E M C C o m p o n e n t s December 2013 Common Mode Filters For high-speed differential signal line (USB2.0, LVDS, etc.) MCZ-AH series MCZ0806AH MCZ1210AH MCZ2010AH [0302 inch]* [0504 inch] [0804 inch] * Dimensions Code JIS[EIA] (2/11) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20131227 / e9712_mcz_ah.fm (3/11) E M C C o m p o n e n t s Common Mode Filters Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For high-speed differential signal line (USB2.0, LVDS, etc.) Overview of the MCZ-AH Series FEATURES Compact multilayer common mode filter. Has EMC suppression by achieving wide frequency range differential mode transmission while ensuring common mode impedance with virtually no affect on the high-speed differential transmission line signal. APPLICATION Electronic equipment high-speed interface (LVDS, USB2.0, MHL) Mobile phones, PCs, DSCs, portable game machines, etc. PDP/LCD/DLP/PJ TVs, DVD players, DVCs, mobile audio, etc. PART NUMBER CONSTRUCTION MCZ Series name 1210 L×W×T Dimensions (mm) 0806 0.85×0.65×0.45 1210 1.25×1.0×0.5 2010 2.0×1.0×0.5 AH 360 Product internal code AH Impedance (:) at 100MHz 360 36 L2 T Number of lines Packaging style L2 L4 2 lines 4 lines T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Type temperature temperature °C °C MCZ0806AH –40 to +85 –40 to +85 MCZ1210AH –40 to +85 –40 to +85 MCZ2010AH –40 to +85 –40 to +85 The Storage temperature range is for after the circuit board is mounted. Package quantity pieces/reel 10,000 4,000 5,000 Individual weight mg 1.4 3.0 5.0 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm (4/11) E M C C o m p o n e n t s Overview of the MCZ-AH Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s max. • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm (5/11) E M C C o m p o n e n t s MCZ-AH series MCZ0806AH Type SHAPE & DIMENSIONS 0.85±0.05 0.5±0.10 3 0.65±0.05 4 2 0.45±0.05 1 Dimensions in mm 0.27±0.10 RECOMMENDED LAND PATTERN 4 3 1 2 0.30 0.30 0.30 CIRCUIT DIAGRAM • No polarity 0.20 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm (6/11) E M C C o m p o n e n t s MCZ-AH series MCZ0806AH Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance [100MHz] (: ) Tolerance 22 ±8: 35 ±25% 50 ±25% 90 ±25% DC resistance (: )max. [1 line] 1.5 2.5 3.0 4.0 Rated current (mA)max. Rated voltage (V)max. 100 100 100 100 5 5 5 5 Measurement equipment Measurement item Product No. Common mode impedance E4991A+16192A DC resistance Type-7561 Insulation resistance 4339B Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 10 10 10 Part No. MCZ0806AH220L2T MCZ0806AH350L2T MCZ0806AH500L2T MCZ0806AH900L2T Manufacturer Agilent Technologies Yokogawa Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 Impedance (Ω) 1000 900 Common mode 500 Common mode 100 350 Common mode 220 Common mode 900 Differential mode 10 500 Differential mode 350 Differential mode 220 Differential mode 1 1 10 100 Frequency (MHz) 1000 10000 Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm (7/11) E M C C o m p o n e n t s MCZ-AH series MCZ1210AH Type SHAPE & DIMENSIONS 1.0±0.15 0.55±0.1 3 1.25±0.15 4 2 0.5±0.1 1 0.3±0.1 Dimensions in mm RECOMMENDED LAND PATTERN 4 3 1 2 0.7 to 0.75 0.5 0.3 CIRCUIT DIAGRAM • No polarity 0.25 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm (8/11) E M C C o m p o n e n t s MCZ-AH series MCZ1210AH Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance [100MHz] (: ) Tolerance 36 ±25% 90 ±25% 200 ±25% 300 ±25% DC resistance (: )max. [1 line] 1.00 1.75 4.00 4.50 Rated current (mA)max. Rated voltage (V)max. 200 100 100 100 5 5 5 5 Measurement equipment Measurement item Product No. Common mode impedance E4991A+16192A DC resistance Type-7561 Insulation resistance 4339B Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 10 10 10 Part No. MCZ1210AH360L2T MCZ1210AH900L2T MCZ1210AH201L2T MCZ1210AH301L2T Manufacturer Agilent Technologies Yokogawa Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 1000 Impedance (Ω) 301 Common mode 201 Common mode 900 Common mode 100 360 Common mode 301 Differential mode 10 201 Differential mode 900 Differential mode 360 Differential mode 1 1 10 100 Frequency (MHz) 1000 10000 Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm (9/11) E M C C o m p o n e n t s MCZ-AH series MCZ2010AH Type SHAPE & DIMENSIONS 2.0±0.15 0.5±0.1 7 6 5 3 4 1.0±0.15 0.2±0.15 8 2 0.5±0.1 1 0.25±0.1 Dimensions in mm CIRCUIT DIAGRAM 8 7 6 5 1 2 3 4 1.8 0.6 RECOMMENDED LAND PATTERN • No polarity 0.5 0.25 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm (10/11) E M C C o m p o n e n t s MCZ-AH series MCZ2010AH Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance [100MHz] (: ) Tolerance 90 ±25% 120 ±25% 200 ±25% DC resistance (: )max. [1 line] 1.50 2.00 3.50 Rated current (mA)max. Rated voltage (V)max. 100 100 100 5 5 5 Measurement equipment Measurement item Product No. Common mode impedance E4991A+16192A DC resistance Type-7561 Insulation resistance 4339B Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 10 10 Part No. MCZ2010AH900L4T MCZ2010AH121L4T MCZ2010AH201L4T Manufacturer Agilent Technologies Yokogawa Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 121 Differential mode 1000 201 Differential mode Impedance (Ω) 201 Common mode 121 Common mode 900 Common mode 100 900 Differential mode 10 1 1 10 100 Frequency (MHz) 1000 10000 Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm (11/11) E M C C o m p o n e n t s MCZ-AH series Packaging style REEL DIMENSIONS ø60min. 2.0±0.5 1.0 8.4 +2.0 –0.0 ø13±0.2 ø21±0.8 14.4max. ø180±2.0 Dimensions in mm TAPE DIMENSIONS P1 8.0±0.3 B A MCZ0806 MCZ1210 t 3.5±0.05 4.0±0.1 1.75±0.1 2.0±0.05 1.5 +0.1 0 MCZ2010 K K Dimensions in mm Type MCZ0806AH MCZ1210AH MCZ2010AH A 0.75±0.05 1.15±0.1 1.15±0.05 160min. Taping B 0.95±0.05 1.4±0.1 2.15±0.05 P1 2.0±0.05 4.0±0.1 4.0±0.1 K 0.6max. 1.0max. 0.86max. t 0.25±0.05 0.25±0.05 — 200min. Drawing direction 300min. Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20131227 / e9712_mcz_ah.fm