing ’431-type devices requires only a minor change to the way that the resistive-divider values are calculated. Datasheets and support documentation are available on Micrel’s web site at: www.micrel.com. Typical Application 200kHz DC-to-DC Flyback Converter Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com October 10, 2014 Revision 2.0 Micrel, Inc. MIC4043 Ordering Information (1) Part Number Marking Voltage (V) Tolerance Configuration Temperature Range Package MIC4043YM4 RB1D 1.245 1% Open Collector –40°C to +85°C SOT-143 Note: 1. Underbar ( ) symbol may not be to scale. Pin Configuration SOT-143 (M4) (Top View) Pin Description Pin Number Pin Name 1 IN 2 SNK Sink (Output): NPN open collector output. 3 GND Ground 4 FB October 10, 2014 Pin Function Input: Supply voltage input. Feedback (Input): Feedback input from external voltage-divider network. 2 Revision 2.0 Micrel, Inc. MIC4043 Absolute Maximum Ratings(2) Operating Ratings(3) Input Voltage (VIN) ........................................................ +15V Output Voltage (VSNK). .................................................. +15V Storage Temperature (TS) ......................... −65°C to +150°C (4) ESD Rating Human Body Model ................................................. 2kV Machine Model ...................................................... 200V Input Voltage (VIN) ........................................................ +10V Output Voltage (VSNK)................................................... +10V Maximum Output Current (ISNK) .................................. 15mA Temperature Range (TA) ............................. −40°C to +85°C Electrical Characteristics(5) TA = +25°C, bold values indicate –40°C ≤ TA ≤ +85°C, unless noted. Parameter Reference Voltage Condition Min. (5) Typ. Max. 1.245 V ±1 Reference Voltage Tolerance ±2 35 Supply Current ISNK = 0mA Transconductance (∆ISNK / ∆VIN) 1mA < ISNK < 15mA Output Transistor Saturation Voltage ISNK = 15mA Output Leakage VSNK = 5V, output transistor off 65 70 3.5 150 % µA S 2 160 Units 250 400 0.5 1 mV µA Notes: 2. Exceeding the absolute maximum ratings may damage the device. 3. The device is not guaranteed to function outside its operating ratings. 4. Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5kΩ in series with 100pF. Machine model, 200pF. 5. Reference voltage is not referenced to ground. The reference is between the IN and FB pins. October 10, 2014 3 Revision 2.0 Micrel, Inc. MIC4043 Test Circuit Test Circuit 1: Compensation (Bode Plot) Circuit Test Circuit 2: Transient Response Circuit October 10, 2014 4 Revision 2.0 Micrel, Inc. MIC4043 Functional Characteristics October 10, 2014 5 Revision 2.0 Micrel, Inc. MIC4043 Functional Diagram October 10, 2014 6 Revision 2.0 Micrel, Inc. MIC4043 Functional Description The MIC4043 combines a GM amplifier, precision 1.245V reference, and a pass transistor in a single package. The operation of the MIC4043 is similar to conventional shunt regulators such as the industry standard ’431. In a closed loop system, the MIC4043 maintains the desired feedback voltage at the FB pin by sinking current onto the SNK pin proportional to the error voltage at the FB pin. The ratio of sink current to error voltage is the transconductance of the device. Reference The MIC4043 uses a high-side reference. External voltage dividers providing feedback to the MIC4043 will be inverted when compared to those used with ’431equivalent devices. Behavior The external feedback voltage is compared to the internal high-side 1.245V reference. If the feedback voltage, VFB, is less than VIN – VREF, the amplifier provides no drive to the sink transistor. If the feedback voltages are greater than VIN – VREF, the amplifier drives the pass transistor which sinks current to ground. October 10, 2014 7 Revision 2.0 Micrel, Inc. MIC4043 Application Information Replacement of ‘431-Type Devices Since the MIC4043 uses a high-side reference, external voltage dividers providing the feedback voltage will be inverted when compared to those used with ’431equivalent devices. Voltage Detector Figure 1 shows a simple voltage threshold detector with a logic output. The industry-standard ‘431 is also typically used in series with an opto-isolator LED. This configuration has a voltage drop of at least 2.5V for the ‘431 plus 1.4V for the LED (3.9V). More recent lower-voltage shunt regulators require at least 1.25V of headroom in addition to the 1.4V for the opto-isolator, for a total of 2.65V. The MIC4043 removes the need to place the shunt reference in parallel with the opto-isolator. The MIC4043 combines a 1.245V reference in conjunction with an error amplifier that drives an NPN output transistor. The NPN transistor is connected in series with the opto-isolator and regulates the drive current in the opto-isolator. Unlike conventional shunt regulators, the MIC4043 does not have to connect the shunt reference in series with the opto-isolator, so the voltage drop is just the saturation voltage for one transistor, typically 160mV at full load. Figure 1. Voltage Detector High-Current Regulator For the high-current regulator shown in Figure 2, headroom is equal to the saturation voltage of Q1 plus the saturation voltage of the MIC4043 (VSAT(MIN) = 200mV). Compensation The non-inverting side of the error amplifier is connected to the high-side reference; the reference is connected to the IN pin. The inverting side of the error amplifier is brought out to the FB pin. For some applications, no compensation is needed, but for most, some resistor capacitor network is necessary between the FB pin and GND pin. The value of the feedback capacitance is application specific, but for most applications 100pF to 3000pF is all that is needed. Changing the feedback capacitor changes the loop response; that is, phase and gain margin. An empirical way to check overall system loop response, if a network analyzer is not available, is to step load the output of the systems from 10% to 100% of nominal load. The resultant small signal response at the output of the systems will provide an idea of which direction to go based on the overshoot and settling time of VOUT. October 10, 2014 Figure 2. High-Current Regulator 8 Revision 2.0 Micrel, Inc. MIC4043 Off-Line 1.8V/2A Power Supply Figure 3. Off-Line 1V/2A Power Supply Figure 4. 1.8V/1A Output Bode Plot (θ Margin = 102°) October 10, 2014 Figure 5. 1.8V/2A Output Bode Plot (θ Margin = 87°) 9 Revision 2.0 Micrel, Inc. MIC4043 Off-Line 2.5V/2A Power Supply Figure 6. Off-Line 2.5V/2A Power Supply Figure 7. 2.5V/1A Output Bode Plot (θ Margin = 83°) October 10, 2014 Figure 8. 2.5V/2A Output Bode Plot (θ Margin = 83°) 10 Revision 2.0 Micrel, Inc. MIC4043 Off-Line 3.3V/2A Power Supply Figure 9. Off-Line 3.3V/2A Power Supply Figure 10. 3.3V/1A Output Bode Plot (θ Margin = 82°) October 10, 2014 Figure 11. 3.3V/2A Output Bode Plot (θ Margin = 80°) 11 Revision 2.0 Micrel, Inc. MIC4043 Off-Line 5V/2A Power Supply Figure 12. Off-Line 5V/2A Power Supply Figure 13. 5V/1A Output Bode Plot (θ Margin = 67°) October 10, 2014 Figure 14. 5V/2A Output Bode Plot (θ Margin = 61°) 12 Revision 2.0 Micrel, Inc. MIC4043 Package Information and Recommended Landing Pattern(6) SOT-143 (M4) Note: 6. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. October 10, 2014 13 Revision 2.0 Micrel, Inc. MIC4043 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2000 Micrel, Incorporated. October 10, 2014 14 Revision 2.0