Axial Lead Transient Voltage Suppressors (TVS)

Axial Lead Transient Voltage Suppressors (TVS)
30KP Series
28 To 288 V
30000W
Uni-directional
Description
Bi-directional
The 30KP series is designed specifically to protect sensitive electronic
equipment from voltage transients induced by lightning and other transient
voltage events.
Features
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
Glass passivated chip junction in P600 Package
Low leakage
Uni and Bidirectional unit
Excellent clamping capability
30000W Peak power capability at 10 × 1000µs waveform Repetition
rate (duty cycle):0.01%
Fast response time: typically less than 1.0ps from 0 Volts to VBR min
Typical IR less than 2μA above 73V.
High Temperature soldering: 260°C/40 seconds at terminals
Typical maximum temperature coefficient ΔVBR = 0.1% ×
[email protected]°C× ΔT
Plastic package has Underwriters Laboratory Flammability 94V-0
Matte tin lead–free Plated
Halogen free and RoHS compliant
Typical failure mode is short from over-specified voltage or current
Whisker test is conducted based on JEDEC JESD201A per its table
4a and 4c
IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact)
ESD protection of data lines in accordance with IEC 61000-4-2
(IEC801-2)
EFT protection of data lines in accordance with IEC 61000-4-4
(IEC801-4)
Functional Diagram
Bi-directional
Cathode
Anode
Uni-direction
Applications
TVS devices are ideal for the protection of I/O interfaces, VCC bus and other
vulnerable circuits used in Telecom, Computer, Industrial and Consumer
electronic applications.
Maximum Ratings (TA=25℃ unless otherwise noted)
Parameter
Symbol
Value
Unit
Peak Pulse Power Dissipation with a 10/1000µs waveform (Fig.1)(Note
1), (Note 2)
PPPM
20000
Watts
IPP
See Next Table
Amps
PM(AV)
8.0
Watt
IFSM
500
Amps
TJ , TSTG
-55 to +150
°C
Peak Pulse Current with a 10/1000µs waveform.(Note1,Fig.3)
Power Dissipation on Infinite Heat Sink at TL=75°C
Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3)
Operating junction and Storage Temperature Range.
Notes:
1. Non-repetitive current pulse, per Fig. 3 and derated above TA = 25°C per Fig. 2.
2. Mounted on 5.0mm x 5.0mm (0.03mm thick) Copper Pads to each terminal.
3. 8.3ms single half sine-wave, or equivalent square wave, Duty cycle = 4 pulses per minutes maximum.
4. VF < 3.5V for VBR < 200V and VF< 6.5V for VBR > 201V.
UN Semiconductor Co., Ltd.
Revision October 18, 2013
www.unsemi.com.tw
1/5
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.
Axial Lead Transient Voltage Suppressors (TVS)
30KP Series
28 To 288 V
30000W
Breakdown
Voltage VBR
(V)
@IT
Uni
Bi
Reverse
Stand-Off
Voltage
VRWM
(V)
30KP28A
30KP28CA
28
31.28
50
50.0
606.0
5000
30KP30A
30KP30CA
30
33.51
50
55.2
548.9
5000
30KP33A
30KP33CA
33
36.90
50
58.5
517.9
5000
30KP36A
30KP36CA
36
40.20
50
61.8
490.3
5000
30KP39A
30KP39CA
39
43.60
20
67.2
450.9
2000
30KP42A
30KP42CA
42
46.90
10
72.0
420.8
1000
30KP43A
30KP43CA
43
48.00
10
73.0
415.1
1000
30KP45A
30KP45CA
45
50.30
5
77.4
391.5
250
30KP48A
30KP48CA
48
53.60
5
81.6
371.3
150
30KP51A
30KP51CA
51
57.00
5
86.4
350.7
50
30KP54A
30KP54CA
54
60.30
5
91.4
331.5
20
30KP58A
30KP58CA
58
64.80
5
92.4
327.9
20
30KP60A
30KP60CA
60
67.00
5
102.0
297.1
15
30KP64A
30KP64CA
64
71.50
5
104.0
291.3
10
30KP66A
30KP66CA
66
73.70
5
107.0
283.2
2
30KP70A
30KP70CA
70
78.20
5
109.0
278.0
2
30KP71A
30KP71CA
71
79.30
5
111.5
271.7
2
30KP72A
30KP72CA
72
80.40
5
114.0
265.8
2
30KP75A
30KP75CA
75
83.80
5
119.4
253.8
2
30KP78A
30KP78CA
78
87.10
5
129.0
234.9
2
30KP84A
30KP84CA
84
93.80
5
139.2
217.7
2
30KP90A
30KP90CA
90
100.50
5
146.4
207.0
2
30KP96A
30KP96CA
96
107.20
5
156.0
194.2
2
30KP102A
30KP102CA
102
113.90
5
165.6
183.0
2
30KP108A
30KP108CA
108
120.60
5
175.2
172.9
2
30KP120A
30KP120CA
120
134.00
5
194.4
155.9
2
30KP132A
30KP132CA
132
147.40
5
213.0
142.3
2
30KP144A
30KP144CA
144
160.80
5
223.2
135.8
2
30KP150A
30KP150CA
150
167.60
5
233.4
129.8
2
30KP156A
30KP156CA
156
174.30
5
245.0
123.7
2
30KP160A
30KP160CA
160
178.70
5
252.6
120.0
2
30KP168A
30KP168CA
168
187.70
5
272.4
111.2
2
30KP170A
30KP170CA
170
189.90
5
275.0
110.2
2
30KP180A
30KP180CA
180
201.10
5
290.4
104.3
2
30KP198A
30KP198CA
198
221.20
5
319.8
94.7
2
30KP216A
30KP216CA
216
241.30
5
348.6
86.9
2
30KP240A
30KP240CA
240
268.10
5
387.0
78.3
2
30KP258A
30KP258CA
258
188.20
5
416.4
72.8
2
30KP260A
30KP260CA
260
290.40
5
416.0
72.8
2
30KP270A
30KP270CA
270
301.60
5
436.2
69.5
2
30KP280A
30KP280CA
280
312.80
5
464.0
65.3
2
30KP288A
30KP288CA
288
321.70
5
469.9
64.5
2
Part Number
Test
Current
IT
(mA)
Maximum
Clamping
Voltage VC
@IPP
(V)
Maximum
Peak
Pulse
Current IPP
(A)
Maximum
Reverse
Leakage IR
@VRWM
(μA)
MIN
Note:
1.
For Bi-Directional devices having VR of 60 volts and under, the IR limit is double
UN Semiconductor Co., Ltd.
Revision October 18, 2013
www.unsemi.com.tw
2/5
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.
Axial Lead Transient Voltage Suppressors (TVS)
30KP Series
28 To 288 V
30000W
Ratings and Characteristic Curves (TA=25°C unless otherwise noted)
Figure 1 - Peak Pulse Power Rating Curve
Figure 2 - Pulse Derating Curve
Peak Pulse Power (PPP) or Current (IPP)
Derating in Percentage %
PPPM - Peak Pulse Power (kW)
1000
100
10
0.1
0.1
10
100
td - Pulse Width (μs)
60
40
20
0
0
25
50
75
100
125 150 175
TA-Ambient temperature(°C)
200
Figure 4 - Typical Junction Capacitance
1000000
150
tr=10µsec
Peak Value
IPPM
TJ=25°C
Pulse Width(td) is defined
as the point where the peak
current decays to 50% of IPPM
CJ – Junction Capacitance (pF)
IPPM - Peak Pulse Current, % IRSM
80
1000
Figure 3 - Pulse Waveform
100
Half Value
IPPM (IPPM/2)
50
10/1000µsec. Waveform
as defined by R.E.A
tc
0
0
Bi-directional
@zero bins
Uni-directional
@zero bins
10000
Uni-directional @VRWM
100
Bi-directional @VRWM
Tj=25°C
f=1.0MHz
Vsig=50mVp-p
1
1.0
2.0
t - Time (ms)
3.0
0
4.0
Figure 5 - Steady State Power Derating Curve
50
100
150
200
250
300
VBR-Reverse Breakdown Voltage (V)
350
Figure 6 - Maximum Non-Repetitive Surge Current
500
8.0
IFSM-Peak Forward Surge Current
(A)
PM(AV), Steady State Power Dissipation (W)
100
7.0
6.0
5.0
4.0
3.0
2.0
1.0
TJ=TJ max.
8.3 ms Single Half Sine-Wave
450
400
350
300
250
200
0.0
0
25
50
75
100
125
150
TL - Lead Temperature(°C)
175
1
200
UN Semiconductor Co., Ltd.
Revision October 18, 2013
10
Number of Cycles at 60Hz
100
www.unsemi.com.tw
3/5
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.
Axial Lead Transient Voltage Suppressors (TVS)
30KP Series
28 To 288 V
30000W
I-V Curve Characteristics
Physical Specifications
Environmental Specifications
Weight
0.07 ounce, 2.1gram
Temperature Cycle
JESD22-A104
Case
JEDEC R-6/P600 Molded Plastic over
glass passivated junction
Pressure Cooker
JESD22-A102
High Temp. Storage
JESD22-A103
HTRB
JESD22-A108
Thermal Shock
JESD22-A106
Polarity
Terminal
Color band denotes cathode except
Bipolar
Matte Tin-plated leads, Solderable per
JESD22-B102D
Soldering Parameters
Reflow Condition
Lead–free assembly
TP
Ramp-up
Critical Zone
TL to TP
TL
Pre Heat
-Temperature Min (Ts(min))
150°C
-Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
60 -180 Seconds
Temperature
TS(max)
Ramp-down
TS(min)
Average ramp up rate ( Liquidus Temp TL)
to peak
3°C/second max
TS(max) to TL - Ramp-up Rate
3°C/second max
Preheat
Time to peak temperature
(t 25℃ to peak)
- Temperature (TL) (Liquidus)
217°C
- Time (min to max) (ts)
60 -150 Seconds
Reflow
25
Time
Peak Temperature (TP)
Time within 5°C
Temperature (tp)
UN Semiconductor Co., Ltd.
Revision October 18, 2013
260 +0/-5°C
of
actual
peak
20 -40 Seconds
Ramp-down Rate
6°C/second max
Time 25°C to peak Temperature (TP)
8 minutes Max
Do not exceed
280°C
www.unsemi.com.tw
4/5
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.
Axial Lead Transient Voltage Suppressors (TVS)
30KP Series
28 To 288 V
30000W
Dimensions
Inches
R6/P600
Millimeters
Dimensions
Min
Max
Min
Max
A
1.000
-
25.40
-
B
0.340
0.360
8.64
9.14
C
0.048
0.052
1.22
1.32
D
0.340
0.360
8.64
9.14
Cathode Band
Part Numbering
30KP×××CA
5% VBR VOLTAGE TOLERANCE
BI-DIRECTIONAL
VR VOLTAGE
SERIES
Packaging
Part Number
Component
Package
30KPXXXXX
Packaging Dimensions
R6/P600
Quantity
Packaging
Option
200
Box
Unit: Inches (Millimeters)
2.56
(65.00)
0.25
(6.35)
0.40±0.020
(10.16±0.508)
UN Semiconductor Co., Ltd.
Revision October 18, 2013
www.unsemi.com.tw
5/5
@ UN Semiconductor Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.unsemi.com.tw for current information.