Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Applications
Product Description



The SE2603L is a complete 802.11bgn WLAN RF
front-end module providing all the functionality of the
power amplifier, power detector, diversity switch and
50 ohm matching on all RF ports in an ultra compact
form factor.
IEEE802.11b DSSS WLAN
IEEE802.11g,n OFDM WLAN
Access Points, PCMCIA, PC cards
Features







Dual Mode IEEE802.11b, IEEE802.11g,
IEEE802.11n
Integrated PA, TX Filter, Diversity switch
Integrated Positive Slope Power Detector
20 dBm Output Power, 802.11b, 11 Mbps
17 dBm @ 3.0 % EVM, 802.11g, 3.3V
Lead free, halogen free and RoHS compliant
Small plated package, 3 mm x 4 mm x 0.9 mm,
MSL 1
The SE2603L is designed for ease of use, with all the
critical matching and harmonic filtering and integrated
transmit/receive DPDT switch providing a 50 Ω
interface to the antenna. The SE2603L also includes
a transmitter power detector with 20 dB of dynamic
range and a digital enable control for transmitter
power ramp on/off control. The power ramp rise/fall
time is 0.5 μs typical.
Ordering Information
Part No.
Package
Remark
SE2603L
SE2603L-R
SE2603L-EK1
24 pin QFN
24 pin QFN
N/A
Samples
Tape & Reel
Evaluation kit
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
1
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
2
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Functional Block Diagram
Figure 1: Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
3
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Pin Out Diagram
VCC1
24
DET
GND
23
VCC2
22
GND
21
VCC0
20
GND
19
ANT 0
18
1
17 GND
EN 2
GND
3
RF_IN
4
16 ANT1
Bias, Enable
Match
&
15 GND
Match
&
14 C4
Switch Control
GND
5
13 C3
6
GND
7
GND
8
GND
9
RX
10
GND
11
C1
12
C2
Figure 2: SE2603L Pin Out (Top View Through Package)
Pin Out Description
Pin No.
Name
1
Det
2
EN
3
GND
4
RF_IN
5
GND
6
Description
Pin No.
Name
Power Detector Output
14
C4
Power Amplifier Enable
15
GND
Ground
Ground
16
ANT1
Antenna 1
Transmit RF Input
17
GND
Ground
Ground
18
ANT0
Antenna 0
GND
Ground
19
GND
Ground
7
GND
Ground
20
VCC0
Supply Voltage
8
GND
Ground
21
GND
Ground
Receive RF Output
22
VCC2
Supply Voltage
Ground
23
GND
Ground
24
VCC1
Supply Voltage
Paddle
GND
Ground
9
RX
10
GND
11
C1
Switch Control Logic
12
C2
Switch Control Logic
13
C3
Switch Control Logic
Description
Switch Control Logic
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
4
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage
to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions
defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected
workstations.
Symbol
Min.
Max.
Unit
Supply Voltage on VCC
-0.3
3.6
V
VIN
DC input on EN, C1, C2, C3, C4
-0.3
3.6
V
TX
RF Input Power. ANT0 and ANT1 terminated in
50Ω match
-
12.0
dBm
TA
Operating Temperature Range
0
85
°C
-40
150
°C
VCC
TSTG
Definition
Storage Temperature Range
Recommended Operating Conditions
Symbol
TA
VCC
Parameter
Min.
Typ.
Max.
Unit
Ambient temperature
-30
25
85
°C
VCC0, VCC1, VCC2 supply voltage
3.0
3.3
3.6
V
DC Electrical Characteristics
Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2603L-EK1 evaluation board
(de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
ICC-G
Total Supply Current
POUT = 17 dBm, 54 Mbps
OFDM signal, 64QAM
-
145
-
mA
ICC-B
Total Supply Current
POUT = 19 dBm, 11 Mbps
CCK signal, BT = 0.45
-
180
-
mA
ICQ
Total Supply Current
No RF
-
90
-
mA
Icntl
Control Line Current
C1, C2, C3 or C4 = 3.3V
1
10
μA
Icc0
Supply Current on VCC0
No RF, VCC0 = 3.3V
-
70
100
μA
No RF Applied, EN = R0 =
T0 = T1 = R1 = VCC0 = 0 V
-
1
10
μA
No RF Applied, EN = R0 =
T0 = T1 = R1 = 0 V; VCC0
= 3.3V
-
71
110
μA
ICC_OFF
Total Supply Current
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
5
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
PA Logic Characteristics
Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2603L-EK1 evaluation board
(de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
VENH
Logic High Voltage
(Module On)
-
1.8
3.3
3.6
V
VENL
Logic Low Voltage
(Module Off)
-
0
-
0.4
V
IENH
Input Current Logic
High Voltage
-
-
2
10
μA
IENL
Input Current Logic
Low Voltage
-
-
2
10
μA
Switch Logic Characteristics
Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2603L-EK1 evaluation board
(de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
VCTL_ON
VCTL_OFF
ON
OFF
CCTL
Parameter
Control Voltage
(On State)
Control Voltage
(OFF State)
Low Loss Switch
Control Voltage
High Loss Switch
Control Voltage
Control Input
Capacitance
Conditions
Min.
Typ.
Max.
Unit
-
3.0
-
3.6
V
-
0.0
-
0.2
V
2.7
-
3.6
V
0
-
0.3
V
-
-
100
pF
High State = VCTL_ON VCTL_OFF
Low State = VCTL_OFF VCTL_OFF
-
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
6
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Switch Control Logic Table
Switch Logic
Operational Mode
C1
C2
C3
C4
TX – ANT0
TX – ANT1
RX – ANT0
RX – ANT1
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
All other configurations
All switches set to OFF
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
7
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
AC Electrical Characteristics
802.11g/n Transmit Characteristics
Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2603L-EK1 evaluation board
(de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FIN
POUT
ACPR,
IEEE
Mask
Parameter
Condition
Min.
Typ.
-
2400
-
2500
MHz
Output Power
54 Mbps OFDM signal, 64
QAM, 3% EVM
-
17
-
dBm
Spectral Mask
POUT = 20 dBm, 11 Mbps
CCK, BT = 0.45
11 – 22 MHz
22 – 33 MHz
-
-
dBc
Frequency Range
-35
-55
Max.
Unit
P1dB
P1dB
-
-
23.0
-
dBm
S21
Small Signal Gain
-
24
27
30
dB
ΔS21
Small Signal Gain
Variation
Gain variation over single
40MHz channel
Gain Variation over band
-
3206 to 3312 MHz
-
-
15
dB
-
-50
-45
dBm/MHz
-
-50
-45
dBm/MHz
-
0.7
-
μs
10
14
-
dB
S213.2
Gain @ limit at Refvco spur frequency
2f
Harmonics
3f
tdr, tdf
Delay and rise/fall
Time
S11
Input Return Loss
STAB
RU
POUT = 19 dBm, 1 Mbps,
CCK
50 % of VEN edge and
90/10 % of final output
power level
-
0.5
dB
1.0
Stability
CW, POUT = 20 dBm
0.1 GHz – 20 GHz
Load VSWR = 6:1
All non-harmonically related outputs less than
-42 dBm/MHz
Ruggedness
PIN = 12dBm,
Load VSWR = 6:1
No permanent damage
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
8
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Receive Characteristics
Conditions: VCC = 3.3 V, EN = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2603L-EK1 evaluation
board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
FOUT
Frequency Range
-
2400
-
2500
MHz
RXIL
Insertion Loss
-
-
0.9
1.2
dB
RXRL
Return Loss
-
10
15
-
dB
-
-
0.5
dB
100
250
nSec
Delta Rx
Delta between Rx
paths
ANT0 to RX or
ANT1 to RX
Ton/off
T/R on/off
switching speed
Switching speed between T/R
modes. Vcc0=3.3V.
Tx to Rx Leakage
Device transmitting (EN = 3.3 V)
with 17.0 dBm. @ ANT0 or
ANT1, Power measured @ RX
TX ↔ ANT0 or ANT1 = ON,
RX ↔ ANT0 or ANT1= OFF
-
-3
0
dBm
Isolation between
ANT0 and ANT1
Difference in transmitted signal
level on ANT1 or ANT0 while
transmistting from ANT0 or
ANT1.
TX ↔ ANT0 or ANT1 = ON,
Rx and opposite ANT port
terminated in 50ohm.
18
25
-
dB
TRISO
ANTRISOL
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
9
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Power Detector Characteristics
Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2603L-EK1 evaluation board,
unless otherwise noted.
Symbol
Parameter
FOUT
Frequency Range
PDR
Power detect range,
CW
Condition
Min.
Typ.
-
2400
-
2500
MHz
0
-
21
dBm
-
1
-
kΩ
Measured at ANT0 or
ANT1
Max.
Unit
PDZsrc
DC source impedance
on PD_OUT
PDVNoRF
Output Voltage, POUT =
No RF
Measured into 1MΩ
-
0.12
-
V
PDVp18
Output Voltage, POUT =
17 dBm CW
Measured into 1MΩ
-
0.45
-
V
PDVp21
Output Voltage, POUT =
21 dBm CW
Measured into 1MΩ
-
0.75
-
V
LPF-3dB
Power detect low pass
filter -3dB corner
frequency
PDCLOAD = 390 pF
270
290
400
kHz
-
Figure 3: SE2603L Power Detector Characteristics
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
10
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Package Diagram
Figure 4: SE2603L Package Outline Drawing
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
11
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Recommended Land and Solder Patterns
Figure 5: Recommended Land and Solder Patterns
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
12
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Package Handling Information
Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed
regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption
may occur when the part is subjected to high temperature during solder assembly. The SE2603L is capable of
withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or
in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that
the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For
details on both attachment techniques, precautions, and handling procedures recommended, please refer to:
 “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045
 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044
 SiGe’s Application Note: “Class 0 ESD Device Handling”, Document Number QAD-00163
Caution! Class 0 ESD sensitive device
Branding Information
Pin 1 Designator
Pin 1
Terminal Finish
E3
Part
Lot Code
SiGe
2603L
Lot
Figure 6: SE2603L Branding and Pin 1 Location
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
13
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Tape and Reel Information
Parameter
Devices Per Reel
Reel Diameter
Tape Width
Value
3000
13 inches
12 millimeters
Figure 7: SE2603L-R Tape and Reel Information
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
14
DATA SHEET
SE2603L: 2.4 GHz High Efficiency Wireless LAN Front-End
Preliminary
Document Change History
Revision
Date
Notes
1.0
Sep 18, 2009
Created
1.1
Sep 23, 2009
Corrected operating voltage,
Updated current consumption
1.2
Sep 29, 2009
Remove reference to pull down resistor. Updated leakage current.
1.3
Oct 12, 2009
Updated package outline drawing
1.4
Jan 20, 2010
Updated for ESD
1.5
Jan 29, 2010
Removed reference to the incorrect part number
1.6
Jun 9, 2010
Updated MSL rating to MSL 1
1.7
Apr 10, 2012
Updated with Skyworks logo and disclaimer statement
Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein,
are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or
omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time,
without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other
difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials,
products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in
Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE,
INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL
SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR
OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT,
INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE
MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to
personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to
fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or
operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks.
Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated
published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries.
Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions,
posted at www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202436A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
15