SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED AM-640480GSTMQW-00H BY DATE Approved For Specifications ;Approved For Specifications & Sample AMPIRE CO., LTD. 2F., No.88, Sec. 1, Sintai 5th Rd., Sijhih City, Taipei County 221, Taiwan (R.O.C.)台北縣汐止市新台五路一段 88 號 2 樓(東方科學園區 D 棟) TEL:886-2-26967269 , FAX:886-2-26967196 or 26967270 APPROVED BY Date : 2009/6/04 CHECKED BY AMPIRE CO., LTD. ORGANIZED BY 1 RECORD Revision Date 2009/4/9 2009/5/13 2009/6/4 OF REVISION Page Contents Editor -- New Release JOHN 3 Add Surface treatment of LCD Edward 16 Revise outline dimension Edward 4 Add LED Life Time Edward 17-18 Add connectors information Edward Date : 2009/6/04 AMPIRE CO., LTD. 2 1. INTRODUCTION This is a color active matrix TFT-LCD that uses amorphous silicon TFT as a switching device . This model is composed of a 5.7inch TFT-LCD panel, a driving circuit and LED backlight system . This TFT-LCD has a high resolution (640(R.G.B) X 480) and can display up to 262,144 colors . 2. PHYSICAL SPECIFICATIONS Item Display resolution(dot) Display area Pixel pitch Specifications unit 640RGB (W) x 480(H) dots 115.2 (W) x 86.4 (H) mm 0.1815 (W) x 0.1815 (H) mm Color configuration R.G.B Vertical stripe Overall dimension 144.0(W)x104.6(H)x12.3(D)---(Typ) mm 400 cd/m2 Brightness Contrast ratio 250 : 1 Backlight unit LED Display color 262,144 Surface treatment colors Anti-Glare 3. ABSOLUTE MAXIMUM RATINGS ITEM SYMBOL MIN MAX Vcc -0.5 5 V DCLK , DE R0~R5 G0~G5 B0~B5 -0.5 Vcc + 0.5 V Operation Temperature Top -20 70 ℃ (1) Storage Temperature Tstg -30 80 ℃ (1) Power Supply Voltage Signal Input Voltage Date : 2009/6/04 AMPIRE CO., LTD. UNIT NOTE 3 4. ELECTRICAL CHARACTERISTICS 4-1 TFT LCD Module voltage ITEM SYMBOL MIN TYP MAX UNIT Power Voltage For LCD VCC 3.0 3.3 3.6 V Power Voltage For VLED VLED -- 12.0 -- V VIH VCC*0.7 -- VCC V VIL 0 -- VCC*0.3 V VIH 3.0 -- 5.0 V VIL GND -- 0.3 V Logic Input Voltage PWM Input Voltage NOTE (1) 4-2 TFT LCD current consumption ITEM SYMBOL MIN TYP MAX UNIT NOTE LCD Power Current Icc - 82 - mA (1) LED Power Current ILED(VLED=12v) - 100 - mA LED Life Time NOTE : 20K (1) Typ : under 64 gray pattern (a) 64 Gray Pattern Date : 2009/6/04 Hours Ta=25℃ ILED=100mA Max : under black pattern (b) Black Pattern AMPIRE CO., LTD. 4 6. INTERFACE Pin no Symbol I/O Description 1 GND I Gound 2 CK I Clock signal. Latching data at the rising edge 3 Hsync I Horizontal sync input in digital RGB mode 4 Vsync I Vertical sync input in digital RGB mode 5 GND I Gound 6 R0 I 7 R1 I 8 R2 I Red data 9 R3 I 10 R4 I 11 R5 I 12 GND I Gound 13 G0 I 14 G1 I 15 G2 I Green data 16 G3 I 17 G4 I 18 G5 I 19 GND I Gound 20 B0 I 21 B1 I 22 B2 I Blue data 23 B3 I 24 B4 I 25 B5 I 26 GND I Gound 27 ENAB I Input data enable control 28 VCC I +3.3V Power Supply 29 VCC I 30 R/L I Right / Left Reveres Mode 31 U/D I Up / Down Reveres Mode 32 NC I No Connection 33 GND I Gound CN2: 1 2 3 4 5 6 12V 12V GND GND PWM LEDO Remark LED drive circuit power supply (12V) LED drive circuit power supply (12V) Gound Gound PWM Dimmer LED OPEN[ normal:High(5V), open error:Low ] Date : 2009/6/04 AMPIRE CO., LTD. 5 NOTE : 1. PWM adjust brightness to control Pin , Pulse duty the bigger the brighter. 2. PWM signal = 0 ~ 5.0V , operation frequency : 200Hz~1KHz 3. U/D and L/R are controlled function L/R : L, U/D : H L/R : L, U/D : L Date : 2009/6/04 L/R : H, U/D : H L/R : H, U/D : L AMPIRE CO., LTD. 6 7. INPUT SIGNAL : 7-1 Timing Specification. PARAMETER CLK frequency CLK period CLK pulse duty HS period HS pulse width HS-first horizontal data time DEN pulse width VS pulse width VS-DEN time VS period Symbol FCPH TCPH TCWH TH TWH THS TEP TWV TSTV TV Min. Typ. Max 25.175 40 5 39.7 50 800 30 60 - 112 144 175 1 - 640 3 35 525 5 - Unit MHz ns % TCPH TCPH TCPH TCPH TH TH TH Note: When SYNC mode is used, 1st data start from 144th CLK after HS falling (when STHD[5:0]=00000) PARAMETER OEV pulse width CKV pulse width HS-CKV time HS-OEV time HS-POL time STV setup time STV pulse width Date : 2009/6/04 Symbol Min. TOEV TCKV T1 T2 T3 TSUV TWSTV Typ. 100 Max - - 96 52 8 72 46 1 - AMPIRE CO., LTD. Unit TCPH TCPH TCPH TCPH TCPH TCPH TH 7 7-2 Timing chart Date : 2009/6/04 AMPIRE CO., LTD. 8 7-3 Color Data Assignment COLOR Input R DATA R5 G DATA R0 G5 B DATA G0 B5 B0 Data MSB R4 R3 R2 R1 LSB MSB G4 G3 G2 G1 LSB MSB B4 B3 B2 B1 LSB BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED(63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 GREEN(63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 BASIC BLUE(63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 COLOR CYAN 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 MAGENTA 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 YELLOW 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 WHITE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 RED(0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED(1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 RED(2) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 RED GREEN BLUE ∣ RED(62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 RED(63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 GREEN (0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GREEN (1) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 GREEN (2) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 GREEN (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 GREEN (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 BLUE (0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 BLUE (1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 BLUE (2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 ∣ ∣ BLUE (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 BLUE (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 NOTE : (1) Definition of Gray Scale , Color(n) : n is series of Gray Scale The more n value is the bright Gray Scale (2) Data : 1-High , 0-Low Date : 2009/6/04 AMPIRE CO., LTD. 9 8. OPTICAL CHARACTERISTICS Item Symbol Condition Min. Typ. Max. Unit Note Contrast ratio CR 200 250 -- -- (1)(2)(3) Luminance Lw -- 400 - cd/m2 (1)(3) Luminance Uniformity ΔL 70 75 - % (1)(3) -- 50 -- ms (1)(3)(5) 80 100 - 120 140 - Deg. (1)(2)(4) 0.566 0.302 0.308 0.518 0.096 0.086 0.296 0.328 0.616 0.352 0.358 0.568 0.146 0.136 0.346 0.378 0.666 0.402 0.408 0.618 0.196 0.186 0.396 0.428 -- (1)(3) Response Time ( White – Black ) Viewing Angle Tr +Tf Vertical Θ Horizontal Φ Red Color chromaticity Point - 5 Θ=Φ=0° Green Blue White CR≧10 Point – 5 Rx Ry Gx Gy Bx By Wx Wy Point - 5 Θ=Φ=0° NOTE : (1) Measure conditions : 25℃±2℃ , 60±10%RH under 10Lux , in the dark room by BM-7TOPCON) ,viewing 2° , VCC=3.3V , VDD=3.3V (2) Definition of Contrast Ratio : Contrast Ratio (CR) = (White) Luminance of ON ÷ (Black) Luminance of OFF (3) Definition of Luminance : Definition of Luminance Uniformity Measure white luminance on the point 5 as figure9-1 Measure white luminance on the point 1 ~ 9 as figure9-1 ΔL = [ L(MIN) / L(MAX)] X 100% Date : 2009/6/04 AMPIRE CO., LTD. 10 (4) Definition of Viewing Angle(Θ,Φ), refer to Fig9-2 as below : (5) Definition of Response Time.(White – Black) Date : 2009/6/04 AMPIRE CO., LTD. 11 9 INCOMING INSPECTION STANDARD FOR TFT-LCD PANEL Note DEFECT TYPE LIMIT φ＜0.15mm 0.15mm≦φ≦0.5mm SPOT FIBER VISUAL DEFECT INTERNAL POLARIZER BUBBLE 0.5mm＜φ 0.03mm<W≦0.1mm, L≦5mm 1.0mm＜W, 1.5mm＜L φ＜0.15mm 0.15mm≦φ≦0.5mm 0.5mm＜φ N≦3 N=0 Ignore N≦2 N=0 Note1 Note1 Note1 It’ OK if mura is slight visible through 6%ND filter Mura A Grade BRIGHT DOT DARK DOT ELECTRICAL DEFECT Ignore N≦4 N=0 B Grade C Area O Area Total C Area O Area Total Note3 N≦0 N≦2 N≦2 N≦2 N≦3 N≦5 Note2 N≦2 N≦3 N≦3 N≦3 N≦5 N≦8 N≦5 N≦6 N≦8 Note2 N≦1 pair N≦1 pair N≦1 pair Note4 TOTAL DOT N≦4 TWO ADJACENT DOT N≦0 N≦1 pair N≦1 pair THREE OR MORE NOT ALLOWED ADJACENT DOT LINE DEFECT NOT ALLOWED (1) One pixel consists of 3 sub-pixels, including R,G, and B dot.(Sub-pixel = Dot) (2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter [Note1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter [Note2] Bright dot is defined through 6% transmission ND Filter as following. Date : 2009/6/04 AMPIRE CO., LTD. 12 [Note3] C Area: Center of display area C Area: Outer of display area [Note4] Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total quantity. (1) The defects that are not defined above and considered to be problem shall be reviewed and discussed by both parties. (2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted. Date : 2009/6/04 AMPIRE CO., LTD. 13 10. RELIABILITY TEST CONDITIONS ITEM CONDITIONS HIGH TEMPERATURE OPERATION 70℃ , 240Hrs HIGH TEMPERATURE AND HIGH HUMIDITY OPERATION 60℃ , 90%RH , 240Hrs HIGH TEMPERATURE STORAGE 80℃ , 240Hrs LOW TEMPERATURE OPERATION -20℃ , 240Hrs LOW TEMPERATURE STORAGE -30℃ , 240Hrs THERMAL SHOCK -30℃(0.5Hr) ~80℃(0.5Hr) 200 Cycle 10.1 OTHERS AMIPRE will provide one year warranty for all products and three months warrantee for all repairing products. Date : 2009/6/04 AMPIRE CO., LTD. 14 11. OUTLINE DIMENSION Date : 2009/6/04 AMPIRE CO., LTD. 15 Date : 2009/6/04 AMPIRE CO., LTD. 16 12. CONNECTORS CN1 Date : 2009/6/04 AMPIRE CO., LTD. 17 CN2 Date : 2009/6/04 AMPIRE CO., LTD. 18