Signal Isolated Amplifier Module Thermal Resistance Isolation Transmitter Features: ● Three-wire,four-wire or two-wire PT100 thermal resistance signal input ● Accuracy, Linearization error grade:0.2 ● Linearization disposal and long line compensate circuit ● Isolation Voltage: 3000VDC input/power/output ● Power：5V、12V、15V or 24VDC ● International standard signal output：4-20mA/0-5V/0-10V etc. ● Small size,low cost ●Standard DIP 24 Pin,UL94V-0 fire ● Industrial temperature range: - 45 ~ + 85 ℃ Application: ●PLC/DCS systemic temperature signal isolation, acquisition. ●Industrial high accuracy temperature measurement ●Thermal resistance signa isolation and temperature control ●Ground-loop elimination ●Temperature sensor signal converter to standard signal ●Oil temperature measurement and alarm ●No distortion in long distance signal transmission ●Electric supervision,medical application and safe isolated bar. Description: ISO W-Z Series is a mixed integrate circuit that thermal resistance signal as temperature high/low isolation converter to linearity standard signal to temperature.It integrated a set of isolated DC/DC converters, Linearization disposal and long line compensate circuit,can bring two group of each other isolated power to input port for magnifying circuit,modulating circuit powered and output port demodulation.They can meet industrial wide temperature,humidity,shaky poor operation condition. Figure 1 ISO Z-Wseries wiring diagram Signal Isolated Amplifier Module Operation Range(max) If over above range,maybe cause products damaged permanently. Continue isolation voltage value 3000VDC Power Vin range: ±10%Vin Jointing temperature(10sec.) +300℃ Vout signal load(MIN) 2KΩ Part number and description: ISO Z□ - W□ - Type Z1: Pt100 Z2: Pt10 Z3: Cu100 Z4: Cu50 Input T Range W1: -20-100℃ W2: 0-100℃ W3: 0-150℃ W4: 0-200℃ W5: 0-400℃ W6: User-defined Power Supply P1: DC24V P2: DC12V P3: DC5V P4: DC15V P5: User-defined Output Signal O1: 4-20mA O2: 0-20mA O4: 0-5V O6: 1-5V O7: User-defined P□ - O□ O5: 0-10V Examples: 1. signal Input: Pt100,temperature range:0~100℃; signal output:4-20mA; power:24V Part No.: 2. ISO Z1-W1-P1-O1 signal input: Cu50,temperature range:0~100℃;signal output:0-5V;power:12V Part No.: ISO Z4-W2-P2-O4 Technic parameter: Parameter Test Condition Isolated voltage 1min Mix 1500 Non-linearity(to temperature) Type Max 3000 Unit VDC 0.2 0.5 %FSR 10 V Output Voltage 5 signal Current 20 mA 10 mS kΩ Frequency response Load Voltage Vout=10V 2 capability current Iout=20mA 500 No-filter 10 mV 50 ppm/℃ Signal output ripple Signal temperature drift Assistant power Voltage User-defined current VD=12V 3.3 12 42 650 24 Ω VDC mA Signal Isolated Amplifier Module Power loss 0.3 Operating temperature Storage temperature 0.5 1 W -45 85 ℃ -55 125 ℃ Physical Dimensions and Pin Description: (Figure 1) Voltage output : ZA1 ZA2 FB1 FB2 VD GND Vo+ NC Vo- NC B B A 1 2 3 4 6 7 10 11 12 13,14,15,21 22 23 24 Current output: ZA1 ZA2 FB1 FB2 VD GND NC Io- NC Io+ NC B B A 1 2 3 4 6 7 10,11,12 13 14 15 21 22 23 24 Note:1.all NC can not connect any external circuit. 2.Two wire signal input,PIN 22,23(input B) connect,four wires signal input,PIN 24 connects to any port of A. 3.Broken line test: a.output max. value:the line that connecting PIN22,23 is broken. b. output min. value:the line that connecting PIN23 is broken. ISO Size and PCB dimension(DIP 24) Top View