Preliminary Specification Final Specification

G057VN01 V1
□ Preliminary Specification
■ Final Specification
Module
5.7 Inch Color TFT-LCD
Model Name
G057VN01 V1
Customer
Date
Approved by
Debbie Chiu
Checked &
Approved by
2009/08/20
Prepared by
David Hsing
Note: This Specification is subject to change
without notice.
Date
2009/08/20
General Display Business Division / AU Optronics
corporation
G057VN01 V1 Ver. 1.0
1/22
G057VN01 V1
Contents
1. Operating Precautions .....................................................................................4
2. General Description..........................................................................................5
2.1 Display Characteristics.......................................................................................................5
2.2 Optical Characteristics .......................................................................................................6
3. Functional Block Diagram................................................................................8
4. Absolute Maximum Ratings .............................................................................9
4.1 Absolute Ratings ................................................................................................................9
4.2 Absolute Ratings of Environment .......................................................................................9
5. Electrical Characteristics ...............................................................................10
5.1 TFT-LCD Driving ..............................................................................................................10
5.2 Backlight Unit Driving ....................................................................................................... 11
6. Signal Characteristic ......................................................................................12
6.1 Pixel Format Image ..........................................................................................................12
6.2 Scanning Direction ...........................................................................................................12
6.3 The Input Data Format .....................................................................................................13
6.4 TFT- LCD Interface Signal Description.............................................................................14
6.5 TFT- LCD Interface Timing ...............................................................................................15
6.6 LED Backlight Unit Interface Signal Description ..............................................................16
6.7 Power ON/OFF Sequence ...............................................................................................16
7. Connector & Pin Assignment.........................................................................17
7.1 TFT- LCD Signal (CN1): LCD Connector .........................................................................17
7.2 LED Backlight Unit (CN2): Backlight Connector...............................................................17
7.3 PIN 1 definition of CN1 and CN2 .....................................................................................18
8. Reliability Test Criteria ...................................................................................18
9. Mechanical Characteristics............................................................................20
10. Label and Packaging ....................................................................................21
10.1 Shipping Label (on the rear side of TFT-LCD display) ...................................................21
10.2 Carton Package .............................................................................................................21
11 Safety..............................................................................................................22
11.1 Keen Edge Requirements ..............................................................................................22
11.2 Materials .........................................................................................................................22
11.3 Capacitors ......................................................................................................................22
11.4 National Test Lab Requirement ......................................................................................22
G057VN01 V1 Ver. 1.0
2/22
G057VN01 V1
Record of Revision
Version and Date Page
Old description
New Description
Remark
0.1, May.22, 2009
All
First edition preliminary specifications
1.0, Aug.20, 2009
11
Max IrushLED = TBD
Max IrushLED = 1.5A
VPWM DIM (Dimming control Voltage High)
Min.: 1.5V
Operating Life
Min.: 25000 Hrs, Typ.: 50000 Hrs
LED Backlight Unit Interface Pin 6 Signal
Description: 0V-Off; 3.3V/NC-On
VPWM DIM (Dimming control Voltage High)
Section 5.2.1
Min.: 2.0V
Operating Life
Section 5.2.1
Min.: 50000 Hrs
LED Backlight Unit Interface Pin 6 Signal
Section 6.6
Description: 0V-Off; 3.3~5V/NC-On
11
11
16
Section 5.2.1
G057VN01 V1 Ver. 1.0
3/22
G057VN01 V1
1. Operating Precautions
1) Display area (Polarizer) of TFT-LCD Module is easily to be damaged, please be cautious and not
to scratch it.
2) Be sure to power off your machine before connecting or disconnecting your signal cable to
TFT-LCD Module.
3) Wipe off water drop on display area immediately. Long contact with water may cause
discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth.
5) Display area (Glass) of TFT-LCD Module may be broken or cracked if bump Module against hard
object.
6) To avoid ESD (Electro Static Discharde) damage, be sure to ground yourself before handling
TFT-LCD Module.
7) Do not open nor modify the TFT-LCD module assembly.
8) Do not press the reflector sheet at the back of the module to any direction.
9) In case if TFT-LCD module has to be put back into the packing container slot after it was taken
out from the container, do not press the center of the LED Reflector edge. Instead, press at the
far ends of the LED Reflector edge softly. Otherwise the TFT-LCD Module may be damaged.
10) When inserting or removing of your signal cable to TFT-LCD Module, be sure not to apply
abnormal force (rotate, tilt…etc.) to the Connector of the TFT-LCD Module.
11) TFT-LCD Module is not allowed to be twisted & bent even force is added on module in a very
short time. Please design your display product well to avoid external force applying to module by
end-user directly.
12) Small amount of materials without flammability grade are used in the TFT-LCD module. The
TFT-LCD module should be supplied by power complied with requirements of Limited Power
Source (IEC60950 or UL1950), or be applied exemption.
13) Severe temperature condition may result in different luminance, response time.
14) Continuous operating TFT-LCD Module under high temperature environment may accelerate
LED light bar exhaustion and reduce luminance dramatically.
15) The data on this specification sheet is applicable when TFT-LCD module is placed in landscape
position.
16) Continuous displaying fixed pattern may induce image sticking. It’s recommended to use screen
saver or moving content periodically if fixed pattern is displayed on the screen.
G057VN01 V1 Ver. 1.0
4/22
G057VN01 V1
2. General Description
G057VN01 V1 is designed for industrial display applications with VGA (640 x RGB x 480) resolution
and 262k colors (RGB 6-bits). It is composed of a TFT-LCD panel, driver ICs, control and power
supply circuits board and backlight unit including LED driver circuit. G057VN01 V1 offers CMOS
interface for display signal input.
2.1 Display Characteristics
The following items are G057VN01 V1 characteristics summary at 25
℃(Room Temperature).
Items
Unit
Specifications
Screen Diagonal
inch
5.7
Active Area
mm
115.2(H) x 86.4(V)
Pixels H x V
Pixel Pitch
640 x 3(RGB) x 480
mm
0.18 x 0.18
Pixel Arrangement
R.G.B. Vertical Stripe
Display Mode
TN, Normally White
Nominal Input Voltage VDD
Volt
3.3 typ.
Typical Power Consumption
Watt
3.34W (LCD:0.46W/LED BLU: 2.88W)
@ All black pattern, Full Load and VLED=12V
Weight
Physical Size
Grams
mm
160g (typ.), 175g (max.)
144.0(H)x 104.6(V) x 12.3(D) (typ.)
Electrical Interface
CMOS 6-bit Parallel RGB
Surface Treatment
Anti-Glare, Hardness 3H
Support Color
262K colors
The most suitable view angle
12 o’clock
Temperature Range
Operating
Storage (Non-Operating)
RoHS Compliance
o
C
C
o
-30 to +85
-30 to +85
RoHS Compliance
G057VN01 V1 Ver. 1.0
5/22
G057VN01 V1
2.2 Optical Characteristics
℃ (Room Temperature).
The optical characteristics are measured under stable conditions at 25
Item
Unit
White Luminance
cd/m2
Uniformity
%
Conditions
VLED =12V, DPWM =100%
(center point)
Viewing Angle
Max.
Remark
525
700
-
Note 1
-
1.3
500
800
-
msec
Rising
-
15
20
msec
Falling
-
10
15
msec
Rising + Falling
-
25
35
degree
degree
Horizontal
CR = 10
(Right)
(Left)
70
80
-
70
80
-
degree
degree
Vertical
CR = 10
(Upper)
(Lower)
60
70
-
60
70
-
White x
0.263
0.313
0.363
White y
0.279
0.329
0.379
Red x
0.510
0.560
0.610
Red y
0.280
0.330
0.380
Green x
0.275
0.325
0.375
Green y
0.535
0.585
0.635
Blue x
0.100
0.150
0.200
Blue y
0.055
0.105
0.155
-
50
-
Color / Chromaticity
Coordinates
(CIE 1931)
Color Gamut
Typ.
5 Points
Contrast Ratio
Response Time
Min.
%
Note
1, 2, 3
Note 4
Note 5
Note 6
Note 1: Measurement method
Equipment
Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent)
Aperture
1
Test Point
Center
Environment
< 1 lux
∘with 50cm viewing distance
LCD Module
SR_3 or
equivalent
measuring distance
Module Driving Equipment
G057VN01 V1 Ver. 1.0
6/22
G057VN01 V1
Note 2: Definition of 5 points position (Display active area: 115.2mm(W) x 86.4mm(H))
W
W /4
W /4
W /4
W /4
H /4
1
2
H /4
3
H
H /4
5
4
H /4
Note 3:
The luminance uniformity of 5 points is defined by dividing the maximum luminance value by the minimum luminance
value at full white condition.
δ
Maximum Brightness of five points
W5
=
Minimum Brightness of five points
Note 4: Definition of contrast ratio (CR):
Brightness @ “White” state
Contrast ratio (CR) =
Brightness @ “Black” state
Note 5: Definition of response time:
The output signals of photo detector are measured when the input signals are changed from “White” to “Black” (falling
time) and from “Black” to “White” (rising time), respectively. The response time interval definition is between 10% and 90%
of amplitude. Please refer to the figure as below.
%
Tf
Tr
100
90
Optical
White
Black
White
response
10
0
G057VN01 V1 Ver. 1.0
7/22
G057VN01 V1
Note 6: Definition of viewing angle
Viewing angle is the measurement of contrast ratio
≧10, at the screen center, over 180° horizontal and 180° vertical
range. The 180° horizontal (θL, θR) and 180° vertical (ΦH, ΦL) range are illustrated as following figure.
3. Functional Block Diagram
The following diagram shows the functional block of the G057VN01 V1 color TFT/LCD module.
G057VN01 V1 Ver. 1.0
8/22
G057VN01 V1
4. Absolute Maximum Ratings
4.1 Absolute Ratings
Item
Symbo
Min
Max
Unit
Remark
Logic/LCD Drive Voltage
VDD
-0.3
+3.6
Volt
Ta= 25 C
LCD Input Signal Voltage
VIN
-0.3
+3.6
Volt
Ta= 25 C
LED BLU Drive Voltage
VLED
0
23
Volt
Ta= 25 C
VPWM
0
8
Volt
Ta= 25 C
Unit
Remark
LED Dimming Input Voltage
o
o
o
o
High
4.2 Absolute Ratings of Environment
Item
Symbol
Min
Max
Operating Temperature
TOP
-30
+85
℃
Note 1, 2
Operation Humidity
HOP
5
95
%RH
Storage Temperature
TST
-30
+85
℃
Note 1, 2
Storage Humidity
HST
5
95
%RH
Note 1: Maximum Wet-Bulb should be 39
Note 1
Note 1
℃ and no condensation.
Note 2: Only operation is guaranteed. Optical performance should be evaluated at 25℃ only.
G057VN01 V1 Ver. 1.0
9/22
G057VN01 V1
5. Electrical Characteristics
5.1 TFT-LCD Driving
5.1.1 Power Specification
Symbol
Parameter
Min
Typ
Max
Units
3.0
3.3
3.6
Volt
VDD
Logic/LCD Drive Voltage
IDD
VDD Current
-
140
155
mA
Irush
LCD Inrush Current
-
-
1.5
A
PDD
VDD Power
-
0.46
0.51
Watt
Allowable Logic/LCD Drive Ripple Voltage
-
-
100
mVp-p
Remark
All Black Pattern
(VDD=3.3V, at 60Hz)
Note 1
All Black Pattern
(VDD=3.3V, at 60Hz)
All Black Pattern
VDDrp
(VDD=3.3V, at 60Hz)
Note 1: Measurement condition:
+3.3V
Q3
AO6402
D6
D5
D2
D1
F1
S
(LCD Module Input)
G
R1
47K
VDD VCC
(High to Low)
Control
Signal
D1
D2
D5
D6
C1
1uF/16V
Q3
AO6402
R2
S
G
1K
2
C3
+12.0V
SW1
1
SW MAG-SPST
R2
VR1
0.01uF/25V
47K
1K
C2
1uF/25V
3.3V
90%
10%
0V
0.5ms
VDD rising time
G057VN01 V1 Ver. 1.0
10/22
G057VN01 V1
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when VDD is off.
Parameter
Symbol
Min.
Typ.
Max.
Unit
Logic Input Voltage for
High
VIH
0.7VDD
-
VDD
Volt
Display Signals
Low
VIL
0
-
0.3VDD
Volt
High
VIH
0.7VDD
-
VDD
Volt
Low
VIL
0
-
0.3VDD
Volt
Remarks
Input Voltage for RL/UD
5.2 Backlight Unit Driving
5.2.1 Parameter guideline for LED
℃ (Room Temperature)
Following characteristics are measured under stable condition using a LED driving board at 25
Symbol
Parameter
Min
Typ
Max
Units
20
Volt
Remark
VLED
Input Voltage
9
12
ILED
Input Current
-
0.24
A
VLED =12V, DPWM =100%
PLED
Power Consumption
-
2.88
W
VLED =12V, DPWM =100%
Inrush Current
-
1.5
A
VLED =12V, DPWM =100%
IrushLED
VPWM DIM
Dimming control Voltage High
2.0
3.3
5.5
Volt
Dimming control Voltage Low
-
-
0.2
Volt
FPWM
Dimming Frequency
200
30K
Hz
DPWM
Dimming duty cycle
1
100
%
On Control Voltage
2
3.3
5.5
Volt
Off Control Voltage
-
-
0.8
Volt
50000
-
-
Hrs
VLED On/Off
Operating Life
Note 1,2
Note 3, 4
Note 5, 6
Note 1: PWM dimming function can be operated by PWM signal. PWM duty cycle can adjust white Luminance.
(PWM High: ON and PWM Low: OFF)
Note 2: PWM signal can not be floating and pull-down to ground when waiting.
Note 3: Enable (VLED On/Off) must be turned on late than VLED and PWM Signal.
Note 4: Enable (VLED On/Off) must be turned off early than VLED and PWM Signal.
Note 5: If G057VN01 V1 module is driven by high current or at high ambient temperature & humidity condition. The
operating life will be reduced.
Note 6: Operating life means brightness goes down to 50% initial brightness. Minimum operating life time is estimated
data.
Note 7: See Section 6.6 for LED Backlight Unit Interface Signal Description
G057VN01 V1 Ver. 1.0
11/22
G057VN01 V1
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship between input signal and LCD pixel format.
6.2 Scanning Direction
The following figures show the image seen from the front view. The arrow indicates the direction of scan.
Note 1: TFT-LCD interface signal description is shown in section 6.4.
G057VN01 V1 Ver. 1.0
12/22
G057VN01 V1
6.3 The Input Data Format
This product displays 262,144 colors in terms of the 64 grey levels on RGB respectively. The following table demonstrates
the display of input data.
G057VN01 V1 Ver. 1.0
13/22
G057VN01 V1
6.4 TFT- LCD Interface Signal Description
Note 1: “Low” stands for 0V. “High” stands for 3.3V. “NC” stands for ”No Connection”.
G057VN01 V1 Ver. 1.0
14/22
G057VN01 V1
6.5 TFT- LCD Interface Timing
6.5.1 Timing Characteristics
DE mode only
Signal
Symbol
Min.
Typ.
Max.
Unit
Remark
1/ TCLOCK
23.9
25.2
34.2
MHz
Note1
Period
TH
770
800
1000
Active
THD
TCLOCK
Note1
Blanking
THB
130
160
360
Period
TV
516
525
570
Active
TVD
TLINE
Note1
Blanking
TVB
Clock frequency (DOTCLK)
Horizontal Section
Vertical Section
640
480
36
45
90
Note 1: Recommended frame rate is 60 Hz.
6.5.2 Input Timing Diagram
Input Timing Definition ( DE Mode)
TCLOCK
DOTCLK
Input
Data
Invaild
Data
Pixel
1
Pixel
2
Pixel
3
Pixel
N-1
Pixel
N
Invaild
Data
Pixel
1
DE
THB
THD
TH
DE
TVB
TVD
TV
G057VN01 V1 Ver. 1.0
15/22
G057VN01 V1
6.6 LED Backlight Unit Interface Signal Description
Pin #
Symbol
Pin Description
1
VLED
12V input
2
VLED
12V input
3
GND
Ground
4
GND
Ground
5
PWM DIM
1~100% PWM dimming
6
LED On/Off
0V-Off; 3.3~5V/NC-On
Note 1: “NC” stands for ”No Connection”
6.7 Power ON/OFF Sequence
VDD power, LCD interface signals and backlight on/off sequence are shown in the following chart. Signals from any
system shall be Hi-Z state or low level when VDD is off.
Power ON/OFF sequence timing
Value
Parameter
Units
Min.
Typ.
Max.
T1
0.5
-
10
ms
T2
0
-
50
ms
T3
0
-
50
ms
T4
0
-
10
ms
T5
200
-
-
ms
T6
200
-
-
ms
T7
500
-
-
ms
ON/OFF sequence should be applied to avoid abnormal function in the display. Please make sure to turn off the power
when you plug the cable into the input connector or pull the cable out of the connector.
G057VN01 V1 Ver. 1.0
16/22
G057VN01 V1
7. Connector & Pin Assignment
7.1 TFT- LCD Signal (CN1): LCD Connector
Manufacturer
Starconn
089H33-000100-G2-R, compatible with
Connector Model Number
IMSA-9637S-33Y902 & ELCO 08-6210--033-340-800+
Pin#
Symbol
Pin#
Symbol
Pin#
Symbol
1
GND
12
GND
23
B3
2
DOTCLK
13
G0
24
B4
3
NC
14
G1
25
B5
4
NC
15
G2
26
GND
5
GND
16
G3
27
DE
6
R0
17
G4
28
VDD
7
R1
18
G5
29
VDD
8
R2
19
GND
30
R/L
9
R3
20
B0
31
U/D
10
R4
21
B1
32
NC
11
R5
22
B2
33
GND
7.2 LED Backlight Unit (CN2): Backlight Connector
Manufacturer
JST
Connector Model Number
SM06B-SRKS-G-TB
compatible with JST SM06B-SRSS-TB (LS) (SN)
Mating Connecter Model Number
JST SHR-06V-BKHF-B or compatible
Pin #
Symbol
Pin #
Symbol
1
VLED
4
GND
2
VLED
5
PWM DIM
3
GND
6
LED ON/OFF
G057VN01 V1 Ver. 1.0
17/22
G057VN01 V1
7.3 PIN 1 definition of CN1 and CN2
8. Reliability Test Criteria
Items
Temperature Humidity Bias
High Temperature Operation
Low Temperature Operation
High Temperature Storage
Low Temperature Storage
Thermal Shock Test
Hot Start Test
Cold Start Test
Required Condition
℃/90%,300Hr
85℃,300Hr
-30℃,300Hr
85℃,300 hours
-30℃,300 hours
-20℃/30 min ,60℃/30 min ,100cycles
85℃/1 Hr (min.), power on/off per 5 minutes, repeat 5 times
-30℃/1 Hr (min.), power on/off per 5 minutes, repeat 5 times
40
Remark
Note 2
Note 2
Note 2
Note 2
Note 2
Note 2
Note 2
Note 2
Shock Test
(Non-Operating)
50G,20ms,Half-sine wave, (±X, ±Y, ±Z)
Note 2
Vibration Test
(Non-Operating)
1.5G, 10~200~10Hz, Sine wave, 30mins/axis, 3 direction (X, Y, Z)
Note 2
Contact Discharge: ±8KV, 150pF(330Ω) 1sec, 8 points, 25 times/point
ESD
Air Discharge: ±15KV, 150pF(330Ω) 1sec, 8 points, 25 times/point
Attitude Test
Operating: 14,000 ft, Ramp: 2000 ft/min, 8hrs
Non-operating: 40,000 ft, Ramp: 2000 ft/min, 24hrs
Note 1,2
Note 2
Note1: According to EN61000-4-2 ESD class B criteria, some performance degradation is allowed. TFT-LCD module
is self-recoverable, no data lost and no hardware failures after test.
G057VN01 V1 Ver. 1.0
18/22
G057VN01 V1
Note2:
Water condensation is not allowed for each test items.
Each test is done by new TFT-LCD module. Don’t use the same TFT-LCD module repeatedly for reliability test.
The reliability test is performed only to examine the TFT-LCD module capability.
To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity for 24
hours at least in advance.
G057VN01 V1 Ver. 1.0
19/22
G057VN01 V1
9. Mechanical Characteristics
G057VN01 V1 Ver. 1.0
20/22
G057VN01 V1
10. Label and Packaging
10.1 Shipping Label (on the rear side of TFT-LCD display)
10.2 Carton Package
Max. capacity: 60 pieces TFT-LCD module per carton
Max. weight: 12.95 kg per carton
Outside dimension of carton: 520(L)mm* 340(W)mm* 250(H)mm
G057VN01 V1 Ver. 1.0
21/22
G057VN01 V1
11 Safety
11.1 Keen Edge Requirements
There will be no keen edges or corners on the display assembly that could cause injury.
11.2 Materials
11.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the TFT-LCD module. If toxic materials are used, they will
be reviewed and approved by the responsible AUO toxicologist.
11.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in the TFT-LCD
Module will complete the flammability rating exception approval process.
The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be
printed on the printed circuit board.
11.3 Capacitors
If any polarized capacitors are used in the TFT-LCD module, provisions will be made to keep them from being
inserted backwards.
11.4 National Test Lab Requirement
The TFT-LCD Module will satisfy all requirements for compliance to UL 60950 (U.S.A. Information Technology
Equipment).
G057VN01 V1 Ver. 1.0
22/22