Optoway SPM-9100FG 1 *********************************************************************************************************************************************************************** SPM-9100FG (RoHS Compliant) 3.3V / 850 nm / 2.125 Gbps SFP LC SINGLE-MODE TRANSCEIVER ********************************************************************************************************************************************************************** FEATURES DESCRIPTION l Hot-Pluggable SFP Footprint LC Optical Transceiver l Small Form-Factor Pluggable (SFP) MSA compatible l Compliant with Fiber Channel FC-PH-2 for 200-M5-SN-1 and 200-M6-SN-1 l Compliant with IEEE 802.3z Gigabit Ethernet 1000BASE-SX l Link Distance at 2.125 Gbd 150 m links with 62.5/125 µm MMF Cables 300 m links with 50/125 µm MMF Cables l Link Distance at 1.026 Gbd 300 m links with 62.5/125 µm MMF Cables 500 m links with 50/125 µm MMF Cables l AC/AC Coupling according to MSA l Single +3.3 V Power Supply l RoHS Compliant l -10 to 85oC Operation l Class 1 Laser International Safety Standard IEC 60825 Compliant The SPM-9100FG series multi-mode transceivers is small form factor pluggable module for bi-directional serial optical data communications such as Gigabit Ethernet 1000BASE-SX and Fiber Channel FC-PH-2 for 200-M5-SN-1 and 200-M6-SN-1. It is with the SFP 20-pin connector to allow hot plug capability. This module is designed for multi-mode fiber and operates at a nominal wavelength of 850 nm. The transmitter section uses a Vertical Cavity Surface Emitted Laser (VCSEL) and is a Class 1 laser compliant according to International Safety Standard IEC 60825. The receiver section uses an integrated GaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. APPLICATIONS l l l l Gigabit Ethernet Switches and Routers Fiber Channel Switch Infrastructure XDSL Applications Metro Edge Switching LASER SAFETY This multi-mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ORDER INFORMATION P/No. SPM-9100FG Bit Rate (Gb/s) FC-PI Distance Wavelength (m) (nm) Package Temp. (oC) 2.125/1.063 200/100 150/300** LC SFP -10 to 85 850 TX Power RX Sens. RoHS (dBm) (dBm) Compliant -4 to -9.5 -15 Yes *: 150 meter for 62.5/125 µm MM fiber; 300 meter for 50/125 µm MM Fiber. Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature Power Supply Voltage Symbol Tstg Topr Vcc Min -40 -10 -0.5 Max 85 85 3.6 Units o C o C V Min 3.1 -10 Typ 3.3 Max 3.5 85 250 1000 2125 Notes Air flow 1m/sec Recommended Operating Conditions Parameter Power Supply Voltage Case Operating Temperature Power Supply Current Data Rate Symbol Vcc Topr ICC (TX+RX) Units / Notes V o C / Air flow 1m/sec mA Mb/s *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway SPM-9100FG 2 *********************************************************************************************************************************************************************** Transmitter Specifications (-10 oC < Topr < 85 oC, 3.1V < Vcc < 3.5V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Optical Modulation Amplitude Extinction Ratio Optical Rise Time Optical Fall Time Relative Intensity Noise Electrical Data Input Current – Low Data Input Current – High Differential Input Voltage TX Disable Input Voltage – Low TX Disable Input Voltage – High TX Disable Assert Time TX Disable Deassert Time TX Fault Output Voltage -- Low TX Fault Output Voltage -- High Symbol Min Typ Max Units Notes Po λ ∆λ OMA ER tr tf RIN -9.5 830 --196 --- -4 860 0.85 1 --160 160 -120 dBm nm nm µW dB ps ps dB/Hz IIL IIH VIH - V IL TDIS, L TDIS, H T ASSERT TDEASSERT TFaultL TFaultH -350 350 2.4 0.5 Vcc 10 1 0.5 Vcc+0.3 µA µA V V V µs ms V V --9 0.5 0 2.0 0 2.0 RMS (σ) 2 20 % to 80% Values 20 % to 80% Values Peak-to-Peak 3 3 4 4 1. Output power is power coupled into a 62.5/125 µm MM fiber. 2. An OMA of 196 µW is approximately equal to an average power of -9 dBm assuming an Extinction Ratio of 9 dB. 3. There is an internal 4.7K to 10K ohm pull-up resistor to VccTX. 4. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage). Receiver Specifications (-10oC < Topr < 85oC, 3.1V < Vcc < 3.5V) Parameter Optical Optical Modulation Amplitude Stress RX Sens Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Electrical Differential Output Voltage Output LOS Voltage -- Low Output LOS Voltage -- High Symbol Min Sens 40 96 -3 ---30 1.0 700 Pin Pa Pd VOH – VOL VOL VOH 0.6 0 2.0 Typ Max Units Notes 5 FC-PI Std. 900 µW µW dBm dBm dBm dB nm 2.0 0.8 Vcc+0.3 V V V 0 ------- -16 --- Transition: low to high Transition: high to low 6 6 5. An OMA of 40 µW is approximately equal to an average power of -17 dBm assuming an extinction ratio of 9 dB. 6. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage). *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway SPM-9100FG 3 *********************************************************************************************************************************************************************** CONNECTION DIAGRAM PIN Signal Name 1 2 3 TX GND TX Fault TX Disable 4 MOD-DFE2 5 MOD-DEF1 6 MOD-DEF0 7 8 9 10 N/C LOS RX GND RX GND Description PIN Transmitter Ground Transmitter Fault Indication Transmitter Disable (Module disables on high or open) Modulation Definition 2 – Two wires serial ID Interface Modulation Definition 1 – Two wires serial ID Interface Modulation Definition 0 – Ground in Module Not Connected Loss of Signal Receiver Ground Receiver Ground 11 12 13 RX GND Receiver Ground RX DATA OUT- Inverse Receiver Data Out RX DATA OUT+ Receiver Data Out Signal Name Description 14 RX GND Receiver Ground 15 Vcc RX Receiver Power – 3.3V±5% 16 Vcc TX Transmitter Power – 3.3V±5% 17 18 19 20 TX GND TX DATA IN+ TX DATA INTX GND Transmitter Ground Transmitter Data In Inverse Transmitter Data In Transmitter Ground Module Definition Module Definition MOD-DEF2 PIN 4 MOD-DEF1 PIN 5 MOD-DEF0 PIN 6 Interpretation by Host 4 SDA SCL LV-TTL Low Serial module definition protocol Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway SPM-9100FG 4 *********************************************************************************************************************************************************************** RECOMMENDED CIRCUIT SCHEMATIC VeeT Tx_DISABLE Tx_FAULT (1,17,20) 3 Tx_DISABLE 2 Tx_FAULT 4.7K to 10KΩ LD Driver TD + 18 TD - 19 TD + Z=50Ω 100Ω TD Z=50Ω VccT 1μH 16 Vcc 3.3V 10μF 10nF 10μF 10nF SerDes IC 1μH VccR 15 10μF 10nF RD - 12 Protocol IC RD Z=50Ω 100Ω POST Amp RD + 13 RD + Z=50Ω 4.7K to 10KΩ LOS VeeR MOD_DEF(0) EEPROM MOD_DEF(1) MOD_DEF(2) SFP module depending on SERDES 8 LOSS OF SINGAL (9,10,11,14) 6 MODULE DETECT 5 SCL 4 SDA 4.7K to 10KΩ 4.7K to 10KΩ Vcc 3.3V 4.7K to 10KΩ PACKAGE DIAGRAM Units in mm Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0