I N D U C T O R S November 2013 Transponder Coils TPL series TPL802727 TPL1183427 TPL1183525 (2/13) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. If an ultrasonic process is used, thoroughly check the condition setting in order to prevent disconnection. Do not clean the products with solvents. If a potting resin or a moisture-proof coat containing a solvent such as acetone, toluene or xylene is used, consult with us in advance. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (3/13) I N D U C T O R S Transponder Coils Product compatible with RoHS directive AEC-Q200 Overview of the TPL Series FEATURES Common in the series Transponder coils that ensure high reliability suitable for automotive applications. TPL802727 type coils also realize a small size (8 mm in length) and high inductance (18.52mH max.) Achieves stable electrical characteristics due to their high SRF design structure. TPL802727 type Ensures high reliability suitable for automotive applications by adopting higher heat resistance wire and welding wire connection. TPL1183427, TPL1183525 types It is fully resin-molded. Terminals are highly reliable with the spring structure. They show excellent quality especially in bending and drop resistance. APPLICATION Mainly receiving LF antenna coils for the in-car devices shown below Tire-pressure monitoring system (TPMS) Keyless entry system Immobilizer etc. Other electronic devices PART NUMBER CONSTRUCTION TPL Series name 802727 - L×W×H Dimensions (mm) 802727 8.0×2.7×2.7 1183427 11.8×3.4×2.75 1183525 11.8×3.5×2.4 722 H Inductance (mH) 722 7.2 Inductance tolerance (%) H ±3 J ±5 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage temperature temperature （°C） （°C） TPL802727 –40 to +125 –40 to +125 TPL1183427 –40 to +125 –40 to +125 TPL1183525 –40 to +125 –40 to +125 Operating temperature range includes self-temperature rise. Type Package quantity （pieces/reel） 2,500 2,500 2,500 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (4/13) I N D U C T O R S TPL series TPL802727 Type SHAPE & DIMENSIONS 2.7±0.2 2.7 –0.1 +0.3 7.85±0.15 0.8 1.9 Dimensions in mm 2.2 RECOMMENDED LAND PATTERN 5.3 9.5 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (5/13) I N D U C T O R S TPL series TPL802727 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Q (mH) 18.52 7.20 4.91 4.50 Tolerance ±3% ±3% ±3% ±3% min. 40 35 30 30 Measurement frequency (kHz) 125 125 125 125 DC resistance (: ) max. 240 105 85 80 Part No. TPL802727-193H TPL802727-722H TPL802727-492H TPL802727-452H This inductance value is an example of the current commercial product.If a different inductance is needed, please contact us. • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (6/13) I N D U C T O R S TPL series TPL802727 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 30 125kHz 722H 25 Inductance (mH) 193H 20 15 10 492H 5 0 10 452H 100 1000 10000 Frequency (kHz) Q FREQUENCY CHARACTERISTICS GRAPH 75 125kHz Q 50 193H 722H 25 492H 452H 0 10 100 1000 10000 Frequency (kHz) • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (7/13) I N D U C T O R S TPL series TPL1183427 Type SHAPE & DIMENSIONS 3.4±0.4 2.75±0.3 11.8±0.4 0.8 2.4 Dimensions in mm 2.7 RECOMMENDED LAND PATTERN 9.9 13.5 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (8/13) I N D U C T O R S TPL series TPL1183427 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Q Self-resonant frequency DC resistance L [125kHz] (kHz) (: ) [125kHz] Part No. (mH) Tolerance typ. typ. typ. 7.20 ±5% 66 690 50 TPL1183427-722J-720N This inductance value is an example of the current commercial product.If a different inductance is needed, please contact us. Available for an inductance tolerance of less than ±5%. ○ Measurement equipment Measurement item Product No. L, Q 4194A+16047E Self-resonant frequency 4194A+16047E DC resistance AX-114N ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies ADEX • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (9/13) I N D U C T O R S TPL series TPL1183427 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 125kHz 20 Inductance (mH) 15 10 5 0 10 100 Frequency (kHz) 1000 ○ Measurement equipment Product No. Manufacturer 4194A+16047E Agilent Technologies ＊ Equivalent measurement equipment may be used. Q FREQUENCY CHARACTERISTICS GRAPH 100 125kHz 80 Q 60 40 20 0 10 100 Frequency (MHz) 1000 ○ Measurement equipment Product No. Manufacturer 4194A+16047E Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (10/13) I N D U C T O R S TPL series TPL1183525 Type SHAPE & DIMENSIONS 3.5±0.4 2.4±0.3 11.8±0.5 0.8 3.2 Dimensions in mm 3.5 RECOMMENDED LAND PATTERN 9.9 13.5 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (11/13) I N D U C T O R S TPL series TPL1183525 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L [125kHz] (mH) 2.61 2.36 Tolerance ±5% ±3% Q [125kHz] typ. 50 53 Self-resonant frequency (kHz) typ. 650 1100 DC resistance (: ) typ. 26 24 Part No. TPL1183525-262J-261N TPL1183525-242Y-236N This inductance value is an example of the current commercial product.If a different inductance is needed, please contact us. Available for an inductance tolerance of less than ±5%. ○ Measurement equipment Measurement item Product No. L, Q 4194A+16047E Self-resonant frequency 4194A+16047E DC resistance AX-114N ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies ADEX • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (12/13) I N D U C T O R S TPL series TPL1183525 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 125kHz 20 Inductance (mH) 15 261N 236N 10 5 0 10 100 1000 10000 Frequency (kHz) ○ Measurement equipment Product No. Manufacturer 4194A+16047E Agilent Technologies ＊ Equivalent measurement equipment may be used. Q FREQUENCY CHARACTERISTICS GRAPH 100 125kHz 80 60 Q 236N 40 261N 20 0 10 100 1000 10000 Frequency (kHz) ○ Measurement equipment Product No. Manufacturer 4194A+16047E Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm (13/13) I N D U C T O R S TPL series Packaging style REEL DIMENSIONS 2.0±0.5 E Type A TPL802727 ø329+0.5/–1.5 W1 21.4±1.0 W2 17.4±1.0 ø330±2.0 24.4+2.0/–0 29±2.0 TPL1183525 ø330±2.0 24.4+2.0/–0 29±2.0 P2 2.0±0.1 2.0±0.1 2.0±0.1 W 16.0±0.3 24±0.3 24±0.3 E 2 2 2 N TPL1183427 N ø100±1.0 ø80 or ø100±1.0 ø80 or ø100±1.0 (1.0) ø13.0±0.5 W1 ø21.0±0.8 W2 A Dimensions in mm TAPE DIMENSIONS P2 P0 K P1 A B W F E øD0 t Dimensions in mm E 1.75±0.1 1.75±0.1 1.75±0.1 F 7.5±0.1 11.5±0.1 11.5±0.1 Dimensions in mm Type TPL802727 TPL1183427 TPL1183525 160min. A 3.0 3.7 3.7 Taping B 8.1 12.1 12.1 øD0 1.5+0.1/–0 1.55±0.05 1.55±0.05 P0 4.0±0.1 4.0±0.1 4.0±0.1 P1 8.0±0.1 8.0±0.1 8.0±0.1 K 2.9 3.2 2.8 t 0.3 0.3 0.3 200min. Drawing direction 300min. Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20131101 / e541_tpl.fm