Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Applications
Product Description



The SE5511T is a complete 802.11n WLAN RF frontend module providing all the functionality of the power
amplifiers, LNA, power detector, Antenna switches,
filtering and associated matching. The SE5511T
provides a complete 2.4 GHz and 5 GHz WLAN RF
solution from the output of the transceiver to the
antennas in a compact form factor.
IEEE802.11b DSSS WLAN
IEEE802.11a,g,n OFDM WLAN
Embedded applications with Bluetooth (Mobile)
Features







All RF ports matched to 50 Ω
Integrated 2.4,5 GHz PA, 5 GHz LNA, SP3T,
SP2T switches and filtering
Integrated Power Detector
19.5 dBm @ 3 % EVM, 802.11g, 54 Mbps
18 dBm @ 3 % EVM, 802.11a, 54 Mbps
Lead free, Halogen Free and RoHS compliant
Compact package, 3 x 4 x 0.6 mm, MSL 1
Ordering Information
Part No.
Package
Remark
SE5511T
SE5511T-R
SE5511T-EK1
28 pin QFN
28 pin QFN
N/A
Samples
Tape & Reel
Evaluation kit
The receive path is designed to maximize
performance by providing both a 5 GHz Low noise
amplifier with bypass mode, for use when high power
signals are being received.
Designed for ease of use, all RF ports are matched to
50 Ω to simplify PCB layout and the interface to the
transceiver RFIC. The SE5511T also includes a
transmitter power detector for each band with 20 dB
of dynamic range.
Functional Block Diagram
CRX2
CBT
PEN2
TX2
2.4 GHz PA
RX2
DET
ANT2
pwr
det
RX5
5.4 GHz LNA
TX5
ANT5
5.4 GHz PA
CRX5
LEN5
BT
PEN5
Figure 1: Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
1
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Pin Out Diagram
TX2
VCC2
GND
DNC
CSP5
PEN5
VCC3
GND
CRX5
28
27
26
25
24
23
22
21
20
CSP2
1
19
CRX2
RX2
2
18
ANT2
3
17
RX5
4
16
ANT5
VCC1
5
15
CBT
GND
PEN2
12
13
14
BT
VCC4
11
GND
10
LEN5
9
DET
8
VCC5
TX5
7
GND
6
GND
Figure 2: SE5511T Pin Out (Top View Through Package)
Pin Out Description
Pin No.
Name
1
CSP2
Description
Pin No.
Name
Description
2.4 GHz PA bias speed-up
16
ANT5
5 GHz Antenna port
2
RX2
2.4 GHz Receive port
17
GND
Ground
3
GND
Ground
18
ANT2
2.4 GHz Antenna port
4
RX5
5 GHz Receive port
19
CRX2
Control for 2.4 GHz Receive
5
VCC1
Power Supply
20
CRX5
Control for 5 GHz Receive
6
TX5
5 GHz Transmit port
21
GND
Ground
7
GND
Ground
22
VCC3
8
VCC5
Power Supply
23
PEN5
9
VCC4
24
CSP5
10
PEN2
25
DNC
Do Not Connect
11
DET
26
GND
Ground
12
LEN5
Power Supply
Enable for 2.4 GHz PA and
Transmit Switch
Power Detector Output
Enable for 5 GHz LNA and
Receive Switch
Ground
Power Supply
Enable for 5 GHz PA and
Transmit switch
5 GHz PA bias speed-up
27
VCC2
Power Supply
28
TX2
13
GND
14
BT
15
CBT
2.4 GHz Transmit port
Bluetooth Port
Control for Bluetooth port
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
2
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage
to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions
defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected
workstations.
Symbol
Definition
Min.
Max.
Unit
VCC
Supply Voltage
-0.3
5.5
V
VIN
Control Pin Voltages
-0.3
3.6
V
-
+10
dBm
Operating Temperature Range
-40
85
°C
Storage Temperature Range
-40
150
°C
TXRFIN
TA
TSTG
ESD HBM
TX2/TX5, with ANT2/ANT5 terminated in 50Ω
JEDEC JESD22-A114
All pins
V
1000
Recommended Operating Conditions
Symbol
Parameter
Min.
Typ.
Max.
Unit
VCC
Supply Voltage
2.97
3.3
3.6
V
TA
Ambient Temperature
-40
25
85
°C
Control Logic Characteristics
Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5511T-EK1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
3
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Parameter
min
nom
max
Units
Logic input high : VIH
1.4
Vcc+0.3
upto 3.6
V
Logic input low : VIL
0
0.3
V
All control pins except CRX2, CRX5
1
µA
CRX2, CRX5
50
Logic input current : IIH
Logic input current : IIL
µA
All control pins except CRX2, CRX5
1
CRX2, CRX5
20
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
4
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
DC Electrical Characteristics
Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5511T-EK1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted
Symbol
Parameter
Conditions
Min.
Total 802.11g Transmit Supply
Current
POUT = 20 dBm, 54 Mbps OFDM
signal, 64QAM, PEN2 = Hi,
POUT = 18 dBm, 54 Mbps OFDM
signal, 64QAM, PEN2 = Hi,
TXICQ-G
Quiescent current , 802.11g
Transmit supply Current
No RF applied, PEN2=Hi
-
TXICC-A
Total 802.11a Transmit Supply
Current
POUT = 18 dBm, 54 Mbps OFDM
signal, 64QAM, PEN5= Hi
POUT = 16 dBm, 54 Mbps OFDM
signal, 64QAM, PEN5= Hi
-
TXICC-G
TXICQ-A
Quiescent current , 802.11a
Transmit supply Current
No RF applied, PEN5- Hi
RXICC-A
Total 802.11a Receive Supply
Current
CRX5 = Hi, LEN= Hi
CRX5 = Hi, LEN = Lo
RXICC-G
Total 802.11g Receive Supply
Current
CRX2 = Hi
Total BT Supply Current
CBT = Hi
Total Supply Current
No RF,
PEN2=PEN5=CRX2=CRX5=CBT
=LEN5=0V
ICC-BT
ICC_OFF
Typ.
Max.
Unit
215
-
mA
185
120
-
mA
230
mA
210
-
155
-
10
0.25
mA
0.25
mA
-
0.25
mA
-
5
μA
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
-
mA
5
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Operating Modes
Mode#
Mode Description
PEN2
PEN5
LEN5
CRX2
CRX5
CBT
0
All Off
0
0
0
0
0
0
1
BT
0
0
0
0
0
1
2
BT + RX5(Low gain)
0
0
0
0
1
1
3
BT + RX5(High gain)
0
0
1
0
1
1
4
BT + TX5
0
1
0
0
0
1
5
RX2 + RX5(Low gain)
0
0
0
1
1
0
6
RX2 + RX5(High gain)
0
0
1
1
1
0
7
TX2
1
0
0
0
0
0
8
TX5
0
1
0
0
0
0
9
RX2
0
0
0
1
0
0
10
RX5 (Low Gain)
0
0
0
0
1
0
11
RX5 (High Gain)
0
0
1
0
1
0
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
6
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
AC Electrical Characteristics
2.4 GHz Transmit Characteristics
Conditions: VCC = 3.3 V, PEN2= Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5511T-EK1 evaluation
board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FIN
POUT
S21
S21_OOB
∆S21
Parameter
Condition
Min.
Typ.
-
2400
-
18.5
19.5
18
dBm
27.5
dB
Frequency Range
Output Power, 54
Mbps OFDM, 64 QAM
EVM=3%
EVM=2.5%
Gain
2400 – 2500 MHz
Out of Band Gain
<2170 MHz
Gain Variation
Over band
Unit
2500
MHz
19
dB
1.5
S11
Input Return Loss
-10
S22
Output Return Loss
-10
NF
Noise Figure
10
2f
Max.
dBpp
dB
-5
dB
dB
2f @ Pout= 22 dBm
-35
-25
3f
3f @ Pout = 22 dBm
-35
-30
ACP11b
Spectral Mask
11b @ Pout=22 dBm:
fc +/- 11 MHz
fc +/- 22 MHz
Stability
POUT ≤ 23dBm
Load VSWR = 4:1
Enable time
10% to 90% of TX RF
power, from time that
PEN2 is at 50%
11b Harmonics
STAB
TEN
dBm/MHz
dBc
-34
-54
-32
-52
All non-harmonically related outputs less than
-45 dBm/MHz
800
nsec
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
7
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
2.4 GHz Receive Characteristics
Conditions: VCC = 3.3V, CRX2 = Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5511T-EK1 evaluation
board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FOUT
RX2IL
S11
ISOLSW
IP1dB
TEN
Parameter
Condition
Min.
-
2400
-
Insertion Loss
CRX2= Hi
-
1.0
dB
RX2 Port Return Loss
CRX2= Hi
-
-14
dB
ANT2-RX2, PEN2=Hi
26
CRX2= Hi
15
10% to 90% of RX RF
power, from time that
CRX2 is at 50%
-
Frequency Range
Switch Isolation
Input P1dB
Enable Time
Typ.
Max.
2500
-
Unit
MHz
dB
dBm
-
800
nsec
Bluetooth Characteristics
Conditions: VCC = 3.3 V, CBT= Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5511T-EK1 evaluation board
(de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
Condition
Min.
Typ.
-
2400
-
FOUT
Frequency Range
BTIL
Insertion Loss
CBT= Hi
-
1.0
S11
BT Port Return Loss
CBT= Hi
-
-14
ANT2-BT, PEN2=Hi
20
-
CBT= Hi
15
10% to 90% of BT RF
power, from time that CBT
is at 50%
-
ISOLSW
IP1dB
TEN
Switch Isolation
Input P1dB
Enable Time
Max.
2500
Unit
MHz
dB
dB
-
dB
dBm
-
800
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected]sinc.com • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
nsec
8
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
5 GHz Transmit Characteristics
Conditions: VCC = 3.3 V, PEN5= Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5511T-EK1 evaluation
board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FIN
POUT
S21
∆S21
Parameter
Condition
Min.
Typ.
-
4900
-
17.0
18
16
dBm
28
dB
Frequency Range
Output Power, 54
Mbps OFDM, 64 QAM
EVM=3%
EVM=2.5%
Gain
Gain Variation
Max.
5850
Over 40 MHz Channel
S11
Input Return Loss
-14
S22
Output Return Loss
-10
2f
Harmonics @ Pout=18
dBm
dBpp
-10
dB
-5
dB
-40
-50
-35
-42
3f
3f @ Pout = 18 dBm
-50
-45
ACP11a
Spectral Mask
11a @ Pout=18 dBm:
fc +/- 11 MHz
fc +/- 20 MHz
fc +/- 30 MHz
Stability
POUT ≤ 21dBm
Load VSWR = 4:1
Enable Time
10% to 90% of TX RF
power, from time that
PEN5 is at 50%
MHz
1.5
2f (5150-5300 MHz)
2f (5300-5850 MHz)
TEN
Unit
dBm/MHz
dBc
-23
-30
-43
-20
-28
-40
All non-harmonically related outputs less than
-45 dBm/MHz
-
-
800
nsec
5 GHz Receive Characteristics
Conditions: VCC = 3.3 V, LEN5= Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5511T-EK1 evaluation
board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
FOUT
Frequency Range
S21
Gain
NF
IP1dB
Condition
Min.
Typ.
-
4900
-
dB
LEN5 = Lo
-7
dB
dB
-
2.5
Input P1dB
LEN5= Hi
LEN5=Lo
-8
+5
-6
+7
-
-10
-
-
TEN
Enable Time
MHz
12
LEN5=Hi
Input Return Loss
5900
Unit
LEN5 = Hi
Noise Figure
S11
Max.
10% to 90% of RX RF
power, from time that
-
dBm
dB
800
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
nsec
9
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
LEN5 is at 50%
Power Detector Characteristics
Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5511T-EK1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
FOUT
Frequency Range
PDR
Power detect range,
peak power
PDZLOAD
DC load impedance
PDVP23
Output Voltage, POUT =
23 dBm
PDVP19
Output Voltage, POUT =
19 dBm
PDVpnoRF
Output Voltage, POUT =
No RF
PDVAR
Power Detector
Accuracy vs Load
VSWR
Condition
Min.
Typ.
PEN2= Hi
PEN5 = Hi
2400
4900
-
2500
5900
MHz
0
-
23
dBm
-
2.5
Measured at ANT
PEN2= Hi
Max.
Unit
kΩ
0.8
1.0
V
PEN5= Hi
4950 MHz
5150-5850 MHz
0.4
0.5
0.8
1.0
V
-
-
-
V
+0.6
dB
Pout=20 dBm, 2:1 load
VSWR, any angle
-1
0.125
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
10
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Package Diagram
28
27
26
25
24
23
22
21
20
20
21
22
23
24
25
26
27
28
1
19
19
1
2
18
18
2
3
17
17
3
4
16
16
4
5
15
15
5
6
7
8
9
10
11
13
12
14
14
13
12
11
10
9
8
7
6
TOP VIEW
BOTTOM VIEW
Figure 3: Package Outline Drawing
Branding Information
Pin 1 Identifier
Terminal Finish
Pin 1
e3
Part Number
Lot Code
SiGe
SE5511T
Lot Code
Figure 4: SE5511T Branding Information
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
11
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Recommended PCB Footprint
28
27
26
25
24
23
22
21
20
27
1
19
2
18
3
17
4
16
5
15
21
3
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
17
7
28
27
13
26
25
24
23
22
21
20
1
19
1
19
2
18
2
18
3
17
3
17
4
16
4
16
5
15
5
15
6
7
8
9
10
11
12
13
14
6
7
8
9
10
11
12
13
14
Figure 5: Recommended PCB footprint
Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed
regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption
may occur when the part is subjected to high temperature during solder assembly. The SE5511T is capable of
withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or
in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that
the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For
details on both attachment techniques, precautions, and handling procedures recommended, please refer to:
 “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045.
 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
12
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Tape and Reel Information
Parameter
Devices Per Reel
Reel Diameter
Tape Width
Value
3000
13 inches
12 millimeters
Figure 6: SE5511T-R Tape and Reel Information
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
13
DATA SHEET
SE5511T: Dual Band 802.11n WLAN/BT Front End
Document Change History
Revision
Date
Notes
1.0
August-04-2010
Created
1.1
April-07-2011
Updated Functional block diagram
1.2
June-09-2011
Updated specifications
1.3
July-06-2011
Updated RX2 isolation specification
1.4
November-22-2011
Updated specifications
1.5
February-03-2012
Updated temperature range, updated tape and reel info
1.6
April-11-2012
Updated with Skyworks logo and disclaimer statement
1.7
August-14-2012
Updated recommended pcb footprint
Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein,
are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or
omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time,
without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other
difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials,
products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in
Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE,
INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL
SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR
OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT,
INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE
MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to
personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to
fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or
operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks.
Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated
published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries.
Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions,
posted at www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202403A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012
14