SC220 x SC220Q 20MHz, 650mA, X-EMI™-Enabled Synchronous Step-Down Regulator POWER MANAGEMENT Features Description Patented X-EMITM Inductor Technology Enables Trace Inductors in PC Board Material Excellent EMI Performance Efficiency up to 90% 19µA Quiescent Current under Very Light Loads Wide Input Voltage Range — 2.7V to 5.5V Adjustable Output Voltage Down to 1.0V Output DC Current — up to 650mA High Light-load Efficiency via Automatic PSAVE Mode Ultra-fast Transient Response — <1µs Temperature Range — -40 to +85°C Shutdown Current — 0.1µA (typical) Requires Tiny 220nH Inductor Requires Only 1μF of Output Capacitance External Switching Frequency Synchronization Protection Features Including Over-Current Protection Output Short-Circuit Protection Thermal Shutdown Protection Offered in SOIC 8 Lead Package Lead-free, Halogen-free, and RoHS/WEEE Compliant AEC-Q100 Qualified Version Available The SC220/Q is a 20MHz X-EMI™(1)-enabled step-down regulator optimized for power low voltage rails from 2.7 to 5.5V input voltage. X-EMI™ inductor technology enables inductors to be drawn directly on the PC board. This technology meets or exceeds the EMI performance of chip inductors and eliminates the need for discrete inductors. The SC220/Q uses a unique constant frequency, selfoscillating control loop architecture to provide excellent transient performance. Under light loads, the device operates in Power Save mode(PSAVE) maintaining a typical quiescent current of 19µA. At moderate to heavy loads, this part operates in PWM mode with a constant switching frequency of 20MHz. This high switching frequency offers the advantages of using small and low cost external components like a 1µF external capacitor and a small 220nH inductor (including X-EMI TM PCB trace inductors). The device provides adjustable output voltages down to 1.0V and an output current up to 650mA. An EN pin can be used to synchronize to an external source and includes de-glitching to reduce noise sensitivity. Applications HDTV, Set Top Boxes, Gaming Consoles POL Applications White Goods Automotive AEC-Q100 Qualified Applications The SC220/Q is available in SOIC 8 lead package. The SC220Q is an AEC-Q100 qualified version. Note 1: Purchase of SC220/Q includes royalty-free right to use X-EMITM inductor technology with no additional cost. Typical Application Circuit L , 2 2 0n H V IN P V IN 2.7 ~ 5.5 V SW A V IN VOUT C IN 1 µF SC220 SC220Q EN E n a b le V O U T = 1.8 V u p to 6 5 0m A PGND R1 C OUT 1 µF FB R2 AGND Revision 2.1 © 2014 Semtech Corporation SC220 x SC220Q Pin Configuration Ordering Information Device Package SC220STRT (1)(2) SOIC 8 Lead SW 1 8 PGND SC220QSTRT (1)(2)(3) SOIC 8 Lead P V IN 2 7 AGND SC220EVB Evaluation Board VOUT 3 6 A V IN SC220QEVB Evaluation Board FB 4 5 EN SOIC 8 Lead, θJA = 38 °C/W Notes: (1) Available in tape and reel only. A reel contains 2,500 devices. (2) Device is lead-free, halogen-free, and RoHS/WEEE compliant. (3) Device is AEC-Q100 qualified. Marking Information SC220 yyww xxxxx n n n n n= P a rt N u m b e r yyw w = D a te co d e xxxxx = S e m te ch L o t N u m b e r SC220Q yyww xxxxx n n n n n n= P a rt N u m b e r yyw w = D a te co d e xxxxx = S e m te ch L o t N u m b e r SC220 x SC220Q Absolute Maximum Ratings Recommended Operating Conditions AVIN, PVIN (V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0 Input Voltage Range (V). . . . . . . . . . . . . . . . . . . . . +2.7 to +5.5 VOUT, FB, EN, SW (V). . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN +0.3) Output DC Current (mA). . . . . . . . . . . . . . . . . . . . . up to 650 AGND (V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 Operating Temperature Range (°C) . . . . . . . . . . -40 to +85 to +0.3 ESD Protection Level (kV). . . . . . . . . . . . . . . . . . . . . . . . . . 3kV (1) Thermal Information Thermal Resistance, Junction to Ambient(2) (°C/W)....38 Junction Temperature Range (°C). . . . . . . . . . -40 to +150 Storage Temperature Range (°C). . . . . . . . . . . . . -65 to +150 Lead Temperature (soldering 10s (°C). . . . . . . . . . . . . . . . 260 Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not recommended. Notes: (1) All voltage values in this section are with respect to PGND pin voltage. (2) Tested according to JEDEC standard JESD22-A114-B. (3) Calculated from package in still air, mounted to 3 x 4.5 (in), 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards. Electrical Characteristics Unless otherwise specified: AVIN=PVIN = 3.6V, EN = AVIN = PVIN, CIN=COUT =1.0μF, L=220nH. TA = 25°C for typical values, -40°C < TA = TJ < 85°C for minimum and maximum values. Parameter Symbol Condition Min Typ Max Units 5.5 V 40 µA 1.0 µA POWER SUPPLY Input Voltage VIN 2.7 Input Quiescent Current IVIN_Q No load, no switching Shutdown Current IVIN_SD EN = 0V 19 POWER SWITCH PMOS On Resistance 400 mΩ NMOS On Resistance 360 mΩ OSCILLATOR Switching Frequency fOSC PWM Mode 16 20 24 MHz REGULATION Output Voltage Tolerance(1) Current Limit VOUT_TOL -4.0 4.0 % ILIMIT 850 1300 mA Soft-Start(1) tSS EN pin low to high Feedback Voltage VFB 2.7V ≤ VIN ≤ 5.5V 40 0.97 1.00 µs 1.03 V SC220 x SC220Q Electrical Characteristics (continued) Unless otherwise specified: AVIN=PVIN = 3.6V, EN = AVIN = PVIN, CIN=COUT =1.0μF, L=220nH. TA = 25°C for typical values, -40°C < TA = TJ < 85°C for minimum and maximum values. Parameter Feedback Leakage Current Symbol Condition Min Typ IFB Max Units 1 µA ENABLE EN Input High Voltage Threshold VENH EN Input “Low” Voltage Threshold VENL EN Input High Current IENH VEN= VIN EN Input Low Current IENL VEN= AGND fSYN_MIN Square wave applied at EN pin Minimum Synchronization Frequency 1.2 V 0.4 V -1.0 1.0 µA -1.0 1.0 µA 3 MHz PROTECTION Over Temp Thermal Shutdown(1) TOT 150 °C Thermal Shutdown Hysteresis(1) THYST 15 °C Notes (1) Guaranteed by design. Not tested in production. SC220 x SC220Q Pin Descriptions Pin # Pin Name Pin Function 1 SW Switching output node — connect to the output LC filter. 2 PVIN Power input supply voltage (2.7 to 5.5V). 3 VOUT Input for sensing the output of LC filter. 4 FB Input for regulation of output LC filter — Using R1 and R2 to set the output voltage, VOUT = VFB x (1+ R1/R2). (Please refer to the typical application circuit diagram on page 1). 5 EN Enable Input — when low, circuit draws <1µA. Apply a square wave clock at EN to synchronize the switching frequency with an external clock. It is recommended that the externally applied clock frequency should not be above 20MHz. 6 AVIN Input supply voltage 7 AGND Analog ground 8 PGND Power ground Block Diagram EN 1.0V REF 5 FB 4 6 2 Soft-Start 20MHz CLIM Frequency Control External Freq. Synchronization + Error Amp - PVIN OSC Thermal Shutdown 1.0V AVIN + Comp - Control Logic Driver 1 SW ZCD Compensator 7 3 VOUT 8 AGND PGND SC220 x SC220Q Typical Characteristics Efficiency vs. Load Current VOUT = 1.8V 100 % 70 % Efficiency 80 % 70 % VIN = 4.2V 50 % 40 % 40 % 30 % 20 % 10 % 10 % 0.01 0.1 Load Current (A) IOUT = 1mA 50 % 30 % 0.001 IOUT = 50mA 60 % 20 % 0 IOUT = 300mA 90 % 80 % 60 % VOUT = 1.8V 100 % VIN = 2.7V VIN = 3.7V 90 % Efficiency Efficiency vs. VIN 0 2.5 1 3.0 Efficiency vs. Load Current 5.0 Nominal VOUT = 1.8V VOUT = 1.8V 100 % VIN = 2.7V Output Voltage (V) 70 % 60 % VIN = 4.2V 50 % 1.80 VIN = 3.7V 80 % Efficiency 4.5 Load Regulation (Chip Inductor vs. X-EMITM Inductor) 90 % 3.5 4.0 Input Voltage (V) 40 % VIN = 5.0V 1.79 VIN = 4.2V 1.78 30 % VIN = 2.7V VIN = 3.7V 20 % Dashed Lines: Efficiency with X-EMITM Inductor Solid Lines: Efficiency with chip Inductor 10 % 0 0.01 0.1 Load Current (A) 0.001 1.77 1 1 VOUT = 1.0V VOUT = 1.8V 22.5 22.5 IOUT = 200mA 20.0 20.0 17.5 Switching Frequency (MHz) Switching Frequency (MHz) 0.1 Switching Frequency vs. VIN Switching Frequency vs. VIN 15.0 12.5 IOUT = 300mA 10.0 7.5 IOUT = 450mA 5.0 2.5 0 0.01 Load Current (A) 0.001 3.0 3.5 4.0 4.5 Input Voltage (V) IOUT = 300mA 15.0 IOUT = 650mA 12.5 IOUT = 450mA 10.0 7.5 5.0 2.5 IOUT = 650mA 2.5 IOUT = 200mA 17.5 5.0 5.5 0 2.5 3.0 3.5 4.0 4.5 Input Voltage (V) 5.0 5.5 SC220 x SC220Q Typical Characteristics (Continuous) Load Transient Response Load Transient Response VIN = 3.7V, VOUT = 2.0V, IOUT = 0mA - 650mA VOUT (ac coupled) VIN = 3.7V, VOUT = 2.0V, IOUT = 200mA - 500mA VOUT (ac coupled) 100mV/div. 50mV/div. IOUT IOUT 200mA/div. 200mA/div. Time (1µs/div) Time (1µs/div) Steady State Operation (IOUT = 300mA) Steady State Operation (IOUT = 50mA) VIN = 3.6V, VOUT = 1.8V, IOUT = 50mA VIN = 3.6V, VOUT = 1.8V, IOUT = 300mA IOUT IOUT 50mA/div. 200mA/div. IL 200mA/div. IL 200mA/div. VSW VSW 2V/div. 2V/div. Time (200ns/div) Time (50ns/div) Output Hard Short Input Quiescent Current vs. Temperature VIN = 5.5V, EN = High, FB = High VIN = 5.0V, VOUT = 1.8V, IOUT = 650mA 20.0 Quiescent Current (µA) VOUT 1V/div. IL 500mA/div. 19.5 19.0 18.5 IOUT 500mA/div. Time (500ns/div) 18 -40 -20 0 20 40 60 Temperature (°C) 80 100 SC220 x SC220Q Typical Characteristics (Continuous) Disable Operation Start-up Operation VIN = 3.7V, VOUT = 1.8V, IOUT = 10mA VIN = 3.7V, VOUT = 1.8V, IOUT = 10mA EN EN 5V/div. 5V/div. VIN VIN 2V/div. 2V/div. VOUT VOUT 1V/div. 1V/div. IOUT IOUT 10mA/div. 10mA/div. Time (20µs/div) Time (100µs/div) Start-up Operation Disable Operation VIN = 3.7V, VOUT = 1.8V, IOUT = 650mA VIN = 3.7V, VOUT = 1.8V, IOUT = 650mA EN EN 5V/div. 5V/div. VIN VIN 2V/div. 2V/div. VOUT VOUT 1V/div. 1V/div. IOUT IOUT 500mA/div. 500mA/div. Time (20µs/div) Time (20µs/div) SC220 x SC220Q Applications Information General Description The SC220/Q is a step-down regulator capable of delivering a lower voltage from an input supply voltage of 2.7V to 5.5V with high efficiency. Using a unique control architecture, the SC220/Q is capable of delivering a peak efficiency of 90%, while maintaining efficiency over 80% during light load condition. The converter operates at 20MHz switching frequency with pulse width modulation (PWM) at moderate to heavy loads up to 650mA. Under light load, the converter operates in power save (PSAVE) mode. Control Scheme The SC220/Q operates with a self-oscillating control method based on the output voltage ripple. This control loop compares the output voltage to an internal 1V reference to regulate the output voltage directly, adjusting the turn-on and turn-off time of the power switches such that the output voltage at the load is held at a precise value. This architecture gives a single-cycle response to transient events. To maintain constant frequency, a phase locked loop (PLL) is included to synchronize the switching with an internal clock. This PLL adjusts the effective upper and lower thresholds of the comparator, thus maintaining a constant frequency. Under transient conditions the voltage control loop determines the required switching pattern to best maintain the output voltage. After a short transient, the PLL will bring the switching frequency back to normal. At extreme duty cycles, where the frequency control loop may not be able to maintain frequency lock even under steady-state conditions, frequency may fall, but the output voltage regulation will be maintained by the main voltage control loop. This unique architecture helps to achieve the excellent line and load transient response. Operating Modes The SC220/Q operates in two modes over a wide range of load currents. At moderate to high load, it operates in PWM mode with its switching frequency held constant. Under light loads, the converter enters PSAVE mode automatically. With the typical 220nH inductor, the transition between PWM and PSAVE mode typically occurs in the range of 100-200mA, depending on the input and output voltages. At very light loads, the SC220/Q maintains high efficiency by shutting down all but the most essential circuit blocks, maintaining a typical quiescent current of about 19µA. In this mode, some circuitry used to control absolute DC accuracy is turned off. In that case, there may be a small DC shift (tens of mV) between normal operation and this ‘no-load’ state. However, in the case of a load transient, the system will turn on the high-side FET within nanoseconds as a discontinuous pulse is issued. The transition to PWM mode can occur within that nominal on-time, giving superior no load to full load transient response. The transition from PWM mode to PSAVE mode is controlled by sensing the minimum value of the ripple current. When it drops below a threshold level for 32 consecutive cycles, the transition to PSAVE mode is initiated. Once in PSAVE, the regulation is maintained by modulating the time between fixed current pulses. When a new pulse is required by the loop before the existing pulse has terminated, the loop determines that the load cannot be maintained in PSAVE mode. This prompts an instantaneous switch from PSAVE mode back to PWM mode. Enable and Start-up The SC220/Q is enabled by applying a voltage higher than 1.2V on EN pin pin, and it is disabled when the applied voltage is pulled below the logic low threshold. The EN pin can also be used to set the switching frequency: if a digital clock is fed to EN, the SC220/Q will sense this as a valid enable signal and the external clock will be used rather than the internal 20MHz oscillator. The SC220/Q has an internal soft start circuit that limits the inrush current during start-up with a stepped current limit. Over the course of about 40μs, the SC220/Q is stepped in increments of one quarter of the nominal current limit to full current limit, thereby reducing the worst-case surge current that might otherwise be reflected to the input current. Current Limit The SC220/Q integrates a current limit feature to protect itself and the external components during over load condition. When the current in the high-side PMOS switch exceeds the current limit, the PMOS switch is turned off. SC220 x SC220Q Applications Information (Cont.) The high-side switch is then held off for a period sufficient to allow inductor current to decay. When the output voltage is close to the nominal regulation point, this will look similar to constant current limiting. As the output voltage falls, imposed off-time is such that the frequency will drop so that the inductor will have appropriate time to reset. This may cause the average current to reduce, giving a mild ‘fold-back’ characteristic to the current limit, where the average load current drops as the output voltage collapses (although the peak current maintains its nominal value). In a short-circuit condition, the system runs continuously at this reduced frequency. Load Transient Response The SC220/Q features excellent regulation during line and load transients. This is due to the nature of the proprietary control method and the high di/dt allowed by the use of a small inductor. This allows for best performance while providing the benefit of using a small low cost output capacitor. VOUT shows only tens of milivolts of ripple voltage during a load current step change of 1mA to 650mA within hundreds of nanoseconds, using a 1μF output capacitor. (See the typical performance curves on page 7). X-EMI™ Inductor Technology The SC220/Q is the industry’s first buck regulator that enables designers to draw their own inductors directly on the PC board. This patented technology is called as XEMI™ inductor technology and is different from conventional PCB trace inductors. Conventional PCB trace inductors can be used with high-frequency switchers, but they exhibit significant EMI issues. X-EMI™ inductor technology solves these EMI problems and can meet or exceed the EMI performance of conventional chip inductors. X-EMITM technology works by placing two small air-core inductors adjacent to one another in anti-phase position, where the magnetic fields of each inductor partially cancel one another to reduce EMI. The net flux from the two inductors, partially cancels the wide leakage paths caused by the wide geometry, while still storing the energy of the inductors in series. This approach uses multiple air core inductors implemented using printed circuit traces. Because these traces may be located on internal layers of the PCB, inductors can be designed with almost no impact on the available PCB area for components on the surface of the board. (See the efficiency curves using X-EMI™ inductor technology on page 6). External Components The input and output capacitors used for the operation of the SC220/Q should be multilayer ceramic capacitors, preferably with X7R or X5R dielectric. SC220/Q is optimized to operate with the input and output capacitance of 1μF typical. In practice, the self-resonant frequency of surface mount capacitors of this type is well below 20MHz ripple frequency, so efforts to minimize output ripple may best be focused on minimizing the inductance of the output capacitor and the length of the circuit path to ground rather than on increasing the capacitance value of the output capacitor. The inductor should be a high current inductor rated for currents at least up to 1A. Typical power inductors may be too lossy at 20MHz unless specifically designed for high frequency operation. For inductor value of 220nH, it may be preferred to use wire-wound RF chokes, many of which are rated for appropriate currents. Some Recommended External Components Value Manufacturer Part Number Package 0.22μH Coilcraft XFL2005-221ME 2x2mm 0.24μH Coilcraft 0603LS-241XJL 0603 CIN 1μF Murata GRM155R61C105KA12 0402 COUT 1μF Murata GRM155R61C105KA12 0402 L Figure 1. Top view of an evaluation board with X-EMI inductor 10 SC220 x SC220Q Applications Information (Cont.) PCB Layout Considerations Fundamental layout rules must be followed since the layout is critical for achieving the desirable performance. Poor layout can degrade the performance of the DC-DC converter and can contribute to EMI problems, ground bounce, and resistive voltage losses, and possibly poor regulation and instability. The following guidelines are recommended when developing a PCB layout: . The input capacitor, CIN should be placed as close to the PVIN and PGND pins as possible. This capacitor provides a low impedance loop for the pulsed currents present at the buck converter’s input. Use short wide traces to connect this capacitor as close to the IC as possible. This will minimize EMI and input voltage ripple by localizing the high frequency current pulses. 2. Keep the SW pin traces as short as possible to minimize pickup of high frequency switching edges to other parts of the circuit. COUT and L should be connected as close as possible between the SW and GND pins, with a direct return to the GND pin from COUT. 3. Route the output voltage feedback/sense path away from the inductor and SW node to minimize noise and magnetic interference to the output feedback/ sense path. 4. Use a ground plane referenced to the PGND pin, and the ground connection of the input and output capacitors should be put on this plane and close to each other if possible, and as close to the PGND pin as possible. Use several vias to connect to the component side ground to further reduce noise and interference on sensitive circuit nodes. 5. If possible, minimize the resistance from the VOUT and AGND pin to the load. This will reduce the voltage drop on the ground plane and improve the load regulation. And it will also improve the overall efficiency by reducing the copper losses on the output and ground planes. 11 SC220 x SC220Q Outline Drawing — SOIC 8 Lead A D e N D IM E N S IO N S IN C H E S M IL LIM E T E R S D IM M IN N O M M A X M IN N O M M A X 2X E /2 E1 1 E 2 ccc C 2 X N /2 T IP S e/2 B D aaa C S E A T IN G P LA N E C .0 69 .0 10 .0 65 .0 20 .0 10 .1 93 .1 97 .1 54 .1 57 .2 3 6 B S C .0 5 0 B S C .0 10 .0 20 .0 16 .0 28 .0 41 (.0 41) 8 0° 8° .0 04 .0 10 .0 08 .0 53 .0 04 .0 49 .0 12 .0 07 .1 89 .1 50 A A1 A2 b c D E1 E e h L L1 N 01 a aa b bb ccc h A2 A b xN bbb 1 .75 0 .25 1 .65 0 .51 0 .25 4 .90 5 .00 3 .90 4 .00 6 .0 0 B S C 1 .2 7 B S C 0 .25 0 .50 0 .40 0 .72 1 .04 (1 .04) 8 0° 8° 0 .10 0 .25 0 .20 1 .35 0 .10 1 .25 0 .31 0 .17 4 .80 3 .80 A1 h H C A -B D c GAGE P LA N E 0.25 S E E D E T A IL S ID E V IE W A L (L 1) D E T A IL 01 A NOTES: 1. C O N T R O L L IN G D IM E N S IO N S A R E IN M ILLIM E T E R S (A N G LE S IN D E G R E E S ). 2. D A T U M S -A - A N D -B - T O B E D E T E R M IN E D A T D A T U M P LA N E -H - 3. D IM E N S IO N S "E 1" A N D "D " D O N O T IN C L U D E M O LD F LA S H , P R O T R U S IO N S OR GATE BURRS. 4. R E F E R E N C E JE D E C S T D M S -012, V A R IA T IO N A A . 12 SC220 x SC220Q Land Pattern —SOIC 8 Lead X D IM (C ) G Z Y C G P X Y Z D IM E N S IO N S IN C H E S M ILLIM E T E R S (.2 05) .118 .050 .024 .087 .291 (5.20) 3.00 1.27 0.60 2.20 7.40 P NOTES: 1. T H IS LA N D P A T T E R N IS F O R R E F E R E N C E P U R P O S E S O N L Y . C O N S U LT Y O U R M A N U F A C T U R IN G G R O U P T O E N S U R E Y O U R C O M P A N Y 'S M A N U F A C T U R IN G G U ID E L IN E S A R E M E T . 2. R E F E R E N C E IP C -S M -78 2A , R L P N O . 3 0 0 A . 13 SC220 x SC220Q © Semtech 2013 All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Semtech assumes no responsibility or liability whatsoever for any failure or unexpected operation resulting from misuse, neglect improper installation, repair or improper handling or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the specified range. SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFESUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER’S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney fees which could arise. Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. Contact Information Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111 Fax: (805) 498-3804 www.semtech.com 14