Products Related to Common Sockets and DIN Tracks CSM_common_sockets_DS_E_3_1 A Wide Variety of Square and Round Sockets in Front-mounting and Back-mounting Models • Models available with finger protection. • Hold-down Clips and Socket Bridges for PYF Sockets are also available. • New screwless models available. Models Used with Common Sockets Sockets Item Model Group name Proximity Sen- E2C sors Number of pins 8 P2CF-08 E2C-AK4A 11 P2CF-11 E2C-GE4A E2C-GF4A 8 PYF08A 61F-GP-N8 61F-APN2 PF083A 8 61F-HSL Level Devices 61F K7L 61F-IP 61F-G1P, -G2P 14 14PFA MY1, MY2 MY (Q, K, H) MY4, MYQ4 MY4Z-CBG MY2K, MY4H G2A(K) LY1, LY2 LY3 LY4 G7K-412S G2A, G2A-434 G2AK MK2P MK(K) MK3P MK2KP MM2(X)P P3G MM3P MM2(X)KP P3GA MM PY PL 8 P2RF-08(-E) --- Generalpurpose Relays and Solid-state Relays 8 11 PYF PY 14 8 11 PTF 14 14 PYF MM3XP MM3(X)KP MM4(X)P MM4(X)KP G4Q --- G3F G3F(D) Series G3FM G3H G3H(D) Series G3B G3B(D) Series G9H G9H-2@@S Number of pins Applicable Sockets Frontmounting 8 8PFA 11 PFA PL 14 8 8PFA1 PL PYF PY 8 PTF PF083A PT PTF PT PL 5 P2RF-05@ P2R -05@ G2R-2-S@ 8 P2RF-08@ P2R -08@ G3R --- 5 P2RF-05@ P2R -05@ G7T G3TA G7T G3TA 5 P7TF-05 --- G7S G7S-4A2B-E G7S-3A3B-E 14 P7S-14F-END P7S -14P-E G7SA-3A1B G7SA-2A2B 10 P7SA-10F P7SA-10F-ND P7SA @-10P G7SA-5A1B G7SA-4A2B G7SA-3A3B 14 P7SA-14F P7SA-14F-ND P7SA @-14P H3CA-8(H) 8 G2R G7SA --PY P3G PL H3CA PL Timers Backmounting G2R-1-S@ PT 8 PF083A(-E) 11 PF113A(-E) Model Group name 8PFA 11 PF113A K7L-AT50/AT50D K7L-U/-UD Backmounting 8PFA1 61F-03B, -04B 61F-GP-N 61F-GPN-V50 61F-GPN-BT/BC MY3 Generalpurpose LY Relays and Solidstate Re- G7K lays Front-mounting E2C-AM4A 61F-UHS Item Applicable Sockets H5CN H5CX H5CZ H3CA-A 11 H5CN-@M 11 Other H5CN models H5CX-L8@ H5CX-A11@ H5CZ-L8@ P3GA PL P3GA P2CF 8 P3G 8 P3G 11 8 P3GA P3G 1 Products Related to Common Sockets and DIN Tracks Item Model Group name H3CR-A8@ H3CR-F8@ H3CR-G8@ H3CR-H8@ H3CR H3M H3CR-A H3CR-AS H3CR-AP H3CR-F H3CR-FN H3CR-HRL Number of pins Applicable Sockets Front-mounting P3G PL 8 P2CF P3GA PL 11 --- 8 PF085A H3Y-2 8 H3Y-4 14 8 H3YN-4@ 14 H3RN-1@ 5 H3RN-2@ 8 RD2P --- 8 8PFA1 H2C --- 8 H3RN H7CX H7CX-A11@ H7CZ H7CZ-L8@ 8 H7CN-@M 11 Counters H7CN E5CN TemE5C2 perature Control- E5CS lers E5L Signal Converters Component Protective Components Products for Highvoltage Power Receiving Equipment Annunciators PYF H3YN-2@ H3YN Other H7CN models E5CN-@U --E5CS-@1, @2 Other E5CS models --K3FK models not listed below K3FK K3FK-G@ K3FK-GS@ K3FK-SL-?5-@ SE SE-KP@N SAO SAO-@ APR K2CU SDV APR-S APR-S380/-S440 K2CU-P SDV-F@@/-FH@T SDV-D@@ P2RF-@-E P2CF PF085A 11 P2R @-@7P For Square Sockets Sockets PYF08M P3G PL PY@(QN) PT@(QN) PYC PYC-P PYC-P PYC-S MY@I * LY@I --- PYC-P2 MY4H --- PYC-P PY@-02 PT@-0 PYC-P PYC-A1 MY2Z@-CR MY3@-CR LY@-CR Y92H-3 --- PYC-1 G2A(K) Series PYC-A2 --- PYC-2 PYC-3 PYC-5 G7K PKC --- H3Y Y92H-3 --- PYC-3 PYC-5 Y92H-4 Note: The @ in the model number is replaced with 08, 11, or 14. * If you use a Hold-down Clip with the MY2I, you cannot use the PYF08A. Use the PYF14A. P3G P2CF 8 P3GA For Round Sockets Sockets P3G 11 P3GA 8 P3G 14 PTF14A --- 8PFA (Included 8 with Converter) 11PFA 11 (Included with Converter) 8 MY@, MY@N, MY@-D, MY2@-CR, MY4@-CR, MY4Z@-CR, MY@-TU, MY2K, MY@N-D2, LY@, LY@N, LY@-TU, MYQ@, G3H(D) Series, G3F(D) Series, G3FM, and G9H PYF@A PTF@A PL P3G --- Applicable models PF083A PF113A PL08 (-Q) PL11 (-Q) 61F-03B, -04B PFC-A1 PLC 61F-GP-N, -GPN-BT 61F-GP-N8 ?61F-APN2 PFC-N8 PHC-5 MK2P Series, MK2KP, MK3P@(-US), and G3B(D) Series PLE08-0 PLE11-0 P2CF-11 PLC-10 --- PLC PFC-A1 8PFA1 --- MK3ZP MK3LP PF083A PL08 PFC-A6 PLC-7 --- --- --- MYA-NA1, -NB1 MYA-LA1, -LB1 MYA-NA2, -NB2 MYA-LA2, -LB2 PL08 MYA-LA12, -LB12 PFC-A7 PLC-8 --- --- PL15 APR-S PFC-A6 PLC-7 --- --- PL08 APR-S380/-S440 --- --- --- Y92H-1 PL11 and P3GA-11 LG2 PFC-A7 PLC-8 --- --- K6EL --- Y92H-1 --- --- 11 P2CF-11 8 8PFA1 14 14PFA LG2-@ 8 PF083A K6EL K6EL-@ 11 P2CF-11 MYA PY P3GA 8 11 P3G PL P3GA LG2 AGF Hold-down Clips Applicable models Timers H3Y Backmounting AGF-1-P5 8 8PFA1 MYA-NA1, -NB1 8 PF083A MYA-NA2, -NB2 MYA-LA1, -LB1 MYA-LA2, -LB2 MYA-LA12, -LB12 11 PF113A PL11 --- PLC-1 Note: 1. The 8PFA(1), 11PFA, and 14PFA are held with hooks. 2. The PL15, PL20, and PF202, as well as models not given in the above table, require panel processing for installation. 3. The PF085A Hold-down Clip is included with the H3M and H2A. It is an option (sold separately) for the H2C. PL 2 Products Related to Common Sockets and DIN Tracks Ordering Information Square Sockets Model P2R (back-mounting), pages 11 and 12 P2RF (front-mounting), page 9 Number of pins Solder terminals P7TF (frontmounting), page 12 PCB terminals P2RF-05 Approx. 27 g P2RF-05-E* Approx. 38 g P2RF-05-S Approx. 36 g P2R-05A Approx. 5 g P2R-05P Approx. 5 g P2R-057P Approx. 5.5 g P2RF-08 Approx. 33 g P2RF-08-E* Approx. 38 g P2RF-08-S Approx. 40 g P2R-08A Approx. 5 g P2R-08P Approx. 5 g P2R-087P Approx. 5.5 g P7TF-05 Approx. 28 g 5 pins --- 8 pins Note: 1. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals. 2. To remove the Relay, pull the lever on the Socket with your fingers supporting the lever and the opposite side of the Relay case, and jiggle the Relay. * Use a #1 Phillips screwdriver to tighten the screws on this Socket. Minimum Order Lot The following models are available at the minimum order lot specified below. Number of pins Model P2RF P2R P7TF 5 pins P2RF-05 P2R-05A P2R-05P P7TF-05 8 pins P2RF-08 P2R-08A P2R-08P --- Model Number of pins 8 pins Minimum order lot (pcs) 10 PY (back-mounting), page 15 PYF (front-mounting), page 14 Solder terminals PYF08A Approx. 32 g PYF08M Approx. 26 g PYF08A-E *1 PYF08S Approx. 46 g PY08 Approx. 8 g Wrapping terminals PY08-Y1 PY08-Y3 PY08QN Approx. 12 g PY08QN2 PY11 Approx. 9 g PY11-Y1 PY11QN PY11QN2 PY11QN-Y1 PY11QN2-Y1 PY14 Approx. 10 g PY14-Y1 PY14-Y3 PY14QN Approx. 14 g PY14QN2 PY14QN-Y1 PY14QN2-Y1 PY14QN-Y3 PY14QN2-Y3 1 PYF11A Approx. 43 g PCB terminals PY08-02 *2 Approx. 7.2 g PY08QN-Y1 PY08QN2-Y1 ? PY11-02 *2 11 pins PYF14A Approx. 49 g 14 pins PYF14A-E*1 PYF14T Approx. 53 g PY14-02 *2 PYF14S Approx. 62 g 3 Products Related to Common Sockets and DIN Tracks Note: 1. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals. 2. Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards. *1. Use a #1 Phillips screwdriver to tighten the screws on this Socket. *2. The structure does not resist flux. Manual soldering is recommended for this product. Model PT (back-mounting), page 18 PTF (front-mounting), page 17 Number of pins Solder terminals PTF08A-E *1 PTF08A Approx. 47 g Wrapping terminals PCB terminals PT08 Approx. 11 g PT08QN Approx. 10.4 g PT08-0 *2 Approx. 8 g PT11 Approx. 13 g PT11QN PT11-0 *2 Approx. 12.2 g PT14 Approx. 17 g PT14QN Approx. 20 g PT14-0 *2 Approx. 16.2 g 8 pins PTF11A Approx. 61 g 11 pins PTF14A-E *1 PTF14A Approx. 77 g 14 pins Note: The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals. * Use a #1 Phillips screwdriver to tighten the screws on this Socket. * The structure does not resist flux. Manual soldering is recommended for this product. Minimum Order Lot Number of pins Model The following models are available at the minimum order lot specified below. PYF PY PTF PT 8 pins PYF08A PYF08M PY08 PTF08A PT08 11 pins PYF11A PY11 PTF11A PT11 14 pins PYF14A PY14 PTF14A PT14 Model Number of pins Model 10 P7S/P7SA, pages 20 and 21 P7LF (front-mounting), page 20 P7LF-06 Approx. 60 g 6 pins Minimum order lot (pcs) Number of pins Front-mounting PCB terminals P7SA-10F Approx. 44 g P7SA-10F-ND Approx. 44 g P7SA-10P Approx. 9 g P7S-14F-END Approx. 110 g P7S-14P-E Approx. 25 g P7SA-14F Approx. 59 g P7SA-14F-ND Approx. 59 g P7SA-14P Approx. 10 g 10 pins 14 pins Note: Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards. 4 Products Related to Common Sockets and DIN Tracks Round Sockets Model PF (front-mounting), page 23 Number of pins P2CF (front-mounting), page 24 PF083A Approx. 34 g P2CF-08 Approx. 55 g PFA (front-mounting), page 25 8PFA Approx. 57 g PL (back-mounting), page 27 P3G (back-mounting), page 26 Solder terminals P3G-08 Approx. 40g Wrapping terminals PCB terminals PL08 Approx. 14 g PL08-Q PLE08-0 Approx. 15 g Approx. 10.6g PL11 Approx. 15 g PL11-Q Approx. 18.5A PF083A-E * P2CF-08-E 8PFA1 Approx. 66 g 8 pins Note: The Y92A-48G Terminal Cover can be used to provide finger protection. PF085A Approx. 40 g PF113A Approx. 47 g P2CF-11 Approx. 70g PF113A-E * P2CF-11-E 11PFA Approx. 74 g P3GA-11 Approx. 47 g PLE11-0 Approx. 10.8 g 11 pins Note: The Y92A-48G Terminal Cover can be used to provide finger protection. 14PFA Approx. 104 g 14 pins --- PL15 Approx. 28 g --- --- --- --- --- --- PL20 Approx. 17 g 20 pins --- --- --- --- Note: The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals. * Use a #1 Phillips screwdriver to tighten the screws on this Socket. Minimum Order Lot Number of pins The following models are available at the minimum order lot specified below. PF Model P2CF PFA P3G PL 8 pins PF083A, PF085A P2CF-08, P2CF-08-E 8PFA. 8PFA1 P3G-08 PL08 11 pins PF113A P2CF-11, P2CF-11-E 11PFA P3GA-11 PL11 14 pins --- --- Minimum order lot (pcs) 20 10 14PFA --20 PL15 10 Terminal Cover Model Y92A-48G Appearance Note: Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards. 5 Products Related to Common Sockets and DIN Tracks Hold-down Clips (Unit: mm) For Square Sockets PHC-12 PKC One Set (2 Clips) PYC-A1 Approx. 0.54 g One Set (2 Clips) PTC-1 5 4.5 PYC-E1 One Set (2 Clips) PYC-A2 One Set (2 Clips) 3 29 7° 71.8 2.7 3 4.5 PYC-P Approx. 1.4 g 36.3 36.3 40.7 4.5 1 9.6 PYC-P2 Approx. 1.2 g PYC-S Approx. 1.8 g 4.5 4.5 1.2 4.5 PYC-1 Approx. 6 g 8 28 5.8 4.3 1.2 PYC-3 PYC-2 8 28 5 Approx. 3 28.8 28 Approx. 3 ±0.1 4.5 1.2 9.4 10 5 29 max. 42.8 36.3 Approx. 16 2.5 5 max. 10 Approx. 30.5 2.7 5 max. 5 max. 3.3 29.5 2.5 52 58.2 38.5 PYC-5 PYC Approx. 0.2 g Y92H-1 Y92H-3 One Set (2 Clips) 10 10 3 6 44.5 Y92H-4 R9 5 max. 5 30.5 3.5 24.5 2.5 3.7 3.7 53 20 72.9 1.5 34.5 (84°) 1.5 34.7 23.5 41.7 33.7 6 6 2 10 4.5 1.2 4.5 For Round Sockets PFC-A1 Approx. 2.2 g One Set (2 Clips) PFC-A6 Approx. 2.4 g One Set (2 Clips) 73.3 62 PLC Approx. 2.4 g One Set (2 Clips) 94 74.5 4.5 56.6 69.2 65.7 56.3 8 8 4.5 6 9 6 PLC-8 Approx. 6.4 g One Set (2 Clips) PLC-10 Approx. 2.0 g One Set (2 Clips) 4.5 PLC-12 Approx. 5.4 g One Set (2 Clips) Minimum Order Lot The following models are available at the minimum order lot specified below. 5 Type 90.2 86.7 66.2 Model 64.3 8 8 9 PLC-7 Approx. 3.0 g One Set (2 Clips) 95.2 7.6 6 PLC-1 Approx. 2.6 g One Set (2 Clips) 4.6 4.6 4.6 60.8 PFC-A7 Approx. 3.0 g One Set (2 Clips) For Square Sockets 6 For Round Sockets Minimum order lot (pcs) PYC-A1 PYC-P 100 PYC-A2 PYC-S PYC-1 PYC-2 PYC-3 PYC-5 10 PFC-A1 PFC-A6 PFC-A7 PLC 20 6 Products Related to Common Sockets and DIN Tracks Specifications Socket Characteristics Model Continuous carry current P2RF-05(-E)(-S) 10 A P2RF-08(-E)(-S) 5A Dielectric strength Between contact terminals of same polarity: 1,000 VAC for 1 min Between coil and contact terminals: 4,000 VAC for 1 min Insulation resistance*1 Remarks 1,000 MΩ min. Between contact terminals of different polarity: 3,000 VAC for 1 min Between contact terminals of same polarity: 1,000 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 4,000 VAC for 1 min P2R-05P 10 A P2R-08P 5A Between contact terminals of same polarity: 1,000 VAC for 1 min Between coil and contact terminals: 4,000 VAC for 1 min 1,000 MΩ min. Between contact terminals of different polarity: 3,000 VAC for 1 min Between contact terminals of same polarity: 1,000 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 4,000 VAC for 1 min P2R-057P 10 A P2R-087P 5A Between contact terminals of same polarity: 1,000 VAC for 1 min Between coil and contact terminals: 5,000 VAC for 1 min 1,000 MΩ min. Between contact terminals of different polarity: 3,000 VAC for 1 min Between contact terminals of same polarity: 1,000 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 5,000 VAC for 1 min Between contact terminals of same polarity: 1,000 VAC for 1 min P2R-05A 10 A Between ground terminals: 1,500 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 4,000 VAC for 1 min Between contact terminals of different polarity: 3,000 VAC for 1 min P2R-08A 5A P7TF-05 5A Between contact terminals of same polarity: 1,000 VAC for 1 min Between ground terminals: 1,500 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 4,000 VAC for 1 min PYF08A(-E)(-S) PYF11A PYF14A(-E)(-S) Between terminals: 2,000 VAC for 1 min 100 MΩ min. 7 A, -S models: 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. 5A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. 3 A, -S models: 5A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. 1,000 MΩ min. PY08(-Y1) 7A Between terminals: 1,500 VAC for 1 min PY08QN(-Y1) 7A Between terminals: 1,500 VAC for 1 min 100 MΩ min. PY08-02 7A Between terminals: 1,500 VAC for 1 min 100 MΩ min. PY11(-Y1) 5A Between terminals: 1,500 VAC for 1 min 100 MΩ min. PY11QN(-Y1) 5A Between terminals: 1,500 VAC for 1 min 100 MΩ min. PY11-02 5A Between terminals: 1,500 VAC for 1 min 100 MΩ min. PY14(-Y1) 3A Between terminals: 1,500 VAC for 1 min 100 MΩ min. PY14QN(-Y1) 3A Between terminals: 1,500 VAC for 1 min 100 MΩ min. PY14-02 3A Between terminals: 1,500 VAC for 1 min 100 MΩ min. PTF@@A(-E) 10 A Between terminals: 2,000 VAC for 1 min 100 MΩ min. PT@@ 10 A Between terminals: 2,000 VAC for 1 min 100 MΩ min. PT@@QN 10 A Between terminals: 2,000 VAC for 1 min 100 MΩ min. PT@@-0 10 A Between terminals: 2,000 VAC for 1 min 100 MΩ min. The continuous carry current of 10 A for the PYF08S is for an ambient temperature of 55°C. At an ambient temperature of 70°C, the value is 7 A. Between contact terminals of different polarity: 2,000 VAC for 1 min P7LF-06 30 A Between contact terminals of same polarity: 2,000 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 4,000 VAC for 1 min PF@@@A 5A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. P2CF 5A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. P3G(A) 6A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. 8PFA(1) 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. 11PFA(1) 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. PL@(-Q) 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. PLE@@-0 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. P6D-04P 5A P7S-14@-E(ND) 10 A Between contact terminals of same polarity: 1,000 VAC for 1 min Between coil and contact terminals: 3,000 VAC for 1 min 100 MΩ min. Between contact terminals of different polarity: 2,000 VAC for 1 min Between contact terminals of same polarity: 1,500 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 2,000 VAC for 1 min 7 Products Related to Common Sockets and DIN Tracks Model Continuous carry current Dielectric strength Insulation resistance*1 Remarks Between contact terminals of different polarity: 2,500 VAC for 1 min P7SA-10@ 6 A *2 Between contact terminals of same polarity: 1,500 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 2,500 VAC for 1 min Between contact terminals of different polarity: 2,500 VAC for 1 min P7SA-14@ 6 A *2 Between contact terminals of same polarity: 1,500 VAC for 1 min 1,000 MΩ min. Between coil and contact terminals: 2,500 VAC for 1 min *1. The insulation resistance was measured with a 500-VDC insulation resistance meter at the same places as those used for measuring the dielectric strength. *2. There are restrictions in the current. Refer to the General Catalog for the OMRON Safety Components (Cat. No. Y106) for details. Safety Precautions Refer to Common Relay Precautions for general precautions. 8 Products Related to Common Sockets and DIN Tracks Dimensions P2RF (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions P2RF-05 (One Pole) 7±0.2 Mounting Hole Dimensions 2 5-M3.5×8 4.2-dia. hole 4 dia. 9.5 4 35.5 71.5 max. 30±0.05 3 4 4 5 19.5 30 max. 19.5 max. 2 1 M3 (M3 x 16) or 3.5-dia. hole (Top View) 54 max. (Top View) P2RF-05-E (One Pole) (Finger Protection Structure) 5-M3.5×7 Note: Track mounting is also possible. Refer to page 28. 7±0.2 59 max. (80.9 max.)* 48 max. 2 3.2-dia. hole 4 (11) (12) 2 3 (14) 7 39.5±0.1 3.5-dia. hole 4 39.5 5 85.5 max. 35.5 (A1) (A2) 1 M3 or 3.5-dia. hole (Top View) 16 5 61 max. *When mounted on H3RN-1@. 11.5 (Top View) Note: Figures in parentheses indicate DIN standard numbers. Note: Track mounting is also possible. Refer to page 28. P2RF-05-S (One Pole) (Screwless Model) 4 (11) 32.6 3 27.6 18.0 max. (14) 22.6 2 (12) 24.5 --35.3 91.8 max. (A1) (A2) 5 (Top View) Note: Figures in parentheses indicate DIN standard numbers. (5.3) 28.5 (2.4) 32.6 P2RF-08 (Two Poles) 1 2 7±0.2 8-M3.5×8 4.2-dia. hole 4 dia. 35.5 71.5 max. 9.5 6 3 5 4 30±0.05 4 M3 (M3 x 16) or 3.5-dia. hole 4 19.5 max. 19.5 30 max. 7 8 2 1 (Top View) 54 max. (Top View) Note: Track mounting is also possible. Refer to page 28. 9 Products Related to Common Sockets and DIN Tracks P2RF (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions P2RF-08-E (Two Poles) (Finger Protection Structure) 1.5 2 8-M3×8 6+0.2 −0.1 (21) (22) 63 max. (84.9 max.)* 48 max. 2 Mounting Hole Dimensions (11) 6 3 (12) 7 2 5 4 3.2-dia. hole 7 (24) (14) 3 dia. 39.5±0.1 3.5-dia. hole 8 39.5 35.5 85.5 max. 16 4 61 max. * When mounted 11.5 on H3RN-2@. (A1) 4 1 (Top View) Note: Figures in parentheses indicate DIN standard numbers. 6 P2RF-08-S (Two Poles) (Screwless Model) M3 or 3.5-dia. hole (Top View) Note: Track mounting is also possible. Refer to page 28. 3 (21) (11) 5 27.6 22.6 4 (24) (14) 32.6 18.0 max. (A2) 7 (3.4) 2 (22) (12) 24.5 --35.3 91.8 max. (A1) (A2) 8 1 (Top View) (2.4) 28.6 32.6 (5.3) Note: Figures in parentheses indicate DIN standard numbers. Note: 1. If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative. 2. Refer to pages 29 and 30 for the features of Screwless Sockets and for precautions for correct use. 10 Products Related to Common Sockets and DIN Tracks P2R (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions PCB Dimensions P2R-05P (One Pole) 4 14.5 max. 7.5 3.5 1 35.5 max. 3 6 4.5 15 3.5 1.2 6 4.5 4 2 Five, 1.6-dia. holes 15 4 1 1.5 4 5 (5) 7 4 7 36.5 max. (Bottom View) (Bottom View) P2R-08P (Two Poles) 7.5 7.5 3.5 14.5 max. 0.3 5 5 35.5 max. 1 2.8 4 3 2 5 6 7 1 8 Eight, 1.3-dia holes 5 5 20 20 1.5 (4.3) 7.5 (Bottom View) 36.5 max. (Bottom View) P2R-057P (One Pole) 14 max. 0.7 8.7 1 4±0.1 16.4 10.4 3.5 Five, 1.6-dia. holes 1 6 4.5 15 3 4 8.75 2 29.6 37 max. 1 8.7 6±0.1 4 4.5±0.1 15±0.1 4±0.1 (8.75) 1 7.4 5 7±0.1 4 7 (Bottom View) 41 max. (Bottom View) P2R-087P (Two Poles) 14 max. 7.5 1 16.4 10.4 3.5 7.5 0.3 5 5 37 max. 29.1 4 3 2 20 1 8.1 8.9 5 6 7 Eight, 1.3-dia holes 5 5 20 7.4 1 8 (8.1) 7.5 40 max. (Bottom View) (Bottom View) Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative. 11 Products Related to Common Sockets and DIN Tracks P2R (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions Mounting Hole Dimensions P2R-05A (One Pole) 7.5 4.5 14.5 max. 1.2 3 4 2 0.3 6.7 35.5 max. 5 16.7 3.8 1 5 Five, 3 x 1.8-dia. holes 13.6±0.1 6 (Bottom View) 36.5 max. 30.5+00.2 P2R-08A (Two Poles) 7.5 6.5 14.5 max. 1.2 0.3 5 5 35.5 max. 2.6 2.8 4 3 2 5 6 7 1 8 (Use panel with thickness of 1.6 to 2.0 mm.) 20 1.5 Eight, 3 x 1.2-dia. holes 7.5 (Bottom View) 36.5 max. Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative. P7TF (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions Mounting Hole Dimensions 12.5±0.2 P7TF-05 M3 or M4* 19 max. 7+0.2 -0 5-M3.5×8 4 3 62±0.1 2 35.5 71.5 max. 1 M3 5 (Top View) 4 9 12.5±0.2 19.5 59 max. (Top View) Note: Track mounting is also possible. Refer to page 28. * We recommend that you use washers if you use M3 bolts or screws. Washers are not required with M4 bolts or screws. Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is positive. 12 Products Related to Common Sockets and DIN Tracks PYF (Unit: mm) Terminal Arrangement/Internal Connections Dimensions PYF08A Mounting Hole Dimensions PYF08A-E (Finger Protection Structure) 6+0.2 −0.1 Two, 4.2 × 5 mounting holes 6+0.2 −0.1 Two, 4.2 × 5 mounting holes 3.4 8-M3×8 8-M3×8 Two M3 or M4 or 4.5-dia. holes 3.4 4 1 5 8 35.4 72 max. 72 max. 59±0.3 35.4 12 9 14 13 4 4 23 max. (Top View) 4 6 Note: Track mounting is also possible. Refer to page 28. 6 23 max. 16.5 15±0.2 (Top View) 16.5 30 max. 31 max. PYF08M 8-M3.5×7.5 3 dia. 7±0.2 34 max. 4 8 12 1 5 9 14 13 3.5-dia. hole 20±0.1 1.5 44.5 max. 3.5-dia. mounting holes 6.5-dia. countersinking, depth: 11.5 PYF08S (Screwless Model) 3.5-dia. or M3 hole (Top View) 18 max. 38.2 max. 36.5 max. 32.6 27.6 22.6 23.2 max. 12 9 (41) (11) 8 5 (44) (14) 4 1 (42) (3.4) (12) --- 24.5 (A2) 85 max. 35.4 14 (A1) 13 (Top View) 28.6 (5) (5.3) 32.6 PYF11A Two, 4.2 × 5 mounting holes 6+0.2 −0.1 Note: Figures in parentheses indicate DIN standard numbers. Two M3 or M4 or 4.5-dia. holes 3.4 11-M3×8 3 2 1 6 5 4 9 8 7 11 10 59±0.3 35.4 72 max. 4 29.5 max. 6 16.5 30 max. (Top View) 22±0.2 (Top View) Note: Track mounting is also possible. Refer to page 28. 13 Products Related to Common Sockets and DIN Tracks PYF (Unit: mm) Terminal Arrangement/Internal Connections Dimensions PYF14A Two, 4.2 × 5 mounting holes Mounting Hole Dimensions PYF14A-E (Finger Protection Structure) 6+0.2 −0.1 Two, 4.2-dia × 5 6+0.2 −0.1 mounting holes 3.4 14-M3×8 Two M3 or M4 or 4.5-dia. holes 3.4 14-M3×8 59±0.3 35.4 72 max. 35.4 72 max. 22±0.2 (Top View) 4 29.5 max. 3 2 1 4 4 6 6 29.5 max. 16.5 30 max. 8 7 6 5 16.5 31 max. PYF14T Two, 4.2-dia × 5 mounting holes 12 11 10 9 4 14 13 30 23.5 11.5 11 33 max. 7±0.2 Note: Track mounting is also possible. Refer to page 28. 2-M4 (Top View) 59 35.5 70 max. 24.5 (Top View) 17.8 4 Note: Track mounting is also possible. Refer to page 28. 14-M3.5×8 17.4 PYF14S (Screwless Model) 10 36.5 max. 12 11 10 9 (41) (31) (21) (11) 8 7 6 5 (44) (34) (24) (14) 32.6 27.6 31 max. 22.6 4 3 2 1 (42) (32) (22) (12) (3.4) --- 24.55 85 max. 35.4 (A2) 14 (A1) 13 (Top View) (4.15) 28.6 32.6 Note: Figures in parentheses indicate DIN standard numbers. Note: Refer to pages 29 and 30 for the features of Screwless Sockets and for precautions for correct use. 14 Products Related to Common Sockets and DIN Tracks Relay Sockets and Socket Bridges for PYF Bridges within the Same Socket Pitch Applicabl e models Appearance Dimensions (mm) Model Specifications 7 PYD-020B@(2P) 3.2 7 mm 5.6 PYF14A 7 7 PYD-030B@(3P) Max. carry current: 20 A (18 A at 70°C) Ambient operating temperature: -40 to 70°C (with no icing or condensation) Ambient operating humidity: 45% to 85% (with no icing or condensation) Conductor material: Brass Conductor surface treatment: Nickel plating Package qty: 50/bag 3.2 5.6 Note: 1. The @ in the model number is replaced with the insulation color specification code. B: Black, Y: Yellow 2. Specify the number of bags when ordering. Bridges between Adjacent Sockets Pitch Applicabl e models Appearance Dimensions (mm) Model 40° 22 PYD-025B@(2P) 22 mm Specifications 3.3 5.6 PYF08A 154 40° 22 PYD-085B@(8P) Max. carry current: 20 A (18 A at 70°C) Ambient operating temperature: -40 to 70°C (with no icing or condensation) Ambient operating humidity: 45% to 85% (with no icing or condensation) Conductor material: Brass Conductor surface treatment: Nickel plating Package qty: 10/bag 3.3 5.6 40° 29 PYD-026B@(2P) 29 mm 3.3 5.6 PYF14A 203 40° 29 PYD-086B@(8P) Max. carry current: 20 A (18 A at 70°C) Ambient operating temperature: -40 to 70°C (with no icing or condensation) Ambient operating humidity: 45% to 85% (with no icing or condensation) Conductor material: Brass Conductor surface treatment: Nickel plating Package qty: 10/bag 3.3 5.6 Note: 1. The @ in the model number is replaced with the insulation color specification code. B: Black, S: Blue, R: Red 2. Specify the number of bags when ordering. Socket Bridges Pitch Applicable models Appearance and dimensions (mm) 19.7 PYF08S mm Insulating coating 27.5 PYF14S mm 14.3 P2RF-@@-S mm 9 Guide: 1.2 dia. Pitch 14 Model Insulation color PYDM-08SR Red PYDM-08SB Blue PYDM-14SR Red PYDM-14SB Blue P2RM-SR Red P2RM-SB Blue Note: 1. Use the Socket Bridges for relay coil bridge wiring. 2. Specify the number of bags when ordering. Safety Precautions Maximum Carry Current • The total current of all bridged poles must not exceed the maximum carry current of the Socket Bridge. • Make sure that the maximum carry current of the relay contacts is also not exceeded for each pole. • If you use more than one Socket, use End Plates (PFP-M). 15 Products Related to Common Sockets and DIN Tracks PY (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions PY08 PY08-Y1 (L = 42 max.) PY08-Y13 (L = 60 max.) * Mounting hole and PCB dimensions Eight, 3 x 1.2 ellipses 25.5 max. 29.5 max. 5 2.7 *The PY08-Y@ includes the part outlined by the dashed lines above. 24 max. 20 max. L 25.8±0.2 2.6 7.7 21.4+0.2 0 PY08QN PY08QN2 PY08QN-Y1 PY08QN2-Y1 1 *1 29.5 max. 5 *2 *1. The PY08QN(2)-Y1 includes the part 2.7 outlined by the dashed lines above. *2. The figures in the parentheses are for 42 max. (20) 25 41.5 max. (36.5 max.)*2 22 max. 24 max. the PY08QN2(-Y1). 1 4 5 8 9 12 13 14 (Bottom View) 13.2 5.8 4.1 1.0 PY08-02 * The structure does not resist flux. Manual soldering is recommended for this product. 6.35 0.3 6.4 25.5 max. 29.5 max. 4.2 2.7 4.3 22 max. 12.65 Eight, 1.3-dia holes 2 16.5 max. * PY11 PY11-Y1 Eleven, 3 x 1.2 ellipses 25.5 max. 29.5 max. 5 *The PY11-Y1 includes the part outlined by the dashed lines above. PY11QN PY11QN2 PY11QN-Y1 PY11QN2-Y1 42 max. 2.6 7.7 2.7 25.8±0.2 24 max. 20 max. 21.46+0.2 0 1 *1 29.5 max. 5 2.7 *1. The PY11QN(2)-Y1 includes the part outlined by the dashed lines above. *2. The figures in the parentheses are for the PY11QN2(-Y1). 42 max. (20)*2 25 41.5 max. (36.5 max.)*2 22 max. 24 max. 1 2 3 4 5 6 7 8 9 10 13.2 11 (Bottom View) 5.8 4.1 1.0 PY11-02 * The structure does not resist flux. Manual soldering is recommended for this product. 6.35 0.3 25.5 max. 29.5 max. 6.4 4.2 2.7 4.3 22 max. 12.65 Eleven, 1.3-dia holes 2 16.5 max. 16 Products Related to Common Sockets and DIN Tracks Terminal Arrangement/ Internal Connections Dimensions * PY14 PY14-Y1 (L = 42 max.) PY14-Y3 (L = 60 max. ) Mounting hole and PCB dimensions Fourteen, 3 x 1.2 ellipses 25.5 max. 29.5 max. 5 25.8±0.2 The PY14-Y@ includes the part outlined by the dashed lines above. PY14QN PY14QN2 PY14QN-Y1 (L = 42 max.) PY14QN2-Y1 (L = 42 max.) PY14QN-Y3 (L = 60 max.) PY14QN2-Y3 (L = 60 max.) 2.6 7.7 2.7 * 24 max. 20 max. L 21.4+0.2 0 1 *1 29.5 max. 1 2 3 4 5 (20)*2 25 41.5 max. (36.5 max.)*2 2.7 L 5 6 7 8 22 max. 9 10 11 12 24 max. 13 *1. The PY14QN-Y@ and PY14QN2-Y@ include the part outlined by the dashed lines above. *2. The figures in the parentheses are for the PY14QN2(-Y@). * The structure does not resist flux. Manual soldering is recommended for this product. 13.2 (Bottom View) 4.4 5.8 1.0 PY14-02 14 4.1 0.3 6.35 25.5 max. 29.5 max. 2.7 4.3 6.4 4.2 22 max. 12.65 Fourteen 1.3-dia. holes 2 16.5 max. Note: 1. Use a panel with a thickness of 1 to 2 mm when mounting a Socket on it. 2. You can use the PY14-Y1 or PY14QN-Y1 for the MY4 Series, MY4H, MYQ4(Z), or MY2K. 3. You can use the PY14-Y3 or PY14QN-Y3 for H3Y Timers. PTF (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions PTF08A Two, 4.5 × 6 mounting holes Mounting Hole Dimensions 3.4 7±0.2 8-M3.5×8 78.5 max. 35.4 Two, 4.5 dia. or M4 mounting holes 8 30 max. 28.5 max. 2 1 4 3 PTF08A-E (Finger Protection Structure) Two, 4.5 × 6 mounting holes 68±0.3 3.4 8-M3.5×8 6 5 8 7 (Top View) 19±0.2 (Top View) 78.5 max. 35.5 Note: Track mounting is also possible. Refer to page 28. 28.5 max. 8 33 max. 17 Products Related to Common Sockets and DIN Tracks Terminal Arrangement/ Internal Connections Dimensions Mounting Hole Dimensions PTF11A Two, 4.5 × 6 mounting holes Two, 4.5 × 6 mounting holes 3.4 7±0.2 11-M3.5×8 3 2 1 6 5 4 68±0.3 35.4 78.5 max. 9 8 7 11 27.5±0.2 (Top View) (Top View) 8 37 max. 10 Note: Track mounting is also possible. Refer to page 28. 30 max. Two, 4.5 × 6 mounting holes PTF14A 3.4 7±0.2 14-M3.5×8 78.5 max. 35.4 Two, 4.5 dia. or M4 mounting holes 4 3 2 1 45.5 max. 8 30 max. 8 7 6 5 PTF14A-E (Finger Protection Structure) Two, 4.5 × 6 mounting holes 68±0.3 3.4 7±0.2 12 11 10 9 14-M3.5×8 13 14 36±0.2 (Top View) (Top View) 78.5 max. 35.5 Note: Track mounting is also possible. Refer to page 28. 45.5 max. 8 33 max. Note: If you use the PTF08A, PTF08A-E, or PT08 with an LY1 Relay, connect the following terminal pairs: 1-2, 3-4, and 5-6 (for usage at 10 A or higher). PT (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions PT08 PT08QN 5 1.5×1.0 0.3 25.5 29.5 1.0 max. max. 25.5 29.5 max. max. 2.7 9 2.5 20 1.5 35 max. 2.7 24 max. 20.5 max. Mounting hole and PCB dimensions 25.8±0.2 2 21.4+0.2 0 24 max. 2 Eight, 1.7-dia × 3.5 oblong holes PT08-0 2 0.3 *Maintain a sufficient distance from the pattern when using double-sided PCBs. • The structure does not resist flux. Manual soldering is recommended for this product. 7 1 2 3 4 5 6 15.6 10 8 (Bottom View) 5.35 4.6 6.45 29.5 max. 2 1 18 max. 4.3 5* 6.5 22 max. 12.45 6.5 3 Eight, 2.5-dia. holes (±0.1 tolerance) 18 Products Related to Common Sockets and DIN Tracks Terminal Arrangement/ Internal Connections Dimensions PT11 Mounting hole and PCB dimensions PT11QN 0.3 1.5×1.0 5 1.5 30.6 32 max. Eleven, 1.7-dia × 3.5 holes 31±0.2 32 30.6 max. 2.7 9 2.5 20 1.0 1.2 35 max. 2.7 1.2 26.4 26.6+0.3 0 29.5 max. 26.4 10 7 4 1 8 5 2 11 9 6 3 29.5 max. 20.5 max. PT11-0 *Maintain 0.3 a sufficient distance from the pattern when using double-sided PCBs. • The structure does not resist flux. Manual soldering is recommended for this product. (Bottom View) 12.45 6.45 4.6 Eleven, 2.5-dia. holes 5.2 10 21.4 2 5* 10 32 max. 5.8 2.7 4.3 18 max. PT14 6.2 6.2 5.65 (±0.1 tolerance) 29.5 max. PT14QN 0.3 1.5×1.0 5 Fourteen, 1.7-dia × 3.5 holes 42.5 max. 1.5 42.5 max. 2.7 9 2.5 1.0 20 35 max. 26.5 max. 29.5 max. 2.7 20.5 max. 26.5 max. 29.5 max. PT14-0 *Maintain 0.3 41±0.2 a sufficient distance from the pattern when using double-sided PCBs. • The structure does not resist flux. Manual soldering is recommended for this product. 26.6+0.3 0 13 9 5 1 10 6 2 11 7 3 14 12 8 12.45 4.6 6.45 4 5.1 5.8 (Bottom View) 10 31.4 2 2.7 4.3 10 42.5 max. 5* 10 Fourteen, 2.5-dia. holes 6.4 6.4 17.5 max. 26.5 max. 29.5 max. 5.45 (±0.1 tolerance) Note: Use a panel with a thickness of 1 to 2 mm when mounting a Socket on it. 19 Products Related to Common Sockets and DIN Tracks P7LF (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions P7LF-06 Mounting Hole Dimensions Two, M3.5 x 6 (coil side) 51.5 max. 0 Four, M4 × 8 (contact side) 40±0.1 25 1 Two, 4.5 dia. or M4 mounting holes 5 46 max. 40±0.1 55.5 max. 2 4 8±0.05 6 8 (Top View) 9.2±0.05 P7S (Unit: mm) Terminal Arrangement/Internal Connections Dimensions Mounting Hole Dimensions P7S-14F-END Indicator LED 14-M3.0×8 40 max. 33±0.1 41 43 4 42 44 1 7.5 24 62 + 14 13 34 − 23 0 Two, 4.0 dia. or M3.5 33 33±0.1 61 52 51 80 max. 37 17 3.1 5 5.9 90.5 max. (5) P7S-14P-E 70.5 max. 28±0.2 G7S-4A2B-E Mounted 23.5 max. 28±0.2 4.2 Two, 6.5 dia., depth: 8 (21) 2.8 G7S-3A3B-E Mounted (16.9) 14.5 8 57 max. Fourteen, 2.5 dia. 6 7 5×7=35 Two, 3.6 dia. 13.2 (15) 7 6 5×7=35 16.9 8 4.1 14.5 23.5 max. 20 Products Related to Common Sockets and DIN Tracks P7SA (Unit: mm) Dimensions Terminal Arrangement/Internal Connections G7SA-3A1B Mounted P7SA-10F P7SA-10F-ND Mounting Hole Dimensions G7SA-2A2B Mounted 14.5±0.2 Two, 4 dia. or M3.5 R2 22.5 max. 60.5 max. 10-M 3× 8 5 9 max. 44 33 34 44 33 34 43 43 24 22 80±0.2 23 * 21 * 72 max. 12 Indicator LED 12 11 1 0 11 1 − + 0 − + (Top View) 9 max. 4 dia. Note: 1. The Socket is shown with the finger cover removed. 2. Only the -ND Sockets have LED indicators (orange). P7SA-14F P7SA-14F-ND (Top View) * This display circuit is provided only on -ND models. Note: Terminals 23-24, 33-34, and 43-44 are normally open. Terminals 11-12 and 21-22 are normally closed. G7SA-5A1B Mounted G7SA-4A2B Mounted G7SA-3A3B Mounted 22±0.2 Two, 4 dia. or M3.5 R2 30 max. 60.5 max. 14-M3×8 9 max. 64 54 64 54 64 54 63 53 63 53 63 53 44 34 44 34 44 5 43 72 max. * 24 Indicator LED 23 1 33 43 12 22 * 21 1 0 11 33 43 31 12 22 12 21 1 0 11 − + − + 32 * 80±0.2 0 11 − + 9 max. (Top View) 4 dia. Note: 1. The Socket is shown with the finger cover removed. 2. Only the -ND Sockets have LED indicators (orange). P7SA-10P 0.5 50 max. G7SA-3A1B Mounted 0.5 0 11 12 33 34 1 23 24 43 44 + − 15 max. G7SA-2A2B Mounted 41.5 max. 0.4 3.5 (11.1) 11 12 33 34 10.16 1 21 22 43 44 (7.14) 0.8 Three, 2.6 dia. (for M3 tapping screws) 4.1 24.8 39.9 4.1±0.2 0 + − (11.1) (Top View) * This display circuit is provided only on -ND models. Note: Terminals 23-24, 33-34, 43-44, 53-54, and 6364 are normally open. Terminals 11-12, 21-22, and 31-32 are normally closed. (Bottom View) Note: Terminals 23-24, 33-34, and 43-44 are normally open. Terminals 11-12 and 2122 are normally closed. 39.9±0.2 24.8±0.2 13.97 11.43 5.08 5.08 Three, 3.2 dia. (for M3 tapping screws) Ten, 1.1 dia. holes (Bottom View) (±0.1 tolerance) 21 Products Related to Common Sockets and DIN Tracks Dimensions Terminal Arrangement/Internal Connections Mounting Hole Dimensions G7SA-5A1B Mounted P7SA-14P 0.5 60 max. 0.5 0 11 12 33 34 53 54 1 23 24 43 44 63 64 + − 15 max. G7SA-4A2B Mounted 0 11 12 33 34 53 54 + − 41.5 max. 4.1±0.2 1 21 22 43 44 63 64 10.16 G7SA-3A3B Mounted 0.4 0 3.5 (11.1) (11.1) 0.8 Three, 2.6 dia. (for M3 tapping screws) 11 12 31 32 53 54 21 22 43 44 63 64 + − 1 Three, 3.2 dia. 49.9±0.2 (for M3 tapping 24.8±0.2 Fourteen, 1.1 dia. holes screws) (7.14) 13.97 11.43 5.08 5.08 5.08 5.08 (Bottom View) (Bottom View) 4.1 24.8 49.9 Note: Terminals 23-24, 33-34, 43-44, 5354, and 63-64 are normally open. Terminals 11-12, 21-22, and 31-32 are normally closed. (±0.1 tolerance) 22 Products Related to Common Sockets and DIN Tracks PF (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions PF083A Mounting Hole Dimensions 4 7±0.2 8-M3.5×7 Two, 4.2 dia. holes 52 max. 35.4 2 1 8 7 PF083A-E 3.5 33 41 max. 4 2 21 max. 7±0.2 8-M3.5×7 4 Two, 4.2-dia mounting holes 3 4 5 6 8 25 dia. 52 max. 35.4 Two M4 or 4.5-dia. holes (Top View) 33±0.2 4 3.5 23 33 41 max. PF085A Note: Track mounting is also possible. Refer to page 28. 2 21 max. 4 7±0.2 8-M3.5×7 6 5 4 3 Two, 4.5 dia. holes 58 max. 35.4 1.1 33±0.2 40 max. 4 7 8 1 2 2 3.5 (Top View) 21.6 max. PF113A 11-M3.5×7 4 22 7±0.2 35.4 52 max. 4 5 PF113A-E 34 43 max. 4 3.5 2 1 11 10 9 Two M4 or 4.5-dia. holes 31 max. 4 7±0.2 11-M3.5×5 3 2 34±0.2 4 5 6 7 8 52 max. 8 35.4 (Top View) 4.2 Note: Track mounting is also possible. Refer to page 28. 4 5.2 3.5 23 42.8 5.5 31 max. Note: 1. For the PF083A and PF113A, the Socket key slot is on the top. (Applicable model: MK) 2. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals. 23 Products Related to Common Sockets and DIN Tracks P2CF (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions P2CF-08 8-M3.5×7.5 7.8 3 Mounting Hole Dimensions 4.5 Two, 4.5 dia. holes 70 max. 35.4 6 5 4 3 50 max. 4 20.3 max. Two M4 or 4.5-dia. holes P2CF-08-E 8-M3.5×7.5 5 7.8 4.5 40±0.2 6 5 4 3 Two, 4.5 dia. holes P2CF-08-E 3 7 8 1 2 1.3 70 max. 35.4 (Top View) Note: Track mounting is also possible. Refer to page 28. 10A250VAC RESISTIVE 7 8 1 2 40±0.2 50 max. 4 19 20.3 21.5 max. P2CF-11 11-M3.5×7.5 7.8 3 4.5 Two, 4.5 dia. holes 70 max. 35.4 8 7 6 5 P2CF-11-E 4 50 max. 4 Two M4 or 4.5-dia. holes 31.2 max. 11-M3.5×7.5 7.8 5 40±0.2 4.5 9 8 7 6 5 Two, 4.5 dia. holes P2CF-11-E 4 10 11 1 2 3 (Top View) 1.2 70 max. 9 3 35.4 Note: Track mounting is also possible. Refer to page 28. 3 10A250VAC RESISTIVE 10 4 11 1 40±0.2 50 max. 2 30 31.2 max. 24 Products Related to Common Sockets and DIN Tracks PFA (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions Mounting Hole Dimensions 8PFA 8-M3.5×7 7.8±0.2 Two, 4.5 dia. holes 5 4 4 35.4 81 max. 4 118 max. 40±0.2 6 5 4 3 51 max. 24 max. Two M4 or 4.5-dia. holes 8PFA1 8-M3.5×7 40±0.2 7.8±0.2 7 8 1 2 Note: Track mounting is also possible. Refer to page 28. 4 Two, 4.5 dia. holes 5 (Top View) 4 93 max. 4 35.4 130 max. 40±0.2 51 max. 24 max. 11PFA 11-M3.5×7 7.8±0.2 Two, 4.5 dia. holes 5 4 8 7 6 5 4 4 81 max. 35.4 Two M4 or 4.5-dia. holes 118 max. 40±0.2 9 3 10 11 1 2 4 Note: Track mounting is also possible. Refer to page 28. (Top View) 40±0.2 51 max. 33.5 max. 14PFA 7.8±0.2 14-M3.5×7 Two, 4.5 dia. holes 5 4 7 14 6 5 12 4 3 4 35.4 81 max. 118 max. Two, 4.5 dia. or M4 mounting holes 60±0.2 8 9 15 10 1 11 2 4 (Top View) 60±0.2 72 max. Note: Track mounting is also possible. Refer to page 28. 33.5 max. 25 Products Related to Common Sockets and DIN Tracks P3G/P3GA (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions P3G-08 Mounting Hole Dimensions 27 dia. 3 4 5 6 45 --2 1 8 7 4.9 45 Eight, M3.5 SEMS screws 17 (Bottom View) Note: The Y92A-48G Terminal Cover can be used to implement finger protection. P3GA-11 27 dia. 5 6 7 8 4 25.6 45 3 4.5 45 Eleven, M3.5 SEMS screws 6.2 16.3 9 2 1 11 10 --- (Bottom View) Note: The Y92A-48G Terminal Cover can be used to implement finger protection. Terminal Cover (Unit: mm) Appearance Dimensions Y92A-48G 34 Twelve, 6.4 dia. Y92A-48G UP 47.7 × 47.7 48 × 48 P C 16.5 24.6 27.6 47.4 Release Lever Applicable models Appearance (Unit: mm) Dimensions Model 16 PYF08S PYCM-08S 54.4 32.7 28 PYF14S PYCM-14S 52.5 29.6 16.8 P2RF-05-S 40.35 P2CM-S P2RF-08-S 36 26 Products Related to Common Sockets and DIN Tracks PL (Unit: mm) Terminal Arrangement/ Internal Connections Dimensions Mounting hole and PCB dimensions (bottom view) Two, 3.5 dia. or M3 device mounting holes PL08 3.5 4 Two, 3.5 or M3 Socket mounting holes 1 Two, 2 dia. holes 31-dia. hole 30 dia. 50.5 max.40 40±0.3 L 3.9 Approx. 20.5 50.5 max. PL08-Q 4 3.5 1 4 t0.6×1.3 5 3 6 2 51 max. 40 L = 40 mm MK2(Z)P L = 74 mm PU, AMD-S, MM2(X)P, CZ, STP, H3L, TDS, DTS, DSP, TDF, TDV L = 86 mm 61F-GP/-APN, G4Q-212S, RD2P, RDA, TDA, AGF, SE, SAD, K2CU, SDV-F Two 3.5-dia. or two M3 Socket mounting holes 7 1 30 dia. 8 MK2(Z)P 31-dia. hole 40±0.3 (Bottom View) 16 35 max. 35 max. PLE08-0 15 14 Two 3.5-dia. Hold-down Clip mounting holes t0.3 45° 40+0.1 0 27.7±0.5 dia. 29±0.1 dia. Eight, 2.5-dia. holes 21.5 max. PL11 3.5 4 1 Two 2-dia. holes 51 max. 40 Two, 3.5 dia. or M3 device mounting /Hold-down Clip mounting holes 30 dia. 3.9 L = 40 mm MK3P MK2KP Two, 3.5 dia. or M3 Socket mounting holes Approx. 20.5 35 max. PL11-Q 3.5 4 31-dia. hole 1 40±0.3 L 5 6 7 t0.6×1.3 51 max. 16 4 3 2 1 11 8 9 10 PLE11-0 Two, 3.5-dia. holes Applicable model/Hold-down Clip mounting holes t0.3 360° 11 28.7±0.5 29±0.1 dia. 22 max. 4 L = 40 mm MK3P MK2KP L L = 42 mm MK3ZP MK3LP Eleven, 2.5-dia. holes Two, 3.5 dia. or M3 device mounting holes 1 Two 2-dia. holes 41 max. 66 max. 53 L = 42 mm MK3ZP MK3LP (Bottom View) 14 15 4 L = 74 mm MM3P MK2(X)KP 35 max. 35 max. PL15 MK2(Z)P 3.9 2 3 4 12 5 1 11 13 10 15 6 14 9 8 7 MM3XP MM4(X)P MM3(X)KP MM4(X)KP Two, 3.5 dia. or M3 Socket mounting holes 4.2-dia. hole 74 (Bottom View) 45 max. 22 max. 53 27 Products Related to Common Sockets and DIN Tracks Terminal Arrangement/ Internal Connections Dimensions PL20 Two, 3.5-dia. holes 4 Two, 4.5-dia. Relay mounting holes 1 Two, 2 dia. 46.5 max. Mounting hole and PCB dimensions (bottom view) Two, 4-dia. Socket mounting holes 33-dia. hole 19 1 17 18 20 2 3 16 4 15 5 6 14 13 12 10 8 7 11 9 31 max. 3.9 36.5 max. 56±0.2 * Relay mounting holes are not required for the LDNP. (Bottom View) 23 max. 38±0.2 Note: When mounting, pay due attention to the direction of the key groove of applicable Relays. Accessories for DIN Track Mounting (Order Separately) (Unit: mm) DIN Tracks PFP-100N PFP-50N 7.3±0.15 4.5 27±0.15 35±0.3 15 25 10 25 25 1,000 (500)* 15 (5)* 25 10 1 * Dimensions in parentheses are for the PFP-50N. DIN Track PFP-100N2 Model PFP-100N PFP-50N 16 4.5 35±0.3 27 15 25 10 25 25 1,000 End Plate 25 10 24 29.2 Model 15 1 1.5 PFP-100N2 10 6.2 PFP-M 50 M4×8 panhead screw 1.8 1 35.5 35.3 1.8 11.5 Model 10 M4 screw and washer Spacer 1.3 4.8 PFP-M 16 12 5 PFP-S 34.8 44.3 Model PFP-S 16.5 Note: 1. Order the above products in multiples of 10. 2. The Tracks conform to DIN standards. 28 Products Related to Common Sockets and DIN Tracks Features of Screwless Sockets Structured for Easy Wiring Contact terminal (common) Contact terminal (NO) Contact terminal (NC) Release Lever (sold separately) Coil terminals Nameplate (sold separately) Complete Wiring in Three Steps Insert a screwdriver. Screwdriver inserted. Insert the wire. Remove screwdriver to complete wiring. • A spring holds the wire in place to reduce wiring work by 30% (according to OMRON comparison) and eliminates the need to manage torque. • DIN terminal numbers also indicated. Safety Precautions Precautions for Safe Use • Do not move the screwdriver up, down, or from side to side or rotate it while it is inserted in the hole. Doing so may damage internal components in the Socket. Precautions for Correct Use Wiring Tools Applicable Screwdriver Use a flat-blade screwdriver with a tip that is 2.5 mm wide (3.0 mm max.). 2.5 mm (3.0 mm max. ) • Do not insert more than one wire into the same hole. Doing so may cause abnormal heating. • There are two internally connected wiring holes for each terminal. • Insert the screwdriver along the hole wall as shown below. You cannot use a screwdriver with a thick shaft. Applicable Screwdriver (Example) VESSEL No.9900 − (−) 2.5 × 75 Applicable Wires • You can use either solid wires or stranded wires. Applicable wire size: 0.2 to 1.5 mm2 (AWG24 to AWG16) • Strip 8 to 9 mm of insulation from the ends of the wires. Screwdriver • When you remove a Socket from a support rail, insert the end of a screwdriver into the fixture and move the driver as shown by the arrow in the following figure. Screwdriver 8 to 9 mm • If you insert stranded wires without ferrules, make sure that the wires are twisted when you insert them. • If you use bare ferrules, always attach insulating sleeves. • If you insert a wire with a sheath outer diameter of 2.2 mm or less, do not insert the wire far enough so that the sheath is engaged inside the hole, as shown below. Fixture rail • When you use a Release Lever to remove a Relay from a P2RF@@-S Socket, insert a screwdriver at the location shown in the following figure and move the Release Lever in the direction indicated by the arrow to release the lock on the release lever. • Two wires with a sheath outer diameter of 3.2 mm or larger cannot be inserted for the same terminal at the same time. • Use heat-shrinking tubes to indicate wire numbers. 29 Products Related to Common Sockets and DIN Tracks Wiring 12 11 10 9 41 31 21 11 Wire insertion holes Screwdriver insertion hole (1) Insert a screwdriver into a screwdriver insertion hole on the Socket. Cross-section A-A Spring Wire insertion hole Screwdriver Screwdriver insertion hole (2) Press the screwdriver in until it reaches the stopper inside the Socket. The spring at the back of the wire insertion hole will be complete open in this condition. The screwdriver will be held in place even if you remove your hand. (3) With the screwdriver held in place, insert the wire or ferrule into the wire insertion hole. Wire (4) Remove the screwdriver. The spring will hold the wire. This concludes the connection procedure. 30 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2014.11 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2014 All Right Reserved.