Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Applications
Product Description



The SE2574BL-R is a complete 802.11 b/g WLAN
discrete power amplifier. The device provides all the
functionality of the power amplifier, power detector,
filter, associated input, inter-stage and output
matching in an ultra compact 2mm x 2mm x 0.9mm
form factor.
IEEE802.11b DSSS WLAN
IEEE802.11g,n OFDM WLAN
Embedded, SiP modules
Features








Dual Mode IEEE802.11b & IEEE802.11g
Integrated PA, digital bias control, 50Ω input and
output match, 3.2GHz TX Filter.
Integrated harmonic filter.
Integrated load insensitive Power Detector, with
<1dB error at 2:1 mismatch
21 dBm Output Power, 802.11b, 11 Mbps
18.5dBm @ 3.0 % EVM, 802.11g, 54 Mbps
2.3 V to 4.8 V direct to battery supply
Lead free, Halogen free, ROHS compliant ,
2 x2x0.9 mm QFN package, MSL 1
The SE2574BL-R is designed for ease of use, with all
the critical input and output matching integrated. The
SE2574BL-R includes a transmitter power detector
with 20 dB of dynamic range and a digital Enable for
power on/off control. Harmonic filters and an input
3.2GHz LO rejection filter are integrated on-chip. The
power ramp rise/fall time is 0.7 μs typical.
Ordering Information
Part No.
Package
Remark
SE2574BL-R
SE2574BL-R
SE2574BL-REK1
8 pin QFN
8 pin QFN
N/A
Samples
Tape and Reel
Evaluation kit
Functional Block Diagram
EN
VCC
VCC2
Bias Circuitry
RF IN
50ohm
Match
50ohm Match
& harmonic
Filter
3.2GHz
Filter
RF Out
Detector
Pdet
Figure 1: Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
1
DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Pin Out Diagram
Ground
Paddle
RF In
1
8 EN
GND
2
7 DET
GND
3
6 Vcc
RF Out
4
5 Vcc2
Figure 2: SE2574BL-R Pin Out (Top View Through Package)
Pin Out Description
Pin No.
Name
1
RF In
RF Input (No DC voltage on the pin, but DC short to ground)
2
GND
Ground
3
GND
Ground
4
RF Out
RF Output (No DC voltage on the pin, DC open to ground)
5
VCC2
Final Stage Supply Voltage (May attach directly to battery)
6
VCC
First Stage Supply Voltage (May attach directly to battery)
7
DET
Power Detector Output
8
EN
Die paddle
GND
Description
Power Amplifier Enable
Ground
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
2
DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage
to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions
defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected
workstations.
Symbol
Min.
Max.
Unit
Supply Voltage on VCC
-0.3
5.5
V
EN
DC input on EN
-0.3
4.0
V
TX
RF Input Power. ANT terminated in 50Ω match
-
12.0
dBm
TA
Operating Temperature Range
-40
85
°C
Storage Temperature Range
-40
150
°C
1000
V
VCC
TSTG
ESDHBM
Definition
JEDEC JESD22-A114, all pins
Recommended Operating Conditions
Symbol
TA
VCC
Parameter
Min.
Typ.
Max.
Unit
Ambient temperature
-40
25
85
°C
Supply voltage, nominal operation
2.7
3.3
5.0
Supply voltage, output power reduced by 2dB
typ
2.3
2.7
V
DC Electrical Characteristics
Conditions: VCC = 3.3V , EN = 3.3V, TA = 25 °C, as measured on Skyworks SE2574BL-R-EK1 evaluation board, all
unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
-
mA
-
mA
ICC-G
Total Supply Current
54 Mbps OFDM signal, 64QAM
18dBm, VCC = 3.3V
-
ICC-B
Total Supply Current
11 Mbps CCK signal, BT = 0.45
20dBm, VCC = 3.3V
-
ICQ
Total Supply Current
No RF
-
110
-
mA
ICC_OFF
Total Supply Current
EN = 0 V, No RF Applied
-
1
10
μA
VCC = 3.3V
140
165
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
3
DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Logic Characteristics
Conditions: VCC = 3.3V , EN = 3.3V, TA = 25 °C, as measured on Skyworks SE2574BL-R-EK1 evaluation board, all
unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
VENH
Logic High Voltage
(Module On)
-
1.8
-
3.6
V
VENL
Logic Low Voltage
(Module Off)
-
0
-
0.4
V
IENH
Input Current Logic
High Voltage
-
-
160
180
μA
IENL
Input Current Logic
Low Voltage
-
-
20
25
μA
AC Electrical Characteristics
802.11g/n Transmit Characteristics
Conditions: VCC = 3.3V , EN = 3.3V, TA = 25 °C, as measured on Skyworks SE2574BL-R-EK1 evaluation board, all
unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FIN
Pout
Parameter
Condition
Min.
Typ.
-
2400
-
2500
54 Mbps OFDM , 64 QAM, EVM=3%
-
18.5
-
Frequency Range
Output Power, 3.3V
P1dB
P1dB
VCC = 3.3V
S21
Small Signal Gain
-
ΔS21
Small Signal Gain
Variation
Gain variation over single 20MHz
channel
Gain Variation over band
Harmonics
1 Mbps, BPSK,
2f
3f
S11
STAB
RU
Unit
MHz
dBm
11Mbps, CCK, BT=0.45, Mask
tdr, tdf
Max.
21
-
25.0
-
dBm
25
27
29
dB
-
0.5
-
-
-
1.1
20dBm, 3.3V
-
-40
-35
dBm/MHz
20dBm, 3.3V
-
-40
-35
dBm/MHz
-
0.7
-
μs
10
15
-
dB
dB
Delay & rise/fall Time
50 % of VEN edge and 90/10 % of
final output power level
Input Return Loss
-
Stability
CW, POUT = 20 dBm, VCC = 3.3V
0.1 GHz – 20 GHz
Load VSWR = 10:1
All non-harmonically related outputs less
than -42 dBm/MHz
Ruggedness
PIN = 12dBm, VCC = 3.3V
Load VSWR = 10:1
No permanent damage
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
4
DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Power Detector Characteristics
Conditions: VCC = 3.3V, EN = 3.3V, TA = 25 °C, as measured on Skyworks SE2574BL-R-EK1 evaluation board, all
unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
FOUT
Frequency Range
PDR
Power detect range, CW
PDZsrc
DC source impedance on
PD_OUT
Condition
Measured at ANT
-
VCC = 3.3V
Unit
Min.
Typ.
Max.
2400
-
2500
MHz
0
-
23
dBm
-
1
-
kΩ
Output Voltage,
POUT = No RF
Measured into 1MΩ
-
0.10
-
V
PDVp16
Output Voltage,
POUT = 16 dBm CW
Measured into 1MΩ
-
0.50
-
V
PDVp19
Output Voltage,
POUT = 19 dBm CW
Measured into 1MΩ
-
0.70
-
V
PDVp22
Output Voltage,
POUT = 22 dBm CW
Measured into 1MΩ
-
1.0
-
V
LPF-3dB
Power detect low pass filter
-3dB corner frequency
Measured into 1MΩ
PDVNoRF
2.5
MHz
Figure 3: SE2574BL-R Power Detector Characteristics
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
5
DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Package Diagram
This package is Pb free and RoHS compliant. The product is rated MSL1.
1
8
8
1
2
7
7
2
3
6
6
3
4
5
5
4
TOP VIEW
BOTTOM VIEW
Figure 4: SE2574BL-R Package Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
6
DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Recommended Land Pattern
1
8
1
8
1
8
2
7
2
7
2
7
3
6
3
6
3
6
4
5
4
5
4
5
Figure 5: SE2574BL-R Package Diagram
Branding Information
Pin 1
Part
Lot Code
574B
Lot
Figure 6: SE2574BL-R Branding and Pin 1 Location (Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
7
DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Package Handling Information
Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed
regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption
may occur when the part is subjected to high temperature during solder assembly. The SE2574BL-R is capable of
withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or
in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that
the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For
details on both attachment techniques, precautions, and handling procedures recommended by Skyworks, please
refer to:


Skyworks Application Note: “QFN solder reflow and rework information application note”, Document Number
QAD-00045
Skyworks Application Note: “Handling, packing, shipping and use of moisture sensitive QFN application note”,
Document Number QAD-00044
Tape and Reel Information
Parameter
Devices Per Reel
Reel Diameter
Tape Width
Value
3000
7 inches
8 millimeters
Figure 8: SE2574BL-R Tape and Reel Information
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
8
DATA SHEET
SE2574BL-R: 2.4 GHz 802.11b/g/n Power Amplifier
Document Change History
Revision
Date
Notes
1.0
February-10-2011
Created
1.1
February-24-2011
Updated POD
1.2
April-28-2011
Updated Part marking and updated specification
1.3
December-16-2011
Updated specifications
1.4
February-27-2012
Updated Tape and reel information.
Copyright © 2013 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein,
are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or
omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time,
without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other
difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials,
products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in
Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE,
INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL
SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR
OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT,
INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE
MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to
personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to
fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or
operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks.
Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated
published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries.
Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions,
posted at www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202675A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 21, 2013
9