SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO AM-480272H3TMQW -T01H APPROVED BY DATE Approved For Specifications ; Approved For Specifications & Sample AMPIRE CO., LTD. 2F., No.88, Sec. 1, Sintai 5th Rd., Sijhih City, Taipei County 221, Taiwan (R.O.C.)台北縣汐止市新台五路一段 88 號 2 樓(東方科學園區 D 棟) TEL:886-2-26967269 , FAX:886-2-26967196 or 26967270 APPROVED BY Date: 2009/05/22 CHECKED BY AMPIRE CO., LTD. ORGANIZED BY 1 RECORD Revision Date Page OF REVISION Contents Editor - New Release Edward Date: 2009/05/22 AMPIRE CO., LTD. 2009/5/22 2 1. FEATURES (1) Construction : a-Si TFT-LCD with driving system, White LED Backlight and Touch Panel. (2) LCD type : Transmissive , Normally White (3) Number of the Colors : 16.7M colors (R,G,B 8 bit digital each) (4) RGB Interface 54 pin. (5) LCD Power Supply Voltage : 3.3V single power input, 2. PHYSICAL SPECIFICATIONS Item Specifications unit 4.3 inch 480RGB (W) x 272(H) dots 98.7 (W) x57.5 (H) mm 0.198 (W) x 0.198 (H) mm Overall dimension 105.5(W) x 67.2(H) x 4.96(D) mm Color configuration R.G.B Vertical stripe Display size (diagonal) Resolution Display area Pixel pitch View Direction (Gray Inversion) 6 o’clock 3. ABSOLUTE MAXIMUM RATINGS item Symbol Values Min Max Unit Remark Power Supply for logic VCC -0.3 5.0 V GND=0 Operation Temperature (Ambient) TOP -20 70 ℃ Storage Temperature (Ambient) TST -30 80 ℃ Note 1 LED Forward current If 20 mA OneLED/Note2 LED Power Dissipation Pd 64 mW One LED *TFT LCD Ratings Note 1: Hsync, Vsync, DEN, DCLK, R0~R7, G0~G7, B0~B7 Note 2: Background color changes slightly depending on ambient temperature. This phenomenon is reversible. Date: 2009/05/22 AMPIRE CO., LTD. 3 3.1 Power Voltage item Symbol Logic power supply VCC Min 2.7 Values Typ 3.0 Max 3.6 Unit Remark 4. OPTICAL CHARACTERISTICS Item Symbol Response Time Tr +Tf Contrast ratio Viewing Angle CR Vertical Θ Horizontal Φ Luminance L Color chromaticity Wx Wy White Condition Θ=Φ=0° Min. Typ. - 40 CR≧10 Θ=Φ=0° Max. 250 - 90. - 130 - 400 - Unit Note ms (3) - (1) Deg. (4) cd/m2 (2) 0.301 0.339 (2)(3) NOTE : Measure Condition:IL= 20.0mA Measure Item Definition as follow： (1)Definition of Contrast Ratio：(Measured by BM-7 (TOPCON) [dark room] ) Contrast Ratio (CR)= (White) Luminance of ON ÷ (Black) Luminance of OFF (2) Definition of Center Luminance &Luminance Uniformity：(Measured by BM-7 (TOPCON) [dark room] ) Center Luminance：Measure luminance on Point No5 as figure 9-1. Luminance Uniformity：Measure maximum luminance(L(MAX) )and minimum luminance (L(MIN) )on the 9 points as figure 9-1. L = [L(MIN)/L(MAX)]×100%△ Date: 2009/05/22 AMPIRE CO., LTD. 4 (3) Response Time (White - Black) (4)Definition of Viewing Angle ()：(by EZ-CONTRAST (ELDIM) in the dark room. ) Date: 2009/05/22 AMPIRE CO., LTD. 5 5. ELECTRICAL CHARACTERISTICS LCD driving Item Symbol Min. Typ. Max. Unit Power supply voltage VDD 3.0 3.3 3.6 V H Level VIH 0.8 VDD -- VDD V L Level VIL 0 -- 0.2 VDD V IDD -- 45 -- mA Input voltage for logic Power Supply current Note (1) (2) Note 1: Hsync, Vsync, DEN, DCLK, R0~R5, G0~G5, B0~B5 Note 2: fV =60Hz , Ta=25℃ , Display pattern : All Black LED back light specification Item Symbol Conditions TYP. MAX. Forward voltage Vf If =18mA Forward current If 7-chip serial - 18 20 Uniformity (with L/G) - If=18mA 75%*1 - - 23.1 Luminous color White Chip connection 7 chip serial connection Unit V mA The constant current source is needed for white LED back-light driving. When LCM is operated over 60 deg.C ambient temperature, the ILED of the LED back-light should be adjusted to 15mA max Allowable Forward Current IF (mA) MIN. Date: 2009/05/22 AMPIRE CO., LTD. 6 6. Touch Screen Panel Specifications 6.1 . Electronic characteristics Item Min. Terminal Resistance Insulation resistance Linearity Rated Voltage Transparency Typ. Max. Unit Note 500 1400 Ω X(Film side) 100 700 Ω Y(Glass side) MΩ DC25V % V % DC Non-glare 20 1.5 7 80 Note: Do not operate it with a thing except a polyacetal pen(tip R0.8mm or less) or a finger especially those with hard or sharp tips such as a ball point pen or a mechanical pencil. 6.2. Mechanical & Reliability Characteristics Item Min. Typ. Max. Unit Note Activation force 250 G (1) Durability-surface Write Characters (2) scratching 100,000 Durability-surface 1,000,000 Touches (3) pitting Surface hardness 3 H JIS K5600 Note: 1.Stylus pen Input:R0.8mm polyacetal pen or Finger 2.Measurement for Surface area -1,000,000 times or over -Writing with R0.8mm plastic stylus pen; writing force 250g in active area. -Speed is 60mm/sec 3.1,000,000,tines or over(No damage on film surface) 6.3. Interface No. Symbol 1 XR Touch Panel Right Signal in X Axis 2 YD Touch Panel Bottom Signal in Y Axis 3 XL Touch Panel Left Signal in X Axis 4 YU Touch Panel Top Signal in Y Axis Date: 2009/05/22 Function AMPIRE CO., LTD. 7 7. BLOCK DIAGRAM Date: 2009/05/22 AMPIRE CO., LTD. 8 8. TFT LCD Panel FPC Descriptions Pin no 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Symbol VBLVBLVBL+ VBL+ GND DISP GND NC NC NC NC B0 B1 B2 B3 B4 B5 B6 B7 G0 G1 G2 G3 G4 G5 G6 G7 R0 R1 R2 R3 R4 R5 R6 R7 Date: 2009/05/22 Function LED backlight Cathode LED backlight Cathode LED backlight Anode LED backlight Anode Ground Display ON/OFF Ground No Connection No Connection No Connection No Connection Blue Data Bit 0 Blue Data Bit 1 Blue Data Bit 2 Blue Data Bit 3 Blue Data Bit 4 Blue Data Bit 5 Blue Data Bit 6 Blue Data Bit 7 Green Data Bit 0 Green Data Bit 1 Green Data Bit 2 Green Data Bit 3 Green Data Bit 4 Green Data Bit 5 Green Data Bit 6 Green Data Bit 7 Red Data Bit 0 Red Data Bit 1 Red Data Bit 2 Red Data Bit 3 Red Data Bit 4 Red Data Bit 5 Red Data Bit 6 Red Data Bit 7 AMPIRE CO., LTD. 9 36 37 38 39 40 41 42 43 HSYNC VSYNC DCLK NC NC VCC VCC GND 44 R/L 45 NC 46 U/D 47 48 49 50 51 52 53 54 NC GND GND GND NC ENB GND GND Date: 2009/05/22 Horizontal Sync Input Vertical Sync Input Dot Data Clock NC NC Power Supply(2.5V~3.6V) Power Supply(2.5V~3.6V) Ground Shift direction control pin for Horizontal R/L=H, STV OUT1 OUT2 • • •OUT480 R/L=L, STV OUT480 OUT479 • • •OUT1 NC Shift direction control pin for Vertical U/D=H, STV OUT1 OUT2 • • •OUT272 U/D=L, STV OUT272 OUT271 • • •OUT1 NC Ground Ground Ground NC Data Enable Ground Ground AMPIRE CO., LTD. 10 9. INPUT SIGNAL 9.1 Parallel RGB input timing Chart Date: 2009/05/22 AMPIRE CO., LTD. 11 9.2 Timing Specification Parallel RGB input timing requirement PARAMETER Symbol Min. Typ. Max. Unit Clock cycle Hsync cycle 1/tC*1 1/fH 9 17.14 15 - MHz KHz Vsync cycle 1/fV 59.94 - Hz 575 480 2 41 2 605 480 82 41 41 CLK CLK CLK CLK CLK 285272 1 1 1 286 272 2 10 2 511 272 227 11 11 Min. Typ. Max. Unit 10 10 66.7 26.7 26.7 10 10 10 10 10 10 10 10 - - ns ns ns ns ns ns ns ns ns ns ns ns ns Horizontal Signal Horizontal cycle Horizontal display period Horizontal front porch Horizontal pulse width Horizontal back porch th*2 thd thf thp thb 575 480 2 2 2 Vertical Signal Vertical cycle tv tvd tvf tvp tvb H Vertical display period H Vertical front porch H Vertical pulse width H Vertical back porch H Note: 1. Unit: CLK=1/ fCLK , H=th 2.Parallel interface. Clock frequency and horizontal signal parameters are tripled in serial interface. The Maximum clock frequency of serial interface is 33MHz 3. thd=480CLK, thf=2CLK, thp=41CLK, thb=2CLK, thf + fhp + ftb > 44 9.3 Timing Chart 2 Input setup timing requirement PARAMETER Symbo l DISP setup time DISP hold time Clock period Clock pulse high period Clock pulse low period Hsync setup time Hsync hold time Data setup time Data hold time DE setup time DE hold time Vsync setup time Vsync hold time Note tdiss tdish PWCLK*1 PWH*1 PWL*1 ths thh tds tdh tdes tdeh tvhs tvhh - 1. For parallel interface, maximum clock frequency is 15MHz. 2. tr, tf is defined 10% to 90% of signal amplitude. Date: 2009/05/22 AMPIRE CO., LTD. 12 9.4 Input setup timing Chart Date: 2009/05/22 AMPIRE CO., LTD. 13 10. Color Data Assignment Date: 2009/05/22 AMPIRE CO., LTD. 14 11. QUALITY AND RELIABILITY 11.1Test Conditions Tests should be conducted under the following conditions : Ambient temperature : 25 ± 5°C Humidity : 60 ± 25% RH. 11.2 Sampling Plan Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan . 11.3 Acceptable Quality Level A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation. 11.4Appearance An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under florescent light. The inspection area of LCD panel shall be within the range of following limits. Date: 2009/05/22 AMPIRE CO., LTD. 15 12. Incoming Inspection Standard No. Item 1 Non display 2 Irregular operation Class Accept of able Defect level Criterion for defects No non display is allowed Major 0.4 No irregular operation is allowed Major 0.4 3 Short No short are allowed Major 0.4 4 Open Any segments or common patterns that don’t activate are rejectable. Major 0.4 Minor 1.5 Minor 1.5 Major 0.4 Minor 1.5 Minor 1.5 5 Black/White spot (I) Size D (mm) D < 0.1 0.1 < D < 0.3 0.3 < D Acceptable number Ignore 4 ※1 0 ※1: The distance of two defects must be more than 20mm. 6 Dot Defect 7 Back Light 8 Display pattern Bright dot N≦2 Dark dot N≦4 Total dot defect N≦6 (Bright dot + Dark dot) Minimum distance between L≧5mm dark dot and dark dot 1. No Lighting is rejectable 2. Flickering and abnormal lighting are rejectable Unit:mm A+B ≤ 0.30 0 < C 2 D+E F+G ≤ 0.25 ≤ 0.25 2 2 Note: 1. Acceptable up to 3 damages 2. NG if there’re to two or more pinholes per dot Blemish & Foreign matters 9 Size: A+ B D= 2 Size D (mm) D < 0.15 0.15 < D < 0.20 0.20 < D < 0.30 0.30 < D Date: 2009/05/22 Acceptable number Ignore 3 2 0 AMPIRE CO., LTD. 16 10 Scratch on Polarizer Width (mm) Length (mm) W≦0.05 and L≦ 0.3 0.05＜W<0.03 0.3＜L < 2.0 Acceptable number Ignore 3 Minor 1.5 Minor 1.5 12 LCD panel Stains that cannot be removed even when wiped lightly Minor with a soft cloth or similar cleaning too are rejectable. 1.5 13 Rust which is visible in the bezel is rejectable. Minor 1.5 Defect of land surface 14 contact (poor soldering) Evident crevices which is visible are rejectable. Minor 1.5 Parts 15 mounting 1. Failure to mount parts 2. Parts not in the specifications are mounted 3. Polarity, for example, is reversed Note: The distance of two defects must be more than 20mm. 11 Bubble in polarizer Stains on surface Rust in Bezel Parts 16 alignment Conductive foreign matter 17 (Solder ball, Solder chips) Faulty PCB 18 correction 19 mura D≦ 0.15 mm, Ignored 0.15 ≦ D ≦ 0.5 mm, N ≦ 4 D ＞ 0.5 mm, not allowable D= (A+B) / 2 Major Major Major 1. LSI, IC lead width is more than 50% beyond pad Minor outline. 2. Chip component is off center and more than 50% of Minor the leads is off the pad outline. 0.4 1.5 1. 0.45<φ ,N≧1 2. 0.30<φ<0.45 ,N≧1 φ:Average diameter of solder ball (unit: mm) 3. 0.50<L ,N≧1 L: Average length of solder chip (unit: mm) 1. Due to PCB copper foil pattern burnout, the pattern is connected, using a jumper wire for repair; 2 or more places are corrected per PCB. 2. Short circuited part is cut, and no resist coating has been performed. Major Minor 0.4 1.5 Minor 1.5 ND 6% , See, not allowable Minor Date: 2009/05/22 AMPIRE CO., LTD. Minor 1.5 Minor 17 [Note1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter [Note2] Bright dot is defined through 6% transmission ND Filter as following. [Note3] C Area: Center of display area C Area: Outer of display area [Note4] Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total quantity. Date: 2009/05/22 AMPIRE CO., LTD. 18 (1) The defects that are not defined above and considered to be problem shall be reviewed and discussed by both parties. (2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted. 13. Reliability Test Test Item High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Thermal Shock Test Humidity Test Test Conditions Note 70±3°C , t=96 hrs -20±3°C , t=96 hrs 80±3°C , t=96 hrs 1,2 1,2 -30±3°C , t=96 hrs -20°C ~ 25°C ~ 70°C 30 m in. 5 min. 30 min. ( 1 cycle ) 1,2 Total 5 cycle 40 °C, Humidity 90%, 96 hrs 1,2 Sweep frequency : 10 ~ 55 ~ 10 Hz/1min Amplitude : 0.75mm Vibration Test (Packing) 2 Test direction : X.Y.Z/3 axis Duration : 30min/each axis Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35°C , 45-65%RH). Definitions of life end point : z Current drain should be smaller than the specific value. z Function of the module should be maintained. z Appearance and display quality should not have degraded noticeably. z Contrast ratio should be greater than 50% of the initial value. Date: 2009/05/22 AMPIRE CO., LTD. 19 14. USE PRECAUTIONS 14.1 Handling precautions 1) The polarizing plate may break easily so be careful when handling it. Do not touch, press or rub it with a hard-material tool like tweezers. 2) Do not touch the polarizing plate surface with bare hands so as not to make it dirty. If the surface or other related part of the polarizing plate is dirty, soak a soft cotton cloth or chamois leather in benzene and wipe off with it. Do not use chemical liquids such as acetone, toluene and isopropyl alcohol. Failure to do so may bring chemical reaction phenomena and deteriorations. 3) Remove any spit or water immediately. If it is left for hours, the suffered part may deform or decolorize. 4) If the LCD element breaks and any LC stuff leaks, do not suck or lick it. Also if LC stuff is stuck on your skin or clothing, wash thoroughly with soap and water immediately. 14.2 Installing precautions 1) The PCB has many ICs that may be damaged easily by static electricity. To prevent breaking by static electricity from the human body and clothing, earth the human body properly using the high resistance and discharge static electricity during the operation. In this case, however, the resistance value should be approx. 1MΩ and the resistance should be placed near the human body rather than the ground surface. When the indoor space is dry, static electricity may occur easily so be careful. We recommend the indoor space should be kept with humidity of 60% or more. When a soldering iron or other similar tool is used for assembly, be sure to earth it. 2) When installing the module and ICs, do not bend or twist them. Failure to do so may crack LC element and cause circuit failure. 3) To protect LC element, especially polarizing plate, use a transparent protective plate (e.g., acrylic plate, glass etc) for the product case. 4) Do not use an adhesive like a both-side adhesive tape to make LCD surface (polarizing plate) and product case stick together. Failure to do so may cause the polarizing plate to peel off. 14.3 Storage precautions 1) Avoid a high temperature and humidity area. Keep the temperature between 0°C and 35°C and also the humidity under 60%. 2) Choose the dark spaces where the product is not exposed to direct sunlight or fluorescent light. 3) Store the products as they are put in the boxes provided from us or in the same conditions as we recommend. Date: 2009/05/22 AMPIRE CO., LTD. 20 14.4 Operating precautions 1) Do not boost the applied drive voltage abnormally. Failure to do so may break ICs. When applying power voltage, check the electrical features beforehand and be careful. Always turn off the power to the LC module controller before removing or inserting the LC module input connector. If the input connector is removed or inserted while the power is turned on, the LC module internal circuit may break. 2) The display response may be late if the operating temperature is under the normal standard, and the display may be out of order if it is above the normal standard. But this is not a failure; this will be restored if it is within the normal standard. 3) The LCD contrast varies depending on the visual angle, ambient temperature, power voltage etc. Obtain the optimum contrast by adjusting the LC dive voltage. 4) When carrying out the test, do not take the module out of the low-temperature space suddenly. Failure to do so will cause the module condensing, leading to malfunctions. 5) Make certain that each signal noise level is within the standard (L level: 0.2Vdd or less and H level: 0.8Vdd or more) even if the module has functioned properly. If it is beyond the standard, the module may often malfunction. In addition, always connect the module when making noise level measurements. 6) The CMOS ICs are incorporated in the module and the pull-up and pull-down function is not adopted for the input so avoid putting the input signal open while the power is ON. 7) The characteristic of the semiconductor element changes when it is exposed to light emissions, therefore ICs on the LCD may malfunction if they receive light emissions. To prevent these malfunctions, design and assemble ICs so that they are shielded from light emissions. 8) Crosstalk occurs because of characteristics of the LCD. In general, crosstalk occurs when the regularized display is maintained. Also, crosstalk is affected by the LC drive voltage. Design the contents of the display, considering crosstalk. 14.5 Other 1) Do not disassemble or take the LC module into pieces. The LC modules once disassembled or taken into pieces are not the guarantee articles. 2) The residual image may exist if the same display pattern is shown for hours. This residual image, however, disappears when another display pattern is shown or the drive is interrupted and left for a while. But this is not a problem on reliability. 3) AMIPRE will provide one year warrantee for all products and three months warrantee for all repairing products. Date: 2009/05/22 AMPIRE CO., LTD. 21 15 OUTLINE DIMENSION Date: 2009/05/22 AMPIRE CO., LTD. 22