I N D U C T O R S September 2014 Inductors for Decoupling Circuits Multilayer Ferrite MLZseries MLZ1005 MLZ1608 MLZ2012 1005 [0402 inch]* 1608 [0603 inch] 2012 [0805 inch] * Dimensions Code JIS[EIA] (2/25) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20140903 / inductor_commercial_decoupling_mlz_en.fm (3/25) I N D U C T O R S Inductors for Decoupling Circuits Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Multilayer Ferrite Overview of the MLZ Series FEATURES The MLZ Series include inductors for decoupling circuits that have top-class DC superimposition characteristics and low DC resistance. Sizes range from 1005 to 2012, and they are compatible with wide frequency band noise, from low to high frequency. H type products have a rated current that is equivalent to that of wound coils. W type products are the new standard type products that have both large current and low resistance. L type products have a resistance up to 60% lower than W type products. APPLICATION Smart phones, tablet terminals, laptop computers, various modules such as camera modules, DSCs, video games, portable memory audio devices, navigation systems, PNDs, WLANs, SSDs PART NUMBER CONSTRUCTION MLZ Series name 1005 M R10 L×W×H Dimensions (mm) 1005 1.0×0.5×0.5 1608 1.6×0.8×0.8 2012 2.0×1.25×0.85 2012 2.0×1.25×1.25 Product internal code A D M N P Inductance (μH) R10 0.1 1R0 1 100 10 W T 000 Characteristic type Packaging style Internal code H D W L Ultra-large current type High frequency type Large current type Low resistance type T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type MLZ1005 MLZ1608 Temperature range Operating Storage temperature temperature （°C） （°C） –55 to +125 –55 to +125 –55 to +125 –55 to +125 Package quantity Individual weight (pieces/reel) 10000 4000 4000 2000 （mg） 1.2 4 10 14 t=0.85 –55 to +125 –55 to +125 t=1.25 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. MLZ2012 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (4/25) I N D U C T O R S Overview of the MLZ Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s max. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (5/25) I N D U C T O R S MLZ series MLZ1005 Type 0.50±0.05 SHAPE & DIMENSIONS 0.10min. 0.10min. 0.50±0.05 1.00±0.05 Dimensions in mm 0.5 RECOMMENDED LAND PATTERN 0.5 0.4 0.5 Dimensions in mm • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (6/25) I N D U C T O R S MLZ series MLZ1005 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Type Large current 1 2 (μH) Tolerance 0.47 0.68 1.00 1.50 2.20 ±20% ±20% ±20% ±20% ±20% L measuring conditions Frequency Current (MHz) (mA) 2 0.1 2 0.1 2 0.1 2 0.1 2 0.1 DC resistance ( )±30% Rated current1 (mA) Rated current2 (mA) Part No. 0.20 0.30 0.35 0.50 0.55 120 110 100 80 60 500 450 450 350 350 MLZ1005MR47WT000 MLZ1005MR68WT000 MLZ1005M1R0WT000 MLZ1005M1R5WT000 MLZ1005M2R2WT000 Current assumed when inductance ratio has decreased by 50% max.. Current assumed when temperature has risen to 20°C max. (reference value). Operating temperature environment at this time: 105°C max. ○ Measurement equipment Measurement item Product No. L 4294A+16034G DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Yokogawa • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (7/25) I N D U C T O R S MLZ series MLZ1005 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 10 2R2W 1R5W 1R0W R68W R47W Inductance(μH) 1 0.1 0.01 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer Agilent Technologies E4991A+16192Ａ ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (8/25) I N D U C T O R S MLZ series MLZ1005 Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 3.0 2R2W Inductance(μH) 2.0 1R5W 1R0W 1.0 R68W R47W 0.0 0 50 100 150 DC current(mA) ○ Measurement equipment Product No. Manufacturer 4291B+16200A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (9/25) I N D U C T O R S MLZ series MLZ1005 Type ELECTRICAL CHARACTERISTICS IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH 10000 2R2W 1R0W Impedance(Ω) 1000 1R5W R47W R68W 100 10 1 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (10/25) I N D U C T O R S MLZ series MLZ1608 Type 0.80±0.15 SHAPE & DIMENSIONS 0.30±0.20 0.30±0.20 0.80±0.15 1.60±0.15 Dimensions in mm 0.8 RECOMMENDED LAND PATTERN 0.6 0.8 0.6 Dimensions in mm • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (11/25) I N D U C T O R S MLZ series MLZ1608 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Type (μH) 0.10 0.22 0.47 1.00 2.20 Large 4.70 current 10.0 22.0 1.00 2.20 Low 4.70 resistance 10.0 22.0 High frequency 1 2 Tolerance ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% L measuring conditions Frequency Current (MHz) (mA) 25 1.0 25 1.0 25 1.0 10 1.0 10 1.0 2 0.1 2 0.1 2 0.1 2 0.1 2 0.1 2 0.1 2 0.1 2 0.1 DC resistance ( )±30% Rated current1 (mA) Rated current2 (mA) Part No. 0.14 0.27 0.42 0.15 0.25 0.50 1.05 2.40 0.11 0.18 0.32 0.60 1.65 700 550 400 190 130 120 90 55 140 110 80 60 50 850 600 500 600 500 350 250 150 700 500 400 300 190 MLZ1608DR10DT000 MLZ1608DR22DT000 MLZ1608DR47DT000 MLZ1608A1R0WT000 MLZ1608A2R2WT000 MLZ1608M4R7WT000 MLZ1608M100WT000 MLZ1608M220WT000 MLZ1608N1R0LT000 MLZ1608N2R2LT000 MLZ1608N4R7LT000 MLZ1608N100LT000 MLZ1608N220LT000 Current assumed when inductance ratio has decreased by 50% max.. Current assumed when temperature has risen to 20°C max. (reference value). Operating temperature environment at this time: 105°C max. ○ Measurement equipment Measurement item Product No. L 4294A+16034G DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Yokogawa • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (12/25) I N D U C T O R S MLZ series MLZ1608 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 M220W N220L M100W 10 N100L M4R7W N4R7L A2R2W Inductance(μH) N2R2L N1R0L 1 A1R0W DR47D DR22D DR10D 0.1 0.01 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer Agilent Technologies E4991A+16192Ａ ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (13/25) I N D U C T O R S MLZ series MLZ1608 Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 M220W N220L M100W 10 N100L M4R7W N4R7L Inductance(μH) A2R2W N2R2L 1 N1R0L A1R0W DR47D DR22D 0.1 DR10D 0.01 0 200 400 600 800 1000 DC current(mA) ○ Measurement equipment Product No. Manufacturer 4291B+16200A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (14/25) I N D U C T O R S MLZ series MLZ1608 Type ELECTRICAL CHARACTERISTICS IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH 100000 M220W 10000 M100W N220L M4R7W N100L DR47D N4R7L 1000 N2R2L Impedance(Ω) A2R2W A1R0W DR22D N1R0L DR10D 100 10 1 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (15/25) I N D U C T O R S MLZ series MLZ2012 Type 1.25±0.20 SHAPE & DIMENSIONS 0.50±0.30 0.50±0.30 T 2.00±0.20 T 0.85±0.20 1.25±0.20 Dimensions in mm 1.2 RECOMMENDED LAND PATTERN 0.8 1.0 0.8 Dimensions in mm • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (16/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Type (μH) 1.0 1.5 2.2 Ultra-large 3.3 current 4.7 6.8 10 0.10 High 0.22 frequency 0.47 1.00 1.50 2.20 3.30 4.70 6.80 Large current 10.0 15.0 22.0 22.0 33.0 47.0 1.00 1.50 2.20 3.30 4.70 Low resistance 6.80 10.0 15.0 22.0 100.0 1 2 L measuring conditions Thickness T Frequency Current Tolerance (mm) (MHz) (mA) ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 0.85 25 1.0 ±20% 0.85 25 1.0 ±20% 1.25 25 1.0 ±20% 0.85 10 1.0 ±20% 0.85 10 1.0 ±20% 0.85 10 1.0 ±20% 0.85 10 1.0 ±20% 0.85 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 0.85 2 0.1 ±20% 0.85 2 0.1 ±20% 0.85 2 0.1 ±20% 0.85 2 0.1 ±20% 0.85 2 0.1 ±20% 0.85 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 ±20% 1.25 2 0.1 Rated DC resistance current1 ( )±30% (mA) 0.10 700 0.14 550 0.16 400 0.20 350 0.34 300 0.40 220 0.68 200 0.07 1000 0.13 800 0.18 550 0.10 280 0.13 250 0.15 210 0.34 200 0.30 180 0.40 160 0.47 150 0.95 120 1.25 100 2.0 60 2.60 55 3.70 50 0.06 220 0.10 190 0.12 170 0.15 130 0.18 130 0.25 110 0.30 110 0.47 90 0.67 70 3.50 30 Rated current2 (mA) 800 700 600 500 400 350 300 1150 900 700 900 750 650 450 500 400 350 250 220 220 190 170 1150 900 800 750 600 550 500 350 300 140 Part No. MLZ2012M1R0HT000 MLZ2012M1R5HT000 MLZ2012M2R2HT000 MLZ2012M3R3HT000 MLZ2012M4R7HT000 MLZ2012M6R8HT000 MLZ2012M100HT000 MLZ2012DR10DT000 MLZ2012DR22DT000 MLZ2012DR47DT000 MLZ2012A1R0WT000 MLZ2012A1R5WT000 MLZ2012A2R2WT000 MLZ2012A3R3WT000 MLZ2012M4R7WT000 MLZ2012M6R8WT000 MLZ2012M100WT000 MLZ2012M150WT000 MLZ2012P220WT000 MLZ2012M220WT000 MLZ2012M330WT000 MLZ2012M470WT000 MLZ2012N1R0LT000 MLZ2012N1R5LT000 MLZ2012N2R2LT000 MLZ2012N3R3LT000 MLZ2012N4R7LT000 MLZ2012N6R8LT000 MLZ2012N100LT000 MLZ2012N150LT000 MLZ2012N220LT000 MLZ2012N101LT000 Current assumed when inductance ratio has decreased by 50% max.. Current assumed when temperature has risen to 20°C max. (reference value). Operating temperature environment at this time: 105°C max. ○ Measurement equipment Measurement item Product No. L 4294A+16034G DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Yokogawa • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (17/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT 100 M100H Inductance(μH) 10 M6R8H M4R7H M3R3H M2R2H M1R5H M1R0H 1 0.1 1 10 100 1000 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer Agilent Technologies E4991A+16192Ａ ＊ Equivalent measurement equipment may be used. L FREQUENCY CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT 1000 Inductance(μH) 100 10 1 DR47D DR22D DR10D 0.1 0.01 1 10 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (18/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH W CHARACTERISTIC PRODUCT 1000 M470W M330W P220W 100 M220W M150W M100W M6R8W Inductance(μH) 10 M4R7W A3R3W A2R2W 1 A1R5W A1R0W 0.1 0.01 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer Agilent Technologies E4991A+16192Ａ ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (19/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT 1000 N101L 100 N220L Inductance(μH) N150L N100L N6R8L 10 N4R7L N3R3L N2R2L N1R5L 1 N1R0L 0.1 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer Agilent Technologies E4991A+16192Ａ ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (20/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT 100 M100H Inductance(μH) 10 M6R8H M4R7H M3R3H M2R2H M1R5H M1R0H 1 0.1 0 200 400 600 800 1000 800 1000 DC current(mA) ○ Measurement equipment Product No. Manufacturer 4291B+16200A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT Inductance(μH) 10 1 DR47D DR22D 0.1 DR10D 0.01 0 200 400 600 DC current(mA) ○ Measurement equipment Product No. Manufacturer 4291B+16200A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (21/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH (EXAMPLE) W CHARACTERISTIC PRODUCT 1000 M330W 100 Inductance(μH) M470W P220W M100W 10 M4R7W M150W M220W 1 M6R8W 0.1 0 100 200 300 400 DC current(mA) 500 600 700 ○ Measurement equipment Product No. Manufacturer 4291B+16200A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT 1000 N101L Inductance(μH) 100 N220L 10 N150L N100L N6R8L N3R3L 1 N1R0L N4R7L N2R2L N1R5L 0.1 0 100 200 300 400 500 DC current(mA) ○ Measurement equipment Product No. Manufacturer 4291B+16200A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (22/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT 100000 M100H 10000 M6R8H M4R7H M3R3H M2R2H Impedance(Ω) M1R5H 1000 M1R0H 100 10 1 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT 10000 DR47D DR22D Impedance(Ω) 1000 DR10D 100 10 1 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (23/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH W CHARACTERISTIC PRODUCT 1000000 M330W 100000 P220W M220W M470W M150W 10000 M6R8W M100W Impedance(Ω) A3R3W 1000 A1R0W A1R5W A2R2W M4R7W 100 10 1 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (24/25) I N D U C T O R S MLZ series MLZ2012 Type ELECTRICAL CHARACTERISTICS IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT 100000 N101L Impedance(Ω) 10000 N220L N150L N100L 1000 N6R8L N1R0L 100 N4R7L N3R3L N2R2L N1R5L 10 1 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm (25/25) I N D U C T O R S MLZ series Packaging Style REEL DIMENSIONS ø60min. 1.0 2.0±0.5 8.4 +2.0 –0.0 ø13±0.2 14.4max. ø21±0.8 ø180±2.0 Dimensions in mm 4.0±0.1 B 4.0±0.1 A Type MLZ1005 MLZ1608 t=0.85 MLZ2012 t=1.25 160min. MLZ1005, MLZ1608, MLZ2012 (t=0.85) MLZ2012 (t=1.25) t 8.0±0.3 2.0±0.05 F 1.5 +0.1 0 1.75±0.1 TAPE DIMENSIONS A 1.15±0.1 1.9±0.2 2.3±0.2 2.3±0.2 Taping B 0.65±0.1 1.1±0.2 1.5±0.2 1.5±0.2 K K 0.8 max. 1.1 max. 1.1 max. 1.5 max. K Dimensions in mm t — — 200min. Drawing direction 300min. Dimensions in mm • All specifications are subject to change without notice. 20140903 / inductor_commercial_decoupling_mlz_en.fm