UNISONIC TECHNOLOGIES CO., LTD U74HC4066 CMOS IC QUAD BILATERAL SWITCHES DESCRIPTION The UTC U74HC4066 consists of four independent analog switches. Each switch has an Enable input (nE) which is active HIGH to decide the switch status. TSSOP-14 FEATURES * Operation voltage range: 2~10V * Very low “ON” resistance: VCC=4.5V, 50Ω VCC =6V, 45Ω VCC =9V, 35Ω ORDERING INFORMATION Ordering Number U74HC4066G-P14-R U74HC4066G-S14-R SOP-14 Package TSSOP-14 SOP-14 Packing Tape Reel Tape Reel MARKING www.unisonic.com.tw Copyright © 2014 Unisonic Technologies Co., Ltd 1 of 7 QW-R502-274.D U74HC4066 PIN CONFIGURATION FUNCTION TABLE CMOS IC INPUTS(nE) SWITCH H ON L OFF Note: H: High voltage level; L: Low voltage level. LOGIC DIAGRAM UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 7 QW-R502-274.D U74HC4066 CMOS IC ABSOLUTE MAXIMUM RATING (TA=25°C,unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT Supply Voltage VCC -0.5 ~ +11 V Input Diode Current IIK ±20 mA Switch Diode Current ISK ±20 mA Switch Current IS ±25 mA VCC or GND Current ICC ±50 mA Power Dissipation 500 mW Derate above 70°C SOP-14 PD 8 mW/K Derate above 60°C TSSOP-14 5.5 mW/K Storage Temperature TSTG -65 ~ +150 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. RECOMMENDED OPERATING CONDITIONS PARAMETER Supply Voltage Input Voltage Switch Voltage Input Transition Rise or Fall Rate Operating Temperature SYMBOL VCC VIN VS tR, tF TA UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw TEST CONDITIONS VCC =2.0V VCC =4.5V VCC =6.0V VCC =10.0V MIN TYP MAX UNIT 2.0 5.0 10.0 V GND VCC V GND VCC V 6 1000 ns 500 ns 400 ns 250 ns -40 85 °C 3 of 7 QW-R502-274.D U74HC4066 CMOS IC ELECTRICAL CHARACTERISTICS (TA=25°C,unless otherwise specified) PARAMETER SYMBOL High-Level Input Voltage VIH Low-Level Input Voltage VIL Input Leakage Current current per channel II(LEAK) OFF-state ON-state Quiescent Supply Current IS IQ Peak ON-resistance RON Rail Maximum variation of ON-resistance between any two channels △RON TEST CONDITIONS MIN VCC=2.0V 1.5 VCC=4.5V 3.15 VCC=6.0V 4.2 VCC=9.0V 6.3 VCC=2.0V VCC=4.5V VCC=6.0V VCC=9.0V VCC=6V,VIN=VCC or GND VCC=10V,VIN=VCC or GND VCC=10V, VIN=VIH or VIL, VS=VCC-GND VCC=6V , VIN=VIS=VOS=VCC or GND VCC=10V , VIN=VIS=VOS=VCC or GND VCC=4.5V, IS=1mA, VIN=VIH or VIL, VIS=VCC to GND VCC=6.0V, IS=1mA, VIN=VIH or VIL, VIS=VCC to GND VCC=9.0V, IS=1mA, VIN=VIH or VIL, VIS=VCC to GND VCC=2.0V, IS=100μA, VIN=VIH or VIL, VIS=GND VCC=4.5V, IS=1mA, VIN=VIH or VIL, VIS=GND VCC=6.0V, IS=1mA, VIN=VIH or VIL, VIS=GND VCC=9.0V, IS=1mA, VIN=VIH or VIL, VIS=GND VCC=2.0V, IS=100μA, VIN=VIH or VIL, VIS=VCC VCC=4.5V, IS=1mA, VIN=VIH or VIL, VIS=VCC VCC=6.0V, IS=1mA, VIN=VIH or VIL, VIS=VCC VCC=9.0V, IS=1mA, VIN=VIH or VIL, VIS=VCC VCC=4.5V, VIN=VIH or VIL, VIS=VCC to GND VCC=6.0V, VIN=VIH or VIL, VIS=VCC to GND VCC=9.0V, VIN=VIH or VIL, VIS=VCC to GND UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw TYP MAX UNIT V V V V 0.50 V 1.35 V 1.80 V 2.70 V ±1.0 μA ±2.0 μA ±1.0 μA ±1.0 μA 20 μA 40 μA 54 118 Ω 42 105 Ω 32 88 Ω 80 Ω 35 95 Ω 27 82 Ω 20 70 Ω 100 Ω 42 106 Ω 35 94 Ω 27 78 Ω 5 Ω 4 Ω 3 Ω 4 of 7 QW-R502-274.D U74HC4066 CMOS IC DYNAMIC CHARACTERISTICS (TA=25℃, GND=0V; tR=tF=6ns; CL=50pF) PARAMETER SYMBOL Propagation Delay From VIS to VOS tPHL/tPLH Turn-ON Time from nE to VOS tPZH/tPZL Turn-OFF Time from nE to VOS tPHZ/tPLZ Sine-Wave Distortion THD Switch OFF Signal Feed-Through (Note 1) αOFF Crosstalk Between any two Switches (Note 1) αCT(S) Crosstalk Voltage Between any input to any Switch (Peak-to-Peak Value) V(P-P) TEST CONDITIONS VCC=2.0V, RL=∞ VCC=4.5V, RL=∞ VCC=6.0V, RL=∞ VCC=9.0V, RL=∞ VCC=2.0V, RL=1KΩ VCC=4.5V, RL=1KΩ VCC=6.0V, RL=1KΩ VCC=9.0V, RL=1KΩ VCC=2.0V, RL=1KΩ VCC=4.5V, RL=1KΩ VCC=6.0V, RL=1KΩ VCC=9.0V, RL=1KΩ VCC=4.5V, VIS(P-P)=4V, f=1kHz, RL=10k VCC=9V, VIS(P-P)=8V, f=1kHz, RL=10k VCC=4.5V, VIS(P-P)=4V, f=10kHz, RL=10k VCC=9V, VIS(P-P)=8V, f=10kHz, RL=10k VCC=4.5V, RL=600Ω, f=1MHz VCC=9V, RL=600Ω, f=1MHz VCC=4.5V, RL=600Ω, f=1MHz VCC=9V, RL=600Ω, f=1MHz VCC=4.5V, RL=600Ω, f=1MHz VCC=9V, RL=600Ω, f=1MHz VCC=4.5V, RL=50Ω, CL=10pF VCC=9V, RL=50Ω, CL=10pF Minimum Frequency Response(-3dB) fMAX (Note 2) maximum switch capacitance CS Note 1. Adjust input voltage VIS is 0dbm level (0dbm=1mW into 600Ω) 2. Adjust input voltage VIS is 0dbm level at VOS for 1MHz (0dbm=1mW into 50Ω) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN TYP MAX UNIT 8 75 ns 3 15 ns 2 13 ns 2 10 ns 36 125 ns 13 25 ns 10 21 ns 8 16 ns 44 190 ns 16 38 ns 13 33 ns 16 26 ns 0.04 % 0.02 % 0.12 % 0.06 % -50 -50 -60 -60 110 220 180 200 8 dB dB dB dB mV mV MHz MHz pF 5 of 7 QW-R502-274.D U74HC4066 CMOS IC TEST CIRCUIT AND WAVEFORMS Test circuit for measuring ON-resistance (Ron) Test circuit for measuring OFF-state current Test circuit for measuring ON-state current UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 7 QW-R502-274.D U74HC4066 CMOS IC TEST CIRCUIT AND WAVEFORMS(Cont.) tPLH/tPHL tPHZ/tPZH tPLZ/tPZL S OPEN GND VCC VIN VCC GND Note: 1. CL includes probe and jig capacitance. Note: 2.PRR ≤1MHz, Zo = 50Ω, tR ≤6ns, tF ≤6ns. UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 7 QW-R502-274.D