www.osram.com SubstiTUBE® Value – ST8V-0.6m Datasheet Innovative LED-lamp, easy and safe to use in CCG installations as direct retrofit. Energy saving potential of up to 64% by replacing 0.6 m T8 fluorescent tubes. Instant 100% light without flickering. No mercury. Applicable in warehouses, cold storage, supply rooms, corridors, industry, stairways, garages, indirect illumination etc; for applications with high operating hours. Technical operating data Color Colortemp. [K] Lum. Flux [lm] ST8V-0.6m-8.9W-865EM Cool Daylight 6500 K 800 ST8V-0.6m-8.9W-840EM Cool White 4000 K 800 ST8V-0.6m-8.9W-830EM Warm White 3000 K 720 Product Voltage [V] / Frequency [Hz] Input current [A] Power [W] Radiance -Angle [°] 220 - 240 V 50 / 60 Hz 0,04 A 8,9 W 160° All Data are related to the entire lamp. Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Technical Features LED lamp in T8 shape with G13 socket Powerfactor > 0.9 Length excl. pins: 590 mm Up to 30,000 h lifetime Weight: 90g Switching cycles > 200.000 For operation at magnetic ballast Color Rendering Index (CRI) > 80 No rewiring necessary at CCG Overpower, overheat and short circuit protected Direct Retrofit for CCG luminaires; replacement of lamp and included starter Extremely robust due to polycarbonate body Fully integrated ECG complies to relevant standards ST8V-0.6m – April 2015 Page 1 of 5 High color homogeneity RoHS-conformity, no mercury Not for operation with ECG, not dimmable Energy Efficiency Class: A Minimum / Maximum ratings ST8V-0.6m Operating temperature Tc Storage temperature Ts Ambient temperature Ta -20° … 65°C -20° ... 80°C -20° ... 45°C Drawings Product ST8V-0.6m ST8V-0.6m – April 2015 l d 590 mm 27,5 mm Page 2 of 5 Safety and Application notes The SubstiTUBE® Value must not be damaged or operated in a damaged condition. When operating with CCG, the included „SubstiTUBE® Start“ has to be inserted as well. If the conventional starter is not replaced the SubstiTUBE® Value will start blinking. Switch off immediately, the SubstiTUBE® Value can be damaged! Lamp suitable for 50 Hz or 60 Hz operation Lamp not suitable for high frequency operation Lamp not suitable for emergency operation Do not use SubstiTUBE® Value in luminaires which do not have any starter or when the starter cannot be replaced. Not usable in luminaires with serial lamp connection i.e. more than one tube at one magnetic ballast (tandem circuitry). The SubstiTUBE® Value emits light only with a limited angle, not like a fluorescent tube with 360°output. Due to the characteristic light distribution of the SubstiTUBE® Value, the resulting luminaire light characteristic is likely to change. It is not guaranteed that e.g. standards for lighting at working places will be complied to after replacement. A photometric check of the installation is recommended. The effective energy savings depend on the efficiency of the luminaire setup to be replaced and should be considered individually in each case. Particularly magnetic ballast losses are reduced to ohmic losses and are normally only about 1 W. The SubstiTUBE® Value is protected according to IP20. Applications with external risk of moisture and dust can be served with an adequately protected luminaire. SubstiTUBE® Value may also be driven directly on line voltage. In order to grant a safe operation mode please refer to the installation instructions for further information. Maximum amount of SubstiTUBE® Value on one circuit breaker Circuit breaker 10 A (B type) Circuit breaker 16 A (B type) // // // // // // CCG CCG incl. comp. cap. Direct mains CCG CCG incl. comp. cap. Direct mains // // // // // // 170 30 170 270 47 270 Photobiological Safety of lamps and lamp systems according to IEC 62471. Risk Group: Exempt ST8V-0.6m – April 2015 Page 3 of 5 Installation Instructions for CGG Make sure that the supply voltage is disconnected. Carefully remove the fluorescent tube and starter according to the lamp holder type. Insert SubstiTUBE® Value and SubstiTUBE® Start properly. Below an example for typical lamp holder types is described Turn the conventional lamp 90° degrees and take it out of the socket. Remove the conventional starter by turning it. Insert and latch the SubstiTUBE® Start into starter socket. Insert SubstiTUBE® Value into socket and locate into position by turning 90°. Check light emission direction. Circuit diagram of a retrofitted CCG luminaire ST8V-0.6m – April 2015 Page 4 of 5 Ordering guide Product name Light color EAN* S-Unit** ST8V-0.6m-8.9W-865-EM Cool Daylight / 6500 K 4052899937130 ST8V-0.6m-8.9W-840-EM Cool White / 4000 K 4052899937123 ST8V-0.6m-8.9W-830-EM Warm White / 3000 K 4052899937116 8x1 * EAN: Ordering number per single module ** S-Unit: Lamps per shipping unit Sales and Technical Support OSRAM GmbH Sales and technical support is given by the local OSRAM subsidiaries. On our world wide homepage all OSRAM subsidiaries are listed with complete address and phone numbers. Marcel-Breuer-Strasse 6 D - 80807 München Germany www.osram.com +49 (0)89 6213-0 Further Information Downloads: Eulumdat /IES files, CE declaration ST8V-0.6m – April 2015 Page 5 of 5 www.osram.com/SubstiTUBE