Si1000/1/2/3/4/5

Si1000/1/2/3/4/5
Ultra Low Power, 64/32 kB, 10-Bit ADC
MCU with Integrated 240–960 MHz EZRadioPRO® Transceiver
Ultra Low Power: 0.9 to 3.6 V Operation
- Typical sleep mode current < 0.1 µA; retains state and
-
EZRadioPRO® Transceiver
-
10-Bit Analog to Digital Converter
- Up to 300 ksps
- Up to 18 external inputs
- External pin or internal VREF (no external capacitor
-
Digital Peripherals
- 19 or 16 port I/O plus 3 GPIO pins; Hardware enhanced
required)
Built-in temperature sensor
External conversion start input option
Autonomous burst mode with 16-bit automatic averaging
accumulator
Dual Comparators
- Programmable hysteresis and response time
- Configurable as interrupt or reset source
- Low current (< 0.5 µA)
On-Chip Debug
- On-chip debug circuitry facilitates full-speed, non-intrusive
in-system debug (No emulator required)
Clock Sources
- Precision internal oscillators: 24.5 MHz with ±2% accuracy
tions in 1 or 2 system clocks
Package
- 42-pin LGA (5 x 7 mm)
Temperature Range: –40 to +85 °C
programmable in 1024-byte sectors—1024 bytes are
reserved in the 64 kB devices
TEMP
SENSOR
VREF
VREG
IREF
+
+
–
–
VOLTAGE
COMPARATORS
DIGITAL I/O
UART
SMBus
SPI
PCA
Timer 0
Timer 1
Timer 2
Timer 3
CRC
Port 0
CROSSBAR
10-bit
300 ksps
ADC
supports UART operation; spread-spectrum mode for
reduced EMI; Low power 20 MHz internal oscillator
External oscillator: Crystal, RC, C, CMOS clock
SmaRTClock oscillator: 32.768 kHz crystal or self-oscillate
Can switch between clock sources on-the-fly; useful in
implementing various power saving modes
-
- Up to 25 MIPS throughput with 25 MHz clock
- Expanded interrupt handler
Memory
- 4352 bytes internal data RAM (256 + 4096)
- 64 kB (Si1000/2/4) or 32 kB (Si1001/3/5) flash; In-system
A
M
U
X
UART, SPI, and I2C serial ports available concurrently
Low power 32-bit SmaRTClock
Four general purpose 16-bit counter/timers; six channel
programmable counter array (PCA)
-
- Provides breakpoints, single stepping
- Inspect/modify memory and registers
- Complete development kit
High-Speed 8051 µC Core
- Pipelined instruction architecture; executes 70% of instruc-
ANALOG
PERIPHERALS
Frequency range = 240–960 MHz
Sensitivity = –121 dBm
FSK, GFSK, and OOK modulation
Max output power = +20 dBm (Si1000/1), +13 dBm
(Si1002/3/4/5)
RF power consumption
- 18.5 mA receive
- 18 mA @ +1 dBm transmit
- 30 mA @ +13 dBm transmit
- 85 mA @ +20 dBm transmit
Data rate = 0.123 to 256 kbps
Auto-frequency calibration (AFC)
Antenna diversity and transmit/receive switch control
Programmable packet handler
TX and RX 64 byte FIFOs
Frequency hopping capability
On-chip crystal tuning
-
RAM contents over full supply range; fast wakeup of < 2 µs
Less than 600 nA with RTC running
Less than 1 µA with RTC running and radio state retained
On-chip dc-dc converter allows operation down to 0.9 V.
Two built-in brown-out detectors cover sleep and active
modes
EZRadio
PRO
Serial
Interface
Port 1
PA
Mixer
PGA
ADC
20 MHz LOW POWER
INTERNAL OSCILLATOR
External Oscillator
HARDWARE smaRTClock
HIGH-SPEED CONTROLLER CORE
Rev. 1.3 2/13
LNA
Port 2
24.5 MHz PRECISION
INTERNAL OSCILLATOR
64/32 kB
ISP FLASH
FLEXIBLE
INTERRUPTS
EZRadioPRO
(240–960 MHz)
8051 CPU
(25 MIPS)
DEBUG
CIRCUITRY
4352 B
SRAM
POR
Digital
Modem
PLL
Delta
Sigma
Modulator
Digital
Logic
OSC
WDT
Copyright © 2013 by Silicon Laboratories
Si1000/1/2/3/4/5
Si1000/1/2/3/4/5
2
Rev. 1.3
Si1000/1/2/3/4/5
Table of Contents
1. System Overview ..................................................................................................... 17
1.1. Typical Connection Diagram ............................................................................. 21
1.2. CIP-51™ Microcontroller Core .......................................................................... 22
1.3. Port Input/Output ............................................................................................... 23
1.4. Serial Ports ........................................................................................................ 24
1.5. Programmable Counter Array............................................................................ 24
1.6. 10-bit SAR ADC with 16-bit Auto-Averaging Accumulator and 
Autonomous Low Power Burst Mode................................................................ 25
1.7. Programmable Current Reference (IREF0)....................................................... 26
1.8. Comparators...................................................................................................... 26
2. Ordering Information ............................................................................................... 28
3. Pinout and Package Definitions ............................................................................. 29
4. Electrical Characteristics ........................................................................................ 40
4.1. Absolute Maximum Specifications..................................................................... 40
4.2. MCU Electrical Characteristics .......................................................................... 41
4.3. EZRadioPRO® Electrical Characteristics .......................................................... 66
4.4. Definition of Test Conditions for the EZRadioPRO Peripheral .......................... 73
5. 10-Bit SAR ADC with 16-bit Auto-Averaging Accumulator and 
Autonomous Low Power Burst Mode ................................................................... 74
5.1. Output Code Formatting .................................................................................... 74
5.2. Modes of Operation ........................................................................................... 76
5.3. 8-Bit Mode ......................................................................................................... 81
5.4. Programmable Window Detector....................................................................... 88
5.5. ADC0 Analog Multiplexer .................................................................................. 91
5.6. Temperature Sensor.......................................................................................... 93
5.7. Voltage and Ground Reference Options ........................................................... 96
5.8. External Voltage References............................................................................. 97
5.9. Internal Voltage References .............................................................................. 97
5.10. Analog Ground Reference............................................................................... 97
5.11. Temperature Sensor Enable ........................................................................... 97
5.12. Voltage Reference Electrical Specifications .................................................... 98
6. Programmable Current Reference (IREF0)............................................................ 99
6.1. IREF0 Specifications ......................................................................................... 99
7. Comparators........................................................................................................... 100
7.1. Comparator Inputs........................................................................................... 100
7.2. Comparator Outputs ........................................................................................ 101
7.3. Comparator Response Time ........................................................................... 102
7.4. Comparator Hysteresis.................................................................................... 102
7.5. Comparator Register Descriptions .................................................................. 103
7.6. Comparator0 and Comparator1 Analog Multiplexers ...................................... 107
8. CIP-51 Microcontroller........................................................................................... 110
8.1. Performance .................................................................................................... 110
8.2. Programming and Debugging Support ............................................................ 111
Rev. 1.3
3
Si1000/1/2/3/4/5
8.3. Instruction Set.................................................................................................. 111
8.4. CIP-51 Register Descriptions .......................................................................... 116
9. Memory Organization ............................................................................................ 119
9.1. Program Memory............................................................................................. 120
9.2. Data Memory ................................................................................................... 120
10. On-Chip XRAM ..................................................................................................... 122
10.1. Accessing XRAM........................................................................................... 122
10.2. Special Function Registers............................................................................ 123
11. Special Function Registers................................................................................. 124
11.1. SFR Paging ................................................................................................... 125
12. Interrupt Handler.................................................................................................. 130
12.1. Enabling Interrupt Sources ............................................................................ 130
12.2. MCU Interrupt Sources and Vectors.............................................................. 130
12.3. Interrupt Priorities .......................................................................................... 131
12.4. Interrupt Latency............................................................................................ 131
12.5. Interrupt Register Descriptions ...................................................................... 133
12.6. External Interrupts INT0 and INT1................................................................. 140
13. Flash Memory....................................................................................................... 142
13.1. Programming the Flash Memory ................................................................... 142
13.2. Non-volatile Data Storage ............................................................................. 144
13.3. Security Options ............................................................................................ 144
13.4. Determining the Device Part Number at Run Time ....................................... 146
13.5. Flash Write and Erase Guidelines ................................................................. 146
13.6. Minimizing Flash Read Current ..................................................................... 148
14. Power Management ............................................................................................. 152
14.1. Normal Mode ................................................................................................. 153
14.2. Idle Mode....................................................................................................... 154
14.3. Stop Mode ..................................................................................................... 154
14.4. Suspend Mode .............................................................................................. 155
14.5. Sleep Mode ................................................................................................... 155
14.6. Configuring Wakeup Sources........................................................................ 156
14.7. Determining the Event that Caused the Last Wakeup................................... 156
14.8. Power Management Specifications ............................................................... 158
15. Cyclic Redundancy Check Unit (CRC0)............................................................. 159
15.1. 16-bit CRC Algorithm..................................................................................... 159
15.2. 32-bit CRC Algorithm..................................................................................... 161
15.3. Preparing for a CRC Calculation ................................................................... 163
15.4. Performing a CRC Calculation ...................................................................... 163
15.5. Accessing the CRC0 Result .......................................................................... 163
15.6. CRC0 Bit Reverse Feature............................................................................ 167
16. On-Chip DC-DC Converter (DC0)........................................................................ 168
16.1. Startup Behavior............................................................................................ 169
16.2. High Power Applications ............................................................................ 170
16.3. Pulse Skipping Mode..................................................................................... 170
16.4. Enabling the DC-DC Converter ..................................................................... 170
4
Rev. 1.3
Si1000/1/2/3/4/5
16.5. Minimizing Power Supply Noise .................................................................... 172
16.6. Selecting the Optimum Switch Size............................................................... 172
16.7. DC-DC Converter Clocking Options .............................................................. 172
16.8. DC-DC Converter Behavior in Sleep Mode ................................................... 173
16.9. DC-DC Converter Register Descriptions ....................................................... 174
16.10. DC-DC Converter Specifications ................................................................. 176
17. Voltage Regulator (VREG0)................................................................................. 177
17.1. Voltage Regulator Electrical Specifications ................................................... 177
18. Reset Sources ...................................................................................................... 178
18.1. Power-On (VBAT Supply Monitor) Reset ...................................................... 179
18.2. Power-Fail (VDD_MCU Supply Monitor) Reset............................................. 180
18.3. External Reset ............................................................................................... 182
18.4. Missing Clock Detector Reset ....................................................................... 182
18.5. Comparator0 Reset ....................................................................................... 183
18.6. PCA Watchdog Timer Reset ......................................................................... 183
18.7. Flash Error Reset .......................................................................................... 183
18.8. SmaRTClock (Real Time Clock) Reset ......................................................... 183
18.9. Software Reset .............................................................................................. 183
19. Clocking Sources................................................................................................. 185
19.1. Programmable Precision Internal Oscillator .................................................. 186
19.2. Low Power Internal Oscillator........................................................................ 186
19.3. External Oscillator Drive Circuit..................................................................... 186
19.4. Special Function Registers for Selecting and Configuring the 
System Clock................................................................................................. 190
20. SmaRTClock (Real Time Clock).......................................................................... 193
20.1. SmaRTClock Interface .................................................................................. 193
20.2. SmaRTClock Clocking Sources .................................................................... 200
20.3. SmaRTClock Timer and Alarm Function ....................................................... 204
21. Port Input/Output ................................................................................................. 210
21.1. Port I/O Modes of Operation.......................................................................... 211
21.2. Assigning Port I/O Pins to Analog and Digital Functions............................... 212
21.3. Priority Crossbar Decoder ............................................................................. 214
21.4. Port Match ..................................................................................................... 219
21.5. Special Function Registers for Accessing and Configuring Port I/O ............. 222
22. EZRadioPRO® Serial Interface (SPI1) ................................................................ 231
22.1. Signal Descriptions........................................................................................ 232
22.2. SPI Master Operation on the MCU Core Side............................................... 232
22.3. SPI Slave Operation on the EZRadioPRO Peripheral Side........................... 232
22.4. EZRadioPRO Serial Interface Interrupt Sources ........................................... 235
22.5. Serial Clock Phase and Polarity .................................................................... 235
22.6. SPI Special Function Registers ..................................................................... 236
23. EZRadioPRO® 240–960 MHz Transceiver.......................................................... 242
23.1. EZRadioPRO Operating Modes .................................................................... 243
23.2. Interrupts ...................................................................................................... 246
23.3. System Timing............................................................................................... 247
Rev. 1.3
5
Si1000/1/2/3/4/5
23.4. Modulation Options........................................................................................ 254
23.5. Internal Functional Blocks ............................................................................. 259
23.6. Data Handling and Packet Handler ............................................................... 264
23.7. RX Modem Configuration .............................................................................. 272
23.8. Auxiliary Functions ........................................................................................ 272
23.9. Reference Design.......................................................................................... 285
23.10. Application Notes and Reference Designs .................................................. 287
23.11. Customer Support ....................................................................................... 287
23.12. Register Table and Descriptions ................................................................. 288
23.13. Required Changes to Default Register Values............................................ 290
24. SMBus................................................................................................................... 291
24.1. Supporting Documents .................................................................................. 292
24.2. SMBus Configuration..................................................................................... 292
24.3. SMBus Operation .......................................................................................... 292
24.4. Using the SMBus........................................................................................... 294
24.5. SMBus Transfer Modes................................................................................. 306
24.6. SMBus Status Decoding................................................................................ 309
25. UART0 ................................................................................................................... 314
25.1. Enhanced Baud Rate Generation.................................................................. 315
25.2. Operational Modes ........................................................................................ 316
25.3. Multiprocessor Communications ................................................................... 317
26. Enhanced Serial Peripheral Interface (SPI0) ..................................................... 322
26.1. Signal Descriptions........................................................................................ 323
26.2. SPI0 Master Mode Operation ........................................................................ 323
26.3. SPI0 Slave Mode Operation .......................................................................... 325
26.4. SPI0 Interrupt Sources .................................................................................. 326
26.5. Serial Clock Phase and Polarity .................................................................... 327
26.6. SPI Special Function Registers ..................................................................... 328
27. Timers ................................................................................................................... 335
27.1. Timer 0 and Timer 1 ...................................................................................... 337
27.2. Timer 2 .......................................................................................................... 345
27.3. Timer 3 .......................................................................................................... 351
28. Programmable Counter Array............................................................................. 357
28.1. PCA Counter/Timer ....................................................................................... 358
28.2. PCA0 Interrupt Sources................................................................................. 359
28.3. Capture/Compare Modules ........................................................................... 360
28.4. Watchdog Timer Mode .................................................................................. 368
28.5. Register Descriptions for PCA0..................................................................... 370
29. Device Specific Behavior .................................................................................... 376
29.1. Device Identification ...................................................................................... 376
30. C2 Interface .......................................................................................................... 377
30.1. C2 Interface Registers................................................................................... 377
30.2. C2 Pin Sharing .............................................................................................. 380
Document Change List.............................................................................................. 381
Contact Information................................................................................................... 382
6
Rev. 1.3
Si1000/1/2/3/4/5
List of Figures
Figure 1.1. Si1000 Block Diagram ........................................................................... 18
Figure 1.2. Si1001 Block Diagram ........................................................................... 18
Figure 1.3. Si1002 Block Diagram ........................................................................... 19
Figure 1.4. Si1003 Block Diagram ........................................................................... 19
Figure 1.5. Si1004 Block Diagram ........................................................................... 20
Figure 1.6. Si1005 Block Diagram ........................................................................... 20
Figure 1.7. Si1002/3 RX/TX Direct-tie Application Example .................................... 21
Figure 1.8. Si1000/1 Antenna Diversity Application Example ................................. 21
Figure 1.9. Port I/O Functional Block Diagram ........................................................ 23
Figure 1.10. PCA Block Diagram ............................................................................. 24
Figure 1.11. ADC0 Functional Block Diagram ......................................................... 25
Figure 1.12. ADC0 Multiplexer Block Diagram ........................................................ 26
Figure 1.13. Comparator 0 Functional Block Diagram ............................................ 27
Figure 1.14. Comparator 1 Functional Block Diagram ............................................ 27
Figure 3.1. Si100/1/2/3-E-GM2 Pinout Diagram (Top View) ................................... 33
Figure 3.2. Si1004/5-E-GM2 Pinout Diagram (Top View) ....................................... 34
Figure 3.3. LGA-42 Package Drawing (Si1000/1/2/3/4/5-E-GM2) ........................... 35
Figure 3.4. LGA-42 PCB Land Pattern Dimensions (Si1000/1/2/3/4/5-E-GM2) ...... 37
Figure 3.5. LGA-42 PCB Stencil and Via Placement ............................................... 39
Figure 4.1. Active Mode Current (External CMOS Clock) ....................................... 44
Figure 4.2. Idle Mode Current (External CMOS Clock) ........................................... 45
Figure 4.3. Typical DC-DC Converter Efficiency 
(High Current, VDD/DC+ = 2 V ............................................................. 46
Figure 4.4. Typical DC-DC Converter Efficiency 
(High Current, VDD/DC+ = 3 V) ............................................................ 47
Figure 4.5. Typical DC-DC Converter Efficiency 
(Low Current, VDD/DC+ = 2 V) ............................................................. 48
Figure 4.6. Typical One-Cell Suspend Mode Current .............................................. 49
Figure 4.7. Typical VOH Curves, 1.8–3.6 V ............................................................ 51
Figure 4.8. Typical VOH Curves, 0.9–1.8 V ............................................................ 52
Figure 4.9. Typical VOL Curves, 1.8–3.6 V ............................................................. 53
Figure 4.10. Typical VOL Curves, 1.8–3.6 V ........................................................... 54
Figure 4.11. Typical VOL Curves, 0.9–1.8 V ........................................................... 55
Figure 5.1. ADC0 Functional Block Diagram ........................................................... 74
Figure 5.2. 10-Bit ADC Track and Conversion Example Timing 
(BURSTEN = 0) ..................................................................................... 77
Figure 5.3. Burst Mode Tracking Example with Repeat Count Set to 4 .................. 79
Figure 5.4. ADC0 Equivalent Input Circuits ............................................................. 80
Figure 5.5. ADC Window Compare Example: Right-Justified 
Single-Ended Data ................................................................................ 90
Figure 5.6. ADC Window Compare Example: Left-Justified 
Single-Ended Data ................................................................................ 90
Figure 5.7. ADC0 Multiplexer Block Diagram .......................................................... 91
Rev. 1.3
7
Si1000/1/2/3/4/5
Figure 5.8. Temperature Sensor Transfer Function ................................................ 93
Figure 5.9. Temperature Sensor Error with 1-Point Calibration 
(VREF = 1.68 V) ..................................................................................... 94
Figure 5.10. Voltage Reference Functional Block Diagram ..................................... 96
Figure 7.1. Comparator 0 Functional Block Diagram ............................................ 100
Figure 7.2. Comparator 1 Functional Block Diagram ............................................ 101
Figure 7.3. Comparator Hysteresis Plot ................................................................ 102
Figure 7.4. CPn Multiplexer Block Diagram ........................................................... 107
Figure 8.1. CIP-51 Block Diagram ......................................................................... 110
Figure 9.1. Si1000/1/2/3/4/5 Memory Map ............................................................ 119
Figure 9.2. Flash Program Memory Map ............................................................... 120
Figure 13.1. Flash Program Memory Map ............................................................. 144
Figure 14.1. Si1000/1/2/3/4/5 Power Distribution .................................................. 153
Figure 15.1. CRC0 Block Diagram ........................................................................ 159
Figure 15.2. Bit Reverse Register ......................................................................... 167
Figure 16.1. DC-DC Converter Block Diagram ...................................................... 168
Figure 16.2. DC-DC Converter Configuration Options .......................................... 171
Figure 18.1. Reset Sources ................................................................................... 178
Figure 18.2. Power-Fail Reset Timing Diagram .................................................... 179
Figure 18.3. Power-Fail Reset Timing Diagram .................................................... 180
Figure 19.1. Clocking Sources Block Diagram ...................................................... 185
Figure 19.2. 25 MHz External Crystal Example ..................................................... 187
Figure 20.1. SmaRTClock Block Diagram ............................................................. 193
Figure 20.2. Interpreting Oscillation Robustness (Duty Cycle) Test Results ......... 202
Figure 21.1. Port I/O Functional Block Diagram .................................................... 210
Figure 21.2. Port I/O Cell Block Diagram .............................................................. 211
Figure 21.3. Crossbar Priority Decoder with No Pins Skipped .............................. 215
Figure 21.4. Crossbar Priority Decoder with Crystal Pins Skipped ....................... 216
Figure 22.1. EZRadioPRO Serial Interface Block Diagram ................................... 231
Figure 22.2. SPI Timing ......................................................................................... 233
Figure 22.3. SPI Timing—READ Mode ................................................................. 233
Figure 22.4. SPI Timing—Burst Write Mode ......................................................... 234
Figure 22.5. SPI Timing—Burst Read Mode ......................................................... 234
Figure 22.6. Master Mode Data/Clock Timing ....................................................... 235
Figure 22.7. SPI Master Timing ............................................................................. 241
Figure 23.1. State Machine Diagram ..................................................................... 244
Figure 23.2. TX Timing .......................................................................................... 247
Figure 23.3. RX Timing .......................................................................................... 248
Figure 23.4. Frequency Deviation ......................................................................... 251
Figure 23.5. Sensitivity at 1% PER vs. Carrier Frequency Offset ......................... 253
Figure 23.6. FSK vs. GFSK Spectrums ................................................................. 255
Figure 23.7. Direct Synchronous Mode Example .................................................. 258
Figure 23.8. Direct Asynchronous Mode Example ................................................ 258
Figure 23.9. Microcontroller Connections .............................................................. 259
Figure 23.10. PLL Synthesizer Block Diagram ...................................................... 261
8
Rev. 1.3
Si1000/1/2/3/4/5
Figure 23.11. FIFO Thresholds ............................................................................. 264
Figure 23.12. Packet Structure .............................................................................. 265
Figure 23.13. Multiple Packets in TX Packet Handler ........................................... 266
Figure 23.14. Required RX Packet Structure with Packet Handler Disabled ........ 266
Figure 23.15. Multiple Packets in RX Packet Handler ........................................... 267
Figure 23.16. Multiple Packets in RX with CRC or Header Error .......................... 267
Figure 23.17. Operation of Data Whitening, Manchester Encoding, and CRC ..... 269
Figure 23.18. Manchester Coding Example .......................................................... 269
Figure 23.19. Header ............................................................................................. 271
Figure 23.20. POR Glitch Parameters ................................................................... 272
Figure 23.21. General Purpose ADC Architecture ................................................ 275
Figure 23.22. Temperature Ranges using ADC8 .................................................. 277
Figure 23.23. WUT Interrupt and WUT Operation ................................................. 280
Figure 23.24. Low Duty Cycle Mode ..................................................................... 281
Figure 23.25. RSSI Value vs. Input Power ............................................................ 284
Figure 23.26. Si1002 Split RF TX/RX Direct-Tie 
Reference Design—Schematic ....................................................... 285
Figure 23.27. Si1000 Switch Matching Reference Design—Schematic ................ 286
Figure 24.1. SMBus Block Diagram ...................................................................... 291
Figure 24.2. Typical SMBus Configuration ............................................................ 292
Figure 24.3. SMBus Transaction ........................................................................... 293
Figure 24.4. Typical SMBus SCL Generation ........................................................ 295
Figure 24.5. Typical Master Write Sequence ........................................................ 306
Figure 24.6. Typical Master Read Sequence ........................................................ 307
Figure 24.7. Typical Slave Write Sequence .......................................................... 308
Figure 24.8. Typical Slave Read Sequence .......................................................... 309
Figure 25.1. UART0 Block Diagram ...................................................................... 314
Figure 25.2. UART0 Baud Rate Logic ................................................................... 315
Figure 25.3. UART Interconnect Diagram ............................................................. 316
Figure 25.4. 8-Bit UART Timing Diagram .............................................................. 316
Figure 25.5. 9-Bit UART Timing Diagram .............................................................. 317
Figure 25.6. UART Multi-Processor Mode Interconnect Diagram ......................... 318
Figure 26.1. SPI Block Diagram ............................................................................ 322
Figure 26.2. Multiple-Master Mode Connection Diagram ...................................... 324
Figure 26.3. 3-Wire Single Master and 3-Wire Single Slave Mode 
Connection Diagram ......................................................................... 324
Figure 26.4. 4-Wire Single Master Mode and 4-Wire Slave Mode 
Connection Diagram ......................................................................... 325
Figure 26.5. Master Mode Data/Clock Timing ....................................................... 327
Figure 26.6. Slave Mode Data/Clock Timing (CKPHA = 0) ................................... 328
Figure 26.7. Slave Mode Data/Clock Timing (CKPHA = 1) ................................... 328
Figure 26.8. SPI Master Timing (CKPHA = 0) ....................................................... 332
Figure 26.9. SPI Master Timing (CKPHA = 1) ....................................................... 332
Figure 26.10. SPI Slave Timing (CKPHA = 0) ....................................................... 333
Figure 26.11. SPI Slave Timing (CKPHA = 1) ....................................................... 333
Rev. 1.3
9
Si1000/1/2/3/4/5
Figure 27.1. T0 Mode 0 Block Diagram ................................................................. 338
Figure 27.2. T0 Mode 2 Block Diagram ................................................................. 339
Figure 27.3. T0 Mode 3 Block Diagram ................................................................. 340
Figure 27.4. Timer 2 16-Bit Mode Block Diagram ................................................. 345
Figure 27.5. Timer 2 8-Bit Mode Block Diagram ................................................... 346
Figure 27.6. Timer 2 Capture Mode Block Diagram .............................................. 347
Figure 27.7. Timer 3 16-Bit Mode Block Diagram ................................................. 351
Figure 27.8. Timer 3 8-Bit Mode Block Diagram. .................................................. 352
Figure 27.9. Timer 3 Capture Mode Block Diagram .............................................. 353
Figure 28.1. PCA Block Diagram ........................................................................... 357
Figure 28.2. PCA Counter/Timer Block Diagram ................................................... 358
Figure 28.3. PCA Interrupt Block Diagram ............................................................ 359
Figure 28.4. PCA Capture Mode Diagram ............................................................. 361
Figure 28.5. PCA Software Timer Mode Diagram ................................................. 362
Figure 28.6. PCA High-Speed Output Mode Diagram ........................................... 363
Figure 28.7. PCA Frequency Output Mode ........................................................... 364
Figure 28.8. PCA 8-Bit PWM Mode Diagram ........................................................ 365
Figure 28.9. PCA 9, 10 and 11-Bit PWM Mode Diagram ...................................... 366
Figure 28.10. PCA 16-Bit PWM Mode ................................................................... 367
Figure 28.11. PCA Module 5 with Watchdog Timer Enabled ................................ 368
Figure 29.1. Si100x Revision Information .............................................................. 376
Figure 30.1. Typical C2 Pin Sharing ...................................................................... 380
10
Rev. 1.3
Si1000/1/2/3/4/5
List of Tables
Table 2.1. Product Selection Guide ......................................................................... 28
Table 3.1. Pin Definitions for the Si1000/1/2/3/4/5 .................................................. 29
Table 3.2. LGA-42 Package Dimensions (Si1000/1/2/3/4/5-E-GM2) ...................... 36
Table 3.3. LGA-42 PCB Land Pattern Dimensions (Si1000/1/2/3/4/5-E-GM2) ....... 38
Table 4.1. Absolute Maximum Ratings .................................................................... 40
Table 4.2. Global Electrical Characteristics ............................................................. 41
Table 4.3. Port I/O DC Electrical Characteristics ..................................................... 50
Table 4.4. Reset Electrical Characteristics .............................................................. 56
Table 4.5. Power Management Electrical Specifications ......................................... 57
Table 4.6. Flash Electrical Characteristics .............................................................. 57
Table 4.7. Internal Precision Oscillator Electrical Characteristics ........................... 58
Table 4.8. Internal Low-Power Oscillator Electrical Characteristics ........................ 58
Table 4.9. ADC0 Electrical Characteristics .............................................................. 59
Table 4.10. Temperature Sensor Electrical Characteristics .................................... 60
Table 4.11. Voltage Reference Electrical Characteristics ....................................... 60
Table 4.12. IREF0 Electrical Characteristics ........................................................... 61
Table 4.13. Comparator Electrical Characteristics .................................................. 62
Table 4.14. DC-DC Converter (DC0) Electrical Characteristics .............................. 64
Table 4.15. VREG0 Electrical Characteristics ......................................................... 65
Table 4.16. DC Characteristics ................................................................................ 66
Table 4.17. Synthesizer AC Electrical Characteristics ............................................ 67
Table 4.18. Receiver AC Electrical Characteristics ................................................. 68
Table 4.19. Transmitter AC Electrical Characteristics ............................................. 69
Table 4.20. Auxiliary Block Specifications ................................................................ 70
Table 4.21. Digital IO Specifications (nIRQ) ............................................................ 71
Table 4.22. GPIO Specifications (GPIO_0, GPIO_1, and GPIO_2) ........................ 71
Table 4.23. Absolute Maximum Ratings .................................................................. 72
Table 8.1. CIP-51 Instruction Set Summary .......................................................... 112
Table 11.1. Special Function Register (SFR) Memory Map (Page 0x0) ............... 124
Table 11.2. Special Function Register (SFR) Memory Map (Page 0xF) ............... 125
Table 11.3. Special Function Registers ................................................................. 126
Table 12.1. Interrupt Summary .............................................................................. 132
Table 13.1. Flash Security Summary .................................................................... 145
Table 14.1. Power Modes ...................................................................................... 152
Table 15.1. Example 16-bit CRC Outputs ............................................................. 160
Table 15.2. Example 32-bit CRC Outputs ............................................................. 162
Table 16.1. IPeak Inductor Current Limit Settings ................................................. 169
Table 19.1. Recommended XFCN Settings for Crystal Mode ............................... 187
Table 19.2. Recommended XFCN Settings for RC and C modes ......................... 188
Table 20.1. SmaRTClock Internal Registers ......................................................... 194
Table 20.2. SmaRTClock Load Capacitance Settings .......................................... 201
Table 20.3. SmaRTClock Bias Settings ................................................................ 203
Table 21.1. Port I/O Assignment for Analog Functions ......................................... 213
Rev. 1.3
11
Si1000/1/2/3/4/5
Table 21.2. Port I/O Assignment for Digital Functions ........................................... 213
Table 21.3. Port I/O Assignment for External Digital Event Capture Functions .... 214
Table 22.1. Serial Interface Timing Parameters .................................................... 233
Table 22.2. SPI Timing Parameters ...................................................................... 241
Table 23.1. EZRadioPRO Operating Modes ......................................................... 243
Table 23.2. EZRadioPRO Operating Modes Response Time ............................... 244
Table 23.3. Frequency Band Selection ................................................................. 249
Table 23.4. Packet Handler Registers ................................................................... 268
Table 23.5. Minimum Receiver Settling Time ........................................................ 270
Table 23.6. POR Parameters ................................................................................ 273
Table 23.7. Temperature Sensor Range ............................................................... 276
Table 23.8. Antenna Diversity Control ................................................................... 283
Table 23.9. EZRadioPRO Internal Register Descriptions ...................................... 288
Table 24.1. SMBus Clock Source Selection .......................................................... 295
Table 24.2. Minimum SDA Setup and Hold Times ................................................ 296
Table 24.3. Sources for Hardware Changes to SMB0CN ..................................... 300
Table 24.4. Hardware Address Recognition Examples (EHACK = 1) ................... 301
Table 24.5. SMBus Status Decoding With Hardware ACK Generation Disabled
(EHACK = 0) ....................................................................................... 310
Table 24.6. SMBus Status Decoding With Hardware ACK Generation Enabled
(EHACK = 1) ....................................................................................... 312
Table 25.1. Timer Settings for Standard Baud Rates 
Using The Internal 24.5 MHz Oscillator .............................................. 321
Table 25.2. Timer Settings for Standard Baud Rates 
Using an External 22.1184 MHz Oscillator ......................................... 321
Table 26.1. SPI Slave Timing Parameters ............................................................ 334
Table 27.1. Timer 0 Running Modes ..................................................................... 337
Table 28.1. PCA Timebase Input Options ............................................................. 358
Table 28.2. PCA0CPM and PCA0PWM Bit Settings for PCA 
Capture/Compare Modules ................................................................ 360
Table 28.3. Watchdog Timer Timeout Intervals1 ................................................... 369
12
Rev. 1.3
Si1000/1/2/3/4/5
List of Registers
SFR Definition 5.1. ADC0CN: ADC0 Control ................................................................ 82
SFR Definition 5.2. ADC0CF: ADC0 Configuration ...................................................... 83
SFR Definition 5.3. ADC0AC: ADC0 Accumulator Configuration ................................. 84
SFR Definition 5.4. ADC0PWR: ADC0 Burst Mode Power-Up Time ............................ 85
SFR Definition 5.5. ADC0TK: ADC0 Burst Mode Track Time ....................................... 86
SFR Definition 5.6. ADC0H: ADC0 Data Word High Byte ............................................ 87
SFR Definition 5.7. ADC0L: ADC0 Data Word Low Byte .............................................. 87
SFR Definition 5.8. ADC0GTH: ADC0 Greater-Than High Byte ................................... 88
SFR Definition 5.9. ADC0GTL: ADC0 Greater-Than Low Byte .................................... 88
SFR Definition 5.10. ADC0LTH: ADC0 Less-Than High Byte ...................................... 89
SFR Definition 5.11. ADC0LTL: ADC0 Less-Than Low Byte ........................................ 89
SFR Definition 5.12. ADC0MX: ADC0 Input Channel Select ........................................ 92
SFR Definition 5.13. TOFFH: ADC0 Data Word High Byte .......................................... 95
SFR Definition 5.14. TOFFL: ADC0 Data Word Low Byte ............................................ 95
SFR Definition 5.15. REF0CN: Voltage Reference Control .......................................... 98
SFR Definition 6.1. IREF0CN: Current Reference Control ........................................... 99
SFR Definition 7.1. CPT0CN: Comparator 0 Control .................................................. 103
SFR Definition 7.2. CPT0MD: Comparator 0 Mode Selection .................................... 104
SFR Definition 7.3. CPT1CN: Comparator 1 Control .................................................. 105
SFR Definition 7.4. CPT1MD: Comparator 1 Mode Selection .................................... 106
SFR Definition 7.5. CPT0MX: Comparator0 Input Channel Select ............................. 108
SFR Definition 7.6. CPT1MX: Comparator1 Input Channel Select ............................. 109
SFR Definition 8.1. DPL: Data Pointer Low Byte ........................................................ 116
SFR Definition 8.2. DPH: Data Pointer High Byte ....................................................... 116
SFR Definition 8.3. SP: Stack Pointer ......................................................................... 117
SFR Definition 8.4. ACC: Accumulator ....................................................................... 117
SFR Definition 8.5. B: B Register ................................................................................ 117
SFR Definition 8.6. PSW: Program Status Word ........................................................ 118
SFR Definition 10.1. EMI0CN: External Memory Interface Control ............................ 123
SFR Definition 11.1. SFRPage: SFR Page ................................................................. 126
SFR Definition 12.1. IE: Interrupt Enable .................................................................... 134
SFR Definition 12.2. IP: Interrupt Priority .................................................................... 135
SFR Definition 12.3. EIE1: Extended Interrupt Enable 1 ............................................ 136
SFR Definition 12.4. EIP1: Extended Interrupt Priority 1 ............................................ 137
SFR Definition 12.5. EIE2: Extended Interrupt Enable 2 ............................................ 138
SFR Definition 12.6. EIP2: Extended Interrupt Priority 2 ............................................ 139
SFR Definition 12.7. IT01CF: INT0/INT1 Configuration .............................................. 141
SFR Definition 13.1. PSCTL: Program Store R/W Control ......................................... 149
SFR Definition 13.2. FLKEY: Flash Lock and Key ...................................................... 150
SFR Definition 13.3. FLSCL: Flash Scale ................................................................... 151
SFR Definition 13.4. FLWR: Flash Write Only ............................................................ 151
SFR Definition 14.1. PMU0CF: Power Management Unit Configuration .................... 157
SFR Definition 14.2. PCON: Power Management Control Register ........................... 158
SFR Definition 15.1. CRC0CN: CRC0 Control ........................................................... 164
Rev. 1.3
13
Si1000/1/2/3/4/5
SFR Definition 15.2. CRC0IN: CRC0 Data Input ........................................................ 165
SFR Definition 15.3. CRC0DAT: CRC0 Data Output .................................................. 165
SFR Definition 15.4. CRC0AUTO: CRC0 Automatic Control ...................................... 166
SFR Definition 15.5. CRC0CNT: CRC0 Automatic Flash Sector Count ..................... 166
SFR Definition 15.6. CRC0FLIP: CRC0 Bit Flip .......................................................... 167
SFR Definition 16.1. DC0CN: DC-DC Converter Control ........................................... 174
SFR Definition 16.2. DC0CF: DC-DC Converter Configuration .................................. 175
SFR Definition 17.1. REG0CN: Voltage Regulator Control ........................................ 177
SFR Definition 18.1. VDM0CN: VDD_MCU Supply Monitor Control .......................... 182
SFR Definition 18.2. RSTSRC: Reset Source ............................................................ 184
SFR Definition 19.1. CLKSEL: Clock Select ............................................................... 190
SFR Definition 19.2. OSCICN: Internal Oscillator Control .......................................... 191
SFR Definition 19.3. OSCICL: Internal Oscillator Calibration ..................................... 191
SFR Definition 19.4. OSCXCN: External Oscillator Control ........................................ 192
SFR Definition 20.1. RTC0KEY: SmaRTClock Lock and Key .................................... 197
SFR Definition 20.2. RTC0ADR: SmaRTClock Address ............................................ 198
SFR Definition 20.3. RTC0DAT: SmaRTClock Data .................................................. 199
Internal Register Definition 20.4. RTC0CN: SmaRTClock Control ............................. 206
Internal Register Definition 20.5. RTC0XCN: 
SmaRTClock Oscillator Control ...................................... 207
Internal Register Definition 20.6. RTC0XCF: 
SmaRTClock Oscillator Configuration ............................ 208
Internal Register Definition 20.7. RTC0PIN: 
SmaRTClock Pin Configuration ...................................... 208
Internal Register Definition 20.8. CAPTUREn: 
SmaRTClock Timer Capture ........................................... 209
Internal Register Definition 20.9. ALARMn: SmaRTClock Alarm 
Programmed Value ......................................................... 209
SFR Definition 21.1. XBR0: Port I/O Crossbar Register 0 .......................................... 217
SFR Definition 21.2. XBR1: Port I/O Crossbar Register 1 .......................................... 218
SFR Definition 21.3. XBR2: Port I/O Crossbar Register 2 .......................................... 219
SFR Definition 21.4. P0MASK: Port0 Mask Register .................................................. 220
SFR Definition 21.5. P0MAT: Port0 Match Register ................................................... 220
SFR Definition 21.6. P1MASK: Port1 Mask Register .................................................. 221
SFR Definition 21.7. P1MAT: Port1 Match Register ................................................... 221
SFR Definition 21.8. P0: Port0 .................................................................................... 223
SFR Definition 21.9. P0SKIP: Port0 Skip .................................................................... 223
SFR Definition 21.10. P0MDIN: Port0 Input Mode ...................................................... 224
SFR Definition 21.11. P0MDOUT: Port0 Output Mode ............................................... 224
SFR Definition 21.12. P0DRV: Port0 Drive Strength .................................................. 225
SFR Definition 21.13. P1: Port1 .................................................................................. 226
SFR Definition 21.14. P1SKIP: Port1 Skip .................................................................. 226
SFR Definition 21.15. P1MDIN: Port1 Input Mode ...................................................... 227
SFR Definition 21.16. P1MDOUT: Port1 Output Mode ............................................... 227
SFR Definition 21.17. P1DRV: Port1 Drive Strength .................................................. 228
14
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 21.18. P2: Port2 .................................................................................. 228
SFR Definition 21.19. P2SKIP: Port2 Skip .................................................................. 229
SFR Definition 21.20. P2MDIN: Port2 Input Mode ...................................................... 229
SFR Definition 21.21. P2MDOUT: Port2 Output Mode ............................................... 230
SFR Definition 21.22. P2DRV: Port2 Drive Strength .................................................. 230
SFR Definition 22.1. SPI1CFG: SPI Configuration ..................................................... 237
SFR Definition 22.2. SPI1CN: SPI Control ................................................................. 238
SFR Definition 22.3. SPI1CKR: SPI Clock Rate ......................................................... 239
SFR Definition 22.4. SPI1DAT: SPI Data ................................................................... 240
SFR Definition 24.1. SMB0CF: SMBus Clock/Configuration ...................................... 297
SFR Definition 24.2. SMB0CN: SMBus Control .......................................................... 299
SFR Definition 24.3. SMB0ADR: SMBus Slave Address ............................................ 302
SFR Definition 24.4. SMB0ADM: SMBus Slave Address Mask .................................. 302
SFR Definition 24.5. SMB0DAT: SMBus Data ............................................................ 305
SFR Definition 25.1. SCON0: Serial Port 0 Control .................................................... 319
SFR Definition 25.2. SBUF0: Serial (UART0) Port Data Buffer .................................. 320
SFR Definition 26.7. SPI0CFG: SPI0 Configuration ................................................... 329
SFR Definition 26.8. SPI0CN: SPI0 Control ............................................................... 330
SFR Definition 26.9. SPI0CKR: SPI0 Clock Rate ....................................................... 331
SFR Definition 26.10. SPI0DAT: SPI0 Data ............................................................... 331
SFR Definition 27.1. CKCON: Clock Control .............................................................. 336
SFR Definition 27.2. TCON: Timer Control ................................................................. 341
SFR Definition 27.3. TMOD: Timer Mode ................................................................... 342
SFR Definition 27.4. TL0: Timer 0 Low Byte ............................................................... 343
SFR Definition 27.5. TL1: Timer 1 Low Byte ............................................................... 343
SFR Definition 27.6. TH0: Timer 0 High Byte ............................................................. 344
SFR Definition 27.7. TH1: Timer 1 High Byte ............................................................. 344
SFR Definition 27.8. TMR2CN: Timer 2 Control ......................................................... 348
SFR Definition 27.9. TMR2RLL: Timer 2 Reload Register Low Byte .......................... 349
SFR Definition 27.10. TMR2RLH: Timer 2 Reload Register High Byte ...................... 349
SFR Definition 27.11. TMR2L: Timer 2 Low Byte ....................................................... 350
SFR Definition 27.12. TMR2H Timer 2 High Byte ....................................................... 350
SFR Definition 27.13. TMR3CN: Timer 3 Control ....................................................... 354
SFR Definition 27.14. TMR3RLL: Timer 3 Reload Register Low Byte ........................ 355
SFR Definition 27.15. TMR3RLH: Timer 3 Reload Register High Byte ...................... 355
SFR Definition 27.16. TMR3L: Timer 3 Low Byte ....................................................... 356
SFR Definition 27.17. TMR3H Timer 3 High Byte ....................................................... 356
SFR Definition 28.1. PCA0CN: PCA Control .............................................................. 370
SFR Definition 28.2. PCA0MD: PCA Mode ................................................................ 371
SFR Definition 28.3. PCA0PWM: PCA PWM Configuration ....................................... 372
SFR Definition 28.4. PCA0CPMn: PCA Capture/Compare Mode .............................. 373
SFR Definition 28.5. PCA0L: PCA Counter/Timer Low Byte ...................................... 374
SFR Definition 28.6. PCA0H: PCA Counter/Timer High Byte ..................................... 374
SFR Definition 28.7. PCA0CPLn: PCA Capture Module Low Byte ............................. 375
SFR Definition 28.8. PCA0CPHn: PCA Capture Module High Byte ........................... 375
Rev. 1.3
15
Si1000/1/2/3/4/5
C2 Register Definition 30.1. C2ADD: C2 Address ...................................................... 377
C2 Register Definition 30.2. DEVICEID: C2 Device ID ............................................... 378
C2 Register Definition 30.3. REVID: C2 Revision ID .................................................. 378
C2 Register Definition 30.4. FPCTL: C2 Flash Programming Control ........................ 379
C2 Register Definition 30.5. FPDAT: C2 Flash Programming Data ............................ 379
16
Rev. 1.3
Si1000/1/2/3/4/5
1. System Overview
Si1000/1/2/3/4/5 devices are fully integrated mixed-signal system-on-a-chip MCUs. Highlighted features
are listed below. Refer to Table 2.1 for specific product feature selection and part ordering numbers.









240–960 MHz EZRadioPRO® transceiver
Single/Dual battery operation with on-chip dc-dc boost converter
High-speed pipelined 8051-compatible microcontroller core (up to 25 MIPS)
In-system, full-speed, non-intrusive debug interface (on-chip)
True 10-bit 300 ksps 23-channel single-ended ADC with analog multiplexer
6-bit programmable current reference
Precision programmable 24.5 MHz internal oscillator with spread spectrum technology
64 kB or 32 kB of on-chip flash memory
4352 bytes of on-chip RAM
SMBus/I2C, Enhanced UART, and two Enhanced SPI serial interfaces implemented in hardware 
(SPI1 is dedicated for communication with the EZRadioPRO peripheral)
 Four general-purpose 16-bit timers
 Programmable counter/timer array (PCA) with six capture/compare modules and watchdog timer
(WDT) function
 On-chip power-on reset, VDD monitor, and temperature sensor

Two on-chip voltage comparators with 18 touch sense inputs
 19 or 22 port I/O (5 V tolerant except for GPIO_0, GPIO_1, and GPIO_2)
With on-chip power-on reset, VDD monitor, watchdog timer, and clock oscillator, the Si1000/1/2/3/4/5
devices are truly standalone system-on-a-chip solutions. The flash memory can be reprogrammed even incircuit, providing non-volatile data storage, and also allowing field upgrades of the 8051 firmware. User
software has complete control of all peripherals, and may individually shut down any or all peripherals for
power savings.

The on-chip Silicon Labs 2-Wire (C2) Development Interface allows non-intrusive (uses no on-chip
resources), full speed, in-circuit debugging using the production MCU installed in the final application. This
debug logic supports inspection and modification of memory and registers, setting breakpoints, single
stepping, and run and halt commands. All analog and digital peripherals are fully functional while debugging using C2. The two C2 interface pins can be shared with user functions, allowing in-system debugging
without occupying package pins.
Each device is specified for 1.8 to 3.6 V operation over the industrial temperature range (–40 to +85 °C).
The Port I/O and RST pins are tolerant of input signals up to 5 V. The Si1000/1/2/3/4/5 are available in a
42-pin LGA package (lead-free and RoHS compliant). See Table 2.1 for ordering information. Block diagrams are included in Figure 1.1 through Figure 1.6.
The transceiver's extremely low receive sensitivity (–121 dBm) coupled with industry leading +20 dBm output power ensures extended range and improved link performance. Built-in antenna diversity and support
for frequency hopping can be used to further extend range and enhance performance. The advanced radio
features including continuous frequency coverage from 240–960 MHz in 156 Hz or 312 Hz steps allow precise tuning control. Additional system features such as an automatic wake-up timer, low battery detector,
64 byte TX/RX FIFOs, automatic packet handling, and preamble detection reduce overall current consumption. The transceivers digital receive architecture features a high-performance ADC and DSP-based
modem which performs demodulation, filtering, and packet handling for increased flexibility and performance. The direct digital transmit modulation and automatic PA power ramping ensure precise transmit
modulation and reduced spectral spreading, ensuring compliance with global regulations including FCC,
ETSI, ARIB, and 802.15.4d regulations.
An easy-to-use calculator is provided to quickly configure the radio settings, simplifying customer's system
design and reducing time to market.
Rev. 1.3
17
Si1000/1/2/3/4/5
Power On
Reset/PMU
Wake
Reset
C2CK/RST
Debug /
Programming
Hardware
CIP-51 8051
Controller Core
Analog Peripherals
64k Byte ISP Flash
Program Memory
6-bit
IREF
256 Byte SRAM
C2D
VREF
VREF
CP0, CP0A
CP1, CP1A
P0.3/XTAL2
XTAL3
XTAL4
AGC
RXp
RXn
LNA
Mixer
PGA
ADC
+
-
+
-
Comparators
Digital Peripherals
Low Power
20 MHz
Oscillator
P0.2/XTAL1
VDD
VREF
Temp
Sensor
GND
SFR
Bus
Precision
24.5 MHz
Oscillator
TX
A
M
U
X
10-bit
300ksps
ADC
SYSCLK
GND
PA
External
CRC
Engine
VREG
VDD
IREF0
Internal
4096 Byte XRAM
RF XCVR
(240-960 MHz,
+20 dBm)
Transceiver Control Interface
Digital
Modem
Delta
Sigma
Modulator
Digital
Logic
UART
External
Oscillator
Circuit
Timers 0,
1, 2, 3
SmaRTClock
Oscillator
PCA/
WDT
SMBus
System Clock
Configuration
XIN
XOUT
OSC
Priority
Crossbar
Decoder
Port I/O
Config
SPI 0
22
ANALOG &
DIGITAL I/O
Figure 1.1. Si1000 Block Diagram
Power On
Reset/PMU
Wake
Reset
C2CK/RST
Debug /
Programming
Hardware
CIP-51 8051
Controller Core
Analog Peripherals
32k Byte ISP Flash
Program Memory
6-bit
IREF
256 Byte SRAM
C2D
VDD
VREF
VREF
Precision
24.5 MHz
Oscillator
P0.2/XTAL1
XTAL3
XTAL4
CP1, CP1A
SFR
Bus
+
-
RXp
RXn
LNA
PGA
ADC
+
-
Digital Peripherals
Transceiver Control Interface
Digital
Modem
Delta
Sigma
Modulator
Digital
Logic
UART
Timers 0,
1, 2, 3
SmaRTClock
Oscillator
PCA/
WDT
SMBus
SPI 0
Rev. 1.3
XIN
XOUT
OSC
Priority
Crossbar
Decoder
Figure 1.2. Si1001 Block Diagram
18
AGC
Mixer
Comparators
External
Oscillator
Circuit
System Clock
Configuration
VDD
VREF
Temp
Sensor
GND
CP0, CP0A
Low Power
20 MHz
Oscillator
P0.3/XTAL2
TX
A
M
U
X
10-bit
300ksps
ADC
SYSCLK
GND
PA
External
CRC
Engine
VREG
IREF0
Internal
4096 Byte XRAM
RF XCVR
(240-960 MHz,
+20 dBm)
Port I/O
Config
22
ANALOG &
DIGITAL I/O
Si1000/1/2/3/4/5
Power On
Reset/PMU
Wake
Reset
C2CK/RST
Debug /
Programming
Hardware
CIP-51 8051
Controller Core
Analog Peripherals
64k Byte ISP Flash
Program Memory
6-bit
IREF
256 Byte SRAM
C2D
VDD
VREF
VREF
CP0, CP0A
CP1, CP1A
P0.3/XTAL2
XTAL3
XTAL4
AGC
RXp
RXn
LNA
Mixer
PGA
ADC
+
-
+
-
Comparators
Digital Peripherals
Low Power
20 MHz
Oscillator
P0.2/XTAL1
VDD
VREF
Temp
Sensor
GND
SFR
Bus
Precision
24.5 MHz
Oscillator
TX
A
M
U
X
10-bit
300ksps
ADC
SYSCLK
GND
PA
External
CRC
Engine
VREG
IREF0
Internal
4096 Byte XRAM
RF XCVR
(240-960 MHz,
+13 dBm)
Transceiver Control Interface
Digital
Modem
Delta
Sigma
Modulator
Digital
Logic
UART
External
Oscillator
Circuit
Timers 0,
1, 2, 3
SmaRTClock
Oscillator
PCA/
WDT
SMBus
System Clock
Configuration
XIN
XOUT
OSC
Priority
Crossbar
Decoder
Port I/O
Config
SPI 0
22
ANALOG &
DIGITAL I/O
Figure 1.3. Si1002 Block Diagram
Power On
Reset/PMU
Wake
Reset
C2CK/RST
Debug /
Programming
Hardware
CIP-51 8051
Controller Core
Analog Peripherals
32k Byte ISP Flash
Program Memory
6-bit
IREF
256 Byte SRAM
C2D
VDD
VREF
VREF
Precision
24.5 MHz
Oscillator
P0.3/XTAL2
XTAL3
XTAL4
CP1, CP1A
SFR
Bus
AGC
RXp
RXn
LNA
Mixer
+
-
PGA
ADC
+
-
Comparators
Digital Peripherals
Transceiver Control Interface
Digital
Modem
Delta
Sigma
Modulator
Digital
Logic
UART
External
Oscillator
Circuit
Timers 0,
1, 2, 3
SmaRTClock
Oscillator
PCA/
WDT
System Clock
Configuration
VDD
VREF
Temp
Sensor
GND
CP0, CP0A
Low Power
20 MHz
Oscillator
P0.2/XTAL1
TX
A
M
U
X
10-bit
300ksps
ADC
SYSCLK
GND
PA
External
CRC
Engine
VREG
IREF0
Internal
4096 Byte XRAM
RF XCVR
(240-960 MHz,
+13 dBm)
XIN
XOUT
OSC
Priority
Crossbar
Decoder
SMBus
SPI 0
Port I/O
Config
22
ANALOG &
DIGITAL I/O
Figure 1.4. Si1003 Block Diagram
Rev. 1.3
19
Si1000/1/2/3/4/5
Power On
Reset/PMU
Wake
Reset
C2CK/RST
CIP-51 8051
Controller Core
Analog Peripherals
64k Byte ISP Flash
Program Memory
6-bit
IREF
256 Byte SRAM
Debug /
Programming
Hardware
VDD/DC+
VREG
Analog
Power
GND/DC-
VBAT
DC/DC
Converter
VREF
VREF
CP0, CP0A
CP1, CP1A
SFR
Bus
XTAL3
XTAL4
AGC
RXp
RXn
LNA
Mixer
PGA
ADC
+
-
+
-
Comparators
Digital Peripherals
Transceiver Control Interface
Digital
Modem
Delta
Sigma
Modulator
Digital
Logic
UART
External
Oscillator
Circuit
Timers 0,
1, 2, 3
SmaRTClock
Oscillator
PCA/
WDT
XTAL1
XTAL2
VDD
VREF
Temp
Sensor
GND
Low Power
20 MHz
Oscillator
GND
TX
A
M
U
X
10-bit
300ksps
ADC
SYSCLK
Precision
24.5 MHz
Oscillator
PA
External
CRC
Engine
Digital
Power
IREF0
Internal
4096 Byte XRAM
C2D
Power Net
RF XCVR
(240-960 MHz)
SMBus
System Clock
Configuration
XIN
XOUT
OSC
Priority
Crossbar
Decoder
Port I/O
Config
SPI 0
19
ANALOG &
DIGITAL I/O
Figure 1.5. Si1004 Block Diagram
Power On
Reset/PMU
Wake
Reset
C2CK/RST
CIP-51 8051
Controller Core
Analog Peripherals
32k Byte ISP Flash
Program Memory
6-bit
IREF
256 Byte SRAM
Debug /
Programming
Hardware
VDD/DC+
Analog
Power
GND/DC-
VBAT
DC/DC
Converter
XTAL1
XTAL2
XTAL4
Digital
Power
PA
External
VREF
VREF
TX
A
M
U
X
10-bit
300ksps
ADC
CRC
Engine
VDD
VREF
Temp
Sensor
CP1, CP1A
SFR
Bus
+
-
Comparators
Transceiver Control Interface
PGA
ADC
Digital
Modem
Delta
Sigma
Modulator
Digital
Logic
UART
External
Oscillator
Circuit
Timers 0,
1, 2, 3
SmaRTClock
Oscillator
PCA/
WDT
SPI 0
Figure 1.6. Si1005 Block Diagram
Rev. 1.3
XIN
XOUT
OSC
Priority
Crossbar
Decoder
SMBus
System Clock
Configuration
20
RXp
RXn
LNA
+
-
Digital Peripherals
Low Power
20 MHz
Oscillator
AGC
Mixer
GND
CP0, CP0A
SYSCLK
Precision
24.5 MHz
Oscillator
GND
XTAL3
VREG
IREF0
Internal
4096 Byte XRAM
C2D
Power Net
RF XCVR
(240-960 MHz)
Port I/O
Config
19
ANALOG &
DIGITAL I/O
Si1000/1/2/3/4/5
1.1. Typical Connection Diagram
The application shown in Figure 1.7 is designed for a system with a TX/RX direct-tie configuration without
the use of a TX/RX switch. Most lower power applications will use this configuration. A complete direct-tie
reference design is available from Silicon Laboratories applications support.
For applications seeking improved performance in the presence of multipath fading, antenna diversity can
be used. Antenna diversity support is integrated into the EZRadioPRO transceiver and can improve the
system link budget by 8–10 dB in the presence of these fading conditions, resulting in substantial range
increases. A complete Antenna Diversity reference design is available from Silicon Laboratories applications support.
supply voltage
100p
100n
1u
X1
30MHz
L1
L2
L4
C3
XIN
nIRQ
C8
XOUT
C7
SDN
C6
VDD_MCU
VDD_DIG
Px.x
VDD_RF
TX
L3
C1
RFp
C2
Si100x
RXn
GPIO2
0.1 uF
VR_DIG
GPIO1
L5
L6
GPIO0
ANT_A
C4
0.1 uF
C9
1u
C5
Programmable load capacitors for X1 are integrated.
L1-L6 and C1-C5 values depend on frequency band, antenna
impedance, output power and supply voltage range.
Figure 1.7. Si1002/3 RX/TX Direct-tie Application Example
Supply Voltage
100 n
1u
L3
L2
5
3
4
C2
C1
RXp
Si100x
RXn
C4
L4
GPIO2
2
C3
VDD_MCU
VDD_DIG
Px.x
0.1 uF
VR_DIG
6
VDD_RF
TX
GPIO1
1
L1
GPIO0
TR & ANT-DIV
Switch
nIRQ
100 p
X1
30 MHz
XOUT
C8
XIN
C7
SDN
C6
0.1 uF
C9
C5
1u
Programmable load capacitors for X1 are
integrated.
L1–L4 and C1–C5 values depend on frequency
band, antenna impedance, output power, and
supply voltage range.
Figure 1.8. Si1000/1 Antenna Diversity Application Example
Rev. 1.3
21
Si1000/1/2/3/4/5
1.2. CIP-51™ Microcontroller Core
1.2.1. Fully 8051 Compatible
The Si1000/1/2/3/4/5 family utilizes Silicon Labs' proprietary CIP-51 microcontroller core. The CIP-51 is
fully compatible with the MCS-51™ instruction set; standard 803x/805x assemblers and compilers can be
used to develop software. The CIP-51 core offers all the peripherals included with a standard 8052.
1.2.2. Improved Throughput
The CIP-51 employs a pipelined architecture that greatly increases its instruction throughput over the standard 8051 architecture. In a standard 8051, all instructions except for MUL and DIV take 12 or 24 system
clock cycles to execute with a maximum system clock of 12-to-24 MHz. By contrast, the CIP-51 core executes 70% of its instructions in one or two system clock cycles, with only four instructions taking more than
four system clock cycles.
The CIP-51 has a total of 109 instructions. The table below shows the total number of instructions that
require each execution time.
Clocks to Execute
1
2
2/3
3
3/4
4
4/5
5
8
Number of Instructions
26
50
5
14
7
3
1
2
1
With the CIP-51's maximum system clock at 25 MHz, it has a peak throughput of 25 MIPS.
1.2.3. Additional Features
The Si1000/1/2/3/4/5 SoC family includes several key enhancements to the CIP-51 core and peripherals to
improve performance and ease of use in end applications.
The extended interrupt handler provides multiple interrupt sources into the CIP-51, allowing numerous
analog and digital peripherals to interrupt the controller. An interrupt driven system requires less intervention by the MCU, giving it more effective throughput. The extra interrupt sources are very useful when
building multi-tasking, real-time systems.
Eight reset sources are available: power-on reset circuitry (POR), an on-chip VDD monitor (forces reset
when power supply voltage drops below safe levels), a watchdog timer, a Missing Clock Detector, SmaRTClock oscillator fail or alarm, a voltage level detection from Comparator0, a forced software reset, an external reset pin, and an illegal flash access protection circuit. Each reset source except for the POR, Reset
Input Pin, or flash error may be disabled by the user in software. The WDT may be permanently disabled in
software after a power-on reset during MCU initialization.
The internal oscillator factory is calibrated to 24.5 MHz and is accurate to ±2% over the full temperature
and supply range. The internal oscillator period can also be adjusted by user firmware. An additional
20 MHz low power oscillator is also available which facilitates low-power operation. An external oscillator
drive circuit is included, allowing an external crystal, ceramic resonator, capacitor, RC, or CMOS clock
source to generate the system clock. If desired, the system clock source may be switched between both
internal and external oscillator circuits. An external oscillator can also be extremely useful in low power
applications, allowing the MCU to run from a slow (power saving) source, while periodically switching to
the fast (up to 25 MHz) internal oscillator as needed.
22
Rev. 1.3
Si1000/1/2/3/4/5
1.3. Port Input/Output
Digital and analog resources are available through 19 (Si1000/1/2/3) or 16 (Si1004/5) I/O pins. Three additional GPIO pins are available through the EZRadioPRO peripheral. Port pins are organized as three bytewide ports. Port pins P0.0–P2.6 can be defined as digital or analog I/O. Digital I/O pins can be assigned to
one of the internal digital resources or used as general purpose I/O (GPIO). Analog I/O pins are used by
the internal analog resources. P1.0, P1.1, P1.2, and P1.4 are dedicated for communication with the EZRadioPRO peripheral. P1.3 is not available. P2.7 can be used as GPIO and is shared with the C2 Interface
Data signal (C2D). See Section “29. Device Specific Behavior” on page 376 for more details.
The designer has complete control over which digital and analog functions are assigned to individual port
pins and is limited only by the number of physical I/O pins. This resource assignment flexibility is achieved
through the use of a Priority Crossbar Decoder. See Section “21.3. Priority Crossbar Decoder” on
page 214 for more information on the crossbar.
All Px.x Port I/Os are 5 V tolerant when used as digital inputs or open-drain outputs. For Port I/Os configured as push-pull outputs, current is sourced from the VDD_MCU supply. Port I/Os used for analog functions can operate up to the VDD_MCU supply voltage. See Section “21.1. Port I/O Modes of Operation” on
page 211 for more information on Port I/O operating modes and the electrical specifications chapter for
detailed electrical specifications.
XBR0, XBR1,
XBR2, PnSKIP
Registers
Port Match
P0MASK, P0MAT
P1MASK, P1MAT
External Interrupts
EX0 and EX1
Priority
Decoder
Highest
Priority
UART
4
(Internal Digital Signals)
SPI0
SPI1
SMBus
CP0
CP1
Outputs
P0.0
2
Digital
Crossbar
8
4
8
7
T0, T1
P0
I/O
Cells
P0.7
SYSCLK
PCA
Lowest
Priority
PnMDOUT,
PnMDIN Registers
2
P1.5
P1
I/O
Cells
P1.7
2
8
(Port Latches)
P0
8
(P0.0-P0.7)
8
P1
(P1.0-P1.7)
8
P2
(P2.0-P2.7)
P1.6
P2.0
P2
I/O
Cell
P2.6
P2.7
To Analog Peripherals
(ADC0, CP0, and CP1 inputs,
VREF, IREF0, AGND)
No analog functionality
available on P2.7
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the
EZRadioPRO peripheral. P1.3 is not internally or externally connected.
P2.4, P2.5, and P2.6 are only available on Si1000/1/2/3
Figure 1.9. Port I/O Functional Block Diagram
Rev. 1.3
23
Si1000/1/2/3/4/5
1.4. Serial Ports
The Si1000/1/2/3/4/5 family includes an SMBus/I2C interface, a full-duplex UART with enhanced baud rate
configuration, and an Enhanced SPI interface. Each of the serial buses is fully implemented in hardware
and makes extensive use of the CIP-51's interrupts, thus requiring very little CPU intervention. There is
also a dedicated EZRadioPRO Serial Interface (SPI1) to allow communication with the EZRadioPRO
peripheral.
1.5. Programmable Counter Array
An on-chip Programmable Counter/Timer Array (PCA) is included in addition to the four 16-bit general purpose counter/timers. The PCA consists of a dedicated 16-bit counter/timer time base with six programmable capture/compare modules. The PCA clock is derived from one of six sources: the system clock divided
by 12, the system clock divided by 4, Timer 0 overflows, an External Clock Input (ECI), the system clock, or
the external oscillator clock source divided by 8.
Each capture/compare module can be configured to operate in a variety of modes: edge-triggered capture,
software timer, high-speed output, pulse width modulator (8, 9, 10, 11, or 16-bit), or frequency output. Additionally, Capture/Compare Module 5 offers watchdog timer capabilities. Following a system reset, Module 5
is configured and enabled in WDT mode. The PCA Capture/Compare Module I/O and External Clock Input
may be routed to Port I/O via the Digital Crossbar.
SYSCLK /12
SYSCLK /4
Timer 0 Overflow
ECI
PCA
CLOCK
MUX
16 -Bit Counter/Timer
SYSCLK
External Clock /8
Capture/ Compare
Module 0
Capture/ Compare
Module 1
Capture/ Compare
Module 2
Capture/ Compare
Module 3
Figure 1.10. PCA Block Diagram
24
Rev. 1.3
Capture/ Compare
Module5 / WDT
CEX5
Port I/O
CEX4
CEX3
CEX2
CEX1
CEX0
ECI
Crossbar
Capture/ Compare
Module 4
Si1000/1/2/3/4/5
1.6. 10-bit SAR ADC with 16-bit Auto-Averaging Accumulator and Autonomous
Low Power Burst Mode
Si1000/1/2/3/4/5 devices have a 300 ksps, 10-bit successive-approximation-register (SAR) ADC with integrated track-and-hold and programmable window detector. ADC0 also has an autonomous low power
Burst Mode which can automatically enable ADC0, capture and accumulate samples, then place ADC0 in
a low power shutdown mode without CPU intervention. It also has a 16-bit accumulator that can automatically average the ADC results, providing an effective 11, 12, or 13-bit ADC result without any additional
CPU intervention.
The ADC can sample the voltage at any of the GPIO pins (with the exception of P2.7) and has an on-chip
attenuator that allows it to measure voltages up to twice the voltage reference. Additional ADC inputs
include an on-chip temperature sensor, the VDD_MCU supply voltage, the VBAT supply voltage, and the
internal digital supply voltage.
VDD
ADC
AD0CM1
AD0CM2
AD0CM0
010
011
100
Timer 2 Overflow
Timer 3 Overflow
CNVSTR Input
REF
16-Bit Accumulator
SYSCLK
AD0TM
AMP0GN
AD08BE
AD0SC0
AD0SC1
ADC0CF
AD0BUSY (W)
Timer 0 Overflow
ADC0LTH
ADC0H
AIN+
000
001
ADC0L
10-bit
SAR
AD0SC2
From
AMUX0
Start
Conversion
Burst Mode Logic
AD0SC3
ADC0PWR
AD0SC4
ADC0TK
AD0WINT
AD0INT
AD0BUSY
BURSTEN
AD0EN
ADC0CN
AD0WINT
ADC0LTL
32
Window
Compare
Logic
ADC0GTH ADC0GTL
Figure 1.11. ADC0 Functional Block Diagram
Rev. 1.3
25
Si1000/1/2/3/4/5
AD0MX4
AD0MX3
AD0MX2
AD0MX1
AM0MX0
ADC0MX
P0.0
Programmable
Attenuator
AIN+
P2.6*
AMUX
Temp
Sensor
ADC0
Gain = 0. 5 or 1
Digital Supply
VDD_MCU
*P1.0 – P1.4 are not
available as device pins
Figure 1.12. ADC0 Multiplexer Block Diagram
1.7. Programmable Current Reference (IREF0)
Si1000/1/2/3/4/5 devices include an on-chip programmable current reference (source or sink) with two output current settings: low power mode and high current mode. The maximum current output in low power
mode is 63 µA (1 µA steps) and the maximum current output in high current mode is 504 µA (8 µA steps).
1.8. Comparators
Si1000/1/2/3/4/5 devices include two on-chip programmable voltage comparators: Comparator 0 (CPT0),
which is shown in Figure 1.13, and Comparator 1 (CPT1), which is shown in Figure 1.14. The two comparators operate identically but may differ in their ability to be used as reset or wake-up sources. See Section
“18. Reset Sources” on page 178 and Section “14. Power Management” on page 152 for details on reset
sources and low power mode wake-up sources, respectively.
The comparators offer programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a synchronous “latched” output (CP0, CP1), or an
asynchronous “raw” output (CP0A, CP1A). The asynchronous CP0A signal is available even when the
system clock is not active. This allows the comparator to operate and generate an output when the device
is in some low power modes.
The comparator inputs may be connected to Port I/O pins or to other internal signals. Port pins may also be
used to directly sense capacitive touch switches. See Application Note “AN338: Capacitive Touch Sense
Solution” for details on Capacitive Touch Switch sensing.
26
Rev. 1.3
CPT0CN
Si1000/1/2/3/4/5
CP0EN
CP0OUT
CP0RIF
CP0FIF
VDD
CP0HYP1
CP0HYP0
CP0HYN1
CP0
Interrupt
CP0HYN0
CPT0MD
Analog Input Multiplexer
CP0FIE
CP0RIE
CP0MD1
CP0MD0
Px.x
CP0
Rising-edge
CP0 +
CP0
Falling-edge
Interrupt
Logic
Px.x
CP0
+
SET
D
-
CLR
D
Q
Q
SET
CLR
Q
Q
Px.x
Crossbar
(SYNCHRONIZER)
GND
CP0 -
CP0A
(ASYNCHRONOUS)
Reset
Decision
Tree
Px.x
Figure 1.13. Comparator 0 Functional Block Diagram
CPT0CN
CP1EN
CP1OUT
CP1RIF
VDD
CP1FIF
CP1HYP1
CP1
Interrupt
CP1HYP0
CP1HYN1
CP1HYN0
CPT0MD
Analog Input Multiplexer
CP1FIE
CP1RIE
CP1MD1
CP1MD0
Px.x
CP1
Rising-edge
CP1 +
CP1
Falling-edge
Interrupt
Logic
Px.x
CP1
+
D
-
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Px.x
Crossbar
(SYNCHRONIZER)
CP1 -
GND
(ASYNCHRONOUS)
CP1A
Reset
Decision
Tree
Px.x
Figure 1.14. Comparator 1 Functional Block Diagram
Rev. 1.3
27
Si1000/1/2/3/4/5
2. Ordering Information
Package
Lead-free (RoHS Compliant)
Minimum Operating Voltage (Volts)
Maximum Transmit Power
Temperature Sensor
Internal Voltage Reference
10-bit 300ksps ADC
Digital Port I/Os (includes EZRadioPRO GPIOs)
Programmable Counter Array
Timers (16-bit)
Enhanced SPI (available for external communication)
UART
SMBus/I2C
SmaRTClock Real Time Clock
RAM (bytes)
Flash Memory (kB)
MIPS (Peak)
Ordering Part Number
Table 2.1. Product Selection Guide
Si1000-E-GM2 25 64 4352
P
1
1
1
4
P
22 P
P
P
+20 dBm 1.8 P
LGA-42
Si1001-E-GM2 25 32 4352
P
1
1
1
4
P
22 P
P
P
+20 dBm 1.8 P
LGA-42
Si1002-E-GM2 25 64 4352
P
1
1
1
4
P
22 P
P
P
+13 dBm 1.8 P
LGA-42
Si1003-E-GM2 25 32 4352
P
1
1
1
4
P
22 P
P
P
+13 dBm 1.8 P
LGA-42
Si1004-E-GM2 25 64 4352
P
1
1
1
4
P
19 P
P
P
+13 dBm 0.9 P
LGA-42
Si1005-E-GM2 25 32 4352
P
1
1
1
4
P
19 P
P
P
+13 dBm 0.9 P
LGA-42
28
Rev. 1.3
Si1000/1/2/3/4/5
3. Pinout and Package Definitions
Table 3.1. Pin Definitions for the Si1000/1/2/3/4/5
Name
Pin Number
Type
Description
Si1000/1
Si1004/5
Si1002/3
VDD_MCU
38
—
P In
GND_MCU
37
—
G
VBAT
—
41
P In
Battery Supply Voltage. Must be 0.9 to 1.8 V in single-cell
battery mode and 1.8 to 3.6 V in dual-cell battery mode.
GND
—
38
P In
In dual-cell battery mode, this pin must be connected
directly to ground.
In one-cell applications, this pin should be connected
directly to the negative battery terminal, which is not
connected to the ground plane.
VBAT-
DCEN
G
—
40
P In
G
VDD_MCU /
—
39
DC+
GND_MCU
P In
P Out
—
37
DC–
G
G
Power Supply Voltage for the entire MCU except for the
EZRadioPRO peripheral. Must be 1.8 to 3.6 V.
Required Ground for the entire MCU except for the 
EZRadioPRO peripheral.
DC-DC Enable Pin. In single-cell battery mode, this pin
must be connected to VBAT through a 0.68 µH inductor.
In dual-cell battery mode, this pin must be connected
directly to ground.
Power Supply Voltage for the entire MCU except for the
EZRadioPRO peripheral. Must be 1.8 to 3.6 V. This supply
voltage is not required in low power sleep mode. This
voltage must always be > VBAT.
Positive output of the dc-dc converter. In single-cell battery
mode, a 1uF ceramic capacitor is required between dc+ and
dc–. This pin can supply power to external devices when
operating in single-cell battery mode.
In dual-cell battery mode, this pin must be connected
directly to ground.
DC-DC converter return current path. In one-cell mode, this
pin must be connected to the ground plane.
VDD_RF
16
16
P In
Power Supply Voltage for the analog portion of the 
EZRadioPRO peripheral. Must be 1.8 to 3.6 V.
VDD_DIG
28
28
P In
Power Supply Voltage for the digital portion of the 
EZRadioPRO peripheral. Must be 1.8 to 3.6 V.
VR_DIG
27
27
P Out
GND_RF
23
23
G
Regulated Output Voltage of the digital 1.7 V regulator for
the EZRadioPRO peripheral. A 1 µF decoupling capacitor is
required.
Required Ground for the digital and analog portions of the
EZRadioPRO peripheral.
Rev. 1.3
29
Si1000/1/2/3/4/5
Table 3.1. Pin Definitions for the Si1000/1/2/3/4/5 (Continued)
Name
Pin Number
Type
Description
Si1000/1
Si1004/5
Si1002/3
RST/
39
42
C2CK
P2.7/
40
1
C2D
D I/O
Device Reset. Open-drain output of internal POR or VDD
monitor. An external source can initiate a system reset by
driving this pin low for at least 15 µs. A 1–5 k pullup to
VDD_MCU is recommended. See Reset Sources section
for a complete description.
D I/O
Clock signal for the C2 Debug Interface.
D I/O
Port 2.7. This pin can only be used as GPIO. The Crossbar
cannot route signals to this pin and it cannot be configured
as an analog input. See Port I/O section for a complete
description.
D I/O
Bi-directional data signal for the C2 Debug Interface.
XTAL3
1
3
A In
SmaRTClock Oscillator Crystal Input.
See Section 20 for a complete description.
XTAL4
42
2
A Out
SmaRTClock Oscillator Crystal Output.
See Section 20 for a complete description.
P0.0
36
36
A In
A Out
VREF
P0.1
35
35
34
34
P0.3
XTAL2
33
33
External Clock Input. This pin is the external oscillator
return for a crystal or resonator. See Oscillator section.
D I/O or Port 0.3. See Port I/O Section for a complete description.
A In
A Out
D In
A In
30
Optional Analog Ground. See VREF chapter.
D I/O or Port 0.2. See Port I/O Section for a complete description.
A In
A In
XTAL1
External VREF Input.
Internal VREF Output. External VREF decoupling capacitors
are recommended. See Voltage Reference section.
D I/O or Port 0.1. See Port I/O Section for a complete description.
A In
G
AGND
P0.2
D I/O or Port 0.0. See Port I/O section for a complete description.
A In
External Clock Output. This pin is the excitation driver for an
external crystal or resonator.
External Clock Input. This pin is the external clock input in
external CMOS clock mode.
External Clock Input. This pin is the external clock input in
capacitor or RC oscillator configurations.
See Oscillator section for complete details.
Rev. 1.3
Si1000/1/2/3/4/5
Table 3.1. Pin Definitions for the Si1000/1/2/3/4/5 (Continued)
Name
Pin Number
Type
Description
Si1000/1
Si1004/5
Si1002/3
P0.4
32
32
D Out
TX
P0.5
31
31
30
30
P0.7
UART RX Pin. See Port I/O section.
D I/O or Port 0.6. See Port I/O section for a complete description.
A In
D In
CNVSTR
UART TX Pin. See Port I/O section.
D I/O or Port 0.5. See Port I/O section for a complete description.
A In
D In
RX
P0.6
D I/O or Port 0.4. See Port I/O section for a complete description.
A In
External Convert Start Input for ADC0. See ADC0 section
for a complete description.
29
29
D I/O or Port 0.7. See Port I/O section for a complete description.
A In
A Out IREF0 Output. See IREF section for complete description.
P1.5
10
10
D I/O or Port 1.5. See Port I/O section for a complete description.
A In
P1.6
9
9
D I/O or Port 1.6. See Port I/O section for a complete description.
A In
P1.7
8
8
D I/O or Port 1.7. See Port I/O section for a complete description.
A In
P2.0
7
7
D I/O or Port 2.0. See Port I/O section for a complete description.
A In
P2.1
6
6
D I/O or Port 2.1. See Port I/O section for a complete description.
A In
P2.2
5
5
D I/O or Port 2.2. See Port I/O section for a complete description.
A In
P2.3
4
4
D I/O or Port 2.3. See Port I/O section for a complete description.
A In
P2.4
3
—
D I/O or Port 2.4. See Port I/O section for a complete description.
A In
P2.5
2
—
D I/O or Port 2.5. See Port I/O section for a complete description.
A In
P2.6
41
—
D I/O or Port 2.6. See Port I/O section for a complete description.
A In
IREF0
Rev. 1.3
31
Si1000/1/2/3/4/5
Table 3.1. Pin Definitions for the Si1000/1/2/3/4/5 (Continued)
Name
Pin Number
Type
Description
Si1000/1
Si1004/5
Si1002/3
32
GPIO_0
24
24
D I/O or General Purpose I/O controlled by the EZRadioPRO periphA I/O eral. May be configured through the EZRadioPRO registers
D I/O or to perform various functions including: Clock Output, FIFO
status, POR, Wake-Up Timer, Low Battery Detect, TRSW,
A I/O
AntDiversity control, etc. See the EZRadioPRO GPIO ConD I/O or figuration Registers for more information.
A I/O
GPIO_1
25
25
GPIO_2
26
26
nIRQ
11
11
DO
EZRadioPRO peripheral interrupt status pin. Will be set low
to indicate a pending EZRadioPRO interrupt event. See the
EZRadioPRO Control Logic Registers for more details. This
pin is an open-drain output with a 220 k internal pullup
resistor. An external pull-up resistor is recommended.
XOUT
12
12
AO
EZRadioPRO peripheral crystal oscillator output. Connect
to an external 30 MHz crystal or to an external clock source.
If using an external clock source with no crystal, dc coupling
with a nominal 0.8 VDC level is recommended with a minimum ac amplitude of 700 mVpp. Refer to AN417 for more
details about using an external clock source.
XIN
13
13
AI
EZRadioPRO peripheral crystal oscillator input. Connect to
an external 30 MHz crystal or leave floating if driving the
XOUT pin with an external signal source.
NC
14, 20,
22
14, 20,
22
SDN
15
15
DI
EZRadioPRO peripheral shutdown pin. When driven to
logic HIGH, the EZRadioPRO peripheral will be completely
shut down and the contents of the EZRadioPRO registers
will be lost. This pin should be driven to logic LOW during all
other times; this pin should never be left floating.
TX
17
17
AO
EZRadioPRO peripheral transmit RF output pin. The PA
output is an open-drain connection so the L-C match must
supply (1.8 to 3.6 VDC) to this pin.
RXp
18
18
AI
RXn
19
19
AI
EZRadioPRO peripheral differential RF input pins of the
LNA. See application schematic for example matching network.
ANT_A
21
21
DO
EZRadioPRO peripheral TR switch control signal.
No Connect. May be left floating or tied to power or ground.
Rev. 1.3
XTAL4
P2.6
P2.7/C2D
RST/C2CK
VDD_MCU
GND_MCU
P0.0/VREF
42
41
40
39
38
37
36
Si1000/1/2/3/4/5
XTAL3
1
35
P0.1/AGND
P2.5
2
34
P0.2/XTAL1
P2.4
3
33
P0.3/XTAL2
P2.3
4
32
P0.4/TX
P2.2
5
31
P0.5/RX
P2.1
6
30
P0.6/CNVSTR
P2.0
7
29
P0.7/IREF0
P1.7
8
28
VDD_DIG
P1.6
9
27
VR_DIG
P1.5
10
26
GPIO_2
nIRQ
11
25
GPIO_1
XOUT
12
24
GPIO_0
XIN
13
23
GND_RF
N.C.
14
22
N.C.
Si1000/1/2/3
Top View
15
16
17
18
19
20
21
SDN
VDD_RF
TX
RXp
RXn
N.C.
ANT_A
GND
Figure 3.1. Si100/1/2/3-E-GM2 Pinout Diagram (Top View)
Rev. 1.3
33
RST/C2CK
VBAT
DCEN
VDD_MCU/DC+
GND/VBAT-
GND_MCU/DC-
P0.0/VREF
42
41
40
39
38
37
36
Si1000/1/2/3/4/5
P2.7/C2D
1
35
P0.1/AGND
XTAL4
2
34
P0.2/XTAL1
XTAL3
3
33
P0.3/XTAL2
P2.3
4
32
P0.4/TX
P2.2
5
31
P0.5/RX
P2.1
6
30
P0.6/CNVSTR
P2.0
7
29
P0.7/IREF0
P1.7
8
28
VDD_DIG
P1.6
9
27
VR_DIG
P1.5
10
26
GPIO_2
nIRQ
11
25
GPIO_1
XOUT
12
24
GPIO_0
XIN
13
23
GND_RF
N.C.
14
22
N.C.
Si1004/5
Top View
15
16
17
18
19
20
21
SDN
VDD_RF
TX
RXp
RXn
N.C.
ANT_A
GND
Figure 3.2. Si1004/5-E-GM2 Pinout Diagram (Top View)
34
Rev. 1.3
Si1000/1/2/3/4/5
Figure 3.3. LGA-42 Package Drawing (Si1000/1/2/3/4/5-E-GM2)
Rev. 1.3
35
Si1000/1/2/3/4/5
Table 3.2. LGA-42 Package Dimensions (Si1000/1/2/3/4/5-E-GM2)
Dimension
Min
Nom
Max
A
0.85
0.90
0.95
b
0.20
0.25
0.30
D
5.00 BSC.
D1
3.15
D2
3.00
D3
4.40
e
0.50 BSC.
E
7.00 BSC.
E1
5.40
E2
6.40
E3
6.50
L
0.35
0.40
0.45
L1
0.05
0.10
0.15
aaa
—
—
0.10
bbb
—
—
0.10
ccc
—
—
0.08
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C
specification for Small Body Components.
36
Rev. 1.3
Si1000/1/2/3/4/5
D1
(1.65)
E3
Y
E1
X
E2
E
D2
D3
Figure 3.4. LGA-42 PCB Land Pattern Dimensions (Si1000/1/2/3/4/5-E-GM2)
Rev. 1.3
37
Si1000/1/2/3/4/5
Table 3.3. LGA-42 PCB Land Pattern Dimensions (Si1000/1/2/3/4/5-E-GM2)
Dimension
mm
D1
3.15
D2
3.00
D3
4.40
E
0.50
E1
5.45
E2
6.40
E3
6.50
X
0.25
Y
0.50
Notes:
General
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. This Land Pattern Design is based on the IPC-7351 guidelines.
3. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition
(LMC) is calculated based on a Fabrication Allowance of 0.05 mm.
PCB Design
4. PCB design must ensure sufficient thermal relief for operation of the device.
5. Place vias in E-pad as shown in Figure 3.5.
Solder Mask Design
6. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder
mask and the metal pad is to be 60 µm minimum, all the way around the pad.
Stencil Design
7. Place ground pad openings as shown in Figure 3.5.
8. The stencil thickness should be 0.125 mm (5 mils).
9. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads.
10. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used
to assure good solder paste release.
Card Assembly
11. A No-Clean, Type-3 solder paste is recommended.
12. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for
Small Body Components.
38
Rev. 1.3
Si1000/1/2/3/4/5
2.420
1.210
Ø0.250
0.075
1.350
1.200
Center pad paste detail:
R 0.25
1.11
1.11
Figure 3.5. LGA-42 PCB Stencil and Via Placement
Rev. 1.3
39
Si1000/1/2/3/4/5
4. Electrical Characteristics
In sections 4.1 and 4.2, “VDD” refers to the VDD_MCU supply voltage on Si1000/1/2/3 devices and to the
VDD_MCU/DC+ supply voltage on Si1004/5 devices. The ADC, Comparator, and Port I/O specifications in
these two sections do not apply to the EZRadioPRO peripheral.
In sections 4.3 and 4.4, “VDD” refers to the VDD_RF and VDD_DIG Supply Voltage. All specifications in
these sections pertain to the EZRadioPRO peripheral.
4.1. Absolute Maximum Specifications
Table 4.1. Absolute Maximum Ratings
Parameter
Min
Typ
Max
Unit
Ambient Temperature under Bias
–55
—
125
°C
Storage Temperature
–65
—
150
°C
–0.3
–0.3
—
—
5.8
VDD + 3.6
V
–0.3
–0.3
—
—
2.0
4.0
V
–0.3
—
4.0
V
Maximum Total Current through
VBAT, DCEN, VDD_MCU/DC+ or
GND
—
—
500
mA
Maximum Output Current Sunk
by RST or any Px.x Pin
—
—
100
mA
Maximum Total Current through
all Px.x Pins
—
—
200
mA
DC-DC Converter Output Power
—
—
110
mW
All pins except TX, RXp,
and RXn
—
—
2
kV
TX, RXp, and RXn
—
—
1
kV
All pins except TX, RXp,
and RXn
—
—
150
V
TX, RXp, and RXn
—
—
45
V
Voltage on any Px.x I/O Pin or
RST with Respect to GND
Voltage on VBAT with respect to
GND
Test Condition
VDD > 2.2 V
VDD < 2.2 V
One-Cell Mode
Two-Cell Mode
Voltage on VDD_MCU or
VDD_MCU/DC+ with respect to
GND
ESD (Human Body Model)
ESD (Machine Model)
Note: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the devices at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
40
Rev. 1.3
Si1000/1/2/3/4/5
4.2. MCU Electrical Characteristics
Table 4.2. Global Electrical Characteristics
–40 to +85 °C, 25 MHz system clock unless otherwise specified. See "AN358: Optimizing Low Power Operation of the
‘F9xx" for details on how to achieve the supply current specifications listed in this table.
Parameter
Test Condition
Min
Typ
Max
Unit
Battery Supply Voltage (VBAT)
One-Cell Mode
Two-Cell Mode
0.9
1.8
1.2
2.4
1.8
3.6
V
Supply Voltage
(VDD_MCU/DC+)
One-Cell Mode
Two-Cell Mode
1.8
1.8
1.9
2.4
3.6
3.6
V
Minimum RAM Data 
Retention Voltage1
VDD (not in Sleep Mode)
VBAT (in Sleep Mode)
—
—
1.4
0.3
—
0.5
V
SYSCLK (System Clock)2
0
—
25
MHz
TSYSH (SYSCLK High Time)
18
—
—
ns
TSYSL (SYSCLK Low Time)
18
—
—
ns
Specified Operating 
Temperature Range
–40
—
+85
°C
Digital Supply Current—CPU Active (Normal Mode, fetching instructions from flash)
IDD 3, 4, 5, 6, 7, 8
IDD
7. 8
Frequency Sensitivity3, 5, 6,
VDD = 1.8–3.6 V, F = 24.5 MHz
(includes precision oscillator current)
—
4.1
5.0
mA
VDD = 1.8–3.6 V, F = 20 MHz
(includes low power oscillator current)
—
3.5
—
mA
VDD = 1.8 V, F = 1 MHz
VDD = 3.6 V, F = 1 MHz
(includes external oscillator/GPIO current)
—
—
295
365
—
—
µA
µA
VDD = 1.8–3.6 V, F = 32.768 kHz
(includes SmaRTClock oscillator current)
—
90
—
µA
VDD = 1.8–3.6 V, T = 25 °C,
F < 10 MHz (flash oneshot active, see
13.6)
—
226
—
µA/MHz
VDD = 1.8–3.6 V, T = 25 °C,
F > 10 MHz (flash oneshot bypassed,
see 13.6)
—
120
—
µA/MHz
Rev. 1.3
41
Si1000/1/2/3/4/5
Table 4.2. Global Electrical Characteristics (Continued)
–40 to +85 °C, 25 MHz system clock unless otherwise specified. See "AN358: Optimizing Low Power Operation of the
‘F9xx" for details on how to achieve the supply current specifications listed in this table.
Parameter
Test Condition
Min
Typ
Max
Unit
Digital Supply Current—CPU Inactive (Idle Mode, not fetching instructions from flash)
IDD4, 6,7,8
IDD Frequency Sensitivity1,6,8
VDD = 1.8–3.6 V, F = 24.5 MHz
(includes precision oscillator current)
—
2.5
3.0
mA
VDD = 1.8–3.6 V, F = 20 MHz
(includes low power oscillator current)
—
1.8
—
mA
VDD = 1.8 V, F = 1 MHz
VDD = 3.6 V, F = 1 MHz
(includes external oscillator/GPIO current)
—
—
165
235
—
—
µA
µA
VDD = 1.8–3.6 V, F = 32.768 kHz
(includes SmaRTClock oscillator
current)
—
84
—
µA
VDD = 1.8–3.6 V, T = 25 °C
—
95
—
µA/MHz
—
77
—
µA
Digital Supply Current—Suspend and Sleep Mode
Digital Supply Current6,7,8
(Suspend Mode)
VDD = 1.8–3.6 V, two-cell mode
Digital Supply Current8
(Sleep Mode, SmaRTClock
running)
1.8 V, T = 25 °C
3.0 V, T = 25 °C
3.6 V, T = 25 °C
1.8 V, T = 85 °C
3.0 V, T = 85 °C
3.6 V, T = 85 °C
(includes SmaRTClock oscillator and
brownout detector)
—
—
—
—
—
—
0.61
0.76
0.87
1.32
1.62
1.93
—
—
—
—
—
—
µA
Digital Supply Current8
(Sleep Mode)
1.8 V, T = 25 °C
3.0 V, T = 25 °C
3.6 V, T = 25 °C
1.8 V, T = 85 °C
3.0 V, T = 85 °C
3.6 V, T = 85 °C
(includes brownout detector)
—
—
—
—
—
—
0.06
0.09
0.14
0.77
0.92
1.23
—
—
—
—
—
—
µA
42
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.2. Global Electrical Characteristics (Continued)
–40 to +85 °C, 25 MHz system clock unless otherwise specified. See "AN358: Optimizing Low Power Operation of the
‘F9xx" for details on how to achieve the supply current specifications listed in this table.
Parameter
Test Condition
Min
Typ
Max
Unit
Notes:
1. Based on device characterization data; Not production tested.
2. SYSCLK must be at least 32 kHz to enable debugging.
3. Digital Supply Current depends upon the particular code being executed. The values in this table are obtained
with the CPU executing an “sjmp $” loop, which is the compiled form of a while(1) loop in C. One iteration
requires 3 CPU clock cycles, and the flash memory is read on each cycle. The supply current will vary slightly
based on the physical location of the sjmp instruction and the number of flash address lines that toggle as a
result. In the worst case, current can increase by up to 30% if the sjmp loop straddles a 128-byte flash
address boundary (e.g., 0x007F to 0x0080). Real-world code with larger loops and longer linear sequences
will have few transitions across the 128-byte address boundaries.
4. Includes oscillator and regulator supply current.
5. IDD can be estimated for frequencies <10 MHz by simply multiplying the frequency of interest by the
frequency sensitivity number for that range, then adding an offset of 90 µA. When using these numbers to
estimate IDD for >10 MHz, the estimate should be the current at 25 MHz minus the difference in current
indicated by the frequency sensitivity number. For example: VDD = 3.0 V; F = 20 MHz, IDD = 4.1 mA –
(25 MHz – 20 MHz) x 0.120 mA/MHz = 3.5 mA.
6. The Supply Voltage is the voltage at the VDD_MCU pin, typically 1.8 to 3.6 V (default = 1.9 V).
Idle IDD can be estimated by taking the current at 25 MHz minus the difference in current indicated by the
frequency sensitivity number. For example: VDD = 3.0 V; F = 5 MHz, Idle IDD = 2.5 mA – (25 MHz –
5 MHz) x 0.095 mA/MHz = 0.6 mA.
7. The supply current specifications in Table 4.2 are for two cell mode. The VBAT current in one-cell mode can
be estimated using the following equation:
Supply Voltage  Supply Current (two-cell mode)
VBAT Current (one-cell mode) = ----------------------------------------------------------------------------------------------------------------------------------DC-DC Converter Efficiency  VBAT Voltage
The VBAT Voltage is the voltage at the VBAT pin, typically 0.9 to 1.8 V.
The Supply Current (two-cell mode) is the data sheet specification for supply current.
The Supply Voltage is the voltage at the VDD/DC+ pin, typically 1.8 to 3.3 V (default = 1.9 V).
The DC-DC Converter Efficiency can be estimated using Figure 4.3–Figure 4.5.
8. The EZRadioPRO peripheral is placed in Shutdown mode.
Rev. 1.3
43
Si1000/1/2/3/4/5
4200
F < 10 MHz
Oneshot Enabled
4100
4000
F > 10 MHz
Oneshot Bypassed
3900
3800
3700
3600
3500
3400
< 170 µA/MHz
3300
3200
3100
3000
200 µA/MHz
2900
2800
2700
2600
215 µA/MHz
Supply Current (uA)
2500
2400
2300
2200
2100
2000
1900
1800
1700
1600
1500
1400
240 µA/MHz
1300
1200
1100
1000
900
250 µA/MHz
800
700
600
500
400
300
300 µA/MHz
200
100
0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Frequency (MHz)
Figure 4.1. Active Mode Current (External CMOS Clock)
44
Rev. 1.3
21
22
23
24
25
Si1000/1/2/3/4/5
Supply Current vs. Frequency
4200
4100
4000
3900
3800
3700
3600
3500
3400
3300
3200
3100
3000
2900
2800
2700
2600
Supply Current (uA)
2500
2400
2300
2200
2100
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Frequency (MHz)
Figure 4.2. Idle Mode Current (External CMOS Clock)
Rev. 1.3
45
Si1000/1/2/3/4/5
6:6(/ 6:6(/ Efficiency (%)
9%$7 9
9%$7 9
9%$7 9
9%$7 9
9%$7 9
9%$7 9
9%$7 9
X+,QGXFWRUSDFNDJH(65 2KPV
9'''& 90LQLPXP3XOVH:LGWK QV3XOVH6NLSSLQJ'LVDEOHG
1RWH(IILFLHQF\DWKLJKFXUUHQWVPD\EHLPSURYHGE\FKRRVLQJDQ
LQGXFWRUZLWKDORZHU(65
Load Current (mA)
Figure 4.3. Typical DC-DC Converter Efficiency (High Current, VDD/DC+ = 2 V
46
Rev. 1.3
Si1000/1/2/3/4/5
6:6(/ 6:6(/ 9%$7 9
Efficiency (%)
9%$7 9
9%$7 9
9%$7 9
9%$7 9
9%$7 9
9%$7 9
X+,QGXFWRUSDFNDJH(65 2KPV
9'''& 90LQLPXP3XOVH:LGWK QV
3XOVH6NLSSLQJ'LVDEOHG
1RWH(IILFLHQF\DWKLJKFXUUHQWVPD\EHLPSURYHGE\
FKRRVLQJDQLQGXFWRUZLWKDORZHU(65
Load current (mA)
Figure 4.4. Typical DC-DC Converter Efficiency (High Current, VDD/DC+ = 3 V)
Rev. 1.3
47
Si1000/1/2/3/4/5
9%$7 9
9%$7 9
Efficiency (%)
9%$7 9
9%$7 9
9%$7 9
9%$7 9
9%$7 9
X+,QGXFWRUSDFNDJH(65 2KPV
6:6(/ 9'''& 90LQLPXP3XOVH:LGWK QV
Load current (mA)
Figure 4.5. Typical DC-DC Converter Efficiency (Low Current, VDD/DC+ = 2 V)
48
Rev. 1.3
Si1000/1/2/3/4/5
X+,QGXFWRUSDFNDJH(65 2KPV
6:6(/ 9'''& 9/RDG&XUUHQW X$
0LQ3XOVH:LGWKQV
0LQ3XOVH:LGWKQV
0LQ3XOVH:LGWKQV
0LQ3XOVH:LGWKQV
9%$7&XUUHQWX$
9%$79
Figure 4.6. Typical One-Cell Suspend Mode Current
Rev. 1.3
49
Si1000/1/2/3/4/5
Table 4.3. Port I/O DC Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise specified.
Parameters
Test Condition
Output High Voltage High Drive Strength, PnDRV.n = 1
IOH = –3 mA, Port I/O push-pull
IOH = –10 µA, Port I/O push-pull
IOH = –10 mA, Port I/O push-pull
Low Drive Strength, PnDRV.n = 0
IOH = –1 mA, Port I/O push-pull
IOH = –10 µA, Port I/O push-pull
IOH = –3 mA, Port I/O push-pull
Min
Typ
Max
VDD – 0.7
VDD – 0.1
—
—
See Chart
—
—
—
VDD – 0.7
—
VDD – 0.1
See Chart
—
—
—
—
Unit
V
Output Low Voltage High Drive Strength, PnDRV.n = 1
IOL = 8.5 mA
IOL = 10 µA
IOL = 25 mA
—
—
—
—
—
See Chart
0.6
0.1
—
Low Drive Strength, PnDRV.n = 0
IOL = 1.4 mA
IOL = 10 µA
IOL = 4 mA
—
—
—
—
—
See Chart
0.6
0.1
—
VDD = 2.0 to 3.6 V
VDD – 0.6
—
—
V
VDD = 0.9 to 2.0 V
0.7 x VDD
—
—
V
VDD = 2.0 to 3.6 V
—
—
0.6
V
VDD = 0.9 to 2.0 V
—
—
0.3 x VDD
V
Weak Pullup On, VIN = 0 V, VDD = 1.8 V
Weak Pullup On, Vin = 0 V, VDD = 3.6 V
—
—
4
20
—
30
µA
Input High Voltage
Input Low Voltage
Input Leakage 
Current
50
Rev. 1.3
V
Si1000/1/2/3/4/5
Typical VOH (High Drive Mode)
Voltage
3.6
3.3
VDD = 3.6V
3
VDD = 3.0V
2.7
VDD = 2.4V
2.4
VDD = 1.8V
2.1
1.8
1.5
1.2
0.9
0
5
10
15
20
25
30
35
40
45
50
Load Current (mA)
Typical VOH (Low Drive Mode)
Voltage
3.6
3.3
VDD = 3.6V
3
VDD = 3.0V
2.7
VDD = 2.4V
2.4
VDD = 1.8V
2.1
1.8
1.5
1.2
0.9
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
Load Current (mA)
Figure 4.7. Typical VOH Curves, 1.8–3.6 V
Rev. 1.3
51
Si1000/1/2/3/4/5
Typical VOH (High Drive Mode)
1.8
VDD = 1.8V
1.7
1.6
VDD = 1.5V
1.5
1.4
VDD = 1.2V
Voltage
1.3
VDD = 0.9V
1.2
1.1
1
0.9
0.8
0.7
0.6
0.5
0
1
2
3
4
5
6
7
8
9
10
11
12
Load Current (mA)
Typical VOH (Low Drive Mode)
1.8
1.7
VDD = 1.8V
1.6
VDD = 1.5V
1.5
1.4
VDD = 1.2V
Voltage
1.3
1.2
VDD = 0.9V
1.1
1
0.9
0.8
0.7
0.6
0.5
0
1
2
3
Load Current (mA)
Figure 4.8. Typical VOH Curves, 0.9–1.8 V
52
Rev. 1.3
Si1000/1/2/3/4/5
Typical VOL (High Drive Mode)
1.8
VDD = 3.6V
1.5
VDD = 3.0V
Voltage
1.2
VDD = 2.4V
VDD = 1.8V
0.9
0.6
0.3
0
-80
-70
-60
-50
-40
-30
-20
-10
0
Load Current (mA)
Typical VOL (Low Drive Mode)
1.8
VDD = 3.6V
1.5
VDD = 3.0V
Voltage
1.2
VDD = 2.4V
VDD = 1.8V
0.9
0.6
0.3
0
-10
-9
-8
-7
-6
-5
-4
-3
-2
-1
0
Load Current (mA)
Figure 4.9. Typical VOL Curves, 1.8–3.6 V
Rev. 1.3
53
Si1000/1/2/3/4/5
Typical VOL (High Drive Mode)
1.8
VDD = 3.6V
1.5
VDD = 3.0V
Voltage
1.2
VDD = 2.4V
VDD = 1.8V
0.9
0.6
0.3
0
-80
-70
-60
-50
-40
-30
-20
-10
0
Load Current (mA)
Typical VOL (Low Drive Mode)
1.8
VDD = 3.6V
1.5
VDD = 3.0V
Voltage
1.2
VDD = 2.4V
VDD = 1.8V
0.9
0.6
0.3
0
-10
-9
-8
-7
-6
-5
-4
-3
-2
-1
0
Load Current (mA)
Figure 4.10. Typical VOL Curves, 1.8–3.6 V
54
Rev. 1.3
Si1000/1/2/3/4/5
Typical VOL (High Drive Mode)
0.5
VDD = 1.8V
Voltage
0.4
VDD = 1.5V
VDD = 1.2V
0.3
VDD = 0.9V
0.2
0.1
0
-5
-4
-3
-2
-1
0
Load Current (mA)
Typical VOL (Low Drive Mode)
0.5
Voltage
0.4
0.3
VDD = 1.8V
0.2
VDD = 1.5V
VDD = 1.2V
0.1
VDD = 0.9V
0
-3
-2
-1
0
Load Current (mA)
Figure 4.11. Typical VOL Curves, 0.9–1.8 V
Rev. 1.3
55
Si1000/1/2/3/4/5
Table 4.4. Reset Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise specified.
Parameter
Test Condition
Min
Typ
Max
Unit
RST Output Low Voltage
IOL = 1.4 mA,
—
—
0.6
V
RST Input High Voltage
VDD = 2.0 to 3.6 V
VDD – 0.6
—
—
V
VDD = 0.9 to 2.0 V
0.7 x VDD
—
—
V
VDD = 2.0 to 3.6 V
—
—
0.6
V
VDD = 0.9 to 2.0 V
—
—
0.3 x VDD
V
RST = 0.0 V, VDD = 1.8 V
RST = 0.0 V, VDD = 3.6 V
—
—
4
20
—
30
µA
Early Warning
Reset Trigger
(all power modes except Sleep)
1.8
1.7
1.85
1.75
1.9
1.8
V
VDD Ramp Time for Power
On
One-cell Mode: VBAT Ramp 0–0.9 V
Two-cell Mode: VBAT Ramp 0–1.8 V
—
—
3
ms
VDD Monitor Threshold
(VPOR)
Initial Power-On (VDD Rising)
Brownout Condition (VDD Falling)
Recovery from Brownout (VDD Rising)
—
0.7
—
0.75
0.8
0.95
—
0.9
—
V
Missing Clock Detector
Timeout
Time from last system clock rising edge
to reset initiation
100
650
1000
µs
Minimum System Clock w/
Missing Clock Detector
Enabled
System clock frequency which triggers
a missing clock detector timeout
—
7
10
kHz
Delay between release of any reset
source and code
execution at location 0x0000
—
10
—
µs
Minimum RST Low Time to
Generate a System Reset
15
—
—
µs
VDD Monitor Turn-on Time
—
300
—
ns
VDD Monitor Supply 
Current
—
7
—
µA
RST Input Low Voltage
RST Input Pullup Current
VDD_MCU Monitor
Threshold (VRST)
Reset Time Delay
56
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.5. Power Management Electrical Specifications
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise specified.
Parameter
Test Condition
Min
Typ
Max
Unit
2
—
3
SYSCLKs
Low power oscillator
—
400
—
ns
Precision oscillator
—
1.3
—
µs
Two-cell mode
—
2
—
µs
One-cell mode
—
10
—
µs
Idle Mode Wake-up Time
Suspend Mode Wake-up Time
Sleep Mode Wake-up Time
Table 4.6. Flash Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise specified.
Parameter
Test Condition
Min
Typ
Max
Unit
Si1000/2/4
65536*
—
—
bytes
Si1001/3/5
32768
—
—
bytes
1024
—
1024
bytes
Endurance
1k
30k
—
Erase/Write
Cycles
Erase Cycle Time
28
32
36
ms
Write Cycle Time
57
64
71
µs
Flash Size
Scratchpad Size
Note: 1024 bytes at addresses 0xFC00 to 0xFFFF are reserved.
Rev. 1.3
57
Si1000/1/2/3/4/5
Table 4.7. Internal Precision Oscillator Electrical Characteristics
VDD = 1.8 to 3.6 V; TA = –40 to +85 °C unless otherwise specified; Using factory-calibrated settings.
Parameter
Oscillator Frequency
Oscillator Supply Current 
(from VDD)
Test Condition
Min
Typ
Max
Unit
–40 to +85 °C,
VDD = 1.8–3.6 V
25 °C; includes bias current
of 90–100 µA
24
24.5
25
MHz
—
300*
—
µA
*Note: Does not include clock divider or clock tree supply current.
Table 4.8. Internal Low-Power Oscillator Electrical Characteristics
VDD = 1.8 to 3.6 V; TA = –40 to +85 °C unless otherwise specified; Using factory-calibrated settings.
Parameter
Oscillator Frequency
Oscillator Supply Current 
(from VDD)
Test Condition
Min
Typ
Max
Unit
–40 to +85 °C,
VDD = 1.8–3.6 V
25 °C
No separate bias current
required.
18
20
22
MHz
—
100*
—
µA
*Note: Does not include clock divider or clock tree supply current.
58
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.9. ADC0 Electrical Characteristics
VDD = 1.8 to 3.6V V, VREF = 1.65 V (REFSL[1:0] = 11), –40 to +85 °C unless otherwise specified.
Parameter
Test Condition
Min
Typ
Max
Unit
DC Accuracy
Resolution
10
Integral Nonlinearity
bits
—
±0.5
±1
LSB
—
±0.5
±1
LSB
Offset Error
—
±<1
±2
LSB
Full Scale Error
—
±1
±2.5
LSB
Differential Nonlinearity
Guaranteed Monotonic
Dynamic performance (10 kHz sine-wave single-ended input, 1 dB below Full Scale, 300 ksps)
Signal-to-Noise Plus Distortion
54
58
—
dB
Signal-to-Distortion
—
73
—
dB
Spurious-Free Dynamic Range
—
75
—
dB
—
—
7.33
MHz
13
11
—
—
—
—
clocks
Track/Hold Acquisition Time
1.5
—
—
us
Throughput Rate
—
—
300
ksps
Single Ended (AIN+ – GND)
0
—
VREF
V
Single Ended
0
—
VDD
V
1x Gain
0.5x Gain
—
30
28
—
pF
—
5
—
k
Conversion Rate
SAR Conversion Clock
Conversion Time in SAR Clocks
10-bit Mode
8-bit Mode
Analog Inputs
ADC Input Voltage Range
Absolute Pin Voltage with respect
to GND
Sampling Capacitance
Input Multiplexer Impedance
Power Specifications
Power Supply Current 
(VDD supplied to ADC0)
Conversion Mode (300 ksps)
Tracking Mode (0 ksps)
—
—
800
680
—
—
µA
Power Supply Rejection
Internal High Speed VREF
External VREF
—
—
67
74
—
—
dB
Rev. 1.3
59
Si1000/1/2/3/4/5
Table 4.10. Temperature Sensor Electrical Characteristics
VDD = 1.8 to 3.6V V, –40 to +85 °C unless otherwise specified.
Parameter
Test Condition
Linearity
Slope
Slope Error
1
Min
Typ
Max
Unit
—
±1
—
°C
—
3.40
—
mV/°C
—
40
—
µV/°C
Offset
Temp = 25 °C
—
1025
—
mV
Offset Error1
Temp = 25 °C
—
18
—
mV
Initial Voltage=0 V
Initial Voltage=3.6 V
—
—
3.0
6.5
µs
—
35
—
µA
Temperature Sensor Settling
Time2
Supply Current
Notes:
1. Represents one standard deviation from the mean.
2. The temperature sensor settling time, resulting from an ADC mux change or enabling of the temperature
sensor, varies with the voltage of the previously sampled channel and can be up to 6.5 µs if the previously
sampled channel voltage was greater than 3 V. To minimize the temperature sensor settling time, the ADC
mux can be momentarily set to ground before being set to the temperature sensor output. This ensures that
the temperature sensor output will settle in 3 µs or less.
Table 4.11. Voltage Reference Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise specified.
Parameter
Test Condition
Internal High-Speed Reference (REFSL[1:0] = 11)
–40 to +85 °C,
Output Voltage
VDD = 1.8–3.6 V
VREF Turn-on Time
Supply Current
Internal Precision Reference (REFSL[1:0] = 00, REFOE = 1)
–40 to +85 °C,
Output Voltage
VDD = 1.8–3.6 V
VREF Short-Circuit Current
Load = 0 to 200 µA to AGND
Load Regulation
VREF Turn-on Time 1
VREF Turn-on Time 2
VREF Turn-on Time 3
4.7 µF tantalum, 0.1 µF ceramic
bypass, settling to 0.5 LSB
0.1 µF ceramic bypass, settling to
0.5 LSB
no bypass cap, settling to 0.5 LSB
Supply Current
Min
Typ
Max
Unit
1.60
1.65
1.70
V
—
—
1.7
µs
—
200
—
µA
1.645
1.680
1.715
V
—
3.5
—
mA
—
400
—
µV/µA
—
15
—
ms
—
300
—
µs
—
25
—
µs
—
15
—
µA
0
—
VDD
V
—
5.25
—
µA
External Reference (REFSL[1:0] = 00, REFOE = 0)
Input Voltage Range
Input Current
60
Sample Rate = 300 ksps; VREF =
3.0 V
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.12. IREF0 Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C, unless otherwise specified.
Parameter
Test Condition
Min
Typ
Max
Unit
Static Performance
Resolution
Output Compliance Range
6
bits
Low Power Mode, Source
0
—
VDD – 0.4
V
High Current Mode, Source
0
—
VDD – 0.8
V
Low Power Mode, Sink
0.3
—
VDD
V
High Current Mode, Sink
0.8
—
VDD
V
Integral Nonlinearity
—
<±0.2
±1.0
LSB
Differential Nonlinearity
—
<±0.2
±1.0
LSB
Offset Error
—
<±0.1
±0.5
LSB
Low Power Mode, Source
—
—
±5
%
High Current Mode, Source
—
—
±6
%
Low Power Mode, Sink
—
—
±8
%
High Current Mode, Sink
—
—
±8
%
Low Power Mode
Sourcing 20 µA
—
<±1
±3
%
Output Settling Time to 1/2 LSB
—
300
—
ns
Startup Time
—
1
—
µs
IREF0DAT = 000001
—
10
—
µA
IREF0DAT = 111111
—
10
—
µA
IREF0DAT = 000001
—
10
—
µA
IREF0DAT = 111111
—
10
—
µA
IREF0DAT = 000001
—
1
—
µA
IREF0DAT = 111111
—
11
—
µA
Full Scale Error*
Absolute Current Error
Dynamic Performance
Power Consumption
Net Power Supply Current 
(VDD supplied to IREF0 minus
any output source current)
Low Power Mode, Source
High Current Mode, Source
Low Power Mode, Sink
High Current Mode, Sink
IREF0DAT = 000001
—
12
—
µA
IREF0DAT = 111111
—
81
—
µA
*Note: Full scale is 63 µA in low power mode and 504 µA in high power mode.
Rev. 1.3
61
Si1000/1/2/3/4/5
Table 4.13. Comparator Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise noted.
Parameter
Test Condition
Min
Typ
Max
Unit
Response Time:
Mode 0, VDD = 2.4 V, VCM* = 1.2 V
CP0+ – CP0– = 100 mV
—
130
—
ns
CP0+ – CP0– = –100 mV
—
200
—
ns
CP0+ – CP0– = 100 mV
—
210
—
ns
CP0+ – CP0– = –100 mV
—
410
—
ns
CP0+ – CP0– = 100 mV
—
420
—
ns
CP0+ – CP0– = –100 mV
—
1200
—
ns
CP0+ – CP0– = 100 mV
—
1750
—
ns
CP0+ – CP0– = –100 mV
—
6200
—
ns
Common-Mode Rejection Ratio
—
1.5
4
mV/V
Inverting or Non-Inverting Input
Voltage Range
–0.25
—
VDD + 0.25
V
Input Capacitance
—
12
—
pF
Input Bias Current
—
1
—
nA
Input Offset Voltage
–7
—
+7
mV
—
0.1
—
mV/V
VDD = 3.6 V
—
0.6
—
µs
VDD = 3.0 V
—
1.0
—
µs
VDD = 2.4 V
—
1.8
—
µs
VDD = 1.8 V
—
10
—
µs
Mode 0
—
23
—
µA
Mode 1
—
8.8
—
µA
Mode 2
—
2.6
—
µA
Mode 3
—
0.4
—
µA
Response Time:
Mode 1, VDD = 2.4 V, VCM* = 1.2 V
Response Time:
Mode 2, VDD = 2.4 V, VCM* = 1.2 V
Response Time:
Mode 3, VDD = 2.4 V, VCM* = 1.2 V
Power Supply
Power Supply Rejection
Power-up Time
Supply Current at DC
Note: Vcm is the common-mode voltage on CP0+ and CP0–.
62
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.13. Comparator Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise noted.
Parameter
Test Condition
Min
Typ
Max
Unit
Hysteresis 1
(CPnHYP/N1–0 = 00)
—
0
—
mV
Hysteresis 2
(CPnHYP/N1–0 = 01)
—
8.5
—
mV
Hysteresis 3
(CPnHYP/N1–0 = 10)
—
17
—
mV
Hysteresis 4
(CPnHYP/N1–0 = 11)
—
34
—
mV
Hysteresis 1
(CPnHYP/N1–0 = 00)
—
0
—
mV
Hysteresis 2
(CPnHYP/N1–0 = 01)
—
6.5
—
mV
Hysteresis 3
(CPnHYP/N1–0 = 10)
—
13
—
mV
Hysteresis 4
(CPnHYP/N1–0 = 11)
—
26
—
mV
Hysteresis 1
(CPnHYP/N1–0 = 00)
—
0
1
mV
Hysteresis 2
(CPnHYP/N1–0 = 01)
2
5
10
mV
Hysteresis 3
(CPnHYP/N1–0 = 10)
5
10
20
mV
Hysteresis 4
(CPnHYP/N1–0 = 11)
12
20
30
mV
Hysteresis 1
(CPnHYP/N1–0 = 00)
—
0
—
mV
Hysteresis 2
(CPnHYP/N1–0 = 01)
—
4.5
—
mV
Hysteresis 3
(CPnHYP/N1–0 = 10)
—
9
—
mV
Hysteresis 4
(CPnHYP/N1–0 = 11)
—
17
—
mV
Hysteresis
Mode 0
Mode 1
Mode 2
Mode 3
Note: Vcm is the common-mode voltage on CP0+ and CP0–.
Rev. 1.3
63
Si1000/1/2/3/4/5
Table 4.14. DC-DC Converter (DC0) Electrical Characteristics
VBAT = 0.9 to 1.8 V, –40 to +85 °C unless otherwise specified.
Parameter
Test Condition
Min
Typ
Max
Unit
Input Voltage Range
0.9
—
1.8
V
Input Inductor Value
500
680
900
nH
Input Inductor Current
Rating
250
—
—
mA
—
—
0.5

Source Impedance < 2 
—
—
4.7
1.0
—
—
µF
Target Output = 1.8 V
1.73
1.80
1.87
V
Target Output = 1.9 V
1.83
1.90
1.97
V
Target Output = 2.0 V
1.93
2.00
2.07
V
Target Output = 2.1 V
2.03
2.10
2.17
V
Target Output = 2.1 V
2.30
2.40
2.50
V
Target Output = 2.7 V
2.60
2.70
2.80
V
Target Output = 3.0 V
2.90
3.00
3.10
V
Target Output = 3.3 V
3.18
3.30
3.42
V
Target Output = 2.0 V, 1 to 30 mA
—
±0.3
—
%
Target Output = 3.0 V, 1 to 20 mA
—
±1
—
%
Target Output = 1.8 V
—
—
36
mA
Target Output = 1.9 V
—
—
34
mA
Target Output = 2.0 V
—
—
32
mA
Target Output = 2.1 V
—
—
30
mA
Target Output = 2.4 V
—
—
27
mA
Target Output = 2.7 V
—
—
24
mA
Target Output = 3.0 V
—
—
21
mA
Target Output = 3.3 V
—
—
19
mA
—
—
65
mW
—
—
80
100
—
—
µA
Clocking Frequency
1.6
2.4
3.2
MHz
Maximum DC Load Current
During Startup
—
—
1
mA
Capacitance Connected to
Output
0.8
1.0
2.0
µF
Inductor DC Resistance
Input Capacitor Value
Output Voltage Range
Output Load Regulation
Output Current 
(based on output power
spec)
Output Power
Bias Current
64
from VBAT supply
from VDD/DC+ supply
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.15. VREG0 Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise specified.
Parameter
Test Condition
Input Voltage Range
Bias Current
Normal, Idle, Suspend, or Stop Mode
Rev. 1.3
Min
Typ
Max
Unit
1.8
—
3.6
V
—
20
—
µA
65
Si1000/1/2/3/4/5
4.3. EZRadioPRO® Electrical Characteristics
Table 4.16. DC Characteristics1
Parameter
Supply Voltage
Range
Symbol
Min
Typ
Max
Unit
1.8
3.0
3.6
V
RC Oscillator, Main Digital Regulator,
and Low Power Digital Regulator OFF
—
15
50
nA
IStandby
Low Power Digital Regulator ON (Register
values retained) and Main Digital
Regulator, and RC Oscillator OFF
—
450
800
nA
ISleep
RC Oscillator and Low Power Digital
Regulator ON
(Register values retained) and Main Digital
Regulator OFF
—
1
—
µA
ISensor-
Main Digital Regulator and Low Battery
Detector ON,
Crystal Oscillator and all other blocks
OFF2
—
1
—
µA
ISensor-TS
Main Digital Regulator and Temperature
Sensor ON,
Crystal Oscillator and all other blocks
OFF2
—
1
—
µA
IReady
Crystal Oscillator and Main Digital
Regulator ON,
all other blocks OFF. Crystal Oscillator
buffer disabled
—
800
—
µA
ITune
Synthesizer and regulators enabled
VDD
Power Saving Modes IShutdown
LBD
TUNE Mode Current
Test Condition
—
8.5
—
mA
—
18.5
—
mA
txpow[2:0] = 111 (+20 dBm)
Using Silicon Labs’ Reference Design.
TX current consumption is dependent on
match and board layout.
—
85
—
mA
ITX_+13
txpow[2:0] = 110 (+13 dBm)
Using Silicon Labs’ Reference Design.
TX current consumption is dependent on
match and board layout.
—
30
—
mA
ITX_+1
txpow[2:0] = 010 (+1 dBm)
Using Silicon Labs’ Reference Design.
TX current consumption is dependent on
match and board layout.
—
17
—
mA
RX Mode Current
IRX
TX Mode Current
—Si1000/1
ITX_+20
TX Mode Current
—Si1002/3
Notes:
1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max
limits are listed in the "Production Test Conditions" section on page 73.
2. Guaranteed by qualification. Qualification test conditions are listed in the "Production Test Conditions"
section on page 73.
66
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.17. Synthesizer AC Electrical Characteristics1
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
240
—
960
MHz
Synthesizer Frequency
Range
FSYN
Synthesizer Frequency
Resolution2
FRES-LB
Low Band, 240–480 MHz
—
156.25
—
Hz
FRES-HB
High Band, 480–960 MHz
—
312.5
—
Hz
fREF_LV
When using external reference
signal driving XOUT pin, instead
of using crystal. Measured peakto-peak (VPP)
0.7
—
1.6
V
Synthesizer Settling Time2
tLOCK
Measured from exiting Ready
mode with XOSC running to any
frequency.
Including VCO Calibration.
—
200
—
µs
Residual FM2
FRMS
Integrated over 250 kHz bandwidth (500 Hz lower bound of
integration)
—
2
4
kHzRMS
Phase Noise2
L(fM)
F = 10 kHz
—
–80
—
dBc/Hz
F = 100 kHz
—
–90
—
dBc/Hz
F = 1 MHz
—
–115
—
dBc/Hz
F = 10 MHz
—
–130
—
dBc/Hz
Reference Frequency
Input Level2
Notes:
1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max
limits are listed in the "Production Test Conditions" section on page 73.
2. Guaranteed by qualification. Qualification test conditions are listed in the "Production Test Conditions" section
on page 73.
Rev. 1.3
67
Si1000/1/2/3/4/5
Table 4.18. Receiver AC Electrical Characteristics1
Parameter
RX Frequency Range
RX Sensitivity2
Symbol
FRX
PRX_2
PRX_40
PRX_100
PRX_125
PRX_OOK
Test Condition
(BER < 0.1%)
(2 kbps, GFSK, BT = 0.5,
f = 5 kHz)3
(BER < 0.1%)
(40 kbps, GFSK, BT = 0.5,
f = 20 kHz)3
(BER < 0.1%)
(100 kbps, GFSK, BT = 0.5,
f = 50 kHz)3
(BER < 0.1%)
(125 kbps, GFSK, BT = 0.5,
f = 62.5 kHz)
(BER < 0.1%)
(4.8 kbps, 350 kHz BW, OOK)3
(BER < 0.1%)
(40 kbps, 400 kHz BW, OOK)3
RX Channel Bandwidth3
BER Variation vs Power
Level3
LNA Input Impedance3
(Unmatched—measured
differentially across RX
input pins)
BW
PRX_RES
Up to +5 dBm Input Level
RIN-RX
915 MHz
RSSI Resolution
1-Ch Offset Selectivity3
RESRSSI
C/I1-CH
868 MHz
433 MHz
315 MHz
Desired Ref Signal 3 dB above
sensitivity, BER < 0.1%. Interferer
3
2-Ch Offset Selectivity
C/I2-CH
and desired modulated with
3
 3-Ch Offset Selectivity
C/I3-CH 40 kbps F = 20 kHz GFSK with BT
= 0.5, channel spacing = 150 kHz
3
Desired Ref Signal 3 dB above
Blocking at 1 MHz Offset 1MBLOCK
sensitivity. Interferer and desired
3
Blocking at 4 MHz Offset 4MBLOCK
modulated with 40 kbps F =
Blocking at 8 MHz Offset3 8MBLOCK
20 kHz GFSK with BT = 0.5
Rejection at the image frequency.
Image Rejection3
ImREJ
IF=937 kHz
Measured at RX pins
Spurious Emissions3
POB_RX1
Min
240
—
Typ
—
–121
Max
960
—
Unit
MHz
dBm
—
–108
—
dBm
—
–104
—
dBm
—
–101
—
dBm
—
–110
—
dBm
—
–102
—
dBm
2.6
—
—
0
620
0.1
kHz
ppm
—
—
—
—
—
—
51–60j
54–63j
89–110j
107–137j
±0.5
–31
—
—
—
—
—
—

dB
dB
—
–35
—
dB
—
–40
—
dB
—
–52
—
dB
—
–56
—
dB
—
–63
—
dB
—
–30
—
dB
—
—
–54
dBm
Notes:
1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max
limits are listed in the "Production Test Conditions" section on page 73.
2. Receive sensitivity at multiples of 30 MHz may be degraded. If channels with a multiple of 30 MHz are required
it is recommended to shift the crystal frequency. Contact Silicon Labs Applications Support for
recommendations.
3. Guaranteed by qualification. Qualification test conditions are listed in the "Production Test Conditions" section
on page 73.
68
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.19. Transmitter AC Electrical Characteristics1
Parameter
Symbol
TX Frequency Range
FSK Data Rate2
OOK Data Rate2
Modulation Deviation
Modulation Deviation 
Resolution2
Output Power Range—
Si1000/13
Output Power Range—
Si1002/33
TX RF Output Steps2
Test Condition
Min
Typ
Max
Unit
FTX
240
—
960
MHz
DRFSK
0.123
—
256
kbps
DROOK
0.123
—
40
kbps
±320
kHz
∆f1
860–960 MHz
±0.625
∆f2
240–860 MHz
±0.625
±160
kHz
∆fRES
—
0.625
—
kHz
PTX
+1
—
+20
dBm
PTX
–4
—
+13
dBm
PRF_OUT
controlled by txpow[2:0]
—
3
—
dB
PRF_TEMP
–40 to +85 C
—
2
—
dB
PRF_FREQ
Measured across any one
frequency band
—
1
—
dB
Transmit Modulation 
Filtering2
B*T
Gaussian Filtering Bandwith
Time
Product
—
0.5
—
Spurious Emissions2
POB-TX1
POUT = 11 dBm,
Frequencies <1 GHz
—
—
–54
dBm
POB-TX2
1–12.75 GHz, excluding
harmonics
—
—
–54
dBm
P2HARM
Using reference design TX
matching network and filter
with max output power. Harmonics reduce linearly with
output power.
—
—
–42
dBm
—
—
–42
dBm
2
TX RF Output Level
Variation vs. Temperature
TX RF Output Level
Variation vs. Frequency2
Harmonics2
P3HARM
Notes:
1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max
limits are listed in the "Production Test Conditions" section on page 73.
2. Guaranteed by qualification. Qualification test conditions are listed in the "Production Test Conditions" section
on page 73.
3. Output power is dependent on matching components, board layout, and is measured at the pin.
Rev. 1.3
69
Si1000/1/2/3/4/5
Table 4.20. Auxiliary Block Specifications1
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Temperature Sensor 
Accuracy2
TSA
After calibrated via sensor offset register
tvoffs[7:0]
—
0.5
—
°C
Temperature Sensor 
Sensitivity2
TSS
—
5
—
mV/°C
Low Battery Detector 
Resolution2
LBDRES
—
50
—
mV
Low Battery Detector 
Conversion Time2
LBDCT
—
250
—
µs
Microcontroller Clock 
Output Frequency
FMC
32.768K
—
30M
Hz
Configurable to
30 MHz, 15 MHz,
10 MHz, 4 MHz, 3 MHz,
2 MHz, 1 MHz, or
32.768 kHz
General Purpose ADC Resolution2
ADCENB
—
8
—
bit
General Purpose ADC Bit
Resolution2
ADCRES
—
4
—
mV/bit
Temp Sensor & General Purpose ADC Conversion Time2
ADCCT
—
305
—
µs
30 MHz XTAL Start-Up Time
t30M
Using XTAL and board
layout in reference
design. Start-up time
will vary with XTAL type
and board layout.
—
600
—
µs
30MRES
See Section
“23.5.8. Crystal Oscillator” on page 263 for
total load capacitance
calculation
—
97
—
fF
—
6
—
sec
32 kHz Accuracy using Inter- 32KRCRE
nal RC Oscillator2
S
—
1000
—
ppm
32 kHz RC Oscillator StartUp
t32kRC
—
500
—
µs
tPOR
—
9.5
—
ms
tsoft
—
250
—
µs
30 MHz XTAL Cap 
Resolution2
32 kHz XTAL Start-Up Time2
POR Reset Time
Software Reset
Time2
t32k
Notes:
1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max
limits are listed in the "Production Test Conditions" section on page 73.
2. Guaranteed by qualification. Qualification test conditions are listed in the "Production Test Conditions" section
on page 73.
70
Rev. 1.3
Si1000/1/2/3/4/5
Table 4.21. Digital IO Specifications (nIRQ)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Rise Time
TRISE
0.1 x VDD to 0.9 x VDD, CL= 5 pF
—
—
8
ns
Fall Time
TFALL
0.9 x VDD to 0.1 x VDD, CL= 5 pF
—
—
8
ns
Input Capacitance
CIN
—
—
1
pF
Logic High Level Input
Voltage
Logic Low Level Input
Voltage
Input Current
VIH
VDD – 0.6
—
—
V
—
0.6
V
IIN
0<VIN< VDD
–100
—
100
nA
Logic High Level 
Output Voltage
Logic Low Level 
Output Voltage
VOH
IOH<1 mA source, VDD=1.8 V
VDD – 0.6
—
—
V
VOL
IOL<1 mA sink, VDD=1.8 V
—
—
0.6
V
VIL
Note: All specifications guaranteed by qualification. Qualification test conditions are listed in the "Production Test
Conditions" section on page 73.
Table 4.22. GPIO Specifications (GPIO_0, GPIO_1, and GPIO_2)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Rise Time
TRISE
0.1 x VDD to 0.9 x VDD,
CL= 10 pF, DRV<1:0>=HH
—
—
8
ns
Fall Time
TFALL
0.9 x VDD to 0.1 x VDD,
CL= 10 pF, DRV<1:0>=HH
—
—
8
ns
1
pF
Input Capacitance
CIN
—
—
Logic High Level Input
Voltage
Logic Low Level Input
Voltage
Input Current
VIH
VDD – 0.6
—
VIL
—
—
0.6
V
IIN
0<VIN< VDD
–100
—
100
nA
Input Current If Pullup is
Activated
Maximum Output Current
IINP
VIL=0 V
5
—
25
µA
IOmaxLL
DRV<1:0>=LL
0.1
0.5
0.8
mA
IOmaxLH
DRV<1:0>=LH
0.9
2.3
3.5
mA
IOmaxHL
DRV<1:0>=HL
1.5
3.1
4.8
mA
V
IOmaxHH
DRV<1:0>=HH
1.8
3.6
5.4
mA
Logic High Level Output
Voltage
VOH
IOH< IOmax source,
VDD=1.8 V
VDD – 0.6
—
—
V
Logic Low Level Output
Voltage
VOL
IOL< IOmax sink,
VDD=1.8 V
—
—
0.6
V
Note: All specifications guaranteed by qualification. Qualification test conditions are listed in the "Production Test
Conditions" section on page 73.
Rev. 1.3
71
Si1000/1/2/3/4/5
Table 4.23. Absolute Maximum Ratings
Parameter
Value
Unit
VDD to GND
–0.3, +3.6
V
Instantaneous VRF-peak to GND on TX Output Pin
–0.3, +8.0
V
Sustained VRF-peak to GND on TX Output Pin
–0.3, +6.5
V
Voltage on Digital Control Inputs
–0.3, VDD + 0.3
V
Voltage on Analog Inputs
–0.3, VDD + 0.3
V
+10
dBm
–40 to +85
C
Thermal Impedance JA
30
C/W
Junction Temperature TJ
+125
C
–55 to +125
C
RX Input Power
Operating Ambient Temperature Range TA
Storage Temperature Range TSTG
Note: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. These are stress ratings only and functional operation of the device at or beyond these ratings in the
operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Power Amplifier may be damaged if switched on without proper
load or termination connected. TX matching network design will influence TX VRF-peak on TX output pin.
Caution: ESD sensitive device.
72
Rev. 1.3
Si1000/1/2/3/4/5
4.4. Definition of Test Conditions for the EZRadioPRO Peripheral
Production Test Conditions:

TA = +25 °C

VDD = +3.3 VDC
Sensitivity measured at 919 MHz
 TX output power measured at 915 MHz
 External reference signal (XOUT) = 1.0 VPP at 30 MHz, centered around 0.8 VDC

Production test schematic (unless noted otherwise)
 All RF input and output levels referred to the pins of the Si100x (not the RF module)

Qualification Test Conditions:

TA = –40 to +85 °C

VDD = +1.8 to +3.6 VDC

Using 4432, 4431, or 4430 DKDB1 reference design or production test schematic
All RF input and output levels referred to the pins of the Si100x (not the RF module)

Rev. 1.3
73
Si1000/1/2/3/4/5
5. 10-Bit SAR ADC with 16-bit Auto-Averaging Accumulator and
Autonomous Low Power Burst Mode
The ADC0 on the Si1000/1/2/3/4/5 is a 300 ksps, 10-bit successive-approximation-register (SAR) ADC
with integrated track-and-hold and programmable window detector. ADC0 also has an autonomous low
power Burst Mode which can automatically enable ADC0, capture and accumulate samples, then place
ADC0 in a low power shutdown mode without CPU intervention. It also has a 16-bit accumulator that can
automatically oversample and average the ADC results.
The ADC is fully configurable under software control via Special Function Registers. The ADC0 operates in
Single-ended mode and may be configured to measure various different signals using the analog multiplexer described in “5.5. ADC0 Analog Multiplexer” on page 91. The voltage reference for the ADC is
selected as described in “5.7. Voltage and Ground Reference Options” on page 96.
VDD
From
AMUX0
Burst Mode Logic
10-bit
SAR
AIN+
ADC
AD0CM1
AD0CM2
AD0CM0
AD0BUSY (W )
001
Timer 0 Overflow
010
Timer 2 Overflow
011
Timer 3 Overflow
100
CNVSTR Input
REF
16-Bit Accumulator
SYSCLK
AD0TM
AMP0GN
AD08BE
AD0SC0
AD0SC1
AD0SC2
AD0SC3
AD0SC4
ADC0CF
000
ADC0L
ADC0PWR
Start
Conversion
ADC0LTH
ADC0H
ADC0TK
AD0WINT
AD0INT
AD0BUSY
AD0EN
BURSTEN
ADC0CN
AD0WINT
ADC0LTL
32
W indow
Compare
Logic
ADC0GTH ADC0GTL
Figure 5.1. ADC0 Functional Block Diagram
5.1. Output Code Formatting
The registers ADC0H and ADC0L contain the high and low bytes of the output conversion code from the
ADC at the completion of each conversion. Data can be right-justified or left-justified, depending on the
setting of the AD0SJST[2:0]. When the repeat count is set to 1, conversion codes are represented as 10bit unsigned integers. Inputs are measured from 0 to VREF x 1023/1024. Example codes are shown below
for both right-justified and left-justified data. Unused bits in the ADC0H and ADC0L registers are set to 0.
74
Rev. 1.3
Si1000/1/2/3/4/5
Input Voltage
Right-Justified ADC0H:ADC0L
(AD0SJST = 000)
Left-Justified ADC0H:ADC0L
(AD0SJST = 100)
VREF x 1023/1024
VREF x 512/1024
VREF x 256/1024
0
0x03FF
0x0200
0x0100
0x0000
0xFFC0
0x8000
0x4000
0x0000
When the repeat count is greater than 1, the output conversion code represents the accumulated result of
the conversions performed and is updated after the last conversion in the series is finished. Sets of 4, 8,
16, 32, or 64 consecutive samples can be accumulated and represented in unsigned integer format. The
repeat count can be selected using the AD0RPT bits in the ADC0AC register. When a repeat count higher
than 1, the ADC output must be right-justified (AD0SJST = 0xx); unused bits in the ADC0H and ADC0L
registers are set to 0. The example below shows the right-justified result for various input voltages and
repeat counts. Notice that accumulating 2n samples is equivalent to left-shifting by n bit positions when all
samples returned from the ADC have the same value.
Input Voltage
Repeat Count = 4
Repeat Count = 16
Repeat Count = 64
VREF x 1023/1024
VREF x 512/1024
VREF x 511/1024
0
0x0FFC
0x0800
0x07FC
0x0000
0x3FF0
0x2000
0x1FF0
0x0000
0xFFC0
0x8000
0x7FC0
0x0000
The AD0SJST bits can be used to format the contents of the 16-bit accumulator. The accumulated result
can be shifted right by 1, 2, or 3 bit positions. Based on the principles of oversampling and averaging, the
effective ADC resolution increases by 1 bit each time the oversampling rate is increased by a factor of 4.
The example below shows how to increase the effective ADC resolution by 1, 2, and 3 bits to obtain an
effective ADC resolution of 11-bit, 12-bit, or 13-bit respectively without CPU intervention.
Input Voltage
Repeat Count = 4
Shift Right = 1
11-Bit Result
Repeat Count = 16
Shift Right = 2
12-Bit Result
Repeat Count = 64
Shift Right = 3
13-Bit Result
VREF x 1023/1024
VREF x 512/1024
VREF x 511/1024
0
0x07F7
0x0400
0x03FE
0x0000
0x0FFC
0x0800
0x04FC
0x0000
0x1FF8
0x1000
0x0FF8
0x0000
Rev. 1.3
75
Si1000/1/2/3/4/5
5.2. Modes of Operation
ADC0 has a maximum conversion speed of 300 ksps. The ADC0 conversion clock (SARCLK) is a divided
version of the system clock when Burst Mode is disabled (BURSTEN = 0), or a divided version of the low
power oscillator when Burst Mode is enabled (BURSEN = 1). The clock divide value is determined by the
AD0SC bits in the ADC0CF register.
5.2.1. Starting a Conversion
A conversion can be initiated in one of five ways, depending on the programmed states of the ADC0 Start
of Conversion Mode bits (AD0CM2–0) in register ADC0CN. Conversions may be initiated by one of the following:
1. Writing a 1 to the AD0BUSY bit of register ADC0CN
2. A Timer 0 overflow (i.e., timed continuous conversions)
3. A Timer 2 overflow
4. A Timer 3 overflow
5. A rising edge on the CNVSTR input signal (pin P0.6)
Writing a 1 to AD0BUSY provides software control of ADC0 whereby conversions are performed "ondemand". During conversion, the AD0BUSY bit is set to logic 1 and reset to logic 0 when the conversion is
complete. The falling edge of AD0BUSY triggers an interrupt (when enabled) and sets the ADC0 interrupt
flag (AD0INT). Note: When polling for ADC conversion completions, the ADC0 interrupt flag (AD0INT)
should be used. Converted data is available in the ADC0 data registers, ADC0H:ADC0L, when bit AD0INT
is logic 1. Note that when Timer 2 or Timer 3 overflows are used as the conversion source, Low Byte overflows are used if Timer 2/3 is in 8-bit mode; High byte overflows are used if Timer 2/3 is in 16-bit mode.
See “27. Timers” on page 335 for timer configuration.
Important Note About Using CNVSTR: The CNVSTR input pin also functions as Port pin P0.6. When the
CNVSTR input is used as the ADC0 conversion source, Port pin P0.6 should be skipped by the Digital
Crossbar. To configure the Crossbar to skip P0.6, set to 1 Bit 6 in register P0SKIP. See “21. Port Input/Output” on page 210 for details on Port I/O configuration.
Important Note: When operating the device in one-cell mode, there is an option available to automatically
synchronize the start of conversion with the quietest portion of the dc-dc converter switching cycle. Activating this option may help to reduce interference from internal or external power supply noise generated by
the dc-dc converter. Asserting this bit will hold off the start of an ADC conversion initiated by any of the
methods described above until the ADC receives a synchronizing signal from the dc-dc converter. The
delay in initiation of the conversion can be as much as one cycle of the dc-dc converter clock, which is
625 ns at the minimum dc-dc clock frequency of 1.6 MHz. The synchronization feature also causes the dcdc converter clock to be used as the ADC0 conversion clock. The maximum conversion rate will be limited
to approximately 170 ksps at the maximum dc-dc converter clock rate of 3.2 MHz. In this mode, the ADC0
SAR Conversion Clock Divider must be set to 1 by setting AD0SC[4:0] = 00000b in SFR register ADC0CF.
To provide additional flexibility in minimizing noise, the ADC0 conversion clock provided by the dc-dc converter can be inverted by setting the AD0CKINV bit in the DC0CF register. For additional information on the
synchronization feature, see the description of the SYNC bit in “SFR Definition 16.1. DC0CN: DC-DC
Converter Control” on page 174 and the description of the AD0CKINV bit in “SFR Definition 16.2. DC0CF:
DC-DC Converter Configuration” on page 175. This bit must be set to 0 in two-cell mode for the ADC to
operate.
76
Rev. 1.3
Si1000/1/2/3/4/5
5.2.2. Tracking Modes
Each ADC0 conversion must be preceded by a minimum tracking time in order for the converted result to
be accurate. The minimum tracking time is given in Table 4.9. The AD0TM bit in register ADC0CN controls
the ADC0 track-and-hold mode. In its default state when Burst Mode is disabled, the ADC0 input is continuously tracked, except when a conversion is in progress. When the AD0TM bit is logic 1, ADC0 operates in
low-power track-and-hold mode. In this mode, each conversion is preceded by a tracking period of 3 SAR
clocks (after the start-of-conversion signal). When the CNVSTR signal is used to initiate conversions in
low-power tracking mode, ADC0 tracks only when CNVSTR is low; conversion begins on the rising edge of
CNVSTR (see Figure 5.2). Tracking can also be disabled (shutdown) when the device is in low power
standby or sleep modes. Low-power track-and-hold mode is also useful when AMUX settings are frequently changed, due to the settling time requirements described in “5.2.4. Settling Time Requirements” on
page 80.
A. ADC0 Timing for External Trigger Source
CNVSTR
(AD0CM[2:0]=100)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
SAR Clocks
AD0TM=1
AD0TM=0
Write '1' to AD0BUSY,
Timer 0, Timer 2,
Timer 1, Timer 3 Overflow
(AD0CM[2:0]=000, 001,010
011, 101)
Low Power
or Convert
Track or Convert
Low Power
Mode
Convert
Track
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Low Power
Track
or Convert
Convert
Low Power Mode
1 2 3 4 5 6 7 8 9 10 11 12 13 14
SAR
Clocks
AD0TM=0
Convert
B. ADC0 Timing for Internal Trigger Source
SAR
Clocks
AD0TM=1
Track
Track or
Convert
Convert
Track
Figure 5.2. 10-Bit ADC Track and Conversion Example Timing (BURSTEN = 0)
Rev. 1.3
77
Si1000/1/2/3/4/5
5.2.3. Burst Mode
Burst Mode is a power saving feature that allows ADC0 to remain in a low power state between conversions. When Burst Mode is enabled, ADC0 wakes from a low power state, accumulates 1, 4, 8, 16, 32, or
64 using an internal Burst Mode clock (approximately 20 MHz), then re-enters a low power state. Since the
Burst Mode clock is independent of the system clock, ADC0 can perform multiple conversions then enter a
low power state within a single system clock cycle, even if the system clock is slow (e.g. 32.768 kHz), or
suspended.
Burst Mode is enabled by setting BURSTEN to logic 1. When in Burst Mode, AD0EN controls the ADC0
idle power state (i.e., the state ADC0 enters when not tracking or performing conversions). If AD0EN is set
to logic 0, ADC0 is powered down after each burst. If AD0EN is set to logic 1, ADC0 remains enabled after
each burst. On each convert start signal, ADC0 is awakened from its Idle Power State. If ADC0 is powered
down, it will automatically power up and wait the programmable Power-Up Time controlled by the
AD0PWR bits. Otherwise, ADC0 will start tracking and converting immediately. Figure 5.3 shows an example of Burst Mode Operation with a slow system clock and a repeat count of 4.
When Burst Mode is enabled, a single convert start will initiate a number of conversions equal to the repeat
count. When Burst Mode is disabled, a convert start is required to initiate each conversion. In both modes,
the ADC0 End of Conversion Interrupt Flag (AD0INT) will be set after “repeat count” conversions have
been accumulated. Similarly, the Window Comparator will not compare the result to the greater-than and
less-than registers until “repeat count” conversions have been accumulated.
In Burst Mode, tracking is determined by the settings in AD0PWR and AD0TK. The default settings for
these registers will work in most applications without modification; however, settling time requirements may
need adjustment in some applications. Refer to “5.2.4. Settling Time Requirements” on page 80 for more
details.
Notes:
 Setting AD0TM to 1 will insert an additional 3 SAR clocks of tracking before each conversion,
regardless of the settings of AD0PWR and AD0TK.
 When using Burst Mode, care must be taken to issue a convert start signal no faster than once every
four SYSCLK periods. This includes external convert start signals.
 A rising edge of external start-of-conversion (CNVSTR) will cause only one ADC conversion in Burst
Mode, regardless of the value of the Repeat Count field. The end-of-conversion interrupt will occur after
the number of conversions specified in Repeat Count have completed. In other words, if Repeat Count
is set to 4, four pulses on CNVSTR will cause an ADC end-of-conversion interrupt. Refer to the bottom
portion of Figure 5.3, “Burst Mode Tracking Example with Repeat Count Set to 4,” on page 79 for an
example.
 To start multiple conversions in Burst Mode with one external start-of-conversion signal, the external
interrupts (/INT0 or /INT1) or Port Match can be used to trigger an ISR that writes to AD0BUSY.
External interrupts are configurable to be active low or active high, edge or level sensitive, but is only
avail-able on a limited number of pins. Port Match is only level sensitive, but is available on more port
pins than the external interrupts. Refer to section “12.6. External Interrupts INT0 and INT1” on
page 140 for details on external interrupts and section “21.4. Port Match” on page 219 for details on
Port Match.
78
Rev. 1.3
Si1000/1/2/3/4/5
System Clock
Convert Start
(AD0BUSY or Timer
Overflow)
Post-Tracking
AD0TM = 01
AD0EN = 0
Powered
Down
Power-Up
and Idle
T C T C T C T C
Powered
Down
Power-Up
and Idle
T C..
Dual-Tracking
AD0TM = 11
AD0EN = 0
Powered
Down
Power-Up
and Track
T C T C T C T C
Powered
Down
Power-Up
and Track
T C..
AD0PWR
Post-Tracking
AD0TM = 01
AD0EN = 1
Idle
T C T C T C T C
Idle
T C T C T C..
Dual-Tracking
AD0TM = 11
AD0EN = 1
Track
T C T C T C T C
Track
T C T C T C..
T = Tracking
C = Converting
Convert Start
(CNVSTR)
Post-Tracking
AD0TM = 01
AD0EN = 0
Powered
Down
Power-Up
and Idle
T C
Powered
Down
Power-Up
and Idle
T C..
Dual-Tracking
AD0TM = 11
AD0EN = 0
Powered
Down
Power-Up
and Track
T C
Powered
Down
Power-Up
and Track
T C..
AD0PWR
Post-Tracking
AD0TM = 01
AD0EN = 1
Idle
T C
Idle
T C
Idle..
Dual-Tracking
AD0TM = 11
AD0EN = 1
Track
T C
Track
T C
Track..
T = Tracking
C = Converting
Figure 5.3. Burst Mode Tracking Example with Repeat Count Set to 4
Rev. 1.3
79
Si1000/1/2/3/4/5
5.2.4. Settling Time Requirements
A minimum amount of tracking time is required before each conversion can be performed, to allow the
sampling capacitor voltage to settle. This tracking time is determined by the AMUX0 resistance, the ADC0
sampling capacitance, any external source resistance, and the accuracy required for the conversion. Note
that in low-power tracking mode, three SAR clocks are used for tracking at the start of every conversion.
For many applications, these three SAR clocks will meet the minimum tracking time requirements, and
higher values for the external source impedance will increase the required tracking time.
Figure 5.4 shows the equivalent ADC0 input circuit. The required ADC0 settling time for a given settling
accuracy (SA) may be approximated by Equation 5.1. When measuring the Temperature Sensor output or
VDD with respect to GND, RTOTAL reduces to RMUX. See Table 4.9 for ADC0 minimum settling time requirements as well as the mux impedance and sampling capacitor values.
n
2
t = ln  -------  R TOTAL C SAMPLE
 SA
Equation 5.1. ADC0 Settling Time Requirements
Where:
SA is the settling accuracy, given as a fraction of an LSB (for example, 0.25 to settle within 1/4 LSB)
t is the required settling time in seconds
RTOTAL is the sum of the AMUX0 resistance and any external source resistance.
n is the ADC resolution in bits (10).
MUX Select
P0.x
R MUX
C SAMPLE
RCInput= R MUX * C SAMPLE
Note: The value of CSAMPLE depends on the PGA Gain. See Table 4.9 for details.
Figure 5.4. ADC0 Equivalent Input Circuits
80
Rev. 1.3
Si1000/1/2/3/4/5
5.2.5. Gain Setting
The ADC has gain settings of 1x and 0.5x. In 1x mode, the full scale reading of the ADC is determined
directly by VREF. In 0.5x mode, the full-scale reading of the ADC occurs when the input voltage is VREF x 2.
The 0.5x gain setting can be useful to obtain a higher input Voltage range when using a small VREF voltage, or to measure input voltages that are between VREF and VDD. Gain settings for the ADC are controlled by the AMP0GN bit in register ADC0CF.
5.3. 8-Bit Mode
Setting the ADC08BE bit in register ADC0CF to 1 will put the ADC in 8-bit mode.In 8-bit mode, only the
8 MSBs of data are converted, allowing the conversion to be completed in two fewer SAR clock cycles
than a 10-bit conversion. This can result in an overall lower power consumption since the system can
spend more time in a low power mode. The two LSBs of a conversion are always 00 in this mode, and the
ADC0L register will always read back 0x00.
Rev. 1.3
81
Si1000/1/2/3/4/5
SFR Definition 5.1. ADC0CN: ADC0 Control
Bit
7
6
5
4
Name
AD0EN
BURSTEN
AD0INT
Type
R/W
R/W
R/W
W
R/W
Reset
0
0
0
0
0
AD0EN
2
AD0BUSY AD0WINT
SFR Page = 0x0; SFR Address = 0xE8; bit-addressable;
Bit
Name
7
3
1
0
ADC0CM
R/W
0
0
0
Function
ADC0 Enable.
0: ADC0 Disabled (low-power shutdown).
1: ADC0 Enabled (active and ready for data conversions).
6
BURSTEN
ADC0 Burst Mode Enable.
0: ADC0 Burst Mode Disabled.
1: ADC0 Burst Mode Enabled.
5
AD0INT
ADC0 Conversion Complete Interrupt Flag.
Set by hardware upon completion of a data conversion (BURSTEN=0), or a burst
of conversions (BURSTEN=1). Can trigger an interrupt. Must be cleared by software.
4
AD0BUSY
ADC0 Busy.
Writing 1 to this bit initiates an ADC conversion when ADC0CM[2:0] = 000.
3
AD0WINT
ADC0 Window Compare Interrupt Flag.
Set by hardware when the contents of ADC0H:ADC0L fall within the window specified by ADC0GTH:ADC0GTL and ADC0LTH:ADC0LTL. Can trigger an interrupt.
Must be cleared by software.
2:0
ADC0CM[2:0] ADC0 Start of Conversion Mode Select.
Specifies the ADC0 start of conversion source.
000: ADC0 conversion initiated on write of 1 to AD0BUSY.
001: ADC0 conversion initiated on overflow of Timer 0.
010: ADC0 conversion initiated on overflow of Timer 2.
011: ADC0 conversion initiated on overflow of Timer 3.
1xx: ADC0 conversion initiated on rising edge of CNVSTR.
82
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 5.2. ADC0CF: ADC0 Configuration
Bit
7
6
5
4
3
2
1
0
Name
AD0SC[4:0]
AD08BE
AD0TM
AMP0GN
Type
R/W
R/W
R/W
R/W
0
0
0
Reset
1
1
1
1
SFR Page = 0x0; SFR Address = 0xBC
Bit
Name
7:3
1
Function
AD0SC[4:0] ADC0 SAR Conversion Clock Divider.
SAR Conversion clock is derived from FCLK by the following equation, where
AD0SC refers to the 5-bit value held in bits AD0SC[4:0]. SAR Conversion clock
requirements are given in Table 4.9.
BURSTEN = 0: FCLK is the current system clock.
BURSTEN = 1: FCLK is the 20 MHz low power oscillator, independent of the system
clock.
FCLK
AD0SC = -------------------- – 1 *
CLK SAR
*Round the result up.
or
FCLK
CLK SAR = ---------------------------AD0SC + 1
2
AD08BE
ADC0 8-Bit Mode Enable.
0: ADC0 operates in 10-bit mode (normal operation).
1: ADC0 operates in 8-bit mode.
1
AD0TM
ADC0 Track Mode.
Selects between Normal or Delayed Tracking Modes.
0: Normal Track Mode: When ADC0 is enabled, conversion begins immediately following the start-of-conversion signal.
1: Delayed Track Mode: When ADC0 is enabled, conversion begins 3 SAR clock
cycles following the start-of-conversion signal. The ADC is allowed to track during
this time.
0
AMP0GN
ADC0 Gain Control.
0: The on-chip PGA gain is 0.5.
1: The on-chip PGA gain is 1.
Rev. 1.3
83
Si1000/1/2/3/4/5
SFR Definition 5.3. ADC0AC: ADC0 Accumulator Configuration
Bit
7
6
5
4
Name
Reserved
AD0AE
AD0SJST
AD0RPT
Type
R/W
W
R/W
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xBA
Bit
Name
7
6
Reserved
AD0AE
3
0
2
0
1
0
0
0
Function
Read = 0b.
ADC0 Accumulate Enable.
Enables multiple conversions to be accumulated when burst mode is disabled.
0: ADC0H:ADC0L contain the result of the latest conversion when Burst Mode is
disabled.
1: ADC0H:ADC0L contain the accumulated conversion results when Burst Mode
is disabled. Software must write 0x0000 to ADC0H:ADC0L to clear the accumulated result.
This bit is write-only. Always reads 0b.
5:3
AD0SJST[2:0] ADC0 Accumulator Shift and Justify.
Specifies the format of data read from ADC0H:ADC0L.
000: Right justified. No shifting applied.
001: Right justified. Shifted right by 1 bit.
010: Right justified. Shifted right by 2 bits.
011: Right justified. Shifted right by 3 bits.
100: Left justified. No shifting applied.
All remaining bit combinations are reserved.
2:0
AD0RPT[2:0] ADC0 Repeat Count.
Selects the number of conversions to perform and accumulate in Burst Mode.
This bit field must be set to 000 if Burst Mode is disabled.
000: Perform and Accumulate 1 conversion.
001: Perform and Accumulate 4 conversions.
010: Perform and Accumulate 8 conversions.
011: Perform and Accumulate 16 conversions.
100: Perform and Accumulate 32 conversions.
101: Perform and Accumulate 64 conversions.
All remaining bit combinations are reserved.
84
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 5.4. ADC0PWR: ADC0 Burst Mode Power-Up Time
Bit
7
6
5
4
Name
Reserved
Type
R
R
R
R
Reset
0
0
0
0
2
1
0
AD0PWR[3:0]
SFR Page = 0xF; SFR Address = 0xBA
Bit
Name
7
6:4
3:0
3
R/W
1
1
1
1
Function
Reserved
Read = 0b; Must write 0b.
Unused
Read = 0000b; Write = Don’t Care.
AD0PWR[3:0] ADC0 Burst Mode Power-Up Time.
Sets the time delay required for ADC0 to power up from a low power state.
For BURSTEN = 0:
ADC0 power state controlled by AD0EN.
For BURSTEN = 1 and AD0EN = 1:
ADC0 remains enabled and does not enter a low power state after all conversions are complete.
Conversions can begin immediately following the start-of-conversion signal.
For BURSTEN = 1 and AD0EN = 0:
ADC0 enters a low power state (as specified in Table 5.1) after all conversions
are complete. 
Conversions can begin a programmed delay after the start-of-conversion signal.
The ADC0 Burst Mode Power-Up time is programmed according to the following equation:
Tstartup
AD0PWR = ---------------------- – 1
400ns
or
Tstartup =  AD0PWR + 1 400ns
Rev. 1.3
85
Si1000/1/2/3/4/5
SFR Definition 5.5. ADC0TK: ADC0 Burst Mode Track Time
Bit
7
6
5
4
2
1
0
1
0
AD0TK[5:0]
Name
Type
R
R
Reset
0
0
R/W
0
1
SFR Page = 0xF; SFR Address = 0xBD
Bit
Name
7:6
5:0
3
0
1
Function
Unused
Read = 00b; Write = Don’t Care.
AD0TK[5:0] ADC0 Burst Mode Track Time.
Sets the time delay between consecutive conversions performed in Burst Mode.
The ADC0 Burst Mode Track time is programmed according to the following equation:
Ttrack
AD0TK = 63 –  ----------------- – 1
50ns
or
Ttrack =  64 – AD0TK 50ns
Notes:
1. If AD0TM is set to 1, an additional 3 SAR clock cycles of Track time will be inserted prior to starting the
conversion.
2. The Burst Mode Track delay is not inserted prior to the first conversion. The required tracking time for the first
conversion should be met by the Burst Mode Power-Up Time.
86
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 5.6. ADC0H: ADC0 Data Word High Byte
Bit
7
6
5
4
3
Name
ADC0[15:8]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xBE
Bit
Name
Description
7:0
ADC0[15:8] ADC0 Data Word High
Byte.
2
1
0
0
0
0
Read
Write
Most Significant Byte of the
16-bit ADC0 Accumulator
formatted according to the
settings in AD0SJST[2:0].
Set the most significant
byte of the 16-bit ADC0
Accumulator to the value
written.
Note: If Accumulator shifting is enabled, the most significant bits of the value read will be zeros. This register
should not be written when the SYNC bit is set to 1.
SFR Definition 5.7. ADC0L: ADC0 Data Word Low Byte
Bit
7
6
5
4
Name
ADC0[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xBD;
Bit
Name
Description
7:0
ADC0[7:0]
ADC0 Data Word Low Byte.
3
2
1
0
0
0
0
0
Read
Write
Least Significant Byte of the
16-bit ADC0 Accumulator
formatted according to the
settings in AD0SJST[2:0].
Set the least significant
byte of the 16-bit ADC0
Accumulator to the value
written.
Note: If Accumulator shifting is enabled, the most significant bits of the value read will be the least significant bits of
the accumulator high byte. This register should not be written when the SYNC bit is set to 1.
Rev. 1.3
87
Si1000/1/2/3/4/5
5.4. Programmable Window Detector
The ADC Programmable Window Detector continuously compares the ADC0 output registers to user-programmed limits, and notifies the system when a desired condition is detected. This is especially effective in
an interrupt-driven system, saving code space and CPU bandwidth while delivering faster system
response times. The window detector interrupt flag (AD0WINT in register ADC0CN) can also be used in
polled mode. The ADC0 Greater-Than (ADC0GTH, ADC0GTL) and Less-Than (ADC0LTH, ADC0LTL)
registers hold the comparison values. The window detector flag can be programmed to indicate when measured data is inside or outside of the user-programmed limits, depending on the contents of the ADC0
Less-Than and ADC0 Greater-Than registers.
SFR Definition 5.8. ADC0GTH: ADC0 Greater-Than High Byte
Bit
7
6
5
4
3
Name
AD0GT[15:8]
Type
R/W
Reset
1
1
1
1
1
SFR Page = 0x0; SFR Address = 0xC4
Bit
Name
7:0
2
1
0
1
1
1
Function
AD0GT[15:8] ADC0 Greater-Than High Byte.
Most Significant Byte of the 16-bit Greater-Than window compare register.
SFR Definition 5.9. ADC0GTL: ADC0 Greater-Than Low Byte
Bit
7
6
5
4
3
Name
AD0GT[7:0]
Type
R/W
Reset
1
1
1
1
SFR Page = 0x0; SFR Address = 0xC3
Bit
Name
7:0
1
2
1
0
1
1
1
Function
AD0GT[7:0] ADC0 Greater-Than Low Byte.
Least Significant Byte of the 16-bit Greater-Than window compare register.
Note: In 8-bit mode, this register should be set to 0x00.
88
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 5.10. ADC0LTH: ADC0 Less-Than High Byte
Bit
7
6
5
4
3
Name
AD0LT[15:8]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xC6
Bit
Name
7:0
2
1
0
0
0
0
Function
AD0LT[15:8] ADC0 Less-Than High Byte.
Most Significant Byte of the 16-bit Less-Than window compare register.
SFR Definition 5.11. ADC0LTL: ADC0 Less-Than Low Byte
Bit
7
6
5
4
3
Name
AD0LT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xC5
Bit
Name
7:0
0
2
1
0
0
0
0
Function
AD0LT[7:0] ADC0 Less-Than Low Byte.
Least Significant Byte of the 16-bit Less-Than window compare register.
Note: In 8-bit mode, this register should be set to 0x00.
5.4.1. Window Detector In Single-Ended Mode
Figure 5.5
shows
two
example
window
comparisons
for
right-justified
data,
with
ADC0LTH:ADC0LTL = 0x0080 (128d) and ADC0GTH:ADC0GTL = 0x0040 (64d). The input voltage can
range from 0 to VREF x (1023/1024) with respect to GND, and is represented by a 10-bit unsigned integer
value. In the left example, an AD0WINT interrupt will be generated if the ADC0 conversion word
(ADC0H:ADC0L) is within the range defined by ADC0GTH:ADC0GTL and ADC0LTH:ADC0LTL
(if 0x0040 < ADC0H:ADC0L < 0x0080). In the right example, and AD0WINT interrupt will be generated if
the ADC0 conversion word is outside of the range defined by the ADC0GT and ADC0LT registers
(if ADC0H:ADC0L < 0x0040 or ADC0H:ADC0L > 0x0080). Figure 5.6 shows an example using left-justified data with the same comparison values.
Rev. 1.3
89
Si1000/1/2/3/4/5
ADC0H:ADC0L
ADC0H:ADC0L
Input Voltage
(Px.x - GND)
VREF x (1023/1024)
Input Voltage
(Px.x - GND)
0x03FF
VREF x (1023/1024)
0x03FF
AD0WINT
not affected
AD0WINT=1
0x0081
VREF x (128/1024)
0x0080
0x0081
ADC0LTH:ADC0LTL
VREF x (128/1024)
0x007F
0x0080
0x007F
AD0WINT=1
VREF x (64/1024)
0x0041
0x0040
ADC0GTH:ADC0GTL
VREF x (64/1024)
0x003F
0x0041
0x0040
ADC0GTH:ADC0GTL
AD0WINT
not affected
ADC0LTH:ADC0LTL
0x003F
AD0WINT=1
AD0WINT
not affected
0
0x0000
0
0x0000
Figure 5.5. ADC Window Compare Example: Right-Justified Single-Ended Data
ADC0H:ADC0L
ADC0H:ADC0L
Input Voltage
(Px.x - GND)
VREF x (1023/1024)
Input Voltage
(Px.x - GND)
0xFFC0
VREF x (1023/1024)
0xFFC0
AD0WINT
not affected
AD0WINT=1
0x2040
VREF x (128/1024)
0x2000
0x2040
ADC0LTH:ADC0LTL
VREF x (128/1024)
0x1FC0
0x2000
0x1FC0
AD0WINT=1
0x1040
VREF x (64/1024)
0x1000
0x1040
ADC0GTH:ADC0GTL
VREF x (64/1024)
0x0FC0
0x1000
ADC0GTH:ADC0GTL
AD0WINT
not affected
ADC0LTH:ADC0LTL
0x0FC0
AD0WINT=1
AD0WINT
not affected
0
0x0000
0
0x0000
Figure 5.6. ADC Window Compare Example: Left-Justified Single-Ended Data
5.4.2. ADC0 Specifications
See “4. Electrical Characteristics” on page 40 for a detailed listing of ADC0 specifications.
90
Rev. 1.3
Si1000/1/2/3/4/5
5.5. ADC0 Analog Multiplexer
ADC0 on Si1000/1/2/3/4/5 has an analog multiplexer, referred to as AMUX0.
AMUX0 selects the positive inputs to the single-ended ADC0. Any of the following may be selected as the
positive input: Port I/O pins, the on-chip temperature sensor, Regulated Digital Supply Voltage (Output of
VREG0), VDD_MCU Supply, or the positive input may be connected to GND. The ADC0 input channels
are selected in the ADC0MX register described in SFR Definition 5.12.
AD0MX4
AD0MX3
AD0MX2
AD0MX1
AM0MX0
ADC0MX
P0.0
Programmable
Attenuator
AIN+
P2.6*
AMUX
Temp
Sensor
ADC0
Gain = 0. 5 or 1
Digital Supply
VDD_MCU
*P1.0 – P1.4 are not available as device pins.
P2.4 – P2.6 are only available on Si1000/1/2/3 devices
Figure 5.7. ADC0 Multiplexer Block Diagram
Important Note About ADC0 Input Configuration: Port pins selected as ADC0 inputs should be configured as analog inputs, and should be skipped by the Digital Crossbar. To configure a Port pin for analog
input, set to 0 the corresponding bit in register PnMDIN and disable the digital driver (PnMDOUT = 0 and
Port Latch = 1). To force the Crossbar to skip a Port pin, set to 1 the corresponding bit in register PnSKIP.
See Section “21. Port Input/Output” on page 210 for more Port I/O configuration details.
Rev. 1.3
91
Si1000/1/2/3/4/5
SFR Definition 5.12. ADC0MX: ADC0 Input Channel Select
Bit
7
6
5
4
3
2
1
0
AD0MX
Name
Type
R
R
R
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
1
1
1
1
1
SFR Page = 0x0; SFR Address = 0xBB
Bit
Name
7:5
4:0
Unused
AD0MX
Function
Read = 000b; Write = Don’t Care.
AMUX0 Positive Input Selection.
Selects the positive input channel for ADC0.
00000:
00001:
00010:
00011:
00100:
00101:
00110:
00111:
01000:
01001:
01010:
01011:
01100:
01101:
01110:
01111:
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
Reserved.
Reserved.
Reserved.
Reserved.
Reserved.
P1.5
P1.6
P1.7
10000:
10001:
10010:
10011:
10100:
10101:
10110:
10111:
11000:
11001:
11010:
11011:
11100:
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
Reserved.
Reserved.
Reserved.
Reserved.
Temperature Sensor*
VDD_MCU Supply Voltage
(1.8–3.6 V)
11101:
Digital Supply Voltage
(VREG0 Output, 1.7 V Typical)
11110:
VDD_MCU Supply Voltage
(1.8–3.6 V)
Ground
11111:
*Note: Before switching the ADC multiplexer from another channel to the temperature sensor, the ADC mux should
select the “Ground” channel as an intermediate step. The intermediate “Ground” channel selection step will
discharge any voltage on the ADC sampling capacitor from the previous channel selection. This will prevent
the possibility of a high voltage (> 2 V) being presented to the temperature sensor circuit, which can otherwise
impact its long-term reliability.
92
Rev. 1.3
Si1000/1/2/3/4/5
5.6. Temperature Sensor
An on-chip temperature sensor is included on the Si1000/1/2/3/4/5 which can be directly accessed via the
ADC multiplexer in single-ended configuration. To use the ADC to measure the temperature sensor, the
ADC mux channel should select the temperature sensor. The temperature sensor transfer function is
shown in Figure 5.8. The output voltage (VTEMP) is the positive ADC input when the ADC multiplexer is set
correctly. The TEMPE bit in register REF0CN enables/disables the temperature sensor, as described in
SFR Definition 5.15. While disabled, the temperature sensor defaults to a high impedance state and any
ADC measurements performed on the sensor will result in meaningless data. Refer to Table 4.9 for the
slope and offset parameters of the temperature sensor.
Note: Before switching the ADC multiplexer from another channel to the temperature sensor, the ADC mux should
select the “Ground” channel as an intermediate step. The intermediate “Ground” channel selection step will
discharge any voltage on the ADC sampling capacitor from the previous channel selection. This will prevent the
possibility of a high voltage (> 2 V) being presented to the temperature sensor circuit, which can otherwise
impact its long-term reliability.
V TEMP = Slope x (Temp C - 25) + Offset
TempC = 25 + (V TEMP - Offset) / Slope
Voltage
Slope ( V / deg C)
Offset ( V at 25 Celsius)
Temperature
Figure 5.8. Temperature Sensor Transfer Function
5.6.1. Calibration
The uncalibrated temperature sensor output is extremely linear and suitable for relative temperature measurements (see Table 4.10 for linearity specifications). For absolute temperature measurements, offset
and/or gain calibration is recommended. Typically a 1-point (offset) calibration includes the following steps:
1. Control/measure the ambient temperature (this temperature must be known).
2. Power the device, and delay for a few seconds to allow for self-heating.
3. Perform an ADC conversion with the temperature sensor selected as the positive input and GND
Rev. 1.3
93
Si1000/1/2/3/4/5
selected as the negative input.
4. Calculate the offset characteristics, and store this value in non-volatile memory for use with subsequent
temperature sensor measurements.
Figure 5.9 shows the typical temperature sensor error assuming a 1-point calibration at 25 °C. Parameters that affect ADC measurement, in particular the voltage reference value, will also affect temperature measurement.
Error (degrees C)
A single-point offset measurement of the temperature sensor is performed on each device during production test. The measurement is performed at 25 °C ±5 °C, using the ADC with the internal high speed reference buffer selected as the Voltage Reference. The direct ADC result of the measurement is stored in the
SFR registers TOFFH and TOFFL, shown in SFR Definition 5.13 and SFR Definition 5.14.
5.00
5.00
4.00
4.00
3.00
3.00
2.00
2.00
1.00
1.00
0.00
-40.00
-20.00
0.00
40.00
20.00
60.00
80.00
0.00
-1.00
-1.00
-2.00
-2.00
-3.00
-3.00
-4.00
-4.00
-5.00
-5.00
Temperature (degrees C)
Figure 5.9. Temperature Sensor Error with 1-Point Calibration (VREF = 1.68 V)
94
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 5.13. TOFFH: ADC0 Data Word High Byte
Bit
7
6
5
4
3
2
1
0
TOFF[9:2]
Name
Type
R
R
R
R
R
R
R
R
Reset
Varies
Varies
Varies
Varies
Varies
Varies
Varies
Varies
SFR Page = 0xF; SFR Address = 0x86
Bit
Name
7:0
TOFF[9:2]
Function
Temperature Sensor Offset High Bits.
Most Significant Bits of the 10-bit temperature sensor offset measurement.
SFR Definition 5.14. TOFFL: ADC0 Data Word Low Byte
Bit
7
6
5
4
3
2
1
0
0
0
0
0
0
0
TOFF[1:0]
Name
Type
R
R
Reset
Varies
Varies
SFR Page = 0xF; SFR Address = 0x85
Bit
Name
7:6
TOFF[1:0]
Function
Temperature Sensor Offset Low Bits.
Least Significant Bits of the 10-bit temperature sensor offset measurement.
5:0
Unused
Read = 0; Write = Don't Care.
Rev. 1.3
95
Si1000/1/2/3/4/5
5.7. Voltage and Ground Reference Options
The voltage reference MUX is configurable to use an externally connected voltage reference, one of two
internal voltage references, or one of two power supply voltages (see Figure 5.10). The ground reference
MUX allows the ground reference for ADC0 to be selected between the ground pin (GND) or a port pin
dedicated to analog ground (P0.1/AGND).
The voltage and ground reference options are configured using the REF0CN SFR described on page 98.
Electrical specifications are can be found in the Electrical Specifications Chapter.
Important Note About the VREF and AGND Inputs: Port pins are used as the external VREF and AGND
inputs. When using an external voltage reference or the internal precision reference, P0.0/VREF should be
configured as an analog input and skipped by the Digital Crossbar. When using AGND as the ground reference to ADC0, P0.1/AGND should be configured as an analog input and skipped by the Digital Crossbar.
Refer to Section “21. Port Input/Output” on page 210 for complete Port I/O configuration details. The external reference voltage must be within the range 0  VREF  VDD_MCU and the external ground reference
must be at the same DC voltage potential as GND.
REFOE
REFGND
REFSL1
REFSL0
TEMPE
R E F 0C N
T em p S ensor
EN
ADC
Input
M ux
REFOE
EN
VDD
R1
E xternal
V oltage
R eference
C ircuit
Internal 1.68V
R eference
P 0 .0/V R E F
00
V D D /D C +
01
Internal 1.8V
R egulated D igital S upply
GND
10
VREF
(to A D C )
11
4 .7 F
+
0 .1 F
R ecom m ended
B ypass C apacitors
Internal 1.65 V
H igh S peed R eference
GND
0
P 0.1/A G N D
1
REFGND
Figure 5.10. Voltage Reference Functional Block Diagram
96
Rev. 1.3
G round
(to A D C )
Si1000/1/2/3/4/5
5.8. External Voltage References
To use an external voltage reference, REFSL[1:0] should be set to 00 and the internal 1.68 V precision reference should be disabled by setting REFOE to 0. Bypass capacitors should be added as recommended
by the manufacturer of the external voltage reference.
5.9. Internal Voltage References
For applications requiring the maximum number of port I/O pins, or very short VREF turn-on time, the
1.65 V high-speed reference will be the best internal reference option to choose. The high speed internal
reference is selected by setting REFSL[1:0] to 11. When selected, the high speed internal reference will be
automatically enabled/disabled on an as-needed basis by ADC0.
For applications requiring the highest absolute accuracy, the 1.68 V precision voltage reference will be the
best internal reference option to choose. The 1.68 V precision reference may be enabled and selected by
setting REFOE to 1 and REFSL[1:0] to 00. An external capacitor of at least 0.1 µF is recommended when
using the precision voltage reference.
In applications that leave the precision internal oscillator always running, there is no additional power
required to use the precision voltage reference. In all other applications, using the high speed reference
will result in lower overall power consumption due to its minimal startup time and the fact that it remains in
a low power state when an ADC conversion is not taking place.
Note: When using the precision internal oscillator as the system clock source, the precision voltage reference should not be enabled from a disabled state. To use the precision oscillator and the precision voltage
reference simultaneously, the precision voltage reference should be enabled first and allowed to settle to
its final value (charging the external capacitor) before the precision oscillator is started and selected as the
system clock.
For applications with a non-varying power supply voltage, using the power supply as the voltage reference
can provide ADC0 with added dynamic range at the cost of reduced power supply noise rejection. To use
the 1.8 to 3.6 V power supply voltage (VDD_MCU) or the 1.8 V regulated digital supply voltage as the reference source, REFSL[1:0] should be set to 01 or 10, respectively.
5.10. Analog Ground Reference
To prevent ground noise generated by switching digital logic from affecting sensitive analog measurements, a separate analog ground reference option is available. When enabled, the ground reference for
ADC0 during both the tracking/sampling and the conversion periods is taken from the P0.1/AGND pin. Any
external sensors sampled by ADC0 should be referenced to the P0.1/AGND pin. This pin should be connected to the ground terminal of any external sensors sampled by ADC0. If an external voltage reference is
used, the P0.1/AGND pin should be connected to the ground of the external reference and its associated
decoupling capacitor. If the 1.68 V precision internal reference is used, then P0.1/AGND should be connected to the ground terminal of its external decoupling capacitor. The separate analog ground reference
option is enabled by setting REFGND to 1. Note that when sampling the internal temperature sensor, the
internal chip ground is always used for the sampling operation, regardless of the setting of the REFGND
bit. Similarly, whenever the internal 1.65 V high-speed reference is selected, the internal chip ground is
always used during the conversion period, regardless of the setting of the REFGND bit.
5.11. Temperature Sensor Enable
The TEMPE bit in register REF0CN enables/disables the temperature sensor. While disabled, the temperature sensor defaults to a high impedance state and any ADC0 measurements performed on the sensor result in meaningless data. See Section “5.6. Temperature Sensor” on page 93 for details on
temperature sensor characteristics when it is enabled.
Rev. 1.3
97
Si1000/1/2/3/4/5
SFR Definition 5.15. REF0CN: Voltage Reference Control
Bit
7
6
5
4
REFGND
Name
3
REFSL
2
1
TEMPE
0
REFOE
Type
R
R
R/W
R/W
R/W
R/W
R
R/W
Reset
0
0
0
1
1
0
0
0
SFR Page = 0x0; SFR Address = 0xD1
Bit
Name
7:6
5
Unused
Function
Read = 00b; Write = Don’t Care.
REFGND Analog Ground Reference.
Selects the ADC0 ground reference.
0: The ADC0 ground reference is the GND pin.
1: The ADC0 ground reference is the P0.1/AGND pin.
4:3
REFSL
Voltage Reference Select.
Selects the ADC0 voltage reference.
00: The ADC0 voltage reference is the P0.0/VREF pin.
01: The ADC0 voltage reference is the VDD_MCU pin.
10: The ADC0 voltage reference is the internal 1.8 V digital supply voltage.
11: The ADC0 voltage reference is the internal 1.65 V high speed voltage reference.
2
TEMPE
Temperature Sensor Enable.
Enables/Disables the internal temperature sensor.
0: Temperature Sensor Disabled.
1: Temperature Sensor Enabled.
1
Unused
Read = 0b; Write = Don’t Care.
0
REFOE
Internal Voltage Reference Output Enable.
Connects/Disconnects the internal voltage reference to the P0.0/VREF pin.
0: Internal 1.68 V Precision Voltage Reference disabled and not connected to
P0.0/VREF.
1: Internal 1.68 V Precision Voltage Reference enabled and connected to
P0.0/VREF.
5.12. Voltage Reference Electrical Specifications
See Table 4.11 on page 60 for detailed Voltage Reference Electrical Specifications.
98
Rev. 1.3
Si1000/1/2/3/4/5
6. Programmable Current Reference (IREF0)
Si1000/1/2/3/4/5 devices include an on-chip programmable current reference (source or sink) with two output current settings: Low Power Mode and High Current Mode. The maximum current output in Low Power
Mode is 63 µA (1 µA steps) and the maximum current output in High Current Mode is 504 µA (8 µA steps).
The current source/sink is controlled though the IREF0CN special function register. It is enabled by setting
the desired output current to a non-zero value. It is disabled by writing 0x00 to IREF0CN. The port I/O pin
associated with ISRC0 should be configured as an analog input and skipped in the Crossbar. See Section
“21. Port Input/Output” on page 210 for more details.
SFR Definition 6.1. IREF0CN: Current Reference Control
Bit
7
6
5
Name
SINK
MODE
IREF0DAT
Type
R/W
R/W
R/W
Reset
0
0
0
4
0
SFR Page = 0x0; SFR Address = 0xB9
Bit
Name
7
SINK
3
0
2
1
0
0
0
0
Function
IREF0 Current Sink Enable.
Selects if IREF0 is a current source or a current sink.
0: IREF0 is a current source.
1: IREF0 is a current sink.
6
MDSEL
IREF0 Output Mode Select.
Selects Low Power or High Current Mode.
0: Low Power Mode is selected (step size = 1 µA).
1: High Current Mode is selected (step size = 8 µA).
5:0
IREF0DAT[5:0]
IREF0 Data Word.
Specifies the number of steps required to achieve the desired output current.
Output current = direction x step size x IREF0DAT.
IREF0 is in a low power state when IREF0DAT is set to 0x00.
6.1. IREF0 Specifications
See Table 4.12 on page 61 for a detailed listing of IREF0 specifications.
Rev. 1.3
99
Si1000/1/2/3/4/5
7. Comparators
Si1000/1/2/3/4/5 devices include two on-chip programmable voltage comparators: Comparator 0 (CPT0) is
shown in Figure 7.1; Comparator 1 (CPT1) is shown in Figure 7.2. The two comparators operate identically, but may differ in their ability to be used as reset or wake-up sources. See the Reset Sources chapter
and the Power Management chapter for details on reset sources and low power mode wake-up sources,
respectively.
The Comparator offers programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a synchronous “latched” output (CP0, CP1), or an
asynchronous “raw” output (CP0A, CP1A). The asynchronous CP0A signal is available even when the
system clock is not active. This allows the Comparator to operate and generate an output when the device
is in some low power modes.
7.1. Comparator Inputs
Each Comparator performs an analog comparison of the voltage levels at its positive (CP0+ or CP1+) and
negative (CP0- or CP1-) input. Both comparators support multiple port pin inputs multiplexed to their positive and negative comparator inputs using analog input multiplexers. The analog input multiplexers are
completely under software control and configured using SFR registers. See Section “7.6. Comparator0 and
Comparator1 Analog Multiplexers” on page 107 for details on how to select and configure Comparator
inputs.
Important Note About Comparator Inputs: The Port pins selected as Comparator inputs should be configured as analog inputs and skipped by the Crossbar. See the Port I/O chapter for more details on how to
configure Port I/O pins as Analog Inputs. The Comparator may also be used to compare the logic level of
digital signals, however, Port I/O pins configured as digital inputs must be driven to a valid logic state
(HIGH or LOW) to avoid increased power consumption.
CPT0CN
CP0EN
CP0OUT
CP0RIF
VDD
CP0FIF
CP0HYP1
CP0
Interrupt
CP0HYP0
CP0HYN1
CP0HYN0
CPT0MD
Analog Input Multiplexer
CP0FIE
CP0RIE
CP0MD1
CP0MD0
Px.x
CP0
Rising-edge
CP0 +
CP0
Falling-edge
Interrupt
Logic
Px.x
CP0
+
D
-
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Px.x
Crossbar
(SYNCHRONIZER)
CP0 -
GND
(ASYNCHRONOUS)
Px.x
Reset
Decision
Tree
Figure 7.1. Comparator 0 Functional Block Diagram
100
Rev. 1.3
CP0A
Si1000/1/2/3/4/5
7.2. Comparator Outputs
When a comparator is enabled, its output is a logic 1 if the voltage at the positive input is higher than the
voltage at the negative input. When disabled, the comparator output is a logic 0. The comparator output is
synchronized with the system clock as shown in Figure 7.2. The synchronous “latched” output (CP0, CP1)
can be polled in software (CPnOUT bit), used as an interrupt source, or routed to a Port pin through the
Crossbar.
The asynchronous “raw” comparator output (CP0A, CP1A) is used by the low power mode wakeup logic
and reset decision logic. See the Power Options chapter and the Reset Sources chapter for more details
on how the asynchronous comparator outputs are used to make wake-up and reset decisions. The asynchronous comparator output can also be routed directly to a Port pin through the Crossbar, and is available
for use outside the device even if the system clock is stopped.
When using a Comparator as an interrupt source, Comparator interrupts can be generated on rising-edge
and/or falling-edge comparator output transitions. Two independent interrupt flags (CPnRIF and CPnFIF)
allow software to determine which edge caused the Comparator interrupt. The comparator rising-edge and
falling-edge interrupt flags are set by hardware when a corresponding edge is detected regardless of the
interrupt enable state. Once set, these bits remain set until cleared by software.
The rising-edge and falling-edge interrupts can be individually enabled using the CPnRIE and CPnFIE
interrupt enable bits in the CPTnMD register. In order for the CPnRIF and/or CPnFIF interrupt flags to generate an interrupt request to the CPU, the Comparator must be enabled as an interrupt source and global
interrupts must be enabled. See the Interrupt Handler chapter for additional information.
CPT0CN
CP1EN
CP1OUT
CP1RIF
VDD
CP1FIF
CP1HYP1
CP1
Interrupt
CP1HYP0
CP1HYN1
CP1HYN0
CPT0MD
Analog Input Multiplexer
CP1FIE
CP1RIE
CP1MD1
CP1MD0
Px.x
CP1
Rising-edge
CP1 +
CP1
Falling-edge
Interrupt
Logic
Px.x
CP1
+
D
-
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Px.x
Crossbar
(SYNCHRONIZER)
CP1 -
GND
(ASYNCHRONOUS)
CP1A
Reset
Decision
Tree
Px.x
Figure 7.2. Comparator 1 Functional Block Diagram
Rev. 1.3
101
Si1000/1/2/3/4/5
7.3. Comparator Response Time
Comparator response time may be configured in software via the CPTnMD registers described on
“CPT0MD: Comparator 0 Mode Selection” on page 104 and “CPT1MD: Comparator 1 Mode Selection” on
page 106. Four response time settings are available: Mode 0 (Fastest Response Time), Mode 1, Mode 2,
and Mode 3 (Lowest Power). Selecting a longer response time reduces the Comparator active supply current. The Comparators also have low power shutdown state, which is entered any time the comparator is
disabled. Comparator rising edge and falling edge response times are typically not equal. See Table 4.13
on page 62 for complete comparator timing and supply current specifications.
7.4. Comparator Hysteresis
The Comparators feature software-programmable hysteresis that can be used to stabilize the comparator
output while a transition is occurring on the input. Using the CPTnCN registers, the user can program both
the amount of hysteresis voltage (referred to the input voltage) and the positive and negative-going symmetry of this hysteresis around the threshold voltage (i.e., the comparator negative input).
Figure 7.3 shows that when positive hysteresis is enabled, the comparator output does not transition from
logic 0 to logic 1 until the comparator positive input voltage has exceeded the threshold voltage by an
amount equal to the programmed hysteresis. It also shows that when negative hysteresis is enabled, the
comparator output does not transition from logic 1 to logic 0 until the comparator positive input voltage has
fallen below the threshold voltage by an amount equal to the programmed hysteresis.
The amount of positive hysteresis is determined by the settings of the CPnHYP bits in the CPTnCN register and the amount of negative hysteresis voltage is determined by the settings of the CPnHYN bits in the
same register. Settings of 20, 10, 5, or 0 mV can be programmed for both positive and negative hysteresis.
See Section “Table 4.13. Comparator Electrical Characteristics” on page 62 for complete comparator hysteresis specifications.
VIN+
VIN-
CPn+
CPn-
+
CPn
_
OUT
CIRCUIT CONFIGURATION
Positive Hysteresis Voltage
(Programmed with CP0HYP Bits)
VIN-
INPUTS
Negative Hysteresis Voltage
(Programmed by CP0HYN Bits)
VIN+
V OH
OUTPUT
V OL
Negative Hysteresis
Disabled
Positive Hysteresis
Disabled
Maximum
Negative Hysteresis
Maximum
Positive Hysteresis
Figure 7.3. Comparator Hysteresis Plot
102
Rev. 1.3
Si1000/1/2/3/4/5
7.5. Comparator Register Descriptions
The SFRs used to enable and configure the comparators are described in the following register descriptions. A Comparator must be enabled by setting the CPnEN bit to logic 1 before it can be used. From an
enabled state, a comparator can be disabled and placed in a low power state by clearing the CPnEN bit to
logic 0.
Important Note About Comparator Settings: False rising and falling edges can be detected by the Comparator while powering on or if changes are made to the hysteresis or response time control bits. Therefore, it is recommended that the rising-edge and falling-edge flags be explicitly cleared to logic 0 a short
time after the comparator is enabled or its mode bits have been changed. The Comparator Power Up Time
is specified in Section “Table 4.13. Comparator Electrical Characteristics” on page 62.
SFR Definition 7.1. CPT0CN: Comparator 0 Control
Bit
7
6
5
4
Name
CP0EN
CP0OUT
CP0RIF
CP0FIF
CP0HYP[1:0]
CP0HYN[1:0]
Type
R/W
R
R/W
R/W
R/W
R/W
Reset
0
0
0
0
SFR Page= 0x0; SFR Address = 0x9B
Bit
Name
7
CP0EN
3
2
0
0
1
0
0
0
Function
Comparator0 Enable Bit.
0: Comparator0 Disabled.
1: Comparator0 Enabled.
6
CP0OUT
Comparator0 Output State Flag.
0: Voltage on CP0+ < CP0–.
1: Voltage on CP0+ > CP0–.
5
CP0RIF
Comparator0 Rising-Edge Flag. Must be cleared by software.
0: No Comparator0 Rising Edge has occurred since this flag was last cleared.
1: Comparator0 Rising Edge has occurred.
4
CP0FIF
Comparator0 Falling-Edge Flag. Must be cleared by software.
0: No Comparator0 Falling-Edge has occurred since this flag was last cleared.
1: Comparator0 Falling-Edge has occurred.
3:2
CP0HYP[1:0] Comparator0 Positive Hysteresis Control Bits.
00: Positive Hysteresis Disabled.
01: Positive Hysteresis = 5 mV.
10: Positive Hysteresis = 10 mV.
11: Positive Hysteresis = 20 mV.
1:0
CP0HYN[1:0] Comparator0 Negative Hysteresis Control Bits.
00: Negative Hysteresis Disabled.
01: Negative Hysteresis = 5 mV.
10: Negative Hysteresis = 10 mV.
11: Negative Hysteresis = 20 mV.
Rev. 1.3
103
Si1000/1/2/3/4/5
SFR Definition 7.2. CPT0MD: Comparator 0 Mode Selection
Bit
7
6
Name
5
4
CP0RIE
CP0FIE
3
2
R/W
R
R/W
R/W
R
R
Reset
1
0
0
0
0
0
Reserved
6
Unused
Read = 0b, Write = don’t care.
5
CP0RIE
Comparator0 Rising-Edge Interrupt Enable.
0: Comparator0 Rising-edge interrupt disabled.
1: Comparator0 Rising-edge interrupt enabled.
4
CP0FIE
Comparator0 Falling-Edge Interrupt Enable.
0: Comparator0 Falling-edge interrupt disabled.
1: Comparator0 Falling-edge interrupt enabled.
3:2
Unused
Read = 00b, Write = don’t care.
104
R/W
1
0
Function
7
1:0
0
CP0MD[1:0]
Type
SFR Page = All Pages; SFR Address = 0x9D
Bit
Name
1
Read = 1b, Must Write 1b.
CP0MD[1:0] Comparator0 Mode Select.
These bits affect the response time and power consumption for Comparator0.
00: Mode 0 (Fastest Response Time, Highest Power Consumption)
01: Mode 1
10: Mode 2
11: Mode 3 (Slowest Response Time, Lowest Power Consumption)
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 7.3. CPT1CN: Comparator 1 Control
Bit
7
6
5
4
Name
CP1EN
CP1OUT
CP1RIF
CP1FIF
CP1HYP[1:0]
CP1HYN[1:0]
Type
R/W
R
R/W
R/W
R/W
R/W
Reset
0
0
0
0
SFR Page= 0x0; SFR Address = 0x9A
Bit
Name
7
CP1EN
3
2
0
0
1
0
0
0
Function
Comparator1 Enable Bit.
0: Comparator1 Disabled.
1: Comparator1 Enabled.
6
CP1OUT
Comparator1 Output State Flag.
0: Voltage on CP1+ < CP1–.
1: Voltage on CP1+ > CP1–.
5
CP1RIF
Comparator1 Rising-Edge Flag. Must be cleared by software.
0: No Comparator1 Rising Edge has occurred since this flag was last cleared.
1: Comparator1 Rising Edge has occurred.
4
CP1FIF
Comparator1 Falling-Edge Flag. Must be cleared by software.
0: No Comparator1 Falling-Edge has occurred since this flag was last cleared.
1: Comparator1 Falling-Edge has occurred.
3:2
CP1HYP[1:0] Comparator1 Positive Hysteresis Control Bits.
00: Positive Hysteresis Disabled.
01: Positive Hysteresis = 5 mV.
10: Positive Hysteresis = 10 mV.
11: Positive Hysteresis = 20 mV.
1:0
CP1HYN[1:0] Comparator1 Negative Hysteresis Control Bits.
00: Negative Hysteresis Disabled.
01: Negative Hysteresis = 5 mV.
10: Negative Hysteresis = 10 mV.
11: Negative Hysteresis = 20 mV.
Rev. 1.3
105
Si1000/1/2/3/4/5
SFR Definition 7.4. CPT1MD: Comparator 1 Mode Selection
Bit
7
6
Name
5
4
CP1RIE
CP1FIE
3
2
R/W
R
R/W
R/W
R
R
Reset
1
0
0
0
0
0
Reserved
6
Unused
Read = 00b, Write = don’t care.
5
CP1RIE
Comparator1 Rising-Edge Interrupt Enable.
0: Comparator1 Rising-edge interrupt disabled.
1: Comparator1 Rising-edge interrupt enabled.
4
CP1FIE
Comparator1 Falling-Edge Interrupt Enable.
0: Comparator1 Falling-edge interrupt disabled.
1: Comparator1 Falling-edge interrupt enabled.
3:2
Unused
Read = 00b, Write = don’t care.
106
R/W
1
0
Function
7
1:0
0
CP1MD[1:0]
Type
SFR Page = 0x0; SFR Address = 0x9C
Bit
Name
1
Read = 1b, Must Write 1b.
CP1MD[1:0] Comparator1 Mode Select
These bits affect the response time and power consumption for Comparator1.
00: Mode 0 (Fastest Response Time, Highest Power Consumption)
01: Mode 1
10: Mode 2
11: Mode 3 (Slowest Response Time, Lowest Power Consumption)
Rev. 1.3
Si1000/1/2/3/4/5
7.6. Comparator0 and Comparator1 Analog Multiplexers
Comparator0 and Comparator1 on Si1000/1/2/3/4/5 devices have analog input multiplexers to connect
Port I/O pins and internal signals the comparator inputs; CP0+/CP0- are the positive and negative input
multiplexers for Comparator0 and CP1+/CP1- are the positive and negative input multiplexers for Comparator1.
The comparator input multiplexers directly support capacitive touch switches. When the Capacitive Touch
Sense Compare input is selected on the positive or negative multiplexer, any Port I/O pin connected to the
other multiplexer can be directly connected to a capacitive touch switch with no additional external components. The Capacitive Touch Sense Compare provides the appropriate reference level for detecting when
the capacitive touch switches have charged or discharged through the on-chip Rsense resistor. The Comparator outputs can be routed to Timer2 or Timer3 for capturing sense capacitor’s charge and discharge
time. See Section “27. Timers” on page 335 for details. See Application Note AN338 for details on Capacitive Touch Switch sensing.
Any of the following may be selected as comparator inputs: Port I/O pins, Capacitive Touch Sense Compare, VDD_MCU Supply Voltage, Regulated Digital Supply Voltage (Output of VREG0) or ground. The
Comparator’s supply voltage divided by 2 is also available as an input; the resistors used to divide the voltage only draw current when this setting is selected. The Comparator input multiplexers are configured
using the CPT0MX and CPT1MX registers described in SFR Definition 7.5 and SFR Definition 7.6.
CMXnN3
CMXnN2
CMXnN1
CMXnN0
CMXnP3
CMXnP2
CMXnP1
CMXnP0
CPTnMX
P0.1
P0.3
P0.5
P0.7
CPnOUT
P1.5
P1.7
P2.1
P2.3
P2.5
VDD_MCU CPnOUT
R
R
R
R
CPnOUT
Rsense
Capacitive
Touch
Sense
Compare
(1/3 or 2/3) x VDD_MCU
VDD_MCU
R
P0.0
P0.2
P0.4
P0.6
P1.6
P2.0
P2.2
P2.4
P2.6
Capacitive
VDD_MCU CPnOUT
Touch
Sense
R
R
Compare
(1/3 or 2/3) x VDD_MCU
R
Rsense
Only enabled when
Capacitive Touch
Sense Compare is
selected on CPn+
Input MUX.
CPnInput
MUX
CPn+
Input
MUX
VDD_MCU
½ x VDD_MCU
Digital Supply
R
R
Only enabled when
Capacitive Touch
Sense Compare is
selected on CPnInput MUX.
VDD_MCU
+
GND
½ x VDD_MCU
VBAT
VDD_MCU
GND
Figure 7.4. CPn Multiplexer Block Diagram
Important Note About Comparator Input Configuration: Port pins selected as comparator inputs should
be configured as analog inputs, and should be skipped by the Digital Crossbar. To configure a Port pin for
analog input, set to 0 the corresponding bit in register PnMDIN and disable the digital driver (PnMDOUT =
0 and Port Latch = 1). To force the Crossbar to skip a Port pin, set to 1 the corresponding bit in register
PnSKIP. See Section “21. Port Input/Output” on page 210 for more Port I/O configuration details.
Rev. 1.3
107
Si1000/1/2/3/4/5
SFR Definition 7.5. CPT0MX: Comparator0 Input Channel Select
Bit
7
6
5
4
3
CMX0N[3:0]
Name
2
1
0
CMX0P[3:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
1
1
1
1
1
1
1
1
SFR Page = 0x0; SFR Address = 0x9F
Bit
Name
7:4
3:0
108
CMX0N
CMX0P
Function
Comparator0 Negative Input Selection.
Selects the negative input channel for Comparator0.
0000:
P0.1
1000:
P2.1
0001:
P0.3
1001:
P2.3
0010:
P0.5
1010:
P2.5
0011:
P0.7
1011:
Reserved
0100:
Reserved
1100:
Capacitive Touch Sense 
Compare
0101:
Reserved
1101:
VDD_MCU divided by 2
0110:
P1.5
1110:
Digital Supply Voltage
0111:
P1.7
1111:
Ground
Comparator0 Positive Input Selection.
Selects the positive input channel for Comparator0.
0000:
P0.0
1000:
P2.0
0001:
P0.2
1001:
P2.2
0010:
P0.4
1010:
P2.4
0011:
P0.6
1011:
P2.6
0100:
Reserved
1100:
Capacitive Touch Sense 
Compare
0101:
Reserved
1101:
VDD_MCU divided by 2
0110:
Reserved
1110:
VBAT Supply Voltage
0111:
P1.6
1111:
VDD_MCU Supply Voltage
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 7.6. CPT1MX: Comparator1 Input Channel Select
Bit
7
6
5
4
3
CMX1N[3:0]
Name
2
1
0
CMX1P[3:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
1
1
1
1
1
1
1
1
SFR Page = 0x0; SFR Address = 0x9E
Bit
Name
7:4
3:0
CMX1N
CMX1P
Function
Comparator1 Negative Input Selection.
Selects the negative input channel for Comparator1.
0000:
P0.1
1000:
P2.1
0001:
P0.3
1001:
P2.3
0010:
P0.5
1010:
P2.5
0011:
P0.7
1011:
Reserved
0100:
Reserved
1100:
Capacitive Touch Sense 
Compare
0101:
Reserved
1101:
VDD_MCU divided by 2
0110:
P1.5
1110:
Digital Supply Voltage
0111:
P1.7
1111:
Ground
Comparator1 Positive Input Selection.
Selects the positive input channel for Comparator1.
0000:
P0.0
1000:
P2.0
0001:
P0.2
1001:
P2.2
0010:
P0.4
1010:
P2.4
0011:
P0.6
1011:
P2.6
0100:
Reserved
1100:
Capacitive Touch Sense 
Compare
0101:
Reserved
1101:
VDD_MCU divided by 2
0110:
Reserved
1110:
VBAT Supply Voltage
0111:
P1.6
1111:
VDD_MCU Supply Voltage
Rev. 1.3
109
Si1000/1/2/3/4/5
8. CIP-51 Microcontroller
The MCU system controller core is the CIP-51 microcontroller. The CIP-51 is fully compatible with the
MCS-51™ instruction set; standard 803x/805x assemblers and compilers can be used to develop software. The MCU family has a superset of all the peripherals included with a standard 8051. The CIP-51
also includes on-chip debug hardware (see description in Section 29), and interfaces directly with the analog and digital subsystems providing a complete data acquisition or control-system solution in a single integrated circuit.
The CIP-51 Microcontroller core implements the standard 8051 organization and peripherals as well as
additional custom peripherals and functions to extend its capability (see Figure 8.1 for a block diagram).
The CIP-51 includes the following features:
Fully Compatible with MCS-51 Instruction Set
25 MIPS Peak Throughput with 25 MHz Clock
 0 to 25 MHz Clock Frequency
 Extended Interrupt Handler
Reset Input
Power Management Modes
 On-chip Debug Logic
 Program and Data Memory Security




8.1. Performance
The CIP-51 employs a pipelined architecture that greatly increases its instruction throughput over the standard 8051 architecture. In a standard 8051, all instructions except for MUL and DIV take 12 or 24 system
clock cycles to execute, and usually have a maximum system clock of 12 MHz. By contrast, the CIP-51
core executes 70% of its instructions in one or two system clock cycles, with no instructions taking more
than eight system clock cycles.
DATA BUS
D8
TMP2
B REGISTER
STACK POINTER
SRAM
ADDRESS
REGISTER
PSW
D8
D8
D8
ALU
SRAM
D8
D8
TMP1
ACCUMULATOR
D8
D8
D8
DATA BUS
DATA BUS
SFR_ADDRESS
BUFFER
D8
D8
DATA POINTER
D8
SFR
BUS
INTERFACE
SFR_CONTROL
SFR_WRITE_DATA
SFR_READ_DATA
DATA BUS
PC INCREMENTER
PROGRAM COUNTER (PC)
PRGM. ADDRESS REG.
PIPELINE
RESET
MEM_CONTROL
A16
MEMORY
INTERFACE
MEM_READ_DATA
SYSTEM_IRQs
D8
STOP
POWER CONTROL
REGISTER
MEM_WRITE_DATA
D8
CONTROL
LOGIC
CLOCK
IDLE
MEM_ADDRESS
D8
INTERRUPT
INTERFACE
EMULATION_IRQ
D8
Figure 8.1. CIP-51 Block Diagram
110
Rev. 1.3
Si1000/1/2/3/4/5
With the CIP-51's maximum system clock at 25 MHz, it has a peak throughput of 25 MIPS. The CIP-51 has
a total of 109 instructions. The table below shows the total number of instructions that require each execution time.
Clocks to Execute
1
2
2/3
3
3/4
4
4/5
5
8
Number of Instructions
26
50
5
14
7
3
1
2
1
8.2. Programming and Debugging Support
In-system programming of the flash program memory and communication with on-chip debug support logic
is accomplished via the Silicon Labs 2-Wire Development Interface (C2).
The on-chip debug support logic facilitates full speed in-circuit debugging, allowing the setting of hardware
breakpoints, starting, stopping and single stepping through program execution (including interrupt service
routines), examination of the program's call stack, and reading/writing the contents of registers and memory. This method of on-chip debugging is completely non-intrusive, requiring no RAM, Stack, timers, or
other on-chip resources. C2 details can be found in Section “29. Device Specific Behavior” on page 376.
The CIP-51 is supported by development tools from Silicon Labs and third party vendors. Silicon Labs provides an integrated development environment (IDE) including editor, debugger and programmer. The IDE's
debugger and programmer interface to the CIP-51 via the C2 interface to provide fast and efficient in-system device programming and debugging. Third party macro assemblers and C compilers are also available.
8.3. Instruction Set
The instruction set of the CIP-51 System Controller is fully compatible with the standard MCS-51™ instruction set. Standard 8051 development tools can be used to develop software for the CIP-51. All CIP-51
instructions are the binary and functional equivalent of their MCS-51™ counterparts, including opcodes,
addressing modes and effect on PSW flags. However, instruction timing is different than that of the standard 8051.
8.3.1. Instruction and CPU Timing
In many 8051 implementations, a distinction is made between machine cycles and clock cycles, with
machine cycles varying from 2 to 12 clock cycles in length. However, the CIP-51 implementation is based
solely on clock cycle timing. All instruction timings are specified in terms of clock cycles.
Due to the pipelined architecture of the CIP-51, most instructions execute in the same number of clock
cycles as there are program bytes in the instruction. Conditional branch instructions take one less clock
cycle to complete when the branch is not taken as opposed to when the branch is taken. Table 8.1 is the
CIP-51 Instruction Set Summary, which includes the mnemonic, number of bytes, and number of clock
cycles for each instruction.
Rev. 1.3
111
Si1000/1/2/3/4/5
Table 8.1. CIP-51 Instruction Set Summary
Mnemonic
Description
Bytes
Clock
Cycles
Add register to A
Add direct byte to A
Add indirect RAM to A
Add immediate to A
Add register to A with carry
Add direct byte to A with carry
Add indirect RAM to A with carry
Add immediate to A with carry
Subtract register from A with borrow
Subtract direct byte from A with borrow
Subtract indirect RAM from A with borrow
Subtract immediate from A with borrow
Increment A
Increment register
Increment direct byte
Increment indirect RAM
Decrement A
Decrement register
Decrement direct byte
Decrement indirect RAM
Increment Data Pointer
Multiply A and B
Divide A by B
Decimal adjust A
1
2
1
2
1
2
1
2
1
2
1
2
1
1
2
1
1
1
2
1
1
1
1
1
1
2
2
2
1
2
2
2
1
2
2
2
1
1
2
2
1
1
2
2
1
4
8
1
AND Register to A
AND direct byte to A
AND indirect RAM to A
AND immediate to A
AND A to direct byte
AND immediate to direct byte
OR Register to A
OR direct byte to A
OR indirect RAM to A
OR immediate to A
OR A to direct byte
OR immediate to direct byte
Exclusive-OR Register to A
Exclusive-OR direct byte to A
Exclusive-OR indirect RAM to A
Exclusive-OR immediate to A
Exclusive-OR A to direct byte
1
2
1
2
2
3
1
2
1
2
2
3
1
2
1
2
2
1
2
2
2
2
3
1
2
2
2
2
3
1
2
2
2
2
Arithmetic Operations
ADD A, Rn
ADD A, direct
ADD A, @Ri
ADD A, #data
ADDC A, Rn
ADDC A, direct
ADDC A, @Ri
ADDC A, #data
SUBB A, Rn
SUBB A, direct
SUBB A, @Ri
SUBB A, #data
INC A
INC Rn
INC direct
INC @Ri
DEC A
DEC Rn
DEC direct
DEC @Ri
INC DPTR
MUL AB
DIV AB
DA A
Logical Operations
ANL A, Rn
ANL A, direct
ANL A, @Ri
ANL A, #data
ANL direct, A
ANL direct, #data
ORL A, Rn
ORL A, direct
ORL A, @Ri
ORL A, #data
ORL direct, A
ORL direct, #data
XRL A, Rn
XRL A, direct
XRL A, @Ri
XRL A, #data
XRL direct, A
112
Rev. 1.3
Si1000/1/2/3/4/5
Table 8.1. CIP-51 Instruction Set Summary (Continued)
Mnemonic
XRL direct, #data
CLR A
CPL A
RL A
RLC A
RR A
RRC A
SWAP A
Description
Bytes
Clock
Cycles
Exclusive-OR immediate to direct byte
Clear A
Complement A
Rotate A left
Rotate A left through Carry
Rotate A right
Rotate A right through Carry
Swap nibbles of A
3
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
Move Register to A
Move direct byte to A
Move indirect RAM to A
Move immediate to A
Move A to Register
Move direct byte to Register
Move immediate to Register
Move A to direct byte
Move Register to direct byte
Move direct byte to direct byte
Move indirect RAM to direct byte
Move immediate to direct byte
Move A to indirect RAM
Move direct byte to indirect RAM
Move immediate to indirect RAM
Load DPTR with 16-bit constant
Move code byte relative DPTR to A
Move code byte relative PC to A
Move external data (8-bit address) to A
Move A to external data (8-bit address)
Move external data (16-bit address) to A
Move A to external data (16-bit address)
Push direct byte onto stack
Pop direct byte from stack
Exchange Register with A
Exchange direct byte with A
Exchange indirect RAM with A
Exchange low nibble of indirect RAM with A
1
2
1
2
1
2
2
2
2
3
2
3
1
2
2
3
1
1
1
1
1
1
2
2
1
2
1
1
1
2
2
2
1
2
2
2
2
3
2
3
2
2
2
3
3
3
3
3
3
3
2
2
1
2
2
2
Clear Carry
Clear direct bit
Set Carry
Set direct bit
Complement Carry
Complement direct bit
1
2
1
2
1
2
1
2
1
2
1
2
Data Transfer
MOV A, Rn
MOV A, direct
MOV A, @Ri
MOV A, #data
MOV Rn, A
MOV Rn, direct
MOV Rn, #data
MOV direct, A
MOV direct, Rn
MOV direct, direct
MOV direct, @Ri
MOV direct, #data
MOV @Ri, A
MOV @Ri, direct
MOV @Ri, #data
MOV DPTR, #data16
MOVC A, @A+DPTR
MOVC A, @A+PC
MOVX A, @Ri
MOVX @Ri, A
MOVX A, @DPTR
MOVX @DPTR, A
PUSH direct
POP direct
XCH A, Rn
XCH A, direct
XCH A, @Ri
XCHD A, @Ri
Boolean Manipulation
CLR C
CLR bit
SETB C
SETB bit
CPL C
CPL bit
Rev. 1.3
113
Si1000/1/2/3/4/5
Table 8.1. CIP-51 Instruction Set Summary (Continued)
Mnemonic
ANL C, bit
ANL C, /bit
ORL C, bit
ORL C, /bit
MOV C, bit
MOV bit, C
JC rel
JNC rel
JB bit, rel
JNB bit, rel
JBC bit, rel
Description
Bytes
Clock
Cycles
AND direct bit to Carry
AND complement of direct bit to Carry
OR direct bit to carry
OR complement of direct bit to Carry
Move direct bit to Carry
Move Carry to direct bit
Jump if Carry is set
Jump if Carry is not set
Jump if direct bit is set
Jump if direct bit is not set
Jump if direct bit is set and clear bit
2
2
2
2
2
2
2
2
3
3
3
2
2
2
2
2
2
2/3
2/3
3/4
3/4
3/4
Absolute subroutine call
Long subroutine call
Return from subroutine
Return from interrupt
Absolute jump
Long jump
Short jump (relative address)
Jump indirect relative to DPTR
Jump if A equals zero
Jump if A does not equal zero
Compare direct byte to A and jump if not equal
Compare immediate to A and jump if not equal
Compare immediate to Register and jump if not
equal
Compare immediate to indirect and jump if not
equal
Decrement Register and jump if not zero
Decrement direct byte and jump if not zero
No operation
2
3
1
1
2
3
2
1
2
2
3
3
3
3
4
5
5
3
4
3
3
2/3
2/3
4/5
3/4
3/4
3
4/5
2
3
1
2/3
3/4
1
Program Branching
ACALL addr11
LCALL addr16
RET
RETI
AJMP addr11
LJMP addr16
SJMP rel
JMP @A+DPTR
JZ rel
JNZ rel
CJNE A, direct, rel
CJNE A, #data, rel
CJNE Rn, #data, rel
CJNE @Ri, #data, rel
DJNZ Rn, rel
DJNZ direct, rel
NOP
114
Rev. 1.3
Si1000/1/2/3/4/5
Notes on Registers, Operands and Addressing Modes:
Rn - Register R0–R7 of the currently selected register bank.
@Ri - Data RAM location addressed indirectly through R0 or R1.
rel - 8-bit, signed (twos complement) offset relative to the first byte of the following instruction. Used by
SJMP and all conditional jumps.
direct - 8-bit internal data location’s address. This could be a direct-access Data RAM location (0x00–
0x7F) or an SFR (0x80–0xFF).
#data - 8-bit constant
#data16 - 16-bit constant
bit - Direct-accessed bit in Data RAM or SFR
addr11 - 11-bit destination address used by ACALL and AJMP. The destination must be within the same
2 kB page of program memory as the first byte of the following instruction.
addr16 - 16-bit destination address used by LCALL and LJMP. The destination may be anywhere within
the 8 kB program memory space.
There is one unused opcode (0xA5) that performs the same function as NOP.
All mnemonics copyrighted © Intel Corporation 1980.
Rev. 1.3
115
Si1000/1/2/3/4/5
8.4. CIP-51 Register Descriptions
Following are descriptions of SFRs related to the operation of the CIP-51 System Controller. Reserved bits
should not be set to logic l. Future product versions may use these bits to implement new features in which
case the reset value of the bit will be logic 0, selecting the feature's default state. Detailed descriptions of
the remaining SFRs are included in the sections of the data sheet associated with their corresponding system function.
SFR Definition 8.1. DPL: Data Pointer Low Byte
Bit
7
6
5
4
Name
DPL[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = All Pages; SFR Address = 0x82
Bit
Name
7:0
DPL[7:0]
3
2
1
0
0
0
0
0
Function
Data Pointer Low.
The DPL register is the low byte of the 16-bit DPTR. DPTR is used to access indirectly addressed flash memory or XRAM.
SFR Definition 8.2. DPH: Data Pointer High Byte
Bit
7
6
5
4
Name
DPH[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = All Pages; SFR Address = 0x83
Bit
Name
7:0
DPH[7:0]
3
2
1
0
0
0
0
0
Function
Data Pointer High.
The DPH register is the high byte of the 16-bit DPTR. DPTR is used to access indirectly addressed flash memory or XRAM.
116
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 8.3. SP: Stack Pointer
Bit
7
6
5
4
Name
SP[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = All Pages; SFR Address = 0x81
Bit
Name
7:0
SP[7:0]
3
2
1
0
0
1
1
1
Function
Stack Pointer.
The Stack Pointer holds the location of the top of the stack. The stack pointer is incremented before every PUSH operation. The SP register defaults to 0x07 after reset.
SFR Definition 8.4. ACC: Accumulator
Bit
7
6
5
4
Name
ACC[7:0]
Type
R/W
Reset
0
0
0
0
3
2
1
0
0
0
0
0
SFR Page = All Pages; SFR Address = 0xE0; Bit-Addressable
Bit
Name
Function
7:0
ACC[7:0]
Accumulator.
This register is the accumulator for arithmetic operations.
SFR Definition 8.5. B: B Register
Bit
7
6
5
4
Name
B[7:0]
Type
R/W
Reset
0
0
0
0
3
2
1
0
0
0
0
0
SFR Page = All Pages; SFR Address = 0xF0; Bit-Addressable
Bit
Name
Function
7:0
B[7:0]
B Register.
This register serves as a second accumulator for certain arithmetic operations.
Rev. 1.3
117
Si1000/1/2/3/4/5
SFR Definition 8.6. PSW: Program Status Word
Bit
7
6
5
Name
CY
AC
F0
Type
R/W
R/W
R/W
Reset
0
0
0
4
3
2
1
0
RS[1:0]
OV
F1
PARITY
R/W
R/W
R/W
R
0
0
0
0
0
SFR Page = All Pages; SFR Address = 0xD0; Bit-Addressable
Bit
Name
Function
7
CY
Carry Flag.
This bit is set when the last arithmetic operation resulted in a carry (addition) or a borrow (subtraction). It is cleared to logic 0 by all other arithmetic operations.
6
AC
Auxiliary Carry Flag.
This bit is set when the last arithmetic operation resulted in a carry into (addition) or a
borrow from (subtraction) the high order nibble. It is cleared to logic 0 by all other arithmetic operations.
5
F0
User Flag 0.
This is a bit-addressable, general purpose flag for use under software control.
4:3
RS[1:0]
Register Bank Select.
These bits select which register bank is used during register accesses.
00: Bank 0, Addresses 0x00-0x07
01: Bank 1, Addresses 0x08-0x0F
10: Bank 2, Addresses 0x10-0x17
11: Bank 3, Addresses 0x18-0x1F
2
OV
Overflow Flag.
This bit is set to 1 under the following circumstances:
An ADD, ADDC, or SUBB instruction causes a sign-change overflow.
 A MUL instruction results in an overflow (result is greater than 255).
 A DIV instruction causes a divide-by-zero condition.
The OV bit is cleared to 0 by the ADD, ADDC, SUBB, MUL, and DIV instructions in all
other cases.

1
F1
User Flag 1.
This is a bit-addressable, general purpose flag for use under software control.
0
PARITY
Parity Flag.
This bit is set to logic 1 if the sum of the eight bits in the accumulator is odd and cleared
if the sum is even.
118
Rev. 1.3
Si1000/1/2/3/4/5
9. Memory Organization
The memory organization of the CIP-51 System Controller is similar to that of a standard 8051. There are
two separate memory spaces: program memory and data memory. Program and data memory share the
same address space but are accessed via different instruction types. The memory organization of the
Si1000/1/2/3/4/5 device family is shown in Figure 9.1
PR OG RAM /DA TA M EM O R Y
(FLA SH)
DATA M EM O RY
(R AM )
INTERN AL DATA ADDR ESS SPACE
Si1000/2
U pper 128 R AM
0x03FF
0x0000
0xFFFF
Scrachpad M em ory
(D ATA only)
R ESER VED
0xFC00
0xFBFF
64KB FLASH
(In-System
Program m able in 1024
Byte Sectors)
Special Function
R egisters
(Indirect Addressing O nly) (D irect Addressing O nly)
0
F
(D irect and Indirect
Addressing)
Bit Addressable
G eneral Purpose
R egisters
0x0000
Low er 128 RAM
(D irect and Indirect
Addressing)
EXTERNAL DATA ADDR ESS SPACE
Si1001/3
0x03FF
0x0000
0xFFFF
Scrachpad M em ory
(D ATA only)
Reserved
0x7FFF
0x1000
32KB FLASH
0x0FFF
(In-System
Program m able in 1024
Byte Sectors)
XR AM - 4096 Bytes
(accessable using M O VX
instruction)
0x0000
0x0000
Figure 9.1. Si1000/1/2/3/4/5 Memory Map
Rev. 1.3
119
Si1000/1/2/3/4/5
9.1. Program Memory
The CIP-51 core has a 64 kB program memory space. The Si1000/1/2/3/4/5 implements 64 kB (Si1000/2)
or 32 kB (Si1001/3) of this program memory space as in-system, re-programmable flash memory, organized in a contiguous block from addresses 0x0000 to 0xFBFF (Si1000/2) or 0x7FFF (Si1001/3). The
address 0xFBFF (Si1000/2) or 0x7FFF (Si1001/3) serves as the security lock byte for the device. Any
addresses above the lock byte are reserved.
Si1000/2
(SFLE=0)
Si1001/3
(SFLE=0)
0xFFFF
0xFFFF
Reserved Area
0xFBFF
0xFBFE
Lock Byte Page
Unpopulated
Address Space
(Reserved)
0xF800
0xF7FF
0x8000
Lock Byte
Si1000/2
Si1001/3
(SFLE=1)
0x7FFE
Lock Byte Page
Flash Memory Space
0x7C00
0x7BFF
0x03FF
Scratchpad
(Data Only)
0x7FFF
FLASH memory organized in
1024-byte pages
0xFC00
Lock Byte
Flash Memory Space
0x0000
0x0000
0x0000
Figure 9.2. Flash Program Memory Map
9.1.1. MOVX Instruction and Program Memory
The MOVX instruction in an 8051 device is typically used to access external data memory. On the
Si1000/1/2/3/4/5 devices, the MOVX instruction is normally used to read and write on-chip XRAM, but can
be re-configured to write and erase on-chip flash memory space. MOVC instructions are always used to
read flash memory, while MOVX write instructions are used to erase and write flash. This flash access feature provides a mechanism for the Si1000/1/2/3/4/5 to update program code and use the program memory
space for non-volatile data storage. Refer to Section “13. Flash Memory” on page 142 for further details.
9.2. Data Memory
The Si1000/1/2/3/4/5 device family includes 4352 bytes of RAM data memory. 256 bytes of this memory is
mapped into the internal RAM space of the 8051. 4096 bytes of this memory is on-chip “external” memory.
The data memory map is shown in Figure 9.1 for reference.
9.2.1. Internal RAM
There are 256 bytes of internal RAM mapped into the data memory space from 0x00 through 0xFF. The
lower 128 bytes of data memory are used for general purpose registers and scratch pad memory. Either
direct or indirect addressing may be used to access the lower 128 bytes of data memory. Locations 0x00
through 0x1F are addressable as four banks of general purpose registers, each bank consisting of eight
byte-wide registers. The next 16 bytes, locations 0x20 through 0x2F, may either be addressed as bytes or
as 128 bit locations accessible with the direct addressing mode.
The upper 128 bytes of data memory are accessible only by indirect addressing. This region occupies the
same address space as the Special Function Registers (SFR) but is physically separate from the SFR
space. The addressing mode used by an instruction when accessing locations above 0x7F determines
whether the CPU accesses the upper 128 bytes of data memory space or the SFRs. Instructions that use
direct addressing will access the SFR space. Instructions using indirect addressing above 0x7F access the
120
Rev. 1.3
Si1000/1/2/3/4/5
upper 128 bytes of data memory. Figure 9.1 illustrates the data memory organization of the
Si1000/1/2/3/4/5.
9.2.1.1. General Purpose Registers
The lower 32 bytes of data memory, locations 0x00 through 0x1F, may be addressed as four banks of general-purpose registers. Each bank consists of eight byte-wide registers designated R0 through R7. Only
one of these banks may be enabled at a time. Two bits in the program status word, RS0 (PSW.3) and RS1
(PSW.4), select the active register bank (see description of the PSW in SFR Definition 8.6). This allows
fast context switching when entering subroutines and interrupt service routines. Indirect addressing modes
use registers R0 and R1 as index registers.
9.2.1.2. Bit Addressable Locations
In addition to direct access to data memory organized as bytes, the sixteen data memory locations at 0x20
through 0x2F are also accessible as 128 individually addressable bits. Each bit has a bit address from
0x00 to 0x7F. Bit 0 of the byte at 0x20 has bit address 0x00 while bit7 of the byte at 0x20 has bit address
0x07. Bit 7 of the byte at 0x2F has bit address 0x7F. A bit access is distinguished from a full byte access by
the type of instruction used (bit source or destination operands as opposed to a byte source or destination).
The MCS-51™ assembly language allows an alternate notation for bit addressing of the form XX.B where
XX is the byte address and B is the bit position within the byte. For example, the instruction:
MOV
C, 22.3h
moves the Boolean value at 0x13 (bit 3 of the byte at location 0x22) into the Carry flag.
9.2.1.3. Stack
A programmer's stack can be located anywhere in the 256-byte data memory. The stack area is designated using the Stack Pointer (SP) SFR. The SP will point to the last location used. The next value pushed
on the stack is placed at SP+1 and then SP is incremented. A reset initializes the stack pointer to location
0x07. Therefore, the first value pushed on the stack is placed at location 0x08, which is also the first register (R0) of register bank 1. Thus, if more than one register bank is to be used, the SP should be initialized
to a location in the data memory not being used for data storage. The stack depth can extend up to
256 bytes.
9.2.2. External RAM
There are 4096 bytes of on-chip RAM mapped into the external data memory space. All of these address
locations may be accessed using the external move instruction (MOVX) and the data pointer (DPTR), or
using MOVX indirect addressing mode (such as @R1) in combination with the EMI0CN register.
Rev. 1.3
121
Si1000/1/2/3/4/5
10. On-Chip XRAM
The Si1000/1/2/3/4/5 MCUs include on-chip RAM mapped into the external data memory space (XRAM).
The external memory space may be accessed using the external move instruction (MOVX) with the target
address specified in either the data pointer (DPTR), or with the target address low byte in R0 or R1 and the
target address high byte in the External Memory Interface Control Register (EMI0CN, shown in SFR Definition 10.1).
When using the MOVX instruction to access on-chip RAM, no additional initialization is required and the
MOVX instruction execution time is as specified in the CIP-51 chapter.
Important Note: MOVX write operations can be configured to target flash memory, instead of XRAM. See
Section “13. Flash Memory” on page 142 for more details. The MOVX instruction accesses XRAM by
default.
10.1. Accessing XRAM
The XRAM memory space is accessed using the MOVX instruction. The MOVX instruction has two forms,
both of which use an indirect addressing method. The first method uses the Data Pointer, DPTR, a 16-bit
register which contains the effective address of the XRAM location to be read from or written to. The second method uses R0 or R1 in combination with the EMI0CN register to generate the effective XRAM
address. Examples of both of these methods are given below.
10.1.1. 16-Bit MOVX Example
The 16-bit form of the MOVX instruction accesses the memory location pointed to by the contents of the
DPTR register. The following series of instructions reads the value of the byte at address 0x1234 into the
accumulator A:
MOV
MOVX
DPTR, #1234h
A, @DPTR
; load DPTR with 16-bit address to read (0x1234)
; load contents of 0x1234 into accumulator A

The above example uses the 16-bit immediate MOV instruction to set the contents of DPTR. Alternately,
the DPTR can be accessed through the SFR registers DPH, which contains the upper 8-bits of DPTR, and
DPL, which contains the lower 8-bits of DPTR.
10.1.2. 8-Bit MOVX Example
The 8-bit form of the MOVX instruction uses the contents of the EMI0CN SFR to determine the upper 8-bits
of the effective address to be accessed and the contents of R0 or R1 to determine the lower 8-bits of the
effective address to be accessed. The following series of instructions read the contents of the byte at
address 0x1234 into the accumulator A.
MOV
MOV
MOVX
122
EMI0CN, #12h
R0, #34h
a, @R0
; load high byte of address into EMI0CN
; load low byte of address into R0 (or R1)
; load contents of 0x1234 into accumulator A
Rev. 1.3
Si1000/1/2/3/4/5
10.2. Special Function Registers
The special function register used for configuring XRAM access is EMI0CN.
SFR Definition 10.1. EMI0CN: External Memory Interface Control
Bit
7
6
5
4
3
2
1
0
PGSEL[3:0]
Name
Type
R
R
R
R
Reset
0
0
0
0
R/W
0
0
0
0
SFR Page = 0x0; SFR Address = 0xAA
Bit
Name
Function
7:4
Unused
Read = 0000b; Write = Don’t Care.
3:0
PGSEL
XRAM Page Select.
The EMI0CN register provides the high byte of the 16-bit external data memory
address when using an 8-bit MOVX command, effectively selecting a 256-byte page
of RAM. Since the upper (unused) bits of the register are always zero, EMI0CN determines which page of XRAM is accessed.
For Example:
If EMI0CN = 0x01, addresses 0x0100 through 0x01FF will be accessed.
If EMI0CN = 0x0F, addresses 0x0F00 through 0x0FFF will be accessed.
Rev. 1.3
123
Si1000/1/2/3/4/5
11. Special Function Registers
The direct-access data memory locations from 0x80 to 0xFF constitute the special function registers
(SFRs). The SFRs provide control and data exchange with the Si1000/1/2/3/4/5's resources and peripherals. The CIP-51 controller core duplicates the SFRs found in a typical 8051 implementation as well as
implementing additional SFRs used to configure and access the sub-systems unique to the
Si1000/1/2/3/4/5. This allows the addition of new functionality while retaining compatibility with the MCS51™ instruction set. Table 11.1 and Table 11.2 list the SFRs implemented in the Si1000/1/2/3/4/5 device
family.
The SFR registers are accessed anytime the direct addressing mode is used to access memory locations
from 0x80 to 0xFF. SFRs with addresses ending in 0x0 or 0x8 (e.g. P0, TCON, SCON0, IE, etc.) are bitaddressable as well as byte-addressable. All other SFRs are byte-addressable only. Unoccupied
addresses in the SFR space are reserved for future use. Accessing these areas will have an indeterminate
effect and should be avoided. Refer to the corresponding pages of the data sheet, as indicated in
Table 11.3, for a detailed description of each register.
Table 11.1. Special Function Register (SFR) Memory Map (Page 0x0)
F8
F0
E8
E0
D8
D0
C8
C0
B8
B0
A8
A0
98
90
88
80
124
SPI0CN
PCA0L
PCA0H PCA0CPL0 PCA0CPH0
B
P0MDIN
P1MDIN
P2MDIN SMB0ADR
ADC0CN PCA0CPL1 PCA0CPH1 PCA0CPL2 PCA0CPH2
ACC
XBR0
XBR1
XBR2
IT01CF
PCA0CN PCA0MD PCA0CPM0 PCA0CPM1 PCA0CPM2
PSW
REF0CN PCA0CPL5 PCA0CPH5 P0SKIP
TMR2CN REG0CN TMR2RLL TMR2RLH
TMR2L
SMB0CN SMB0CF SMB0DAT ADC0GTL ADC0GTH
IP
IREF0CN ADC0AC ADC0MX
ADC0CF
SPI1CN OSCXCN OSCICN
OSCICL
IE
CLKSEL
EMI0CN
Reserved RTC0ADR
P2
SPI0CFG SPI0CKR SPI0DAT P0MDOUT
SCON0
SBUF0
CPT1CN
CPT0CN
CPT1MD
P1
TMR3CN TMR3RLL TMR3RLH
TMR3L
TCON
TMOD
TL0
TL1
TH0
P0
SP
DPL
DPH
SPI1CFG
0(8)
1(9)
2(A)
3(B)
4(C)
(bit addressable)
Rev. 1.3
PCA0CPL4
SMB0ADM
PCA0CPL3
PCA0CPM3
P1SKIP
TMR2H
ADC0LTL
ADC0L
PMU0CF
RTC0DAT
P1MDOUT
CPT0MD
TMR3H
TH1
SPI1CKR
5(D)
PCA0CPH4 VDM0CN
EIP1
EIP2
PCA0CPH3 RSTSRC
EIE1
EIE2
PCA0CPM4 PCA0PWM
P2SKIP
P0MAT
PCA0CPM5
P1MAT
ADC0LTH
P0MASK
ADC0H
P1MASK
FLSCL
FLKEY
RTC0KEY
Reserved
P2MDOUT SFRPAGE
CPT1MX
CPT0MX
DC0CF
DC0CN
CKCON
PSCTL
SPI1DAT
PCON
6(E)
7(F)
Si1000/1/2/3/4/5
11.1. SFR Paging
To accommodate more than 128 SFRs in the 0x80 to 0xFF address space, SFR paging has been implemented. By default, all SFR accesses target SFR Page 0x0 to allow access to the registers listed in
Table 11.1. During device initialization, some SFRs located on SFR Page 0xF may need to be accessed.
Table 11.2 lists the SFRs accessible from SFR Page 0x0F. Some SFRs are accessible from both pages,
including the SFRPAGE register. SFRs accessible only from Page 0xF are in bold.
The following procedure should be used when accessing SFRs from Page 0xF:
1. Save the current interrupt state (EA_save = EA).
2. Disable Interrupts (EA = 0).
3. Set SFRPAGE = 0xF.
4. Access the SFRs located on SFR Page 0xF.
5. Set SFRPAGE = 0x0.
6. Restore interrupt state (EA = EA_save).
Table 11.2. Special Function Register (SFR) Memory Map (Page 0xF)
F8
F0
E8
E0
D8
D0
C8
C0
B8
B0
A8
A0
98
90
88
80
B
EIP1
EIP2
ACC
EIE1
EIE2
P2DRV
SFRPAGE
PSW
ADC0PWR
IE
P2
CLKSEL
P1
CRC0DAT
ADC0TK
P0DRV
P0
SP
0(8)
1(9)
(bit addressable)
CRC0CN
CRC0IN
DPL
2(A)
DPH
3(B)
P1DRV
CRC0FLIP
4(C)
Rev. 1.3
TOFFL
5(D)
CRC0AUTO CRC0CNT
TOFFH
6(E)
PCON
7(F)
125
Si1000/1/2/3/4/5
SFR Definition 11.1. SFRPage: SFR Page
Bit
7
6
5
4
3
Name
SFRPAGE[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = All Pages; SFR Address = 0xA7
Bit
Name
0
2
1
0
0
0
0
Function
7:0 SFRPAGE[7:0] SFR Page.
Specifies the SFR Page used when reading, writing, or modifying special function
registers.
Table 11.3. Special Function Registers
SFRs are listed in alphabetical order. All undefined SFR locations are reserved
Register
ACC
ADC0AC
ADC0CF
ADC0CN
ADC0GTH
ADC0GTL
ADC0H
ADC0L
ADC0LTH
ADC0LTL
ADC0MX
ADC0PWR
ADC0TK
B
CKCON
CLKSEL
CPT0CN
CPT0MD
CPT0MX
CPT1CN
CPT1MD
CPT1MX
CRC0AUTO
CRC0CN
CRC0CNT
CRC0DAT
CRC0FLIP
126
Address
SFR Page
0xE0
0xBA
0xBC
0xE8
0xC4
0xC3
0xBE
0xBD
0xC6
0xC5
0xBB
0xBA
0xBD
0xF0
0x8E
0xA9
0x9B
0x9D
0x9F
0x9A
0x9C
0x9E
0x96
0x92
0x97
0x91
0x95
All
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0xF
0xF
All
0x0
All
0x0
0x0
0x0
0x0
0x0
0x0
0xF
0xF
0xF
0xF
0xF
Description
Accumulator
ADC0 Accumulator Configuration
ADC0 Configuration
ADC0 Control
ADC0 Greater-Than Compare High
ADC0 Greater-Than Compare Low
ADC0 High
ADC0 Low
ADC0 Less-Than Compare Word High
ADC0 Less-Than Compare Word Low
AMUX0 Channel Select
ADC0 Burst Mode Power-Up Time
ADC0 Tracking Control
B Register
Clock Control
Clock Select
Comparator0 Control
Comparator0 Mode Selection
Comparator0 Mux Selection
Comparator1 Control
Comparator1 Mode Selection
Comparator1 Mux Selection
CRC0 Automatic Control
CRC0 Control
CRC0 Automatic Flash Sector Count
CRC0 Data
CRC0 Flip
Rev. 1.3
Page
117
84
83
82
88
88
87
87
89
89
92
85
86
117
336
190
104
104
108
105
106
109
166
164
166
165
167
Si1000/1/2/3/4/5
Table 11.3. Special Function Registers (Continued)
SFRs are listed in alphabetical order. All undefined SFR locations are reserved
Register
Address
SFR Page
Description
CRC0IN
0x93
0xF
CRC0 Input
165
DC0CF
0x96
0x0
DC0 (DC-DC Converter) Configuration
175
DC0CN
0x97
0x0
DC0 (DC-DC Converter) Control
174
DPH
DPL
EIE1
EIE2
EIP1
EIP2
EMI0CN
FLKEY
FLSCL
IE
IP
IREF0CN
IT01CF
OSCICL
OSCICN
OSCXCN
P0
P0DRV
P0MASK
P0MAT
P0MDIN
P0MDOUT
P0SKIP
P1
P1DRV
P1MASK
P1MAT
P1MDIN
P1MDOUT
P1SKIP
P2
P2DRV
P2MDIN
P2MDOUT
P2SKIP
PCA0CN
PCA0CPH0
PCA0CPH1
PCA0CPH2
PCA0CPH3
PCA0CPH4
0x83
0x82
0xE6
0xE7
0xF6
0xF7
0xAA
0xB7
0xB6
0xA8
0xB8
0xB9
0xE4
0xB3
0xB2
0xB1
0x80
0xA4
0xC7
0xD7
0xF1
0xA4
0xD4
0x90
0xA5
0xBF
0xCF
0xF2
0xA5
0xD5
0xA0
0xA6
0xF3
0xA6
0xD6
0xD8
0xFC
0xEA
0xEC
0xEE
0xFE
All
All
All
All
0x0
0x0
0x0
0x0
0x0
All
0x0
0x0
0x0
0x0
0x0
0x0
All
0xF
0x0
0x0
0x0
0x0
0x0
All
0xF
0x0
0x0
0x0
0x0
0x0
All
0xF
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
Data Pointer High
Data Pointer Low
Extended Interrupt Enable 1
Extended Interrupt Enable 2
Extended Interrupt Priority 1
Extended Interrupt Priority 2
EMIF Control
Flash Lock And Key
Flash Scale
Interrupt Enable
Interrupt Priority
Current Reference IREF Control
INT0/INT1 Configuration
Internal Oscillator Calibration
Internal Oscillator Control
External Oscillator Control
Port 0 Latch
Port 0 Drive Strength
Port 0 Mask
Port 0 Match
Port 0 Input Mode Configuration
Port 0 Output Mode Configuration
Port 0 Skip
Port 1 Latch
Port 1 Drive Strength
Port 1 Mask
Port 1 Match
Port 1 Input Mode Configuration
Port 1 Output Mode Configuration
Port 1 Skip
Port 2 Latch
Port 2 Drive Strength
Port 2 Input Mode Configuration
Port 2 Output Mode Configuration
Port 2 Skip
PCA0 Control
PCA0 Capture 0 High
PCA0 Capture 1 High
PCA0 Capture 2 High
PCA0 Capture 3 High
PCA0 Capture 4 High
116
116
136
138
137
139
123
150
150
134
135
99
141
191
191
192
223
225
220
220
224
224
223
226
228
221
221
227
227
226
228
230
229
230
229
370
375
375
375
375
375
Rev. 1.3
Page
127
Si1000/1/2/3/4/5
Table 11.3. Special Function Registers (Continued)
SFRs are listed in alphabetical order. All undefined SFR locations are reserved
Register
PCA0CPH5
PCA0CPL0
PCA0CPL1
PCA0CPL2
PCA0CPL3
PCA0CPL4
PCA0CPL5
PCA0CPM0
PCA0CPM1
PCA0CPM2
PCA0CPM3
PCA0CPM4
PCA0CPM5
PCA0H
PCA0L
PCA0MD
PCA0PWM
PCON
PMU0CF
PSCTL
PSW
REF0CN
REG0CN
RSTSRC
RTC0ADR
RTC0DAT
RTC0KEY
SBUF0
SCON0
SFRPAGE
SMB0ADM
SMB0ADR
SMB0CF
SMB0CN
SMB0DAT
SP
SPI0CFG
SPI0CKR
SPI0CN
SPI0DAT
SPI1CFG
SPI1CKR
SPI1CN
SPI1DAT
128
Address
SFR Page
0xD3
0xFB
0xE9
0xEB
0xED
0xFD
0xD2
0xDA
0xDB
0xDC
0xDD
0xDE
0xCE
0xFA
0xF9
0xD9
0xDF
0x87
0xB5
0x8F
0xD0
0xD1
0xC9
0xEF
0xAC
0xAD
0xAE
0x99
0x98
0xA7
0xF5
0xF4
0xC1
0xC0
0xC2
0x81
0xA1
0xA2
0xF8
0xA3
0x84
0x85
0xB0
0x86
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
All
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
All
0x0
0x0
0x0
0x0
0x0
All
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
Description
PCA0 Capture 5 High
PCA0 Capture 0 Low
PCA0 Capture 1 Low
PCA0 Capture 2 Low
PCA0 Capture 3 Low
PCA0 Capture 4 Low
PCA0 Capture 5 Low
PCA0 Module 0 Mode Register
PCA0 Module 1 Mode Register
PCA0 Module 2 Mode Register
PCA0 Module 3 Mode Register
PCA0 Module 4 Mode Register
PCA0 Module 5 Mode Register
PCA0 Counter High
PCA0 Counter Low
PCA0 Mode
PCA0 PWM Configuration
Power Control
PMU0 Configuration
Program Store R/W Control
Program Status Word
Voltage Reference Control
Voltage Regulator (VREG0) Control
Reset Source Configuration/Status
RTC0 Address
RTC0 Data
RTC0 Key
UART0 Data Buffer
UART0 Control
SFR Page
SMBus Slave Address Mask
SMBus Slave Address
SMBus0 Configuration
SMBus0 Control
SMBus0 Data
Stack Pointer
SPI0 Configuration
SPI0 Clock Rate Control
SPI0 Control
SPI0 Data
SPI1 Configuration
SPI1 Clock Rate Control
SPI1 Control
SPI1 Data
Rev. 1.3
Page
375
375
375
375
375
375
375
373
373
373
373
373
373
374
374
371
372
158
157
149
118
98
177
184
198
199
197
320
319
126
302
302
297
299
305
117
329
331
330
331
329
331
330
331
Si1000/1/2/3/4/5
Table 11.3. Special Function Registers (Continued)
SFRs are listed in alphabetical order. All undefined SFR locations are reserved
Register
TCON
TH0
TH1
TL0
TL1
TMOD
TMR2CN
TMR2H
TMR2L
TMR2RLH
TMR2RLL
TMR3CN
TMR3H
TMR3L
TMR3RLH
TMR3RLL
TOFFH
TOFFL
VDM0CN
XBR0
XBR1
XBR2
Address
SFR Page
0x88
0x8C
0x8D
0x8A
0x8B
0x89
0xC8
0xCD
0xCC
0xCB
0xCA
0x91
0x95
0x94
0x93
0x92
0x86
0x85
0xFF
0xE1
0xE2
0xE3
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0xF
0xF
0x0
0x0
0x0
0x0
Description
Timer/Counter Control
Timer/Counter 0 High
Timer/Counter 1 High
Timer/Counter 0 Low
Timer/Counter 1 Low
Timer/Counter Mode
Timer/Counter 2 Control
Timer/Counter 2 High
Timer/Counter 2 Low
Timer/Counter 2 Reload High
Timer/Counter 2 Reload Low
Timer/Counter 3 Control
Timer/Counter 3 High
Timer/Counter 3 Low
Timer/Counter 3 Reload High
Timer/Counter 3 Reload Low
Temperature Offset High
Temperature Offset Low
VDD Monitor Control
Port I/O Crossbar Control 0
Port I/O Crossbar Control 1
Port I/O Crossbar Control 2
Rev. 1.3
Page
341
344
344
343
343
342
348
350
350
349
349
354
356
356
355
355
95
95
182
217
218
219
129
Si1000/1/2/3/4/5
12. Interrupt Handler
The Si1000/1/2/3/4/5 microcontroller family includes an extended interrupt system supporting multiple
interrupt sources and two priority levels. The allocation of interrupt sources between on-chip peripherals
and external input pins varies according to the specific version of the device. Refer to Table 12.1, “Interrupt
Summary,” on page 132 for a detailed listing of all interrupt sources supported by the device. Refer to the
data sheet section associated with a particular on-chip peripheral for information regarding valid interrupt
conditions for the peripheral and the behavior of its interrupt-pending flag(s).
Each interrupt source has one or more associated interrupt-pending flag(s) located in an SFR or an indirect register. When a peripheral or external source meets a valid interrupt condition, the associated interrupt-pending flag is set to logic 1. If both global interrupts and the specific interrupt source is enabled, a
CPU interrupt request is generated when the interrupt-pending flag is set.
As soon as execution of the current instruction is complete, the CPU generates an LCALL to a predetermined address to begin execution of an interrupt service routine (ISR). Each ISR must end with an RETI
instruction, which returns program execution to the next instruction that would have been executed if the
interrupt request had not occurred. If interrupts are not enabled, the interrupt-pending flag is ignored by the
hardware and program execution continues as normal. (The interrupt-pending flag is set to logic 1 regardless of the interrupt's enable/disable state.)
Some interrupt-pending flags are automatically cleared by hardware when the CPU vectors to the ISR.
However, most are not cleared by the hardware and must be cleared by software before returning from the
ISR. If an interrupt-pending flag remains set after the CPU completes the return-from-interrupt (RETI)
instruction, a new interrupt request will be generated immediately and the CPU will re-enter the ISR after
the completion of the next instruction.
12.1. Enabling Interrupt Sources
Each interrupt source can be individually enabled or disabled through the use of an associated interrupt
enable bit in the Interrupt Enable and Extended Interrupt Enable SFRs. However, interrupts must first be
globally enabled by setting the EA bit (IE.7) to logic 1 before the individual interrupt enables are recognized. Setting the EA bit to logic 0 disables all interrupt sources regardless of the individual interruptenable settings. Note that interrupts which occur when the EA bit is set to logic 0 will be held in a pending
state, and will not be serviced until the EA bit is set back to logic 1.
12.2. MCU Interrupt Sources and Vectors
The CPU services interrupts by generating an LCALL to a predetermined address (the interrupt vector
address) to begin execution of an interrupt service routine (ISR). The interrupt vector addresses associated with each interrupt source are listed in Table 12.1 on page 132. Software should ensure that the interrupt vector for each enabled interrupt source contains a valid interrupt service routine.
Software can simulate an interrupt by setting any interrupt-pending flag to logic 1. If interrupts are enabled
for the flag, an interrupt request will be generated and the CPU will vector to the ISR address associated
with the interrupt-pending flag.
130
Rev. 1.3
Si1000/1/2/3/4/5
12.3. Interrupt Priorities
Each interrupt source can be individually programmed to one of two priority levels: low or high. A low priority interrupt service routine can be preempted by a high priority interrupt. A high priority interrupt cannot be
preempted. If a high priority interrupt preempts a low priority interrupt, the low priority interrupt will finish
execution after the high priority interrupt completes. Each interrupt has an associated interrupt priority bit in
in the Interrupt Priority and Extended Interrupt Priority registers used to configure its priority level. Low priority is the default.
If two interrupts are recognized simultaneously, the interrupt with the higher priority is serviced first. If both
interrupts have the same priority level, a fixed priority order is used to arbitrate. See Table 12.1 on
page 132 to determine the fixed priority order used to arbitrate between simultaneously recognized interrupts.
12.4. Interrupt Latency
Interrupt response time depends on the state of the CPU when the interrupt occurs. Pending interrupts are
sampled and priority decoded each system clock cycle. Therefore, the fastest possible response time is 7
system clock cycles: 1 clock cycle to detect the interrupt, 1 clock cycle to execute a single instruction, and
5 clock cycles to complete the LCALL to the ISR. If an interrupt is pending when a RETI is executed, a single instruction is executed before an LCALL is made to service the pending interrupt. Therefore, the maximum response time for an interrupt (when no other interrupt is currently being serviced or the new interrupt
is of greater priority) occurs when the CPU is performing an RETI instruction followed by a DIV as the next
instruction. In this case, the response time is 19 system clock cycles: 1 clock cycle to detect the interrupt,
5 clock cycles to execute the RETI, 8 clock cycles to complete the DIV instruction and 5 clock cycles to
execute the LCALL to the ISR. If the CPU is executing an ISR for an interrupt with equal or higher priority,
the new interrupt will not be serviced until the current ISR completes, including the RETI and following
instruction.
Rev. 1.3
131
Si1000/1/2/3/4/5
Pending Flag
Priority Order
Bit addressable?
0x0000
Top
None
N/A N/A Always
Enabled
Always
Highest
External Interrupt 0 (INT0) 0x0003
0
IE0 (TCON.1)
Y
Y
EX0 (IE.0)
PX0 (IP.0)
Timer 0 Overflow
0x000B
1
TF0 (TCON.5)
Y
Y
ET0 (IE.1)
PT0 (IP.1)
External Interrupt 1 (INT1) 0x0013
2
IE1 (TCON.3)
Y
Y
EX1 (IE.2)
PX1 (IP.2)
Timer 1 Overflow
0x001B
3
TF1 (TCON.7)
Y
Y
ET1 (IE.3)
PT1 (IP.3)
UART0
0x0023
4
RI0 (SCON0.0)
TI0 (SCON0.1)
Y
N
ES0 (IE.4)
PS0 (IP.4)
Timer 2 Overflow
0x002B
5
TF2H (TMR2CN.7)
TF2L (TMR2CN.6)
Y
N
ET2 (IE.5)
PT2 (IP.5)
SPI0
0x0033
6
Y
SPIF (SPI0CN.7)
WCOL (SPI0CN.6)
MODF (SPI0CN.5)
RXOVRN (SPI0CN.4)
N
ESPI0
(IE.6)
PSPI0
(IP.6)
SMB0
0x003B
7
SI (SMB0CN.0)
Y
N
ESMB0
(EIE1.0)
PSMB0
(EIP1.0)
SmaRTClock Alarm
0x0043
8
ALRM (RTC0CN.2)*
N
N
EARTC0
(EIE1.1)
PARTC0
(EIP1.1)
ADC0 Window 
Comparator
0x004B
9
AD0WINT
(ADC0CN.3)
Y
N
EWADC0
(EIE1.2)
PWADC0
(EIP1.2)
ADC0 End of Conversion
0x0053
10
AD0INT (ADC0STA.5) Y
N
EADC0
(EIE1.3)
PADC0
(EIP1.3)
Programmable Counter
Array
0x005B
11
CF (PCA0CN.7)
CCFn (PCA0CN.n)
Y
N
EPCA0
(EIE1.4)
PPCA0
(EIP1.4)
Comparator0
0x0063
12
CP0FIF (CPT0CN.4)
CP0RIF (CPT0CN.5)
N
N
ECP0
(EIE1.5)
PCP0
(EIP1.5)
Comparator1
0x006B
13
CP1FIF (CPT1CN.4)
CP1RIF (CPT1CN.5)
N
N
ECP1
(EIE1.6)
PCP1
(EIP1.6)
Timer 3 Overflow
0x0073
14
TF3H (TMR3CN.7)
TF3L (TMR3CN.6)
N
N
ET3
(EIE1.7)
PT3
(EIP1.7)
VDD_MCU Supply 
Monitor Early Warning
0x007B
15
VDDOK
(VDM0CN.5)1
EWARN
(EIE2.0)
PWARN
(EIP2.0)
Port Match
0x0083
16
None
EMAT
(EIE2.1)
PMAT
(EIP2.1)
Interrupt Source
Reset
132
Rev. 1.3
Cleared by HW?
Interrupt Vector
Table 12.1. Interrupt Summary
Enable
Flag
Priority
Control
Si1000/1/2/3/4/5
0x0093
Cleared by HW?
EZRadioPRO Serial 
Interface (SPI1)
Priority
Control
N
N
ERTC0F
(EIE2.2)
PFRTC0F
(EIP2.2)
N
ESPI1
(EIE2.3)
PSPI1
(EIP2.3)
Pending Flag
Priority Order
SmaRTClock Oscillator
Fail
Enable
Flag
Interrupt Vector
Interrupt Source
Bit addressable?
Table 12.1. Interrupt Summary (Continued)
0x008B
17
OSCFAIL
(RTC0CN.5)2
18
N
SPIF (SPI1CN.7)
WCOL (SPI1CN.6)
MODF (SPI1CN.5)
RXOVRN (SPI1CN.4)
Notes:
1. Indicates a read-only interrupt pending flag. The interrupt enable may be used to prevent software from
vectoring to the associated interrupt service routine.
2. Indicates a register located in an indirect memory space.
12.5. Interrupt Register Descriptions
The SFRs used to enable the interrupt sources and set their priority level are described in the following
register descriptions. Refer to the data sheet section associated with a particular on-chip peripheral for
information regarding valid interrupt conditions for the peripheral and the behavior of its interrupt-pending
flag(s).
Rev. 1.3
133
Si1000/1/2/3/4/5
SFR Definition 12.1. IE: Interrupt Enable
Bit
7
6
5
4
3
2
1
0
Name
EA
ESPI0
ET2
ES0
ET1
EX1
ET0
EX0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = All Pages; SFR Address = 0xA8; Bit-Addressable
Bit
Name
Function
7
EA
6
ESPI0
5
ET2
Enable Timer 2 Interrupt.
This bit sets the masking of the Timer 2 interrupt.
0: Disable Timer 2 interrupt.
1: Enable interrupt requests generated by the TF2L or TF2H flags.
4
ES0
Enable UART0 Interrupt.
This bit sets the masking of the UART0 interrupt.
0: Disable UART0 interrupt.
1: Enable UART0 interrupt.
3
ET1
Enable Timer 1 Interrupt.
This bit sets the masking of the Timer 1 interrupt.
0: Disable all Timer 1 interrupt.
1: Enable interrupt requests generated by the TF1 flag.
2
EX1
Enable External Interrupt 1.
This bit sets the masking of External Interrupt 1.
0: Disable external interrupt 1.
1: Enable interrupt requests generated by the INT1 input.
1
ET0
Enable Timer 0 Interrupt.
This bit sets the masking of the Timer 0 interrupt.
0: Disable all Timer 0 interrupt.
1: Enable interrupt requests generated by the TF0 flag.
0
EX0
Enable External Interrupt 0.
This bit sets the masking of External Interrupt 0.
0: Disable external interrupt 0.
1: Enable interrupt requests generated by the INT0 input.
134
Enable All Interrupts.
Globally enables/disables all interrupts. It overrides individual interrupt mask settings.
0: Disable all interrupt sources.
1: Enable each interrupt according to its individual mask setting.
Enable Serial Peripheral Interface (SPI0) Interrupt.
This bit sets the masking of the SPI0 interrupts.
0: Disable all SPI0 interrupts.
1: Enable interrupt requests generated by SPI0.
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 12.2. IP: Interrupt Priority
Bit
7
Name
6
5
4
3
2
1
0
PSPI0
PT2
PS0
PT1
PX1
PT0
PX0
Type
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
1
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xB8; Bit-Addressable
Bit
Name
Function
7
6
Unused
PSPI0
Read = 1b, Write = don't care.
5
PT2
Timer 2 Interrupt Priority Control.
This bit sets the priority of the Timer 2 interrupt.
0: Timer 2 interrupt set to low priority level.
1: Timer 2 interrupt set to high priority level.
4
PS0
UART0 Interrupt Priority Control.
This bit sets the priority of the UART0 interrupt.
0: UART0 interrupt set to low priority level.
1: UART0 interrupt set to high priority level.
3
PT1
Timer 1 Interrupt Priority Control.
This bit sets the priority of the Timer 1 interrupt.
0: Timer 1 interrupt set to low priority level.
1: Timer 1 interrupt set to high priority level.
2
PX1
External Interrupt 1 Priority Control.
This bit sets the priority of the External Interrupt 1 interrupt.
0: External Interrupt 1 set to low priority level.
1: External Interrupt 1 set to high priority level.
1
PT0
Timer 0 Interrupt Priority Control.
This bit sets the priority of the Timer 0 interrupt.
0: Timer 0 interrupt set to low priority level.
1: Timer 0 interrupt set to high priority level.
0
PX0
External Interrupt 0 Priority Control.
This bit sets the priority of the External Interrupt 0 interrupt.
0: External Interrupt 0 set to low priority level.
1: External Interrupt 0 set to high priority level.
Serial Peripheral Interface (SPI0) Interrupt Priority Control.
This bit sets the priority of the SPI0 interrupt.
0: SPI0 interrupt set to low priority level.
1: SPI0 interrupt set to high priority level.
Rev. 1.3
135
Si1000/1/2/3/4/5
SFR Definition 12.3. EIE1: Extended Interrupt Enable 1
Bit
7
6
5
4
3
2
1
0
Name
ET3
ECP1
ECP0
EPCA0
EADC0
EWADC0
ERTC0A
ESMB0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = All Pages; SFR Address = 0xE6
Bit
Name
Function
7
ET3
6
ECP1
Enable Comparator1 (CP1) Interrupt.
This bit sets the masking of the CP1 interrupt.
0: Disable CP1 interrupts.
1: Enable interrupt requests generated by the CP1RIF or CP1FIF flags.
5
ECP0
Enable Comparator0 (CP0) Interrupt.
This bit sets the masking of the CP0 interrupt.
0: Disable CP0 interrupts.
1: Enable interrupt requests generated by the CP0RIF or CP0FIF flags.
4
EPCA0
Enable Programmable Counter Array (PCA0) Interrupt.
This bit sets the masking of the PCA0 interrupts.
0: Disable all PCA0 interrupts.
1: Enable interrupt requests generated by PCA0.
3
EADC0
Enable ADC0 Conversion Complete Interrupt.
This bit sets the masking of the ADC0 Conversion Complete interrupt.
0: Disable ADC0 Conversion Complete interrupt.
1: Enable interrupt requests generated by the AD0INT flag.
Enable Timer 3 Interrupt.
This bit sets the masking of the Timer 3 interrupt.
0: Disable Timer 3 interrupts.
1: Enable interrupt requests generated by the TF3L or TF3H flags.
2
EWADC0 Enable Window Comparison ADC0 Interrupt.
This bit sets the masking of ADC0 Window Comparison interrupt.
0: Disable ADC0 Window Comparison interrupt.
1: Enable interrupt requests generated by ADC0 Window Compare flag (AD0WINT).
1
ERTC0A
Enable SmaRTClock Alarm Interrupts.
This bit sets the masking of the SmaRTClock Alarm interrupt.
0: Disable SmaRTClock Alarm interrupts.
1: Enable interrupt requests generated by a SmaRTClock Alarm.
0
ESMB0
Enable SMBus (SMB0) Interrupt.
This bit sets the masking of the SMB0 interrupt.
0: Disable all SMB0 interrupts.
1: Enable interrupt requests generated by SMB0.
136
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 12.4. EIP1: Extended Interrupt Priority 1
Bit
7
6
5
4
3
2
1
0
Name
PT3
PCP1
PCP0
PPCA0
PADC0
PWADC0
PRTC0A
PSMB0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = All Pages; SFR Address = 0xF6
Bit
Name
Function
7
PT3
Timer 3 Interrupt Priority Control.
This bit sets the priority of the Timer 3 interrupt.
0: Timer 3 interrupts set to low priority level.
1: Timer 3 interrupts set to high priority level.
6
PCP1
Comparator1 (CP1) Interrupt Priority Control.
This bit sets the priority of the CP1 interrupt.
0: CP1 interrupt set to low priority level.
1: CP1 interrupt set to high priority level.
5
PCP0
Comparator0 (CP0) Interrupt Priority Control.
This bit sets the priority of the CP0 interrupt.
0: CP0 interrupt set to low priority level.
1: CP0 interrupt set to high priority level.
4
PPCA0
Programmable Counter Array (PCA0) Interrupt Priority Control.
This bit sets the priority of the PCA0 interrupt.
0: PCA0 interrupt set to low priority level.
1: PCA0 interrupt set to high priority level.
3
PADC0
ADC0 Conversion Complete Interrupt Priority Control.
This bit sets the priority of the ADC0 Conversion Complete interrupt.
0: ADC0 Conversion Complete interrupt set to low priority level.
1: ADC0 Conversion Complete interrupt set to high priority level.
2
PWADC0 ADC0 Window Comparator Interrupt Priority Control.
This bit sets the priority of the ADC0 Window interrupt.
0: ADC0 Window interrupt set to low priority level.
1: ADC0 Window interrupt set to high priority level.
1
PRTC0A
SmaRTClock Alarm Interrupt Priority Control.
This bit sets the priority of the SmaRTClock Alarm interrupt.
0: SmaRTClock Alarm interrupt set to low priority level.
1: SmaRTClock Alarm interrupt set to high priority level.
0
PSMB0
SMBus (SMB0) Interrupt Priority Control.
This bit sets the priority of the SMB0 interrupt.
0: SMB0 interrupt set to low priority level.
1: SMB0 interrupt set to high priority level.
Rev. 1.3
137
Si1000/1/2/3/4/5
SFR Definition 12.5. EIE2: Extended Interrupt Enable 2
Bit
7
6
5
4
Name
3
2
1
0
ESPI1
ERTC0F
EMAT
EWARN
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = All Pages;SFR Address = 0xE7
Bit
Name
7:4
3
2
1
0
138
Function
Unused Read = 0000b. Write = Don’t care.
ESPI1
Enable Serial Peripheral Interface (SPI1) Interrupt.
This bit sets the masking of the SPI1 interrupts.
0: Disable all SPI1 interrupts.
1: Enable interrupt requests generated by SPI1.
ERTC0F Enable SmaRTClock Oscillator Fail Interrupt.
This bit sets the masking of the SmaRTClock Alarm interrupt.
0: Disable SmaRTClock Alarm interrupts.
1: Enable interrupt requests generated by SmaRTClock Alarm.
EMAT
Enable Port Match Interrupts.
This bit sets the masking of the Port Match Event interrupt.
0: Disable all Port Match interrupts.
1: Enable interrupt requests generated by a Port Match.
EWARN Enable VDD_MCU Supply Monitor Early Warning Interrupt.
This bit sets the masking of the VDD_MCU Supply Monitor Early Warning interrupt.
0: Disable the VDD_MCU Supply Monitor Early Warning interrupt.
1: Enable interrupt requests generated by VDD_MCU Supply Monitor.
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 12.6. EIP2: Extended Interrupt Priority 2
Bit
7
6
5
4
Name
3
2
1
0
PSPI1
PRTC0F
PMAT
PWARN
Type
R
R
R
R
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = All Pages; SFR Address = 0xF7
Bit
Name
Function
7:4
Unused
Read = 0000b. Write = Don’t care.
3
PSPI1
Serial Peripheral Interface (SPI1) Interrupt Priority Control.
This bit sets the priority of the SPI1 interrupt.
0: SP1 interrupt set to low priority level.
1: SPI1 interrupt set to high priority level.
2
1
0
PRTC0F SmaRTClock Oscillator Fail Interrupt Priority Control.
This bit sets the priority of the SmaRTClock Alarm interrupt.
0: SmaRTClock Alarm interrupt set to low priority level.
1: SmaRTClock Alarm interrupt set to high priority level.
PMAT
Port Match Interrupt Priority Control.
This bit sets the priority of the Port Match Event interrupt.
0: Port Match interrupt set to low priority level.
1: Port Match interrupt set to high priority level.
PWARN VDD_MCU Supply Monitor Early Warning Interrupt Priority Control.
This bit sets the priority of the VDD_MCU Supply Monitor Early Warning interrupt.
0: VDD_MCU Supply Monitor Early Warning interrupt set to low priority level.
1: VDD_MCU Supply Monitor Early Warning interrupt set to high priority level.
Rev. 1.3
139
Si1000/1/2/3/4/5
12.6. External Interrupts INT0 and INT1
The INT0 and INT1 external interrupt sources are configurable as active high or low, edge or level sensitive. The IN0PL (INT0 Polarity) and IN1PL (INT1 Polarity) bits in the IT01CF register select active high or
active low; the IT0 and IT1 bits in TCON (Section “27.1. Timer 0 and Timer 1” on page 337) select level or
edge sensitive. The table below lists the possible configurations.
IT0
IN0PL
INT0 Interrupt
IT1
IN1PL
INT1 Interrupt
1
0
Active low, edge sensitive
1
0
Active low, edge sensitive
1
1
Active high, edge sensitive
1
1
Active high, edge sensitive
0
0
Active low, level sensitive
0
0
Active low, level sensitive
0
1
Active high, level sensitive
0
1
Active high, level sensitive
INT0 and INT1 are assigned to Port pins as defined in the IT01CF register (see SFR Definition 12.7). Note
that INT0 and INT0 Port pin assignments are independent of any Crossbar assignments. INT0 and INT1
will monitor their assigned Port pins without disturbing the peripheral that was assigned the Port pin via the
Crossbar. To assign a Port pin only to INT0 and/or INT1, configure the Crossbar to skip the selected pin(s).
This is accomplished by setting the associated bit in register XBR0 (see Section “21.3. Priority Crossbar
Decoder” on page 214 for complete details on configuring the Crossbar).
IE0 (TCON.1) and IE1 (TCON.3) serve as the interrupt-pending flags for the INT0 and INT1 external interrupts, respectively. If an INT0 or INT1 external interrupt is configured as edge-sensitive, the corresponding
interrupt-pending flag is automatically cleared by the hardware when the CPU vectors to the ISR. When
configured as level sensitive, the interrupt-pending flag remains logic 1 while the input is active as defined
by the corresponding polarity bit (IN0PL or IN1PL); the flag remains logic 0 while the input is inactive. The
external interrupt source must hold the input active until the interrupt request is recognized. It must then
deactivate the interrupt request before execution of the ISR completes or another interrupt request will be
generated.
140
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 12.7. IT01CF: INT0/INT1 Configuration
Bit
7
6
Name
IN1PL
IN1SL[2:0]
IN0PL
IN0SL[2:0]
Type
R/W
R/W
R/W
R/W
Reset
0
0
5
0
4
0
3
0
2
0
1
0
0
1
SFR Page = 0x0; SFR Address = 0xE4
Bit
Name
7
IN1PL
6:4
3
2:0
Function
INT1 Polarity.
0: INT1 input is active low.
1: INT1 input is active high.
IN1SL[2:0] INT1 Port Pin Selection Bits.
These bits select which Port pin is assigned to INT1. Note that this pin assignment is
independent of the Crossbar; INT1 will monitor the assigned Port pin without disturbing the peripheral that has been assigned the Port pin via the Crossbar. The Crossbar
will not assign the Port pin to a peripheral if it is configured to skip the selected pin.
000: Select P0.0
001: Select P0.1
010: Select P0.2
011: Select P0.3
100: Select P0.4
101: Select P0.5
110: Select P0.6
111: Select P0.7
IN0PL
INT0 Polarity.
0: INT0 input is active low.
1: INT0 input is active high.
IN0SL[2:0] INT0 Port Pin Selection Bits.
These bits select which Port pin is assigned to INT0. Note that this pin assignment is
independent of the Crossbar; INT0 will monitor the assigned Port pin without disturbing the peripheral that has been assigned the Port pin via the Crossbar. The Crossbar
will not assign the Port pin to a peripheral if it is configured to skip the selected pin.
000: Select P0.0
001: Select P0.1
010: Select P0.2
011: Select P0.3
100: Select P0.4
101: Select P0.5
110: Select P0.6
111: Select P0.7
Rev. 1.3
141
Si1000/1/2/3/4/5
13. Flash Memory
On-chip, re-programmable flash memory is included for program code and non-volatile data storage. The
flash memory can be programmed in-system through the C2 interface or by software using the MOVX
write instruction. Once cleared to logic 0, a flash bit must be erased to set it back to logic 1. Flash bytes
would typically be erased (set to 0xFF) before being reprogrammed. The write and erase operations are
automatically timed by hardware for proper execution; data polling to determine the end of the write/erase
operations is not required. Code execution is stalled during flash write/erase operations. Refer to Table 4.6
for complete flash memory electrical characteristics.
13.1. Programming the Flash Memory
The simplest means of programming the flash memory is through the C2 interface using programming
tools provided by Silicon Laboratories or a third party vendor. This is the only means for programming a
non-initialized device. For details on the C2 commands to program flash memory, see Section “29. Device
Specific Behavior” on page 376.
The flash memory can be programmed by software using the MOVX write instruction with the address and
data byte to be programmed provided as normal operands. Before programming flash memory using
MOVX, flash programming operations must be enabled by: (1) setting the PSWE Program Store Write
Enable bit (PSCTL.0) to logic 1 (this directs the MOVX writes to target flash memory); and (2) Writing the
flash key codes in sequence to the flash lock register (FLKEY). The PSWE bit remains set until cleared by
software. For detailed guidelines on programming flash from firmware, please see Section “13.5. Flash
Write and Erase Guidelines” on page 146.
To ensure the integrity of the flash contents, the on-chip VDD Monitor must be enabled and enabled as a
reset source in any system that includes code that writes and/or erases flash memory from software. Furthermore, there should be no delay between enabling the VDD Monitor and enabling the VDD Monitor as a
reset source. Any attempt to write or erase flash memory while the VDD Monitor is disabled, or not enabled
as a reset source, will cause a flash error device reset.
13.1.1. Flash Lock and Key Functions
Flash writes and erases by user software are protected with a lock and key function. The flash lock and key
register (FLKEY) must be written with the correct key codes, in sequence, before flash operations may be
performed. The key codes are: 0xA5, 0xF1. The timing does not matter, but the codes must be written in
order. If the key codes are written out of order, or the wrong codes are written, flash writes and erases will
be disabled until the next system reset. Flash writes and erases will also be disabled if a flash write or
erase is attempted before the key codes have been written properly. The flash lock resets after each write
or erase; the key codes must be written again before a following flash operation can be performed. The
FLKEY register is detailed in SFR Definition 13.2.
142
Rev. 1.3
Si1000/1/2/3/4/5
13.1.2. Flash Erase Procedure
The flash memory is organized in 1024-byte pages. The erase operation applies to an entire page (setting
all bytes in the page to 0xFF). To erase an entire 1024-byte page, perform the following steps:
1. Save current interrupt state and disable interrupts.
2. Set the PSEE bit (register PSCTL).
3. Set the PSWE bit (register PSCTL).
4. Write the first key code to FLKEY: 0xA5.
5. Write the second key code to FLKEY: 0xF1.
6. Using the MOVX instruction, write a data byte to any location within the 1024-byte page to be erased.
7. Clear the PSWE and PSEE bits.
8. Restore previous interrupt state.
Steps 4–6 must be repeated for each 1024-byte page to be erased.
Notes:
1. Future 16 and 8 kB derivatives in this product family will use a 512-byte page size. To maintain code
compatibility across the entire family, the erase procedure should be performed on each 512-byte section of
memory.
2. Flash security settings may prevent erasure of some flash pages, such as the reserved area and the page
containing the lock bytes. For a summary of flash security settings and restrictions affecting flash erase
operations, please see Section “13.3. Security Options” on page 144.
3. 8-bit MOVX instructions cannot be used to erase or write to flash memory at addresses higher than 0x00FF.
13.1.3. Flash Write Procedure
A write to flash memory can clear bits to logic 0 but cannot set them; only an erase operation can set bits
to logic 1 in flash. A byte location to be programmed should be erased before a new value is written.
The recommended procedure for writing a single byte in flash is as follows:
1. Save current interrupt state and disable interrupts.
2. Ensure that the flash byte has been erased (has a value of 0xFF).
3. Set the PSWE bit (register PSCTL).
4. Clear the PSEE bit (register PSCTL).
5. Write the first key code to FLKEY: 0xA5.
6. Write the second key code to FLKEY: 0xF1.
7. Using the MOVX instruction, write a single data byte to the desired location within the 1024-byte sector.
8. Clear the PSWE bit.
9. Restore previous interrupt state.
Steps 5–7 must be repeated for each byte to be written.
Notes:
1. Future 16 and 8 kB derivatives in this product family will use a 512-byte page size. To maintain code
compatibility across the entire family, the erase procedure should be performed on each 512-byte section of
memory.
2. Flash security settings may prevent writes to some areas of flash, such as the reserved area. For a summary of
flash security settings and restrictions affecting flash write operations, please see Section “13.3. Security
Options” on page 144.
Rev. 1.3
143
Si1000/1/2/3/4/5
13.2. Non-volatile Data Storage
The flash memory can be used for non-volatile data storage as well as program code. This allows data
such as calibration coefficients to be calculated and stored at run time. Data is written using the MOVX
write instruction and read using the MOVC instruction. Note: MOVX read instructions always target XRAM.
An additional 1024-byte scratchpad is available for non-volatile data storage. It is accessible at addresses
0x0000 to 0x03FF when SFLE is set to 1. The scratchpad area cannot be used for code execution.
13.3. Security Options
The CIP-51 provides security options to protect the flash memory from inadvertent modification by software as well as to prevent the viewing of proprietary program code and constants. The Program Store
Write Enable (bit PSWE in register PSCTL) and the Program Store Erase Enable (bit PSEE in register
PSCTL) bits protect the flash memory from accidental modification by software. PSWE must be explicitly
set to 1 before software can modify the flash memory; both PSWE and PSEE must be set to 1 before software can erase flash memory. Additional security features prevent proprietary program code and data constants from being read or altered across the C2 interface.
A Security Lock Byte located at the last byte of flash user space offers protection of the flash program
memory from access (reads, writes, or erases) by unprotected code or the C2 interface. The flash security
mechanism allows the user to lock n 1024-byte flash pages, starting at page 0 (addresses 0x0000 to
0x03FF), where n is the 1s complement number represented by the Security Lock Byte. Note that the
page containing the flash Security Lock Byte is unlocked when no other flash pages are locked (all
bits of the Lock Byte are 1) and locked when any other flash pages are locked (any bit of the Lock
Byte is 0). See the Si1000 example below.
Security Lock Byte:
ones Complement:
Flash pages locked:
11111101b
00000010b
3 (First two flash pages + Lock Byte Page)
Addresses locked:
0x0000 to 0x07FF (first two flash pages) and
0xF800 to 0xFBFF (Lock Byte Page)
64KB Flash Device
(SFLE = 0)
32KB Flash Device
(SFLE = 0)
0xFFFF
0xFFFF
Reserved
Unpopulated
Address Space
(Reserved)
0xFC00
0xFBFF
Lock Byte
0xFBFE
Lock Byte Page
0xF800
Locked when
any other
Flash pages
are locked
0x8000
Lock Byte
Lock Byte Page
Flash
memory
organized in
1024-byte
pages
0x7FFF
0x7FFE
0x7C00
Unlocked Flash Pages
64/32KB Flash Device
(SFLE = 1)
Unlocked Flash Pages
0x0000
Access limit
set according
to the Flash
security lock
byte
0x03FF
Scratchpad Area
(Data Only)
0x0000
Figure 13.1. Flash Program Memory Map
144
Rev. 1.3
0x0000
Si1000/1/2/3/4/5
The level of flash security depends on the flash access method. The three flash access methods that can
be restricted are reads, writes, and erases from the C2 debug interface, user firmware executing on
unlocked pages, and user firmware executing on locked pages. Table 13.1 summarizes the flash security
features of the Si1000/1/2/3/4/5 devices.
Table 13.1. Flash Security Summary
Action
C2 Debug
Interface
User Firmware executing from:
an unlocked page
Permitted
a locked page
Read, Write or Erase unlocked pages
(except page with Lock Byte)
Permitted
Read, Write or Erase locked pages
(except page with Lock Byte)
Not Permitted FEDR
Permitted
Read or Write page containing Lock Byte
(if no pages are locked)
Permitted
Permitted
Read or Write page containing Lock Byte
(if any page is locked)
Not Permitted FEDR
Permitted
Read contents of Lock Byte
(if no pages are locked)
Permitted
Permitted
Read contents of Lock Byte
(if any page is locked)
Not Permitted FEDR
Permitted
Erase page containing Lock Byte
(if no pages are locked)
Permitted
FEDR
FEDR
Erase page containing Lock Byte - Unlock all pages
(if any page is locked)
Only by C2DE FEDR
FEDR
Lock additional pages
(change 1s to 0s in the Lock Byte)
Not Permitted FEDR
FEDR
Unlock individual pages
(change 0s to 1s in the Lock Byte)
Not Permitted FEDR
FEDR
Read, Write or Erase Reserved Area
Not Permitted FEDR
FEDR
Permitted
Permitted
Permitted

C2DE—C2 Device Erase (Erases all flash pages including the page containing the Lock Byte)
FEDR—Not permitted; Causes Flash Error Device Reset (FERROR bit in RSTSRC is 1 after reset)
- All prohibited operations that are performed via the C2 interface are ignored (do not cause device reset).
- Locking any flash page also locks the page containing the Lock Byte.
- Once written to, the Lock Byte cannot be modified except by performing a C2 Device Erase.
- If user code writes to the Lock Byte, the Lock does not take effect until the next device reset.
- The scratchpad is locked when all other flash pages are locked.
- The scratchpad is erased when a Flash Device Erase command is performed.
Rev. 1.3
145
Si1000/1/2/3/4/5
13.4. Determining the Device Part Number at Run Time
In many applications, user software may need to determine the MCU part number at run time in order to
determine the hardware capabilities. The part number can be determined by reading the value of the flash
byte at address 0xFFFE.

The value of the flash byte at address 0xFFFE can be decoded as follows:

0xD0—Si1000
0xD1—Si1001
0xD2—Si1002
0xD3—Si1003
0xD4 - Si1004
0xD5 - Si1005
13.5. Flash Write and Erase Guidelines
Any system which contains routines which write or erase flash memory from software involves some risk
that the write or erase routines will execute unintentionally if the CPU is operating outside its specified
operating range of VDD, system clock frequency, or temperature. This accidental execution of flash modifying code can result in alteration of flash memory contents causing a system failure that is only recoverable by re-flashing the code in the device.
To help prevent the accidental modification of flash by firmware, the VDD Monitor must be enabled and
enabled as a reset source on Si100x devices for the flash to be successfully modified. If either the VDD
Monitor or the VDD Monitor reset source is not enabled, a Flash Error Device Reset will be generated when the firmware attempts to modify the flash.
The following guidelines are recommended for any system that contains routines which write or erase flash
from code.
13.5.1. VDD Maintenance and the VDD Monitor
1. If the system power supply is subject to voltage or current "spikes," add sufficient transient protection
devices to the power supply to ensure that the supply voltages listed in the Absolute Maximum Ratings
table are not exceeded.
2. Make certain that the minimum VDD rise time specification of 1 ms is met. If the system cannot meet
this rise time specification, then add an external VDD brownout circuit to the RST pin of the device that
holds the device in reset until VDD reaches the minimum device operating voltage and re-asserts RST if
VDD drops below the minimum device operating voltage.
3. Keep the on-chip VDD Monitor enabled and enable the VDD Monitor as a reset source as early in code
as possible. This should be the first set of instructions executed after the Reset Vector. For C-based
systems, this will involve modifying the startup code added by the C compiler. See your compiler
documentation for more details. Make certain that there are no delays in software between enabling the
VDD Monitor and enabling the VDD Monitor as a reset source. Code examples showing this can be
found in “AN201: Writing to Flash from Firmware," available from the Silicon Laboratories website.
Notes: On Si1000/1/2/3/4/5 devices, both the VDD Monitor and the VDD Monitor reset source must be enabled to write
or erase flash without generating a Flash Error Device Reset.

On Si1000/1/2/3/4/5 devices, both the VDD Monitor and the VDD Monitor reset source are enabled by hardware
after a power-on reset.
4. As an added precaution, explicitly enable the VDD Monitor and enable the VDD Monitor as a reset
source inside the functions that write and erase flash memory. The VDD Monitor enable instructions
should be placed just after the instruction to set PSWE to a 1, but before the flash write or erase
operation instruction.
146
Rev. 1.3
Si1000/1/2/3/4/5
5. Make certain that all writes to the RSTSRC (Reset Sources) register use direct assignment operators
and explicitly DO NOT use the bit-wise operators (such as AND or OR). For example, "RSTSRC =
0x02" is correct, but "RSTSRC |= 0x02" is incorrect.
6. Make certain that all writes to the RSTSRC register explicitly set the PORSF bit to a 1. Areas to check
are initialization code which enables other reset sources, such as the Missing Clock Detector or
Comparator, for example, and instructions which force a Software Reset. A global search on "RSTSRC"
can quickly verify this.
13.5.2. PSWE Maintenance
7. Reduce the number of places in code where the PSWE bit (b0 in PSCTL) is set to a 1. There should be
exactly one routine in code that sets PSWE to a 1 to write flash bytes and one routine in code that sets
both PSWE and PSEE both to a 1 to erase flash pages.
8. Minimize the number of variable accesses while PSWE is set to a 1. Handle pointer address updates
and loop maintenance outside the "PSWE = 1;... PSWE = 0;" area. Code examples showing this can be
found in “AN201: Writing to Flash from Firmware," available from the Silicon Laboratories website.
9. Disable interrupts prior to setting PSWE to a 1 and leave them disabled until after PSWE has been
reset to 0. Any interrupts posted during the flash write or erase operation will be serviced in priority
order after the flash operation has been completed and interrupts have been re-enabled by software.
10.Make certain that the flash write and erase pointer variables are not located in XRAM. See your
compiler documentation for instructions regarding how to explicitly locate variables in different memory
areas.
11. Add address bounds checking to the routines that write or erase flash memory to ensure that a routine
called with an illegal address does not result in modification of the flash.
13.5.3. System Clock
12.If operating from an external crystal, be advised that crystal performance is susceptible to electrical
interference and is sensitive to layout and to changes in temperature. If the system is operating in an
electrically noisy environment, use the internal oscillator or use an external CMOS clock.
13.If operating from the external oscillator, switch to the internal oscillator during flash write or erase
operations. The external oscillator can continue to run, and the CPU can switch back to the external
oscillator after the flash operation has completed.
Additional flash recommendations and example code can be found in “AN201: Writing to Flash from Firmware," available from the Silicon Laboratories website.
Rev. 1.3
147
Si1000/1/2/3/4/5
13.6. Minimizing Flash Read Current
The flash memory in the Si1000/1/2/3/4/5 devices is responsible for a substantial portion of the total digital
supply current when the device is executing code. Below are suggestions to minimize flash read current.
1. Use Idle, Suspend, or Sleep Modes while waiting for an interrupt, rather than polling the interrupt flag.
Idle Mode is particularly well-suited for use in implementing short pauses, since the wake-up time is no
more than three system clock cycles. See the Power Management chapter for details on the various
low-power operating modes.
2. Si1000/1/2/3/4/5 devices have a one-shot timer that saves power when operating at system clock
frequencies of 10 MHz or less. The one-shot timer generates a minimum-duration enable signal for the
flash sense amps on each clock cycle in which the flash memory is accessed. This allows the flash to
remain in a low power state for the remainder of the long clock cycle.
At clock frequencies above 10 MHz, the system clock cycle becomes short enough that the one-shot
timer no longer provides a power benefit. Disabling the one-shot timer at higher frequencies reduces
power consumption. The one-shot is enabled by default, and it can be disabled (bypassed) by setting
the BYPASS bit (FLSCL.6) to logic 1. To re-enable the one-shot, clear the BYPASS bit to logic 0. After
changing the BYPASS bit from 1 to 0, the third opcode byte fetched from program memory is
indeterminate. Therefore, the operation which clears the BYPASS bit should be immediately followed
by a benign 3-byte instruction whose third byte is a don't care. An example of such an instruction is a 3byte MOV that targets the FLWR register. When programming in C, the dummy value written to FLWR
should be a non-zero value to prevent the compiler from generating a 2-byte MOV instruction.
3. Flash read current depends on the number of address lines that toggle between sequential flash read
operations. In most cases, the difference in power is relatively small (on the order of 5%).
4. The flash memory is organized in rows. Each row in the Si1000/1/2/3/4/5 flash contains 128 bytes. A
substantial current increase can be detected when the read address jumps from one row in the flash
memory to another. Consider a 3-cycle loop (e.g., SJMP $, or while(1);) which straddles a 128-byte
flash row boundary. The flash address jumps from one row to another on two of every three clock
cycles. This can result in a current increase of up 30% when compared to the same 3-cycle loop
contained entirely within a single row.
5. To minimize the power consumption of small loops, it is best to locate them within a single row, if
possible. To check if a loop is contained within a flash row, divide the starting address of the first
instruction in the loop by 128. If the remainder (result of modulo operation) plus the length of the loop is
less than 127, then the loop fits inside a single flash row. Otherwise, the loop will be straddling two
adjacent flash rows. If a loop executes in 20 or more clock cycles, then the transitions from one row to
another will occur on relatively few clock cycles, and any resulting increase in operating current will be
negligible.
Note: Future 16 and 8 kB derivatives in this product family will use a flash memory that is organized in rows of 64
bytes each. To maintain code compatibility across the entire family, it is best to locate small loops within a single
64-byte segment.
148
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 13.1. PSCTL: Program Store R/W Control
Bit
7
6
5
4
3
Name
2
1
0
SFLE
PSEE
PSWE
Type
R
R
R
R
R
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page =0x0; SFR Address = 0x8F
Bit
Name
7:3
Unused
2
SFLE
Function
Read = 00000b, Write = don’t care.
Scratchpad Flash Memory Access Enable.
When this bit is set, flash MOVC reads and MOVX writes from user software are
directed to the Scratchpad flash sector. Flash accesses outside the address range
0x0000-0x03FF should not be attempted and may yield undefined results when SFLE
is set to 1.
0: Flash access from user software directed to the Program/Data Flash sector.
1: Flash access from user software directed to the Scratchpad Sector.
1
PSEE
Program Store Erase Enable.
Setting this bit (in combination with PSWE) allows an entire page of flash program
memory to be erased. If this bit is logic 1 and flash writes are enabled (PSWE is logic
1), a write to flash memory using the MOVX instruction will erase the entire page that
contains the location addressed by the MOVX instruction. The value of the data byte
written does not matter.
0: Flash program memory erasure disabled.
1: Flash program memory erasure enabled.
0
PSWE
Program Store Write Enable.
Setting this bit allows writing a byte of data to the flash program memory using the
MOVX write instruction. The flash location should be erased before writing data.
0: Writes to flash program memory disabled.
1: Writes to flash program memory enabled; the MOVX write instruction targets flash
memory.
Rev. 1.3
149
Si1000/1/2/3/4/5
SFR Definition 13.2. FLKEY: Flash Lock and Key
Bit
7
6
5
4
3
Name
FLKEY[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xB6
Bit
Name
7:0
0
2
1
0
0
0
0
Function
FLKEY[7:0] Flash Lock and Key Register.
Write:
This register provides a lock and key function for flash erasures and writes. Flash
writes and erases are enabled by writing 0xA5 followed by 0xF1 to the FLKEY register. Flash writes and erases are automatically disabled after the next write or erase is
complete. If any writes to FLKEY are performed incorrectly, or if a flash write or erase
operation is attempted while these operations are disabled, the flash will be permanently
locked from writes or erasures until the next device reset. If an application never
writes to flash, it can intentionally lock the flash by writing a non-0xA5 value to FLKEY
from software.
Read:
When read, bits 1–0 indicate the current flash lock state.
00: Flash is write/erase locked.
01: The first key code has been written (0xA5).
10: Flash is unlocked (writes/erases allowed).
11: Flash writes/erases disabled until the next reset.
150
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 13.3. FLSCL: Flash Scale
Bit
7
6
5
4
3
2
1
0
BYPASS
Name
Type
R
R/W
R
R
R
R
R
R
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xB6
Bit
Name
Function
7
Reserved
Always Write to 0.
6
BYPASS
Flash Read Timing One-Shot Bypass.
0: The one-shot determines the flash read time. This setting should be used for operating frequencies less than 10 MHz.
1: The system clock determines the flash read time. This setting should be used for
frequencies greater than 10 MHz.
5:0
Reserved
Always Write to 000000.
Note: When changing the BYPASS bit from 1 to 0, the third opcode byte fetched from program memory is
indeterminate. Therefore, the operation which clears the BYPASS bit should be immediately followed by a
benign 3-byte instruction whose third byte is a don’t care. An example of such an instruction is a 3-byte MOV
that targets the FLWR register. When programming in C, the dummy value written to FLWR should be a nonzero value to prevent the compiler from generating a 2-byte MOV instruction.
SFR Definition 13.4. FLWR: Flash Write Only
Bit
7
6
5
4
Name
FLWR[7:0]
Type
W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xE5
Bit
Name
7:0
3
2
1
0
0
0
0
0
Function
FLWR[7:0] Flash Write Only.
All writes to this register have no effect on system operation.
Rev. 1.3
151
Si1000/1/2/3/4/5
14. Power Management
Si1000/1/2/3/4/5 devices support 5 power modes: Normal, Idle, Stop, Suspend, and Sleep. The power
management unit (PMU0) allows the device to enter and wake-up from the available power modes. A brief
description of each power mode is provided in Table 14.1. Detailed descriptions of each mode can be
found in the following sections.
Table 14.1. Power Modes
Power Mode
Description
Wake-Up
Sources
Power Savings
N/A
Excellent MIPS/mW
Normal
Device fully functional
Idle
All peripherals fully functional.
Very easy to wake up.
Any Interrupt
Good
No Code Execution
Stop
Legacy 8051 low power mode.
A reset is required to wake up.
Any Reset
Good
No Code Execution
Precision Oscillator Disabled
Suspend
Similar to Stop Mode, but very fast
wake-up time and code resumes
execution at the next instruction.
SmaRTClock,
Port Match,
Comparator0,
RST pin
Very Good
No Code Execution
All Internal Oscillators Disabled
System Clock Gated
Sleep
Ultra Low Power and flexible
wake-up sources. Code resumes
execution at the next instruction.
Comparator0 only functional in
two-cell mode.
SmaRTClock,
Port Match,
Comparator0,
RST pin
Excellent
Power Supply Gated
All Oscillators except SmaRTClock Disabled
In battery powered systems, the system should spend as much time as possible in Sleep mode in order to
preserve battery life. When a task with a fixed number of clock cycles needs to be performed, the device
should switch to Normal mode, finish the task as quickly as possible, and return to Sleep mode. Idle Mode
and Suspend modes provide a very fast wake-up time; however, the power savings in these modes will not
be as much as in Sleep Mode. Stop Mode is included for legacy reasons; the system will be more power
efficient and easier to wake up when Idle, Suspend, or Sleep Mode are used.
Although switching power modes is an integral part of power management, enabling/disabling individual
peripherals as needed will help lower power consumption in all power modes. Each analog peripheral can
be disabled when not in use or placed in a low power mode. Digital peripherals such as timers or serial
busses draw little power whenever they are not in use. Digital peripherals draw no power in Sleep Mode.
152
Rev. 1.3
Si1000/1/2/3/4/5
14.1. Normal Mode
The MCU is fully functional in Normal Mode. Figure 14.1 shows the on-chip power distribution to various
peripherals. There are three supply voltages powering various sections of the chip: VBAT, VDD/DC+, and
the 1.8 V internal core supply. VREG0, PMU0 and the SmaRTClock are always powered directly from the
VBAT pin. All analog peripherals are directly powered from the VDD/DC+ pin, which is an output in one-cell
mode and an input in two-cell mode. All digital peripherals and the CIP-51 core are powered from the 1.8 V
internal core supply. The RAM is also powered from the core supply in Normal mode.
VBAT
One-cell: 0.9 to 1.8 V
Two-cell: 1.8 to 3.6 V
DC0
VDD/DC+
One-cell or Two-cell: 1.8 to 3.6 V
Note: VDD/DC+ must be > VBAT
1.9 V
typical
GPIO
Analog Peripherals
One-Cell Active/
Idle/Stop/Suspend
One-Cell Sleep
VREF
VREG0
A
M
U
X
IREF0
10-bit
300 ksps
ADC
+
TEMP
SENSOR
Sleep
Active/Idle/
Stop/Suspend 1.8 V
+
-
VOLTAGE
COMPARATORS
Digital Peripherals
UART
PMU0
CIP-51
Core
SmaRTClock
RAM
Flash
SPI
Timers
SMBus
Figure 14.1. Si1000/1/2/3/4/5 Power Distribution
Rev. 1.3
153
Si1000/1/2/3/4/5
14.2. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the CIP-51 to halt the CPU and enter Idle mode as soon
as the instruction that sets the bit completes execution. All internal registers and memory maintain their
original data. All analog and digital peripherals can remain active during Idle mode.
Note: To ensure the MCU enters a low power state upon entry into Idle Mode, the one-shot circuit should be enabled
by clearing the BYPASS bit (FLSCL.6) to logic 0. See the note in SFR Definition 13.3. FLSCL: Flash Scale for
more information on how to properly clear the BYPASS bit.
Idle mode is terminated when an enabled interrupt is asserted or a reset occurs. The assertion of an
enabled interrupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU to resume
operation. The pending interrupt will be serviced and the next instruction to be executed after the return
from interrupt (RETI) will be the instruction immediately following the one that set the Idle Mode Select bit.
If Idle mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence
and begins program execution at address 0x0000.
If enabled, the Watchdog Timer (WDT) will eventually cause an internal watchdog reset and thereby terminate the Idle mode. This feature protects the system from an unintended permanent shutdown in the event
of an inadvertent write to the PCON register. If this behavior is not desired, the WDT may be disabled by
software prior to entering the Idle mode if the WDT was initially configured to allow this operation. This provides the opportunity for additional power savings, allowing the system to remain in the Idle mode indefinitely, waiting for an external stimulus to wake up the system. Refer to Section “18.6. PCA Watchdog Timer
Reset” on page 183 for more information on the use and configuration of the WDT.
14.3. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the CIP-51 to enter Stop mode as soon as the instruction that sets the bit completes execution. In Stop mode the precision internal oscillator and CPU are
stopped; the state of the low power oscillator and the external oscillator circuit is not affected. Each analog
peripheral (including the external oscillator circuit) may be shut down individually prior to entering Stop
Mode. Stop mode can only be terminated by an internal or external reset. On reset, the CIP-51 performs
the normal reset sequence and begins program execution at address 0x0000.
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode.
The Missing Clock Detector should be disabled if the CPU is to be put to in STOP mode for longer than the
MCD timeout of 100 µs.
Stop Mode is a legacy 8051 power mode; it will not result in optimal power savings. Sleep or Suspend
mode will provide more power savings if the MCU needs to be inactive for a long period of time.
On Si1000/1/2/3/4/5 devices, the Precision Oscillator Bias is not automatically disabled and should be disabled by software to achieve the lowest possible Stop mode current.
Note: To ensure the MCU enters a low power state upon entry into Stop Mode, the one-shot circuit should be enabled
by clearing the BYPASS bit (FLSCL.6) to logic 0. See the note in SFR Definition 13.3. FLSCL: Flash Scale for
more information on how to properly clear the BYPASS bit.
154
Rev. 1.3
Si1000/1/2/3/4/5
14.4. Suspend Mode
Setting the Suspend Mode Select bit (PMU0CF.6) causes the system clock to be gated off and all internal
oscillators disabled. All digital logic (timers, communication peripherals, interrupts, CPU, etc.) stops
functioning until one of the enabled wake-up sources occurs.
Important Notes:

When entering Suspend Mode, the global clock divider must be set to "divide by 1" by setting
CLKDIV[2:0] = 000b in the CLKSEL register.
 The one-shot circuit should be enabled by clearing the BYPASS bit (FLSCL.6) to logic 0. See the
note in SFR Definition 13.3. FLSCL: Flash Scale for more information on how to properly clear
the BYPASS bit.
 Upon wake-up from suspend mode, PMU0 requires two system clocks in order to update the
PMU0CF wake-up flags. All flags will read back a value of 0 during the first two system clocks
following a wake-up from suspend mode.
 The system clock source must be set to the low power internal oscillator or the precision
oscillator prior to entering suspend mode.
The following wake-up sources can be configured to wake the device from suspend mode:
SmaRTClock Oscillator Fail
 SmaRTClock Alarm
 Port Match Event
 Comparator0 Rising Edge
In addition, a noise glitch on RST that is not long enough to reset the device will cause the device to exit
suspend. In order for the MCU to respond to the pin reset event, software must not place the device back
into suspend mode for a period of 15 µs. The PMU0CF register may be checked to determine if the wakeup was due to a falling edge on the /RST pin. If the wake-up source is not due to a falling edge on RST,
there is no time restriction on how soon software may place the device back into suspend mode. A 4.7 k
pullup resistor to VDD_MCU/DC+ is recommend for RST to prevent noise glitches from waking the device.

14.5. Sleep Mode
Setting the Sleep Mode Select bit (PMU0CF.6) turns off the internal 1.8 V regulator (VREG0) and switches
the power supply of all on-chip RAM to the VDD_MCU pin (see Figure 14.1). Power to most digital logic on
the chip is disconnected; only PMU0 and the SmaRTClock remain powered. Analog peripherals remain
powered. The Comparators remain functional when the device enters sleep mode. All other analog peripherals (ADC0, IREF0, External Oscillator, etc.) should be disabled prior to entering sleep mode. The system
clock source must be set to the low power internal oscillator or the precision oscillator prior to entering
sleep mode.
Important Notes:

When entering Sleep Mode, the global clock divider must be set to "divide by 1" by setting
CLKDIV[2:0] = 000b in the CLKSEL register.
 Any write to PMU0CF which places the device in sleep mode should be immediately followed by two
NOP instructions. Software that does not place two NOP instructions immediately following the write to
PMU0CF should continue to behave the same way as during software development.
GPIO pins configured as digital outputs will retain their output state during sleep mode. In two-cell mode,
they will maintain the same current drive capability in sleep mode as they have in normal mode. In one-cell
mode, the VDD_MCU/DC+ supply will drop to the level of VBAT, which will reduce the output high-voltage
level and the source and sink current drive capability.
GPIO pins configured as digital inputs can be used during sleep mode as wakeup sources using the port
match feature. In two-cell mode, they will maintain the same input level specifications in sleep mode as
they have in normal mode. In one-cell mode, the VDD supply will drop to the level of VBAT, which will lower
the switching threshold and increase the propagation delay.
Rev. 1.3
155
Si1000/1/2/3/4/5
Note: By default, the VDD/DC+ supply is connected to VBAT upon entry into Sleep Mode (one-cell mode). If the
VDDSLP bit (DC0CF.1) is set to logic 1, the VDD/DC+ supply will float in Sleep Mode. This allows the
decoupling capacitance on the VDD/DC+ supply to maintain the supply rail until the capacitors are discharged.
For relatively short sleep intervals, this can result in substantial power savings because the decoupling
capacitance is not continuously charged and discharged.
RAM and SFR register contents are preserved in sleep mode as long as the voltage on VBAT (or
VDD_MCU on Si1000/1/2/3 devices) does not fall below VPOR. The PC counter and all other volatile state
information is preserved allowing the device to resume code execution upon waking up from sleep mode.
The following wake-up sources can be configured to wake the device from sleep mode:
SmaRTClock Oscillator Fail
 SmaRTClock Alarm
 Port Match Event
 Comparator0 Rising Edge

The Comparator0 Rising Edge wakeup is only valid in two-cell mode. The comparator requires a supply
voltage of at least 1.8 V to operate properly.
In addition, any falling edge on RST (due to a pin reset or a noise glitch) will cause the device to exit sleep
mode. In order for the MCU to respond to the pin reset event, software must not place the device back into
sleep mode for a period of 15 µs. The PMU0CF register may be checked to determine if the wake-up was
due to a falling edge on the RST pin. If the wake-up source is not due to a falling edge on RST, there is no
time restriction on how soon software may place the device back into sleep mode. A 4.7 k pullup resistor
to VDD_MCU/DC+ is recommend for RST to prevent noise glitches from waking the device.
14.6. Configuring Wakeup Sources
Before placing the device in a low power mode, one or more wakeup sources should be enabled so that
the device does not remain in the low power mode indefinitely. For Idle Mode, this includes enabling any
interrupt. For stop mode, this includes enabling any reset source or relying on the RST pin to reset the
device.
Wake-up sources for suspend and sleep modes are configured through the PMU0CF register. Wake-up
sources are enabled by writing 1 to the corresponding wake-up source enable bit. Wake-up sources must
be re-enabled each time the device is placed in suspend or sleep mode, in the same write that places the
device in the low power mode.
The reset pin is always enabled as a wake-up source. On the falling edge of RST, the device will be
awaken from sleep mode. The device must remain awake for more than 15 µs in order for the reset to take
place.
14.7. Determining the Event that Caused the Last Wakeup
When waking from Idle Mode, the CPU will vector to the interrupt which caused it to wake up. When waking from Stop mode, the RSTSRC register may be read to determine the cause of the last reset.
Upon exit from Suspend or Sleep mode, the wake-up flags in the PMU0CF register can be read to determine the event which caused the device to wake up. After waking up, the wake-up flags will continue to be
updated if any of the wake-up events occur. Wake-up flags are always updated, even if they are not
enabled as wake-up sources.
All wake-up flags enabled as wake-up sources in PMU0CF must be cleared before the device can enter
suspend or sleep mode. After clearing the wake-up flags, each of the enabled wake-up events should be
checked in the individual peripherals to ensure that a wake-up event did not occur while the wake-up flags
were being cleared.
156
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 14.1. PMU0CF: Power Management Unit Configuration1,2
Bit
7
6
5
4
3
2
1
0
Name
SLEEP
SUSPEND
CLEAR
RSTWK
RTCFWK
RTCAWK
PMATWK
CPT0WK
Type
W
W
W
R
R/W
R/W
R/W
R/W
Reset
0
0
0
Varies
Varies
Varies
Varies
Varies
SFR Page = 0x0; SFR Address = 0xB5
Bit
Name
Description
7
SLEEP
6
SUSPEND
5
Write
Read
Sleep Mode Select
Writing 1 places the
device in Sleep Mode.
N/A
Suspend Mode Select
Writing 1 places the
device in Suspend Mode.
N/A
CLEAR
Wake-up Flag Clear
Writing 1 clears all wakeup flags.
N/A
4
RSTWK
Reset Pin Wake-up Flag
N/A
Set to 1 if a falling edge has
been detected on RST.
3
RTCFWK
SmaRTClock Oscillator
Fail Wake-up Source
Enable and Flag
0: Disable wake-up on
SmaRTClock Osc. Fail.
1: Enable wake-up on
SmaRTClock Osc. Fail.
Set to 1 if the SmaRTClock
Oscillator has failed.
2
RTCAWK
SmaRTClock Alarm
Wake-up Source Enable
and Flag
0: Disable wake-up on
SmaRTClock Alarm.
1: Enable wake-up on
SmaRTClock Alarm.
Set to 1 if a SmaRTClock
Alarm has occurred.
1
PMATWK
Port Match Wake-up
Source Enable and Flag
0: Disable wake-up on
Port Match Event.
1: Enable wake-up on 
Port Match Event.
Set to 1 if a Port Match
Event has occurred.
0
CPT0WK
Comparator0 Wake-up
Source Enable and Flag
0: Disable wake-up on
Comparator0 rising edge.
1: Enable wake-up on
Comparator0 rising edge.
Set to 1 if Comparator0 rising edge caused the last
wake-up.
Notes:
1. Read-modify-write operations (ORL, ANL, etc.) should not be used on this register. Wake-up sources must be
re-enabled each time the SLEEP or SUSPEND bits are written to 1.
2. The Low Power Internal Oscillator cannot be disabled and the MCU cannot be placed in Suspend or Sleep
Mode if any wake-up flags are set to 1. Software should clear all wake-up sources after each reset and after
each wake-up from Suspend or Sleep Modes.
Rev. 1.3
157
Si1000/1/2/3/4/5
SFR Definition 14.2. PCON: Power Management Control Register
Bit
7
6
5
4
3
2
1
0
Name
GF[5:0]
STOP
IDLE
Type
R/W
W
W
0
0
Reset
0
0
0
0
SFR Page = All Pages; SFR Address = 0x87
Bit
Name
Description
7:2
GF[5:0]
1
0
0
Write
Read
General Purpose Flags
Sets the logic value.
Returns the logic value.
STOP
Stop Mode Select
Writing 1 places the
device in Stop Mode.
N/A
IDLE
Idle Mode Select
Writing 1 places the
device in Idle Mode.
N/A
14.8. Power Management Specifications
See Table 4.5 on page 57 for detailed Power Management Specifications.
158
0
Rev. 1.3
Si1000/1/2/3/4/5
15. Cyclic Redundancy Check Unit (CRC0)
Si1000/1/2/3/4/5 devices include a cyclic redundancy check unit (CRC0) that can perform a CRC using a
16-bit or 32-bit polynomial. CRC0 accepts a stream of 8-bit data written to the CRC0IN register. CRC0
posts the 16-bit or 32-bit result to an internal register. The internal result register may be accessed indirectly using the CRC0PNT bits and CRC0DAT register, as shown in Figure 15.1. CRC0 also has a bit
reverse register for quick data manipulation.
8
CRC0CN
CRC0IN
8
Automatic CRC
Controller
Flash
Memory
CRC0AUTO
CRC0SEL
CRC0INIT
CRC0VAL
CRC0PNT1
CRC0PNT0
CRC Engine
CRC0CNT
32
RESULT
CRC0FLIP
Write
8
8
8
8
4 to 1 MUX
8
CRC0DAT
CRC0FLIP
Read
Figure 15.1. CRC0 Block Diagram
15.1. 16-bit CRC Algorithm
The Si1000/1/2/3/4/5 CRC unit calculates the 16-bit CRC MSB-first, using a poly of 0x1021. The following
describes the 16-bit CRC algorithm performed by the hardware:
1. XOR the input with the most-significant bits of the current CRC result. If this is the first iteration of the
CRC unit, the current CRC result will be the set initial value (0x0000 or 0xFFFF).
2a. If the MSB of the CRC result is set, left-shift the CRC result and XOR the result with the selected
polynomial (0x1021).
2b. If the MSB of the CRC result is not set, left-shift the CRC result.
Repeat Steps 2a/2b for the number of input bits (8). The algorithm is also described in the following example.
The 16-bit Si1000/1/2/3/4/5 CRC algorithm can be described by the following code:
unsigned short UpdateCRC (unsigned short CRC_acc, unsigned char CRC_input)
{
unsigned char i;
// loop counter
#define POLY 0x1021
Rev. 1.3
159
Si1000/1/2/3/4/5
// Create the CRC "dividend" for polynomial arithmetic (binary arithmetic
// with no carries)
CRC_acc = CRC_acc ^ (CRC_input << 8);
// "Divide" the poly into the dividend using CRC XOR subtraction
// CRC_acc holds the "remainder" of each divide
//
// Only complete this division for 8 bits since input is 1 byte
for (i = 0; i < 8; i++)
{
// Check if the MSB is set (if MSB is 1, then the POLY can "divide"
// into the "dividend")
if ((CRC_acc & 0x8000) == 0x8000)
{
// if so, shift the CRC value, and XOR "subtract" the poly
CRC_acc = CRC_acc << 1;
CRC_acc ^= POLY;
}
else
{
// if not, just shift the CRC value
CRC_acc = CRC_acc << 1;
}
}
// Return the final remainder (CRC value)
return CRC_acc;
}
The following table lists several input values and the associated outputs using the 16-bit Si1000/1/2/3/4/5
CRC algorithm:
Table 15.1. Example 16-bit CRC Outputs
160
Input
Output
0x63
0xBD35
0x8C
0xB1F4
0x7D
0x4ECA
0xAA, 0xBB, 0xCC
0x6CF6
0x00, 0x00, 0xAA, 0xBB, 0xCC
0xB166
Rev. 1.3
Si1000/1/2/3/4/5
15.2. 32-bit CRC Algorithm
The Si1000 CRC unit calculates the 32-bit CRC using a poly of 0x04C11DB7. The CRC-32 algorithm is
"reflected", meaning that all of the input bytes and the final 32-bit output are bit-reversed in the processing
engine. The following is a description of a simplified CRC algorithm that produces results identical to the
hardware:
Step 1. XOR the least-significant byte of the current CRC result with the input byte. If this is the
first iteration of the CRC unit, the current CRC result will be the set initial value
(0x00000000 or 0xFFFFFFFF).
Step 2. Right-shift the CRC result.
Step 3. If the LSB of the CRC result is set, XOR the CRC result with the reflected polynomial
(0xEDB88320).
Step 4. Repeat at Step 2 for the number of input bits (8).
For example, the 32-bit Si1000 CRC algorithm can be described by the following code:
unsigned long UpdateCRC (unsigned long CRC_acc, unsigned char CRC_input)
{
unsigned char i; // loop counter
#define POLY 0xEDB88320 // bit-reversed version of the poly 0x04C11DB7
// Create the CRC "dividend" for polynomial arithmetic (binary arithmetic
// with no carries)
CRC_acc = CRC_acc ^ CRC_input;
// "Divide" the poly into the dividend using CRC XOR subtraction
// CRC_acc holds the "remainder" of each divide
//
// Only complete this division for 8 bits since input is 1 byte
for (i = 0; i < 8; i++)
{
// Check if the MSB is set (if MSB is 1, then the POLY can "divide"
// into the "dividend")
if ((CRC_acc & 0x00000001) == 0x00000001)
{
// if so, shift the CRC value, and XOR "subtract" the poly
CRC_acc = CRC_acc >> 1;
CRC_acc ^= POLY;
}
else
{
// if not, just shift the CRC value
CRC_acc = CRC_acc >> 1;
}
}
// Return the final remainder (CRC value)
return CRC_acc;
}
The following table lists several input values and the associated outputs using the 32-bit Si1000 CRC algorithm (an initial value of 0xFFFFFFFF is used):
Rev. 1.3
161
Si1000/1/2/3/4/5
Table 15.2. Example 32-bit CRC Outputs
162
Input
Output
0x63
0xF9462090
0xAA, 0xBB, 0xCC
0x41B207B3
0x00, 0x00, 0xAA, 0xBB, 0xCC
0x78D129BC
Rev. 1.3
Si1000/1/2/3/4/5
15.3. Preparing for a CRC Calculation
To prepare CRC0 for a CRC calculation, software should select the desired polynomial and set the initial
value of the result. Two polynomials are available: 0x1021 (16-bit) and 0x04C11DB7 (32-bit). The CRC0
result may be initialized to one of two values: 0x00000000 or 0xFFFFFFFF. The following steps can be
used to initialize CRC0.
1. Select a polynomial (Set CRC0SEL to 0 for 32-bit or 1 for 16-bit).
2. Select the initial result value (Set CRC0VAL to 0 for 0x00000000 or 1 for 0xFFFFFFFF).
3. Set the result to its initial value (Write 1 to CRC0INIT).
15.4. Performing a CRC Calculation
Once CRC0 is initialized, the input data stream is sequentially written to CRC0IN, one byte at a time. The
CRC0 result is automatically updated after each byte is written. The CRC engine may also be configured to
automatically perform a CRC on one or more Flash sectors. The following steps can be used to automatically perform a CRC on Flash memory.
1. Prepare CRC0 for a CRC calculation as shown above.
2. Write the index of the starting page to CRC0AUTO.
3. Set the AUTOEN bit in CRC0AUTO.
4. Write the number of Flash sectors to perform in the CRC calculation to CRC0CNT. 
Note: Each Flash sector is 1024 bytes.
5. Write any value to CRC0CN (or OR its contents with 0x00) to initiate the CRC calculation. The CPU will
not execute code any additional code until the CRC operation completes.
6. After initiating an automatic CRC calculation, the third opcode byte fetched from program memory is
indeterminate. Therefore, writes to CRC0CN that initiate a CRC operation must be immediately
followed by a benign 3-byte instruction whose third byte is a don't care. An example of such an
instruction is a 3-byte MOV that targets the CRC0FLIP register. When programming in C, the dummy
value written to CRC0FLIP should be a non-zero value to prevent the compiler from generating a 2-byte
MOV instruction.
7. Clear the AUTOEN bit in CRC0AUTO.
8. Read the CRC result using the procedure below.
15.5. Accessing the CRC0 Result
The internal CRC0 result is 32-bits (CRC0SEL = 0b) or 16-bits (CRC0SEL = 1b). The CRC0PNT bits
select the byte that is targeted by read and write operations on CRC0DAT and increment after each read or
write. The calculation result will remain in the internal CR0 result register until it is set, overwritten, or additional data is written to CRC0IN.
Rev. 1.3
163
Si1000/1/2/3/4/5
SFR Definition 15.1. CRC0CN: CRC0 Control
Bit
7
6
5
4
3
2
CRC0SEL CRC0INIT CRC0VAL
Name
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
SFR Page = 0xF; SFR Address = 0x92
Bit
Name
7:5
Unused
4
CRC0SEL
1
0
CRC0PNT[1:0]
R/W
0
0
Function
Read = 000b; Write = Don’t Care.
CRC0 Polynomial Select Bit.
This bit selects the CRC0 polynomial and result length (32-bit or 16-bit).
0: CRC0 uses the 32-bit polynomial 0x04C11DB7 for calculating the CRC result.
1: CRC0 uses the 16-bit polynomial 0x1021 for calculating the CRC result.
3
CRC0INIT
CRC0 Result Initialization Bit.
Writing a 1 to this bit initializes the entire CRC result based on CRC0VAL.
2
CRC0VAL
CRC0 Set Value Initialization Bit.
This bit selects the set value of the CRC result.
0: CRC result is set to 0x00000000 on write of 1 to CRC0INIT.
1: CRC result is set to 0xFFFFFFFF on write of 1 to CRC0INIT.
1:0 CRC0PNT[1:0] CRC0 Result Pointer.
Specifies the byte of the CRC result to be read/written on the next access to
CRC0DAT. The value of these bits will auto-increment upon each read or write.
For CRC0SEL = 0:
00: CRC0DAT accesses bits 7–0 of the 32-bit CRC result.
01: CRC0DAT accesses bits 15–8 of the 32-bit CRC result.
10: CRC0DAT accesses bits 23–16 of the 32-bit CRC result.
11: CRC0DAT accesses bits 31–24 of the 32-bit CRC result.
For CRC0SEL = 1:
00: CRC0DAT accesses bits 7–0 of the 16-bit CRC result.
01: CRC0DAT accesses bits 15–8 of the 16-bit CRC result.
10: CRC0DAT accesses bits 7–0 of the 16-bit CRC result.
11: CRC0DAT accesses bits 15–8 of the 16-bit CRC result.
Note: Upon initiation of an automatic CRC calculation, the third opcode byte fetched from program memory is
indeterminate. Therefore, writes to CRC0CN that initiate a CRC operation must be immediately followed by a
benign 3-byte instruction whose third byte is a don’t care. An example of such an instruction is a 3-byte MOV
that targets the CRC0FLIP register. When programming in ‘C’, the dummy value written to CRC0FLIP should
be a non-zero value to prevent the compiler from generating a 2-byte MOV instruction.
164
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 15.2. CRC0IN: CRC0 Data Input
Bit
7
6
5
4
3
Name
CRC0IN[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0xF; SFR Address = 0x93
Bit
Name
7:0
CRC0IN[7:0]
2
1
0
0
0
0
Function
CRC0 Data Input.
Each write to CRC0IN results in the written data being computed into the existing
CRC result according to the CRC algorithm described in Section 15.1
SFR Definition 15.3. CRC0DAT: CRC0 Data Output
Bit
7
6
5
4
3
Name
CRC0DAT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0xF; SFR Address = 0x91
Bit
Name
0
2
1
0
0
0
0
Function
7:0 CRC0DAT[7:0] CRC0 Data Output.
Each read or write performed on CRC0DAT targets the CRC result bits pointed to
by the CRC0 Result Pointer (CRC0PNT bits in CRC0CN).
Rev. 1.3
165
Si1000/1/2/3/4/5
SFR Definition 15.4. CRC0AUTO: CRC0 Automatic Control
Bit
7
6
Name
AUTOEN
CRCDONE
5
4
3
2
1
CRC0ST[5:0]
R/W
Type
Reset
0
1
0
AUTOEN
R/W
0
SFR Page = 0xF; SFR Address = 0x96
Bit
Name
7
0
0
0
0
0
Function
Automatic CRC Calculation Enable.
When AUTOEN is set to 1, any write to CRC0CN will initiate an automatic CRC
starting at Flash sector CRC0ST and continuing for CRC0CNT sectors.
6
CRCDONE
CRCDONE Automatic CRC Calculation Complete.
Set to '0' when a CRC calculation is in progress. Note that code execution is
stopped during a CRC calculation, therefore reads from firmware will always
return '1'.
5:0
CRC0ST[5:0]
Automatic CRC Calculation Starting Flash Sector.
These bits specify the Flash sector to start the automatic CRC calculation. The
starting address of the first Flash sector included in the automatic CRC calculation
is CRC0ST x 1024.
SFR Definition 15.5. CRC0CNT: CRC0 Automatic Flash Sector Count
Bit
7
6
5
4
1
R/W
Type
Reset
0
0
0
0
SFR Page = 0xF; SFR Address = 0x97
Bit
Name
5:0
2
0
CRC0CNT[5:0]
Name
7:6
3
Unused
R/W
0
0
0
0
Function
Read = 00b; Write = Don’t Care.
CRC0CNT[5:0] Automatic CRC Calculation Flash Sector Count.
These bits specify the number of Flash sectors to include in an automatic CRC
calculation. The starting address of the last Flash sector included in the automatic
CRC calculation is (CRC0ST+CRC0CNT) x 1024.
166
Rev. 1.3
Si1000/1/2/3/4/5
15.6. CRC0 Bit Reverse Feature
CRC0 includes hardware to reverse the bit order of each bit in a byte as shown in Figure 15.2. Each byte
of data written to CRC0FLIP is read back bit reversed. For example, if 0xC0 is written to CRC0FLIP, the
data read back is 0x03. Bit reversal is a useful mathematical function used in algorithms such as the FFT.
CRC0FLIP
Write
CRC0FLIP
Read
Figure 15.2. Bit Reverse Register
SFR Definition 15.6. CRC0FLIP: CRC0 Bit Flip
Bit
7
6
5
4
3
Name
CRC0FLIP[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0xF; SFR Address = 0x95
Bit
Name
7:0
CRC0FLIP[7:0]
0
2
1
0
0
0
0
Function
CRC0 Bit Flip.
Any byte written to CRC0FLIP is read back in a bit-reversed order, i.e. the written
LSB becomes the MSB. For example:
If 0xC0 is written to CRC0FLIP, the data read back will be 0x03.
If 0x05 is written to CRC0FLIP, the data read back will be 0xA0.
Rev. 1.3
167
Si1000/1/2/3/4/5
16. On-Chip DC-DC Converter (DC0)
Si1004/5 devices include an on-chip dc-dc converter to allow operation from a single cell battery with a
supply voltage as low as 0.9 V. The dc-dc converter is a switching boost converter with an input voltage
range of 0.9 to 1.8 V and a programmable output voltage range of 1.8 to 3.3 V. The default output voltage
is 1.9 V. The dc-dc converter can supply the system with up to 65 mW of regulated power (or up to
100 mW in some applications) and can be used for powering other devices in the system. This allows the
most flexibility when interfacing to sensors and other analog signals which typically require a higher supply
voltage than a single-cell battery can provide.
Figure 16.1 shows a block diagram of the dc-dc converter. During normal operation in the first half of the
switching cycle, the Duty Cycle Control switch is closed and the Diode Bypass switch is open. Since the
output voltage is higher than the voltage at the DCEN pin, no current flows through the diode and the load
is powered from the output capacitor. During this stage, the DCEN pin is connected to ground through the
Duty Cycle Control switch, generating a positive voltage across the inductor and forcing its current to ramp
up.
In the second half of the switching cycle, the Duty Cycle control switch is opened and the Diode Bypass
switch is closed. This connects DCEN directly to VDD_MCU/DC+ and forces the inductor current to charge
the output capacitor. Once the inductor transfers its stored energy to the output capacitor, the Duty Cycle
Control switch is closed, the Diode Bypass switch is opened, and the cycle repeats.
The dc-dc converter has a built in voltage reference and oscillator, and will automatically limit or turn off the
switching activity in case the peak inductor current rises beyond a safe limit or the output voltage rises
above the programmed target value. This allows the dc-dc converter output to be safely overdriven by a
secondary power source (when available) in order to preserve battery life. The dc-dc converter’s settings
can be modified using SFR registers which provide the ability to change the target output voltage, oscillator
frequency or source, Diode Bypass switch resistance, peak inductor current, and minimum duty cycle.
DC/DC Converter
VBAT
VDD_MCU/DC+
0.68 uH
DCEN
Diode
Bypass
4.7 uF
Duty
Cycle
Control
GND/VBAT-
Control Logic
DC0CN
Voltage
Reference
DC0CF
DC/DC
Oscillator
Lparasitic
Lparasitic
1uF
GND_MCU/DC-
Figure 16.1. DC-DC Converter Block Diagram
168
Rev. 1.3
Iload
Cload
Si1000/1/2/3/4/5
16.1. Startup Behavior
On initial power-on, the dc-dc converter outputs a constant 50% duty cycle until there is sufficient voltage
on the output capacitor to maintain regulation. The size of the output capacitor and the amount of load current present during startup will determine the length of time it takes to charge the output capacitor.
During initial power-on reset, the maximum peak inductor current threshold, which triggers the overcurrent
protection circuit, is set to approximately 125 mA. This generates a “soft-start” to limit the output voltage
slew rate and prevent excessive in-rush current at the output capacitor. In order to ensure reliable startup
of the dc-dc converter, the following restrictions have been imposed:
•
The maximum dc load current allowed during startup is given in Table 4.15 on page 65. If the dc-dc
converter is powering external sensors or devices through the VDD_MCU/DC+ pin or through GPIO
pins, then the current supplied to these sensors or devices is counted towards this limit. The in-rush
current into capacitors does not count towards this limit.
•
The maximum total output capacitance is given in Table 4.15 on page 65. This value includes the
required 1 µF ceramic output capacitor and any additional capacitance connected to the
VDD_MCU/DC+ pin.

Once initial power-on is complete, the peak inductor current limit can be increased by software as shown in
Table 16.1. Limiting the peak inductor current can allow the device to start up near the battery’s end of life.
.
Table 16.1. IPeak Inductor Current Limit Settings
SWSEL
ILIMIT
Peak Current (mA)
1
0
100
0
0
125
1
1
250
0
1
500
The peak inductor current is dependent on several factors including the dc load current and can be estimated using following equation:
I PK =
2 I LOAD  VDD/DC+ – VBAT 
-----------------------------------------------------------------------------------------efficiency  inductance  frequency
efficiency = 0.80
inductance = 0.68 µH
frequency = 2.4 MHz
Rev. 1.3
169
Si1000/1/2/3/4/5
16.2. High Power Applications
The dc-dc converter is designed to provide the system with 65 mW of output power, however, it can safely
provide up to 100 mW of output power without any risk of damage to the device. For high power applications, the system should be carefully designed to prevent unwanted VBAT and VDD_MCU/DC+ Supply
Monitor resets, which are more likely to occur when the dc-dc converter output power exceeds 65mW. In
addition, output power above 65 mW causes the dc-dc converter to have relaxed output regulation, high
output ripple and more analog noise. At high output power, an inductor with low DC resistance should be
chosen in order to minimize power loss and maximize efficiency.
The combination of high output power and low input voltage will result in very high peak and average
inductor currents. If the power supply has a high internal resistance, the transient voltage on the VBAT terminal could drop below 0.9 V and trigger a VBAT Supply Monitor Reset, even if the open-circuit voltage is
well above the 0.9 V threshold. While this problem is most often associated with operation from very small
batteries or batteries that are near the end of their useful life, it can also occur when using bench power
supplies that have a slow transient response; the supply’s display may indicate a voltage above 0.9 V, but
the minimum voltage on the VBAT pin may be lower. A similar problem can occur at the output of the dc-dc
converter: using the default low current limit setting (125 mA) can trigger VDD Supply Monitor resets if there
is a high transient load current, particularly if the programmed output voltage is at or near 1.8 V.
16.3. Pulse Skipping Mode
The dc-dc converter allows the user to set the minimum pulse width such that if the duty cycle needs to
decrease below a certain width in order to maintain regulation, an entire "clock pulse" will be skipped.
Pulse skipping can provide substantial power savings, particularly at low values of load current. The converter will continue to maintain a minimum output voltage at its programmed value when pulse skipping is
employed, though the output voltage ripple can be higher. Another consideration is that the dc-dc will operate with pulse-frequency modulation rather than pulse-width modulation, which makes the switching frequency spectrum less predictable; this could be an issue if the dc-dc converter is used to power a radio.
Figure 4.5 and Figure 4.6 on page 48 and page 49 show the effect of pulse skipping on power consumption.
16.4. Enabling the DC-DC Converter
On power-on reset, the state of the DCEN pin is sampled to determine if the device will power up in onecell or two-cell mode. In two-cell mode, the dc-dc converter always remains disabled. In one-cell mode, the
dc-dc converter remains disabled in Sleep Mode, and enabled in all other power modes. See Section
“14. Power Management” on page 152 for complete details on available power modes.
The dc-dc converter is enabled (one-cell mode) in hardware by placing a 0.68 µH inductor between DCEN
and VBAT. The dc-dc converter is disabled (two-cell mode) by shorting DCEN directly to GND. The DCEN
pin should never be left floating. Note that the device can only switch between one-cell and two-cell mode
during a power-on reset. See Section “18. Reset Sources” on page 178 for more information regarding
reset behavior.
Figure 16.2 shows the two dc-dc converter configuration options.
170
Rev. 1.3
Si1000/1/2/3/4/5
0.68 uH
DC-DC Converter
Enabled
0.9 to 1.8 V 
Supply Voltage
VBAT GND/VBAT- DCEN
(one-cell mode)
DC-DC Converter
Disabled
1 uF
4.7 uF
VBAT GND/VBAT- DCEN
1.8 to 3.6 V 
Supply Voltage
GND_MCU/
VDD_MCU/ DCDC+
GND_MCU/
DCVDD_MCU/
DC+
(two-cell mode)
Figure 16.2. DC-DC Converter Configuration Options
When the dc-dc converter “Enabled” configuration (one-cell mode) is chosen, the following guidelines
apply:





In most cases, the GND/VBAT– pin should not be externally connected to GND.
The 0.68 µH inductor should be placed as close as possible to the DCEN pin for maximum efficiency.
The 4.7 µF capacitor should be placed as close as possible to the inductor.
The current loop including GND/VBAT–, the 4.7 µF capacitor, the 0.68 µH inductor and the DCEN pin
should be made as short as possible to minimize capacitance.
The PCB traces connecting VDD_MCU/DC+ to the output capacitor and the output capacitor to
GND_MCU/DC– should be as short and as thick as possible in order to minimize parasitic inductance.
Rev. 1.3
171
Si1000/1/2/3/4/5
16.5. Minimizing Power Supply Noise
To minimize noise on the power supply lines, the GND/VBAT– and GND_MCU/DC- pins should be kept
separate, as shown in Figure 16.2; GND_MCU/DC- should be connected to the pc board ground plane.
The large decoupling capacitors in the input and output circuits ensure that each supply is relatively quiet
with respect to its own ground. However, connecting a circuit element "diagonally" (e.g., connecting an
external chip between VDD_MCU/DC+ and GND/VBAT-, or between VBAT and GND_MCU/DC-) can
result in high supply noise across that circuit element.
To accommodate situations in which ADC0 is sampling a signal that is referenced to one of the external
grounds, we recommend using the Analog Ground Reference (P0.1/AGND) option described in Section
5.12. This option prevents any voltage differences between the internal chip ground and the external
grounds from modulating the ADC input signal. If this option is enabled, the P0.1 pin should be tied to the
ground reference of the external analog input signal. When using the ADC with the dc-dc converter, we
also recommend enabling the SYNC bit in the DC0CN register to minimize interference.
These general guidelines provide the best performance in most applications, though some situations may
benefit from experimentation to eliminate any residual noise issues. Examples might include tying the
grounds together, using additional low-inductance decoupling caps in parallel with the recommended ones,
investigating the effects of different dc-dc converter settings, etc.
16.6. Selecting the Optimum Switch Size
The dc-dc converter has two built-in switches (the diode bypass switch and duty cycle control switch). To
maximize efficiency, one of two switch sizes may be selected. The large switches are ideal for carrying
high currents and the small switches are ideal for low current applications. The ideal switchover point to
switch from the small switches to the large switches varies with the programmed output voltage. At an output voltage of 2 V, the ideal switchover point is at approximately 4 mA total output current. At an output
voltage of 3 V, the ideal switchover point is at approximately 8 mA total output current.
16.7. DC-DC Converter Clocking Options
The dc-dc converter may be clocked from its internal oscillator, or from any system clock source, selectable by the CLKSEL bit (DC0CF.0). The dc-dc converter internal oscillator frequency is approximately
2.4 MHz. For a more accurate clock source, the system clock, or a divided version of the system clock may
be used as the dc-dc clock source. The dc-dc converter has a built in clock divider (configured using
DC0CF[6:5]) which allows any system clock frequency over 1.6 MHz to generate a valid clock in the range
of 1.6 to 3.2 MHz.
When the precision internal oscillator is selected as the system clock source, the OSCICL register may be
used to fine tune the oscillator frequency and the dc-dc converter clock. The oscillator frequency should
only be decreased since it is factory calibrated at its maximum frequency. The minimum frequency which
can be reached by the oscillator after taking into account process variations is approximately 16 MHz. The
system clock routed to the dc-dc converter clock divider also may be inverted by setting the CLKINV bit
(DC0CF.3) to logic 1. These options can be used to minimize interference in noise sensitive applications.
172
Rev. 1.3
Si1000/1/2/3/4/5
16.8. DC-DC Converter Behavior in Sleep Mode
When the Si1000/1/2/3/4/5 devices are placed in Sleep mode, the dc-dc converter is disabled, and the
VDD_MCU/DC+ output is internally connected to VBAT by default. This behavior ensures that the GPIO
pins are powered from a low-impedance source during sleep mode. If the GPIO pins are not used as
inputs or outputs during sleep mode, then the VDD_MCU/DC+ output can be made to float during Sleep
mode by setting the VDDSLP bit in the DC0CF register to 1.
Setting this bit can provide power savings in two ways. First, if the sleep interval is relatively short and the
VDD_MCU/DC+ load current (include leakage currents) is negligible, then the capacitor on
VDD_MCU/DC+ will maintain the output voltage near the programmed value, which means that the
VDD_MCU/DC+ capacitor will not need to be recharged upon every wake up event. The second power
advantage is that internal or external low-power circuits that require more than 1.8 V can continue to function during Sleep mode without operating the dc-dc converter, powered by the energy stored in the 1 µF
output decoupling capacitor. For example, the Si1004/5 comparators require about 0.4 µA when operating
in their lowest power mode. If the dc-dc converter output were increased to 3.3 V just before putting the
device into Sleep mode, then the comparator could be powered for more than 3 seconds before the output
voltage dropped to 1.8 V. In this example, the overall energy consumption would be much lower than if the
dc-dc converter were kept running to power the comparator.
If the load current on VDD_MCU/DC+ is high enough to discharge the VDD_MCU/DC+ capacitance to a
voltage lower than VBAT during the sleep interval, an internal diode will prevent VDD_MCU/DC+ from
dropping more than a few hundred millivolts below VBAT. There may be some additional leakage current
from VBAT to ground when the VDD_MCU/DC+ level falls below VBAT, but this leakage current should be
small compared to the current from VDD_MCU/DC+.
The amount of time that it takes for a device configured in one-cell mode to wake up from Sleep mode
depends on a number of factors, including the dc-dc converter clock speed, the settings of the SWSEL and
ILIMIT bits, the battery internal resistance, the load current, and the difference between the VBAT voltage
level and the programmed output voltage. The wake up time can be as short as 2 µs, though it is more
commonly in the range of 5 to 10 µs, and it can exceed 50 µs under extreme conditions.
See Section “14. Power Management” on page 152 for more information about sleep mode.
Rev. 1.3
173
Si1000/1/2/3/4/5
16.9. DC-DC Converter Register Descriptions
The SFRs used to configure the dc-dc converter are described in the following register descriptions. The
reset values for these registers can be used as-is in most systems; therefore, no software intervention or
initialization is required.
SFR Definition 16.1. DC0CN: DC-DC Converter Control
Bit
7
6
5
4
3
2
1
Name
MINPW
SWSEL
Reserved
SYNC
VSEL
Type
R/W
R/W
R/W
R/W
R/W
1
0
0
Reset
0
0
SFR Page = 0x0; SFR Address = 0x97
Bit
Name
7:6
0
0
0
1
Function
MINPW[1:0] DC-DC Converter Minimum Pulse Width.
Specifies the minimum pulse width.
00: No minimum duty cycle.
01: Minimum pulse width is 20 ns.
10: Minimum pulse width is 40 ns.
11: Minimum pulse width is 80 ns.
5
SWSEL
DC-DC Converter Switch Select.
Selects one of two possible converter switch sizes to maximize efficiency.
0: The large switches are selected (best efficiency for high output currents).
1: The small switches are selected (best efficiency for low output currents).
4
Reserved
3
SYNC
Always Write to 0.
ADC0 Synchronization Enable.
When synchronization is enabled, the ADC0SC[4:0] bits in the ADC0CF register
must be set to 00000b. Behavior as described is valid in REVC and later devices.
0: The ADC is not synchronized to the dc-dc converter.
1: The ADC is synchronized to the dc-dc converter. ADC0 tracking is performed
during the longest quiet time of the dc-dc converter switching cycle and ADC0 SAR
clock is also synchronized to the dc-dc converter switching cycle.
2:0
VSEL[2:0]
DC-DC Converter Output Voltage Select.
Specifies the target output voltage.
000: Target output voltage is 1.8 V.
001: Target output voltage is 1.9 V.
010: Target output voltage is 2.0 V.
011: Target output voltage is 2.1 V.
100: Target output voltage is 2.4 V.
101: Target output voltage is 2.7 V.
110: Target output voltage is 3.0 V.
111: Target output voltage is 3.3 V.
174
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 16.2. DC0CF: DC-DC Converter Configuration
Bit
7
6
Name
Reserved
Type
R
R/W
Reset
0
0
5
4
3
2
1
0
AD0CKINV
CLKINV
ILIMIT
VDDSLP
CLKSEL
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
CLKDIV[1:0]
SFR Page = 0x0; SFR Address = 0x96
Bit
Name
7
6:5
Reserved
Function
Read = 0b; Must write 0b.
CLKDIV[1:0] DC-DC Clock Divider.
Divides the dc-dc converter clock when the system clock is selected as the clock
source for dc-dc converter. These bits are ignored when the dc-dc converter is
clocked from its local oscillator.
00: The dc-dc converter clock is system clock divided by 1.
01: The dc-dc converter clock is system clock divided by 2.
10: The dc-dc converter clock is system clock divided by 4.
11: The dc-dc converter clock is system clock divided by 8.
4
AD0CKINV ADC0 Clock Inversion (Clock Invert During Sync).
Inverts the ADC0 SAR clock derived from the dc-dc converter clock when the SYNC
bit (DC0CN.3) is enabled. This bit is ignored when the SYNC bit is set to zero.
0: ADC0 SAR clock is inverted.
1: ADC0 SAR clock is not inverted.
3
CLKINV
DC-DC Converter Clock Invert.
Inverts the system clock used as the input to the dc-dc clock divider.
0: The dc-dc converter clock is not inverted.
1: The dc-dc converter clock is inverted.
2
ILIMIT
Peak Current Limit Threshold.
Sets the threshold for the maximum allowed peak inductor current. See Table 16.1
for peak inductor current levels.
0: Peak inductor current is set at a lower level.
1: Peak inductor current is set at a higher level.
1
VDDSLP
VDD_MCU/DC+ Sleep Mode Connection.
Specifies the power source for VDD_MCU/DC+ in Sleep Mode when the dc-dc converter is enabled.
0: VDD_MCU/DC+ connected to VBAT in Sleep Mode.
1: VDD_MCU/DC+ is floating in Sleep Mode.
0
CLKSEL
DC-DC Converter Clock Source Select.
Specifies the dc-dc converter clock source.
0: The dc-dc converter is clocked from its local oscillator.
1: The dc-dc converter is clocked from the system clock.
Rev. 1.3
175
Si1000/1/2/3/4/5
16.10. DC-DC Converter Specifications
See Table 4.14 on page 64 for a detailed listing of dc-dc converter specifications.
176
Rev. 1.3
Si1000/1/2/3/4/5
17. Voltage Regulator (VREG0)
Si1000/1/2/3/4/5 devices include an internal voltage regulator (VREG0) to regulate the internal core supply
to 1.8 V from a VDD_MCU supply of 1.8 to 3.6 V. Electrical characteristics for the on-chip regulator are
specified in the Electrical Specifications chapter.
The REG0CN register allows the Precision Oscillator Bias to be disabled, saving approximately 80 µA in
all non-Sleep power modes. This bias should only be disabled when the precision oscillator is not being
used.
The internal regulator (VREG0) is disabled when the device enters Sleep Mode and remains enabled
when the device enters Suspend Mode. See Section “14. Power Management” on page 152 for complete
details about low power modes.
SFR Definition 17.1. REG0CN: Voltage Regulator Control
Bit
7
Name
6
5
4
Reserved
Reserved
OSCBIAS
3
2
1
0
Reserved
Type
R
R/W
R/W
R/W
R
R
R
R/W
Reset
0
0
0
1
0
0
0
0
SFR Page = 0x0; SFR Address = 0xC9
Bit
Name
7
Unused
Function
Read = 0b. Write = Don’t care.
6:5
Reserved Read = 0b. Must Write 0b.
4
OSCBIAS Precision Oscillator Bias.
When set to 1, the bias used by the precision oscillator is forced on. If the precision
oscillator is not being used, this bit may be cleared to 0 to save approximately 80 µA
of supply current in all non-Sleep power modes. If disabled then re-enabled, the precision oscillator bias requires 4 µs of settling time.
3:1
0
Unused
Read = 000b. Write = Don’t care.
Reserved Read = 0b. Must Write 0b.
17.1. Voltage Regulator Electrical Specifications
See Table 4.15 on page 65 for detailed Voltage Regulator Electrical Specifications.
Rev. 1.3
177
Si1000/1/2/3/4/5
18. Reset Sources
Reset circuitry allows the controller to be easily placed in a predefined default condition. On entry to this
reset state, the following occur:
CIP-51 halts program execution
 Special Function Registers (SFRs) are initialized to their defined reset values
 External Port pins are forced to a known state
 Interrupts and timers are disabled
All SFRs are reset to the predefined values noted in the SFR descriptions. The contents of RAM are unaffected during a reset; any previously stored data is preserved as long as power is not lost. Since the stack
pointer SFR is reset, the stack is effectively lost, even though the data on the stack is not altered.

The Port I/O latches are reset to 0xFF (all logic ones) in open-drain mode. Weak pullups are enabled
during and after the reset. For VDD Monitor and power-on resets, the RST pin is driven low until the device
exits the reset state.
On exit from the reset state, the program counter (PC) is reset, and the system clock defaults to an internal
oscillator. Refer to Section “19. Clocking Sources” on page 185 for information on selecting and configuring the system clock source. The Watchdog Timer is enabled with the system clock divided by 12 as its
clock source (Section “28.4. Watchdog Timer Mode” on page 368 details the use of the Watchdog Timer).
Program execution begins at location 0x0000.
VDD_MCU/DC+
+
-
Px.x
SmaRTClock
Power On
Reset
Supply
Monitor
Comparator 0
Px.x
VBAT
+
-
C0RSEF
*On Si1000/1/2/3 devices,
VBAT is internally
connected to VDD_MCU.
(wired-OR)
RST
0
Enable
RTC0RE
Missing
Clock
Detector
(oneshot)
EN
Reset
Funnel
PCA
WDT
(Software Reset)
SWRSF
System
Clock
Illegal Flash
Operation
WDT
Enable
MCD
Enable
EN
CIP-51
Microcontroller
Core
System Reset
System Reset
Power Management
Block (PMU0)
Reset
Extended Interrupt
Handler
Figure 18.1. Reset Sources
178
Rev. 1.3
Power-On Reset
Si1000/1/2/3/4/5
18.1. Power-On (VBAT Supply Monitor) Reset
During power-up, the device is held in a reset state and the RST pin is driven low until VBAT settles above
VPOR. An additional delay occurs before the device is released from reset; the delay decreases as the
VBAT ramp time increases (VBAT ramp time is defined as how fast VBAT ramps from 0 V to VPOR).
Figure 18.3 plots the power-on and VDD monitor reset timing. For valid ramp times (less than 3 ms), the
power-on reset delay (TPORDelay) is typically 3 ms (VBAT = 0.9 V), 7 ms (VBAT = 1.8 V), or 15 ms (VBAT =
3.6 V).
Note: The maximum VDD ramp time is 3 ms; slower ramp times may cause the device to be released from reset
before VBAT reaches the VPOR level.
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. When PORSF is
set, all of the other reset flags in the RSTSRC Register are indeterminate (PORSF is cleared by all other
resets). Since all resets cause program execution to begin at the same location (0x0000), software can
read the PORSF flag to determine if a power-up was the cause of reset. The contents of internal data
memory should be assumed to be undefined after a power-on reset.
volts
Note: Si1000/1/2/3 have the VBAT signal internally connected to VDD_MCU.
VBAT
~0.8
VPOR
VB
AT
0.6
~0.5
See specification
table for min/max
voltages.
t
Logic HIGH
Logic LOW
RST
TPORDelay
Power-On
Reset
TPORDelay
Power-On
Reset
Figure 18.2. Power-Fail Reset Timing Diagram
Rev. 1.3
179
Si1000/1/2/3/4/5
18.2. Power-Fail (VDD_MCU Supply Monitor) Reset
Si1000/1/2/3/4/5 devices have a VDD_MCU Supply Monitor that is enabled and selected as a reset source
after each power-on or power-fail reset. When enabled and selected as a reset source, any power down
transition or power irregularity that causes VDD_MCU to drop below VRST will cause the RST pin to be
driven low and the CIP-51 will be held in a reset state (see Figure 18.3). When VDD_MCU returns to a
level above VRST, the CIP-51 will be released from the reset state.
After a power-fail reset, the PORSF flag reads 1, the contents of RAM invalid, and the VDD_MCU supply
monitor is enabled and selected as a reset source. The enable state of the VDD_MCU supply monitor and
its selection as a reset source is only altered by power-on and power-fail resets. For example, if the
VDD_MCU supply monitor is de-selected as a reset source and disabled by software, then a software
reset is performed, the VDD_MCU supply monitor will remain disabled and de-selected after the reset.
In battery-operated systems, the contents of RAM can be preserved near the end of the battery’s usable
life if the device is placed in sleep mode prior to a power-fail reset occurring. When the device is in sleep
mode, the power-fail reset is automatically disabled and the contents of RAM are preserved as long as the
VBAT supply does not fall below VPOR. A large capacitor can be used to hold the power supply voltage
above VPOR while the user is replacing the battery. Upon waking from sleep mode, the enable and reset
source select state of the VDD_MCU supply monitor are restored to the value last set by the user.
To allow software early notification that a power failure is about to occur, the VDDOK bit is cleared when
the VDD_MCU supply falls below the VWARN threshold. The VDDOK bit can be configured to generate an
interrupt. See Section “12. Interrupt Handler” on page 130 for more details.
volts
Important Note: To protect the integrity of Flash contents, the VDD_MCU supply monitor must be
enabled and selected as a reset source if software contains routines which erase or write Flash
memory. If the VDD_MCU supply monitor is not enabled, any erase or write performed on Flash memory
will cause a Flash Error device reset.
VDD_MCU/DC+
V WARN
V RST
VBAT
V POR
t
VDDOK
SLEEP
RST
Active M ode
Pow er-Fail R eset
Sleep M ode
R AM Retained - No Reset
N ote: W akeup signal
required after new
battery insertion
Figure 18.3. Power-Fail Reset Timing Diagram
180
Rev. 1.3
Si1000/1/2/3/4/5
Important Notes:
The Power-on Reset (POR) delay is not incurred after a VDD_MCU supply monitor reset. See Section
“4. Electrical Characteristics” on page 40 for complete electrical characteristics of the VDD_MCU
monitor.
 Software should take care not to inadvertently disable the VDD Monitor as a reset source when writing
to RSTSRC to enable other reset sources or to trigger a software reset. All writes to RSTSRC should
explicitly set PORSF to '1' to keep the VDD Monitor enabled as a reset source.


The VDD_MCU supply monitor must be enabled before selecting it as a reset source. Selecting the
VDD_MCU supply monitor as a reset source before it has stabilized may generate a system reset. In
systems where this reset would be undesirable, a delay should be introduced between enabling the
VDD_MCU supply monitor and selecting it as a reset source. See Section “4. Electrical Characteristics”
on page 40 for minimum VDD_MCU Supply Monitor turn-on time. No delay should be introduced in
systems where software contains routines that erase or write Flash memory. The procedure for
enabling the VDD_MCU supply monitor and selecting it as a reset source is shown below:
1. Enable the VDD_MCU Supply Monitor (VDMEN bit in VDM0CN = 1).
2. Wait for the VDD_MCU Supply Monitor to stabilize (optional).
3. Select the VDD_MCU Supply Monitor as a reset source (PORSF bit in RSTSRC = 1).
Rev. 1.3
181
Si1000/1/2/3/4/5
SFR Definition 18.1. VDM0CN: VDD_MCU Supply Monitor Control
Bit
7
6
5
4
3
2
Name
VDMEN
VDDSTAT
VDDOK
Reserved
Reserved
Reserved
Type
R/W
R
R
R/W
R/W
Reset
1
Varies
Varies
0
0
SFR Page = 0x0; SFR Address = 0xFF
Bit
Name
7
VDMEN
1
0
R/W
R/W
R/W
0
0
0
Function
VDD_MCU Supply Monitor Enable.
This bit turns the VDD_MCU supply monitor circuit on/off. The VDD_MCU Supply
Monitor cannot generate system resets until it is also selected as a reset source in
register RSTSRC (SFR Definition 18.2).
0: VDD_MCU Supply Monitor Disabled.
1: VDD_MCU Supply Monitor Enabled.
6
VDDSTAT
VDD_MCU Supply Status.
This bit indicates the current power supply status.
0: VDD_MCU is at or below the VRST threshold.
1: VDD_MCU is above the VRST threshold.
5
VDDOK
VDD_MCU Supply Status (Early Warning).
This bit indicates the current power supply status.
0: VDD_MCU is at or below the VWARN threshold.
1: VDD_MCU is above the VWARN monitor threshold.
4:2
Reserved
Read = 000b. Must Write 000b.
1:0
Unused
Read = 00b. Write = Don’t Care.
18.3. External Reset
The external RST pin provides a means for external circuitry to force the device into a reset state. Asserting an active-low signal on the RST pin generates a reset; an external pullup and/or decoupling of the RST
pin may be necessary to avoid erroneous noise-induced resets. See Table 4.4 for complete RST pin specifications. The external reset remains functional even when the device is in the low power Suspend and
Sleep Modes. The PINRSF flag (RSTSRC.0) is set on exit from an external reset.
18.4. Missing Clock Detector Reset
The Missing Clock Detector (MCD) is a one-shot circuit that is triggered by the system clock. If the system
clock remains high or low for more than 100 µs, the one-shot will time out and generate a reset. After a
MCD reset, the MCDRSF flag (RSTSRC.2) will read 1, signifying the MCD as the reset source; otherwise,
this bit reads 0. Writing a 1 to the MCDRSF bit enables the Missing Clock Detector; writing a 0 disables it.
The missing clock detector reset is automatically disabled when the device is in the low power Suspend or
Sleep mode. Upon exit from either low power state, the enabled/disabled state of this reset source is
restored to its previous value. The state of the RST pin is unaffected by this reset.
182
Rev. 1.3
Si1000/1/2/3/4/5
18.5. Comparator0 Reset
Comparator0 can be configured as a reset source by writing a 1 to the C0RSEF flag (RSTSRC.5). Comparator0 should be enabled and allowed to settle prior to writing to C0RSEF to prevent any turn-on chatter
on the output from generating an unwanted reset. The Comparator0 reset is active-low: if the non-inverting
input voltage (on CP0+) is less than the inverting input voltage (on CP0-), the device is put into the reset
state. After a Comparator0 reset, the C0RSEF flag (RSTSRC.5) will read 1 signifying Comparator0 as the
reset source; otherwise, this bit reads 0. The Comparator0 reset source remains functional even when the
device is in the low power Suspend and Sleep states as long as Comparator0 is also enabled as a wakeup source. The state of the RST pin is unaffected by this reset.
18.6. PCA Watchdog Timer Reset
The programmable Watchdog Timer (WDT) function of the Programmable Counter Array (PCA) can be
used to prevent software from running out of control during a system malfunction. The PCA WDT function
can be enabled or disabled by software as described in Section “28.4. Watchdog Timer Mode” on
page 368; the WDT is enabled and clocked by SYSCLK / 12 following any reset. If a system malfunction
prevents user software from updating the WDT, a reset is generated and the WDTRSF bit (RSTSRC.5) is
set to 1. The PCA Watchdog Timer reset source is automatically disabled when the device is in the low
power Suspend or Sleep mode. Upon exit from either low power state, the enabled/disabled state of this
reset source is restored to its previous value.The state of the RST pin is unaffected by this reset.
18.7. Flash Error Reset
If a Flash read/write/erase or program read targets an illegal address, a system reset is generated. This
may occur due to any of the following:





A Flash write or erase is attempted above user code space. This occurs when PSWE is set to 1 and a
MOVX write operation targets an address above the Lock Byte address.
A Flash read is attempted above user code space. This occurs when a MOVC operation targets an
address above the Lock Byte address.
A Program read is attempted above user code space. This occurs when user code attempts to branch
to an address above the Lock Byte address.
A Flash read, write or erase attempt is restricted due to a Flash security setting (see Section
“13.3. Security Options” on page 144).
A Flash write or erase is attempted while the VDD Monitor is disabled.
The FERROR bit (RSTSRC.6) is set following a Flash error reset. The state of the RST pin is unaffected by
this reset.
18.8. SmaRTClock (Real Time Clock) Reset
The SmaRTClock can generate a system reset on two events: SmaRTClock Oscillator Fail or SmaRTClock Alarm. The SmaRTClock Oscillator Fail event occurs when the SmaRTClock Missing Clock Detector
is enabled and the SmaRTClock clock is below approximately 20 kHz. A SmaRTClock alarm event occurs
when the SmaRTClock Alarm is enabled and the SmaRTClock timer value matches the ALARMn registers. The SmaRTClock can be configured as a reset source by writing a 1 to the RTC0RE flag
(RSTSRC.7). The SmaRTClock reset remains functional even when the device is in the low power Suspend or Sleep mode. The state of the RST pin is unaffected by this reset.
18.9. Software Reset
Software may force a reset by writing a 1 to the SWRSF bit (RSTSRC.4). The SWRSF bit will read 1 following a software forced reset. The state of the RST pin is unaffected by this reset.
Rev. 1.3
183
Si1000/1/2/3/4/5
SFR Definition 18.2. RSTSRC: Reset Source
Bit
7
6
5
4
3
2
1
0
Name
RTC0RE
FERROR
C0RSEF
SWRSF
WDTRSF
MCDRSF
PORSF
PINRSF
Type
R/W
R
R/W
R/W
R
R/W
R/W
R
Reset
Varies
Varies
Varies
Varies
Varies
Varies
Varies
Varies
SFR Page = 0x0; SFR Address = 0xEF.
Bit
Name
Description
Write
Read
7
RTC0RE SmaRTClock Reset Enable
and Flag
Set to 1 if SmaRTClock
0: Disable SmaRTClock
alarm or oscillator fail
as a reset source.
1: Enable SmaRTClock as caused the last reset.
a reset source.
6
FERROR Flash Error Reset Flag.
N/A
5
C0RSEF Comparator0 Reset Enable
and Flag.
0: Disable Comparator0 as Set to 1 if Comparator0
a reset source.
caused the last reset.
1: Enable Comparator0 as
a reset source.
4
SWRSF
Writing a 1 forces a system reset.
Software Reset Force and
Flag.
3
WDTRSF Watchdog Timer Reset Flag. N/A
2
MCDRSF Missing Clock Detector
(MCD) Enable and Flag.
Set to 1 if Flash
read/write/erase error
caused the last reset.
Set to 1 if last reset was
caused by a write to
SWRSF.
Set to 1 if Watchdog Timer
overflow caused the last
reset.
Set to 1 if Missing Clock
0: Disable the MCD.
Detector timeout caused
1: Enable the MCD.
The MCD triggers a reset the last reset.
if a missing clock condition
is detected.
1
PORSF
Power-On / Power-Fail
Reset Flag, and Power-Fail
Reset Enable.
0: Disable the VDD_MCU
Supply Monitor as a reset
source.
1: Enable the VDD_MCU
Supply Monitor as a reset
source.3
Set to 1 anytime a poweron or VDD monitor reset
occurs.2
0
PINRSF
HW Pin Reset Flag.
N/A
Set to 1 if RST pin caused
the last reset.
Notes:
1. It is safe to use read-modify-write operations (ORL, ANL, etc.) to enable or disable specific interrupt sources.
2. If PORSF read back 1, the value read from all other bits in this register are indeterminate.
3. Writing a 1 to PORSF before the VDD_MCU Supply Monitor is stabilized may generate a system reset.
184
Rev. 1.3
Si1000/1/2/3/4/5
19. Clocking Sources
Si1000/1/2/3/4/5 devices include a programmable precision internal oscillator, an external oscillator drive
circuit, a low power internal oscillator, and a SmaRTClock real time clock oscillator. The precision internal
oscillator can be enabled/disabled and calibrated using the OSCICN and OSCICL registers, as shown in
Figure 19.1. The external oscillator can be configured using the OSCXCN register. The low power internal
oscillator is automatically enabled and disabled when selected and deselected as a clock source. SmaRTClock operation is described in the SmaRTClock oscillator chapter.
The system clock (SYSCLK) can be derived from the precision internal oscillator, external oscillator, low
power internal oscillator, or SmaRTClock oscillator. The global clock divider can generate a system clock
that is 1, 2, 4, 8, 16, 32, 64, or 128 times slower that the selected input clock source. Oscillator electrical
specifications can be found in the Electrical Specifications Chapter.
OSCICL
OSCICN
CLKSEL
VDD
XTAL2
CLKSL1
CLKSL0
CLKRDY
CLKDIV2
CLKDIV1
CLKDIV0
Option 3
IOSCEN
IFRDY
Option 2
XTAL2
EN
Precision
Internal Oscillator
Option 1
Precision Internal Oscillator
XTAL1
External Oscillator
External
Oscillator
Drive Circuit
10M
CLKRDY
Low Power Internal Oscillator
XTAL2
n
SYSCLK
Clock Divider
smaRTClock Oscillator
Option 4
XFCN2
XFCN1
XFCN0
XTLVLD
XOSCMD2
XOSCMD1
XOSCMD0
XTAL2
Low Power
Internal Oscillator
smaRTClock
Oscillator
OSCXCN
Figure 19.1. Clocking Sources Block Diagram
The proper way of changing the system clock when both the clock source and the clock divide value are
being changed is as follows:
If switching from a fast “undivided” clock to a slower “undivided” clock:
1. Change the clock divide value.
2. Poll for CLKRDY > 1.
3. Change the clock source.
If switching from a slow “undivided” clock to a faster “undivided” clock:
1. Change the clock source.
2. Change the clock divide value.
3. Poll for CLKRDY > 1.
Rev. 1.3
185
Si1000/1/2/3/4/5
19.1. Programmable Precision Internal Oscillator
All Si1000/1/2/3/4/5 devices include a programmable precision internal oscillator that may be selected as
the system clock. OSCICL is factory calibrated to obtain a 24.5 MHz frequency. See Table 4.7, “Internal
Precision Oscillator Electrical Characteristics,” on page 58 for complete oscillator specifications.
The precision oscillator supports a spread spectrum mode which modulates the output frequency in order
to reduce the EMI generated by the system. When enabled (SSE = 1), the oscillator output frequency is
modulated by a stepped triangle wave whose frequency is equal to the oscillator frequency divided by 384
(63.8 kHz using the factory calibration). The deviation from the nominal oscillator frequency is +0%, –1.6%,
and the step size is typically 0.26% of the nominal frequency. When using this mode, the typical average
oscillator frequency is lowered from 24.5 MHz to 24.3 MHz.
19.2. Low Power Internal Oscillator
All Si1000/1/2/3/4/5 devices include a low power internal oscillator that defaults as the system clock after a
system reset. The low power internal oscillator frequency is 20 MHz ± 10% and is automatically enabled
when selected as the system clock and disabled when not in use. See Table 4.8, “Internal Low-Power
Oscillator Electrical Characteristics,” on page 58 for complete oscillator specifications.
19.3. External Oscillator Drive Circuit
All Si1000/1/2/3/4/5 devices include an external oscillator circuit that may drive an external crystal, ceramic
resonator, capacitor, or RC network. A CMOS clock may also provide a clock input. Figure 19.1 shows a
block diagram of the four external oscillator options. The external oscillator is enabled and configured
using the OSCXCN register.
The external oscillator output may be selected as the system clock or used to clock some of the digital
peripherals (e.g., Timers, PCA, etc.). See the data sheet chapters for each digital peripheral for details.
See Section “4. Electrical Characteristics” on page 40 for complete oscillator specifications.
19.3.1. External Crystal Mode
If a crystal or ceramic resonator is used as the external oscillator, the crystal/resonator and a 10 Mresistor must be wired across the XTAL1 and XTAL2 pins as shown in Figure 19.1, Option 1. Appropriate loading capacitors should be added to XTAL1 and XTAL2, and both pins should be configured for analog I/O
with the digital output drivers disabled.
Figure 19.2 shows the external oscillator circuit for a 20 MHz quartz crystal with a manufacturer recommended load capacitance of 12.5 pF. Loading capacitors are "in series" as seen by the crystal and "in parallel" with the stray capacitance of the XTAL1 and XTAL2 pins. The total value of the each loading
capacitor and the stray capacitance of each XTAL pin should equal 12.5pF x 2 = 25 pF. With a stray capacitance of 10 pF per pin, the 15 pF capacitors yield an equivalent series capacitance of 12.5 pF across the
crystal.
Note: The recommended load capacitance depends upon the crystal and the manufacturer. Please refer to the crystal
data sheet when completing these calculations.
186
Rev. 1.3
Si1000/1/2/3/4/5
15 pF
XTAL1

10 M
25 MHz
XTAL2
15 pF
Figure 19.2. 25 MHz External Crystal Example
Important Note on External Crystals: Crystal oscillator circuits are quite sensitive to PCB layout. The
crystal should be placed as close as possible to the XTAL pins on the device. The traces should be as
short as possible and shielded with ground plane from any other traces which could introduce noise or
interference.
When using an external crystal, the external oscillator drive circuit must be configured by software for Crystal Oscillator Mode or Crystal Oscillator Mode with divide by 2 stage. The divide by 2 stage ensures that the
clock derived from the external oscillator has a duty cycle of 50%. The External Oscillator Frequency Control value (XFCN) must also be specified based on the crystal frequency. The selection should be based on
Table 19.1. For example, a 25 MHz crystal requires an XFCN setting of 111b.
Table 19.1. Recommended XFCN Settings for Crystal Mode
XFCN
Crystal Frequency
Bias Current
Typical Supply Current
(VDD = 2.4 V)
000
f  20 kHz
0.5 µA
3.0 µA, f = 32.768 kHz
001
20 kHz f 58 kHz
1.5 µA
4.8 µA, f = 32.768 kHz
010
58 kHz  f 155 kHz
4.8 µA
9.6 µA, f = 32.768 kHz
011
155 kHz  f 415 kHz
14 µA
28 µA, f = 400 kHz
100
415 kHz  f 1.1 MHz
40 µA
71 µA, f = 400 kHz
101
1.1 MHz  f 3.1 MHz
120 µA
193 µA, f = 400 kHz
110
3.1 MHz  f 8.2 MHz
550 µA
940 µA, f = 8 MHz
111
8.2 MHz  f 25 MHz
2.6 mA
3.9 mA, f = 25 MHz
When the crystal oscillator is first enabled, the external oscillator valid detector allows software to determine when the external system clock has stabilized. Switching to the external oscillator before the crystal
oscillator has stabilized can result in unpredictable behavior. The recommended procedure for starting the
crystal is:
1. Configure XTAL1 and XTAL2 for analog I/O and disable the digital output drivers.
2. Configure and enable the external oscillator.
3. Poll for XTLVLD => 1.
4. Switch the system clock to the external oscillator.
Rev. 1.3
187
Si1000/1/2/3/4/5
19.3.2. External RC Mode
If an RC network is used as the external oscillator, the circuit should be configured as shown in
Figure 19.1, Option 2. The RC network should be added to XTAL2, and XTAL2 should be configured for
analog I/O with the digital output drivers disabled. XTAL1 is not affected in RC mode.
The capacitor should be no greater than 100 pF; however for very small capacitors, the total capacitance
may be dominated by parasitic capacitance in the PCB layout. The resistor should be no smaller than
10k. The oscillation frequency can be determined by the following equation:
3
1.23  10
f = ------------------------RC
where
f = frequency of clock in MHzR = pull-up resistor value in k
VDD = power supply voltage in VoltsC = capacitor value on the XTAL2 pin in pF
To determine the required External Oscillator Frequency Control value (XFCN) in the OSCXCN Register,
first select the RC network value to produce the desired frequency of oscillation. For example, if the frequency desired is 100 kHz, let R = 246 k and C = 50 pF:
3
3
1.23  10
1.23  10
f = ------------------------- = ------------------------- = 100 kHz
RC
246  50
where
f = frequency of clock in MHz; R = pull-up resistor value in k
VDD = power supply voltage in Volts; C = capacitor value on the XTAL2 pin in pF
Referencing Table 19.2, the recommended XFCN setting is 010.
Table 19.2. Recommended XFCN Settings for RC and C modes
XFCN
Approximate
Frequency Range (RC
and C Mode)
K Factor (C Mode)
Typical Supply Current/ Actual
Measured Frequency
(C Mode, VDD = 2.4 V)
000
f 25 kHz
K Factor = 0.87
3.0 µA, f = 11 kHz, C = 33 pF
001
25 kHz f 50 kHz
K Factor = 2.6
5.5 µA, f = 33 kHz, C = 33 pF
010
50 kHz f 100 kHz
K Factor = 7.7
13 µA, f = 98 kHz, C = 33 pF
011
100 kHz f 200 kHz
K Factor = 22
32 µA, f = 270 kHz, C = 33 pF
100
200 kHz f 400 kHz
K Factor = 65
82 µA, f = 310 kHz, C = 46 pF
101
400 kHz f 800 kHz
K Factor = 180
242 µA, f = 890 kHz, C = 46 pF
110
800 kHz f 1.6 MHz
K Factor = 664
1.0 mA, f = 2.0 MHz, C = 46 pF
111
1.6 MHz f 3.2 MHz
K Factor = 1590
4.6 mA, f = 6.8 MHz, C = 46 pF
When the RC oscillator is first enabled, the external oscillator valid detector allows software to determine
when oscillation has stabilized. The recommended procedure for starting the RC oscillator is:
1. Configure XTAL2 for analog I/O and disable the digital output drivers.
2. Configure and enable the external oscillator.
188
Rev. 1.3
Si1000/1/2/3/4/5
3. Poll for XTLVLD > 1.
4. Switch the system clock to the external oscillator.
19.3.3. External Capacitor Mode
If a capacitor is used as the external oscillator, the circuit should be configured as shown in Figure 19.1,
Option 3. The capacitor should be added to XTAL2, and XTAL2 should be configured for analog I/O with
the digital output drivers disabled. XTAL1 is not affected in RC mode.
The capacitor should be no greater than 100 pF; however, for very small capacitors, the total capacitance
may be dominated by parasitic capacitance in the PCB layout. The oscillation frequency and the required
External Oscillator Frequency Control value (XFCN) in the OSCXCN Register can be determined by the
following equation:
KF
f = --------------------C  V DD
where
f = frequency of clock in MHzR = pull-up resistor value in k
VDD = power supply voltage in VoltsC = capacitor value on the XTAL2 pin in pF
Below is an example of selecting the capacitor and finding the frequency of oscillation Assume VDD = 3.0 V
and f = 150 kHz:
KF
f = --------------------C  V DD
KF
0.150 MHz = ----------------C  3.0
Since a frequency of roughly 150 kHz is desired, select the K Factor from Table 19.2 as KF = 22:
22
0.150 MHz = ----------------------C  3.0 V
22
C = ----------------------------------------------0.150 MHz  3.0 V
C = 48.8 pF
Therefore, the XFCN value to use in this example is 011 and C is approximately 50 pF.
The recommended startup procedure for C mode is the same as RC mode.
19.3.4. External CMOS Clock Mode
If an external CMOS clock is used as the external oscillator, the clock should be directly routed into XTAL2.
The XTAL2 pin should be configured as a digital input. XTAL1 is not used in external CMOS clock mode.
The external oscillator valid detector will always return zero when the external oscillator is configured to
External CMOS Clock mode.
Rev. 1.3
189
Si1000/1/2/3/4/5
19.4. Special Function Registers for Selecting and Configuring the System Clock
The clocking sources on Si1000/1/2/3/4/5 devices are enabled and configured using the OSCICN,
OSCICL, OSCXCN and the SmaRTClock internal registers. See Section “20. SmaRTClock (Real Time
Clock)” on page 193 for SmaRTClock register descriptions. The system clock source for the MCU can be
selected using the CLKSEL register. To minimize active mode current, the oneshot timer which sets Flash
read time should by bypassed when the system clock is greater than 10 MHz. See the FLSCL register
description for details.
The clock selected as the system clock can be divided by 1, 2, 4, 8, 16, 32, 64, or 128. When switching
between two clock divide values, the transition may take up to 128 cycles of the undivided clock source.
The CLKRDY flag can be polled to determine when the new clock divide value has been applied. The clock
divider must be set to "divide by 1" when entering Suspend or Sleep Mode.
The system clock source may also be switched on-the-fly. The switchover takes effect after one clock
period of the slower oscillator.
SFR Definition 19.1. CLKSEL: Clock Select
Bit
7
6
5
4
3
2
Name
CLKRDY
Type
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
1
1
0
1
0
0
CLKDIV[2:0]
1
0
CLKSEL[2:0]
SFR Page = All Pages; SFR Address = 0xA9
Bit
Name
7
CLKRDY
6:4
3
2:0
190
CLKDIV[2:0]
Unused
CLKSEL[2:0]
Function
System Clock Divider Clock Ready Flag.
0: The selected clock divide setting has not been applied to the system clock.
1: The selected clock divide setting has been applied to the system clock.
System Clock Divider Bits.
Selects the clock division to be applied to the undivided system clock source.
000: System clock is divided by 1.
001: System clock is divided by 2.
010: System clock is divided by 4.
011: System clock is divided by 8.
100: System clock is divided by 16.
101: System clock is divided by 32.
110: System clock is divided by 64.
111: System clock is divided by 128.
Read = 0b. Must Write 0b.
System Clock Select.
Selects the oscillator to be used as the undivided system clock source.
000: Precision Internal Oscillator.
001: External Oscillator.
010: Reserved.
011: SmaRTClock Oscillator.
1xx: Low Power Oscillator.
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 19.2. OSCICN: Internal Oscillator Control
Bit
7
6
5
4
3
Name
IOSCEN
IFRDY
Type
R/W
R
R/W
R/W
R/W
Reset
0
0
0
0
1
2
1
0
R/W
R/W
R/W
1
1
1
Reserved[5:0]
SFR Page = 0x0; SFR Address = 0xB2
Bit
Name
7
IOSCEN
Function
Internal Oscillator Enable.
0: Internal oscillator disabled.
1: Internal oscillator enabled.
6
5:0
IFRDY
Internal Oscillator Frequency Ready Flag.
0: Internal oscillator is not running at its programmed frequency.
1: Internal oscillator is running at its programmed frequency.
Reserved Read = 001111b. Must Write 001111b.
Note: It is recommended to use read-modify-write operations such as ORL and ANL to set or clear the enable bit of
this register.
SFR Definition 19.3. OSCICL: Internal Oscillator Calibration
Bit
7
6
5
4
Name
SSE
Type
R/W
R
R/W
R/W
Reset
0
Varies
Varies
Varies
3
2
1
0
R/W
R/W
R/W
R/W
Varies
Varies
Varies
Varies
OSCICL[6:0]
SFR Page = 0x0; SFR Address = 0xB3
Bit
Name
7
SSE
6:0
OSCICL
Function
Spread Spectrum Enable.
0: Spread Spectrum clock dithering disabled.
1: Spread Spectrum clock dithering enabled.
Internal Oscillator Calibration.
Factory calibrated to obtain a frequency of 24.5 MHz. Incrementing this register decreases the
oscillator frequency and decrementing this register increases the oscillator frequency. The
step size is approximately 1% of the calibrated frequency. The recommended calibration frequency range is between 16 and 24.5 MHz.
Note: If the Precision Internal Oscillator is selected as the system clock, the following procedure should be used when
changing the value of the internal oscillator calibration bits.
1. Switch to a different clock source.
2. Disable the oscillator by writing OSCICN.7 to 0.
3. Change OSCICL to the desired setting.
4. Enable the oscillator by writing OSCICN.7 to 1.
Rev. 1.3
191
Si1000/1/2/3/4/5
SFR Definition 19.4. OSCXCN: External Oscillator Control
Bit
7
6
Name XCLKVLD
5
4
XOSCMD[2:0]
3
2
Reserved
1
0
XFCN[2:0]
Type
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xB1
Bit
7
Name
Function
XCLKVLD External Oscillator Valid Flag.
Provides External Oscillator status and is valid at all times for all modes of operation
except External CMOS Clock Mode and External CMOS Clock Mode with divide by
2. In these modes, XCLKVLD always returns 0.
0: External Oscillator is unused or not yet stable.
1: External Oscillator is running and stable.
6:4
XOSCMD External Oscillator Mode Bits.
Configures the external oscillator circuit to the selected mode.
00x: External Oscillator circuit disabled.
010: External CMOS Clock Mode.
011: External CMOS Clock Mode with divide by 2 stage.
100: RC Oscillator Mode.
101: Capacitor Oscillator Mode.
110: Crystal Oscillator Mode.
111: Crystal Oscillator Mode with divide by 2 stage.
3
2:0
Reserved Read = 0b. Must Write 0b.
XFCN
External Oscillator Frequency Control Bits.
Controls the external oscillator bias current.
000-111: See Table 19.1 on page 187 (Crystal Mode) or Table 19.2 on page 188 (RC
or C Mode) for recommended settings.
192
Rev. 1.3
Si1000/1/2/3/4/5
20. SmaRTClock (Real Time Clock)
Si1000/1/2/3/4/5 devices include an ultra low power 32-bit SmaRTClock Peripheral (Real Time Clock) with
alarm. The SmaRTClock has a dedicated 32 kHz oscillator that can be configured for use with or without a
crystal. No external resistor or loading capacitors are required. The on-chip loading capacitors are programmable to 16 discrete levels allowing compatibility with a wide range of crystals. The SmaRTClock can
operate directly from a 0.9–3.6 V battery voltage and remains operational even when the device goes into
its lowest power down mode.
The SmaRTClock allows a maximum of 36 hour 32-bit independent time-keeping when used with a
32.768 kHz Watch Crystal. The SmaRTClock provides an Alarm and Missing SmaRTClock events, which
could be used as reset or wakeup sources. See Section “18. Reset Sources” on page 178 and Section
“14. Power Management” on page 152 for details on reset sources and low power mode wake-up sources,
respectively.
XTAL3
XTAL4
SmaRTClock
Power/
Clock
Mgmt
Programmable Load Capacitors
SmaRTClock Oscillator
CIP-51 CPU
32-Bit
SmaRTClock
Timer
SmaRTClock State Machine
Wake-Up
Interrupt
Internal
Registers
CAPTUREn
RTC0CN
RTC0XCN
RTC0XCF
RTC0PIN
ALARMn
Interface
Registers
RTC0KEY
RTC0ADR
RTC0DAT
Figure 20.1. SmaRTClock Block Diagram
20.1. SmaRTClock Interface
The SmaRTClock Interface consists of three registers: RTC0KEY, RTC0ADR, and RTC0DAT. These interface registers are located on the CIP-51’s SFR map and provide access to the SmaRTClock internal registers listed in Table 20.1. The SmaRTClock internal registers can only be accessed indirectly through the
SmaRTClock Interface.
Rev. 1.3
193
Si1000/1/2/3/4/5
Table 20.1. SmaRTClock Internal Registers
SmaRTClock SmaRTClock
Address
Register
Register Name
Description
0x00–0x03
CAPTUREn
SmaRTClock Capture
Registers
Four Registers used for setting the 32-bit
SmaRTClock timer or reading its current value.
0x04
RTC0CN
SmaRTClock Control
Register
Controls the operation of the SmaRTClock State
Machine.
0x05
RTC0XCN
SmaRTClock Oscillator
Control Register
Controls the operation of the SmaRTClock
Oscillator.
0x06
RTC0XCF
SmaRTClock Oscillator
Configuration Register
Controls the value of the progammable
oscillator load capacitance and
enables/disables AutoStep.
0x07
RTC0PIN
SmaRTClock Pin
Configuration Register
Note: Forces XTAL3 and XTAL4 to be internally
shorted. 
This register also contains other reserved bits
which should not be modified.
0x08–0x0B
ALARMn
SmaRTClock Alarm
Registers
Four registers used for setting or reading the
32-bit SmaRTClock alarm value.
194
Rev. 1.3
Si1000/1/2/3/4/5
20.1.1. SmaRTClock Lock and Key Functions
The SmaRTClock Interface is protected with a lock and key function. The SmaRTClock Lock and Key Register (RTC0KEY) must be written with the correct key codes, in sequence, before writes and reads to
RTC0ADR and RTC0DAT may be performed. The key codes are: 0xA5, 0xF1. There are no timing restrictions, but the key codes must be written in order. If the key codes are written out of order, the wrong codes
are written, or an indirect register read or write is attempted while the interface is locked, the SmaRTClock
interface will be disabled, and the RTC0ADR and RTC0DAT registers will become inaccessible until the
next system reset. Once the SmaRTClock interface is unlocked, software may perform any number of
accesses to the SmaRTClock registers until the interface is re-locked or the device is reset. Any write to
RTC0KEY while the SmaRTClock interface is unlocked will re-lock the interface.
Reading the RTC0KEY register at any time will provide the SmaRTClock Interface status and will not interfere with the sequence that is being written. The RTC0KEY register description in SFR Definition 20.1 lists
the definition of each status code.
20.1.2. Using RTC0ADR and RTC0DAT to Access SmaRTClock Internal Registers
The SmaRTClock internal registers can be read and written using RTC0ADR and RTC0DAT. The
RTC0ADR register selects the SmaRTClock internal register that will be targeted by subsequent reads or
writes. Recommended instruction timing is provided in this section. If the recommended instruction timing
is not followed, then BUSY (RTC0ADR.7) should be checked prior to each read or write operation to make
sure the SmaRTClock Interface is not busy performing the previous read or write operation. A SmaRTClock Write operation is initiated by writing to the RTC0DAT register. Below is an example of writing to a
SmaRTClock internal register.
1. Poll BUSY (RTC0ADR.7) until it returns 0 or follow recommended instruction timing.
2. Write 0x05 to RTC0ADR. This selects the internal RTC0CN register at SmaRTClock Address 0x05.
3. Write 0x00 to RTC0DAT. This operation writes 0x00 to the internal RTC0CN register.
A SmaRTClock Read operation is initiated by setting the SmaRTClock Interface Busy bit. This transfers
the contents of the internal register selected by RTC0ADR to RTC0DAT. The transferred data will remain in
RTC0DAT until the next read or write operation. Below is an example of reading a SmaRTClock internal
register.
1. Poll BUSY (RTC0ADR.7) until it returns 0 or follow recommended instruction timing.
2. Write 0x05 to RTC0ADR. This selects the internal RTC0CN register at SmaRTClock Address 0x05.
3. Write 1 to BUSY. This initiates the transfer of data from RTC0CN to RTC0DAT.
4. Poll BUSY (RTC0ADR.7) until it returns 0 or follow recommend instruction timing.
5. Read data from RTC0DAT. This data is a copy of the RTC0CN register. 
Note: The RTC0ADR and RTC0DAT registers will retain their state upon a device reset.
20.1.3. RTC0ADR Short Strobe Feature
Reads and writes to indirect SmaRTClock registers normally take 7 system clock cycles. To minimize the
indirect register access time, the Short Strobe feature decreases the read and write access time to 6 system clocks. The Short Strobe feature is automatically enabled on reset and can be manually enabled/disabled using the SHORT (RTC0ADR.4) control bit.
Recommended Instruction Timing for a single register read with short strobe enabled:
mov RTC0ADR, #095h
nop
nop
nop
mov A, RTC0DAT
Rev. 1.3
195
Si1000/1/2/3/4/5
Recommended Instruction Timing for a single register write with short strobe enabled:
mov RTC0ADR, #095h
mov RTC0DAT, #000h
nop
20.1.4. SmaRTClock Interface Autoread Feature
When Autoread is enabled, each read from RTC0DAT initiates the next indirect read operation on the
SmaRTClock internal register selected by RTC0ADR. Software should set the BUSY bit once at the beginning of each series of consecutive reads. Software should follow recommended instruction timing or check
if the SmaRTClock Interface is busy prior to reading RTC0DAT. Autoread is enabled by setting AUTORD
(RTC0ADR.6) to logic 1.
20.1.5. RTC0ADR Autoincrement Feature
For ease of reading and writing the 32-bit CAPTURE and ALARM values, RTC0ADR automatically increments after each read or write to a CAPTUREn or ALARMn register. This speeds up the process of setting
an alarm or reading the current SmaRTClock timer value. Autoincrement is always enabled.
Recommended Instruction Timing for a multi-byte register read with short strobe and autoread enabled:
mov
nop
nop
nop
mov
nop
nop
mov
nop
nop
mov
nop
nop
mov
RTC0ADR, #0d0h
A, RTC0DAT
A, RTC0DAT
A, RTC0DAT
A, RTC0DAT
Recommended Instruction Timing for a multi-byte register write with short strobe enabled:
mov
mov
nop
mov
nop
mov
nop
mov
nop
196
RTC0ADR, #010h
RTC0DAT, #05h
RTC0DAT, #06h
RTC0DAT, #07h
RTC0DAT, #08h
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 20.1. RTC0KEY: SmaRTClock Lock and Key
Bit
7
6
5
4
3
Name
RTC0ST[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xAE
Bit
Name
7:0
RTC0ST
0
2
1
0
0
0
0
Function
SmaRTClock Interface Lock/Key and Status.
Locks/unlocks the SmaRTClock interface when written. Provides lock status when
read.
Read:
0x00: SmaRTClock Interface is locked.
0x01: SmaRTClock Interface is locked.
First key code (0xA5) has been written, waiting for second key code.
0x02: SmaRTClock Interface is unlocked.
First and second key codes (0xA5, 0xF1) have been written.
0x03: SmaRTClock Interface is disabled until the next system reset.
Write:
When RTC0ST = 0x00 (locked), writing 0xA5 followed by 0xF1 unlocks the
SmaRTClock Interface.
When RTC0ST = 0x01 (waiting for second key code), writing any value other
than the second key code (0xF1) will change RTC0STATE to 0x03 and disable
the SmaRTClock Interface until the next system reset.
When RTC0ST = 0x02 (unlocked), any write to RTC0KEY will lock the SmaRTClock Interface.
When RTC0ST = 0x03 (disabled), writes to RTC0KEY have no effect.
Rev. 1.3
197
Si1000/1/2/3/4/5
SFR Definition 20.2. RTC0ADR: SmaRTClock Address
Bit
7
6
Name
BUSY
AUTORD
Type
R/W
R/W
Reset
0
0
5
4
BUSY
2
SHORT
ADDR[3:0]
R
R/W
R/W
0
0
SFR Page = 0x0; SFR Address = 0xAC
Bit
Name
7
3
0
0
1
0
0
0
Function
SmaRTClock Interface Busy Indicator.
Indicates SmaRTClock interface status. Writing 1 to this bit initiates an indirect read.
6
AUTORD SmaRTClock Interface Autoread Enable.
Enables/disables Autoread.
0: Autoread Disabled.
1: Autoread Enabled.
5
Unused
Read = 0b; Write = Don’t Care.
4
SHORT
Short Strobe Enable.
Enables/disables the Short Strobe Feature.
0: Short Strobe disabled.
1: Short Strobe enabled.
3:0
ADDR[3:0] SmaRTClock Indirect Register Address.
Sets the currently selected SmaRTClock register.
See Table 20.1 for a listing of all SmaRTClock indirect registers.
Note: The ADDR bits increment after each indirect read/write operation that targets a CAPTUREn or ALARMn
internal SmaRTClock register.
198
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 20.3. RTC0DAT: SmaRTClock Data
Bit
7
6
5
4
3
Name
RTC0DAT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page= 0x0; SFR Address = 0xAD
Bit
Name
7:0
0
2
1
0
0
0
0
Function
RTC0DAT SmaRTClock Data Bits.
Holds data transferred to/from the internal SmaRTClock register selected by
RTC0ADR.
Note: Read-modify-write instructions (orl, anl, etc.) should not be used on this register.
Rev. 1.3
199
Si1000/1/2/3/4/5
20.2. SmaRTClock Clocking Sources
The SmaRTClock peripheral is clocked from its own timebase, independent of the system clock. The
SmaRTClock timebase is derived from the SmaRTClock oscillator circuit, which has two modes of operation: Crystal Mode, and Self-Oscillate Mode. The oscillation frequency is 32.768 kHz in Crystal Mode and
can be programmed in the range of 10 kHz to 40 kHz in Self-Oscillate Mode. The frequency of the SmaRTClock oscillator can be measured with respect to another oscillator using an on-chip timer. See Section
“27. Timers” on page 335 for more information on how this can be accomplished.
Note: The SmaRTClock timebase can be selected as the system clock and routed to a port pin. See Section
“19. Clocking Sources” on page 185 for information on selecting the system clock source and Section “21. Port
Input/Output” on page 210 for information on how to route the system clock to a port pin.
20.2.1. Using the SmaRTClock Oscillator with a Crystal or External CMOS Clock
When using Crystal Mode, a 32.768 kHz crystal should be connected between XTAL3 and XTAL4. No
other external components are required. The following steps show how to start the SmaRTClock crystal
oscillator in software:
1. Set SmaRTClock to Crystal Mode (XMODE = 1).
2. Disable Automatic Gain Control (AGCEN) and enable Bias Doubling (BIASX2) for fast crystal startup.
3. Set the desired loading capacitance (RTC0XCF).
4. Enable power to the SmaRTClock oscillator circuit (RTC0EN = 1).
5. Wait 20 ms.
6. Poll the SmaRTClock Clock Valid Bit (CLKVLD) until the crystal oscillator stabilizes.
7. Poll the SmaRTClock Load Capacitance Ready Bit (LOADRDY) until the load capacitance reaches its
programmed value.
8. Enable Automatic Gain Control (AGCEN) and disable Bias Doubling (BIASX2) for maximum power
savings.
9. Enable the SmaRTClock missing clock detector.
10.Wait 2 ms.
11. Clear the PMU0CF wake-up source flags.
In Crystal Mode, the SmaRTClock oscillator may be driven by an external CMOS clock. The CMOS clock
should be applied to XTAL3. XTAL4 should be left floating. The input low voltage (VIL) and input high voltage (VIH) for XTAL3 when used with an external CMOS clock are 0.1 and 0.8 V, respectively. The SmaRTClock oscillator should be configured to its lowest bias setting with AGC disabled. The CLKVLD bit is
indeterminate when using a CMOS clock, however, the OSCFAIL bit may be checked 2 ms after SmaRTClock oscillator is powered on to ensure that there is a valid clock on XTAL3.
20.2.2. Using the SmaRTClock Oscillator in Self-Oscillate Mode
When using Self-Oscillate Mode, the XTAL3 and XTAL4 pins should be shorted together. The RTC0PIN
register can be used to internally short XTAL3 and XTAL4. The following steps show how to configure
SmaRTClock for use in Self-Oscillate Mode:
1. Set SmaRTClock to Self-Oscillate Mode (XMODE = 0).
2. Set the desired oscillation frequency:
For oscillation at about 20 kHz, set BIASX2 = 0.
For oscillation at about 40 kHz, set BIASX2 = 1.
3. The oscillator starts oscillating instantaneously.
4. Fine tune the oscillation frequency by adjusting the load capacitance (RTC0XCF).
200
Rev. 1.3
Si1000/1/2/3/4/5
20.2.3. Programmable Load Capacitance
The programmable load capacitance has 16 values to support crystal oscillators with a wide range of recommended load capacitance. If Automatic Load Capacitance Stepping is enabled, the crystal load capacitors start at the smallest setting to allow a fast startup time, then slowly increase the capacitance until the
final programmed value is reached. The final programmed loading capacitor value is specified using the
LOADCAP bits in the RTC0XCF register. The LOADCAP setting specifies the amount of on-chip load
capacitance and does not include any stray PCB capacitance. Once the final programmed loading capacitor value is reached, the LOADRDY flag will be set by hardware to logic 1.
When using the SmaRTClock oscillator in Self-Oscillate mode, the programmable load capacitance can be
used to fine tune the oscillation frequency. In most cases, increasing the load capacitor value will result in
a decrease in oscillation frequency.Table 20.2 shows the crystal load capacitance for various settings of
LOADCAP.
.
Table 20.2. SmaRTClock Load Capacitance Settings
LOADCAP
Crystal Load Capacitance
Equivalent Capacitance seen on
XTAL3 and XTAL4
0000
4.0 pF
8.0 pF
0001
4.5 pF
9.0 pF
0010
5.0 pF
10.0 pF
0011
5.5 pF
11.0 pF
0100
6.0 pF
12.0 pF
0101
6.5 pF
13.0 pF
0110
7.0 pF
14.0 pF
0111
7.5 pF
15.0 pF
1000
8.0 pF
16.0 pF
1001
8.5 pF
17.0 pF
1010
9.0 pF
18.0 pF
1011
9.5 pF
19.0 pF
1100
10.5 pF
21.0 pF
1101
11.5 pF
23.0 pF
1110
12.5 pF
25.0 pF
1111
13.5 pF
27.0 pF
Rev. 1.3
201
Si1000/1/2/3/4/5
20.2.4. Automatic Gain Control (Crystal Mode Only) and SmaRTClock Bias Doubling
Automatic Gain Control allows the SmaRTClock oscillator to trim the oscillation amplitude of a crystal in
order to achieve the lowest possible power consumption. Automatic Gain Control automatically detects
when the oscillation amplitude has reached a point where it safe to reduce the drive current, therefore, it
may be enabled during crystal startup. It is recommended to enable Automatic Gain Control in most systems which use the SmaRTClock oscillator in Crystal Mode. The following are recommended crystal specifications and operating conditions when Automatic Gain Control is enabled:
ESR < 50 k
Load Capacitance < 10 pF
 Supply Voltage < 3.0 V
 Temperature > –20 °C
When using Automatic Gain Control, it is recommended to perform an oscillation robustness test to ensure
that the chosen crystal will oscillate under the worst case condition to which the system will be exposed.
The worst case condition that should result in the least robust oscillation is at the following system conditions: lowest temperature, highest supply voltage, highest ESR, highest load capacitance, and lowest bias
current (AGC enabled, Bias Double Disabled).


To perform the oscillation robustness test, the SmaRTClock oscillator should be enabled and selected as
the system clock source. Next, the SYSCLK signal should be routed to a port pin configured as a push-pull
digital output. The positive duty cycle of the output clock can be used as an indicator of oscillation robustness. As shown in Figure 20.2, duty cycles less than 55% indicate a robust oscillation. As the duty cycle
approaches 60%, oscillation becomes less reliable and the risk of clock failure increases. Increasing the
bias current (by disabling AGC) will always improve oscillation robustness and will reduce the output
clock’s duty cycle. This test should be performed at the worst case system conditions, as results at very
low temperatures or high supply voltage will vary from results taken at room temperature or low supply
voltage.
Safe Operating Zone
25%
Low Risk of Clock
Failure
55%
High Risk of Clock
Failure
60%
Duty Cycle
Figure 20.2. Interpreting Oscillation Robustness (Duty Cycle) Test Results
As an alternative to performing the oscillation robustness test, Automatic Gain Control may be disabled at
the cost of increased power consumption (approximately 200 nA). Disabling Automatic Gain Control will
provide the crystal oscillator with higher immunity against external factors which may lead to clock failure.
Automatic Gain Control must be disabled if using the SmaRTClock oscillator in self-oscillate mode.
Table 20.3 shows a summary of the oscillator bias settings. The SmaRTClock Bias Doubling feature allows
the self-oscillation frequency to be increased (almost doubled) and allows a higher crystal drive strength in
crystal mode. High crystal drive strength is recommended when the crystal is exposed to poor environmental conditions such as excessive moisture. SmaRTClock Bias Doubling is enabled by setting BIASX2
(RTC0XCN.5) to 1.
202
Rev. 1.3
Si1000/1/2/3/4/5
.
Table 20.3. SmaRTClock Bias Settings
Mode
Setting
Power
Consumption
Crystal
Bias Double Off, AGC On
Lowest
600 nA
Bias Double Off, AGC Off
Low
800 nA
Bias Double On, AGC On
High
Bias Double On, AGC Off
Highest
Bias Double Off
Low
Bias Double On
High
Self-Oscillate
20.2.5. Missing SmaRTClock Detector
The missing SmaRTClock detector is a one-shot circuit enabled by setting MCLKEN (RTC0CN.6) to 1.
When the SmaRTClock Missing Clock Detector is enabled, OSCFAIL (RTC0CN.5) is set by hardware if
SmaRTClock oscillator remains high or low for more than 100 µs.
A SmaRTClock Missing Clock detector timeout can trigger an interrupt, wake the device from a low power
mode, or reset the device. See Section “12. Interrupt Handler” on page 130, Section “14. Power Management” on page 152, and Section “18. Reset Sources” on page 178 for more information.
Note: The SmaRTClock Missing Clock Detector should be disabled when making changes to the oscillator settings in
RTC0XCN.
20.2.6. SmaRTClock Oscillator Crystal Valid Detector
The SmaRTClock oscillator crystal valid detector is an oscillation amplitude detector circuit used during
crystal startup to determine when oscillation has started and is nearly stable. The output of this detector
can be read from the CLKVLD bit (RTX0XCN.4).
Notes:
The CLKVLD bit has a blanking interval of 2 ms. During the first 2 ms after turning on the crystal
oscillator, the output of CLKVLD is not valid.
 This SmaRTClock crystal valid detector (CLKVLD) is not intended for detecting an oscillator failure. The
missing SmaRTClock detector (CLKFAIL) should be used for this purpose.

Rev. 1.3
203
Si1000/1/2/3/4/5
20.3. SmaRTClock Timer and Alarm Function
The SmaRTClock timer is a 32-bit counter that, when running (RTC0TR = 1), is incremented every
SmaRTClock oscillator cycle. The timer has an alarm function that can be set to generate an interrupt,
wake the device from a low power mode, or reset the device at a specific time. See Section “12. Interrupt
Handler” on page 130, Section “14. Power Management” on page 152, and Section “18. Reset Sources”
on page 178 for more information.
The SmaRTClock timer includes an Auto Reset feature, which automatically resets the timer to zero one
SmaRTClock cycle after the alarm signal is deasserted. When using Auto Reset, the Alarm match value
should always be set to 2 counts less than the desired match value. Auto Reset can be enabled by writing
a 1 to ALRM (RTC0CN.2).
20.3.1. Setting and Reading the SmaRTClock Timer Value
The 32-bit SmaRTClock timer can be set or read using the six CAPTUREn internal registers. Note that the
timer does not need to be stopped before reading or setting its value. The following steps can be used to
set the timer value:
1. Write the desired 32-bit set value to the CAPTUREn registers.
2. Write 1 to RTC0SET. This will transfer the contents of the CAPTUREn registers to the SmaRTClock
timer.
3. Operation is complete when RTC0SET is cleared to 0 by hardware.
The following steps can be used to read the current timer value:
1. Write 1 to RTC0CAP. This will transfer the contents of the timer to the CAPTUREn registers.
2. Poll RTC0CAP until it is cleared to 0 by hardware.
3. A snapshot of the timer value can be read from the CAPTUREn registers
20.3.2. Setting a SmaRTClock Alarm
The SmaRTClock alarm function compares the 32-bit value of SmaRTClock Timer to the value of the
ALARMn registers. An alarm event is triggered if the SmaRTClock timer is equal to the ALARMn registers.
If Auto Reset is enabled, the 32-bit timer will be cleared to zero one SmaRTClock cycle after the alarm
event.
The SmaRTClock alarm event can be configured to reset the MCU, wake it up from a low power mode, or
generate an interrupt. See Section “12. Interrupt Handler” on page 130, Section “14. Power Management”
on page 152, and Section “18. Reset Sources” on page 178 for more information.
The following steps can be used to set up a SmaRTClock Alarm:
1. Disable SmaRTClock Alarm Events (RTC0AEN = 0).
2. Set the ALARMn registers to the desired value.
3. Enable SmaRTClock Alarm Events (RTC0AEN = 1).
Notes:
The ALRM bit, which is used as the SmaRTClock Alarm Event flag, is cleared by disabling
SmaRTClock Alarm Events (RTC0AEN = 0).
 If AutoReset is disabled, disabling (RTC0AEN = 0) then Re-enabling Alarm Events (RTC0AEN = 1)
after a SmaRTClock Alarm without modifying ALARMn registers will automatically schedule the next
alarm after 2^32 SmaRTClock cycles (approximately 36 hours using a 32.768 kHz crystal).
 The SmaRTClock Alarm Event flag will remain asserted for a maximum of one SmaRTClock cycle. See
Section “14. Power Management” on page 152 for information on how to capture a SmaRTClock Alarm
event using a flag which is not automatically cleared by hardware.

204
Rev. 1.3
Si1000/1/2/3/4/5
20.3.3. Software Considerations for using the SmaRTClock Timer and Alarm
The SmaRTClock timer and alarm have two operating modes to suit varying applications. The two modes
are described below:
Mode 1:
The first mode uses the SmaRTClock timer as a perpetual timebase which is never reset to zero. Every 36
hours, the timer is allowed to overflow without being stopped or disrupted. The alarm interval is software
managed and is added to the ALRMn registers by software after each alarm. This allows the alarm match
value to always stay ahead of the timer by one software managed interval. If software uses 32-bit unsigned
addition to increment the alarm match value, then it does not need to handle overflows since both the timer
and the alarm match value will overflow in the same manner.
This mode is ideal for applications which have a long alarm interval (e.g. 24 or 36 hours) and/or have a
need for a perpetual timebase. An example of an application that needs a perpetual timebase is one
whose wake-up interval is constantly changing. For these applications, software can keep track of the
number of timer overflows in a 16-bit variable, extending the 32-bit (36 hour) timer to a 48-bit (272 year)
perpetual timebase.
Mode 2:
The second mode uses the SmaRTClock timer as a general purpose up counter which is auto reset to zero
by hardware after each alarm. The alarm interval is managed by hardware and stored in the ALRMn registers. Software only needs to set the alarm interval once during device initialization. After each alarm, software should keep a count of the number of alarms that have occurred in order to keep track of time.
This mode is ideal for applications that require minimal software intervention and/or have a fixed alarm
interval. This mode is the most power efficient since it requires less CPU time per alarm.
Rev. 1.3
205
Si1000/1/2/3/4/5
Internal Register Definition 20.4. RTC0CN: SmaRTClock Control
Bit
7
6
5
4
3
2
Name
RTC0EN
MCLKEN
OSCFAIL
RTC0TR
RTC0AEN
ALRM
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
Varies
0
0
0
0
0
SmaRTClock Address = 0x04
Bit
Name
7
RTC0EN SmaRTClock Enable.
1
RTC0SET RTC0CAP
Function
6
Enables/disables the SmaRTClock oscillator and associated bias currents.
0: SmaRTClock oscillator disabled.
1: SmaRTClock oscillator enabled.
MCLKEN Missing SmaRTClock Detector Enable.
5
Enables/disables the missing SmaRTClock detector.
0: Missing SmaRTClock detector disabled.
1: Missing SmaRTClock detector enabled.
OSCFAIL SmaRTClock Oscillator Fail Event Flag.
4
3
RTC0TR
0
Set by hardware when a missing SmaRTClock detector timeout occurs. Must be
cleared by software. The value of this bit is not defined when the SmaRTClock 
oscillator is disabled.
SmaRTClock Timer Run Control.
Controls if the SmaRTClock timer is running or stopped (holds current value).
0: SmaRTClock timer is stopped.
1: SmaRTClock timer is running.
RTC0AEN SmaRTClock Alarm Enable.
1
Enables/disables the SmaRTClock alarm function. Also clears the ALRM flag.
0: SmaRTClock alarm disabled.
1: SmaRTClock alarm enabled.
Write:
ALRM
SmaRTClock Alarm Event Read:
Flag and Auto Reset
0: Disable Auto Reset.
0: SmaRTClock alarm
Enable
event flag is de-asserted. 1: Enable Auto Reset.
Reads return the state of the 1: SmaRTClock alarm
event flag is asserted.
alarm event flag.
Writes enable/disable the 
Auto Reset function.
RTC0SET SmaRTClock Timer Set.
0
Writing 1 initiates a SmaRTClock timer set operation. This bit is cleared to 0 by hardware to indicate that the timer set operation is complete.
RTC0CAP SmaRTClock Timer Capture.
2
Writing 1 initiates a SmaRTClock timer capture operation. This bit is cleared to 0 by
hardware to indicate that the timer capture operation is complete.
Note: The ALRM flag will remain asserted for a maximum of one SmaRTClock cycle. See Section “Power
Management” on page 152 for information on how to capture a SmaRTClock Alarm event using a flag which is
not automatically cleared by hardware.
206
Rev. 1.3
Si1000/1/2/3/4/5
Internal Register Definition 20.5. RTC0XCN: SmaRTClock Oscillator Control
Bit
7
6
5
4
3
2
1
0
Name
AGCEN
XMODE
BIASX2
CLKVLD
Type
R/W
R/W
R/W
R
R
R
R
R
Reset
0
0
0
0
0
0
0
0
SmaRTClock Address = 0x05
Bit
Name
7
AGCEN
Function
SmaRTClock Oscillator Automatic Gain Control (AGC) Enable.
0: AGC disabled.
1: AGC enabled.
6
XMODE
SmaRTClock Oscillator Mode.
Selects Crystal or Self Oscillate Mode.
0: Self-Oscillate Mode selected.
1: Crystal Mode selected.
5
BIASX2
SmaRTClock Oscillator Bias Double Enable.
Enables/disables the Bias Double feature.
0: Bias Double disabled.
1: Bias Double enabled.
4
CLKVLD
SmaRTClock Oscillator Crystal Valid Indicator.
Indicates if oscillation amplitude is sufficient for maintaining oscillation.
0: Oscillation has not started or oscillation amplitude is too low to maintain oscillation.
1: Sufficient oscillation amplitude detected.
3:0
Unused
Read = 0000b; Write = Don’t Care.
Rev. 1.3
207
Si1000/1/2/3/4/5
Internal Register Definition 20.6. RTC0XCF: SmaRTClock Oscillator Configuration
Bit
7
6
Name AUTOSTP
5
4
3
LOADRDY
R/W
R
R
R
Reset
0
0
0
0
0
R/W
Varies
SmaRTClock Address = 0x06
Bit
Name
AUTOSTP
1
LOADCAP
Type
7
2
Varies
Varies
Varies
Function
Automatic Load Capacitance Stepping Enable.
Enables/disables automatic load capacitance stepping.
0: Load capacitance stepping disabled.
1: Load capacitance stepping enabled.
6
LOADRDY
Load Capacitance Ready Indicator.
Set by hardware when the load capacitance matches the programmed value.
0: Load capacitance is currently stepping.
1: Load capacitance has reached it programmed value.
5:4
Unused
Read = 00b; Write = Don’t Care.
3:0
LOADCAP
Load Capacitance Programmed Value.
Holds the user’s desired value of the load capacitance. See Table 20.2 on
page 201.
Internal Register Definition 20.7. RTC0PIN: SmaRTClock Pin Configuration
Bit
7
6
5
4
Name
RTC0PIN
Type
W
Reset
0
1
1
0
SmaRTClock Address = 0x07
Bit
Name
7:0
3
2
1
0
0
1
1
1
Function
RTC0PIN SmaRTClock Pin Configuration.
Writing 0xE7 to this register forces XTAL3 and XTAL4 to be internally shorted for use
with Self Oscillate Mode.
Writing 0x67 returns XTAL3 and XTAL4 to their normal configuration.
208
Rev. 1.3
Si1000/1/2/3/4/5
Internal Register Definition 20.8. CAPTUREn: SmaRTClock Timer Capture
Bit
7
6
5
4
3
2
1
0
CAPTURE[31:0]
Name
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SmaRTClock Addresses: CAPTURE0 = 0x00; CAPTURE1 = 0x01; CAPTURE2 =0x02; CAPTURE3: 0x03.
Bit
Name
Function
7:0
CAPTURE[31:0] SmaRTClock Timer Capture.
These 4 registers (CAPTURE3–CAPTURE0) are used to read or set the 32-bit
SmaRTClock timer. Data is transferred to or from the SmaRTClock timer when
the RTC0SET or RTC0CAP bits are set.
Note: The least significant bit of the timer capture value is in CAPTURE0.0.
Internal Register Definition 20.9. ALARMn: SmaRTClock Alarm Programmed Value
Bit
7
6
5
4
3
2
1
0
ALARM[31:0]
Name
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SmaRTClock Addresses: ALARM0 = 0x08; ALARM1 = 0x09; ALARM2 = 0x0A; ALARM3 = 0x0B
Bit
Name
Function
7:0
ALARM[31:0] SmaRTClock Alarm Programmed Value.
These 4 registers (ALARM3–ALARM0) are used to set an alarm event for the
SmaRTClock timer. The SmaRTClock alarm should be disabled (RTC0AEN=0)
when updating these registers.
Note: The least significant bit of the alarm programmed value is in ALARM0.0.
Rev. 1.3
209
Si1000/1/2/3/4/5
21. Port Input/Output
Digital and analog resources are available through 19 or 16 I/O pins. The EZRadioPRO peripheral provides an additional 3 GPIO pins which are independent of the pins described in this chapter. Port pins are
organized as three byte-wide ports. Port pins P0.0–P2.6 can be defined as digital or analog I/O. Digital I/O
pins can be assigned to one of the internal digital resources or used as general purpose I/O (GPIO). Analog I/O pins are used by the internal analog resources. P1.0, P1.1, P1.2, and P1.4 are dedicated for communication with the EZRadioPRO peripheral. P1.3 is not available. P2.4, P2.5, and P2.6 are only available
on the Si1000/1/2/3. P2.7 can be used as GPIO and is shared with the C2 Interface Data signal (C2D).
See Section “29. Device Specific Behavior” on page 376 for more details.
The designer has complete control over which digital and analog functions are assigned to individual Port
pins, limited only by the number of physical I/O pins. This resource assignment flexibility is achieved
through the use of a Priority Crossbar Decoder. See Section 21.3 for more information on the Crossbar.
All Px.x Port I/Os are 5V tolerant when used as digital inputs or open-drain outputs. For Port I/Os configured as push-pull outputs, current is sourced from the VDD_MCU supply. Port I/Os used for analog functions can operate up to the VDD_MCU supply voltage. See Section 21.1 for more information on Port I/O
operating modes and the electrical specifications chapter for detailed electrical specifications.
XBR0, XBR1,
XBR2, PnSKIP
Registers
Port Match
P0MASK, P0MAT
P1MASK, P1MAT
External Interrupts
EX0 and EX1
Priority
Decoder
Highest
Priority
UART
4
(Internal Digital Signals)
SPI0
SPI1
SMBus
CP0
CP1
Outputs
P0.0
2
Digital
Crossbar
8
4
8
7
T0, T1
P0
I/O
Cells
P0.7
SYSCLK
PCA
Lowest
Priority
PnMDOUT,
PnMDIN Registers
2
P1.5
P1
I/O
Cells
P1.7
2
8
(Port Latches)
P0
8
(P0.0-P0.7)
8
P1
(P1.0-P1.7)
8
P2
(P2.0-P2.7)
P2.0
P2
I/O
Cell
P2.6
P2.7
To Analog Peripherals
(ADC0, CP0, and CP1 inputs,
VREF, IREF0, AGND)
No analog functionality
available on P2.7
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the
EZRadioPRO peripheral. P1.3 is not internally or externally connected.
P2.4, P2.5, and P2.6 are only available on Si1000/1/2/3
Figure 21.1. Port I/O Functional Block Diagram
210
P1.6
Rev. 1.3
Si1000/1/2/3/4/5
21.1. Port I/O Modes of Operation
Port pins P0.0–P2.6 use the Port I/O cell shown in Figure 21.2. Each Port I/O cell can be configured by
software for analog I/O or digital I/O using the PnMDIN registers. On reset, all Port I/O cells default to a digital high impedance state with weak pull-ups enabled.
21.1.1. Port Pins Configured for Analog I/O
Any pins to be used as Comparator or ADC input, external oscillator input/output, or AGND, VREF, or Current Reference output should be configured for analog I/O (PnMDIN.n = 0). When a pin is configured for
analog I/O, its weak pullup and digital receiver are disabled. In most cases, software should also disable
the digital output drivers. Port pins configured for analog I/O will always read back a value of 0 regardless
of the actual voltage on the pin.
Configuring pins as analog I/O saves power and isolates the Port pin from digital interference. Port pins
configured as digital inputs may still be used by analog peripherals; however, this practice is not recommended and may result in measurement errors.
21.1.2. Port Pins Configured For Digital I/O
Any pins to be used by digital peripherals (UART, SPI, SMBus, etc.), external digital event capture functions, or as GPIO should be configured as digital I/O (PnMDIN.n = 1). For digital I/O pins, one of two output
modes (push-pull or open-drain) must be selected using the PnMDOUT registers.
Push-pull outputs (PnMDOUT.n = 1) drive the Port pad to the VDD_MCU or GND supply rails based on the
output logic value of the Port pin. Open-drain outputs have the high side driver disabled; therefore, they
only drive the Port pad to GND when the output logic value is 0 and become high impedance inputs (both
high and low drivers turned off) when the output logic value is 1.
When a digital I/O cell is placed in the high impedance state, a weak pull-up transistor pulls the Port pad to
the VDD_MCU supply voltage to ensure the digital input is at a defined logic state. Weak pull-ups are disabled when the I/O cell is driven to GND to minimize power consumption and may be globally disabled by
setting WEAKPUD to 1. The user must ensure that digital I/O are always internally or externally pulled or
driven to a valid logic state. Port pins configured for digital I/O always read back the logic state of the Port
pad, regardless of the output logic value of the Port pin.
WEAKPUD
(Weak Pull-Up Disable)
PnMDOUT.x
(1 for push-pull)
(0 for open-drain)
VDD/DC+
VDD/DC+
XBARE
(Crossbar
Enable)
(WEAK)
PORT
PAD
Pn.x – Output
Logic Value
(Port Latch or
Crossbar)
PnMDIN.x
(1 for digital)
(0 for analog)
To/From Analog
Peripheral
GND
Pn.x – Input Logic Value
(Reads 0 when pin is configured as an analog I/O)
Figure 21.2. Port I/O Cell Block Diagram
Rev. 1.3
211
Si1000/1/2/3/4/5
21.1.3. Interfacing Port I/O to 5 V and 3.3 V Logic
All Port I/O configured for digital, open-drain operation are capable of interfacing to digital logic operating at
a supply voltage higher than 4.5 V and less than 5.25 V. When the supply voltage is in the range of 1.8 to
2.2 V, the I/O may also interface to digital logic operating between 3.0 to 3.6 V if the input signal frequency
is less than 12.5 MHz or less than 25 MHz if the signal rise time (10% to 90%) is less than 1.2 ns. When
operating at a supply voltage above 2.2 V, the device should not interface to 3.3 V logic; however, interfacing to 5 V logic is permitted. An external pull-up resistor to the higher supply voltage is typically required for
most systems.
Important Notes:
When interfacing to a signal that is between 4.5 and 5.25 V, the maximum clock frequency that may be
input on a GPIO pin is 12.5 MHz. The exception to this rule is when routing an external CMOS clock to
P0.3, in which case, a signal up to 25 MHz is valid as long as the rise time (10% to 90%) is shorter than
1.8 ns.
 When the supply voltage is less than 2.2 V and interfacing to a signal that is between 3.0 and 3.6 V, the
maximum clock frequency that may be input on a GPIO pin is 3.125 MHz. The exception to this rule is
when routing an external CMOS clock to P0.3, in which case, a signal up to 25 MHz is valued as long
as the rise time (10% to 90%) is shorter than 1.2 ns.
 In a multi-voltage interface, the external pull-up resistor should be sized to allow a current of at least
150 µA to flow into the Port pin when the supply voltage is between (VDD_MCU/DC+ plus 0.4 V) and
(VDD_MCU/DC+ plus 1.0 V). Once the Port pad voltage increases beyond this range, the current
flowing into the Port pin is minimal.
These guidelines only apply to multi-voltage interfaces. Port I/Os may always interface to digital logic operating at the same supply voltage.

21.1.4. Increasing Port I/O Drive Strength
Port I/O output drivers support a high and low drive strength; the default is low drive strength. The drive
strength of a Port I/O can be configured using the PnDRV registers. See Section “4. Electrical Characteristics” on page 40 for the difference in output drive strength between the two modes.
21.2. Assigning Port I/O Pins to Analog and Digital Functions
Port I/O pins P0.0–P2.6 can be assigned to various analog, digital, and external interrupt functions. The
Port pins assuaged to analog functions should be configured for analog I/O and Port pins assuaged to digital or external interrupt functions should be configured for digital I/O.
21.2.1. Assigning Port I/O Pins to Analog Functions
Table 21.1 shows all available analog functions that need Port I/O assignments. Port pins selected for
these analog functions should have their digital drivers disabled (PnMDOUT.n = 0 and Port Latch =
1) and their corresponding bit in PnSKIP set to 1. This reserves the pin for use by the analog function
and does not allow it to be claimed by the Crossbar. Table 21.1 shows the potential mapping of Port I/O to
each analog function.
212
Rev. 1.3
Si1000/1/2/3/4/5
Table 21.1. Port I/O Assignment for Analog Functions
Analog Function
Potentially
Assignable Port Pins
SFR(s) used for
Assignment
ADC Input
P0.0–P2.6
ADC0MX, PnSKIP
Comparator0 Input
P0.0–P2.6
CPT0MX, PnSKIP
Comparator1 Input
P0.0–P2.6
CPT1MX, PnSKIP
Voltage Reference (VREF0)
P0.0
REF0CN, PnSKIP
Analog Ground Reference (AGND)
P0.1
REF0CN, PnSKIP
Current Reference (IREF0)
P0.7
IREF0CN, PnSKIP
External Oscillator Input (XTAL1)
P0.2
OSCXCN, PnSKIP
External Oscillator Output (XTAL2)
P0.3
OSCXCN, PnSKIP
21.2.2. Assigning Port I/O Pins to Digital Functions
Any Port pins not assigned to analog functions may be assigned to digital functions or used as GPIO. Most
digital functions rely on the Crossbar for pin assignment; however, some digital functions bypass the
Crossbar in a manner similar to the analog functions listed above. Port pins used by these digital functions and any Port pins selected for use as GPIO should have their corresponding bit in PnSKIP set
to 1. Table 21.2 shows all available digital functions and the potential mapping of Port I/O to each digital
function.
Table 21.2. Port I/O Assignment for Digital Functions
Digital Function
UART0, SPI1, SPI0, SMBus,
CP0 and CP1 Outputs, System Clock Output, PCA0,
Timer0 and Timer1 External
Inputs.
Any pin used for GPIO
Potentially Assignable Port Pins
SFR(s) used for
Assignment
Any Port pin available for assignment by the
Crossbar. This includes P0.0–P2.6 pins which
have their PnSKIP bit set to 0.
Note: The Crossbar will always assign UART0
and SPI1 pins to fixed locations.
XBR0, XBR1, XBR2
P0.0–P2.6
P0SKIP, P1SKIP,
P2SKIP
21.2.3. Assigning Port I/O Pins to External Digital Event Capture Functions
External digital event capture functions can be used to trigger an interrupt or wake the device from a low
power mode when a transition occurs on a digital I/O pin. The digital event capture functions do not require
dedicated pins and will function on both GPIO pins (PnSKIP = 1) and pins in use by the Crossbar (PnSKIP
= 0). External digital even capture functions cannot be used on pins configured for analog I/O. Table 21.3
shows all available external digital event capture functions.
Rev. 1.3
213
Si1000/1/2/3/4/5
Table 21.3. Port I/O Assignment for External Digital Event Capture Functions
Digital Function
Potentially Assignable Port Pins
SFR(s) used for
Assignment
External Interrupt 0
P0.0–P0.7
IT01CF
External Interrupt 1
P0.0–P0.7
IT01CF
Port Match
P0.0–P1.7
P0MASK, P0MAT
P1MASK, P1MAT
21.3. Priority Crossbar Decoder
The Priority Crossbar Decoder assigns a Port I/O pin to each software selected digital function using the
fixed peripheral priority order shown in Figure 21.3. The registers XBR0, XBR1, and XBR2 defined in SFR
Definition 21.1, SFR Definition 21.2, and SFR Definition 21.3 are used to select digital functions in the
Crossbar. The Port pins available for assignment by the Crossbar include all Port pins (P0.0–P2.6) which
have their corresponding bit in PnSKIP set to 0.
From Figure 21.3, the highest priority peripheral is UART0. If UART0 is selected in the Crossbar (using the
XBRn registers), then P0.4 and P0.5 will be assigned to UART0. The next highest priority peripheral is
SPI1. If SPI1 is selected in the Crossbar, then P1.0–P1.2 will be assigned to SPI1. P1.3 will be assigned if
SPI1 is configured for 4-wire mode. The user should ensure that the pins to be assigned by the Crossbar
have their PnSKIP bits set to 0.
For all remaining digital functions selected in the Crossbar, starting at the top of Figure 21.3 going down,
the least-significant unskipped, unassigned Port pin(s) are assigned to that function. If a Port pin is already
assigned (e.g., UART0 or SPI1 pins), or if its PnSKIP bit is set to 1, then the Crossbar will skip over the pin
and find next available unskipped, unassigned Port pin. All Port pins used for analog functions, GPIO, or
dedicated digital functions such as the EMIF should have their PnSKIP bit set to 1.
Figure 21.3 shows the Crossbar Decoder priority with no Port pins skipped (P0SKIP, P1SKIP, P2SKIP =
0x00); Figure 21.4 shows the Crossbar Decoder priority with the External Oscillator pins (XTAL1 and
XTAL2) skipped (P0SKIP = 0x0C).
Notes:
The Crossbar must be enabled (XBARE = 1) before any Port pin is used as a digital output. Port output
drivers are disabled while the Crossbar is disabled.
 When SMBus is selected in the Crossbar, the pins associated with SDA and SCL will automatically be
forced into open-drain output mode regardless of the PnMDOUT setting.
 SPI0 can be operated in either 3-wire or 4-wire modes, depending on the state of the NSSMD1NSSMD0 bits in register SPI0CN. The NSS signal is only routed to a Port pin when 4-wire mode is
selected. When SPI0 is selected in the Crossbar, the SPI0 mode (3-wire or 4-wire) will affect the pinout
of all digital functions lower in priority than SPI0.
 For given XBRn, PnSKIP, and SPInCN register settings, one can determine the I/O pin-out of the
device using Figure 21.3 and Figure 21.4.

214
Rev. 1.3
Si1000/1/2/3/4/5
3
4
5
6
7
0
1
2
C2D
2
3
4
EZRadioPRO Slave Select
XTAL2
1
P2
EZRadioPRO
Serial
Interface
No Connect
XTAL1
0
IREF0
AGND
PIN I/O
P1
CNVSTR
SF Signals
VREF
P0
5
6
7
0
1 2
3
4 5 6 7
TX0
RX0
SCK (SPI1)
MISO (SPI1)
MOSI (SPI1)
SCK (SPI0)
MISO (SPI0)
MOSI (SPI0)
(*4-Wire SPI Only)
NSS* (SPI0)
SDA
SCL
CP0
CP0A
CP1
CP1A
/SYSCLK
CEX0
CEX1
CEX2
CEX3
CEX4
CEX5
ECI
T0
T1
0
0
0
0
0
0
P0SKIP[0:7]
0
0
0
0
0
1
1
0
P1SKIP[0:7]
0
0
0
0 0
0
0 0 0 X
P2SKIP[0:7]
Figure 21.3. Crossbar Priority Decoder with No Pins Skipped
Rev. 1.3
215
Si1000/1/2/3/4/5
3
4
5
6
7
0 1
2
C2D
2
3
4
EZRadioPRO Slave Select
XTAL2
1
P2
EZRadioPRO
Serial
Interface
No Connect
XTAL1
0
IREF0
AGND
PIN I/O
P1
CNVSTR
SF Signals
VREF
P0
5
6
7
0 1 2 3 4 5 6 7
TX0
RX0
SCK (SPI1)
MISO (SPI1)
MOSI (SPI1)
NSS* (SPI1)
SCK (SPI0)
MISO (SPI0)
MOSI (SPI0)
(*4-Wire SPI Only)
NSS* (SPI0)
SDA
SCL
CP0
CP0A
CP1
CP1A
/SYSCLK
CEX0
CEX1
CEX2
CEX3
CEX4
CEX5
ECI
T0
T1
0
0
0
0
0
0
P0SKIP[0:7]
0
0
0 0
0
1
1
0
P1SKIP[0:7]
0
0
0 0 0 0 0 0 0 X
P2SKIP[0:7]
Figure 21.4. Crossbar Priority Decoder with Crystal Pins Skipped
216
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 21.1. XBR0: Port I/O Crossbar Register 0
Bit
7
6
5
4
3
2
1
0
Name
CP1AE
CP1E
CP0AE
CP0E
SYSCKE
SMB0E
SPI0E
URT0E
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xE1
Bit
Name
7
CP1AE
Function
Comparator1 Asynchronous Output Enable.
0: Asynchronous CP1 output unavailable at Port pin.
1: Asynchronous CP1 output routed to Port pin.
6
CP1E
Comparator1 Output Enable.
0: CP1 output unavailable at Port pin.
1: CP1 output routed to Port pin.
5
CP0AE
Comparator0 Asynchronous Output Enable.
0: Asynchronous CP0 output unavailable at Port pin.
1: Asynchronous CP0 output routed to Port pin.
4
CP0E
Comparator0 Output Enable.
0: CP1 output unavailable at Port pin.
1: CP1 output routed to Port pin.
3
SYSCKE SYSCLK Output Enable.
0: SYSCLK output unavailable at Port pin.
1: SYSCLK output routed to Port pin.
2
SMB0E
SMBus I/O Enable.
0: SMBus I/O unavailable at Port pin.
1: SDA and SCL routed to Port pins.
1
SPI0E
SPI0 I/O Enable
0: SPI0 I/O unavailable at Port pin.
1: SCK, MISO, and MOSI (for SPI0) routed to Port pins.
NSS (for SPI0) routed to Port pin only if SPI0 is configured to 4-wire mode.
0
URT0E
UART0 Output Enable.
0: UART I/O unavailable at Port pin.
1: TX0 and RX0 routed to Port pins P0.4 and P0.5.
Note: SPI0 can be assigned either 3 or 4 Port I/O pins.
Rev. 1.3
217
Si1000/1/2/3/4/5
SFR Definition 21.2. XBR1: Port I/O Crossbar Register 1
Bit
7
Name
6
5
4
3
SPI1E
T1E
T0E
ECIE
2
1
0
PCA0ME[2:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xE2
Bit
Name
7
Unused
6
SPI1E
Function
Read = 0b; Write = Don’t Care.
EZRadioPRO Serial Interface (SPI1) Enable.
0: EZRadioPRO peripheral unavailable.
1: SCK (for EZRadioPRO) routed to P1.0.
MISO (for EZRadioPRO) routed to P1.1.
MOSI (for EZRadioPRO) routed to P1.2.
NSS (for EZRadioPRO) routed to P1.3 only if SPI1 is configured to 4-wire mode.
Note: When communicating with EZRadioPRO, the SPI1 should be configured to 3wire mode and P1.4 should be used as a standard Port I/O pin to control NSS.
5
T1E
Timer1 Input Enable.
0: T1 input unavailable at Port pin.
1: T1 input routed to Port pin.
4
T0E
Timer0 Input Enable.
0: T0 input unavailable at Port pin.
1: T0 input routed to Port pin.
3
ECIE
PCA0 External Counter Input (ECI) Enable.
0: PCA0 external counter input unavailable at Port pin.
1: PCA0 external counter input routed to Port pin.
2:0
PCA0ME PCA0 Module I/O Enable.
000: All PCA0 I/O unavailable at Port pin.
001: CEX0 routed to Port pin.
010: CEX0, CEX1 routed to Port pins.
011: CEX0, CEX1, CEX2 routed to Port pins.
100: CEX0, CEX1, CEX2 CEX3 routed to Port pins.
101: CEX0, CEX1, CEX2, CEX3, CEX4 routed to Port pins.
110: CEX0, CEX1, CEX2, CEX3, CEX4, CEX5 routed to Port pins.
111: Reserved.
Note: SPI1 can be assigned either 3 or 4 Port I/O pins.
218
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 21.3. XBR2: Port I/O Crossbar Register 2
Bit
7
6
5
4
3
2
1
0
Name
WEAKPUD
XBARE
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xE3
Bit
7
Name
Function
WEAKPUD Port I/O Weak Pullup Disable
0: Weak Pullups enabled (except for Port I/O pins configured for analog mode).
6
XBARE
Crossbar Enable
0: Crossbar disabled.
1: Crossbar enabled.
5:0
Unused
Read = 000000b; Write = Don’t Care.
Note: The Crossbar must be enabled (XBARE = 1) to use any Port pin as a digital output.
21.4. Port Match
Port match functionality allows system events to be triggered by a logic value change on P0 or P1. A software controlled value stored in the PnMAT registers specifies the expected or normal logic values of P0
and P1. A Port mismatch event occurs if the logic levels of the Port’s input pins no longer match the software controlled value. This allows Software to be notified if a certain change or pattern occurs on P0 or P1
input pins regardless of the XBRn settings.
The PnMASK registers can be used to individually select which P0 and P1 pins should be compared
against the PnMAT registers. A Port mismatch event is generated if (P0 & P0MASK) does not equal
(PnMAT & P0MASK) or if (P1 & P1MASK) does not equal (PnMAT & P1MASK).
A Port mismatch event may be used to generate an interrupt or wake the device from a low power mode.
See Section “12. Interrupt Handler” on page 130 and Section “14. Power Management” on page 152 for
more details on interrupt and wake-up sources.
Rev. 1.3
219
Si1000/1/2/3/4/5
SFR Definition 21.4. P0MASK: Port0 Mask Register
Bit
7
6
5
4
3
Name
P0MASK[7:0]
Type
R/W
Reset
0
0
0
0
0
2
1
0
0
0
0
SFR Page= 0x0; SFR Address = 0xC7
Bit
7:0
Name
Function
P0MASK[7:0] Port0 Mask Value.
Selects the P0 pins to be compared with the corresponding bits in P0MAT.
0: P0.n pin pad logic value is ignored and cannot cause a Port Mismatch event.
1: P0.n pin pad logic value is compared to P0MAT.n.
SFR Definition 21.5. P0MAT: Port0 Match Register
Bit
7
6
5
4
3
Name
P0MAT[7:0]
Type
R/W
Reset
1
1
1
1
1
2
1
0
1
1
1
SFR Page= 0x0; SFR Address = 0xD7
Bit
7 :0
Name
Function
P0MAT[7:0] Port 0 Match Value.
Match comparison value used on Port 0 for bits in P0MASK which are set to 1.
0: P0.n pin logic value is compared with logic LOW.
1: P0.n pin logic value is compared with logic HIGH.
220
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 21.6. P1MASK: Port1 Mask Register
Bit
7
6
5
4
3
Name
P1MASK[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Page= 0x0; SFR Address = 0xBF
Bit
Name
7:0
2
1
0
0
0
0
Function
P1MASK[7:0] Port 1 Mask Value.
Selects P1 pins to be compared to the corresponding bits in P1MAT.
0: P1.n pin logic value is ignored and cannot cause a Port Mismatch event.
1: P1.n pin logic value is compared to P1MAT.n.
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the EZRadioPRO peripheral. P1.3 is not externally or
internally connected.
SFR Definition 21.7. P1MAT: Port1 Match Register
Bit
7
6
5
4
3
Name
P1MAT[7:0]
Type
R/W
Reset
1
1
1
1
SFR Page = 0x0; SFR Address = 0xCF
Bit
Name
7:0
1
2
1
0
1
1
1
Function
P1MAT[7:0] Port 1 Match Value.
Match comparison value used on Port 1 for bits in P1MASK which are set to 1.
0: P1.n pin logic value is compared with logic LOW.
1: P1.n pin logic value is compared with logic HIGH.
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the EZRadioPRO peripheral. P1.3 is not externally or
internally connected.
Rev. 1.3
221
Si1000/1/2/3/4/5
21.5. Special Function Registers for Accessing and Configuring Port I/O
All Port I/O are accessed through corresponding special function registers (SFRs) that are both byte
addressable and bit addressable. When writing to a Port, the value written to the SFR is latched to maintain the output data value at each pin. When reading, the logic levels of the Port's input pins are returned
regardless of the XBRn settings (i.e., even when the pin is assigned to another signal by the Crossbar, the
Port register can always read its corresponding Port I/O pin). The exception to this is the execution of the
read-modify-write instructions that target a Port Latch register as the destination. The read-modify-write
instructions when operating on a Port SFR are the following: ANL, ORL, XRL, JBC, CPL, INC, DEC, DJNZ
and MOV, CLR or SETB, when the destination is an individual bit in a Port SFR. For these instructions, the
value of the latch register (not the pin) is read, modified, and written back to the SFR.
Each Port has a corresponding PnSKIP register which allows its individual Port pins to be assigned to digital functions or skipped by the Crossbar. All Port pins used for analog functions, GPIO, or dedicated digital
functions such as the EMIF should have their PnSKIP bit set to 1.
The Port input mode of the I/O pins is defined using the Port Input Mode registers (PnMDIN). Each Port
cell can be configured for analog or digital I/O. This selection is required even for the digital resources
selected in the XBRn registers, and is not automatic. The only exception to this is P2.7, which can only be
used for digital I/O.
The output driver characteristics of the I/O pins are defined using the Port Output Mode registers (PnMDOUT). Each Port Output driver can be configured as either open drain or push-pull. This selection is
required even for the digital resources selected in the XBRn registers, and is not automatic. The only
exception to this is the SMBus (SDA, SCL) pins, which are configured as open-drain regardless of the
PnMDOUT settings.
The drive strength of the output drivers are controlled by the Port Drive Strength (PnDRV) registers. The
default is low drive strength. See Section “4. Electrical Characteristics” on page 40 for the difference in output drive strength between the two modes.
222
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 21.8. P0: Port0
Bit
7
6
5
4
Name
P0[7:0]
Type
R/W
Reset
1
1
1
1
3
2
1
0
1
1
1
1
SFR Page = All Pages; SFR Address = 0x80; Bit-Addressable
Bit
Name
Description
Write
7:0
P0[7:0]
Read
0: Set output latch to logic
LOW.
Sets the Port latch logic
value or reads the Port pin 1: Set output latch to logic
logic state in Port cells con- HIGH.
figured for digital I/O.
Port 0 Data.
0: P0.n Port pin is logic
LOW.
1: P0.n Port pin is logic
HIGH.
SFR Definition 21.9. P0SKIP: Port0 Skip
Bit
7
6
5
4
3
Name
P0SKIP[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page= 0x0; SFR Address = 0xD4
Bit
Name
7:0
0
2
1
0
0
0
0
Function
P0SKIP[7:0] Port 0 Crossbar Skip Enable Bits.
These bits select Port 0 pins to be skipped by the Crossbar Decoder. Port pins used
for analog, special functions or GPIO should be skipped by the Crossbar.
0: Corresponding P0.n pin is not skipped by the Crossbar.
1: Corresponding P0.n pin is skipped by the Crossbar.
Rev. 1.3
223
Si1000/1/2/3/4/5
SFR Definition 21.10. P0MDIN: Port0 Input Mode
Bit
7
6
5
4
3
Name
P0MDIN[7:0]
Type
R/W
Reset
1
1
1
1
1
SFR Page= 0x0; SFR Address = 0xF1
Bit
Name
7:0
P0MDIN[7:0]
2
1
0
1
1
1
Function
Analog Configuration Bits for P0.7–P0.0 (respectively).
Port pins configured for analog mode have their weak pullup, and digital receiver
disabled. The digital driver is not explicitly disabled.
0: Corresponding P0.n pin is configured for analog mode.
1: Corresponding P0.n pin is not configured for analog mode.
SFR Definition 21.11. P0MDOUT: Port0 Output Mode
Bit
7
6
5
4
3
Name
P0MDOUT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xA4
Bit
Name
7:0
0
2
1
0
0
0
0
Function
P0MDOUT[7:0] Output Configuration Bits for P0.7–P0.0 (respectively).
These bits control the digital driver even when the corresponding bit in register
P0MDIN is logic 0.
0: Corresponding P0.n Output is open-drain.
1: Corresponding P0.n Output is push-pull.
224
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 21.12. P0DRV: Port0 Drive Strength
Bit
7
6
5
4
3
Name
P0DRV[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0xF; SFR Address = 0xA4
Bit
Name
7:0
0
2
1
0
0
0
0
Function
P0DRV[7:0] Drive Strength Configuration Bits for P0.7–P0.0 (respectively).
Configures digital I/O Port cells to high or low output drive strength.
0: Corresponding P0.n Output has low output drive strength.
1: Corresponding P0.n Output has high output drive strength.
Rev. 1.3
225
Si1000/1/2/3/4/5
SFR Definition 21.13. P1: Port1
Bit
7
6
5
4
Name
P1[7:0]
Type
R/W
Reset
1
1
1
1
3
2
1
0
1
1
1
1
SFR Page = All Pages; SFR Address = 0x90; Bit-Addressable
Bit
Name
Description
Write
7:0
P1[7:0]
Read
0: Set output latch to logic
LOW.
Sets the Port latch logic
value or reads the Port pin 1: Set output latch to logic
logic state in Port cells con- HIGH.
figured for digital I/O.
Port 1 Data.
0: P1.n Port pin is logic
LOW.
1: P1.n Port pin is logic
HIGH.
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the EZRadioPRO peripheral. P1.3 is not externally or
internally connected.
SFR Definition 21.14. P1SKIP: Port1 Skip
Bit
7
6
5
4
3
Name
P1SKIP[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xD5
Bit
Name
7:0
0
2
1
0
0
0
0
Function
P1SKIP[7:0] Port 1 Crossbar Skip Enable Bits.
These bits select Port 1 pins to be skipped by the Crossbar Decoder. Port pins used
for analog, special functions or GPIO should be skipped by the Crossbar.
0: Corresponding P1.n pin is not skipped by the Crossbar.
1: Corresponding P1.n pin is skipped by the Crossbar.
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the EZRadioPRO peripheral. P1.3 is not externally or
internally connected. P1.3 and P1.4 should always be skipped in the crossbar.
226
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 21.15. P1MDIN: Port1 Input Mode
Bit
7
6
5
4
3
Name
P1MDIN[7:0]
Type
R/W
Reset
1
1
1
1
1
SFR Page = 0x0; SFR Address = 0xF2
Bit
Name
7:0
P1MDIN[7:0]
2
1
0
1
1
1
Function
Analog Configuration Bits for P1.7–P1.0 (respectively).
Port pins configured for analog mode have their weak pullup and digital receiver
disabled. The digital driver is not explicitly disabled.
0: Corresponding P1.n pin is configured for analog mode.
1: Corresponding P1.n pin is not configured for analog mode.
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the EZRadioPRO peripheral. P1.3 is not externally or
internally connected.
SFR Definition 21.16. P1MDOUT: Port1 Output Mode
Bit
7
6
5
4
3
Name
P1MDOUT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xA5
Bit
Name
7:0
0
2
1
0
0
0
0
Function
P1MDOUT[7:0] Output Configuration Bits for P1.7–P1.0 (respectively).
These bits control the digital driver even when the corresponding bit in register
P1MDIN is logic 0.
0: Corresponding P1.n Output is open-drain.
1: Corresponding P1.n Output is push-pull.
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the EZRadioPRO peripheral. P1.3 is not externally or
internally connected.
Rev. 1.3
227
Si1000/1/2/3/4/5
SFR Definition 21.17. P1DRV: Port1 Drive Strength
Bit
7
6
5
4
3
Name
P1DRV[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0xF; SFR Address = 0xA5
Bit
Name
7:0
2
1
0
0
0
0
Function
P1DRV[7:0] Drive Strength Configuration Bits for P1.7–P1.0 (respectively).
Configures digital I/O Port cells to high or low output drive strength.
0: Corresponding P1.n Output has low output drive strength.
1: Corresponding P1.n Output has high output drive strength.
Note: P1.0, P1.1, P1.2, and P1.4 are internally connected to the EZRadioPRO peripheral. P1.3 is not externally or
internally connected.
SFR Definition 21.18. P2: Port2
Bit
7
6
5
4
Name
P2[7:0]
Type
R/W
Reset
1
1
1
1
3
2
1
0
1
1
1
1
SFR Page = All Pages; SFR Address = 0xA0; Bit-Addressable
Bit
Name
7:0
P2[7:0]
228
Description
Read
0: Set output latch to logic
LOW.
Sets the Port latch logic
value or reads the Port pin 1: Set output latch to logic
logic state in Port cells con- HIGH.
figured for digital I/O.
Port 2 Data.
Rev. 1.3
Write
0: P2.n Port pin is logic
LOW.
1: P2.n Port pin is logic
HIGH.
Si1000/1/2/3/4/5
SFR Definition 21.19. P2SKIP: Port2 Skip
Bit
7
6
5
4
3
Name
P2SKIP[7:0]
Type
R/W
Reset
0
0
0
0
0
2
1
0
0
0
0
SFR Page = 0x0; SFR Address = 0xD6
Bit
Name
7:0
P2SKIP[7:0]
Description
Read
Write
Port 1 Crossbar Skip Enable Bits.
These bits select Port 2 pins to be skipped by the Crossbar Decoder. Port pins
used for analog, special functions or GPIO should be skipped by the Crossbar.
0: Corresponding P2.n pin is not skipped by the Crossbar.
1: Corresponding P2.n pin is skipped by the Crossbar.
SFR Definition 21.20. P2MDIN: Port2 Input Mode
Bit
7
Name
Reserved
6
5
4
1
0
1
1
1
R/W
1
1
1
1
SFR Page = 0x0; SFR Address = 0xF3
Bit
Name
7
6:0
2
P2MDIN[6:0]
Type
Reset
3
1
Function
Reserved. Read = 1b; Must Write 1b.
P2MDIN[3:0]
Analog Configuration Bits for P2.6–P2.0 (respectively).
Port pins configured for analog mode have their weak pullup and digital receiver
disabled. The digital driver is not explicitly disabled.
0: Corresponding P2.n pin is configured for analog mode.
1: Corresponding P2.n pin is not configured for analog mode.
Rev. 1.3
229
Si1000/1/2/3/4/5
SFR Definition 21.21. P2MDOUT: Port2 Output Mode
Bit
7
6
5
4
3
Name
P2MDOUT[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xA6
Bit
Name
7:0
2
1
0
0
0
0
Function
P2MDOUT[7:0] Output Configuration Bits for P2.7–P2.0 (respectively).
These bits control the digital driver even when the corresponding bit in register
P2MDIN is logic 0.
0: Corresponding P2.n Output is open-drain.
1: Corresponding P2.n Output is push-pull.
SFR Definition 21.22. P2DRV: Port2 Drive Strength
Bit
7
6
5
4
3
Name
P2DRV[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0F; SFR Address = 0xA6
Bit
Name
7:0
P2DRV[7:0]
0
2
1
0
0
0
0
Function
Drive Strength Configuration Bits for P2.7–P2.0 (respectively).
Configures digital I/O Port cells to high or low output drive strength.
0: Corresponding P2.n Output has low output drive strength.
1: Corresponding P2.n Output has high output drive strength.
230
Rev. 1.3
Si1000/1/2/3/4/5
22. EZRadioPRO® Serial Interface (SPI1)
The EZRadioPRO serial interface (SPI1) provides access to the EZRadioPRO peripheral registers from
software executing on the MCU core. The serial interface consists of two SPI peripherals—a dedicated SPI
Master accessible from the MCU core and dedicated SPI Slave residing inside the EZRadioPRO peripheral. The SPI1 peripheral on the MCU core side can only be used in master mode to communicate with the
EZRadioPRO slave device in three wire mode. NSS for the EZRadioPRO is provided using Port 1.4, which
is internally routed to the EZRadioPRO peripheral. The EZRadioPRO Serial Interface provides a system
interrupt to regulate SPI traffic between the MCU core and the EZRadioPRO peripheral. This interrupt is
internally routed to the MCU core. The EZRadioPRO peripheral also has an nIRQ pin which should be
routed external to the package back into an external interrupt pin. The nIRQ interrupt pin is independent of
the EZRadioPRO Serial Interface.
SFR Bus
SYSCLK
SPI1CN
SPIF1
WCOL1
MODFn
RXOVRN1
NSS1MD1
NSS1MD0
TXBMT1
SPI1EN
SPI1CFG
SPIBSY
MSTEN
CKPHA
CKPOL
SLVSEL
NSSIN
SRMT
RXBMT
SCR7
SCR6
SCR5
SCR4
SCR3
SCR2
SCR1
SCR0
SPI1CKR
Clock Divide
Logic
SPI CONTROL LOGIC
Data Path
Control
EZRadioPRO Serial Interface (SPI1) IRQ
Pin Interface
Control
SCK
Tx Data
SPI1DAT
MISO
Transmit Data Buffer
Shift Register
7 6 5 4 3 2 1 0
Receive Data Buffer
Rx Data
Pin
Control
Logic
MOSI
NSS
C
R
O
S
S
B
A
R
P1.0
P1.1
SCK
MISO
P1.2
MOSI
P1.4
NSS
EZRadioPRO
Peripheral
Read
SPI0DAT
Write
SPI0DAT
SFR Bus
Figure 22.1. EZRadioPRO Serial Interface Block Diagram
Rev. 1.3
231
Si1000/1/2/3/4/5
22.1. Signal Descriptions
The four signals used by SPI1 (MOSI, MISO, SCK, NSS) are described below.
22.1.1. Master Out, Slave In (MOSI)
The master-out, slave-in (MOSI) signal is an output from a master device and an input to slave devices. It
is used to serially transfer data from the master to the slave. This signal is an output from the MCU core
and an input to the EZRadioPRO peripheral. Data is transferred most-significant bit first. MOSI is driven by
the MSB of the shift register.
22.1.2. Master In, Slave Out (MISO)
The master-in, slave-out (MISO) signal is an output from a slave device and an input to master devices. It
is used to serially transfer data from the EZRadioPRO to the MCU core. This signal is an input to the MCU
core and an output from the EZRadioPRO peripheral. Data is transferred most-significant bit first. The
MISO pin is placed in a high-impedance state when the SPI module is disabled.
22.1.3. Serial Clock (SCK)
The serial clock (SCK) signal is an output from the master device and an input to slave devices. It is used
to synchronize the transfer of data between the master and slave on the MOSI and MISO lines. SPI1 generates this signal.
22.1.4. Slave Select (NSS)
Since SPI1 operates in three wire mode, the NSS functionality built into the SPI state machine is not used.
Instead, a Port pin must be configured to control the chip select on the EZRadioPRO peripheral.
22.2. SPI Master Operation on the MCU Core Side
A SPI master device initiates all data transfers on a SPI bus. SPI1 is placed in master mode by setting the
Master Enable flag (MSTENn, SPI1CN.6). Writing a byte of data to the SPI1 data register (SPI1DAT) when
in master mode writes to the transmit buffer. If the SPI shift register is empty, the byte in the transmit buffer
is moved to the shift register, and a data transfer begins. The SPI1 master immediately shifts out the data
serially on the MOSI line while providing the serial clock on SCK. The SPIF1 (SPI1CN.7) flag is set to logic
1 at the end of the transfer. If interrupts are enabled, an interrupt request is generated when the SPIF flag
is set. While the SPI1 master transfers data to a slave on the MOSI line, the addressed SPI slave device
simultaneously transfers the contents of its shift register to the SPI master on the MISO line in a full-duplex
operation. Therefore, the SPIF flag serves as both a transmit-complete and receive-data-ready flag. The
data byte received from the slave is transferred MSB-first into the master's shift register. When a byte is
fully shifted into the register, it is moved to the receive buffer where it can be read by the processor by
reading SPI1DAT.
22.3. SPI Slave Operation on the EZRadioPRO Peripheral Side
The EZRadioPRO peripheral presents a standard 4-wire SPI interface: SCK, MISO, MOSI and NSS. The
SPI master can read data from the device on the MOSI output pin. A SPI transaction is a 16-bit sequence
which consists of a Read-Write (R/W) select bit, followed by a 7-bit address field (ADDR), and an 8-bit data
field (DATA) as demonstrated in Figure 22.2. The 7-bit address field is used to select one of the 128, 8-bit
control registers. The R/W select bit determines whether the SPI transaction is a read or write transaction.
If R/W = 1 it signifies a WRITE transaction, while R/W = 0 signifies a READ transaction. The contents
(ADDR or DATA) are latched into the transceiver every eight clock cycles. The timing parameters for the
SPI interface are shown in Table 22.1. The SCK rate is flexible with a maximum rate of 10 MHz.
232
Rev. 1.3
Si1000/1/2/3/4/5
Data
Address
MSB
MSB
LSB
RW A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 xx xx RW A7
MOSI
SDI
SCLK
NSS
nSEL
Figure 22.2. SPI Timing
Table 22.1. Serial Interface Timing Parameters
Symbol
Parameter
Min
(nsec)
tCH
Clock high time
40
tCL
Clock low time
40
tDS
Data setup time
20
tDH
Data hold time
20
tDD
Output data delay
time
20
tEN
Output enable time
20
tDE
Output disable time
50
tSS
Select setup time
20
tSH
Select hold time
50
tSW
Select high period
80
Diagram
SCL
SCLK
tSS
tCL
tCH
tDS tDH
tDD
tSH
tDE
MOSI
SDI
SDO
MISO
tEN
tSW
nSEL
NSS
To read back data from the transceiver, the R/W bit must be set to 0 followed by the 7-bit address of the
register from which to read. The 8 bit DATA field following the 7-bit ADDR field is ignored on the MOSI pin
when R/W = 0. The next eight negative edge transitions of the SCK signal will clock out the contents of the
selected register. The data read from the selected register will be available on the MISO output. The READ
function is shown in Figure 22.3. After the READ function is completed the MISO signal will remain at
either a logic 1 or logic 0 state depending on the last data bit clocked out (D0). When NSS goes high the
MISO output pin will be pulled high by internal pullup.
First Bit
SDI
MOSI
RW
=0
Last Bit
A6 A5 A4 A3 A2 A1 A0
D7
=X
D6
=X
D5
=X
D4
=X
D3
=X
D2
=X
D1
=X
D0
=X
SCLK
SCL
First Bit
SDO
MISO
D7 D6 D5 D4 D3
Last Bit
D2 D1 D0
NSS
nSEL
Figure 22.3. SPI Timing—READ Mode
Rev. 1.3
233
Si1000/1/2/3/4/5
The SPI interface contains a burst read/write mode which allows for reading/writing sequential registers
without having to re-send the SPI address. When the NSS bit is held low while continuing to send SCK
pulses, the SPI interface will automatically increment the ADDR and read from/write to the next address.
An example burst write transaction is illustrated in Figure 22.4 and a burst read in Figure 22.5. As long as
NSS is held low, input data will be latched into the transceiver every eight SCK cycles.
First Bit
MOSI
SDI
RW
=1
Last Bit
A6 A5 A4 A3 A2 A1 A0
D7
=X
D6
=X
D5
=X
D4
=X
D3
=X
D2
=X
D1
=X
D0
=X
D7
=X
D6
=X
D5
=X
D4
=X
D3
=X
D2
=X
D1
=X
D0
=X
SCLK
SCL
nSEL
NSS
Figure 22.4. SPI Timing—Burst Write Mode
First Bit
SDI
MOSI
RW
=0
Last Bit
A6 A5 A4 A3 A2 A1 A0
D7
=X
D6
=X
D5
=X
D4
=X
D3
=X
D2
=X
D1
=X
D0
=X
SCLK
SCL
First Bit
SDO
MISO
D7 D6 D5 D4 D3
D2 D1 D0 D7 D6 D5 D4 D3
NSS
nSEL
Figure 22.5. SPI Timing—Burst Read Mode
234
Rev. 1.3
D2 D1 D0
Si1000/1/2/3/4/5
22.4. EZRadioPRO Serial Interface Interrupt Sources
When SPI1 interrupts are enabled, the following flags will generate an interrupt when they are set to logic
1:
All of the following bits must be cleared by software.
1. The SPI Interrupt Flag, SPIFn (SPInCN.7) is set to logic 1 at the end of each byte transfer.
This flag can occur in all SPIn modes.
2. The Write Collision Flag, WCOLn (SPInCN.6) is set to logic 1 if a write to SPInDAT is
attempted when the transmit buffer has not been emptied to the SPI shift register. When this
occurs, the write to SPInDAT will be ignored, and the transmit buffer will not be written.This
flag can occur in all SPIn modes.
3. The Mode Fault Flag MODFn (SPInCN.5) is set to logic 1 when SPIn is configured as a
master, and for multi-master mode and the NSS pin is pulled low. When a Mode Fault occurs,
the MSTENn and SPIENn bits in SPI0CN are set to logic 0 to disable SPIn and allow another
master device to access the bus.
4. The Receive Overrun Flag RXOVRNn (SPInCN.4) is set to logic 1 when configured as a slave,
and a transfer is completed and the receive buffer still holds an unread byte from a previous
transfer. The new byte is not transferred to the receive buffer, allowing the previously received
data byte to be read. The data byte which caused the overrun is lost.
22.5. Serial Clock Phase and Polarity
Four combinations of serial clock phase and polarity can be selected using the clock control bits in the SPI
Configuration Register (SPI1CFG). The CKPHA bit (SPI1CFG.5) selects one of two clock phases (edge
used to latch the data). The CKPOL bit (SPI1CFG.4) selects between an active-high or active-low clock.
Both CKPOL and CKPHA must be set to zero in order to communicate with the EZRadioPRO peripheral.
The SPI1 Clock Rate Register (SPI1CKR) as shown in SFR Definition 22.3 controls the master mode
serial clock frequency. When the SPI is configured as a master, the maximum data transfer rate (bits/sec)
is one-half the system clock frequency or 12.5 MHz, whichever is slower.
SCK
(CKPOL=0, CKPHA=0)
SCK
(CKPOL=0, CKPHA=1)
SCK
(CKPOL=1, CKPHA=0)
SCK
(CKPOL=1, CKPHA=1)
MISO/MOSI
MSB
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
NSS (Must Remain High
in Multi-Master Mode)
Figure 22.6. Master Mode Data/Clock Timing
Rev. 1.3
235
Si1000/1/2/3/4/5
22.6. SPI Special Function Registers
SPI1 is accessed and controlled through four special function registers in the system controller: SPI1CN
Control Register, SPI1DAT Data Register, SPI1CFG Configuration Register, and SPI1CKR Clock Rate
Register. The special function registers related to the operation of the SPI1 Bus are described in the following figures.
236
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 22.1. SPI1CFG: SPI Configuration
Bit
7
6
5
4
3
2
1
0
Name
SPIBSY
MSTEN
CKPHA
CKPOL
Type
R
R/W
R/W
R/W
R
R
R
R
Reset
0
0
0
0
0
1
1
1
SFR Page = 0x0; SFR Address = 0x84
Bit
Name
7
SPIBSY
Function
SPI Busy.
This bit is set to logic 1 when a SPI transfer is in progress.
6
MSTEN
Master Mode Enable.
When set to ‘1’, enables master mode. This bit must be set to 1 to communicate
with the EZRadioPRO peripheral.
5
CKPHA
SPI Clock Phase.
0: Data centered on first edge of SCK period.*
1: Data centered on second edge of SCK period.*
4
CKPOL
SPI Clock Polarity.
0: SCK line low in idle state.
1: SCK line high in idle state.
3:0
Reserved.
Read = 0000, Write = don’t care.
Note: In master mode, data on MISO is sampled one SYSCLK before the end of each data bit, to provide maximum
settling time for the slave device. See Table 22.2 for timing parameters.
Rev. 1.3
237
Si1000/1/2/3/4/5
SFR Definition 22.2. SPI1CN: SPI Control
Bit
7
6
5
Name
SPIF1
Type
R/W
R/W
R/W
Reset
0
0
0
4
3
2
1
0
NSS1MD1
NSS1MD0
TXBMT1
SPI1EN
R/W
R/W
R/W
R
R/W
0
0
1
1
0
WCOL1 MODF1
SFR Page = 0x0; SFR Address = 0xB0; Bit-Addressable
Bit
Name
7
SPIF1
Function
SPI1 Interrupt Flag.
This bit is set to logic 1 by hardware at the end of a data transfer. If interrupts are
enabled, setting this bit causes the CPU to vector to the SPI1 interrupt service
routine. This bit is not automatically cleared by hardware. It must be cleared by
software.
6
WCOL1
Write Collision Flag.
This bit is set to logic 1 by hardware (and generates a SPI1 interrupt) to indicate a
write to the SPI1 data register was attempted while a data transfer was in progress.
It must be cleared by software.
5
MODF1
Mode Fault Flag.
This bit is set to logic 1 by hardware (and generates a SPI1 interrupt) when a master mode collision is detected (NSS is low, MSTEN = 1, and NSSMD[1:0] = 01).
This bit is not automatically cleared by hardware. It must be cleared by software.
4
3:2
Reserved.
Read = varies; Write = must write zero.
NSS1MD[1:0] Slave Select Mode.
Must be set to 00b. SPI1 can only be used in 3-wire master mode.
1
TXBMT1
Transmit Buffer Empty.
This bit will be set to logic 0 when new data has been written to the transmit buffer.
When data in the transmit buffer is transferred to the SPI shift register, this bit will
be set to logic 1, indicating that it is safe to write a new byte to the transmit buffer.
0
SPI1EN
SPI1 Enable.
0: SPI1 disabled.
1: SPI1 enabled.
238
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 22.3. SPI1CKR: SPI Clock Rate
Bit
7
6
5
4
3
Name
SCR1[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0x85
Bit
Name
7:0
SCR1
0
2
1
0
0
0
0
Function
SPI Clock Rate.
These bits determine the frequency of the SCK output when the SPI module is
configured for master mode operation. The SCK clock frequency is a divided
version of the system clock, and is given in the following equation, where SYSCLK
is the system clock frequency and SPI1CKR is the 8-bit value held in the SPI1CKR
register.
SYSCLK
f SCK = ----------------------------------------------------------2   SPI1CKR[7:0] + 1 
for 0 <= SPI0CKR <= 255
Example: If SYSCLK = 2 MHz and SPI1CKR = 0x04,
2000000
f SCK = -------------------------2  4 + 1
f SCK = 200 kHz
Rev. 1.3
239
Si1000/1/2/3/4/5
SFR Definition 22.4. SPI1DAT: SPI Data
Bit
7
6
5
4
3
Name
SPI1DAT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0x86
Bit
Name
7:0
SPI1DAT
0
2
1
0
0
0
0
Function
SPI1 Transmit and Receive Data.
The SPI1DAT register is used to transmit and receive SPI1 data. Writing data to
SPI1DAT places the data into the transmit buffer and initiates a transfer when in
Master Mode. A read of SPI1DAT returns the contents of the receive buffer.
240
Rev. 1.3
Si1000/1/2/3/4/5
SCK*
T
MCKH
T
MCKL
T
T
MIS
MIH
MISO
MOSI
* SCK is shown for CKPOL = 0. SCK is the opposite polarity for CKPOL = 1.
Figure 22.7. SPI Master Timing
Table 22.2. SPI Timing Parameters
Parameter
Description
Min
Max
Units
Master Mode Timing
TMCKH
SCK High Time
1 x TSYSCLK
—
ns
TMCKL
SCK Low Time
1 x TSYSCLK
—
ns
TMIS
MISO Valid to SCK Shift Edge
1 x TSYSCLK + 20
—
ns
TMIH
SCK Shift Edge to MISO Change
0
—
ns
Note: TSYSCLK is equal to one period of the device system clock (SYSCLK).
Rev. 1.3
241
Si1000/1/2/3/4/5
23. EZRadioPRO® 240–960 MHz Transceiver
Si1000/1/2/3/4/5 devices include the EZRadioPRO family of ISM wireless transceivers with continuous frequency tuning over 240–960 MHz. The wide operating voltage range of 1.8–3.6 V and low current consumption makes the EZRadioPRO an ideal solution for battery powered applications.
The EZRadioPRO transceiver operates as a time division duplexing (TDD) transceiver where the device
alternately transmits and receives data packets. The device uses a single-conversion mixer to downconvert the 2-level FSK/GFSK/OOK modulated receive signal to a low IF frequency. Following a programmable gain amplifier (PGA) the signal is converted to the digital domain by a high performance  ADC
allowing filtering, demodulation, slicing, and packet handling to be performed in the built-in DSP increasing
the receiver’s performance and flexibility versus analog based architectures. The demodulated signal is
then output to the system MCU through a programmable GPIO or via the standard SPI bus by reading the
64-byte RX FIFO.
A single high precision local oscillator (LO) is used for both transmit and receive modes since the transmitter and receiver do not operate at the same time. The LO is generated by an integrated VCO and  Fractional-N PLL synthesizer. The synthesizer is designed to support configurable data rates, output frequency
and frequency deviation at any frequency between 240–960 MHz. The transmit FSK data is modulated
directly into the  data stream and can be shaped by a Gaussian low-pass filter to reduce unwanted
spectral content.
The Si1000’s PA output power can be configured between –1 and +20 dBm in 3 dB steps, while the
Si1002/3/4/5's PA output power can be configured between –8 and +13 dBm in 3 dB steps. The PA is single-ended to allow for easy antenna matching and low BOM cost. The PA incorporates automatic ramp-up
and rampdown control to reduce unwanted spectral spreading. The +20 dBm power amplifier of the
Si1000/1 can also be used to compensate for the reduced performance of a lower cost, lower performance
antenna or antenna with size constraints due to a small form-factor. Competing solutions require large and
expensive external PAs to achieve comparable performance. The EZRadioPRO transceivers support frequency hopping, TX/RX switch control, and antenna diversity switch control to extend the link range and
improve performance.
The EZRadioPRO peripheral also controls three GPIO pins: GPIO_0, GPIO_1, and GPIO_2. See Application Note “AN415: EZRadioPRO Programming Guide“ for details on initializing and using the EZRadioPRO
peripheral.
242
Rev. 1.3
Si1000/1/2/3/4/5
23.1. EZRadioPRO Operating Modes
The EZRadioPRO transceivers provide several operating modes which can be used to optimize the power
consumption for a given application. Depending upon the system communication protocol, an optimal
trade-off between the radio wake time and power consumption can be achieved.
Table 23.1 summarizes the operating modes of the EZRadioPRO transceivers. In general, any given operating mode may be classified as an active mode or a power saving mode. The table indicates which
block(s) are enabled (active) in each corresponding mode. With the exception of the SHUTDOWN mode,
all can be dynamically selected by sending the appropriate commands over the SPI. An “X” in any cell
means that, in the given mode of operation, that block can be independently programmed to be either ON
or OFF, without noticeably impacting the current consumption. The SPI circuit block includes the SPI interface hardware and the device register space. The 32 kHz OSC block includes the 32.768 kHz RC oscillator or 32.768 kHz crystal oscillator and wake-up timer. AUX (Auxiliary Blocks) includes the temperature
sensor, general purpose ADC, and low-battery detector.
Table 23.1. EZRadioPRO Operating Modes
Mode
Name
Circuit Blocks
Digital LDO
SPI
30 MHz
XTAL
PLL
PA
RX
IVDD
OFF (Register contents
lost)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
15 nA
STANDBY ON (Register
contents
SLEEP
retained)
SENSOR
ON
OFF
OFF
OFF
OFF
OFF
OFF
450 nA
ON
ON
X
OFF
OFF
OFF
OFF
1 µA
ON
X
ON
OFF
OFF
OFF
OFF
1 µA
READY
ON
X
X
ON
OFF
OFF
OFF
600 µA
TUNING
ON
X
X
ON
ON
OFF
OFF
8.5 mA
TRANSMIT
ON
X
X
ON
ON
ON
OFF
30 mA*
RECEIVE
ON
X
X
ON
ON
OFF
ON
18.5 mA
SHUTDOWN
32 kHz OSC AUX
Note: Using Si1002/3 at +13 dBm using recommended reference design. These power modes are for the
EZRadioPRO peripheral only and are independent of the MCU power modes.
Rev. 1.3
243
Si1000/1/2/3/4/5
23.1.1. Operating Mode Control
There are four primary states in the EZRadioPRO transceiver radio state machine: SHUTDOWN, IDLE,
TX, and RX (see Figure 23.1). The SHUTDOWN state completely shuts down the radio to minimize current
consumption. There are five different configurations/options for the IDLE state which can be selected to
optimize the chip to the applications needs. "Register 07h. Operating Mode and Function Control 1" controls which operating mode/state is selected with the exception of SHUTDOWN which is controlled by SDN
pin 20. The TX and RX state may be reached automatically from any of the IDLE states by setting the
txon/rxon bits in "Register 07h. Operating Mode and Function Control 1". Table 23.2 shows each of the
operating modes with the time required to reach either RX or TX mode as well as the current consumption
of each mode.
The transceivers include a low-power digital regulated supply (LPLDO) which is internally connected in
parallel to the output of the main digital regulator (and is available externally at the VR_DIG pin). This common digital supply voltage is connected to all digital circuit blocks including the digital modem, crystal oscillator, SPI, and register space. The LPLDO has extremely low quiescent current consumption but limited
current supply capability; it is used only in the IDLE-STANDBY and IDLE-SLEEP modes. The main digital
regulator is automatically enabled in all other modes.
SHUTDOWN
SHUT
DWN
IDLE*
TX
RX
*Five Different Options for IDLE
Figure 23.1. State Machine Diagram
Table 23.2. EZRadioPRO Operating Modes Response Time
State/Mode
244
Response Time to
Current in State /Mode
[µA]
TX
RX
Shut Down State
16.8 ms
16.8 ms
15 nA
Idle States:
Standby Mode
Sleep Mode
Sensor Mode
Ready Mode
Tune Mode
800 µs
800 µs
800 µs
200 µs
200 µs
800 µs
800 µs
800 µs
200 µs
200 µs
450 nA
1 µA
1 µA
800 µA
8.5 mA
TX State
NA
200 µs
30 mA @ +13 dBm
RX State
200 µs
NA
18.5 mA
Rev. 1.3
Si1000/1/2/3/4/5
23.1.1.1. SHUTDOWN State
The SHUTDOWN state is the lowest current consumption state of the device with nominally less than
15 nA of current consumption. The shutdown state may be entered by driving the SDN pin (Pin 20) high.
The SDN pin should be held low in all states except the SHUTDOWN state. In the SHUTDOWN state, the
contents of the registers are lost and there is no SPI access.
When the chip is connected to the power supply, a POR will be initiated after the falling edge of SDN. After
a POR, the device will be in READY mode with the buffers enabled.
23.1.1.1.1. IDLE State
There are five different modes in the IDLE state which may be selected by "Register 07h. Operating Mode
and Function Control 1". All modes have a tradeoff between current consumption and response time to
TX/RX mode. This tradeoff is shown in Table 23.2. After the POR event, SWRESET, or exiting from the
SHUTDOWN state the chip will default to the IDLE-READY mode. After a POR event the interrupt registers
must be read to properly enter the SLEEP, SENSOR, or STANDBY mode and to control the 32 kHz clock
correctly.
23.1.1.1.2. STANDBY Mode
STANDBY mode has the lowest current consumption of the five IDLE states with only the LPLDO enabled
to maintain the register values. In this mode the registers can be accessed in both read and write mode.
The STANDBY mode can be entered by writing 0h to "Register 07h. Operating Mode and Function Control
1". If an interrupt has occurred (i.e., the nIRQ pin = 0) the interrupt registers must be read to achieve the
minimum current consumption. Additionally, the ADC should not be selected as an input to the GPIO in this
mode as it will cause excess current consumption.
23.1.1.1.3. SLEEP Mode
In SLEEP mode the LPLDO is enabled along with the Wake-Up-Timer, which can be used to accurately
wake-up the radio at specified intervals. See “Wake-Up Timer and 32 kHz Clock Source” on page 278 for
more information on the Wake-Up-Timer. SLEEP mode is entered by setting enwt = 1 (40h) in "Register
07h. Operating Mode and Function Control 1". If an interrupt has occurred (i.e., the nIRQ pin = 0) the interrupt registers must be read to achieve the minimum current consumption. Also, the ADC should not be
selected as an input to the GPIO in this mode as it will cause excess current consumption.
23.1.1.1.4. SENSOR Mode
In SENSOR mode either the Low Battery Detector, Temperature Sensor, or both may be enabled in addition to the LPLDO and Wake-Up-Timer. The Low Battery Detector can be enabled by setting enlbd = 1 in
"Register 07h. Operating Mode and Function Control 1". See “Temperature Sensor” on page 275 and “Low
Battery Detector” on page 277 for more information on these features. If an interrupt has occurred (i.e.,
the nIRQ pin = 0) the interrupt registers must be read to achieve the minimum current consumption.
23.1.1.1.5. READY Mode
READY Mode is designed to give a fast transition time to TX mode with reasonable current consumption.
In this mode the Crystal oscillator remains enabled reducing the time required to switch to TX or RX mode
by eliminating the crystal start-up time. READY mode is entered by setting xton = 1 in "Register 07h. Operating Mode and Function Control 1". To achieve the lowest current consumption state the crystal oscillator
buffer should be disabled in “Register 62h. Crystal Oscillator Control and Test.” To exit READY mode,
bufovr (bit 1) of this register must be set back to 0.
23.1.1.1.6. TUNE Mode
In TUNE mode the PLL remains enabled in addition to the other blocks enabled in the IDLE modes. This
will give the fastest response to TX mode as the PLL will remain locked but it results in the highest current
consumption. This mode of operation is designed for frequency hopping spread spectrum systems
(FHSS). TUNE mode is entered by setting pllon = 1 in "Register 07h. Operating Mode and Function Control 1". It is not necessary to set xton to 1 for this mode, the internal state machine automatically enables
the crystal oscillator.
Rev. 1.3
245
Si1000/1/2/3/4/5
23.1.1.2. TX State
The TX state may be entered from any of the IDLE modes when the txon bit is set to 1 in "Register 07h.
Operating Mode and Function Control 1". A built-in sequencer takes care of all the actions required to transition between states from enabling the crystal oscillator to ramping up the PA. The following sequence of
events will occur automatically when going from STANDBY mode to TX mode by setting the txon bit.
1. Enable the main digital LDO and the Analog LDOs.
2. Start up crystal oscillator and wait until ready (controlled by an internal timer).
3. Enable PLL.
4. Calibrate VCO (this action is skipped when the skipvco bit is 1, default value is 0).
5. Wait until PLL settles to required transmit frequency (controlled by an internal timer).
6. Activate power amplifier and wait until power ramping is completed (controlled by an internal timer).
7. Transmit packet.
Steps in this sequence may be eliminated depending on which IDLE mode the chip is configured to prior to
setting the txon bit. By default, the VCO and PLL are calibrated every time the PLL is enabled.
23.1.1.3. RX State
The RX state may be entered from any of the IDLE modes when the rxon bit is set to 1 in "Register 07h.
Operating Mode and Function Control 1". A built-in sequencer takes care of all the actions required to transition from one of the IDLE modes to the RX state. The following sequence of events will occur automatically to get the chip into RX mode when going from STANDBY mode to RX mode by setting the rxon bit:
1. Enable the main digital LDO and the Analog LDOs.
2. Start up crystal oscillator and wait until ready (controlled by an internal timer).
3. Enable PLL.
4. Calibrate VCO (this action is skipped when the skipvco bit is 1, default value is 0).
5. Wait until PLL settles to required receive frequency (controlled by an internal timer).
6. Enable receive circuits: LNA, mixers, and ADC.
7. Enable receive mode in the digital modem.
Depending on the configuration of the radio all or some of the following functions will be performed automatically by the digital modem: AGC, AFC (optional), update status registers, bit synchronization, packet
handling (optional) including sync word, header check, and CRC.
23.1.1.4. Device Status
Add R/W
02
R
Function/
Description
D7
D6
D5
D4
D3
Device Status
ffovfl
ffunfl
rxffem
headerr
freqerr
D2
D1
D0
cps[1] cps[0]
POR Def.
—
The operational status of the EZRadioPRO peripheral can be read from "Register 02h. Device Status".
23.2. Interrupts
The EZRadioPRO peripheral is capable of generating an interrupt signal (nIRQ) when certain events
occur. The nIRQ pin is driven low to indicate a pending interrupt request. The EZRadioPRO interrupt
does not have an internal interrupt vector. To use the interrupt, the nIRQ pin must be looped back
to an external interrupt input. This interrupt signal will be generated when any one (or more) of the interrupt events (corresponding to the Interrupt Status bits) shown below occur. The nIRQ pin will remain low
until the Interrupt Status Register(s) (Registers 03h–04h) containing the active Interrupt Status bit is read.
The nIRQ output signal will then be reset until the next change in status is detected. The interrupts must be
246
Rev. 1.3
Si1000/1/2/3/4/5
enabled by the corresponding enable bit in the Interrupt Enable Registers (Registers 05h–06h). All
enabled interrupt bits will be cleared when the corresponding interrupt status register is read. If the interrupt is not enabled when the event occurs it will not trigger the nIRQ pin, but the status may still be read at
anytime in the Interrupt Status registers.
Add R/W
Function/
Description
D7
D6
D5
D4
D3
D2
D1
D0
POR
Def.
03
R
Interrupt Status 1
ifferr
itxffafull
itxffaem
irxffafull
iext
ipksent
ipkvalid
icrcerror
—
04
R
Interrupt Status 2
iswdet
ipreaval
ipreainval
irssi
iwut
ilbd
ichiprdy
ipor
—
05 R/W Interrupt Enable 1 enfferr entxffafull entxffaem enrxffafull enext enpksent enpkvalid encrcerror
00h
06 R/W Interrupt Enable 2 enswdet enpreava enpreainval
01h
enrssi
enwut
enlbd
enchiprdy
enpor
See “AN440: EZRadioPRO Detailed Register Descriptions” for a complete list of interrupts.
23.3. System Timing
The system timing for TX and RX modes is shown in Figures 23.2 and 23.3. The figures demonstrate transitioning from STANDBY mode to TX or RX mode through the built-in sequencer of required steps. The
user only needs to program the desired mode, and the internal sequencer will properly transition the part
from its current mode.
TX Packet
PA RAMP DOWN
PLLTS
PRE PA RAMP
PA RAMP UP
PLL CAL
XTAL Settling
Time
PLL T0
The VCO will automatically calibrate at every frequency change or power up. The PLL T0 time is to allow
for bias settling of the VCO. The PLL TS time is for the settling time of the PLL, which has a default setting
of 100 µs. The total time for PLL T0, PLL CAL, and PLL TS under all conditions is 200 µs. Under certain
applications, the PLL T0 time and the PLL CAL may be skipped for faster turn-around time. Contact applications support if faster turnaround time is desired.
Configurable 5-20us, Recommend 5us
Configurable 5-20us, Recommend 5us
6us, Fixed
Configurable 0-310us, Recommend 100us
50us, May be skipped
Configurable 0-70us, Default = 50us
600us
Figure 23.2. TX Timing
Rev. 1.3
247
PLLTS
PLL CAL
XTAL Settling
Time
PLL T0
Si1000/1/2/3/4/5
RX Packet
Configurable 0-310us, Recommend 100us
50us, May be skipped
Configurable 0-70us, Default =50us
600us
Figure 23.3. RX Timing
23.3.1. Frequency Control
For calculating the necessary frequency register settings it is recommended that customers use Silicon
Labs’ Wireless Design Suite (WDS) or the EZRadioPRO Register Calculator worksheet (in Microsoft
Excel) available on the product website. These methods offer a simple method to quickly determine the
correct settings based on the application requirements. The following information can be used to calculated these values manually.
23.3.2. Frequency Programming
In order to receive or transmit an RF signal, the desired channel frequency, fcarrier, must be programmed
into the transceiver. Note that this frequency is the center frequency of the desired channel and not an LO
frequency. The carrier frequency is generated by a Fractional-N Synthesizer, using 10 MHz both as the reference frequency and the clock of the (3rd order) ∆Σ modulator. This modulator uses modulo 64000 accumulators. This design was made to obtain the desired frequency resolution of the synthesizer. The overall
division ratio of the feedback loop consist of an integer part (N) and a fractional part (F).In a generic sense,
the output frequency of the synthesizer is as follows:
f OUT  10MHz  ( N  F )
The fractional part (F) is determined by three different values, Carrier Frequency (fc[15:0]), Frequency Offset (fo[8:0]), and Frequency Deviation (fd[7:0]). Due to the fine resolution and high loop bandwidth of the
synthesizer, FSK modulation is applied inside the loop and is done by varying F according to the incoming
data; this is discussed further in “Frequency Deviation” on page 251. Also, a fixed offset can be added to
fine-tune the carrier frequency and counteract crystal tolerance errors. For simplicity assume that only the
fc[15:0] register will determine the fractional component. The equation for selection of the carrier frequency
is shown below:
248
Rev. 1.3
Si1000/1/2/3/4/5
f carrier  10 MHz  (hbsel  1)  ( N  F )
fTX  10MHz * (hbsel  1) * ( fb[4 : 0]  24 
Add R/W
73
R/W
74
R/W
75
R/W
76
R/W
77
R/W
fc[15 : 0]
)
64000
Function/
Description
D7
D6
D5
D4
D3
D2
Frequency
Offset 1
Frequency
Offset 2
Frequency Band
Select
Nominal Carrier
Frequency 1
Nominal Carrier
Frequency 0
fo[7]
fo[6]
fo[5]
fo[4]
fo[3]
fo[2]
D1
D0
POR Def.
fo[1] fo[0]
00h
fo[9] fo[8]
00h
sbsel
hbsel
fb[4]
fb[3]
fb[2]
fb[1] fb[0]
35h
fc[15]
fc[14]
fc[13]
fc[12]
fc[11]
fc[10]
fc[9] fc[8]
BBh
fc[7]
fc[6]
fc[5]
fc[4]
fc[3]
fc[2]
fc[1] fc[0]
80h
The integer part (N) is determined by fb[4:0]. Additionally, the output frequency can be halved by connecting a ÷2 divider to the output. This divider is not inside the loop and is controlled by the hbsel bit in "Register 75h. Frequency Band Select". This effectively partitions the entire 240–960 MHz frequency range into
two separate bands: High Band (HB) for hbsel = 1, and Low Band (LB) for hbsel = 0. The valid range of
fb[4:0] is from 0 to 23. If a higher value is written into the register, it will default to a value of 23. The integer
part has a fixed offset of 24 added to it as shown in the formula above. Table 23.3 demonstrates the selection of fb[4:0] for the corresponding frequency band.
After selection of the fb (N) the fractional component may be solved with the following equation:


fTX
 fb[4 : 0]  24  * 64000
fc[15 : 0]  
 10MHz * (hbsel  1)

fb and fc are the actual numbers stored in the corresponding registers.
Table 23.3. Frequency Band Selection
fb[4:0] Value
N
Frequency Band
hbsel=0
hbsel=1
0
24
240–249.9 MHz
480–499.9 MHz
1
25
250–259.9 MHz
500–519.9 MHz
2
26
260–269.9 MHz
520–539.9 MHz
3
27
270–279.9 MHz
540–559.9 MHz
4
28
280–289.9 MHz
560–579.9 MHz
5
29
290–299.9 MHz
580–599.9 MHz
6
30
300–309.9 MHz
600–619.9 MHz
7
31
310–319.9 MHz
620–639.9 MHz
8
32
320–329.9 MHz
640–659.9 MHz
Rev. 1.3
249
Si1000/1/2/3/4/5
Table 23.3. Frequency Band Selection (Continued)
9
33
330–339.9 MHz
660–679.9 MHz
10
34
340–349.9 MHz
680–699.9 MHz
11
35
350–359.9 MHz
700–719.9 MHz
12
36
360–369.9 MHz
720–739.9 MHz
13
37
370–379.9 MHz
740–759.9 MHz
14
38
380–389.9 MHz
760–779.9 MHz
15
39
390–399.9 MHz
780–799.9 MHz
16
40
400–409.9 MHz
800–819.9 MHz
17
41
410–419.9 MHz
820–839.9 MHz
18
42
420–429.9 MHz
840–859.9 MHz
19
43
430–439.9 MHz
860–879.9 MHz
20
44
440–449.9 MHz
880–899.9 MHz
21
45
450–459.9 MHz
900–919.9 MHz
22
46
460–469.9 MHz
920–939.9 MHz
23
47
470–479.9 MHz
940–960 MHz
The chip will automatically shift the frequency of the Synthesizer down by 937.5 kHz (30 MHz ÷ 32) to
achieve the correct Intermediate Frequency (IF) when RX mode is entered. Low-side injection is used in
the RX Mixing architecture; therefore, no frequency reprogramming is required when using the same TX
frequency and switching between RX/TX modes. For operation in the frequency bands between 240–
320 MHz and 480–640 MHz with a temperature above 60 °C, register modifications are required. In these
cases, write 03h to register 59h and 02h to register 5Ah.
23.3.3. Easy Frequency Programming for FHSS
While Registers 73h–77h may be used to program the carrier frequency of the transceiver, it is often easier
to think in terms of “channels” or “channel numbers” rather than an absolute frequency value in Hz. Also,
there may be some timing-critical applications (such as for Frequency Hopping Systems) in which it is
desirable to change frequency by programming a single register. Once the channel step size is set, the frequency may be changed by a single register corresponding to the channel number. A nominal frequency is
first set using Registers 73h–77h, as described above. Registers 79h and 7Ah are then used to set a channel step size and channel number, relative to the nominal setting. The Frequency Hopping Step Size
(fhs[7:0]) is set in increments of 10 kHz with a maximum channel step size of 2.56 MHz. The Frequency
Hopping Channel Select Register then selects channels based on multiples of the step size.
Fcarrier  Fnom  fhs[7 : 0]  ( fhch[7 : 0]  10kHz )
For example: if the nominal frequency is set to 900 MHz using Registers 73h–77h and the channel step
size is set to 1 MHz using "Register 7Ah. Frequency Hopping Step Size". For example, if the "Register
79h. Frequency Hopping Channel Select" is set to 5d, the resulting carrier frequency would be 905 MHz.
Once the nominal frequency and channel step size are programmed in the registers, it is only necessary to
program the fhch[7:0] register in order to change the frequency.
250
Rev. 1.3
Si1000/1/2/3/4/5
Add R/W
Function/
Description
D7
D6
D5
D4
D3
D2
D1
D0
POR Def.
79
R/W
Frequency Hopping
Channel Select
fhch[7] fhch[6] fhch[5] fhch[4] fhch[3] fhch[2] fhch[1]
fhch[0]
00h
7A
R/W
Frequency Hopping
Step Size
fhs[7]
fhs[0]
00h
fhs[6]
fhs[5]
fhs[4]
fhs[3]
fhs[2]
fhs[1]
23.3.4. Automatic State Transition for Frequency Change
If registers 79h or 7Ah are changed in either TX or RX mode, the state machine will automatically transition
the chip back to TUNE, change the frequency, and automatically go back to either TX or RX. This feature
is useful to reduce the number of SPI commands required in a Frequency Hopping System. This in turn
reduces microcontroller activity, reducing current consumption. The exception to this is during TX FIFO
mode. If a frequency change is initiated during a TX packet, then the part will complete the current TX
packet and will only change the frequency for subsequent packets.
23.3.5. Frequency Deviation
The peak frequency deviation is configurable from ±0.625 to ±320 kHz. The Frequency Deviation (∆f) is
controlled by the Frequency Deviation Register (fd), address 71 and 72h, and is independent of the carrier
frequency setting. When enabled, regardless of the setting of the hbsel bit (high band or low band), the
resolution of the frequency deviation will remain in increments of 625 Hz. When using frequency modulation the carrier frequency will deviate from the nominal center channel carrier frequency by ±∆f:
f  fd [8 : 0]  625Hz
f
fd [8 : 0] 
f = peak deviation
625Hz
Frequency
f
fcarrier
Time
Figure 23.4. Frequency Deviation
The previous equation should be used to calculate the desired frequency deviation. If desired, frequency
modulation may also be disabled in order to obtain an unmodulated carrier signal at the channel center frequency; see “Modulation Type” on page 254 for further details.
Rev. 1.3
251
Si1000/1/2/3/4/5
Add R/W
Function/
Description
D7
71
R/W
Modulation Mode
Control 2
72
R/W
Frequency Deviation
D6
D5
D4
D3
D2
D1
D0
POR Def.
trclk[1] trclk[0] dtmod[1] dtmod[0] eninv fd[8] modtyp[1] modtyp[0]
fd[7]
fd[6]
fd[5]
fd[4]
fd[3]
fd[2]
fd[1]
fd[0]
00h
20h
23.3.6. Frequency Offset Adjustment
When the AFC is disabled the frequency offset can be adjusted manually by fo[9:0] in registers 73h and
74h. It is not possible to have both AFC and offset as internally they share the same register. The frequency offset adjustment and the AFC both are implemented by shifting the Synthesizer Local Oscillator
frequency. This register is a signed register so in order to get a negative offset it is necessary to take the
twos complement of the positive offset number. The offset can be calculated by the following:
DesiredOffset  156.25 Hz  (hbsel  1)  fo[9 : 0]
fo[9 : 0] 
DesiredOffset
156.25Hz  (hbsel  1)
The adjustment range in high band is ±160 kHz and in low band it is ±80 kHz. For example to compute an
offset of +50 kHz in high band mode fo[9:0] should be set to 0A0h. For an offset of –50 kHz in high band
mode the fo[9:0] register should be set to 360h.
Add R/W
Function/
Description
D7
D6
D5
D4
D3
D2
D1
D0
POR
Def.
fo[7]
fo[6]
fo[5]
fo[4]
fo[3]
fo[2]
fo[1]
fo[0]
00h
fo[9]
fo[8]
00h
73
R/W
Frequency Offset
74
R/W
Frequency Offset
23.3.7. Automatic Frequency Control (AFC)
All AFC settings can be easily obtained from the settings calculator. This is the recommended method to
program all AFC settings. This section is intended to describe the operation of the AFC in more detail to
help understand the trade-offs of using AFC.The receiver supports automatic frequency control (AFC) to
compensate for frequency differences between the transmitter and receiver reference frequencies. These
differences can be caused by the absolute accuracy and temperature dependencies of the reference crystals. Due to frequency offset compensation in the modem, the receiver is tolerant to frequency offsets up to
0.25 times the IF bandwidth when the AFC is disabled. When the AFC is enabled, the received signal will
be centered in the pass-band of the IF filter, providing optimal sensitivity and selectivity over a wider range
of frequency offsets up to 0.35 times the IF bandwidth. The trade-off of receiver sensitivity (at 1% PER)
versus carrier offset and the impact of AFC are illustrated in Figure 23.5.
252
Rev. 1.3
Si1000/1/2/3/4/5
Figure 23.5. Sensitivity at 1% PER vs. Carrier Frequency Offset
When AFC is enabled, the preamble length needs to be long enough to settle the AFC. In general, one
byte of preamble is sufficient to settle the AFC. Disabling the AFC allows the preamble to be shortened
from 40 bits to 32 bits. Note that with the AFC disabled, the preamble length must still be long enough to
settle the receiver and to detect the preamble (see “Preamble Length” on page 269). The AFC corrects the
detected frequency offset by changing the frequency of the Fractional-N PLL. When the preamble is
detected, the AFC will freeze for the remainder of the packet. In multi-packet mode the AFC is reset at the
end of every packet and will re-acquire the frequency offset for the next packet. The AFC loop includes a
bandwidth limiting mechanism improving the rejection of out of band signals. When the AFC loop is
enabled, its pull-in-range is determined by the bandwidth limiter value (AFCLimiter) which is located in register 2Ah.
AFC_pull_in_range = ±AFCLimiter[7:0] x (hbsel+1) x 625 Hz
The AFC Limiter register is an unsigned register and its value can be obtained from the EZRadioPRO Register Calculator spreadsheet.
The amount of error correction feedback to the Fractional-N PLL before the preamble is detected is controlled from afcgearh[2:0]. The default value 000 relates to a feedback of 100% from the measured frequency error and is advised for most applications. Every bit added will half the feedback but will require a
longer preamble to settle.
The AFC operates as follows. The frequency error of the incoming signal is measured over a period of two
bit times, after which it corrects the local oscillator via the Fractional-N PLL. After this correction, some time
is allowed to settle the Fractional-N PLL to the new frequency before the next frequency error is measured.
The duration of the AFC cycle before the preamble is detected can be programmed with shwait[2:0]. It is
advised to use the default value 001, which sets the AFC cycle to 4 bit times (2 for measurement and 2 for
settling). If shwait[2:0] is programmed to 3'b000, there is no AFC correction output. It is advised to use the
default value 001, which sets the AFC cycle to 4 bit times (2 for measurement and 2 for settling).
The AFC correction value may be read from register 2Bh. The value read can be converted to kHz with the
following formula:
AFC Correction = 156.25Hz x (hbsel +1) x afc_corr[7: 0]
Rev. 1.3
253
Si1000/1/2/3/4/5
Frequency Correction
RX
TX
AFC disabled
Freq Offset Register
Freq Offset Register
AFC enabled
AFC
Freq Offset Register
23.3.8. TX Data Rate Generator
The data rate is configurable between 0.123–256 kbps. For data rates below 30 kbps the ”txdtrtscale” bit in
register 70h should be set to 1. When higher data rates are used this bit should be set to 0.
The TX date rate is determined by the following formula in bps:
txdr  15:0   1 MHzDR_TX (bps) = -----------------------------------------------16 + 5  txdtrtscale
2
16 + 5  txdtrtscale
DR_TX(bps)  2
txdr[15:0] = --------------------------------------------------------------------------------1 MHz
For data rates higher than 100 kbps, Register 58h should be changed from its default of 80h to C0h. Nonoptimal modulation and increased eye closure will result if this setting is not made for data rates higher
than 100 kbps. The txdr register is only applicable to TX mode and does not need to be programmed for
RX mode. The RX bandwidth which is partly determined from the data rate is programmed separately.
Add R/W
Function/
Description
D7
D6
D5
D4
D3
D2
D1
D0
POR Def.
6E
R/W TX Data Rate 1
txdr[15]
txdr[14] txdr[13] txdr[12] txdr[11]
txdr[10]
txdr[9]
txdr[8]
0Ah
6F
R/W TX Data Rate 0
txdr[7]
txdr[6]
txdr[2]
txdr[1]
txdr[0]
3Dh
txdr[5]
txdr[4]
txdr[3]
23.4. Modulation Options
23.4.1. Modulation Type
The EZRadioPRO transceivers support three different modulation options: Gaussian Frequency Shift Keying (GFSK), Frequency Shift Keying (FSK), and On-Off Keying (OOK). GFSK is the recommended modulation type as it provides the best performance and cleanest modulation spectrum. Figure 23.6
demonstrates the difference between FSK and GFSK for a Data Rate of 64 kbps. The time domain plots
demonstrate the effects of the Gaussian filtering. The frequency domain plots demonstrate the spectral
benefit of GFSK over FSK. The type of modulation is selected with the modtyp[1:0] bits in "Register 71h.
Modulation Mode Control 2". Note that it is also possible to obtain an unmodulated carrier signal by setting
modtyp[1:0] = 00.
254
modtyp[1:0]
Modulation Source
00
Unmodulated Carrier
01
OOK
10
FSK
11
GFSK (enable TX Data CLK when direct mode is used)
Rev. 1.3
Si1000/1/2/3/4/5
TX Modulation Time Domain Waveforms -- FSK vs. GFSK
TX Modulation Spectrum -- FSK vs GFSK (Continuous PRBS)
-20
ModSpectrum_FSK
1.0
0.5
0.0
-0.5
-1.0
-40
-60
-80
-1.5
-100
1.0
-20
ModSpectrum_GFSK
SigData_GFSK[0,::]
SigData_FSK[0,::]
1.5
0.5
0.0
-0.5
-1.0
0
50
100
150
200
250
300
350
400
450
500
-40
-60
-80
-100
-250
-200
-150
-100
-50
0
50
100
150
200
250
freq, KHz
time, usec
DataRate
64000.0
TxDev
BT_Filter
32000.0
ModIndex
0.5
1.0
Figure 23.6. FSK vs. GFSK Spectrums
23.4.2. Modulation Data Source
The transceiver may be configured to obtain its modulation data from one of three different sources: FIFO
mode, Direct Mode, and from a PN9 mode. In Direct Mode, the TX modulation data may be obtained from
several different input pins. These options are set through the dtmod[1:0] field in "Register 71h. Modulation
Mode Control 2".
Add R/W
71
R/W
Function/
Description
Modulation
Mode
Control 2
D7
D6
D5
D4
D3
D2
D1
D0
trclk[1] trclk[0] dtmod[1] dtmod[0] eninv fd[8] modtyp[1] modtyp[0]
dtmod[1:0]
POR Def.
00h
Data Source
00
Direct Mode using TX/RX Data via GPIO pin (GPIO configuration required)
01
Direct Mode using TX/RX Data via SDI pin (only when nSEL is high)
10
FIFO Mode
11
PN9 (internally generated)
23.4.2.1. FIFO Mode
In FIFO mode, the transmit and receive data is stored in integrated FIFO register memory. The FIFOs are
accessed via "Register 7Fh. FIFO Access," and are most efficiently accessed with burst read/write operation.
In TX mode, the data bytes stored in FIFO memory are "packaged" together with other fields and bytes of
information to construct the final transmit packet structure. These other potential fields include the Preamble, Sync word, Header, CRC checksum, etc. The configuration of the packet structure in TX mode is
Rev. 1.3
255
Si1000/1/2/3/4/5
determined by the Automatic Packet Handler (if enabled), in conjunction with a variety of Packet Handler
Registers (see Table 23.4 on page 268). If the Automatic Packet Handler is disabled, the entire desired
packet structure should be loaded into FIFO memory; no other fields (such as Preamble or Sync word are
automatically added to the bytes stored in FIFO memory). For further information on the configuration of
the FIFOs for a specific application or packet size, see “Data Handling and Packet Handler” on page 264.
In RX mode, only the bytes of the received packet structure that are considered to be "data bytes" are
stored in FIFO memory. Which bytes of the received packet are considered "data bytes" is determined by
the Automatic Packet Handler (if enabled), in conjunction with the Packet Handler Registers (see
Table 23.4 on page 268). If the Automatic Packet Handler is disabled, all bytes following the Sync word are
considered data bytes and are stored in FIFO memory. Thus, even if Automatic Packet Handling operation
is not desired, the preamble detection threshold and Sync word still need to be programmed so that the RX
Modem knows when to start filling data into the FIFO. When the FIFO is being used in RX mode, all of the
received data may still be observed directly (in real-time) by properly programming a GPIO pin as the
RXDATA output pin; this can be quite useful during application development.
When in FIFO mode, the chip will automatically exit the TX or RX State when either the ipksent or ipkvalid
interrupt occurs. The chip will return to the IDLE mode state programmed in "Register 07h. Operating
Mode and Function Control 1". For example, the chip may be placed into TX mode by setting the txon bit,
but with the pllon bit additionally set. The chip will transmit all of the contents of the FIFO and the ipksent
interrupt will occur. When this interrupt event occurs, the chip will clear the txon bit and return to TUNE
mode, as indicated by the set state of the pllon bit. If no other bits are additionally set in register 07h
(besides txon initially), then the chip will return to the STANDBY state.
In RX mode, the rxon bit will be cleared if ipkvalid occurs and the rxmpk bit (RX Multi-Packet bit, SPI Register 08h bit [4]) is not set. When the rxmpk bit is set, the part will not exit the RX state after successfully
receiving a packet, but will remain in RX mode. The microcontroller will need to decide on the appropriate
subsequent action, depending upon information such as an interrupt generated by CRC, packet valid, or
preamble detect.
23.4.2.2. Direct Mode
For legacy systems that perform packet handling within an MCU or other baseband chip, it may not be
desirable to use the FIFO. For this scenario, a Direct Mode is provided which bypasses the FIFOs entirely.
In TX direct mode, the TX modulation data is applied to an input pin of the chip and processed in "real
time" (i.e., not stored in a register for transmission at a later time). A variety of pins may be configured for
use as the TX Data input function.
Furthermore, an additional pin may be required for a TX Clock output function if GFSK modulation is
desired (only the TX Data input pin is required for FSK). Two options for the source of the TX Data are
available in the dtmod[1:0] field, and various configurations for the source of the TX Data Clock may be
selected through the trclk[1:0] field.
trclk[1:0]
TX/RX Data Clock Configuration
00
01
10
11
No TX Clock (only for FSK)
TX/RX Data Clock is available via GPIO (GPIO needs programming accordingly as well)
TX/RX Data Clock is available via SDO pin (only when nSEL is high)
TX/RX Data Clock is available via the nIRQ pin
The eninv bit in SPI Register 71h will invert the TX Data; this is most likely useful for diagnostic and testing
purposes.
In RX direct mode, the RX Data and RX Clock can be programmed for direct (real-time) output to GPIO
pins. The microcontroller may then process the RX data without using the FIFO or packet handler functions
256
Rev. 1.3
Si1000/1/2/3/4/5
of the RFIC. In RX direct mode, the chip must still acquire bit timing during the Preamble, and thus the preamble detection threshold (SPI Register 35h) must still be programmed. Once the preamble is detected,
certain bit timing functions within the RX Modem change their operation for optimized performance over
the remainder of the packet. It is not required that a Sync word be present in the packet in RX Direct mode;
however, if the Sync word is absent then the skipsyn bit in SPI Register 33h must be set, or else the bit timing and tracking function within the RX Modem will not be configured for optimum performance.
23.4.2.3. Direct Synchronous Mode
In TX direct mode, the chip may be configured for synchronous or asynchronous modes of modulation. In
direct synchronous mode, the RFIC is configured to provide a TX Clock signal as an output to the external
device that is providing the TX Data stream. This TX Clock signal is a square wave with a frequency equal
to the programmed data rate. The external modulation source (e.g., MCU) must accept this TX Clock signal as an input and respond by providing one bit of TX Data back to the RFIC, synchronous with one edge
of the TX Clock signal. In this fashion, the rate of the TX Data input stream from the external source is controlled by the programmed data rate of the RFIC; no TX Data bits are made available at the input of the
RFIC until requested by another cycle of the TX Clock signal. The TX Data bits supplied by the external
source are transmitted directly in real-time (i.e., not stored internally for later transmission).
All modulation types (FSK/GFSK/OOK) are valid in TX direct synchronous mode. As will be discussed in
the next section, there are limits on modulation types in TX direct asynchronous mode.
23.4.2.4. Direct Asynchronous Mode
In TX direct asynchronous mode, the RFIC no longer controls the data rate of the TX Data input stream.
Instead, the data rate is controlled only by the external TX Data source; the RFIC simply accepts the data
applied to its TX Data input pin, at whatever rate it is supplied. This means that there is no longer a need
for a TX Clock output signal from the RFIC, as there is no synchronous "handshaking" between the RFIC
and the external data source. The TX Data bits supplied by the external source are transmitted directly in
real-time (i.e., not stored internally for later transmission).
It is not necessary to program the data rate parameter when operating in TX direct asynchronous mode.
The chip still internally samples the incoming TX Data stream to determine when edge transitions occur;
however, rather than sampling the data at a pre-programmed data rate, the chip now internally samples
the incoming TX Data stream at its maximum possible oversampling rate. This allows the chip to accurately determine the timing of the bit edge transitions without prior knowledge of the data rate. (Of course,
it is still necessary to program the desired peak frequency deviation.)
Only FSK and OOK modulation types are valid in TX Direct Asynchronous Mode; GFSK modulation is not
available in asynchronous mode. This is because the RFIC does not have knowledge of the supplied data
rate, and thus cannot determine the appropriate Gaussian lowpass filter function to apply to the incoming
data.
Rev. 1.3
257
Px.x
nIRQ
XIN
XOUT
SDN
Si1000/1/2/3/4/5
VDD_DIG
VDD_RF
Matching
TX
Px.x
RXp
Px.x
RXn
Direct synchronous modulation. Full
control over the serial interface & using
interrupt. Bitrate clock and modulation
via GPIO’s.
GPIO_2
VR_DIG
GPIO_1
ANT_A
GPIO_0
NC
GPIO configuration
GP1 : TX DATA clock output
GP2 : TX DATA input
DataCLK
MOD(Data)
Px.x
nIRQ
XOUT
XIN
SDN
Figure 23.7. Direct Synchronous Mode Example
VDD_DIG
VDD_RF
Px.x
TX
Matching
Direct asynchronous FSK modulation.
Modulation data via GPIO2, no data
clock needed in this mode.
RXp
RXn
GPIO configuration
GP2 : TX DATA input
GPIO_2
VR_DIG
GPIO_1
ANT_A
GPIO_0
NC
MOD(Data)
Figure 23.8. Direct Asynchronous Mode Example
23.4.2.5. Direct Mode using SPI or nIRQ Pins
It is possible to use the EZRadioPRO Serial Interface signals and nIRQ as the modulation clock and data.
The MISO signal can be configured to be the data clock by programming trclk = 10. If the NSS signal is
LOW then the function of the MISO signal will be SPI data output. If the NSS signal is high and trclk[1:0] is
10 then during RX and TX modes the data clock will be available on the MISO signal. If trclk[1:0] is set to
11 and no interrupts are enabled in registers 05 or 06h, then the nIRQ pin can also be used as the TX/RX
data clock.
Note: The MISO and NSS signals are internal connections. The nIRQ signal is accessed through an
external package pin.
The MOSI signal can be configured to be the data source in both RX and TX modes if dtmod[1:0] = 01. In
a similar fashion, if NSS is LOW the MOSI signal will function as SPI data-in. If NSS is HIGH then in TX
258
Rev. 1.3
Si1000/1/2/3/4/5
mode it will be the data to be modulated and transmitted. In RX mode it will be the received demodulated
data. Figure 23.9 demonstrates using MOSI and MISO as the TX/RX data and clock:
TX on
command
TX mode
TX off
command
RX on
command
RX mode
RX off
command
NSS
MOSI
SPI input
don’t care
SPI input
MOD input
SPI input
don’t care
SPI input
Data output
SPI input
MSIO
SPI output
don’t care
SPI output
Data CLK
Output
SPI output
don’t care
SPI output
Data CLK
Output
SPI output
Figure 23.9. Microcontroller Connections
If the MISO pin is not used for data clock then it may be programmed to be the interrupt function (nIRQ) by
programming Reg 0Eh bit 3.
23.4.3. PN9 Mode
In this mode the TX Data is generated internally using a pseudorandom (PN9 sequence) bit generator. The
primary purpose of this mode is for use as a test mode to observe the modulated spectrum without having
to provide data.
23.5. Internal Functional Blocks
This section provides an overview some of the key blocks of the internal radio architecture.
23.5.1. RX LNA
Depending on the part, the input frequency range for the LNA is between 240–960 MHz. The LNA provides
gain with a noise figure low enough to suppress the noise of the following stages. The LNA has one step of
gain control which is controlled by the analog gain control (AGC) algorithm. The AGC algorithm adjusts the
gain of the LNA and PGA so the receiver can handle signal levels from sensitivity to +5 dBm with optimal
performance.
In the Si1002/3, the TX and RX may be tied directly. See the TX/RX direct-tie reference design available
on www.silabs.com. When the direct tie is used the lna_sw bit in Register 6Dh, TX Power must be set.
23.5.2. RX I-Q Mixer
The output of the LNA is fed internally to the input of the receive mixer. The receive mixer is implemented
as an I-Q mixer that provides both I and Q channel outputs to the programmable gain amplifier. The mixer
consists of two double-balanced mixers whose RF inputs are driven in parallel, local oscillator (LO) inputs
are driven in quadrature, and separate I and Q Intermediate Frequency (IF) outputs drive the programmable gain amplifier. The receive LO signal is supplied by an integrated VCO and PLL synthesizer operating
between 240–960 MHz. The necessary quadrature LO signals are derived from the divider at the VCO output.
23.5.3. Programmable Gain Amplifier
The programmable gain amplifier (PGA) provides the necessary gain to boost the signal level into the
dynamic range of the ADC. The PGA must also have enough gain switching to allow for large input signals
to ensure a linear RSSI range up to –20 dBm. The PGA has steps of 3 dB which are controlled by the AGC
algorithm in the digital modem.
Rev. 1.3
259
Si1000/1/2/3/4/5
23.5.4. ADC
The amplified IQ IF signals are digitized using an Analog-to-Digital Converter (ADC), which allows for low
current consumption and high dynamic range. The bandpass response of the ADC provides exceptional
rejection of out of band blockers.
23.5.5. Digital Modem
Using high-performance ADCs allows channel filtering, image rejection, and demodulation to be performed
in the digital domain, resulting in reduced area while increasing flexibility. The digital modem performs the
following functions:








Channel selection filter
TX modulation
RX demodulation
AGC
Preamble detector
Invalid preamble detector
Radio signal strength indicator (RSSI)
Automatic frequency compensation (AFC)
Packet handling including EZMAC® features
 Cyclic redundancy check (CRC)
The digital channel filter and demodulator are optimized for ultra low power consumption and are highly
configurable. Supported modulation types are GFSK, FSK, and OOK. The channel filter can be configured
to support bandwidths ranging from 620 kHz down to 2.6 kHz. A large variety of data rates are supported
ranging from 0.123 up to 256 kbps. The AGC algorithm is implemented digitally using an advanced control
loop optimized for fast response time.

The configurable preamble detector is used to improve the reliability of the sync-word detection. The syncword detector is only enabled when a valid preamble is detected, significantly reducing the probability of
false detection.
The received signal strength indicator (RSSI) provides a measure of the signal strength received on the
tuned channel. The resolution of the RSSI is 0.5 dB. This high resolution RSSI enables accurate channel
power measurements for clear channel assessment (CCA), carrier sense (CS), and listen before talk (LBT)
functionality.
Frequency mistuning caused by crystal inaccuracies can be compensated by enabling the digital automatic frequency control (AFC) in receive mode.
A comprehensive programmable packet handler including key features of Silicon Labs’ EZMAC is integrated to create a variety of communication topologies ranging from peer-to-peer networks to mesh networks. The extensive programmability of the packet header allows for advanced packet filtering which in
turn enables a mix of broadcast, group, and point-to-point communication.
A wireless communication channel can be corrupted by noise and interference, and it is therefore important to know if the received data is free of errors. A cyclic redundancy check (CRC) is used to detect the
presence of erroneous bits in each packet. A CRC is computed and appended at the end of each transmitted packet and verified by the receiver to confirm that no errors have occurred. The packet handler and
CRC can significantly reduce the load on the microcontroller reducing the overall current consumption.
The digital modem includes the TX modulator which converts the TX data bits into the corresponding
stream of digital modulation values to be summed with the fractional input to the sigma-delta modulator.
This modulation approach results in highly accurate resolution of the frequency deviation. A Gaussian filter
is implemented to support GFSK, considerably reducing the energy in the adjacent channels. The default
bandwidth-time product (BT) is 0.5 for all programmed data rates, but it may be adjusted to other values.
260
Rev. 1.3
Si1000/1/2/3/4/5
23.5.6. Synthesizer
An integrated Sigma Delta (Σ∆) Fractional-N PLL synthesizer capable of operating from 240–960 MHz is
provided on-chip. Using a Σ∆ synthesizer has many advantages; it provides flexibility in choosing data
rate, deviation, channel frequency, and channel spacing. The transmit modulation is applied directly to the
loop in the digital domain through the fractional divider which results in very precise accuracy and control
over the transmit deviation.
Depending on the part, the PLL and - modulator scheme is designed to support any desired frequency
and channel spacing in the range from 240–960 MHz with a frequency resolution of 156.25 Hz (Low band)
or 312.5 Hz (High band). The transmit data rate can be programmed between 0.123–256 kbps, and the
frequency deviation can be programmed between ±1–320 kHz. These parameters may be adjusted via
registers as shown in “Frequency Control” on page 248.
TX
Fref = 10 M
PFD
CP
Selectable
Divider
LPF
RX
VCO
N
TX
Modulation
DeltaSigma
Figure 23.10. PLL Synthesizer Block Diagram
The reference frequency to the PLL is 10 MHz. The PLL utilizes a differential L-C VCO, with integrated onchip inductors. The output of the VCO is followed by a configurable divider which will divide down the signal to the desired output frequency band. The modulus of the variable divide-by-N divider stage is controlled dynamically by the output from the - modulator. The tuning resolution is sufficient to tune to the
commanded frequency with a maximum accuracy of 312.5 Hz anywhere in the range between 240–
960 MHz.
23.5.6.1. VCO
The output of the VCO is automatically divided down to the correct output frequency depending on the
hbsel and fb[4:0] fields in "Register 75h. Frequency Band Select". In receive mode, the LO frequency is
automatically shifted downwards by the IF frequency of 937.5 kHz, allowing transmit and receive operation
on the same frequency. The VCO integrates the resonator inductor and tuning varactor, so no external
VCO components are required.
The VCO uses a capacitance bank to cover the wide frequency range specified. The capacitance bank will
automatically be calibrated every time the synthesizer is enabled. In certain fast hopping applications this
might not be desirable so the VCO calibration may be skipped by setting the appropriate register.
Rev. 1.3
261
Si1000/1/2/3/4/5
23.5.7. Power Amplifier
The Si1000/1 contains an internal integrated power amplifier (PA) capable of transmitting at output levels
between +1 and +20 dBm. The Si1002/3/4/5 contains a PA which is capable of transmitting output levels
between –8 to +13 dBm. The PA design is single-ended and is implemented as a two stage class CE
amplifier with a high efficiency when transmitting at maximum power. The PA efficiency can only be optimized at one power level. Changing the output power by adjusting txpow[2:0] will scale both the output
power and current but the efficiency will not remain constant. The PA output is ramped up and down to prevent unwanted spectral splatter.
In the Si1002/3 the TX and RX may be tied directly. See the TX/RX direct-tie reference design available on
the Silicon Labs website for more details. When the direct tie is used the lna_sw bit in Register 6Dh, TX
Power must be set to 1.
23.5.7.1. Output Power Selection
The output power is configurable in 3 dB steps with the txpow[2:0] field in "Register 6Dh. TX Power". Extra
output power can allow the use of a cheaper smaller antenna, greatly reducing the overall BOM cost. The
higher power setting of the chip achieves maximum possible range, but of course comes at the cost of
higher TX current consumption. However, depending on the duty cycle of the system, the effect on battery
life may be insignificant. Contact Silicon Labs Support for help in evaluating this tradeoff.
Add R/W
6D
R/W
Function/
Description
TX Power
D7
D6
D4
D3
D2
reserved reserved reserved reserved lna_sw txpow[2]
txpow[2:0]
000
001
010
011
100
101
110
111
txpow[2:0]
000
001
010
011
100
101
110
111
262
D5
Si10x0/1 Output Power
+1 dBm
+2 dBm
+5 dBm
+8 dBm
+11 dBm
+14 dBm
+17 dBm
+20 dBm
Si10x2/3/4/5 Output
Power
–8 dBm
–5 dBm
–2 dBm
+1 dBm
+4 dBm
+7 dBm
+10 dBm
+13 dBm
Rev. 1.3
D1
D0
txpow[1] txpow[0]
POR
Def.
18h
Si1000/1/2/3/4/5
23.5.8. Crystal Oscillator
The transceiver includes an integrated 30 MHz crystal oscillator with a fast start-up time of less than
600 µs when a suitable parallel resonant crystal is used. The design is differential with the required crystal
load capacitance integrated on-chip to minimize the number of external components. By default, all that is
required off-chip is the 30 MHz crystal.
The crystal load capacitance can be digitally programmed to accommodate crystals with various load
capacitance requirements and to adjust the frequency of the crystal oscillator. The tuning of the crystal load
capacitance is programmed through the xlc[6:0] field of "Register 09h. 30 MHz Crystal Oscillator Load
Capacitance". The total internal capacitance is 12.5 pF and is adjustable in approximately 127 steps
(97fF/step). The xtalshift bit provides a coarse shift in frequency but is not binary with xlc[6:0].
The crystal frequency adjustment can be used to compensate for crystal production tolerances. Utilizing
the on-chip temperature sensor and suitable control software, the temperature dependency of the crystal
can be canceled.
The typical value of the total on-chip capacitance Cint can be calculated as follows:
Cint = 1.8 pF + 0.085 pF x xlc[6:0] + 3.7 pF x xtalshift
Note that the coarse shift bit xtalshift is not binary with xlc[6:0]. The total load capacitance Cload seen by
the crystal can be calculated by adding the sum of all external parasitic PCB capacitances Cext to Cint. If
the maximum value of Cint (16.3 pF) is not sufficient, an external capacitor can be added for exact tuning.
Additional information on calculating Cext and crystal selection guidelines is provided in “AN417: Si4x3x
Family Crystal Oscillator.”
If AFC is disabled then the synthesizer frequency may be further adjusted by programming the Frequency
Offset field fo[9:0]in "Register 73h. Frequency Offset 1" and "Register 74h. Frequency Offset 2", as discussed in “Frequency Control” on page 248.
The crystal oscillator frequency is divided down internally and may be output to the microcontroller through
one of the GPIO pins for use as the System Clock. In this fashion, only one crystal oscillator is required for
the entire system and the BOM cost is reduced. The available clock frequencies and GPIO configuration
are discussed further in “Output Clock” on page 273.
The transceiver may also be driven with an external 30 MHz clock signal through the XOUT pin. When
driving with an external reference or using a TCXO, the XTAL load capacitance register should be set to 0.
Add R/W Function/Description
09
R/W
Crystal Oscillator Load
Capacitance
D7
D6
D5
D4
D3
D2
D1
D0
POR
Def.
xtalshift
xlc[6]
xlc[5]
xlc[4]
xlc[3]
xlc[2]
xlc[1]
xlc[0]
7Fh
23.5.9. Regulators
There are a total of six regulators integrated onto the transceiver. With the exception of the digital regulator,
all regulators are designed to operate with only internal decoupling. The digital regulator requires an external 1 µF decoupling capacitor. All regulators are designed to operate with an input supply voltage from
+1.8 to +3.6 V. The output stage of the of PA is not connected internally to a regulator and is connected
directly to the battery voltage.
A supply voltage should only be connected to the VDD pins. No voltage should be forced on the digital regulator output.
Rev. 1.3
263
Si1000/1/2/3/4/5
23.6. Data Handling and Packet Handler
The internal modem is designed to operate with a packet including a 010101... preamble structure. To configure the modem to operate with packet formats without a preamble or other legacy packet structures contact customer support.
23.6.1. RX and TX FIFOs
Two 64 byte FIFOs are integrated into the chip, one for RX and one for TX, as shown in Figure 23.11.
"Register 7Fh. FIFO Access" is used to access both FIFOs. A burst write to address 7Fh will write data to
the TX FIFO. A burst read from address 7Fh will read data from the RX FIFO.
TX FIFO
RX FIFO
RX FIFO Almost Full
Threshold
TX FIFO Almost Full
Threshold
TX FIFO Almost Empty
Threshold
Figure 23.11. FIFO Thresholds
The TX FIFO has two programmable thresholds. An interrupt event occurs when the data in the TX FIFO
reaches these thresholds. The first threshold is the FIFO almost full threshold, txafthr[5:0]. The value in this
register corresponds to the desired threshold value in number of bytes. When the data being filled into the
TX FIFO crosses this threshold limit, an interrupt to the microcontroller is generated so the chip can enter
TX mode to transmit the contents of the TX FIFO. The second threshold for TX is the FIFO almost empty
threshold, txaethr[5:0]. When the data being shifted out of the TX FIFO drops below the almost empty
threshold an interrupt will be generated. If more data is not loaded into the FIFO then the chip
automatically exits the TX State after the ipksent interrupt occurs. The chip will return to the mode selected
by the remaining bits in SPI Register 07h. For example, the chip may be placed into TX mode by setting
the txon bit, but with the xton bit additionally set. For this condition, the chip will transmit all of the contents
of the FIFO and the ipksent interrupt will occur. When this interrupt event occurs, the chip will clear the txon
bit and return to READY mode, as indicated by the set state of the xton bit. If the pllon bit D1 is set when
entering TX mode (i.e., SPI Register 07h = 0Ah), the chip will exit from TX mode after sending the packet
and return to TUNE mode.
However, the chip will not automatically return to STANDBY mode upon exit from the TX state, in the event
the TX packet is initiated by setting SPI Register 07h = 08h (i.e., setting only txon bit D3). The chip will
instead return to READY mode, with the crystal oscillator remaining enabled. This is intentional; the system may be configured such that the host MCU derives its clock from the MCU_CLK output of the RFIC
(through GPIO2), and this clock signal must not be shut down without allowing the host MCU time to process any interrupt signals that may have occurred. The host MCU must subsequently perform a WRITE to
SPI Register 07h = 00h to enter STANDBY mode and obtain minimum current consumption.
264
Rev. 1.3
Si1000/1/2/3/4/5
Add R/W
Function/
Description
D7
D6
D5
D4
D3
D2
D1
D0
POR
Def.
antdiv[2]
antdiv[1]
antdiv[0]
rxmpk
autotx
enldm
ffclrrx
ffclrtx
00h
08
R/W
Operating &
Function
Control 2
7C
R/W
TX FIFO
Control 1
Reserved Reserved txafthr[5]
7D
R/W
TX FIFO
Control 2
Reserved Reserved txaethr[5] txaethr[4] txaethr[3] txaethr[2] txaethr[1] txaethr[0] 04h
txafthr[4] txafthr[3] txafthr[2] txafthr[1] txafthr[0]
37h
The RX FIFO has one programmable threshold called the FIFO Almost Full Threshold, rxafthr[5:0]. When
the incoming RX data crosses the Almost Full Threshold an interrupt will be generated to the microcontroller via the nIRQ pin. The microcontroller will then need to read the data from the RX FIFO.
Add R/W
7E
R/W
Function/
Description
RX FIFO
Control
D7
D6
D5
D4
D3
D2
D1
D0
Reserved Reserved rxafthr[5] rxafthr[4] rxafthr[3] rxafthr[2] rxafthr[1] rxafthr[0]
POR
Def.
37h
Both the TX and RX FIFOs may be cleared or reset with the ffclrtx and ffclrrx bits. All interrupts may be
enabled by setting the Interrupt Enabled bits in "Register 05h. Interrupt Enable 1" and “Register 06h. Interrupt Enable 2.” If the interrupts are not enabled the function will not generate an interrupt on the nIRQ pin
but the bits will still be read correctly in the Interrupt Status registers.
23.6.2. Packet Configuration
When using the FIFOs, automatic packet handling may be enabled for TX mode, RX mode, or both. "Register 30h. Data Access Control" through “Register 4Bh. Received Packet Length” control the configuration,
status, and decoded RX packet data for Packet Handling. The usual fields for network communication
(such as preamble, synchronization word, headers, packet length, and CRC) can be configured to be automatically added to the data payload. The fields needed for packet generation normally change infrequently
and can therefore be stored in registers. Automatically adding these fields to the data payload greatly
reduces the amount of communication between the microcontroller and the transceiver.
Packet Length
Data
1-4 Bytes
CRC
0 or 2
Bytes
0 or 1 Byte
0-4 Bytes
1-255 Bytes
TX Header
Preamble
Sync Word
The general packet structure is shown in Figure 23.12. The length of each field is shown below the field.
The preamble pattern is always a series of alternating ones and zeros, starting with a zero. All the fields
have programmable lengths to accommodate different applications. The most common CRC polynominals
are available for selection.
Figure 23.12. Packet Structure
An overview of the packet handler configuration registers is shown in Table 23.4.
Rev. 1.3
265
Si1000/1/2/3/4/5
23.6.3. Packet Handler TX Mode
If the TX packet length is set the packet handler will send the number of bytes in the packet length field
before returning to IDLE mode and asserting the packet sent interrupt. To resume sending data from the
FIFO the microcontroller needs to command the chip to re-enter TX mode. Figure 23.13 provides an example transaction where the packet length is set to three bytes.
D ata
D ata
D ata
D ata
D ata
D ata
D ata
D ata
D ata
1
2
3
4
5
6
7
8
9
}
}
}
This w ill be sent in the first transm ission
This w ill be sent in the second transm ission
This w ill be sent in the third transm ission
Figure 23.13. Multiple Packets in TX Packet Handler
23.6.4. Packet Handler RX Mode
23.6.4.1. Packet Handler Disabled
When the packet handler is disabled certain fields in the received packet are still required. Proper modem
operation requires preamble and sync when the FIFO is being used, as shown in Figure 23.14. Bits after
sync will be treated as raw data with no qualification. This mode allows for the creation of a custom packet
handler when the automatic qualification parameters are not sufficient. Manchester encoding is supported
but data whitening, CRC, and header checks are not.
Preamble
SYNC
DATA
Figure 23.14. Required RX Packet Structure with Packet Handler Disabled
23.6.4.2. Packet Handler Enabled
When the packet handler is enabled, all the fields of the packet structure need to be configured. Register
contents are used to construct the header field and length information encoded into the transmitted packet
when transmitting. The receive FIFO can be configured to handle packets of fixed or variable length with or
without a header. If multiple packets are desired to be stored in the FIFO, then there are options available
for the different fields that will be stored into the FIFO. Figure 23.15 demonstrates the options and settings
available when multiple packets are enabled. Figure 23.16 demonstrates the operation of fixed packet
length and correct/incorrect packets.
266
Rev. 1.3
Si1000/1/2/3/4/5
RX FIFO Contents:
Transmission:
rx_multi_pk_en = 0
rx_multi_pk_en = 1
Register
Data
Header(s)
txhdlen = 0
Register
Data
Length
0
txhdlen > 0
fixpklen
fixpklen
0
1
Data
1
H
H
FIFO
L
Data
L
Data
Data
Data
Data
Figure 23.15. Multiple Packets in RX Packet Handler
Initial state
RX FIFO Addr.
0
PK 1 OK
Write
Pointer
RX FIFO Addr.
0
PK 2 OK
RX FIFO Addr.
0
H
L
Write
Pointer
PK 4 OK
RX FIFO Addr.
0
RX FIFO Addr.
0
H
L
H
L
Data
Data
Data
H
L
Data
H
L
Data
H
L
Data
H
L
Data
PK 3
ERROR
Write
Pointer
H
Write
Pointer
H
L
L
Data
63
63
63
63
Data
Write
Pointer
CRC
error
63
Figure 23.16. Multiple Packets in RX with CRC or Header Error
Rev. 1.3
267
Si1000/1/2/3/4/5
Table 23.4. Packet Handler Registers
Add
R/W
Function/Description
D7
D6
D5
D4
D3
D2
D1
enpacrx
lsbfrst
crcdonly
skip2ph
0
rxcrc1
pksrch
pkrx
30
R/W
Data Access Control
31
R
EzMAC status
enpactx
encrc
pkvalid
crcerror
32
R/W
Header Control 1
33
R/W
Header Control 2
skipsyn
hdlen[2]
hdlen[1]
hdlen[0]
fixpklen
synclen[1]
synclen[0]
prealen[8]
22h
34
R/W
Preamble Length
prealen[7]
prealen[6]
prealen[5]
prealen[4]
prealen[3]
prealen[2]
prealen[1]
prealen[0]
08h
35
R/W
Preamble Detection Control
preath[4]
preath[3]
preath[2]
preath[1]
preath[0]
rssi_off[2]
rssi_off[1]
rssi_off[0]
2Ah
36
R/W
Sync Word 3
sync[31]
sync[30]
sync[29]
sync[28]
sync[27]
sync[26]
sync[25]
sync[24]
2Dh
37
R/W
Sync Word 2
sync[23]
sync[22]
sync[21]
sync[20]
sync[19]
sync[18]
sync[17]
sync[16]
D4h
38
R/W
Sync Word 1
sync[15]
sync[14]
sync[13]
sync[12]
sync[11]
sync[10]
sync[9]
sync[8]
00h
39
R/W
Sync Word 0
sync[7]
sync[6]
sync[5]
sync[4]
sync[3]
sync[2]
sync[1]
sync[0]
00h
3A
R/W
Transmit Header 3
txhd[31]
txhd[30]
txhd[29]
txhd[28]
txhd[27]
txhd[26]
txhd[25]
txhd[24]
00h
3B
R/W
Transmit Header 2
txhd[23]
txhd[22]
txhd[21]
txhd[20]
txhd[19]
txhd[18]
txhd[17]
txhd[16]
00h
3C
R/W
Transmit Header 1
txhd[15]
txhd[14]
txhd[13]
txhd[12]
txhd[11]
txhd[10]
txhd[9]
txhd[8]
00h
3D
R/W
Transmit Header 0
txhd[7]
txhd[6]
txhd[5]
txhd[4]
txhd[3]
txhd[2]
txhd[1]
txhd[0]
00h
3E
R/W
Transmit Packet Length
pklen[7]
pklen[6]
pklen[5]
pklen[4]
pklen[3]
pklen[2]
pklen[1]
pklen[0]
00h
3F
R/W
Check Header 3
chhd[31]
chhd[30]
chhd[29]
chhd[28]
chhd[27]
chhd[26]
chhd[25]
chhd[24]
00h
40
R/W
Check Header 2
chhd[23]
chhd[22]
chhd[21]
chhd[20]
chhd[19]
chhd[18]
chhd[17]
chhd[16]
00h
41
R/W
Check Header 1
chhd[15]
chhd[14]
chhd[13]
chhd[12]
chhd[11]
chhd[10]
chhd[9]
chhd[8]
00h
bcen[3:0]
D0
POR
Def
crc[1]
crc[0]
8Dh
pktx
pksent
hdch[3:0]
—
0Ch
42
R/W
Check Header 0
chhd[7]
chhd[6]
chhd[5]
chhd[4]
chhd[3]
chhd[2]
chhd[1]
chhd[0]
00h
43
R/W
Header Enable 3
hden[31]
hden[30]
hden[29]
hden[28]
hden[27]
hden[26]
hden[25]
hden[24]
FFh
44
R/W
Header Enable 2
hden[23]
hden[22]
hden[21]
hden[20]
hden[19]
hden[18]
hden[17]
hden[16]
FFh
45
R/W
Header Enable 1
hden[15]
hden[14]
hden[13]
hden[12]
hden[11]
hden[10]
hden[9]
hden[8]
FFh
46
R/W
Header Enable 0
hden[7]
hden[6]
hden[5]
hden[4]
hden[3]
hden[2]
hden[1]
hden[0]
FFh
47
R
Received Header 3
rxhd[31]
rxhd[30]
rxhd[29]
rxhd[28]
rxhd[27]
rxhd[26]
rxhd[25]
rxhd[24]
—
48
R
Received Header 2
rxhd[23]
rxhd[22]
rxhd[21]
rxhd[20]
rxhd[19]
rxhd[18]
rxhd[17]
rxhd[16]
—
49
R
Received Header 1
rxhd[15]
rxhd[14]
rxhd[13]
rxhd[12]
rxhd[11]
rxhd[10]
rxhd[9]
rxhd[8]
—
4A
R
Received Header 0
rxhd[7]
rxhd[6]
rxhd[5]
rxhd[4]
rxhd[3]
rxhd[2]
rxhd[1]
rxhd[0]
—
4B
R
Received Packet Length
rxplen[7]
rxplen[6]
rxplen[5]
rxplen[4]
rxplen[3]
rxplen[2]
rxplen[1]
rxplen[0]
—
23.6.5. Data Whitening, Manchester Encoding, and CRC
Data whitening can be used to avoid extended sequences of 0s or 1s in the transmitted data stream to
achieve a more uniform spectrum. When enabled, the payload data bits are XORed with a pseudorandom
sequence output from the built-in PN9 generator. The generator is initialized at the beginning of the payload. The receiver recovers the original data by repeating this operation. Manchester encoding can be
used to ensure a dc-free transmission and good synchronization properties. When Manchester encoding is
used, the effective datarate is unchanged but the actual datarate (preamble length, etc.) is doubled due to
the nature of the encoding. The effective datarate when using Manchester encoding is limited to 128 kbps.
The implementation of Manchester encoding is shown in Figure 23.18. Data whitening and Manchester
encoding can be selected with "Register 70h. Modulation Mode Control 1". The CRC is configured via
"Register 30h. Data Access Control". Figure 23.17 demonstrates the portions of the packet which have
Manchester encoding, data whitening, and CRC applied. CRC can be applied to only the data portion of
the packet or to the data, packet length and header fields. Figure 23.18 provides an example of how the
Manchester encoding is done and also the use of the Manchester invert (enmaniv) function.
268
Rev. 1.3
Si1000/1/2/3/4/5
Manchester
Whitening
CRC
CRC
(Over data only)
Preamble
Header/
Address
Sync
PK
Length
Data
CRC
Figure 23.17. Operation of Data Whitening, Manchester Encoding, and CRC
Data before Manchester
1
1
1
1
1
Preamble = 0xFF
1
1
1
0
0
0
1
0
First 4bits of the synch. word = 0x2
Data after Machester ( manppol = 1, enmaninv = 0)
Data after Machester ( manppol = 1, enmaninv = 1)
Data before Manchester
0
0
0
0
0
Preamble = 0x00
0
0
0
0
0
0
1
0
First 4bits of the synch. word = 0x2
Data after Machester ( manppol = 0, enmaninv = 0)
Data after Machester ( manppol = 0, enmaninv = 1)
Figure 23.18. Manchester Coding Example
23.6.6. Preamble Detector
The EZRadioPRO transceiver has integrated automatic preamble detection. The preamble length is configurable from 1–255 bytes using the prealen[7:0] field in "Register 33h. Header Control 2" and "Register
34h. Preamble Length", as described in “23.6.2. Packet Configuration” . The preamble detection threshold,
preath[4:0] as set in "Register 35h. Preamble Detection Control 1", is in units of 4 bits. The preamble
detector searches for a preamble pattern with a length of preath[4:0].
If a false preamble detect occurs, the receiver will continuing searching for the preamble when no sync
word is detected. Once preamble is detected (false or real) then the part will then start searching for sync.
If no sync occurs then a timeout will occur and the device will initiate search for preamble again. The timeout period is defined as the sync word length plus four bits and will start after a non-preamble pattern is
recognized after a valid preamble detection. The preamble detector output may be programmed onto one
of the GPIO or read in the interrupt status registers.
23.6.7. Preamble Length
The preamble detection threshold determines the number of valid preamble bits the radio must receive to
qualify a valid preamble. The preamble threshold should be adjusted depending on the nature of the application. The required preamble length threshold will depend on when receive mode is entered in relation to
the start of the transmitted packet and the length of the transmit preamble. With a shorter than recommended preamble detection threshold the probability of false detection is directly related to how long the
receiver operates on noise before the transmit preamble is received. False detection on noise may cause
the actual packet to be missed. The preamble detection threshold is programmed in register 35h. For most
applications with a preamble length longer than 32 bits the default value of 20 is recommended for the pre-
Rev. 1.3
269
Si1000/1/2/3/4/5
amble detection threshold. A shorter Preamble Detection Threshold may be chosen if occasional false
detections may be tolerated. When antenna diversity is enabled a 20-bit preamble detection threshold is
recommended. When the receiver is synchronously enabled just before the start of the packet, a shorter
preamble detection threshold may be used. Table 23.5 demonstrates the recommended preamble detection threshold and preamble length for various modes.
It is possible to use the transceiver in a raw mode without the requirement for a 010101... preamble. Contact customer support for further details.
Table 23.5. Minimum Receiver Settling Time
Mode
(G)FSK AFC Disabled
(G)FSK AFC Enabled
(G)FSK AFC Disabled
+Antenna Diversity Enabled
(G)FSK AFC Enabled
+Antenna Diversity Enabled
OOK
OOK + Antenna Diversity
Enabled
Approximate
Receiver
Settling Time
1 byte
2 byte
Recommended Preamble Recommended Preamble
Length with 8-Bit
Length with 20-Bit
Detection Threshold
Detection Threshold
20 bits
32 bits
28 bits
40 bits
1 byte
—
64 bits
2 byte
—
8 byte
2 byte
3 byte
4 byte
8 byte
—
8 byte
Note: The recommended preamble length and preamble detection threshold listed above are to achieve 0% PER.
They may be shortened when occasional packet errors are tolerable.
23.6.8. Invalid Preamble Detector
When scanning channels in a frequency hopping system it is desirable to determine if a channel is valid in
the minimum amount of time. The preamble detector can output an invalid preamble detect signal. which
can be used to identify the channel as invalid. After a configurable time set in Register 60h[7:4], an invalid
preamble detect signal is asserted indicating an invalid channel. The period for evaluating the signal for
invalid preamble is defined as (inv_pre_th[3:0] x 4) x Bit Rate Period. The preamble detect and invalid preamble detect signals are available in "Register 03h. Interrupt/Status 1" and “Register 04h. Interrupt/Status
2.”
23.6.9. Synchronization Word Configuration
The synchronization word length for both TX and RX can be configured in Reg 33h, synclen[1:0]. The
expected or transmitted sync word can be configured from 1 to 4 bytes as defined below:
synclen[1:0] = 00—Expected/Transmitted Synchronization Word (sync word) 3.
 synclen[1:0] = 01—Expected/Transmitted Synchronization Word 3 first, followed by sync word 2.
 synclen[1:0] = 10—Expected/Transmitted Synchronization Word 3 first, followed by sync word 2,
followed by sync word 1.
 synclen[1:0] = 1—Send/Expect Synchronization Word 3 first, followed by sync word 2, followed by sync
word 1, followed by sync word 0.
The sync is transmitted or expected in the following sequence: sync 3sync 2sync 1sync 0. The sync
word values can be programmed in Registers 36h–39h. After preamble detection the part will search for
sync for a fixed period of time. If a sync is not recognized in this period then a timeout will occur and the
search for preamble will be re-initiated. The timeout period after preamble detections is defined as the
value programmed into the sync word length plus four additional bits.

270
Rev. 1.3
Si1000/1/2/3/4/5
23.6.10. Receive Header Check
The header check is designed to support 1–4 bytes and broadcast headers. The header length needs to
be set in register 33h, hdlen[2:0]. The headers to be checked need to be set in register 32h, hdch[3:0]. For
instance, there can be four bytes of header in the packet structure but only one byte of the header is set to
be checked (i.e., header 3). For the headers that are set to be checked, the expected value of the header
should be programmed in chhd[31:0] in Registers 3F–42. The individual bits within the selected bytes to be
checked can be enabled or disabled with the header enables, hden[31:0] in Registers 43–46. For example,
if you want to check all bits in header 3 then hden[31:24] should be set to FF but if only the last 4 bits are
desired to be checked then it should be set to 00001111 (0F). Broadcast headers can also be programmed
by setting bcen[3:0] in Register 32h. For broadcast header check the value may be either “FFh” or the
value stored in the Check Header register. A logic equivalent of the header check for Header 3 is shown in
Figure 23.19. A similar logic check will be done for Header 2, Header 1, and Header 0 if enabled.
Example for Header 3
rxhd[31:24]
BIT
WISE
Equivalence
comparison
hden[31:24]
=
BIT
WISE
chhd[31:24]
bcen[3]
header3_ok
Equivalence
comparison
FFh
=
hdch[3]
rxhd[31:24]
Figure 23.19. Header
23.6.11. TX Retransmission and Auto TX
The transceiver is capable of automatically retransmitting the last packet loaded in the TX FIFO. Automatic
retransmission is set by entering the TX state with the txon bit without reloading the TX FIFO. This feature
is useful for beacon transmission or when retransmission is required due to the absence of a valid
acknowledgment. Only packets that fit completely in the TX FIFO can be automatically retransmitted.
An automatic transmission function is available, allowing the radio to automatically start or stop a transmission depending on the amount of data in the TX FIFO.
When autotx is set in “Register 08. Operating & Function Control 2", the transceiver will automatically enter
the TX state when the TX FIFO almost full threshold is exceeded. Packets will be transmitted according to
the configured packet length. To stop transmitting, clear the packet sent or TX FIFO almost empty interrupts must be cleared by reading register.
Rev. 1.3
271
Si1000/1/2/3/4/5
23.7. RX Modem Configuration
A Microsoft Excel parameter calculator or Wireless Development Suite (WDS) calculator is provided to
determine the proper settings for the modem. The calculator can be found on www.silabs.com or on the
CD provided with the demo kits. An application note is available to describe how to use the calculator and
to provide advanced descriptions of the modem settings and calculations.
23.7.1. Modem Settings for FSK and GFSK
The modem performs channel selection and demodulation in the digital domain. The channel filter bandwidth is configurable from 2.6 to 620 kHz. The receiver data-rate, modulation index, and bandwidth are set
via registers 1C–25h. The modulation index is equal to 2 times the peak deviation divided by the data rate
(Rb).
When Manchester coding is disabled, the required channel filter bandwidth is calculated as BW = 2Fd + Rb
where Fd is the frequency deviation and Rb is the data rate.
23.8. Auxiliary Functions
The EZRadioPRO has some auxiliary functions that duplicate the directly accessible MCU peripherals:
ADC, temperature sensor, and 32 kHz oscillator. These auxiliary functions are retained primarily for compatibility with the Si4430/1/2. The directly accessed MCU peripherals typically provide lower system current consumption and better analog performance. However some of these EZRadioPRO auxiliary
functions offer features not directly duplicated in the MCU directly accessed peripherals, such as the Low
Duty Cycle Mode operation.
23.8.1. Smart Reset
The EZRadioPRO transceiver contains an enhanced integrated SMART RESET or POR circuit. The POR
circuit contains both a classic level threshold reset as well as a slope detector POR. This reset circuit was
designed to produce a reliable reset signal under any circumstances. Reset will be initiated if any of the following conditions occur:

Initial power on, VDD starts from gnd: reset is active till VDD reaches VRR (see table);

When VDD decreases below VLD for any reason: reset is active till VDD reaches VRR;

A software reset via “Register 08h. Operating Mode and Function Control 2”: reset is active for time
TSWRST

On the rising edge of a VDD glitch when the supply voltage exceeds the following time functioned limit:
VDD nom.
VDD(t)
reset limit:
0.4V+t*0.2V/ms
actual VDD(t)
showing glitch
0.4V
Reset
TP
t=0,
VDD starts to rise
t
reset:
Vglitch>=0.4+t*0.2V/ms
Figure 23.20. POR Glitch Parameters
272
Rev. 1.3
Si1000/1/2/3/4/5
Table 23.6. POR Parameters
Parameter
Release Reset Voltage
Power-On VDD Slope
Symbol
Comment
VRR
Min
Typ
Max
Unit
0.85
1.3
1.75
V
SVDD
tested VDD slope region
0.03
—
300
V/ms
VLD
VLD<VRR is guaranteed
0.7
1
1.3
V
TSWRST
50
—
470
us
Threshold Voltage
VTSD
—
0.4
—
V
Reference Slope
k
—
0.2
—
V/ms
Low VDD Limit
Software Reset Pulse
VDD Glitch Reset Pulse
TP
POR Reset Time tPOR is specified in Table 4.20 on page 70.
Also occurs after SDN, and
initial power on
The reset will initialize all registers to their default values. The reset signal is also available for output and
use by the microcontroller by using the default setting for GPIO_0. The inverted reset signal is available by
default on GPIO_1.
23.8.2. Output Clock
The 30 MHz crystal oscillator frequency is divided down internally and may be output on GPIO2. This feature is useful to lower BOM cost by using only one crystal in the system. The output clock on GPIO2 may
be routed to the XTAL2 input to provide a synchronized clock source between the MCU and the EZRadioPRO peripheral. The output clock frequency is selectable from one of 8 options, as shown below. Except
for the 32.768 kHz option, all other frequencies are derived by dividing the crystal oscillator frequency. The
32.768 kHz clock signal is derived from an internal RC oscillator or an external 32 kHz crystal. The default
setting for GPIO2 is to output the clock signal with a frequency of 1 MHz.
Add R/W
0A
R/W
Function/
Description
D7
D6
Output Clock
D5
D4
D3
clkt[1]
clkt[0]
enlfc
D2
Modulation Source
000
30 MHz
001
15 MHz
010
10 MHz
011
4 MHz
100
3 MHz
101
2 MHz
1 MHz
111
32.768 kHz
D0
mclk[2] mclk[1] mclk[0]
mclk[2:0]
110
D1
POR Def.
06h
Since the crystal oscillator is disabled in SLEEP mode in order to save current, the low-power 32.768 kHz
clock can be automatically switched to become the output clock. This feature is called enable low frequency clock and is enabled by the enlfc bit in “Register 0Ah. Microcontroller Output Clock." When enlfc =
1 and the chip is in SLEEP mode then the 32.768 kHz clock will be provided regardless of the setting of
mclk[2:0]. For example, if mclk[2:0] = 000, 30 MHz will be provided through the GPIO output pin in all IDLE,
Rev. 1.3
273
Si1000/1/2/3/4/5
TX, or RX states. When the chip enters SLEEP mode, the output clock will automatically switch to
32.768 kHz from the RC oscillator or 32.768 XTAL.
Another available feature for the output clock is the clock tail, clkt[1:0] in “Register 0Ah. Microcontroller
Output Clock." If the low frequency clock feature is not enabled (enlfc = 0), then the output is disabled in
SLEEP mode. Setting the clkt[1:0] field will provide additional cycles of the output clock before it shuts off.
clkt[1:0]
Modulation Source
00
0 cycles
01
128 cycles
10
256 cycles
11
512 cycles
If an interrupt is triggered, the output clock will remain enabled regardless of the selected mode. As soon
as the interrupt is read the state machine will then move to the selected mode. The minimum current consumption will not be achieved until the interrupt is read. For instance, if the EZRadioPRO peripheral is
commanded to SLEEP mode but an interrupt has occurred the 30 MHz XTAL will not be disabled until the
interrupt has been cleared.
23.8.3. General Purpose ADC
The EZRadioPRO peripheral includes an 8-bit SAR ADC independent of ADC0. It may be used for general
purpose analog sampling, as well as for digitizing the EZRadioPRO temperature sensor reading. In most
cases, the ADC0 subsystem directly accessible from the MCU will be preferred over the ADC embedded
inside the EZRadioPRO peripheral. Registers 0Fh "ADC Configuration", 10h "Sensor Offset" and 4Fh
"Amplifier Offset" can be used to configure the ADC operation. Details of these registers are in “AN440:
EZRadioPRO Detailed Register Descriptions.”
Every time an ADC conversion is desired, bit 7 "adcstart/adcdone" in Register 0Fh “ADC Configuration”
must be set to 1. The conversion time for the ADC is 350 µs. After the ADC conversion is done and the
adcdone signal is showing 1, then the ADC value may be read out of “Register 11h: ADC Value." When the
ADC is doing its conversion, the adcstart/adcdone bit will read 0. When the ADC has finished its conversion, the bit will be set to 1. A new ADC conversion can be initiated by writing a 1 to the adcstart/adcdone
bit.
The architecture of the ADC is shown in Figure 23.21. The signal and reference inputs of the ADC are
selected by adcsel[2:0] and adcref[1:0] in register 0Fh “ADC Configuration”, respectively. The default setting is to read out the temperature sensor using the bandgap voltage (VBG) as reference. With the VBG
reference the input range of the ADC is from 0–1.02 V with an LSB resolution of 4 mV (1.02/255). Changing the ADC reference will change the LSB resolution accordingly.
A differential multiplexer and amplifier are provided for interfacing external bridge sensors. The gain of the
amplifier is selectable by adcgain[1:0] in Register 0Fh. The majority of sensor bridges have supply voltage
(VDD) dependent gain and offset. The reference voltage of the ADC can be changed to either VDD/2 or
VDD/3. A programmable VDD dependent offset voltage can be added using soffs[3:0] in register 10h.
274
Rev. 1.3
Si1000/1/2/3/4/5
Diff. MUX
Diff. Amp.
…
…
Input MUX
aoffs [4:0]
adcsel [2:0]
GPIO0
soffs [3:0]
adcgain [1:0]
…
GPIO1
GPIO2
8-bit ADC
Temperature Sensor
Vin
adcsel [2:0]
Vref
0 -1020mV / 0-255
Ref MUX
…
VDD / 3
VDD / 2
VBG (1.2V)
adc [7:0]
adcref [1:0]
Figure 23.21. General Purpose ADC Architecture
Add
R/W
Function/
Description
D7
0F
R/W
ADC Configuration
adcstart/adcdone
10
R/W
Sensor Offset
11
R
ADC Value
adc[7]
D6
D5
adcsel[2] adcsel[1]
adc[6]
adc[5]
D4
D3
D2
adcsel[0]
adcref[1]
adcref[0]
soffs[3]
soffs[2]
soffs[1]
soffs[0]
00h
adc[3]
adc[2]
adc[1]
adc[0]
—
adc[4]
D1
D0
POR
Def.
adcgain[1] adcgain[0]
00h
23.8.4. Temperature Sensor
The EZRadioPRO peripheral includes an integrated on-chip analog temperature sensor independent of
the temperature sensor associated with ADC0. The temperature sensor will be automatically enabled
when the temperature sensor is selected as the input of the EZRadioPRO ADC or when the analog temp
voltage is selected on the analog test bus. The temperature sensor value may be digitized using the EZRadioPRO general-purpose ADC and read out through "Register 10h. ADC Sensor Amplifier Offset." The
range of the temperature sensor is configurable. Table 23.7 lists the settings for the different temperature
ranges and performance.
To use the Temp Sensor:
1. Set the input for ADC to the temperature sensor, "Register 0Fh. ADC Configuration"—adcsel[2:0] = 000
2. Set the reference for ADC, "Register 0Fh. ADC Configuration"—adcref[1:0] = 00
3. Set the temperature range for ADC, "Register 12h. Temperature Sensor Calibration"—tsrange[1:0]
4. Set entsoffs = 1, "Register 12h. Temperature Sensor Calibration"
5. Trigger ADC reading, "Register 0Fh. ADC Configuration"—adcstart = 1
6. Read temperature value—Read contents of "Register 11h. ADC Value"
Rev. 1.3
275
Si1000/1/2/3/4/5
Add
R/
W
Function/
Description
D7
D6
D5
D4
D3
D2
12
R/W
Temperature
Sensor Control
tsrange[1]
tsrange[0]
entsoffs
entstrim
tstrim[3]
tstrim[2]
13
R/W
Temperature Value
Offset
tvoffs[7]
tvoffs[6]
tvoffs[5]
tvoffs[4]
tvoffs[3]
tvoffs[2]
D1
D0
POR
Def.
vbgtrim[1] vbgtrim[0]
tvoffs[1]
tvoffs[0]
20h
00h
Table 23.7. Temperature Sensor Range
entoff
tsrange[1]
tsrange[0]
Temp. range
Unit
Slope
ADC8 LSB
1
0
0
–64 … 64
°C
8 mV/°C
0.5 °C
1
0
1
–64 … 192
°C
4 mV/°C
1 °C
1
1
0
0 … 128
°C
8 mV/°C
0.5 °C
1
1
1
–40 … 216
°F
4 mV/°F
1 °F
0*
1
0
0 … 341
°K
3 mV/°K
1.333 °K
Note: Absolute temperature mode, no temperature shift. This mode is only for test purposes. POR value of
EN_TOFF is 1.
The slope of the temperature sensor is very linear and monotonic. For absolute accuracy better than 10 °C
calibration is necessary. The temperature sensor may be calibrated by setting entsoffs = 1 in “Register
12h. Temperature Sensor Control” and setting the offset with the tvoffs[7:0] bits in “Register 13h. Temperature Value Offset.” This method adds a positive offset digitally to the ADC value that is read in “Register
11h. ADC Value.” The other method of calibration is to use the tstrim which compensates the analog circuit. This is done by setting entstrim = 1 and using the tstrim[2:0] bits to offset the temperature in “Register
12h. Temperature Sensor Control.” With this method of calibration, a negative offset may be achieved.
With both methods of calibration better than ±3 °C absolute accuracy may be achieved.
The different ranges for the temperature sensor and ADC8 are demonstrated in Figure 23.22. The value of
the ADC8 may be translated to a temperature reading by ADC8Value x ADC8 LSB + Lowest Temperature
in Temp Range. For instance for a tsrange = 00, Temp = ADC8Value x 0.5 – 64.
276
Rev. 1.3
Si1000/1/2/3/4/5
Temperature Measurement with ADC8
300
250
ADC Value
200
Sensor Range 0
Sensor Range 1
150
Sensor Range 2
Sensor Range 3
100
50
0
-40
-20
0
20
40
60
80
100
Temperature [Celsius]
Figure 23.22. Temperature Ranges using ADC8
23.8.5. Low Battery Detector
The Low Battery Detector (LBD) feature of the EZRadioPRO peripheral is not supported in the
Si1000/1/2/3/4/5. Use ADC0 instead. Refer to Section Section “5. 10-Bit SAR ADC with 16-bit Auto-Averaging Accumulator and Autonomous Low Power Burst Mode” on page 74 for details.
Rev. 1.3
277
Si1000/1/2/3/4/5
23.8.6. Wake-Up Timer and 32 kHz Clock Source
The EZRadioPRO peripheral contains an integrated wake-up timer independent of the SmaRTClock which
can be used to periodically wake the chip from SLEEP mode using the interrupt pin. The wake-up timer
runs from the internal 32.768 kHz RC Oscillator. The wake-up timer can be configured to run when in
SLEEP mode. If enwt = 1 in "Register 07h. Operating Mode and Function Control 1" when entering SLEEP
mode, the wake-up timer will count for a time specified defined in Registers 14–16h, "Wake Up Timer
Period". At the expiration of this period an interrupt will be generated on the nIRQ pin if this interrupt is
enabled. The software will then need to verify the interrupt by reading the Registers 03h–04h, "Interrupt
Status 1 & 2". The wake-up timer value may be read at any time by the wtv[15:0] read only registers 17h–
18h.
The formula for calculating the Wake-Up Period is the following:
WUT 
32  M  2 R
ms
32 .768
WUT Register
Description
wtr[4:0]
R Value in Formula
wtm[15:0]
M Value in Formula
Use of the D variable in the formula is only necessary if finer resolution is required than can be achieved by
using the R value.
278
Rev. 1.3
Si1000/1/2/3/4/5
Add R/W Function/Description
D7
D6
D5
D4
D3
D2
D1
D0
POR
Def.
wtr[4]
wtr[3]
wtr[2]
wtr[1]
wtr[0]
03h
14
R/W
Wake-Up Timer Period 1
15
R/W
Wake-Up Timer Period 2
wtm[15] wtm[14] wtm[13] wtm[12] wtm[11] wtm[10] wtm[9] wtm[8]
00h
16
R/W
Wake-Up Timer Period 3
wtm[7]
wtm[6]
wtm[5]
wtm[4]
wtm[3]
wtm[2]
wtm[1] wtm[0]
00h
17
R
Wake-Up Timer Value 1
wtv[15]
wtv[14]
wtv[13]
wtv[12]
wtv[11]
wtv[10]
wtv[9]
wtv[8]
—
18
R
Wake-Up Timer Value 2
wtv[7]
wtv[6]
wtv[5]
wtv[4]
wtv[3]
wtv[2]
wtv[1]
wtv[0]
—
There are two different methods for utilizing the wake-up timer (WUT) depending on if the WUT interrupt is
enabled in “Register 06h. Interrupt Enable 2.” If the WUT interrupt is enabled then nIRQ pin will go low
when the timer expires. The chip will also change state so that the 30 MHz XTAL is enabled so that the
microcontroller clock output is available for the microcontroller to use to process the interrupt. The other
method of use is to not enable the WUT interrupt and use the WUT GPIO setting. In this mode of operation
the chip will not change state until commanded by the microcontroller. The different modes of operating the
WUT and the current consumption impacts are demonstrated in Figure 23.23.
A 32 kHz XTAL may also be used for better timing accuracy. By setting the x32 ksel bit in Register 07h
"Operating & Function Control 1", GPIO0 is automatically reconfigured so that an external 32 kHz XTAL
may be connected to this pin. In this mode, the GPIO0 is extremely sensitive to parasitic capacitance, so
only the XTAL should be connected to this pin with the XTAL physically located as close to the pin as possible. Once the x32 ksel bit is set, all internal functions such as WUT, microcontroller clock, and LDC mode
will use the 32 kHz XTAL and not the 32 kHz RC oscillator.
The 32 kHz XTAL accuracy is comprised of both the XTAL parameters and the internal circuit. The XTAL
accuracy can be defined as the XTAL initial error + XTAL aging + XTAL temperature drift + detuning from
the internal oscillator circuit. The error caused by the internal circuit is typically less than 10 ppm.
Rev. 1.3
279
Si1000/1/2/3/4/5
Interrupt Enable enwut =1 ( Reg 06h)
WUT Period
GPIOX =00001
nIRQ
SPI Interrupt
Read
Chip State
Sleep
Current
Consumption
Ready
Sleep
Ready
1.5 mA
Sleep
1.5 mA
1 uA
1 uA
WUT Period
GPIOX =00001
nIRQ
SPI Interrupt
Read
Chip State
Sleep
Current
Consumption
1 uA
Figure 23.23. WUT Interrupt and WUT Operation
Rev. 1.3
Sleep
1.5 mA
Interrupt Enable enwut =0 ( Reg 06h)
280
Ready
1 uA
Si1000/1/2/3/4/5
23.8.7. Low Duty Cycle Mode
The Low Duty Cycle Mode is available to automatically wake-up the receiver to check if a valid signal is
available. The basic operation of the low duty cycle mode is demonstrated in the figure below. If a valid
preamble or sync word is not detected the chip will return to sleep mode until the beginning of a new WUT
period. If a valid preamble and sync are detected the receiver on period will be extended for the low duty
cycle mode duration (TLDC) to receive all of the packet. The WUT period must be set in conjunction with
the low duty cycle mode duration. The R value (“Register 14h. Wake-up Timer Period 1”) is shared
between the WUT and the TLDC. The ldc[7:0] bits are located in “Register 19h. Low Duty Cycle Mode
Duration.” The time of the TLDC is determined by the formula below:
TLDC
 ldc [ 7 : 0 ] 
42R
ms
32 . 768
Figure 23.24. Low Duty Cycle Mode
23.8.8. GPIO Configuration
Three general purpose IOs (GPIOs) are available. Numerous functions such as specific interrupts, TRSW
control, etc. can be routed to the GPIO pins as shown in the tables below. When in Shutdown mode all the
GPIO pads are pulled low.
Note: The ADC should not be selected as an input to the GPIO in standby or sleep modes and will cause excess current consumption.
Add R/W
Function/
Description
D7
D6
D5
D4
D3
D2
D1
D0
POR
Def.
0B
R/W
GPIO0
Configuration
gpio0drv[1] gpio0drv[0]
pup0
gpio0[4] gpio0[3] gpio0[2] gpio0[1] gpio0[0]
00h
0C
R/W
GPIO1
Configuration
gpio1drv[1] gpio1drv[0]
pup1
gpio1[4] gpio1[3] gpio1[2] gpio1[1] gpio1[0]
00h
0D
R/W
GPIO2
Configuration
gpio2drv[1] gpio2drv[0]
pup2
gpio2[4] gpio2[3] gpio2[2] gpio2[1] gpio2[0]
00h
0E
R/W
I/O Port
Configuration
extitst[2]
extitst[1] extitst[0]
Rev. 1.3
itsdo
dio2
dio1
dio0
00h
281
Si1000/1/2/3/4/5
The GPIO settings for GPIO1 and GPIO2 are the same as for GPIO0 with the exception of the 00000
default setting. The default settings for each GPIO are listed below:
GPIO
GPIO0
GPIO1
GPIO2
00000—Default Setting
POR
POR Inverted
Output Clock
For a complete list of the available GPIOs see “AN440: EZRadioPRO Detailed Register Descriptions”.
The GPIO drive strength may be adjusted with the gpioXdrv[1:0] bits. Setting a higher value will increase
the drive strength and current capability of the GPIO by changing the driver size. Special care should be
taken in setting the drive strength and loading on GPIO2 when the microcontroller clock is used. Excess
loading or inadequate drive may contribute to increased spurious emissions.
Pin 6, ANT_A may be used as an alternate to control a TR switch. Pin 6 is a hardwired version of GPIO
setting 11000, Antenna 2 Switch used for antenna diversity. It can be manually controlled by the antdiv[2:0]
bits in register 08h if antenna diversity is not used. See AN440, register 08h for more details.
23.8.9. Antenna Diversity
To mitigate the problem of frequency-selective fading due to multi-path propagation, some transceiver systems use a scheme known as antenna diversity. In this scheme, two antennas are used. Each time the
transceiver enters RX mode the receive signal strength from each antenna is evaluated. This evaluation
process takes place during the preamble portion of the packet. The antenna with the strongest received
signal is then used for the remainder of that RX packet. The same antenna will also be used for the next
corresponding TX packet.
This chip fully supports antenna diversity with an integrated antenna diversity control algorithm. The
required signals needed to control an external SPDT RF switch (such as PIN diode or GaAs switch) are
available on the GPIOx pins. The operation of these GPIO signals is programmable to allow for different
antenna diversity architectures and configurations. The antdiv[2:0] bits are found in register 08h “Operating
& Function Control 2.” The GPIO pins are capable of sourcing up to 5 mA of current, so it may be used
directly to forward-bias a PIN diode if desired.
The antenna diversity algorithm will automatically toggle back and forth between the antennas until the
packet starts to arrive. The recommended preamble length for optimal antenna selection is 8 bytes. A special antenna diversity algorithm (antdiv[2:0] = 110 or 111) is included that allows for shorter preamble
lengths for beacon mode in TDMA-like systems where the arrival of the packet is synchronous to the
receiver enable. The recommended preamble length to obtain optimal antenna selection for synchronous
mode is 4 bytes.
Add R/W Function/Description
08
282
R/W
Operating & Function
Control 2
D7
D6
D5
D4
antdiv[2] antdiv[1] antdiv[0] rxmpk
Rev. 1.3
D3
D2
D1
autotx enldm ffclrrx
D0
POR
Def.
ffclrtx
00h
Si1000/1/2/3/4/5
Table 23.8. Antenna Diversity Control
antdiv[2:0]
000
001
010
011
100
101
110
111
RX/TX State
GPIO Ant1
GPIO Ant2
0
1
1
0
0
1
1
0
Antenna Diversity Algorithm
Antenna Diversity Algorithm
Antenna Diversity Algorithm in Beacon Mode
Antenna Diversity Algorithm in Beacon Mode
Non RX/TX State
GPIO Ant1
GPIO Ant2
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
23.8.10. RSSI and Clear Channel Assessment
Received signal strength indicator (RSSI) is an estimate of the signal strength in the channel to which the
receiver is tuned. The RSSI value can be read from an 8-bit register with 0.5 dB resolution per bit.
Figure 23.25 demonstrates the relationship between input power level and RSSI value. The absolute value
of the RSSI will change slightly depending on the modem settings. The RSSI may be read at anytime, but
an incorrect error may rarely occur. The RSSI value may be incorrect if read during the update period. The
update period is approximately 10 ns every 4 Tb. For 10 kbps, this would result in a 1 in 40,000 probability
that the RSSI may be read incorrectly. This probability is extremely low, but to avoid this, one of the following options is recommended: majority polling, reading the RSSI value within 1 Tb of the RSSI interrupt, or
using the RSSI threshold described in the next paragraph for Clear Channel Assessment (CCA).
Add R/W
Function/Description
D7
D6
D5
D4
D3
D2
D1
D0
POR
Def.
26
R
Received Signal Strength Indicator
rssi[7]
rssi[6]
rssi[5]
rssi[4]
rssi[3]
rssi[2]
rssi[1]
rssi[0]
—
27
R/W
RSSI Threshold for Clear Channel Indicator
rssith[7]
rssith[6]
rssith[5]
rssith[4]
rssith[3]
rssith[2]
rssith[1]
rssith[0]
00h
For CCA, threshold is programmed into rssith[7:0] in "Register 27h. RSSI Threshold for Clear Channel
Indicator." After the RSSI is evaluated in the preamble, a decision is made if the signal strength on this
channel is above or below the threshold. If the signal strength is above the programmed threshold then the
RSSI status bit, irssi, in "Register 04h. Interrupt/Status 2" will be set to 1. The RSSI status can also be
routed to a GPIO line by configuring the GPIO configuration register to GPIOx[3:0] = 1110.
Rev. 1.3
283
Si1000/1/2/3/4/5
RSSI vs Input Power
250
200
RSSI
150
100
50
0
-120
-100
-80
-60
-40
-20
In Pow [dBm]
Figure 23.25. RSSI Value vs. Input Power
284
Rev. 1.3
0
20
&&
&0
&0
/0
/0
&0
Q)
X)
/
S)
&
/5
/5
&5
&
S)
&
/&
&5
4
7677=$
0+]
6'1
9''B5)
7;
5;3
5;1
1&
$17B$
8
6,
;7$/
3
3&'
567&&.
9''B0&8
*1'B0&8
395()
X)
&
R
Q)
&
7,7/(
SILICON LABS
S)
&
9''B5)
S)
&
Q)
&
9''B0&8
SILICON LABORATORIE
4
N+]
2SWLRQDO
Figure 23.26. Si1002 Split RF TX/RX Direct-Tie Reference Design—Schematic
434 33 33 8.2
3
100 3.9 51 3.6 36 6.2 16 N.F. 270
Refer to "AN436:
Si4030/4031/4430/4431
PA Matching" for
868 15 15 4.3 2.2
24 4.3 24 4.7 12 3.3 0 Ohm N.F. 68
component values.
CM LM CM2 LM2 CM3 CC1
[nH] [pF] [nH] [pF] [nH] [pF] [nH] [pF] [pF]
L0
[MHz] [nH] [nH] [pF] [pF]
C0
LC
Freq.
RX Side
band LR LR2 CR1 CR2
Si1002 Direct tie matching
&RPSRQHQWYDOXHVVKRXOGEHPRGLILHGEDVHGRQIUHTXHQF\EDQG
75;
2KPORDG
&
(3B5)
(3B0&8
&
1&
;,1
;287
1,54
3
3
3
3
3
3
3
3
3
;7$/
1&
*1'B5)
*3,2
*3,2
*3,2
95B',*
9''B',*
35()
3&19675
35;
37;
3;7$/
3;7$/
3$*1'
Rev. 1.3
9''B5)
Si1000/1/2/3/4/5
23.9. Reference Design
Reference designs are available at www.silabs.com for many common applications which include recommended schematics, BOM, and layout. TX matching component values for the different frequency bands
can be found in the application notes “AN435: Si4032/4432 PA Matching” and “AN436:
Si4030/4031/4430/4431 PA Matching.” RX matching component values for different frequency bands can
be found in “AN427: EZRadioPRO Si433x and Si443x RX LNA Matching.”
285
Rev. 1.3
&0
&&
&0
/0
8
6-
6-
83*7%
9& 287
5)B,1 *1'
9& 287
&0
&&
*3,2
*3,2
/
&5
S)
&
5+
&+
&
S)
&
/5
/+
47
33
27
11
11
5.6
4.7
4.7
3.9
3.3
15
10
12
6.8
6.8
390
270
270
120
120
150
120
100
39
33
18
11
10
5.6
5.6
15
12
11
6.0
5.6
50
50
50
50
50
33
24
22
15
12
10
6.8
5.6
3.3
3.0
33
24
22
15
12
390
270
220
68
56
15
8.2
9.1
4.7
4.3
24
18
15
9.1
8.2
15
8.2
9.1
4.7
4.3
&5
4
7677=$
0+]
6'1
9''B5)
7;
5;3
5;1
1&
$17B$
8
6,
Q)
S)
X)
R
&
&
S)
&
Q)
&
9''B0&8
Figure 23.27. Si1000 Switch Matching Reference Design—Schematic
SILICON LABORATORIES
4
N+]
2SWLRQDO
;7$/
3
3&'
567&&.
9''B0&8
*1'B0&8
395()
&
9''B5)
Refer to "AN427: EZRadioPRO™ Si433X & Si443X RX LNA Matching" and
SILICON LABS
"AN435: Si4032/4432 PA Matching" for component values.
315
434
470
868
915
Si1000 Switch matching
RX Side
Freq.
band LR CR1 CR2 LC C0 LH CH RH L0 CM LM CC1, CC2 CM2 LM2 CM3
[MHz] [nH] [pF] [pF] [nH] [pF] [nH] [pF] [Ohm] [nH] [pF] [nH]
[pF]
[pF] [nH] [pF]
/&
&RPSRQHQWYDOXHVVKRXOGEHPRGLILHGEDVHGRQIUHTXHQF\EDQG
75;
2KPORDG
Q)
X)
/0
&
(3B5)
(3B0&8
&
1&
;,1
;287
1,54
3
3
3
3
3
3
3
3
3
;7$/
1&
*1'B5)
*3,2
*3,2
*3,2
95B',*
9''B',*
35()
3&19675
35;
37;
3;7$/
3;7$/
3$*1'
286
9''B5)
Si1000/1/2/3/4/5
Si1000/1/2/3/4/5
23.10. Application Notes and Reference Designs
A comprehensive set of application notes and reference designs are available to assist with the development of a radio system. A partial list of applications notes is given below.
For the complete list of application notes, latest reference designs and demos visit the Silicon Labs website.























AN361: Wireless MBUS Implementation using EZRadioPRO Devices
AN379: Antenna Diversity with EZRadioPRO
AN414: EZRadioPRO Layout Design Guide
AN415: EZRadioPRO Programming Guide
AN417: Si4x3x Family Crystal Oscillators
AN419: ARIB STD-T67 Narrow-Band 426/429 MHz Measured on the Si4431-A0
AN427: EZRadioPRO Si433x and Si443x RX LNA Matching
AN429: Using the DC-DC Converter on the F9xx Series MCU for Single Battery Operation with the
EZRadioPRO RF Devices
AN432: RX BER Measurement on EZRadioPRO with a Looped PN Sequence
AN435: Si4032/4432 PA Matching
AN436: Si4030/4031/4430/4431 PA Matching
AN437: 915 MHz Measurement Results and FCC Compliance
AN439: EZRadioPRO Quick Start Guide
AN440: Si4430/31/32 Register Descriptions
AN445: Si4431 RF Performance and ETSI Compliance Test Results
AN451: Wireless M-BUS Software Implementation
AN459: 950 MHz Measurement Results and ARIB Compliance
AN460: 470 MHz Measurement Results for China
AN463: Support for Non-Standard Packet Structures and RAW Mode
AN466: Si4030/31/32 Register Descriptions
AN467: Si4330 Register Descriptions
AN514: Using the EZLink Reference Design to Create a Two-Channel PWM Motor Control Circuit
AN539: EZMacPRO Overview
23.11. Customer Support
Technical support for the complete family of Silicon Labs wireless products is available by accessing the
wireless section of the Silicon Labs' website at www.silabs.com/wireless. For MCU support, please visit
www.silabs.com/mcu.

For answers to common questions please visit the wireless and mcu knowledge base at
www.silabs.com/support/knowledgebase.
Rev. 1.3
287
Si1000/1/2/3/4/5
23.12. Register Table and Descriptions
Table 23.9. EZRadioPRO Internal Register Descriptions*
Add
R/W
Function/Desc
Data
POR
Default
D7
D6
D5
D4
D3
D2
D1
D0
00
R
Device Type
0
0
0
dt[4]
dt[3]
dt[2]
dt[1]
dt[0]
01000
01
R
Device Version
0
0
0
vc[4]
vc[3]
vc[2]
vc[1]
vc[0]
07h
02
R
Device Status
ffovfl
ffunfl
rxffem
headerr
reserved
reserved
cps[1]
cps[0]
—
—
03
R
Interrupt Status 1
ifferr
itxffafull
itxffaem
irxffafull
iext
ipksent
ipkvalid
icrcerror
04
R
Interrupt Status 2
iswdet
ipreaval
ipreainval
irssi
iwut
ilbd
ichiprdy
ipor
—
05
R/W
Interrupt Enable 1
enfferr
entxffafull
entxffaem
enrxffafull
enext
enpksent
enpkvalid
encrcerror
00h
06
R/W
Interrupt Enable 2
enswdet
enpreaval
enpreainval
enrssi
enwut
enlbd
enchiprdy
enpor
03h
07
R/W
Operating & Function Control 1
swres
enlbd
enwt
x32ksel
txon
rxon
pllon
xton
01h
08
R/W
Operating & Function Control 2
antdiv[2]
antdiv[1]
antdiv[0]
rxmpk
autotx
enldm
ffclrrx
ffclrtx
00h
09
R/W
Crystal Oscillator Load
Capacitance
xtalshft
xlc[6]
xlc[5]
xlc[4]
xlc[3]
xlc[2]
xlc[1]
xlc[0]
7Fh
0A
R/W Microcontroller Output Clock
Reserved
Reserved
clkt[1]
clkt[0]
enlfc
mclk[2]
mclk[1]
mclk[0]
06h
0B
R/W
GPIO0 Configuration
gpio0drv[1]
gpio0drv[0]
pup0
gpio0[4]
gpio0[3]
gpio0[2]
gpio0[1]
gpio0[0]
00h
0C
R/W
GPIO1 Configuration
gpio1drv[1]
gpio1drv[0]
pup1
gpio1[4]
gpio1[3]
gpio1[2]
gpio1[1]
gpio1[0]
00h
0D
R/W
GPIO2 Configuration
gpio2drv[1]
gpio2drv[0]
pup2
gpio2[4]
gpio2[3]
gpio2[2]
gpio2[1]
gpio2[0]
00h
0E
R/W
I/O Port Configuration
Reserved
extitst[2]
extitst[1]
extitst[0]
itsdo
dio2
dio1
dio0
00h
0F
R/W
ADC Configuration
adcstart/adcdone
adcsel[2]
adcsel[1]
adcsel[0]
adcref[1]
adcref[0]
adcgain[1]
adcgain[0]
00h
10
R/W ADC Sensor Amplifier Offset
Reserved
Reserved
Reserved
Reserved
adcoffs[3]
adcoffs[2]
adcoffs[1]
adcoffs[0]
00h
adc[7]
adc[6]
adc[5]
adc[4]
adc[3]
adc[2]
adc[1]
adc[0]
—
tsrange[1]
tsrange[0]
entsoffs
entstrim
tstrim[3]
tstrim[2]
tstrim[1]
tstrim[0]
20h
11
12
R
ADC Value
R/W Temperature Sensor Control
13
R/W
Temperature Value Offset
tvoffs[7]
tvoffs[6]
tvoffs[5]
tvoffs[4]
tvoffs[3]
tvoffs[2]
tvoffs[1]
tvoffs[0]
00h
14
R/W
Wake-Up Timer Period 1
Reserved
Reserved
Reserved
wtr[4]
wtr[3]
wtr[2]
wtr[1]
wtr[0]
03h
15
R/W
Wake-Up Timer Period 2
wtm[15]
wtm[14]
wtm[13]
wtm[12]
wtm[11]
wtm[10]
wtm[9]
wtm[8]
00h
16
R/W
Wake-Up Timer Period 3
wtm[7]
wtm[6]
wtm[5]
wtm[4]
wtm[3]
wtm[2]
wtm[1]
wtm[0]
01h
17
R
Wake-Up Timer Value 1
wtv[15]
wtv[14]
wtv[13]
wtv[12]
wtv[11]
wtv[10]
wtv[9]
wtv[8]
—
18
R
Wake-Up Timer Value 2
wtv[7]
wtv[6]
wtv[5]
wtv[4]
wtv[3]
wtv[2]
wtv[1]
wtv[0]
—
ldc[7]
ldc[6]
ldc[5]
ldc[4]
ldc[3]
ldc[2]
ldc[1]
ldc[0]
00h
Reserved
Reserved
Reserved
lbdt[4]
lbdt[3]
lbdt[2]
lbdt[1]
lbdt[0]
14h
19
R/W Low-Duty Cycle Mode Duration
1A
R/W
Low Battery Detector
Threshold
1B
R
Battery Voltage Level
0
0
0
vbat[4]
vbat[3]
vbat[2]
vbat[1]
vbat[0]
—
1C
R/W
IF Filter Bandwidth
dwn3_bypass
ndec[2]
ndec[1]
ndec[0]
filset[3]
filset[2]
filset[1]
filset[0]
01h
1D
R/W
AFC Loop Gearshift Override
afcbd
enafc
afcgearh[2]
afcgearh[1]
afcgearh[0]
1p5 bypass
matap
ph0size
40h
1E
R/W
AFC Timing Control
swait_timer[1]
swait_timer[0]
shwait[2]
shwait[1]
shwait[0]
anwait[2]
anwait[1]
anwait[0]
0Ah
1F
R/W
Clock Recovery
Gearshift Override
Reserved
Reserved
crfast[2]
crfast[1]
crfast[0]
crslow[2]
crslow[1]
crslow[0]
03h
20
R/W
Clock Recovery
Oversampling Ratio
rxosr[7]
rxosr[6]
rxosr[5]
rxosr[4]
rxosr[3]
rxosr[2]
rxosr[1]
rxosr[0]
64h
21
R/W
Clock Recovery
Offset 2
rxosr[10]
rxosr[9]
rxosr[8]
stallctrl
ncoff[19]
ncoff[18]
ncoff[17]
ncoff[16]
01h
22
R/W
Clock Recovery
Offset 1
ncoff[15]
ncoff[14]
ncoff[13]
ncoff[12]
ncoff[11]
ncoff[10]
ncoff[9]
ncoff[8]
47h
*Note: Detailed register descriptions are available in “AN440: Si4430/31/32 Register Descriptions”.
288
Rev. 1.3
Si1000/1/2/3/4/5
Table 23.9. EZRadioPRO Internal Register Descriptions* (Continued)
Add
R/W
Function/Desc
Data
D7
D6
D5
D4
D3
D2
D1
D0
POR
Default
23
R/W
Clock Recovery
Offset 0
ncoff[7]
ncoff[6]
ncoff[5]
ncoff[4]
ncoff[3]
ncoff[2]
ncoff[1]
ncoff[0]
AEh
24
R/W
Clock Recovery
Timing Loop Gain 1
Reserved
Reserved
Reserved
rxncocomp
crgain2x
crgain[10]
crgain[9]
crgain[8]
02h
25
R/W
Clock Recovery
Timing Loop Gain 0
crgain[7]
crgain[6]
crgain[5]
crgain[4]
crgain[3]
crgain[2]
crgain[1]
crgain[0]
8Fh
26
R
Received Signal Strength
Indicator
rssi[7]
rssi[6]
rssi[5]
rssi[4]
rssi[3]
rssi[2]
rssi[1]
rssi[0]
—
27
R/W
RSSI Threshold for Clear
Channel
Indicator
rssith[7]
rssith[6]
rssith[5]
rssith[4]
rssith[3]
rssith[2]
rssith[1]
rssith[0]
1Eh
28
R
Antenna Diversity Register 1
adrssi1[7]
adrssia[6]
adrssia[5]
adrssia[4]
adrssia[3]
adrssia[2]
adrssia[1]
adrssia[0]
—
29
R
Antenna Diversity Register 2
adrssib[7]
adrssib[6]
adrssib[5]
adrssib[4]
adrssib[3]
adrssib[2]
adrssib[1]
adrssib[0]
—
2A
R/W
AFC Limiter
Afclim[7]
Afclim[6]
Afclim[5]
Afclim[4]
Afclim[3]
Afclim[2]
Afclim[1]
Afclim[0]
00h
2B
R
AFC Correction Read
afc_corr[9]
afc_corr[8]
afc_corr[7]
afc_corr[6]
afc_corr[5]
afc_corr[4]
afc_corr[3]
afc_corr[2]
00h
2C
R/W
OOK Counter Value 1
afc_corr[9]
afc_corr[9]
ookfrzen
peakdeten
madeten
ookcnt[10]
ookcnt[9]
ookcnt[8]
18h
2D
R/W
OOK Counter Value 2
ookcnt[7]
ookcnt[6]
ookcnt[5]
ookcnt[4]
ookcnt[3]
ookcnt[2]
ookcnt[1]
ookcnt[0]
BCh
2E
R/W
Slicer Peak Hold
Reserved
attack[2]
attack[1]
attack[0]
decay[3]
decay[2]
decay[1]
decay[0]
26h
30
R/W
Data Access Control
enpacrx
lsbfrst
crcdonly
skip2ph
enpactx
encrc
crc[1]
crc[0]
8Dh
31
R
EzMAC status
0
rxcrc1
pksrch
pkrx
pkvalid
crcerror
pktx
pksent
32
R/W
Header Control 1
33
R/W
Header Control 2
skipsyn
hdlen[2]
hdlen[1]
hdlen[0]
fixpklen
synclen[1]
synclen[0]
prealen[8]
22h
34
R/W
Preamble Length
prealen[7]
prealen[6]
prealen[5]
prealen[4]
prealen[3]
prealen[2]
prealen[1]
prealen[0]
08h
35
R/W Preamble Detection Control
preath[4]
preath[3]
preath[2]
preath[1]
preath[0]
rssi_off[2]
rssi_off[1]
rssi_off[0]
2Ah
36
R/W
Sync Word 3
sync[31]
sync[30]
sync[29]
sync[28]
sync[27]
sync[26]
sync[25]
sync[24]
2Dh
37
R/W
Sync Word 2
sync[23]
sync[22]
sync[21]
sync[20]
sync[19]
sync[18]
sync[17]
sync[16]
D4h
38
R/W
Sync Word 1
sync[15]
sync[14]
sync[13]
sync[12]
sync[11]
sync[10]
sync[9]
sync[8]
00h
39
R/W
Sync Word 0
sync[7]
sync[6]
sync[5]
sync[4]
sync[3]
sync[2]
sync[1]
sync[0]
00h
3A
R/W
Transmit Header 3
txhd[31]
txhd[30]
txhd[29]
txhd[28]
txhd[27]
txhd[26]
txhd[25]
txhd[24]
00h
3B
R/W
Transmit Header 2
txhd[23]
txhd[22]
txhd[21]
txhd[20]
txhd[19]
txhd[18]
txhd[17]
txhd[16]
00h
3C
R/W
Transmit Header 1
txhd[15]
txhd[14]
txhd[13]
txhd[12]
txhd[11]
txhd[10]
txhd[9]
txhd[8]
00h
2F
Reserved
bcen[3:0]
hdch[3:0]
—
0Ch
3D
R/W
Transmit Header 0
txhd[7]
txhd[6]
txhd[5]
txhd[4]
txhd[3]
txhd[2]
txhd[1]
txhd[0]
00h
3E
R/W
Transmit Packet Length
pklen[7]
pklen[6]
pklen[5]
pklen[4]
pklen[3]
pklen[2]
pklen[1]
pklen[0]
00h
3F
R/W
Check Header 3
chhd[31]
chhd[30]
chhd[29]
chhd[28]
chhd[27]
chhd[26]
chhd[25]
chhd[24]
00h
40
R/W
Check Header 2
chhd[23]
chhd[22]
chhd[21]
chhd[20]
chhd[19]
chhd[18]
chhd[17]
chhd[16]
00h
41
R/W
Check Header 1
chhd[15]
chhd[14]
chhd[13]
chhd[12]
chhd[11]
chhd[10]
chhd[9]
chhd[8]
00h
42
R/W
Check Header 0
chhd[7]
chhd[6]
chhd[5]
chhd[4]
chhd[3]
chhd[2]
chhd[1]
chhd[0]
00h
43
R/W
Header Enable 3
hden[31]
hden[30]
hden[29]
hden[28]
hden[27]
hden[26]
hden[25]
hden[24]
FFh
44
R/W
Header Enable 2
hden[23]
hden[22]
hden[21]
hden[20]
hden[19]
hden[18]
hden[17]
hden[16]
FFh
45
R/W
Header Enable 1
hden[15]
hden[14]
hden[13]
hden[12]
hden[11]
hden[10]
hden[9]
hden[8]
FFh
46
R/W
Header Enable 0
hden[7]
hden[6]
hden[5]
hden[4]
hden[3]
hden[2]
hden[1]
hden[0]
FFh
47
R
Received Header 3
rxhd[31]
rxhd[30]
rxhd[29]
rxhd[28]
rxhd[27]
rxhd[26]
rxhd[25]
rxhd[24]
—
48
R
Received Header 2
rxhd[23]
rxhd[22]
rxhd[21]
rxhd[20]
rxhd[19]
rxhd[18]
rxhd[17]
rxhd[16]
—
49
R
Received Header 1
rxhd[15]
rxhd[14]
rxhd[13]
rxhd[12]
rxhd[11]
rxhd[10]
rxhd[9]
rxhd[8]
—
4A
R
Received Header 0
rxhd[7]
rxhd[6]
rxhd[5]
rxhd[4]
rxhd[3]
rxhd[2]
rxhd[1]
rxhd[0]
—
*Note: Detailed register descriptions are available in “AN440: Si4430/31/32 Register Descriptions”.
Rev. 1.3
289
Si1000/1/2/3/4/5
Table 23.9. EZRadioPRO Internal Register Descriptions* (Continued)
Add
4B
R/W
R
Function/Desc
Received Packet Length
Data
D6
D5
D4
D3
D2
D1
D0
rxplen[7]
rxplen[6]
rxplen[5]
rxplen[4]
rxplen[3]
rxplen[2]
rxplen[1]
rxplen[0]
—
adc8[4]
adc8[3]
adc8[2]
adc8[1]
adc8[0]
10h
chfiladd[3]
chfiladd[2]
chfiladd[1]
chfiladd[0]
00h
enbias2x
enamp2x
bufovr
enbuf
24h
4C-4E
4F
Reserved
R/W
ADC8 Control
Reserved
Reserved
50-5F
60
adc8[5]
Reserved
R/W
Channel Filter Coefficient
Address
Inv_pre_th[3]
R/W
Crystal Oscillator/
Control Test
pwst[2]
Inv_pre_th[2] Inv_pre_th[1] Inv_pre_th[0]
61
62
POR
Default
D7
Reserved
pwst[1]
63-6C
pwst[0]
clkhyst
Reserved
6D
R/W
TX Power
Reserved
Reserved
Reserved
Reserved
Ina_sw
txpow[2]
txpow[1]
txpow[0]
18h
6E
R/W
TX Data Rate 1
txdr[15]
txdr[14]
txdr[13]
txdr[12]
txdr[11]
txdr[10]
txdr[9]
txdr[8]
0Ah
6F
R/W
TX Data Rate 0
txdr[7]
txdr[6]
txdr[5]
txdr[4]
txdr[3]
txdr[2]
txdr[1]
txdr[0]
3Dh
70
R/W
Modulation Mode Control 1
Reserved
Reserved
txdtrtscale
enphpwdn
manppol
enmaninv
enmanch
enwhite
0Ch
71
R/W
Modulation Mode Control 2
trclk[1]
trclk[0]
dtmod[1]
dtmod[0]
eninv
fd[8]
modtyp[1]
modtyp[0]
00h
72
R/W
Frequency Deviation
fd[7]
fd[6]
fd[5]
fd[4]
fd[3]
fd[2]
fd[1]
fd[0]
20h
73
R/W
Frequency Offset 1
fo[7]
fo[6]
fo[5]
fo[4]
fo[3]
fo[2]
fo[1]
fo[0]
00h
74
R/W
Frequency Offset 2
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
fo[9]
fo[8]
00h
75
R/W
Frequency Band Select
Reserved
sbsel
hbsel
fb[4]
fb[3]
fb[2]
fb[1]
fb[0]
75h
76
R/W
Nominal Carrier Frequency
1
fc[15]
fc[14]
fc[13]
fc[12]
fc[11]
fc[10]
fc[9]
fc[8]
BBh
77
R/W
Nominal Carrier Frequency
0
fc[7]
fc[6]
fc[5]
fc[4]
fc[3]
fc[2]
fc[1]
fc[0]
80h
78
Reserved
79
R/W
Frequency Hopping
Channel Select
fhch[7]
fhch[6]
fhch[5]
fhch[4]
fhch[3]
fhch[2]
fhch[1]
fhch[0]
00h
7A
R/W
Frequency Hopping
Step Size
fhs[7]
fhs[6]
fhs[5]
fhs[4]
fhs[3]
fhs[2]
fhs[1]
fhs[0]
00h
R/W
TX FIFO Control 1
Reserved
Reserved
txafthr[5]
txafthr[4]
txafthr[3]
txafthr[2]
txafthr[1]
txafthr[0]
37h
7D
R/W
TX FIFO Control 2
Reserved
Reserved
txaethr[5]
txaethr[4]
txaethr[3]
txaethr[2]
txaethr[1]
txaethr[0]
04h
7E
R/W
RX FIFO Control
Reserved
Reserved
rxafthr[5]
rxafthr[4]
rxafthr[3]
rxafthr[2]
rxafthr[1]
rxafthr[0]
37h
7F
R/W
FIFO Access
fifod[7]
fifod[6]
fifod[5]
fifod[4]
fifod[3]
fifod[2]
fifod[1]
fifod[0]
—
7B
7C
Reserved
*Note: Detailed register descriptions are available in “AN440: Si4430/31/32 Register Descriptions”.
23.13. Required Changes to Default Register Values
The following register writes should be performed during device initialization.
Register modifications are required for operation in the frequency bands between 240–320 MHz and 480–
640 MHz with a temperature above 60 °C. In these cases, write 03h to register 59h and 02h to register
5Ah.
290
Rev. 1.3
Si1000/1/2/3/4/5
24. SMBus
The SMBus I/O interface is a two-wire, bi-directional serial bus. The SMBus is compliant with the System
Management Bus Specification, version 1.1, and compatible with the I2C serial bus. Reads and writes to
the interface by the system controller are byte oriented with the SMBus interface autonomously controlling
the serial transfer of the data. Data can be transferred at up to 1/20th of the system clock as a master or
slave (this can be faster than allowed by the SMBus specification, depending on the system clock used). A
method of extending the clock-low duration is available to accommodate devices with different speed
capabilities on the same bus.
The SMBus interface may operate as a master and/or slave, and may function on a bus with multiple masters. The SMBus provides control of SDA (serial data), SCL (serial clock) generation and synchronization,
arbitration logic, and START/STOP control and generation. The SMBus peripheral can be fully driven by
software (i.e., software accepts/rejects slave addresses, and generates ACKs), or hardware slave address
recognition and automatic ACK generation can be enabled to minimize software overhead. A block diagram of the SMBus peripheral and the associated SFRs is shown in Figure 24.1.
SMB0CN
M T S S A A A S
A X T T CR C I
SMAOK B K
T O
R L
E D
QO
R E
S
T
SMB0CF
E I B E S S S S
N N U XMMMM
S H S T B B B B
M Y H T F CC
B
OO T S S
L E E 1 0
D
SMBUS CONTROL LOGIC
Arbitration
SCL Synchronization
SCL Generation (Master Mode)
SDA Control
Hardware Slave Address Recognition
Hardware ACK Generation
Data Path
IRQ Generation
Control
Interrupt
Request
00
T0 Overflow
01
T1 Overflow
10
TMR2H Overflow
11
TMR2L Overflow
SCL
Control
S
L
V
5
S
L
V
4
S
L
V
3
S
L
V
2
S
L
V
1
SMB0ADR
SG
L C
V
0
S S S S S S S
L L L L L L L
V V V V V V V
MMMMMMM
6 5 4 3 2 1 0
SMB0ADM
C
R
O
S
S
B
A
R
N
SDA
Control
SMB0DAT
7 6 5 4 3 2 1 0
S
L
V
6
SCL
FILTER
Port I/O
SDA
FILTER
E
H
A
C
K
N
Figure 24.1. SMBus Block Diagram
Rev. 1.3
291
Si1000/1/2/3/4/5
24.1. Supporting Documents
It is assumed the reader is familiar with or has access to the following supporting documents:
1. The I2C-Bus and How to Use It (including specifications), Philips Semiconductor.
2. The I2C-Bus Specification—Version 2.0, Philips Semiconductor.
3. System Management Bus Specification—Version 1.1, SBS Implementers Forum.
24.2. SMBus Configuration
Figure 24.2 shows a typical SMBus configuration. The SMBus specification allows any recessive voltage
between 3.0 V and 5.0 V; different devices on the bus may operate at different voltage levels. The bi-directional SCL (serial clock) and SDA (serial data) lines must be connected to a positive power supply voltage
through a pullup resistor or similar circuit. Every device connected to the bus must have an open-drain or
open-collector output for both the SCL and SDA lines, so that both are pulled high (recessive state) when
the bus is free. The maximum number of devices on the bus is limited only by the requirement that the rise
and fall times on the bus not exceed 300 ns and 1000 ns, respectively.
VDD = 5V
VDD = 3V
VDD = 5V
VDD = 3V
Master
Device
Slave
Device 1
Slave
Device 2
SDA
SCL
Figure 24.2. Typical SMBus Configuration
24.3. SMBus Operation
Two types of data transfers are possible: data transfers from a master transmitter to an addressed slave
receiver (WRITE), and data transfers from an addressed slave transmitter to a master receiver (READ).
The master device initiates both types of data transfers and provides the serial clock pulses on SCL. The
SMBus interface may operate as a master or a slave, and multiple master devices on the same bus are
supported. If two or more masters attempt to initiate a data transfer simultaneously, an arbitration scheme
is employed with a single master always winning the arbitration. Note that it is not necessary to specify one
device as the Master in a system; any device who transmits a START and a slave address becomes the
master for the duration of that transfer.
A typical SMBus transaction consists of a START condition followed by an address byte (Bits7–1: 7-bit
slave address; Bit0: R/W direction bit), one or more bytes of data, and a STOP condition. Bytes that are
received (by a master or slave) are acknowledged (ACK) with a low SDA during a high SCL (see
Figure 24.3). If the receiving device does not ACK, the transmitting device will read a NACK (not acknowledge), which is a high SDA during a high SCL.
The direction bit (R/W) occupies the least-significant bit position of the address byte. The direction bit is set
to logic 1 to indicate a "READ" operation and cleared to logic 0 to indicate a "WRITE" operation.
292
Rev. 1.3
Si1000/1/2/3/4/5
All transactions are initiated by a master, with one or more addressed slave devices as the target. The
master generates the START condition and then transmits the slave address and direction bit. If the transaction is a WRITE operation from the master to the slave, the master transmits the data a byte at a time
waiting for an ACK from the slave at the end of each byte. For READ operations, the slave transmits the
data waiting for an ACK from the master at the end of each byte. At the end of the data transfer, the master
generates a STOP condition to terminate the transaction and free the bus. Figure 24.3 illustrates a typical
SMBus transaction.
SCL
SDA
SLA6
START
SLA5-0
Slave Address + R/W
R/W
D7
ACK
D6-0
Data Byte
NACK
STOP
Figure 24.3. SMBus Transaction
24.3.1. Transmitter vs. Receiver
On the SMBus communications interface, a device is the “transmitter” when it is sending an address or
data byte to another device on the bus. A device is a “receiver” when an address or data byte is being sent
to it from another device on the bus. The transmitter controls the SDA line during the address or data byte.
After each byte of address or data information is sent by the transmitter, the receiver sends an ACK or
NACK bit during the ACK phase of the transfer, during which time the receiver controls the SDA line.
24.3.2. Arbitration
A master may start a transfer only if the bus is free. The bus is free after a STOP condition or after the SCL
and SDA lines remain high for a specified time (see Section “24.3.5. SCL High (SMBus Free) Timeout” on
page 294). In the event that two or more devices attempt to begin a transfer at the same time, an arbitration scheme is employed to force one master to give up the bus. The master devices continue transmitting
until one attempts a HIGH while the other transmits a LOW. Since the bus is open-drain, the bus will be
pulled LOW. The master attempting the HIGH will detect a LOW SDA and lose the arbitration. The winning
master continues its transmission without interruption; the losing master becomes a slave and receives the
rest of the transfer if addressed. This arbitration scheme is non-destructive: one device always wins, and
no data is lost.
24.3.3. Clock Low Extension
SMBus provides a clock synchronization mechanism, similar to I2C, which allows devices with different
speed capabilities to coexist on the bus. A clock-low extension is used during a transfer in order to allow
slower slave devices to communicate with faster masters. The slave may temporarily hold the SCL line
LOW to extend the clock low period, effectively decreasing the serial clock frequency.
Rev. 1.3
293
Si1000/1/2/3/4/5
24.3.4. SCL Low Timeout
If the SCL line is held low by a slave device on the bus, no further communication is possible. Furthermore,
the master cannot force the SCL line high to correct the error condition. To solve this problem, the SMBus
protocol specifies that devices participating in a transfer must detect any clock cycle held low longer than
25 ms as a “timeout” condition. Devices that have detected the timeout condition must reset the communication no later than 10 ms after detecting the timeout condition.
When the SMBTOE bit in SMB0CF is set, Timer 3 is used to detect SCL low timeouts. Timer 3 is forced to
reload when SCL is high, and allowed to count when SCL is low. With Timer 3 enabled and configured to
overflow after 25 ms (and SMBTOE set), the Timer 3 interrupt service routine can be used to reset (disable
and re-enable) the SMBus in the event of an SCL low timeout.
24.3.5. SCL High (SMBus Free) Timeout
The SMBus specification stipulates that if the SCL and SDA lines remain high for more that 50 µs, the bus
is designated as free. When the SMBFTE bit in SMB0CF is set, the bus will be considered free if SCL and
SDA remain high for more than 10 SMBus clock source periods (as defined by the timer configured for the
SMBus clock source). If the SMBus is waiting to generate a Master START, the START will be generated
following this timeout. Note that a clock source is required for free timeout detection, even in a slave-only
implementation.
24.4. Using the SMBus
The SMBus can operate in both Master and Slave modes. The interface provides timing and shifting control for serial transfers; higher level protocol is determined by user software. The SMBus interface provides
the following application-independent features:
Byte-wise serial data transfers
Clock signal generation on SCL (Master Mode only) and SDA data synchronization
 Timeout/bus error recognition, as defined by the SMB0CF configuration register
 START/STOP timing, detection, and generation
 Bus arbitration
 Interrupt generation
 Status information
 Optional hardware recognition of slave address and automatic acknowledgement of address/data
SMBus interrupts are generated for each data byte or slave address that is transferred. When hardware
acknowledgement is disabled, the point at which the interrupt is generated depends on whether the hardware is acting as a data transmitter or receiver. When a transmitter (i.e. sending address/data, receiving an
ACK), this interrupt is generated after the ACK cycle so that software may read the received ACK value;
when receiving data (i.e. receiving address/data, sending an ACK), this interrupt is generated before the
ACK cycle so that software may define the outgoing ACK value. If hardware acknowledgement is enabled,
these interrupts are always generated after the ACK cycle. See Section 24.5 for more details on transmission sequences.


Interrupts are also generated to indicate the beginning of a transfer when a master (START generated), or
the end of a transfer when a slave (STOP detected). Software should read the SMB0CN (SMBus Control
register) to find the cause of the SMBus interrupt. The SMB0CN register is described in Section 24.4.2;
Table 24.5 provides a quick SMB0CN decoding reference.
294
Rev. 1.3
Si1000/1/2/3/4/5
24.4.1. SMBus Configuration Register
The SMBus Configuration register (SMB0CF) is used to enable the SMBus Master and/or Slave modes,
select the SMBus clock source, and select the SMBus timing and timeout options. When the ENSMB bit is
set, the SMBus is enabled for all master and slave events. Slave events may be disabled by setting the
INH bit. With slave events inhibited, the SMBus interface will still monitor the SCL and SDA pins; however,
the interface will NACK all received addresses and will not generate any slave interrupts. When the INH bit
is set, all slave events will be inhibited following the next START (interrupts will continue for the duration of
the current transfer).
Table 24.1. SMBus Clock Source Selection
SMBCS1
SMBCS0
SMBus Clock Source
0
0
1
1
0
1
0
1
Timer 0 Overflow
Timer 1 Overflow
Timer 2 High Byte Overflow
Timer 2 Low Byte Overflow
The SMBCS1–0 bits select the SMBus clock source, which is used only when operating as a master or
when the Free Timeout detection is enabled. When operating as a master, overflows from the selected
source determine the absolute minimum SCL low and high times as defined in Equation 24.1. Note that the
selected clock source may be shared by other peripherals so long as the timer is left running at all times.
For example, Timer 1 overflows may generate the SMBus and UART baud rates simultaneously. Timer
configuration is covered in Section “27. Timers” on page 335.
1
T HighMin = T LowMin = ---------------------------------------------f ClockSourceOverflow
Equation 24.1. Minimum SCL High and Low Times
The selected clock source should be configured to establish the minimum SCL High and Low times as per
Equation 24.1. When the interface is operating as a master (and SCL is not driven or extended by any
other devices on the bus), the typical SMBus bit rate is approximated by Equation 24.2.
f ClockSourceOverflow
BitRate = ---------------------------------------------3
Equation 24.2. Typical SMBus Bit Rate
Figure 24.4 shows the typical SCL generation described by Equation 24.2. Notice that THIGH is typically
twice as large as TLOW. The actual SCL output may vary due to other devices on the bus (SCL may be
extended low by slower slave devices, or driven low by contending master devices). The bit rate when
operating as a master will never exceed the limits defined by equation Equation 24.1.
Timer Source
Overflows
SCL
TLow
SCL High Timeout
THigh
Figure 24.4. Typical SMBus SCL Generation
Rev. 1.3
295
Si1000/1/2/3/4/5
Setting the EXTHOLD bit extends the minimum setup and hold times for the SDA line. The minimum SDA
setup time defines the absolute minimum time that SDA is stable before SCL transitions from low-to-high.
The minimum SDA hold time defines the absolute minimum time that the current SDA value remains stable
after SCL transitions from high-to-low. EXTHOLD should be set so that the minimum setup and hold times
meet the SMBus Specification requirements of 250 ns and 300 ns, respectively. Table 24.2 shows the minimum setup and hold times for the two EXTHOLD settings. Setup and hold time extensions are typically
necessary when SYSCLK is above 10 MHz.
Table 24.2. Minimum SDA Setup and Hold Times
EXTHOLD
0
1
Minimum SDA Setup Time
Tlow – 4 system clocks
or
1 system clock + s/w delay*
11 system clocks
Minimum SDA Hold Time
3 system clocks
12 system clocks
Note: Setup Time for ACK bit transmissions and the MSB of all data transfers. When using
software acknowledgement, the s/w delay occurs between the time SMB0DAT or
ACK is written and when SI is cleared. Note that if SI is cleared in the same write
that defines the outgoing ACK value, s/w delay is zero.
With the SMBTOE bit set, Timer 3 should be configured to overflow after 25 ms in order to detect SCL low
timeouts (see Section “24.3.4. SCL Low Timeout” on page 294). The SMBus interface will force Timer 3 to
reload while SCL is high, and allow Timer 3 to count when SCL is low. The Timer 3 interrupt service routine
should be used to reset SMBus communication by disabling and re-enabling the SMBus.
SMBus Free Timeout detection can be enabled by setting the SMBFTE bit. When this bit is set, the bus will
be considered free if SDA and SCL remain high for more than 10 SMBus clock source periods (see
Figure 24.4).
296
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 24.1. SMB0CF: SMBus Clock/Configuration
Bit
7
6
5
4
Name
ENSMB
INH
BUSY
Type
R/W
R/W
R
R/W
Reset
0
0
0
0
EXTHOLD SMBTOE
SFR Page = 0x0; SFR Address = 0xC1
Bit
Name
7
ENSMB
3
2
1
0
SMBFTE
SMBCS[1:0]
R/W
R/W
R/W
0
0
0
0
Function
SMBus Enable.
This bit enables the SMBus interface when set to 1. When enabled, the interface
constantly monitors the SDA and SCL pins.
6
INH
SMBus Slave Inhibit.
When this bit is set to logic 1, the SMBus does not generate an interrupt when slave
events occur. This effectively removes the SMBus slave from the bus. Master Mode
interrupts are not affected.
5
BUSY
SMBus Busy Indicator.
This bit is set to logic 1 by hardware when a transfer is in progress. It is cleared to
logic 0 when a STOP or free-timeout is sensed.
4
EXTHOLD
SMBus Setup and Hold Time Extension Enable.
This bit controls the SDA setup and hold times according to Table 24.2.
0: SDA Extended Setup and Hold Times disabled.
1: SDA Extended Setup and Hold Times enabled.
3
SMBTOE
SMBus SCL Timeout Detection Enable.
This bit enables SCL low timeout detection. If set to logic 1, the SMBus forces
Timer 3 to reload while SCL is high and allows Timer 3 to count when SCL goes low.
If Timer 3 is configured to Split Mode, only the High Byte of the timer is held in reload
while SCL is high. Timer 3 should be programmed to generate interrupts at 25 ms,
and the Timer 3 interrupt service routine should reset SMBus communication.
2
SMBFTE
SMBus Free Timeout Detection Enable.
When this bit is set to logic 1, the bus will be considered free if SCL and SDA remain
high for more than 10 SMBus clock source periods.
1 :0
SMBCS[1:0] SMBus Clock Source Selection.
These two bits select the SMBus clock source, which is used to generate the SMBus
bit rate. The selected device should be configured according to Equation 24.1.
00: Timer 0 Overflow
01: Timer 1 Overflow
10:Timer 2 High Byte Overflow
11: Timer 2 Low Byte Overflow
Rev. 1.3
297
Si1000/1/2/3/4/5
24.4.2. SMB0CN Control Register
SMB0CN is used to control the interface and to provide status information (see SFR Definition 24.2). The
higher four bits of SMB0CN (MASTER, TXMODE, STA, and STO) form a status vector that can be used to
jump to service routines. MASTER indicates whether a device is the master or slave during the current
transfer. TXMODE indicates whether the device is transmitting or receiving data for the current byte.
STA and STO indicate that a START and/or STOP has been detected or generated since the last SMBus
interrupt. STA and STO are also used to generate START and STOP conditions when operating as a master. Writing a 1 to STA will cause the SMBus interface to enter Master Mode and generate a START when
the bus becomes free (STA is not cleared by hardware after the START is generated). Writing a 1 to STO
while in Master Mode will cause the interface to generate a STOP and end the current transfer after the
next ACK cycle. If STO and STA are both set (while in Master Mode), a STOP followed by a START will be
generated.
The ARBLOST bit indicates that the interface has lost an arbitration. This may occur anytime the interface
is transmitting (master or slave). A lost arbitration while operating as a slave indicates a bus error condition. ARBLOST is cleared by hardware each time SI is cleared.
The SI bit (SMBus Interrupt Flag) is set at the beginning and end of each transfer, after each byte frame, or
when an arbitration is lost; see Table 24.3 for more details.
Important Note About the SI Bit: The SMBus interface is stalled while SI is set; thus SCL is held low, and
the bus is stalled until software clears SI.
24.4.2.1. Software ACK Generation
When the EHACK bit in register SMB0ADM is cleared to 0, the firmware on the device must detect incoming slave addresses and ACK or NACK the slave address and incoming data bytes. As a receiver, writing
the ACK bit defines the outgoing ACK value; as a transmitter, reading the ACK bit indicates the value
received during the last ACK cycle. ACKRQ is set each time a byte is received, indicating that an outgoing
ACK value is needed. When ACKRQ is set, software should write the desired outgoing value to the ACK
bit before clearing SI. A NACK will be generated if software does not write the ACK bit before clearing SI.
SDA will reflect the defined ACK value immediately following a write to the ACK bit; however SCL will
remain low until SI is cleared. If a received slave address is not acknowledged, further slave events will be
ignored until the next START is detected.
24.4.2.2. Hardware ACK Generation
When the EHACK bit in register SMB0ADM is set to 1, automatic slave address recognition and ACK generation is enabled. More detail about automatic slave address recognition can be found in Section 24.4.3.
As a receiver, the value currently specified by the ACK bit will be automatically sent on the bus during the
ACK cycle of an incoming data byte. As a transmitter, reading the ACK bit indicates the value received on
the last ACK cycle. The ACKRQ bit is not used when hardware ACK generation is enabled. If a received
slave address is NACKed by hardware, further slave events will be ignored until the next START is
detected, and no interrupt will be generated.
Table 24.3 lists all sources for hardware changes to the SMB0CN bits. Refer to Table 24.5 for SMBus status decoding using the SMB0CN register.
Refer to “Limitations for Hardware Acknowledge Feature” on page 303 when using hardware ACK generation.
298
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 24.2. SMB0CN: SMBus Control
Bit
7
6
5
4
3
2
1
0
Name
MASTER
TXMODE
STA
STO
ACKRQ
ARBLOST
ACK
SI
Type
R
R
R/W
R/W
R
R
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xC0; Bit-Addressable
Bit
Name
Description
Read
Write
7
MASTER SMBus Master/Slave
Indicator. This read-only bit
indicates when the SMBus is
operating as a master.
0: SMBus operating in
slave mode.
1: SMBus operating in
master mode.
N/A
6
TXMODE SMBus Transmit Mode
Indicator. This read-only bit
indicates when the SMBus is
operating as a transmitter.
0: SMBus in Receiver
Mode.
1: SMBus in Transmitter
Mode.
N/A
5
STA
SMBus Start Flag.
0: No Start or repeated
Start detected.
1: Start or repeated Start
detected.
0: No Start generated.
1: When Configured as a
Master, initiates a START
or repeated START.
4
STO
SMBus Stop Flag.
0: No Stop condition
detected.
1: Stop condition detected
(if in Slave Mode) or pending (if in Master Mode).
0: No STOP condition is
transmitted.
1: When configured as a
Master, causes a STOP
condition to be transmitted after the next ACK
cycle.
Cleared by Hardware.
3
ACKRQ
SMBus Acknowledge
Request.
0: No Ack requested
1: ACK requested
N/A
0: No arbitration error.
1: Arbitration Lost
N/A
2
ARBLOST SMBus Arbitration Lost
Indicator.
1
ACK
SMBus Acknowledge.
0: NACK received.
1: ACK received.
0: Send NACK
1: Send ACK
0
SI
SMBus Interrupt Flag.
0: No interrupt pending
0: Clear interrupt, and initiate next state machine
event.
1: Force interrupt.
This bit is set by hardware
1: Interrupt Pending
under the conditions listed in
Table 15.3. SI must be cleared
by software. While SI is set,
SCL is held low and the
SMBus is stalled.
Rev. 1.3
299
Si1000/1/2/3/4/5
Table 24.3. Sources for Hardware Changes to SMB0CN
Bit
Set by Hardware When:
MASTER

TXMODE

Cleared by Hardware When:
A START is generated.

A STOP is generated.
Arbitration is lost.
A START is detected.
Arbitration is lost.
SMB0DAT is not written before the
start of an SMBus frame.
Must be cleared by software.

A pending STOP is generated.

After each ACK cycle.

Each time SI is cleared.


START is generated.
 SMB0DAT is written before the start of an
SMBus frame.
STA

STO


ACKRQ

ARBLOST



ACK

SI






300
A START followed by an address byte is
received.
A STOP is detected while addressed as a
slave.
Arbitration is lost due to a detected STOP.
A byte has been received and an ACK
response value is needed (only when
hardware ACK is not enabled).
A repeated START is detected as a
MASTER when STA is low (unwanted
repeated START).
SCL is sensed low while attempting to
generate a STOP or repeated START
condition.
SDA is sensed low while transmitting a 1
(excluding ACK bits).
The incoming ACK value is low 
(ACKNOWLEDGE).
A START has been generated.
Lost arbitration.
A byte has been transmitted and an
ACK/NACK received.
A byte has been received.
A START or repeated START followed by a
slave address + R/W has been received.
A STOP has been received.
Rev. 1.3



The incoming ACK value is high
(NOT ACKNOWLEDGE).
 Must be cleared by software.

Si1000/1/2/3/4/5
24.4.3. Hardware Slave Address Recognition
The SMBus hardware has the capability to automatically recognize incoming slave addresses and send an
ACK without software intervention. Automatic slave address recognition is enabled by setting the EHACK
bit in register SMB0ADM to 1. This will enable both automatic slave address recognition and automatic
hardware ACK generation for received bytes (as a master or slave). More detail on automatic hardware
ACK generation can be found in Section 24.4.2.2.
The registers used to define which address(es) are recognized by the hardware are the SMBus Slave
Address register (SFR Definition 24.3) and the SMBus Slave Address Mask register (SFR Definition 24.4).
A single address or range of addresses (including the General Call Address 0x00) can be specified using
these two registers. The most-significant seven bits of the two registers are used to define which
addresses will be ACKed. A 1 in bit positions of the slave address mask SLVM[6:0] enable a comparison
between the received slave address and the hardware’s slave address SLV[6:0] for those bits. A 0 in a bit
of the slave address mask means that bit will be treated as a “don’t care” for comparison purposes. In this
case, either a 1 or a 0 value are acceptable on the incoming slave address. Additionally, if the GC bit in
register SMB0ADR is set to 1, hardware will recognize the General Call Address (0x00). Table 24.4 shows
some example parameter settings and the slave addresses that will be recognized by hardware under
those conditions. Refer to “Limitations for Hardware Acknowledge Feature” on page 303 when using hardware slave address recognition.
Table 24.4. Hardware Address Recognition Examples (EHACK = 1)
Hardware Slave Address
SLV[6:0]
Slave Address Mask
SLVM[6:0]
GC bit
Slave Addresses Recognized by
Hardware
0x34
0x34
0x34
0x34
0x70
0x7F
0x7F
0x7E
0x7E
0x73
0
1
0
1
0
0x34
0x34, 0x00 (General Call)
0x34, 0x35
0x34, 0x35, 0x00 (General Call)
0x70, 0x74, 0x78, 0x7C
Rev. 1.3
301
Si1000/1/2/3/4/5
SFR Definition 24.3. SMB0ADR: SMBus Slave Address
Bit
7
6
5
4
3
2
1
0
Name
SLV[6:0]
GC
Type
R/W
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xF4
Bit
Name
7 :1
SLV[6:0]
0
0
0
0
Function
SMBus Hardware Slave Address.
Defines the SMBus Slave Address(es) for automatic hardware acknowledgement.
Only address bits which have a 1 in the corresponding bit position in SLVM[6:0]
are checked against the incoming address. This allows multiple addresses to be
recognized.
0
GC
General Call Address Enable.
When hardware address recognition is enabled (EHACK = 1), this bit will determine whether the General Call Address (0x00) is also recognized by hardware.
0: General Call Address is ignored.
1: General Call Address is recognized.
SFR Definition 24.4. SMB0ADM: SMBus Slave Address Mask
Bit
7
6
5
4
3
2
1
0
Name
SLVM[6:0]
EHACK
Type
R/W
R/W
Reset
1
1
1
1
SFR Page = 0x0; SFR Address = 0xF5
Bit
Name
7 :1
SLVM[6:0]
1
1
1
0
Function
SMBus Slave Address Mask.
Defines which bits of register SMB0ADR are compared with an incoming address
byte, and which bits are ignored. Any bit set to 1 in SLVM[6:0] enables comparisons with the corresponding bit in SLV[6:0]. Bits set to 0 are ignored (can be either
0 or 1 in the incoming address).
0
EHACK
Hardware Acknowledge Enable.
Enables hardware acknowledgement of slave address and received data bytes.
0: Firmware must manually acknowledge all incoming address and data bytes.
1: Automatic Slave Address Recognition and Hardware Acknowledge is Enabled.
302
Rev. 1.3
Si1000/1/2/3/4/5
24.4.4. Limitations for Hardware Acknowledge Feature
In some system management bus (SMBus) configurations, the Hardware Acknowledge mechanism of the
SMBus peripheral can cause incorrect or undesired behavior. The Hardware Acknowledge mechanism is
enabled when the EHACK bit (SMB0ADM.0) is set to logic 1.
The configurations to which these limitations do not apply are as follows:
a. All SMBus configurations when Hardware Acknowledge is disabled.
b. All single-master/single-slave SMBus configurations when Hardware Acknowledge is enabled
and the MCU is operating as a master or slave.
c. All multi-master/single-slave SMBus configurations when Hardware Acknowledge is enabled
and the MCU is operating as a slave.
d. All single-master/multi-slave SMBus configurations when Hardware Acknowledge is enabled
and the MCU is operating as a master.
These limitations only apply to the following configurations:
a. All multi-slave SMBus configurations when Hardware Acknowledge is enabled and the MCU is
operating as a slave.
b. All multi-master SMBus configurations when Hardware Acknowledge is enabled and the MCU
is operating as a master.
The following issues are present when operating as a slave in a multi-slave SMBus configuration:
a. When Hardware Acknowledge is enabled and SDA setup and hold times are not extended
(EXTHOLD = 0 in the SMB0CF register), the SMBus hardware will always generate an SMBus
interrupt following the ACK/NACK cycle of any slave address transmission on the bus, whether
or not the address matches the conditions of SMB0ADR and SMB0MASK. The expected
behavior is that an interrupt is only generated when the address matches.
b. When Hardware Acknowledge is enabled and SDA setup and hold times are extended 
(EXTHOLD = 1 in the SMB0CF register), the SMBus hardware will only generate an SMBus
interrupt as expected when the slave address transmission on the bus matches the conditions of
SMB0ADR and SMB0MASK. However, in this mode, the Start bit (STA) will be incorrectly
cleared on reception of a slave address before software vectors to the interrupt service routine.
c. When Hardware Acknowledge is enabled and the ACK bit (SMB0CN.1) is set to 1, an
unaddressed slave may cause interference on the SMBus by driving SDA low during an ACK
cycle. The ACK bit of the unaddressed slave may be set to 1 if any device on the bus generates
an ACK.
Impact:
a. Once the CPU enters the interrupt service routine, SCL will be asserted low until SI is cleared,
causing the clock to be stretched when the MCU is not being addressed. This may limit the
maximum speed of the SMBus if the master supports SCL clock stretching. Incompliant SMBus
masters that do not support SCL clock stretching will not recognize that the clock is being
stretched. If the CPU issues a write to SMB0DAT, it will have no effect on the bus. No data
collisions will occur.
b. Once the hardware has matched an address and entered the interrupt service routine, the
firmware will not be able to use the Start bit to distinguish between the reception of an address
byte versus the reception of a data byte. However, the hardware will still correctly acknowledge
the address byte (SLA+R/W).
c. The SMBus master and the addressed slave are prevented from generating a NACK by the
unaddressed slave because it is holding SDA low during the ACK cycle. There is a potential for
the SMBus to lock up.
Rev. 1.3
303
Si1000/1/2/3/4/5
Workarounds:
a. The SMBus interrupt service routine should verify an address when it is received and clear SI as
soon as possible if the address does not match to minimize clock stretching. To prevent clock
stretching when not being addressed, enable setup and hold time extensions (EXTHOLD = 1).
b. Detection of Initial Start:

To distinguish between the reception of an address byte at the beginning of a transfer versus
the reception of a data byte when setup and hold time extensions are enabled (EXTHOLD = 1),
software should maintain a status bit to determine whether it is currently inside or outside a
transfer. Once hardware detects a matching slave address and interrupts the MCU, software
should assume a start condition and set the software bit to indicate that it is currently inside a
transfer. A transfer ends any time the STO bit is set or on an error condition (e.g., SCL Low
Timeout). 

Detection of Repeated Start:

To detect the reception of an address byte in the middle of a transfer when setup and hold time
extensions are enabled (EXTHOLD = 1), disable setup and hold time extensions (EXTHOLD =
0) upon entry into a transfer and re-enable setup and hold time extensions (EXHOLD = 1) at the
end of a transfer.
c. Schedule a timer interrupt to clear the ACK bit at an interval shorter than 7 bit periods when the
slave is not being addressed. For example, on a 400 kHz SMBus, the ACK bit should be cleared
every 17.5 µs (or at 1/7 the bus frequency, 57 kHz). As soon as a matching slave address is
detected (a transfer is started), the timer which clears the ACK bit should be stopped and its
interrupt flag cleared. The timer should be re-started once a stop or error condition is detected
(the transfer has ended).
A code example demonstrating these workarounds can be found in the SMBus examples folder with the
following default location:
C:\SiLabs\MCU\Examples\C8051F93x_92x\SMBus\F93x_SMBus_Slave_Multibyte_HWACK.c
The SMBus examples folder, along with examples for many additional peripherals, is created when the Silicon Laboratories IDE is installed. The latest version of the IDE may be downloaded from the software
downloads page www.silabs.com/MCUDownloads on the Silicon Laboratories website.
The following issue is present when operating as a master in a multi-master SMBus configuration:
If the SMBus master loses arbitration in a multi-master system, it may cause interference on the SMBus by
driving SDA low during the ACK cycle of transfers which it is not participating. This will occur regardless of
the state of the ACK bit (SMB0CN.1).
Impact:
The SMBus master and slave participating in the transfer are prevented from generating a NACK by the
MCU because it is holding SDA low during the ACK cycle. There is a potential for the SMBus to lock up.
Workaround:
Disable Hardware Acknowledge (EHACK = 0) when the MCU is operating as a master in a multi-master
SMBus configuration.
304
Rev. 1.3
Si1000/1/2/3/4/5
24.4.5. Data Register
The SMBus Data register SMB0DAT holds a byte of serial data to be transmitted or one that has just been
received. Software may safely read or write to the data register when the SI flag is set. Software should not
attempt to access the SMB0DAT register when the SMBus is enabled and the SI flag is cleared to logic 0,
as the interface may be in the process of shifting a byte of data into or out of the register.
Data in SMB0DAT is always shifted out MSB first. After a byte has been received, the first bit of received
data is located at the MSB of SMB0DAT. While data is being shifted out, data on the bus is simultaneously
being shifted in. SMB0DAT always contains the last data byte present on the bus. In the event of lost arbitration, the transition from master transmitter to slave receiver is made with the correct data or address in
SMB0DAT.
SFR Definition 24.5. SMB0DAT: SMBus Data
Bit
7
6
5
4
3
Name
SMB0DAT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xC2
Bit
Name
0
2
1
0
0
0
0
Function
7:0 SMB0DAT[7:0] SMBus Data.
The SMB0DAT register contains a byte of data to be transmitted on the SMBus
serial interface or a byte that has just been received on the SMBus serial interface.
The CPU can read from or write to this register whenever the SI serial interrupt flag
(SMB0CN.0) is set to logic 1. The serial data in the register remains stable as long
as the SI flag is set. When the SI flag is not set, the system may be in the process
of shifting data in/out and the CPU should not attempt to access this register.
Rev. 1.3
305
Si1000/1/2/3/4/5
24.5. SMBus Transfer Modes
The SMBus interface may be configured to operate as master and/or slave. At any particular time, it will be
operating in one of the following four modes: Master Transmitter, Master Receiver, Slave Transmitter, or
Slave Receiver. The SMBus interface enters Master Mode any time a START is generated, and remains in
Master Mode until it loses an arbitration or generates a STOP. An SMBus interrupt is generated at the end
of all SMBus byte frames. Note that the position of the ACK interrupt when operating as a receiver
depends on whether hardware ACK generation is enabled. As a receiver, the interrupt for an ACK occurs
before the ACK with hardware ACK generation disabled, and after the ACK when hardware ACK generation is enabled. As a transmitter, interrupts occur after the ACK, regardless of whether hardware ACK generation is enabled or not.
24.5.1. Write Sequence (Master)
During a write sequence, an SMBus master writes data to a slave device. The master in this transfer will be
a transmitter during the address byte, and a transmitter during all data bytes. The SMBus interface generates the START condition and transmits the first byte containing the address of the target slave and the
data direction bit. In this case the data direction bit (R/W) will be logic 0 (WRITE). The master then transmits one or more bytes of serial data. After each byte is transmitted, an acknowledge bit is generated by
the slave. The transfer is ended when the STO bit is set and a STOP is generated. Note that the interface
will switch to Master Receiver Mode if SMB0DAT is not written following a Master Transmitter interrupt.
Figure 24.5 shows a typical master write sequence. Two transmit data bytes are shown, though any number of bytes may be transmitted. Notice that all of the ‘data byte transferred’ interrupts occur after the ACK
cycle in this mode, regardless of whether hardware ACK generation is enabled.
Interrupts with Hardware ACK Enabled (EHACK = 1)
S
SLA
W
A
Data Byte
A
Data Byte
A
P
Interrupts with Hardware ACK Disabled (EHACK = 0)
S = START
P = STOP
A = ACK
W = WRITE
SLA = Slave Address
Received by SMBus
Interface
Transmitted by
SMBus Interface
Figure 24.5. Typical Master Write Sequence
24.5.2. Read Sequence (Master)
During a read sequence, an SMBus master reads data from a slave device. The master in this transfer will
be a transmitter during the address byte, and a receiver during all data bytes. The SMBus interface generates the START condition and transmits the first byte containing the address of the target slave and the
data direction bit. In this case the data direction bit (R/W) will be logic 1 (READ). Serial data is then
received from the slave on SDA while the SMBus outputs the serial clock. The slave transmits one or more
bytes of serial data.
If hardware ACK generation is disabled, the ACKRQ is set to 1 and an interrupt is generated after each
received byte. Software must write the ACK bit at that time to ACK or NACK the received byte.
306
Rev. 1.3
Si1000/1/2/3/4/5
With hardware ACK generation enabled, the SMBus hardware will automatically generate the ACK/NACK,
and then post the interrupt. It is important to note that the appropriate ACK or NACK value should be
set up by the software prior to receiving the byte when hardware ACK generation is enabled.
Writing a 1 to the ACK bit generates an ACK; writing a 0 generates a NACK. Software should write a 0 to
the ACK bit for the last data transfer, to transmit a NACK. The interface exits Master Receiver Mode after
the STO bit is set and a STOP is generated. The interface will switch to Master Transmitter Mode if SMB0DAT is written while an active Master Receiver. Figure 24.6 shows a typical master read sequence. Two
received data bytes are shown, though any number of bytes may be received. Notice that the ‘data byte
transferred’ interrupts occur at different places in the sequence, depending on whether hardware ACK generation is enabled. The interrupt occurs before the ACK with hardware ACK generation disabled, and after
the ACK when hardware ACK generation is enabled.
Interrupts with Hardware ACK Enabled (EHACK = 1)
S
SLA
R
A
Data Byte
A
Data Byte
N
P
Interrupts with Hardware ACK Disabled (EHACK = 0)
S = START
P = STOP
A = ACK
N = NACK
R = READ
SLA = Slave Address
Received by SMBus
Interface
Transmitted by
SMBus Interface
Figure 24.6. Typical Master Read Sequence
24.5.3. Write Sequence (Slave)
During a write sequence, an SMBus master writes data to a slave device. The slave in this transfer will be
a receiver during the address byte, and a receiver during all data bytes. When slave events are enabled
(INH = 0), the interface enters Slave Receiver Mode when a START followed by a slave address and direction bit (WRITE in this case) is received. If hardware ACK generation is disabled, upon entering Slave
Receiver Mode, an interrupt is generated and the ACKRQ bit is set. The software must respond to the
received slave address with an ACK, or ignore the received slave address with a NACK. If hardware ACK
generation is enabled, the hardware will apply the ACK for a slave address which matches the criteria set
up by SMB0ADR and SMB0ADM. The interrupt will occur after the ACK cycle.
If the received slave address is ignored (by software or hardware), slave interrupts will be inhibited until the
next START is detected. If the received slave address is acknowledged, zero or more data bytes are
received.
If hardware ACK generation is disabled, the ACKRQ is set to 1 and an interrupt is generated after each
received byte. Software must write the ACK bit at that time to ACK or NACK the received byte.
With hardware ACK generation enabled, the SMBus hardware will automatically generate the ACK/NACK,
and then post the interrupt. It is important to note that the appropriate ACK or NACK value should be
set up by the software prior to receiving the byte when hardware ACK generation is enabled.
The interface exits Slave Receiver Mode after receiving a STOP. Note that the interface will switch to Slave
Transmitter Mode if SMB0DAT is written while an active Slave Receiver. Figure 24.7 shows a typical slave
write sequence. Two received data bytes are shown, though any number of bytes may be received. Notice
Rev. 1.3
307
Si1000/1/2/3/4/5
that the “data byte transferred” interrupts occur at different places in the sequence, depending on whether
hardware ACK generation is enabled. The interrupt occurs before the ACK with hardware ACK generation
disabled, and after the ACK when hardware ACK generation is enabled.
Interrupts with Hardware ACK Enabled (EHACK = 1)
S
SLA
W
A
Data Byte
A
Data Byte
A
P
Interrupts with Hardware ACK Disabled (EHACK = 0)
S = START
P = STOP
A = ACK
W = WRITE
SLA = Slave Address
Received by SMBus
Interface
Transmitted by
SMBus Interface
Figure 24.7. Typical Slave Write Sequence
24.5.4. Read Sequence (Slave)
During a read sequence, an SMBus master reads data from a slave device. The slave in this transfer will
be a receiver during the address byte, and a transmitter during all data bytes. When slave events are
enabled (INH = 0), the interface enters Slave Receiver Mode (to receive the slave address) when a START
followed by a slave address and direction bit (READ in this case) is received. If hardware ACK generation
is disabled, upon entering Slave Receiver Mode, an interrupt is generated and the ACKRQ bit is set. The
software must respond to the received slave address with an ACK, or ignore the received slave address
with a NACK. If hardware ACK generation is enabled, the hardware will apply the ACK for a slave address
which matches the criteria set up by SMB0ADR and SMB0ADM. The interrupt will occur after the ACK
cycle.
If the received slave address is ignored (by software or hardware), slave interrupts will be inhibited until the
next START is detected. If the received slave address is acknowledged, zero or more data bytes are transmitted. If the received slave address is acknowledged, data should be written to SMB0DAT to be transmitted. The interface enters Slave Transmitter Mode, and transmits one or more bytes of data. After each byte
is transmitted, the master sends an acknowledge bit; if the acknowledge bit is an ACK, SMB0DAT should
be written with the next data byte. If the acknowledge bit is a NACK, SMB0DAT should not be written to
before SI is cleared (Note: an error condition may be generated if SMB0DAT is written following a received
NACK while in Slave Transmitter Mode). The interface exits Slave Transmitter Mode after receiving a
STOP. Note that the interface will switch to Slave Receiver Mode if SMB0DAT is not written following a
Slave Transmitter interrupt. Figure 24.8 shows a typical slave read sequence. Two transmitted data bytes
are shown, though any number of bytes may be transmitted. Notice that all of the ‘data byte transferred’
interrupts occur after the ACK cycle in this mode, regardless of whether hardware ACK generation is
enabled.
308
Rev. 1.3
Si1000/1/2/3/4/5
Interrupts with Hardware ACK Enabled (EHACK = 1)
S
SLA
R
A
Data Byte
A
Data Byte
N
P
Interrupts with Hardware ACK Disabled (EHACK = 0)
S = START
P = STOP
N = NACK
R = READ
SLA = Slave Address
Received by SMBus
Interface
Transmitted by
SMBus Interface
Figure 24.8. Typical Slave Read Sequence
24.6. SMBus Status Decoding
The current SMBus status can be easily decoded using the SMB0CN register. The appropriate actions to
take in response to an SMBus event depend on whether hardware slave address recognition and ACK
generation is enabled or disabled. Table 24.5 describes the typical actions when hardware slave address
recognition and ACK generation is disabled. Table 24.6 describes the typical actions when hardware slave
address recognition and ACK generation is enabled. In the tables, STATUS VECTOR refers to the four
upper bits of SMB0CN: MASTER, TXMODE, STA, and STO. The shown response options are only the typical responses; application-specific procedures are allowed as long as they conform to the SMBus specification. Highlighted responses are allowed by hardware but do not conform to the SMBus specification.
Rev. 1.3
309
Si1000/1/2/3/4/5
STO
ACK
Load slave address + R/W into
SMB0DAT.
0
0
X 1100
1
0
X 1110
0
1
X -
A master data or address byte Load next data byte into SMB0- 0
was transmitted; ACK
DAT.
received.
End transfer with STOP.
0
0
X 1100
1
X -
End transfer with STOP and start 1
another transfer.
1
X -
Send repeated START.
1
0
X 1110
Switch to Master Receiver Mode 0
(clear SI without writing new data
to SMB0DAT).
0
X 1000
Acknowledge received byte;
Read SMB0DAT.
0
0
1
1000
Send NACK to indicate last byte, 0
and send STOP.
1
0
-
Send NACK to indicate last byte, 1
and send STOP followed by
START.
1
0
1110
Send ACK followed by repeated 1
START.
0
1
1110
Send NACK to indicate last byte, 1
and send repeated START.
0
0
1110
Send ACK and switch to Master 0
Transmitter Mode (write to
SMB0DAT before clearing SI).
0
1
1100
Send NACK and switch to Mas- 0
ter Transmitter Mode (write to
SMB0DAT before clearing SI).
0
0
1100
0
0
X A master START was generated.
1100
0
0
0
0
1
A master data or address byte Set STA to restart transfer.
was transmitted; NACK
Abort transfer.
received.
Master Transmitter
0
ACK
1110
Master Receiver
1000 1
310
0
X A master data byte was
received; ACK requested.
Rev. 1.3
Next Status
Vector Expected
Values to
Write
ARBLOST
Typical Response Options
ACKRQ
Current SMbus State
Status
Vector
Mode
Values Read
STA
Table 24.5. SMBus Status Decoding With Hardware ACK Generation Disabled (EHACK = 0)
Si1000/1/2/3/4/5
STO
ACK
0
A slave byte was transmitted; No action required (expecting
NACK received.
STOP condition).
0
0
X 0001
0
0
1
A slave byte was transmitted; Load SMB0DAT with next data
ACK received.
byte to transmit.
0
0
X 0100
0
1
X A Slave byte was transmitted; No action required (expecting
error detected.
Master to end transfer).
0
0
X 0001
ACKRQ
0
Status
Vector
STA
Values to
Write
ACK
Typical Response Options
0100 0
0101 0
X X An illegal STOP or bus error Clear STO.
was detected while a Slave
Transmission was in progress.
0
0
X -
0010 1
0
0
0
1
0000
If Read, Load SMB0DAT with
0
data byte; ACK received address
0
1
0100
NACK received address.
0
0
0
-
X Lost arbitration as master;
If Write, Acknowledge received 0
slave address + R/W received; address
ACK requested.
If Read, Load SMB0DAT with
0
data byte; ACK received address
0
1
0000
0
1
0100
1
Bus Error Condition Slave Receiver
Current SMbus State
ARBLOST
Slave Transmitter
Mode
Values Read
Next Status
Vector Expected
Table 24.5. SMBus Status Decoding With Hardware ACK Generation Disabled (EHACK = 0)
(Continued)
1
X A slave address + R/W was
received; ACK requested.
If Write, Acknowledge received
address
NACK received address.
0
0
0
-
Reschedule failed transfer;
NACK received address.
1
0
0
1110
Clear STO.
0
0
X -
0001 0
0
X A STOP was detected while
addressed as a Slave Transmitter or Slave Receiver.
1
1
X Lost arbitration while attempt- No action required (transfer
ing a STOP.
complete/aborted).
0
0
0
-
0000 1
0
X A slave byte was received;
ACK requested.
Acknowledge received byte;
Read SMB0DAT.
0
0
1
0000
NACK received byte.
0
0
0
-
0
0
X -
1
0
X 1110
Abort failed transfer.
0
0
X -
Reschedule failed transfer.
1
0
X 1110
X Lost arbitration while transmit- Abort failed transfer.
ting a data byte as master.
Reschedule failed transfer.
0
0
0
-
1
0
0
1110
0010 0
0001 0
0000 1
1
1
1
X Lost arbitration while attempt- Abort failed transfer.
ing a repeated START.
Reschedule failed transfer.
X Lost arbitration due to a
detected STOP.
Rev. 1.3
311
Si1000/1/2/3/4/5
STO
ACK
Load slave address + R/W into
SMB0DAT.
0
0
X 1100
1
0
X 1110
0
1
X -
A master data or address byte Load next data byte into SMB0- 0
was transmitted; ACK
DAT.
received.
End transfer with STOP.
0
0
X 1100
1
X -
End transfer with STOP and start 1
another transfer.
1
X -
Send repeated START.
1
0
X 1110
Switch to Master Receiver Mode 0
(clear SI without writing new data
to SMB0DAT). Set ACK for initial
data byte.
0
1
1000
Set ACK for next data byte;
Read SMB0DAT.
0
0
1
1000
Set NACK to indicate next data
byte as the last data byte;
Read SMB0DAT.
0
0
0
1000
Initiate repeated START.
1
0
0
1110
Switch to Master Transmitter
0
Mode (write to SMB0DAT before
clearing SI).
0
X 1100
Read SMB0DAT; send STOP.
0
1
0
-
Read SMB0DAT; Send STOP
followed by START.
1
1
0
1110
Initiate repeated START.
1
0
0
1110
Switch to Master Transmitter
0
Mode (write to SMB0DAT before
clearing SI).
0
X 1100
0
0
X A master START was generated.
1100
0
0
0
0
1
A master data or address byte Set STA to restart transfer.
was transmitted; NACK
Abort transfer.
received.
Master Transmitter
0
ACK
1110
1000 0
Master Receiver
0
312
0
0
1
0
A master data byte was
received; ACK sent.
A master data byte was
received; NACK sent (last
byte).
Rev. 1.3
Next Status
Vector Expected
Values to
Write
ARBLOST
Typical Response Options
ACKRQ
Current SMbus State
Status
Vector
Mode
Values Read
STA
Table 24.6. SMBus Status Decoding With Hardware ACK Generation Enabled (EHACK = 1)
Si1000/1/2/3/4/5
STO
ACK
0
A slave byte was transmitted; No action required (expecting
NACK received.
STOP condition).
0
0
X 0001
0
0
1
A slave byte was transmitted; Load SMB0DAT with next data
ACK received.
byte to transmit.
0
0
X 0100
0
1
X A Slave byte was transmitted; No action required (expecting
error detected.
Master to end transfer).
0
0
X 0001
ACKRQ
0
Status
Vector
STA
Values to
Write
ACK
Typical Response Options
0100 0
0101 0
X X An illegal STOP or bus error Clear STO.
was detected while a Slave
Transmission was in progress.
0
0
X -
0010 0
0
If Write, Set ACK for first data
byte.
0
0
1
If Read, Load SMB0DAT with
data byte
0
0
X 0100
X Lost arbitration as master;
If Write, Set ACK for first data
slave address + R/W received; byte.
ACK sent.
If Read, Load SMB0DAT with
data byte
0
0
1
0
0
X 0100
Reschedule failed transfer
1
0
X 1110
Clear STO.
0
0
X -
0
Bus Error Condition Slave Receiver
Current SMbus State
ARBLOST
Slave Transmitter
Mode
Values Read
Next Status
Vector Expected
Table 24.6. SMBus Status Decoding With Hardware ACK Generation Enabled (EHACK = 1)
(Continued)
1
X A slave address + R/W was
received; ACK sent.
0000
0000
0001 0
0
X A STOP was detected while
addressed as a Slave Transmitter or Slave Receiver.
0
1
X Lost arbitration while attempt- No action required (transfer
ing a STOP.
complete/aborted).
0
0
0
-
0000 0
0
X A slave byte was received.
Set ACK for next data byte;
Read SMB0DAT.
0
0
1
0000
Set NACK for next data byte;
Read SMB0DAT.
0
0
0
0000
0
0
X -
1
0
X 1110
Abort failed transfer.
0
0
X -
Reschedule failed transfer.
1
0
X 1110
X Lost arbitration while transmit- Abort failed transfer.
ting a data byte as master.
Reschedule failed transfer.
0
0
X -
1
0
X 1110
0010 0
0001 0
0000 0
1
1
1
X Lost arbitration while attempt- Abort failed transfer.
ing a repeated START.
Reschedule failed transfer.
X Lost arbitration due to a
detected STOP.
Rev. 1.3
313
Si1000/1/2/3/4/5
25. UART0
UART0 is an asynchronous, full duplex serial port offering modes 1 and 3 of the standard 8051 UART.
Enhanced baud rate support allows a wide range of clock sources to generate standard baud rates (details
in Section “25.1. Enhanced Baud Rate Generation” on page 315). Received data buffering allows UART0
to start reception of a second incoming data byte before software has finished reading the previous data
byte.
UART0 has two associated SFRs: Serial Control Register 0 (SCON0) and Serial Data Buffer 0 (SBUF0).
The single SBUF0 location provides access to both transmit and receive registers. Writes to SBUF0
always access the Transmit register. Reads of SBUF0 always access the buffered Receive register;
it is not possible to read data from the Transmit register.
With UART0 interrupts enabled, an interrupt is generated each time a transmit is completed (TI0 is set in
SCON0), or a data byte has been received (RI0 is set in SCON0). The UART0 interrupt flags are not
cleared by hardware when the CPU vectors to the interrupt service routine. They must be cleared manually
by software, allowing software to determine the cause of the UART0 interrupt (transmit complete or receive
complete).
SFR Bus
Write to
SBUF
TB8
SBUF
(TX Shift)
SET
D
Q
TX
CLR
Crossbar
Zero Detector
Stop Bit
Shift
Start
Data
Tx Control
Tx Clock
Send
Tx IRQ
TI
MCE
REN
TB8
RB8
TI
RI
SMODE
SCON
UART Baud
Rate Generator
RI
Serial
Port
Interrupt
Port I/O
Rx IRQ
Rx Clock
Rx Control
Start
Shift
0x1FF
RB8
Load
SBUF
Input Shift Register
(9 bits)
Load SBUF
SBUF
(RX Latch)
Read
SBUF
SFR Bus
RX
Crossbar
Figure 25.1. UART0 Block Diagram
314
Rev. 1.3
Si1000/1/2/3/4/5
25.1. Enhanced Baud Rate Generation
The UART0 baud rate is generated by Timer 1 in 8-bit auto-reload mode. The TX clock is generated by
TL1; the RX clock is generated by a copy of TL1 (shown as RX Timer in Figure 25.2), which is not useraccessible. Both TX and RX Timer overflows are divided by two to generate the TX and RX baud rates.
The RX Timer runs when Timer 1 is enabled, and uses the same reload value (TH1). However, an
RX Timer reload is forced when a START condition is detected on the RX pin. This allows a receive to
begin any time a START is detected, independent of the TX Timer state.
Timer 1
TL1
UART
Overflow
2
TX Clock
Overflow
2
RX Clock
TH1
Start
Detected
RX Timer
Figure 25.2. UART0 Baud Rate Logic
Timer 1 should be configured for Mode 2, 8-bit auto-reload (see Section “27.1.3. Mode 2: 8-bit
Counter/Timer with Auto-Reload” on page 338). The Timer 1 reload value should be set so that overflows
will occur at two times the desired UART baud rate frequency. Note that Timer 1 may be clocked by one of
six sources: SYSCLK, SYSCLK / 4, SYSCLK / 12, SYSCLK / 48, the external oscillator clock / 8, or an
external input T1. For any given Timer 1 clock source, the UART0 baud rate is determined by
Equation 25.1-A and Equation 25.1-B.
A)
1
UartBaudRate = ---  T1_Overflow_Rate
2
B)
T1 CLK
T1_Overflow_Rate = -------------------------256 – TH1
Equation 25.1. UART0 Baud Rate
Where T1CLK is the frequency of the clock supplied to Timer 1, and T1H is the high byte of Timer 1 (reload
value). Timer 1 clock frequency is selected as described in Section “27.1. Timer 0 and Timer 1” on
page 337. A quick reference for typical baud rates and system clock frequencies is given in Table 25.1
through Table 25.2. Note that the internal oscillator may still generate the system clock when the external
oscillator is driving Timer 1.
Rev. 1.3
315
Si1000/1/2/3/4/5
25.2. Operational Modes
UART0 provides standard asynchronous, full duplex communication. The UART mode (8-bit or 9-bit) is
selected by the S0MODE bit (SCON0.7). Typical UART connection options are shown below.
TX
RS-232
LEVEL
XLTR
RS-232
RX
C8051Fxxx
OR
TX
TX
RX
RX
MCU
C8051Fxxx
Figure 25.3. UART Interconnect Diagram
25.2.1. 8-Bit UART
8-Bit UART mode uses a total of 10 bits per data byte: one start bit, eight data bits (LSB first), and one stop
bit. Data are transmitted LSB first from the TX0 pin and received at the RX0 pin. On receive, the eight data
bits are stored in SBUF0 and the stop bit goes into RB80 (SCON0.2).
Data transmission begins when software writes a data byte to the SBUF0 register. The TI0 Transmit Interrupt Flag (SCON0.1) is set at the end of the transmission (the beginning of the stop-bit time). Data reception can begin any time after the REN0 Receive Enable bit (SCON0.4) is set to logic 1. After the stop bit is
received, the data byte will be loaded into the SBUF0 receive register if the following conditions are met:
RI0 must be logic 0, and if MCE0 is logic 1, the stop bit must be logic 1. In the event of a receive data overrun, the first received 8 bits are latched into the SBUF0 receive register and the following overrun data bits
are lost.
If these conditions are met, the eight bits of data is stored in SBUF0, the stop bit is stored in RB80 and the
RI0 flag is set. If these conditions are not met, SBUF0 and RB80 will not be loaded and the RI0 flag will not
be set. An interrupt will occur if enabled when either TI0 or RI0 is set.
MARK
SPACE
START
BIT
D0
D1
D2
D3
D4
D5
D6
BIT TIMES
BIT SAMPLING
Figure 25.4. 8-Bit UART Timing Diagram
316
Rev. 1.3
D7
STOP
BIT
Si1000/1/2/3/4/5
25.2.2. 9-Bit UART
9-bit UART mode uses a total of eleven bits per data byte: a start bit, 8 data bits (LSB first), a programmable ninth data bit, and a stop bit. The state of the ninth transmit data bit is determined by the value in TB80
(SCON0.3), which is assigned by user software. It can be assigned the value of the parity flag (bit P in register PSW) for error detection, or used in multiprocessor communications. On receive, the ninth data bit
goes into RB80 (SCON0.2) and the stop bit is ignored.
Data transmission begins when an instruction writes a data byte to the SBUF0 register. The TI0 Transmit
Interrupt Flag (SCON0.1) is set at the end of the transmission (the beginning of the stop-bit time). Data
reception can begin any time after the REN0 Receive Enable bit (SCON0.4) is set to 1. After the stop bit is
received, the data byte will be loaded into the SBUF0 receive register if the following conditions are met:
(1) RI0 must be logic 0, and (2) if MCE0 is logic 1, the 9th bit must be logic 1 (when MCE0 is logic 0, the
state of the ninth data bit is unimportant). If these conditions are met, the eight bits of data are stored in
SBUF0, the ninth bit is stored in RB80, and the RI0 flag is set to 1. If the above conditions are not met,
SBUF0 and RB80 will not be loaded and the RI0 flag will not be set to 1. A UART0 interrupt will occur if
enabled when either TI0 or RI0 is set to 1.
MARK
SPACE
START
BIT
D0
D1
D2
D3
D4
D5
D6
D7
D8
STOP
BIT
BIT TIMES
BIT SAMPLING
Figure 25.5. 9-Bit UART Timing Diagram
25.3. Multiprocessor Communications
9-Bit UART mode supports multiprocessor communication between a master processor and one or more
slave processors by special use of the ninth data bit. When a master processor wants to transmit to one or
more slaves, it first sends an address byte to select the target(s). An address byte differs from a data byte
in that its ninth bit is logic 1; in a data byte, the ninth bit is always set to logic 0.
Setting the MCE0 bit (SCON0.5) of a slave processor configures its UART such that when a stop bit is
received, the UART will generate an interrupt only if the ninth bit is logic 1 (RB80 = 1) signifying an address
byte has been received. In the UART interrupt handler, software will compare the received address with
the slave's own assigned 8-bit address. If the addresses match, the slave will clear its MCE0 bit to enable
interrupts on the reception of the following data byte(s). Slaves that weren't addressed leave their MCE0
bits set and do not generate interrupts on the reception of the following data bytes, thereby ignoring the
data. Once the entire message is received, the addressed slave resets its MCE0 bit to ignore all transmissions until it receives the next address byte.
Multiple addresses can be assigned to a single slave and/or a single address can be assigned to multiple
slaves, thereby enabling "broadcast" transmissions to more than one slave simultaneously. The master
processor can be configured to receive all transmissions or a protocol can be implemented such that the
master/slave role is temporarily reversed to enable half-duplex transmission between the original master
and slave(s).
Rev. 1.3
317
Si1000/1/2/3/4/5
Master
Device
RX
TX
Slave
Device
RX
TX
Slave
Device
RX
TX
Slave
Device
RX
TX
Figure 25.6. UART Multi-Processor Mode Interconnect Diagram
318
Rev. 1.3
V+
Si1000/1/2/3/4/5
SFR Definition 25.1. SCON0: Serial Port 0 Control
Bit
7
6
Name
S0MODE
Type
R/W
Reset
0
5
4
3
2
1
0
MCE0
REN0
TB80
RB80
TI0
RI0
R
R/W
R/W
R/W
R/W
R/W
R/W
1
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0x98; Bit-Addressable
Bit
7
Name
Function
S0MODE Serial Port 0 Operation Mode.
Selects the UART0 Operation Mode.
0: 8-bit UART with Variable Baud Rate.
1: 9-bit UART with Variable Baud Rate.
6
Unused
5
MCE0
Read = 1b. Write = Don’t Care.
Multiprocessor Communication Enable.
For Mode 0 (8-bit UART): Checks for valid stop bit.
0: Logic level of stop bit is ignored.
1: RI0 will only be activated if stop bit is logic level 1.
For Mode 1 (9-bit UART): Multiprocessor Communications Enable.
0: Logic level of ninth bit is ignored.
1: RI0 is set and an interrupt is generated only when the ninth bit is logic 1.
4
REN0
Receive Enable.
0: UART0 reception disabled.
1: UART0 reception enabled.
3
TB80
Ninth Transmission Bit.
The logic level of this bit will be sent as the ninth transmission bit in 9-bit UART Mode
(Mode 1). Unused in 8-bit mode (Mode 0).
2
RB80
Ninth Receive Bit.
RB80 is assigned the value of the STOP bit in Mode 0; it is assigned the value of the
9th data bit in Mode 1.
1
TI0
Transmit Interrupt Flag.
Set by hardware when a byte of data has been transmitted by UART0 (after the 8th bit
in 8-bit UART Mode, or at the beginning of the STOP bit in 9-bit UART Mode). When
the UART0 interrupt is enabled, setting this bit causes the CPU to vector to the UART0
interrupt service routine. This bit must be cleared manually by software.
0
RI0
Receive Interrupt Flag.
Set to 1 by hardware when a byte of data has been received by UART0 (set at the
STOP bit sampling time). When the UART0 interrupt is enabled, setting this bit to 1
causes the CPU to vector to the UART0 interrupt service routine. This bit must be
cleared manually by software.
Rev. 1.3
319
Si1000/1/2/3/4/5
SFR Definition 25.2. SBUF0: Serial (UART0) Port Data Buffer
Bit
7
6
5
4
3
2
1
0
SBUF0[7:0]
Name
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0x99
Bit
Name
7:0
SBUF0
Function
Serial Data Buffer Bits 7:0 (MSB–LSB)
This SFR accesses two registers; a transmit shift register and a receive latch register.
When data is written to SBUF0, it goes to the transmit shift register and is held for
serial transmission. Writing a byte to SBUF0 initiates the transmission. A read of
SBUF0 returns the contents of the receive latch.
320
Rev. 1.3
Si1000/1/2/3/4/5
Table 25.1. Timer Settings for Standard Baud Rates
Using The Internal 24.5 MHz Oscillator
Frequency: 24.5 MHz
SYSCLK from
Internal Osc.
Target
Baud Rate
(bps)
230400
115200
57600
28800
14400
9600
2400
1200
Baud Rate
% Error
–0.32%
–0.32%
0.15%
–0.32%
0.15%
–0.32%
–0.32%
0.15%
Timer Clock
Oscillator Source
Divide
Factor
106
212
426
848
1704
2544
10176
20448
SCA1–SCA0
(pre-scale
select)1
SYSCLK
SYSCLK
SYSCLK
SYSCLK/4
SYSCLK/12
SYSCLK/12
SYSCLK/48
SYSCLK/48
XX2
XX
XX
01
00
00
10
10
T1M1 Timer 1
Reload
Value (hex)
1
1
1
0
0
0
0
0
0xCB
0x96
0x2B
0x96
0xB9
0x96
0x96
0x2B
Notes:
1. SCA1–SCA0 and T1M bit definitions can be found in Section 27.1.
2. X = Don’t care.
Table 25.2. Timer Settings for Standard Baud Rates
Using an External 22.1184 MHz Oscillator
Frequency: 22.1184 MHz
SYSCLK from
Internal Osc.
SYSCLK from
External Osc.
Target
Baud Rate
(bps)
230400
115200
57600
28800
14400
9600
2400
1200
230400
115200
57600
28800
14400
9600
Baud Rate
% Error
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
Timer Clock SCA1–SCA0
Oscillator Source
(pre-scale
Divide
select)1
Factor
96
192
384
768
1536
2304
9216
18432
96
192
384
768
1536
2304
SYSCLK
SYSCLK
SYSCLK
SYSCLK / 12
SYSCLK / 12
SYSCLK / 12
SYSCLK / 48
SYSCLK / 48
EXTCLK / 8
EXTCLK / 8
EXTCLK / 8
EXTCLK / 8
EXTCLK / 8
EXTCLK / 8
XX2
XX
XX
00
00
00
10
10
11
11
11
11
11
11
T1M1 Timer 1
Reload
Value (hex)
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0xD0
0xA0
0x40
0xE0
0xC0
0xA0
0xA0
0x40
0xFA
0xF4
0xE8
0xD0
0xA0
0x70
Notes:
1. SCA1–SCA0 and T1M bit definitions can be found in Section 27.1.
2. X = Don’t care.
Rev. 1.3
321
Si1000/1/2/3/4/5
26. Enhanced Serial Peripheral Interface (SPI0)
The Enhanced Serial Peripheral Interface (SPI0) provides access to a flexible, full-duplex synchronous
serial bus. SPI0 can operate as a master or slave device in both 3-wire or 4-wire modes, and supports
multiple masters and slaves on a single SPI bus. The slave-select (NSS) signal can be configured as an
input to select SPI0 in slave mode, or to disable Master Mode operation in a multi-master environment,
avoiding contention on the SPI bus when more than one master attempts simultaneous data transfers.
NSS can also be configured as a chip-select output in master mode, or disabled for 3-wire operation.
Additional general purpose port I/O pins can be used to select multiple slave devices in master mode.
SFR Bus
SYSCLK
SPI0CN
SPIBSY
MSTEN
CKPHA
CKPOL
SLVSEL
NSSIN
SRMT
RXBMT
SPIF
WCOL
MODF
RXOVRN
NSSMD1
NSSMD0
TXBMT
SPIEN
SPI0CFG
SCR7
SCR6
SCR5
SCR4
SCR3
SCR2
SCR1
SCR0
SPI0CKR
Clock Divide
Logic
SPI CONTROL LOGIC
Data Path
Control
SPI IRQ
Pin Interface
Control
MOSI
Tx Data
SPI0DAT
SCK
Transmit Data Buffer
Shift Register
Rx Data
7 6 5 4 3 2 1 0
Receive Data Buffer
Pin
Control
Logic
MISO
NSS
Read
SPI0DAT
Write
SPI0DAT
SFR Bus
Figure 26.1. SPI Block Diagram
322
Rev. 1.3
C
R
O
S
S
B
A
R
Port I/O
Si1000/1/2/3/4/5
26.1. Signal Descriptions
The four signals used by SPI0 (MOSI, MISO, SCK, NSS) are described below.
26.1.1. Master Out, Slave In (MOSI)
The master-out, slave-in (MOSI) signal is an output from a master device and an input to slave devices. It
is used to serially transfer data from the master to the slave. This signal is an output when SPI0 is
operating as a master and an input when SPI0 is operating as a slave. Data is transferred most-significant
bit first. When configured as a master, MOSI is driven by the MSB of the shift register in both 3- and 4-wire
mode.
26.1.2. Master In, Slave Out (MISO)
The master-in, slave-out (MISO) signal is an output from a slave device and an input to the master device.
It is used to serially transfer data from the slave to the master. This signal is an input when SPI0 is
operating as a master and an output when SPI0 is operating as a slave. Data is transferred mostsignificant bit first. The MISO pin is placed in a high-impedance state when the SPI module is disabled and
when the SPI operates in 4-wire mode as a slave that is not selected. When acting as a slave in 3-wire
mode, MISO is always driven by the MSB of the shift register.
26.1.3. Serial Clock (SCK)
The serial clock (SCK) signal is an output from the master device and an input to slave devices. It is used
to synchronize the transfer of data between the master and slave on the MOSI and MISO lines. SPI0
generates this signal when operating as a master. The SCK signal is ignored by a SPI slave when the
slave is not selected (NSS = 1) in 4-wire slave mode.
26.1.4. Slave Select (NSS)
The function of the slave-select (NSS) signal is dependent on the setting of the NSSMD1 and NSSMD0
bits in the SPI0CN register. There are three possible modes that can be selected with these bits:
1. NSSMD[1:0] = 00: 3-Wire Master or 3-Wire Slave Mode: SPI0 operates in 3-wire mode, and NSS is
disabled. When operating as a slave device, SPI0 is always selected in 3-wire mode. Since no select
signal is present, SPI0 must be the only slave on the bus in 3-wire mode. This is intended for point-topoint communication between a master and one slave.
2. NSSMD[1:0] = 01: 4-Wire Slave or Multi-Master Mode: SPI0 operates in 4-wire mode, and NSS is
enabled as an input. When operating as a slave, NSS selects the SPI0 device. When operating as a
master, a 1-to-0 transition of the NSS signal disables the master function of SPI0 so that multiple
master devices can be used on the same SPI bus.
3. NSSMD[1:0] = 1x: 4-Wire Master Mode: SPI0 operates in 4-wire mode, and NSS is enabled as an
output. The setting of NSSMD0 determines what logic level the NSS pin will output. This configuration
should only be used when operating SPI0 as a master device.
See Figure 26.2, Figure 26.3, and Figure 26.4 for typical connection diagrams of the various operational
modes. Note that the setting of NSSMD bits affects the pinout of the device. When in 3-wire master or
3-wire slave mode, the NSS pin will not be mapped by the crossbar. In all other modes, the NSS signal will
be mapped to a pin on the device. See Section “21. Port Input/Output” on page 210 for general purpose
port I/O and crossbar information.
26.2. SPI0 Master Mode Operation
A SPI master device initiates all data transfers on a SPI bus. SPI0 is placed in master mode by setting the
Master Enable flag (MSTEN, SPI0CN.6). Writing a byte of data to the SPI0 data register (SPI0DAT) when
in master mode writes to the transmit buffer. If the SPI shift register is empty, the byte in the transmit buffer
is moved to the shift register, and a data transfer begins. The SPI0 master immediately shifts out the data
serially on the MOSI line while providing the serial clock on SCK. The SPIF (SPI0CN.7) flag is set to logic
1 at the end of the transfer. If interrupts are enabled, an interrupt request is generated when the SPIF flag
is set. While the SPI0 master transfers data to a slave on the MOSI line, the addressed SPI slave device
simultaneously transfers the contents of its shift register to the SPI master on the MISO line in a full-duplex
Rev. 1.3
323
Si1000/1/2/3/4/5
operation. Therefore, the SPIF flag serves as both a transmit-complete and receive-data-ready flag. The
data byte received from the slave is transferred MSB-first into the master's shift register. When a byte is
fully shifted into the register, it is moved to the receive buffer where it can be read by the processor by
reading SPI0DAT.
When configured as a master, SPI0 can operate in one of three different modes: multi-master mode, 3-wire
single-master mode, and 4-wire single-master mode. The default, multi-master mode is active when
NSSMD1 (SPI0CN.3) = 0 and NSSMD0 (SPI0CN.2) = 1. In this mode, NSS is an input to the device, and
is used to disable the master SPI0 when another master is accessing the bus. When NSS is pulled low in
this mode, MSTEN (SPI0CN.6) and SPIEN (SPI0CN.0) are set to 0 to disable the SPI master device, and
a Mode Fault is generated (MODF, SPI0CN.5 = 1). Mode Fault will generate an interrupt if enabled. SPI0
must be manually re-enabled in software under these circumstances. In multi-master systems, devices will
typically default to being slave devices while they are not acting as the system master device. In multimaster mode, slave devices can be addressed individually (if needed) using general-purpose I/O pins.
Figure 26.2 shows a connection diagram between two master devices in multiple-master mode.
3-wire single-master mode is active when NSSMD1 (SPI0CN.3) = 0 and NSSMD0 (SPI0CN.2) = 0. In this
mode, NSS is not used, and is not mapped to an external port pin through the crossbar. Any slave devices
that must be addressed in this mode should be selected using general-purpose I/O pins. Figure 26.3
shows a connection diagram between a master device in 3-wire master mode and a slave device.
4-wire single-master mode is active when NSSMD1 (SPI0CN.3) = 1. In this mode, NSS is configured as an
output pin, and can be used as a slave-select signal for a single SPI device. In this mode, the output value
of NSS is controlled (in software) with the bit NSSMD0 (SPI0CN.2). Additional slave devices can be
addressed using general-purpose I/O pins. Figure 26.4 shows a connection diagram for a master device in
4-wire master mode and two slave devices.
Master
Device 1
NSS
GPIO
MISO
MISO
MOSI
MOSI
SCK
SCK
GPIO
NSS
Master
Device 2
Figure 26.2. Multiple-Master Mode Connection Diagram
Master
Device
MISO
MISO
MOSI
MOSI
SCK
SCK
Slave
Device
Figure 26.3. 3-Wire Single Master and 3-Wire Single Slave Mode Connection Diagram
324
Rev. 1.3
Si1000/1/2/3/4/5
Master
Device
GPIO
MISO
MISO
MOSI
MOSI
SCK
SCK
NSS
NSS
MISO
MOSI
Slave
Device
Slave
Device
SCK
NSS
Figure 26.4. 4-Wire Single Master Mode and 4-Wire Slave Mode Connection Diagram
26.3. SPI0 Slave Mode Operation
When SPI0 is enabled and not configured as a master, it will operate as a SPI slave. As a slave, bytes are
shifted in through the MOSI pin and out through the MISO pin by a master device controlling the SCK
signal. A bit counter in the SPI0 logic counts SCK edges. When 8 bits have been shifted through the shift
register, the SPIF flag is set to logic 1, and the byte is copied into the receive buffer. Data is read from the
receive buffer by reading SPI0DAT. A slave device cannot initiate transfers. Data to be transferred to the
master device is pre-loaded into the shift register by writing to SPI0DAT. Writes to SPI0DAT are doublebuffered, and are placed in the transmit buffer first. If the shift register is empty, the contents of the transmit
buffer will immediately be transferred into the shift register. When the shift register already contains data,
the SPI will load the shift register with the transmit buffer’s contents after the last SCK edge of the next (or
current) SPI transfer.
When configured as a slave, SPI0 can be configured for 4-wire or 3-wire operation. The default, 4-wire
slave mode, is active when NSSMD1 (SPI0CN.3) = 0 and NSSMD0 (SPI0CN.2) = 1. In 4-wire mode, the
NSS signal is routed to a port pin and configured as a digital input. SPI0 is enabled when NSS is logic 0,
and disabled when NSS is logic 1. The bit counter is reset on a falling edge of NSS. Note that the NSS
signal must be driven low at least 2 system clocks before the first active edge of SCK for each byte
transfer. Figure 26.4 shows a connection diagram between two slave devices in 4-wire slave mode and a
master device.
3-wire slave mode is active when NSSMD1 (SPI0CN.3) = 0 and NSSMD0 (SPI0CN.2) = 0. NSS is not
used in this mode, and is not mapped to an external port pin through the crossbar. Since there is no way of
uniquely addressing the device in 3-wire slave mode, SPI0 must be the only slave device present on the
bus. It is important to note that in 3-wire slave mode there is no external means of resetting the bit counter
that determines when a full byte has been received. The bit counter can only be reset by disabling and reenabling SPI0 with the SPIEN bit. Figure 26.3 shows a connection diagram between a slave device in 3wire slave mode and a master device.
Rev. 1.3
325
Si1000/1/2/3/4/5
26.4. SPI0 Interrupt Sources
When SPI0 interrupts are enabled, the following four flags will generate an interrupt when they are set to
logic 1:
All of the following bits must be cleared by software.
The SPI Interrupt Flag, SPIF (SPI0CN.7) is set to logic 1 at the end of each byte transfer. This flag can
occur in all SPI0 modes.
 The Write Collision Flag, WCOL (SPI0CN.6) is set to logic 1 if a write to SPI0DAT is attempted when
the transmit buffer has not been emptied to the SPI shift register. When this occurs, the write to
SPI0DAT will be ignored, and the transmit buffer will not be written.This flag can occur in all SPI0
modes.
 The Mode Fault Flag MODF (SPI0CN.5) is set to logic 1 when SPI0 is configured as a master, and for
multi-master mode and the NSS pin is pulled low. When a Mode Fault occurs, the MSTEN and SPIEN
bits in SPI0CN are set to logic 0 to disable SPI0 and allow another master device to access the bus.
 The Receive Overrun Flag RXOVRN (SPI0CN.4) is set to logic 1 when configured as a slave, and a
transfer is completed and the receive buffer still holds an unread byte from a previous transfer. The new
byte is not transferred to the receive buffer, allowing the previously received data byte to be read. The
data byte which caused the overrun is lost.

326
Rev. 1.3
Si1000/1/2/3/4/5
26.5. Serial Clock Phase and Polarity
Four combinations of serial clock phase and polarity can be selected using the clock control bits in the
SPI0 Configuration Register (SPI0CFG). The CKPHA bit (SPI0CFG.5) selects one of two clock phases
(edge used to latch the data). The CKPOL bit (SPI0CFG.4) selects between an active-high or active-low
clock. Both master and slave devices must be configured to use the same clock phase and polarity. SPI0
should be disabled (by clearing the SPIEN bit, SPI0CN.0) when changing the clock phase or polarity. The
clock and data line relationships for master mode are shown in Figure 26.5. For slave mode, the clock and
data relationships are shown in Figure 26.6 and Figure 26.7. Note that CKPHA should be set to 0 on both
the master and slave SPI when communicating between two Silicon Labs C8051 devices.
The SPI0 Clock Rate Register (SPI0CKR) as shown in SFR Definition 26.9 controls the master mode
serial clock frequency. This register is ignored when operating in slave mode. When the SPI is configured
as a master, the maximum data transfer rate (bits/sec) is one-half the system clock frequency or 12.5 MHz,
whichever is slower. When the SPI is configured as a slave, the maximum data transfer rate (bits/sec) for
full-duplex operation is 1/10 the system clock frequency, provided that the master issues SCK, NSS (in 4wire slave mode), and the serial input data synchronously with the slave’s system clock. If the master
issues SCK, NSS, and the serial input data asynchronously, the maximum data transfer rate (bits/sec)
must be less than 1/10 the system clock frequency. In the special case where the master only wants to
transmit data to the slave and does not need to receive data from the slave (i.e. half-duplex operation), the
SPI slave can receive data at a maximum data transfer rate (bits/sec) of 1/4 the system clock frequency.
This is provided that the master issues SCK, NSS, and the serial input data synchronously with the slave’s
system clock.
SCK
(CKPOL=0, CKPHA=0)
SCK
(CKPOL=0, CKPHA=1)
SCK
(CKPOL=1, CKPHA=0)
SCK
(CKPOL=1, CKPHA=1)
MISO/MOSI
MSB
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
NSS (Must Remain High
in Multi-Master Mode)
Figure 26.5. Master Mode Data/Clock Timing
Rev. 1.3
327
Si1000/1/2/3/4/5
SCK
(CKPOL=0, CKPHA=0)
SCK
(CKPOL=1, CKPHA=0)
MOSI
MSB
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
MISO
MSB
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
NSS (4-Wire Mode)
Figure 26.6. Slave Mode Data/Clock Timing (CKPHA = 0)
SCK
(CKPOL=0, CKPHA=1)
SCK
(CKPOL=1, CKPHA=1)
MOSI
MSB
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
MISO
MSB
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Bit 0
NSS (4-Wire Mode)
Figure 26.7. Slave Mode Data/Clock Timing (CKPHA = 1)
26.6. SPI Special Function Registers
SPI0 is accessed and controlled through four special function registers in the system controller: SPI0CN
Control Register, SPI0DAT Data Register, SPI0CFG Configuration Register, and SPI0CKR Clock Rate
Register. The four special function registers related to the operation of the SPI0 Bus are described in the
following figures.
328
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 26.7. SPI0CFG: SPI0 Configuration
Bit
7
6
5
4
3
2
1
0
Name
SPIBSY
MSTEN
CKPHA
CKPOL
SLVSEL
NSSIN
SRMT
RXBMT
Type
R
R/W
R/W
R/W
R
R
R
R
Reset
0
0
0
0
0
1
1
1
SFR Page = 0x0; SFR Address = 0xA1
Bit
Name
7
SPIBSY
Function
SPI Busy.
This bit is set to logic 1 when a SPI transfer is in progress (master or slave mode).
6
MSTEN
Master Mode Enable.
0: Disable master mode. Operate in slave mode.
1: Enable master mode. Operate as a master.
5
CKPHA
SPI0 Clock Phase.
0: Data centered on first edge of SCK period.*
1: Data centered on second edge of SCK period.*
4
CKPOL
SPI0 Clock Polarity.
0: SCK line low in idle state.
1: SCK line high in idle state.
3
SLVSEL
Slave Selected Flag.
This bit is set to logic 1 whenever the NSS pin is low indicating SPI0 is the selected
slave. It is cleared to logic 0 when NSS is high (slave not selected). This bit does
not indicate the instantaneous value at the NSS pin, but rather a de-glitched version of the pin input.
2
NSSIN
NSS Instantaneous Pin Input.
This bit mimics the instantaneous value that is present on the NSS port pin at the
time that the register is read. This input is not de-glitched.
1
SRMT
Shift Register Empty (valid in slave mode only).
This bit will be set to logic 1 when all data has been transferred in/out of the shift
register, and there is no new information available to read from the transmit buffer
or write to the receive buffer. It returns to logic 0 when a data byte is transferred to
the shift register from the transmit buffer or by a transition on SCK. SRMT = 1 when
in Master Mode.
0
RXBMT
Receive Buffer Empty (valid in slave mode only).
This bit will be set to logic 1 when the receive buffer has been read and contains no
new information. If there is new information available in the receive buffer that has
not been read, this bit will return to logic 0. RXBMT = 1 when in Master Mode.
Note: In slave mode, data on MOSI is sampled in the center of each data bit. In master mode, data on MISO is
sampled one SYSCLK before the end of each data bit, to provide maximum settling time for the slave device.
See Table 26.1 for timing parameters.
Rev. 1.3
329
Si1000/1/2/3/4/5
SFR Definition 26.8. SPI0CN: SPI0 Control
Bit
7
6
5
4
Name
SPIF
WCOL
MODF
RXOVRN
Type
R/W
R/W
R/W
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xF8; Bit-Addressable
Bit
Name
7
SPIF
3
2
1
0
NSSMD[1:0]
TXBMT
SPIEN
R/W
R
R/W
1
0
0
1
Function
SPI0 Interrupt Flag.
This bit is set to logic 1 by hardware at the end of a data transfer. If SPI interrupts
are enabled, an interrupt will be generated. This bit is not automatically cleared by
hardware, and must be cleared by software.
6
WCOL
Write Collision Flag.
This bit is set to logic 1 if a write to SPI0DAT is attempted when TXBMT is 0. When
this occurs, the write to SPI0DAT will be ignored, and the transmit buffer will not be
written. If SPI interrupts are enabled, an interrupt will be generated. This bit is not
automatically cleared by hardware, and must be cleared by software.
5
MODF
Mode Fault Flag.
This bit is set to logic 1 by hardware when a master mode collision is detected
(NSS is low, MSTEN = 1, and NSSMD[1:0] = 01). If SPI interrupts are enabled, an
interrupt will be generated. This bit is not automatically cleared by hardware, and
must be cleared by software.
4
RXOVRN
Receive Overrun Flag (valid in slave mode only).
This bit is set to logic 1 by hardware when the receive buffer still holds unread data
from a previous transfer and the last bit of the current transfer is shifted into the
SPI0 shift register. If SPI interrupts are enabled, an interrupt will be generated. This
bit is not automatically cleared by hardware, and must be cleared by software.
3:2
NSSMD[1:0]
Slave Select Mode.
Selects between the following NSS operation modes:
(See Section 26.2 and Section 26.3).
00: 3-Wire Slave or 3-Wire Master Mode. NSS signal is not routed to a port pin.
01: 4-Wire Slave or Multi-Master Mode (Default). NSS is an input to the device.
1x: 4-Wire Single-Master Mode. NSS signal is mapped as an output from the
device and will assume the value of NSSMD0.
1
TXBMT
Transmit Buffer Empty.
This bit will be set to logic 0 when new data has been written to the transmit buffer.
When data in the transmit buffer is transferred to the SPI shift register, this bit will
be set to logic 1, indicating that it is safe to write a new byte to the transmit buffer.
0
SPIEN
SPI0 Enable.
0: SPI disabled.
1: SPI enabled.
330
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 26.9. SPI0CKR: SPI0 Clock Rate
Bit
7
6
5
4
Name
SCR[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xA2
Bit
Name
7:0
SCR[7:0]
3
2
1
0
0
0
0
0
Function
SPI0 Clock Rate.
These bits determine the frequency of the SCK output when the SPI0 module is
configured for master mode operation. The SCK clock frequency is a divided version of the system clock, and is given in the following equation, where SYSCLK is
the system clock frequency and SPI0CKR is the 8-bit value held in the SPI0CKR
register.
SYSCLK
f SCK = ----------------------------------------------------------2   SPI0CKR[7:0] + 1 
for 0 <= SPI0CKR <= 255
Example: If SYSCLK = 2 MHz and SPI0CKR = 0x04,
2000000
f SCK = -------------------------2  4 + 1
f SCK = 200kHz
SFR Definition 26.10. SPI0DAT: SPI0 Data
Bit
7
6
5
4
3
Name
SPI0DAT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xA3
Bit
Name
7:0
0
2
1
0
0
0
0
Function
SPI0DAT[7:0] SPI0 Transmit and Receive Data.
The SPI0DAT register is used to transmit and receive SPI0 data. Writing data to
SPI0DAT places the data into the transmit buffer and initiates a transfer when in
Master Mode. A read of SPI0DAT returns the contents of the receive buffer.
Rev. 1.3
331
Si1000/1/2/3/4/5
SCK*
T
T
MCKH
MCKL
T
T
MIS
MIH
MISO
MOSI
* SCK is shown for CKPOL = 0. SCK is the opposite polarity for CKPOL = 1.
Figure 26.8. SPI Master Timing (CKPHA = 0)
SCK*
T
T
MCKH
MCKL
T
T
MIS
MIH
MISO
MOSI
* SCK is shown for CKPOL = 0. SCK is the opposite polarity for CKPOL = 1.
Figure 26.9. SPI Master Timing (CKPHA = 1)
332
Rev. 1.3
Si1000/1/2/3/4/5
NSS
T
T
SE
T
CKL
SD
SCK*
T
CKH
T
SIS
T
SIH
MOSI
T
T
SEZ
T
SOH
SDZ
MISO
* SCK is shown for CKPOL = 0. SCK is the opposite polarity for CKPOL = 1.
Figure 26.10. SPI Slave Timing (CKPHA = 0)
NSS
T
T
SE
T
CKL
SD
SCK*
T
CKH
T
SIS
T
SIH
MOSI
T
SEZ
T
T
SOH
SLH
T
SDZ
MISO
* SCK is shown for CKPOL = 0. SCK is the opposite polarity for CKPOL = 1.
Figure 26.11. SPI Slave Timing (CKPHA = 1)
Rev. 1.3
333
Si1000/1/2/3/4/5
Table 26.1. SPI Slave Timing Parameters
Parameter
Description
Min
Max
Units
Master Mode Timing (See Figure 26.8 and Figure 26.9)
TMCKH
SCK High Time
1 x TSYSCLK
—
ns
TMCKL
SCK Low Time
1 x TSYSCLK
—
ns
TMIS
MISO Valid to SCK Shift Edge
1 x TSYSCLK + 20
—
ns
TMIH
SCK Shift Edge to MISO Change
0
—
ns
Slave Mode Timing (See Figure 26.10 and Figure 26.11)
TSE
NSS Falling to First SCK Edge
2 x TSYSCLK
—
ns
TSD
Last SCK Edge to NSS Rising
2 x TSYSCLK
—
ns
TSEZ
NSS Falling to MISO Valid
—
4 x TSYSCLK
ns
TSDZ
NSS Rising to MISO High-Z
—
4 x TSYSCLK
ns
TCKH
SCK High Time
5 x TSYSCLK
—
ns
TCKL
SCK Low Time
5 x TSYSCLK
—
ns
TSIS
MOSI Valid to SCK Sample Edge
2 x TSYSCLK
—
ns
TSIH
SCK Sample Edge to MOSI Change
2 x TSYSCLK
—
ns
TSOH
SCK Shift Edge to MISO Change
—
4 x TSYSCLK
ns
TSLH
Last SCK Edge to MISO Change 
(CKPHA = 1 ONLY)
6 x TSYSCLK
8 x TSYSCLK
ns
Note: TSYSCLK is equal to one period of the device system clock (SYSCLK).
334
Rev. 1.3
Si1000/1/2/3/4/5
27. Timers
Each MCU includes four counter/timers: two are 16-bit counter/timers compatible with those found in the
standard 8051, and two are 16-bit auto-reload timer for use with the ADC, SMBus, or for general purpose
use. These timers can be used to measure time intervals, count external events and generate periodic
interrupt requests. Timer 0 and Timer 1 are nearly identical and have four primary modes of operation.
Timer 2 and Timer 3 offer 16-bit and split 8-bit timer functionality with auto-reload. Additionally, Timer 2 and
Timer 3 have a Capture Mode that can be used to measure the SmaRTClock or a Comparator period with
respect to another oscillator. This is particularly useful when using Capacitive Touch Switches. See Application Note AN338 for details on Capacitive Touch Switch sensing.
Timer 0 and Timer 1 Modes:
Timer 2 Modes:
Timer 3 Modes:
13-bit counter/timer
16-bit timer with auto-reload
16-bit timer with auto-reload
Two 8-bit timers with auto-reload
Two 8-bit timers with auto-reload
16-bit counter/timer
8-bit counter/timer with autoreload
Two 8-bit counter/timers (Timer 0
only)
Timers 0 and 1 may be clocked by one of five sources, determined by the Timer Mode Select bits (T1M–
T0M) and the Clock Scale bits (SCA1–SCA0). The Clock Scale bits define a pre-scaled clock from which
Timer 0 and/or Timer 1 may be clocked (See SFR Definition 27.1 for pre-scaled clock selection).
Timer 0/1 may then be configured to use this pre-scaled clock signal or the system clock. Timer 2 and
Timer 3 may be clocked by the system clock, the system clock divided by 12. Timer 2 may additionally be
clocked by the SmaRTClock divided by 8 or the Comparator0 output. Timer 3 may additionally be clocked
by the external oscillator clock source divided by 8 or the Comparator1 output.
Timer 0 and Timer 1 may also be operated as counters. When functioning as a counter, a counter/timer
register is incremented on each high-to-low transition at the selected input pin (T0 or T1). Events with a frequency of up to one-fourth the system clock frequency can be counted. The input signal need not be periodic, but it should be held at a given level for at least two full system clock cycles to ensure the level is
properly sampled.
Rev. 1.3
335
Si1000/1/2/3/4/5
SFR Definition 27.1. CKCON: Clock Control
Bit
7
6
5
4
3
2
Name
T3MH
T3ML
T2MH
T2ML
T1M
T0M
SCA[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0x8E
Bit
Name
7
T3MH
1
0
0
0
Function
Timer 3 High Byte Clock Select.
Selects the clock supplied to the Timer 3 high byte (split 8-bit timer mode only).
0: Timer 3 high byte uses the clock defined by the T3XCLK bit in TMR3CN.
1: Timer 3 high byte uses the system clock.
6
T3ML
Timer 3 Low Byte Clock Select.
Selects the clock supplied to Timer 3. Selects the clock supplied to the lower 8-bit timer
in split 8-bit timer mode.
0: Timer 3 low byte uses the clock defined by the T3XCLK bit in TMR3CN.
1: Timer 3 low byte uses the system clock.
5
T2MH
Timer 2 High Byte Clock Select.
Selects the clock supplied to the Timer 2 high byte (split 8-bit timer mode only).
0: Timer 2 high byte uses the clock defined by the T2XCLK bit in TMR2CN.
1: Timer 2 high byte uses the system clock.
4
T2ML
Timer 2 Low Byte Clock Select.
Selects the clock supplied to Timer 2. If Timer 2 is configured in split 8-bit timer mode,
this bit selects the clock supplied to the lower 8-bit timer.
0: Timer 2 low byte uses the clock defined by the T2XCLK bit in TMR2CN.
1: Timer 2 low byte uses the system clock.
3
T1M
Timer 1 Clock Select.
Selects the clock source supplied to Timer 1. Ignored when C/T1 is set to 1.
0: Timer 1 uses the clock defined by the prescale bits SCA[1:0].
1: Timer 1 uses the system clock.
2
T0M
Timer 0 Clock Select.
Selects the clock source supplied to Timer 0. Ignored when C/T0 is set to 1.
0: Counter/Timer 0 uses the clock defined by the prescale bits SCA[1:0].
1: Counter/Timer 0 uses the system clock.
1:0
SCA[1:0] Timer 0/1 Prescale Bits.
These bits control the Timer 0/1 Clock Prescaler:
00: System clock divided by 12
01: System clock divided by 4
10: System clock divided by 48
11: External clock divided by 8 (synchronized with the system clock)
336
Rev. 1.3
Si1000/1/2/3/4/5
27.1. Timer 0 and Timer 1
Each timer is implemented as a 16-bit register accessed as two separate bytes: a low byte (TL0 or TL1)
and a high byte (TH0 or TH1). The Counter/Timer Control register (TCON) is used to enable Timer 0 and
Timer 1 as well as indicate status. Timer 0 interrupts can be enabled by setting the ET0 bit in the IE register (Section “12.5. Interrupt Register Descriptions” on page 133); Timer 1 interrupts can be enabled by setting the ET1 bit in the IE register (Section “12.5. Interrupt Register Descriptions” on page 133). Both
counter/timers operate in one of four primary modes selected by setting the Mode Select bits T1M1–T0M0
in the Counter/Timer Mode register (TMOD). Each timer can be configured independently. Each operating
mode is described below.
27.1.1. Mode 0: 13-bit Counter/Timer
Timer 0 and Timer 1 operate as 13-bit counter/timers in Mode 0. The following describes the configuration
and operation of Timer 0. However, both timers operate identically, and Timer 1 is configured in the same
manner as described for Timer 0.
The TH0 register holds the eight MSBs of the 13-bit counter/timer. TL0 holds the five LSBs in bit positions
TL0.4–TL0.0. The three upper bits of TL0 (TL0.7–TL0.5) are indeterminate and should be masked out or
ignored when reading. As the 13-bit timer register increments and overflows from 0x1FFF (all ones) to
0x0000, the timer overflow flag TF0 (TCON.5) is set and an interrupt will occur if Timer 0 interrupts are
enabled.
The C/T0 bit (TMOD.2) selects the counter/timer's clock source. When C/T0 is set to logic 1, high-to-low
transitions at the selected Timer 0 input pin (T0) increment the timer register (Refer to Section
“21.3. Priority Crossbar Decoder” on page 214 for information on selecting and configuring external I/O
pins). Clearing C/T selects the clock defined by the T0M bit (CKCON.3). When T0M is set, Timer 0 is
clocked by the system clock. When T0M is cleared, Timer 0 is clocked by the source selected by the Clock
Scale bits in CKCON (see SFR Definition 27.1).
Setting the TR0 bit (TCON.4) enables the timer when either GATE0 (TMOD.3) is logic 0 or the input signal
INT0 is active as defined by bit IN0PL in register IT01CF (see SFR Definition 12.7). Setting GATE0 to 1
allows the timer to be controlled by the external input signal INT0 (see Section “12.5. Interrupt Register
Descriptions” on page 133), facilitating pulse width measurements
Table 27.1. Timer 0 Running Modes
TR0
GATE0
INT0
Counter/Timer
0
X
X
Disabled
1
0
X
Enabled
1
1
0
Disabled
1
1
1
Enabled
Note: X = Don't Care
Setting TR0 does not force the timer to reset. The timer registers should be loaded with the desired initial
value before the timer is enabled.
TL1 and TH1 form the 13-bit register for Timer 1 in the same manner as described above for TL0 and TH0.
Timer 1 is configured and controlled using the relevant TCON and TMOD bits just as with Timer 0. The
input signal INT1 is used with Timer 1; the INT1 polarity is defined by bit IN1PL in register IT01CF (see
SFR Definition 12.7).
Rev. 1.3
337
Si1000/1/2/3/4/5
CKCON
T
3
M
H
P re -s ca le d C lo c k
0
SYSCLK
1
T
3
M
L
T
2
M
H
TM OD
T T T S S
2 1 0 C C
MMM A A
1 0
L
G
A
T
E
1
C
/
T
1
T
1
M
1
T
1
M
0
G
A
T
E
0
C
/
T
0
IT 0 1 C F
T
0
M
1
T
0
M
0
I
N
1
P
L
I
N
1
S
L
2
I
N
1
S
L
1
I
N
1
S
L
0
I
N
0
P
L
I
N
0
S
L
2
I
N
0
S
L
1
I
N
0
S
L
0
0
1
TCLK
TR0
C ro ss b a r
IN T 0
TL0
(5 b its )
TH0
(8 b its)
G ATE0
IN 0 P L
TCON
T0
TF1
TR1
TF0
TR0
IE 1
IT 1
IE 0
IT 0
Inte rru pt
XOR
Figure 27.1. T0 Mode 0 Block Diagram
27.1.2. Mode 1: 16-bit Counter/Timer
Mode 1 operation is the same as Mode 0, except that the counter/timer registers use all 16 bits. The
counter/timers are enabled and configured in Mode 1 in the same manner as for Mode 0.
27.1.3. Mode 2: 8-bit Counter/Timer with Auto-Reload
Mode 2 configures Timer 0 and Timer 1 to operate as 8-bit counter/timers with automatic reload of the start
value. TL0 holds the count and TH0 holds the reload value. When the counter in TL0 overflows from all
ones to 0x00, the timer overflow flag TF0 (TCON.5) is set and the counter in TL0 is reloaded from TH0. If
Timer 0 interrupts are enabled, an interrupt will occur when the TF0 flag is set. The reload value in TH0 is
not changed. TL0 must be initialized to the desired value before enabling the timer for the first count to be
correct. When in Mode 2, Timer 1 operates identically to Timer 0.
Both counter/timers are enabled and configured in Mode 2 in the same manner as Mode 0. Setting the
TR0 bit (TCON.4) enables the timer when either GATE0 (TMOD.3) is logic 0 or when the input signal INT0
is active as defined by bit IN0PL in register IT01CF (see Section “12.6. External Interrupts INT0 and INT1”
on page 140 for details on the external input signals INT0 and INT1).
338
Rev. 1.3
Si1000/1/2/3/4/5
CKCON
T T T T T T S
3 3 2 2 1 0 C
MMMMMMA
H L H L
1
Pre-scaled Clock
TMOD
S
C
A
0
G
A
T
E
1
C
/
T
1
T
1
M
1
T
1
M
0
G
A
T
E
0
C
/
T
0
IT01CF
T
0
M
1
T
0
M
0
I
N
1
P
L
I
N
1
S
L
2
I
N
1
S
L
1
I
N
1
S
L
0
I
N
0
P
L
I
N
0
S
L
2
I
N
0
S
L
1
I
N
0
S
L
0
0
0
SYSCLK
1
1
T0
TL0
(8 bits)
TCON
TCLK
TR0
Crossbar
GATE0
TH0
(8 bits)
INT0
IN0PL
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
Interrupt
Reload
XOR
Figure 27.2. T0 Mode 2 Block Diagram
27.1.4. Mode 3: Two 8-bit Counter/Timers (Timer 0 Only)
In Mode 3, Timer 0 is configured as two separate 8-bit counter/timers held in TL0 and TH0. The
counter/timer in TL0 is controlled using the Timer 0 control/status bits in TCON and TMOD: TR0, C/T0,
GATE0 and TF0. TL0 can use either the system clock or an external input signal as its timebase. The TH0
register is restricted to a timer function sourced by the system clock or prescaled clock. TH0 is enabled
using the Timer 1 run control bit TR1. TH0 sets the Timer 1 overflow flag TF1 on overflow and thus controls
the Timer 1 interrupt.
Timer 1 is inactive in Mode 3. When Timer 0 is operating in Mode 3, Timer 1 can be operated in Modes 0,
1 or 2, but cannot be clocked by external signals nor set the TF1 flag and generate an interrupt. However,
the Timer 1 overflow can be used to generate baud rates for the SMBus and/or UART, and/or initiate ADC
conversions. While Timer 0 is operating in Mode 3, Timer 1 run control is handled through its mode settings. To run Timer 1 while Timer 0 is in Mode 3, set the Timer 1 Mode as 0, 1, or 2. To disable Timer 1,
configure it for Mode 3.
Rev. 1.3
339
Si1000/1/2/3/4/5
CKCON
T T T T T T S
3 3 2 2 1 0 C
MMMMMMA
H L H L
1
Pre-scaled Clock
TMOD
S
C
A
0
G
A
T
E
1
C
/
T
1
T
1
M
1
T
1
M
0
G
A
T
E
0
C
/
T
0
T
0
M
1
T
0
M
0
0
TR1
1
0
TCON
SYSCLK
TH0
(8 bits)
1
T0
TL0
(8 bits)
TR0
Crossbar
INT0
GATE0
IN0PL
XOR
Figure 27.3. T0 Mode 3 Block Diagram
340
Rev. 1.3
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
Interrupt
Interrupt
Si1000/1/2/3/4/5
SFR Definition 27.2. TCON: Timer Control
Bit
7
6
5
4
3
2
1
0
Name
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0x88; Bit-Addressable
Bit
Name
Function
7
TF1
Timer 1 Overflow Flag.
Set to 1 by hardware when Timer 1 overflows. This flag can be cleared by software
but is automatically cleared when the CPU vectors to the Timer 1 interrupt service
routine.
6
TR1
Timer 1 Run Control.
Timer 1 is enabled by setting this bit to 1.
5
TF0
Timer 0 Overflow Flag.
Set to 1 by hardware when Timer 0 overflows. This flag can be cleared by software
but is automatically cleared when the CPU vectors to the Timer 0 interrupt service
routine.
4
TR0
Timer 0 Run Control.
Timer 0 is enabled by setting this bit to 1.
3
IE1
External Interrupt 1.
This flag is set by hardware when an edge/level of type defined by IT1 is detected. It
can be cleared by software but is automatically cleared when the CPU vectors to the
External Interrupt 1 service routine in edge-triggered mode.
2
IT1
Interrupt 1 Type Select.
This bit selects whether the configured INT1 interrupt will be edge or level sensitive.
INT1 is configured active low or high by the IN1PL bit in the IT01CF register (see
SFR Definition 12.7).
0: INT1 is level triggered.
1: INT1 is edge triggered.
1
IE0
External Interrupt 0.
This flag is set by hardware when an edge/level of type defined by IT1 is detected. It
can be cleared by software but is automatically cleared when the CPU vectors to the
External Interrupt 0 service routine in edge-triggered mode.
0
IT0
Interrupt 0 Type Select.
This bit selects whether the configured INT0 interrupt will be edge or level sensitive.
INT0 is configured active low or high by the IN0PL bit in register IT01CF (see SFR
Definition 12.7).
0: INT0 is level triggered.
1: INT0 is edge triggered.
Rev. 1.3
341
Si1000/1/2/3/4/5
SFR Definition 27.3. TMOD: Timer Mode
Bit
7
6
Name
GATE1
C/T1
Type
R/W
R/W
Reset
0
0
5
4
3
2
T1M[1:0]
GATE0
C/T0
T0M[1:0]
R/W
R/W
R/W
R/W
0
0
0
0
SFR Page = 0x0; SFR Address = 0x89
Bit
Name
7
GATE1
1
0
0
0
Function
Timer 1 Gate Control.
0: Timer 1 enabled when TR1 = 1 irrespective of INT1 logic level.
1: Timer 1 enabled only when TR1 = 1 AND INT1 is active as defined by bit IN1PL in
register IT01CF (see SFR Definition 12.7).
6
C/T1
Counter/Timer 1 Select.
0: Timer: Timer 1 incremented by clock defined by T1M bit in register CKCON.
1: Counter: Timer 1 incremented by high-to-low transitions on external pin (T1).
5:4
T1M[1:0]
Timer 1 Mode Select.
These bits select the Timer 1 operation mode.
00: Mode 0, 13-bit Counter/Timer
01: Mode 1, 16-bit Counter/Timer
10: Mode 2, 8-bit Counter/Timer with Auto-Reload
11: Mode 3, Timer 1 Inactive
3
GATE0
Timer 0 Gate Control.
0: Timer 0 enabled when TR0 = 1 irrespective of INT0 logic level.
1: Timer 0 enabled only when TR0 = 1 AND INT0 is active as defined by bit IN0PL in
register IT01CF (see SFR Definition 12.7).
2
C/T0
Counter/Timer 0 Select.
0: Timer: Timer 0 incremented by clock defined by T0M bit in register CKCON.
1: Counter: Timer 0 incremented by high-to-low transitions on external pin (T0).
1:0
T0M[1:0]
Timer 0 Mode Select.
These bits select the Timer 0 operation mode.
00: Mode 0, 13-bit Counter/Timer
01: Mode 1, 16-bit Counter/Timer
10: Mode 2, 8-bit Counter/Timer with Auto-Reload
11: Mode 3, Two 8-bit Counter/Timers
342
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 27.4. TL0: Timer 0 Low Byte
Bit
7
6
5
4
Name
TL0[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0x8A
Bit
Name
7:0
TL0[7:0]
3
2
1
0
0
0
0
0
3
2
1
0
0
0
0
0
Function
Timer 0 Low Byte.
The TL0 register is the low byte of the 16-bit Timer 0.
SFR Definition 27.5. TL1: Timer 1 Low Byte
Bit
7
6
5
4
Name
TL1[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0x8B
Bit
Name
7:0
TL1[7:0]
Function
Timer 1 Low Byte.
The TL1 register is the low byte of the 16-bit Timer 1.
Rev. 1.3
343
Si1000/1/2/3/4/5
SFR Definition 27.6. TH0: Timer 0 High Byte
Bit
7
6
5
4
Name
TH0[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0x8C
Bit
Name
7:0
TH0[7:0]
3
2
1
0
0
0
0
0
Function
Timer 0 High Byte.
The TH0 register is the high byte of the 16-bit Timer 0.
SFR Definition 27.7. TH1: Timer 1 High Byte
Bit
7
6
5
4
Name
TH1[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0x8D
Bit
Name
7:0
TH1[7:0]
3
2
1
0
0
0
0
0
Function
Timer 1 High Byte.
The TH1 register is the high byte of the 16-bit Timer 1.
344
Rev. 1.3
Si1000/1/2/3/4/5
27.2. Timer 2
Timer 2 is a 16-bit timer formed by two 8-bit SFRs: TMR2L (low byte) and TMR2H (high byte). Timer 2 may
operate in 16-bit auto-reload mode or (split) 8-bit auto-reload mode. The T2SPLIT bit (TMR2CN.3) defines
the Timer 2 operation mode. Timer 2 can also be used in Capture Mode to measure the SmaRTClock or
the Comparator 0 period with respect to another oscillator. The ability to measure the Comparator 0 period
with respect to the system clock is makes using Touch Sense Switches very easy.
Timer 2 may be clocked by the system clock, the system clock divided by 12, SmaRTClock divided by 8, or
Comparator 0 output. Note that the SmaRTClock divided by 8 and Comparator 0 output is synchronized
with the system clock.
27.2.1. 16-bit Timer with Auto-Reload
When T2SPLIT (TMR2CN.3) is zero, Timer 2 operates as a 16-bit timer with auto-reload. Timer 2 can be
clocked by SYSCLK, SYSCLK divided by 12, SmaRTClock divided by 8, or Comparator 0 output. As the
16-bit timer register increments and overflows from 0xFFFF to 0x0000, the 16-bit value in the Timer 2
reload registers (TMR2RLH and TMR2RLL) is loaded into the Timer 2 register as shown in Figure 27.4,
and the Timer 2 High Byte Overflow Flag (TMR2CN.7) is set. If Timer 2 interrupts are enabled (if IE.5 is
set), an interrupt will be generated on each Timer 2 overflow. Additionally, if Timer 2 interrupts are enabled
and the TF2LEN bit is set (TMR2CN.5), an interrupt will be generated each time the lower 8 bits (TMR2L)
overflow from 0xFF to 0x00.
CKCON
T2XCLK[1:0]
00
SmaRTClock / 8
01
Comparator 0
11
TL2
Overflow
0
TR2
TCLK
TMR2L
To ADC,
SMBus
To SMBus
TMR2H
TMR2CN
SYSCLK / 12
TTTTTTSS
3 3 2 2 1 0 CC
MMMMMM A A
HLHL
10
1
SYSCLK
TF2H
TF2L
TF2LEN
TF2CEN
T2SPLIT
TR2
Interrupt
T2XCLK
TMR2RLL TMR2RLH
Reload
Figure 27.4. Timer 2 16-Bit Mode Block Diagram
27.2.2. 8-bit Timers with Auto-Reload
When T2SPLIT is set, Timer 2 operates as two 8-bit timers (TMR2H and TMR2L). Both 8-bit timers operate in auto-reload mode as shown in Figure 27.5. TMR2RLL holds the reload value for TMR2L; TMR2RLH
holds the reload value for TMR2H. The TR2 bit in TMR2CN handles the run control for TMR2H. TMR2L is
always running when configured for 8-bit Mode.
Rev. 1.3
345
Si1000/1/2/3/4/5
Each 8-bit timer may be configured to use SYSCLK, SYSCLK divided by 12, SmaRTClock divided by 8 or
Comparator 0 output. The Timer 2 Clock Select bits (T2MH and T2ML in CKCON) select either SYSCLK or
the clock defined by the Timer 2 External Clock Select bits (T2XCLK[1:0] in TMR2CN), as follows:
T2MH
T2XCLK[1:0]
TMR2H Clock
Source
T2ML
T2XCLK[1:0]
TMR2L Clock
Source
0
00
SYSCLK / 12
0
00
SYSCLK / 12
0
01
SmaRTClock / 8
0
01
SmaRTClock / 8
0
10
Reserved
0
10
Reserved
0
11
Comparator 0
0
11
Comparator 0
1
X
SYSCLK
1
X
SYSCLK
The TF2H bit is set when TMR2H overflows from 0xFF to 0x00; the TF2L bit is set when TMR2L overflows
from 0xFF to 0x00. When Timer 2 interrupts are enabled (IE.5), an interrupt is generated each time
TMR2H overflows. If Timer 2 interrupts are enabled and TF2LEN (TMR2CN.5) is set, an interrupt is generated each time either TMR2L or TMR2H overflows. When TF2LEN is enabled, software must check the
TF2H and TF2L flags to determine the source of the Timer 2 interrupt. The TF2H and TF2L interrupt flags
are not cleared by hardware and must be manually cleared by software.
CKCON
TTTTTTSS
3 3 2 2 1 0 CC
MMMMMM A A
HLHL
1 0
T2XCLK[1:0]
SYSCLK / 12
00
SmaRTClock / 8
01
TMR2RLH
Reload
To SMBus
0
TCLK
TR2
11
TMR2RLL
SYSCLK
Reload
TMR2CN
Comparator 0
TMR2H
1
TF2H
TF2L
TF2LEN
TF2CEN
T2SPLIT
TR2
T2XCLK
1
TCLK
TMR2L
To ADC,
SMBus
0
Figure 27.5. Timer 2 8-Bit Mode Block Diagram
346
Rev. 1.3
Interrupt
Si1000/1/2/3/4/5
27.2.3. Comparator 0/SmaRTClock Capture Mode
The Capture Mode in Timer 2 allows either Comparator 0 or the SmaRTClock period to be measured
against the system clock or the system clock divided by 12. Comparator 0 and the SmaRTClock period can
also be compared against each other. Timer 2 Capture Mode is enabled by setting TF2CEN to 1. Timer 2
should be in 16-bit auto-reload mode when using Capture Mode.
When Capture Mode is enabled, a capture event will be generated either every Comparator 0 rising edge
or every 8 SmaRTClock clock cycles, depending on the T2XCLK1 setting. When the capture event occurs,
the contents of Timer 2 (TMR2H:TMR2L) are loaded into the Timer 2 reload registers
(TMR2RLH:TMR2RLL) and the TF2H flag is set (triggering an interrupt if Timer 2 interrupts are enabled).
By recording the difference between two successive timer capture values, the Comparator 0 or SmaRTClock period can be determined with respect to the Timer 2 clock. The Timer 2 clock should be much faster
than the capture clock to achieve an accurate reading.
For example, if T2ML = 1b, T2XCLK1 = 0b, and TF2CEN = 1b, Timer 2 will clock every SYSCLK and capture every SmaRTClock clock divided by 8. If the SYSCLK is 24.5 MHz and the difference between two
successive captures is 5984, then the SmaRTClock clock is as follows:
24.5 MHz/(5984/8) = 0.032754 MHz or 32.754 kHz.
This mode allows software to determine the exact SmaRTClock frequency in self-oscillate mode and the
time between consecutive Comparator 0 rising edges, which is useful for detecting changes in the capacitance of a Touch Sense Switch.
T2XCLK[1:0]
CKCON
X0
Comparator 0
01
SmaRTClock/8
11
T2XCLK1
Comparator 0
TR2
TCLK
TMR2L
TMR2H
Capture
1
SYSCLK
SmaRTClock/8
0
TF2CEN
TMR2RLL TMR2RLH
TMR2CN
SYSCLK/12
TTTTTTSS
3 3 2 2 1 0CC
MMMMMM A A
HLHL
1 0
0
TF2H
TF2L
TF2LEN
TF2CEN
T2SPLIT
TR2
T2XCLK1
T2XCLK0
Interrupt
1
Figure 27.6. Timer 2 Capture Mode Block Diagram
Rev. 1.3
347
Si1000/1/2/3/4/5
SFR Definition 27.8. TMR2CN: Timer 2 Control
Bit
7
6
5
4
3
2
Name
TF2H
TF2L
TF2LEN
TF2CEN
T2SPLIT
TR2
T2XCLK[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xC8; Bit-Addressable
Bit
Name
7
TF2H
1
0
0
0
Function
Timer 2 High Byte Overflow Flag.
Set by hardware when the Timer 2 high byte overflows from 0xFF to 0x00. In 16 bit
mode, this will occur when Timer 2 overflows from 0xFFFF to 0x0000. When the
Timer 2 interrupt is enabled, setting this bit causes the CPU to vector to the
Timer 2 interrupt service routine. This bit is not automatically cleared by hardware.
6
TF2L
Timer 2 Low Byte Overflow Flag.
Set by hardware when the Timer 2 low byte overflows from 0xFF to 0x00. TF2L will
be set when the low byte overflows regardless of the Timer 2 mode. This bit is not
automatically cleared by hardware.
5
TF2LEN
Timer 2 Low Byte Interrupt Enable.
When set to 1, this bit enables Timer 2 Low Byte interrupts. If Timer 2 interrupts
are also enabled, an interrupt will be generated when the low byte of Timer 2 overflows.
4
TF2CEN
Timer 2 Capture Enable.
When set to 1, this bit enables Timer 2 Capture Mode.
3
T2SPLIT
Timer 2 Split Mode Enable.
When set to 1, Timer 2 operates as two 8-bit timers with auto-reload. Otherwise,
Timer 2 operates in 16-bit auto-reload mode.
2
TR2
Timer 2 Run Control.
Timer 2 is enabled by setting this bit to 1. In 8-bit mode, this bit enables/disables
TMR2H only; TMR2L is always enabled in split mode.
1:0
T2XCLK[1:0]
Timer 2 External Clock Select.
This bit selects the “external” and “capture trigger” clock sources for Timer 2. If
Timer 2 is in 8-bit mode, this bit selects the “external” clock source for both timer
bytes. Timer 2 Clock Select bits (T2MH and T2ML in register CKCON) may still be
used to select between the “external” clock and the system clock for either timer.
Note: External clock sources are synchronized with the system clock.
00: External Clock is SYSCLK/12. Capture trigger is SmaRTClock/8.
01: External Clock is Comparator 0. Capture trigger is SmaRTClock/8.
10: External Clock is SYSCLK/12. Capture trigger is Comparator 0.
11: External Clock is SmaRTClock/8. Capture trigger is Comparator 0.
348
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 27.9. TMR2RLL: Timer 2 Reload Register Low Byte
Bit
7
6
5
4
3
Name
TMR2RLL[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xCA
Bit
Name
7:0
2
1
0
0
0
0
2
1
0
0
0
0
Function
TMR2RLL[7:0] Timer 2 Reload Register Low Byte.
TMR2RLL holds the low byte of the reload value for Timer 2.
SFR Definition 27.10. TMR2RLH: Timer 2 Reload Register High Byte
Bit
7
6
5
4
3
Name
TMR2RLH[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xCB
Bit
Name
0
Function
7:0 TMR2RLH[7:0] Timer 2 Reload Register High Byte.
TMR2RLH holds the high byte of the reload value for Timer 2.
Rev. 1.3
349
Si1000/1/2/3/4/5
SFR Definition 27.11. TMR2L: Timer 2 Low Byte
Bit
7
6
5
4
3
Name
TMR2L[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xCC
Bit
Name
7:0
2
1
0
0
0
0
Function
TMR2L[7:0] Timer 2 Low Byte.
In 16-bit mode, the TMR2L register contains the low byte of the 16-bit Timer 2. In 8bit mode, TMR2L contains the 8-bit low byte timer value.
SFR Definition 27.12. TMR2H Timer 2 High Byte
Bit
7
6
5
4
3
Name
TMR2H[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0xCD
Bit
Name
7:0
0
2
1
0
0
0
0
Function
TMR2H[7:0] Timer 2 Low Byte.
In 16-bit mode, the TMR2H register contains the high byte of the 16-bit Timer 2. In 8bit mode, TMR2H contains the 8-bit high byte timer value.
350
Rev. 1.3
Si1000/1/2/3/4/5
27.3. Timer 3
Timer 3 is a 16-bit timer formed by two 8-bit SFRs: TMR3L (low byte) and TMR3H (high byte). Timer 3 may
operate in 16-bit auto-reload mode or (split) 8-bit auto-reload mode. The T3SPLIT bit (TMR3CN.3) defines
the Timer 3 operation mode. Timer 3 can also be used in Capture Mode to measure the external oscillator
source or the Comparator 1 period with respect to another oscillator. The ability to measure the
Comparator 1 period with respect to the system clock is makes using Touch Sense Switches very easy.
Timer 3 may be clocked by the system clock, the system clock divided by 12, external oscillator source
divided by 8, or Comparator 1 output. The external oscillator source divided by 8 and Comparator 1 output
is synchronized with the system clock.
27.3.1. 16-bit Timer with Auto-Reload
When T3SPLIT (TMR3CN.3) is zero, Timer 3 operates as a 16-bit timer with auto-reload. Timer 3 can be
clocked by SYSCLK, SYSCLK divided by 12, external oscillator clock source divided by 8, or Comparator 1
output. As the 16-bit timer register increments and overflows from 0xFFFF to 0x0000, the 16-bit value in
the Timer 3 reload registers (TMR3RLH and TMR3RLL) is loaded into the Timer 3 register as shown in
Figure 27.7, and the Timer 3 High Byte Overflow Flag (TMR3CN.7) is set. If Timer 3 interrupts are enabled
(if EIE1.7 is set), an interrupt will be generated on each Timer 3 overflow. Additionally, if Timer 3 interrupts
are enabled and the TF3LEN bit is set (TMR3CN.5), an interrupt will be generated each time the lower 8
bits (TMR3L) overflow from 0xFF to 0x00.
CKCON
TTTTTTSS
3 3 2 2 1 0CC
MMMMMM A A
HLHL
1 0
T3XCLK[1:0]
SYSCLK / 12
00
External Clock / 8
01
SYSCLK / 12
10
Comparator 1
11
To ADC
0
TCLK
TMR3L
TMR3H
TMR3CN
TR3
1
SYSCLK
TMR3RLL TMR3RLH
TF3H
TF3L
TF3LEN
TF3CEN
T3SPLIT
TR3
T3XCLK1
T3XCLK0
Interrupt
Reload
Figure 27.7. Timer 3 16-Bit Mode Block Diagram
27.3.2. 8-bit Timers with Auto-Reload
When T3SPLIT is set, Timer 3 operates as two 8-bit timers (TMR3H and TMR3L). Both 8-bit timers operate in auto-reload mode as shown in Figure 27.8. TMR3RLL holds the reload value for TMR3L; TMR3RLH
holds the reload value for TMR3H. The TR3 bit in TMR3CN handles the run control for TMR3H. TMR3L is
always running when configured for 8-bit Mode.
Rev. 1.3
351
Si1000/1/2/3/4/5
Each 8-bit timer may be configured to use SYSCLK, SYSCLK divided by 12, the external oscillator clock
source divided by 8, or Comparator 1. The Timer 3 Clock Select bits (T3MH and T3ML in CKCON) select
either SYSCLK or the clock defined by the Timer 3 External Clock Select bits (T3XCLK[1:0] in TMR3CN),
as follows:
T3MH
T3XCLK[1:0] TMR3H Clock
Source
T3ML
T3XCLK[1:0] TMR3L Clock
Source
0
00
SYSCLK / 12
0
00
SYSCLK / 12
0
01
External Clock / 8
0
01
External Clock / 8
0
10
SYSCLK / 12
0
10
SYSCLK / 12
0
11
Comparator 1
0
11
Comparator 1
1
X
SYSCLK
1
X
SYSCLK
The TF3H bit is set when TMR3H overflows from 0xFF to 0x00; the TF3L bit is set when TMR3L overflows
from 0xFF to 0x00. When Timer 3 interrupts are enabled, an interrupt is generated each time TMR3H overflows. If Timer 3 interrupts are enabled and TF3LEN (TMR3CN.5) is set, an interrupt is generated each
time either TMR3L or TMR3H overflows. When TF3LEN is enabled, software must check the TF3H and
TF3L flags to determine the source of the Timer 3 interrupt. The TF3H and TF3L interrupt flags are not
cleared by hardware and must be manually cleared by software.
CKCON
TT T TT TSS
3 3 2 2 1 0CC
MMMMMM A A
HLHL
1 0
T3XCLK[1:0]
SYSCLK / 12
00
External Clock / 8
01
SYSCLK / 12
10
TMR3RLH
Reload
0
TCLK
TR3
TMR3H
Comparator 1
11
TMR3RLL
SYSCLK
Reload
TMR3CN
1
TF3H
TF3L
TF3LEN
TF3CEN
T3SPLIT
TR3
T3XCLK1
T3XCLK0
1
TCLK
TMR3L
To ADC
0
Figure 27.8. Timer 3 8-Bit Mode Block Diagram.
352
Rev. 1.3
Interrupt
Si1000/1/2/3/4/5
27.3.3. Comparator 1/External Oscillator Capture Mode
The Capture Mode in Timer 3 allows either Comparator 1 or the external oscillator period to be measured
against the system clock or the system clock divided by 12. Comparator 1 and the external oscillator
period can also be compared against each other.
Setting TF3CEN to 1 enables the Comparator 1/External Oscillator Capture Mode for Timer 3. In this
mode, T3SPLIT should be set to 0, as the full 16-bit timer is used.
When Capture Mode is enabled, a capture event will be generated either every Comparator 1 rising edge
or every 8 external clock cycles, depending on the T3XCLK1 setting. When the capture event occurs, the
contents of Timer 3 (TMR3H:TMR3L) are loaded into the Timer 3 reload registers (TMR3RLH:TMR3RLL)
and the TF3H flag is set (triggering an interrupt if Timer 3 interrupts are enabled). By recording the difference between two successive timer capture values, the Comparator 1 or external clock period can be
determined with respect to the Timer 3 clock. The Timer 3 clock should be much faster than the capture
clock to achieve an accurate reading.
For example, if T3ML = 1b, T3XCLK1 = 0b, and TF3CEN = 1b, Timer 3 will clock every SYSCLK and capture every Comparator 1 rising edge. If SYSCLK is 24.5 MHz and the difference between two successive
captures is 350 counts, then the Comparator 1 period is:
350 x (1 / 24.5 MHz) = 14.2 µs.
This mode allows software to determine the exact frequency of the external oscillator in C and RC mode or
the time between consecutive Comparator 0 rising edges, which is useful for detecting changes in the
capacitance of a Touch Sense Switch.
T 3 X C L K [1 :0 ]
CKCON
SYSCLK / 12
00
E xte rn a l C lo ck / 8
01
SYSCLK / 12
10
C o m p a ra to r 1
11
T
3
M
H
T
3
M
L
T
2
M
H
T T T S S
2 1 0 C C
MMM A A
1 0
L
0
TR3
SYSCLK
0
E xte rn a l C lo ck / 8
1
TM R3H
TF3CEN
TM R3RLL
TM R3RLH
TMR3CN
C o m p a ra to r 1
TM R3L
C a p tu re
1
T3XCLK1
TC LK
T F 3H
TF3L
T F 3 LE N
TF3CEN
T 3 S P LIT
TR3
T3XCLK1
T3XCLK0
In te rru p t
Figure 27.9. Timer 3 Capture Mode Block Diagram
Rev. 1.3
353
Si1000/1/2/3/4/5
SFR Definition 27.13. TMR3CN: Timer 3 Control
Bit
7
6
5
4
3
2
Name
TF3H
TF3L
TF3LEN
TF3CEN
T3SPLIT
TR3
T3XCLK[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0x91
Bit
Name
7
TF3H
1
0
0
0
Function
Timer 3 High Byte Overflow Flag.
Set by hardware when the Timer 3 high byte overflows from 0xFF to 0x00. In 16 bit
mode, this will occur when Timer 3 overflows from 0xFFFF to 0x0000. When the
Timer 3 interrupt is enabled, setting this bit causes the CPU to vector to the Timer 3
interrupt service routine. This bit is not automatically cleared by hardware.
6
TF3L
Timer 3 Low Byte Overflow Flag.
Set by hardware when the Timer 3 low byte overflows from 0xFF to 0x00. TF3L will
be set when the low byte overflows regardless of the Timer 3 mode. This bit is not
automatically cleared by hardware.
5
TF3LEN
Timer 3 Low Byte Interrupt Enable.
When set to 1, this bit enables Timer 3 Low Byte interrupts. If Timer 3 interrupts are
also enabled, an interrupt will be generated when the low byte of Timer 3 overflows.
4
TF3CEN
Timer 3 Comparator 1/External Oscillator Capture Enable.
When set to 1, this bit enables Timer 3 Capture Mode.
3
T3SPLIT
Timer 3 Split Mode Enable.
When this bit is set, Timer 3 operates as two 8-bit timers with auto-reload.
0: Timer 3 operates in 16-bit auto-reload mode.
1: Timer 3 operates as two 8-bit auto-reload timers.
2
TR3
Timer 3 Run Control.
Timer 3 is enabled by setting this bit to 1. In 8-bit mode, this bit enables/disables
TMR3H only; TMR3L is always enabled in split mode.
1:0
T3XCLK[1:0] Timer 3 External Clock Select.
This bit selects the “external” and “capture trigger” clock sources for Timer 3. If
Timer 3 is in 8-bit mode, this bit selects the “external” clock source for both timer
bytes. Timer 3 Clock Select bits (T3MH and T3ML in register CKCON) may still be
used to select between the “external” clock and the system clock for either timer.
Note: External clock sources are synchronized with the system clock.
00: External Clock is SYSCLK /12. Capture trigger is Comparator 1.
01: External Clock is External Oscillator/8. Capture trigger is Comparator 1.
10: External Clock is SYSCLK/12. Capture trigger is External Oscillator/8.
11: External Clock is Comparator 1. Capture trigger is External Oscillator/8.
354
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 27.14. TMR3RLL: Timer 3 Reload Register Low Byte
Bit
7
6
5
4
3
Name
TMR3RLL[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0x92
Bit
Name
7:0
2
1
0
0
0
0
2
1
0
0
0
0
Function
TMR3RLL[7:0] Timer 3 Reload Register Low Byte.
TMR3RLL holds the low byte of the reload value for Timer 3.
SFR Definition 27.15. TMR3RLH: Timer 3 Reload Register High Byte
Bit
7
6
5
4
3
Name
TMR3RLH[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0x93
Bit
Name
0
Function
7:0 TMR3RLH[7:0] Timer 3 Reload Register High Byte.
TMR3RLH holds the high byte of the reload value for Timer 3.
Rev. 1.3
355
Si1000/1/2/3/4/5
SFR Definition 27.16. TMR3L: Timer 3 Low Byte
Bit
7
6
5
4
3
Name
TMR3L[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0x94
Bit
Name
7:0
TMR3L[7:0]
2
1
0
0
0
0
Function
Timer 3 Low Byte.
In 16-bit mode, the TMR3L register contains the low byte of the 16-bit Timer 3. In
8-bit mode, TMR3L contains the 8-bit low byte timer value.
SFR Definition 27.17. TMR3H Timer 3 High Byte
Bit
7
6
5
4
3
Name
TMR3H[7:0]
Type
R/W
Reset
0
0
0
0
SFR Page = 0x0; SFR Address = 0x95
Bit
Name
7:0
TMR3H[7:0]
0
2
1
0
0
0
0
Function
Timer 3 High Byte.
In 16-bit mode, the TMR3H register contains the high byte of the 16-bit Timer 3. In
8-bit mode, TMR3H contains the 8-bit high byte timer value.
356
Rev. 1.3
Si1000/1/2/3/4/5
28. Programmable Counter Array
The Programmable Counter Array (PCA0) provides enhanced timer functionality while requiring less CPU
intervention than the standard 8051 counter/timers. The PCA consists of a dedicated 16-bit counter/timer
and six 16-bit capture/compare modules. Each capture/compare module has its own associated I/O line
(CEXn) which is routed through the Crossbar to Port I/O when enabled. The counter/timer is driven by a
programmable timebase that can select between the following sources: system clock, system clock divided
by four, system clock divided by twelve, the external oscillator clock source divided by 8, Timer 0 overflows, or an external clock signal on the ECI input pin. Each capture/compare module may be configured to
operate independently in one of six modes: Edge-Triggered Capture, Software Timer, High-Speed Output,
Frequency Output, 8 to 11-Bit PWM, or 16-Bit PWM (each mode is described in Section
“28.3. Capture/Compare Modules” on page 360). The external oscillator clock option is ideal for real-time
clock (RTC) functionality, allowing the PCA to be clocked by a precision external oscillator while the internal oscillator drives the system clock. The PCA is configured and controlled through the system controller's
Special Function Registers. The PCA block diagram is shown in Figure 28.1
Important Note: The PCA Module 5 may be used as a watchdog timer (WDT), and is enabled in this mode
following a system reset. Access to certain PCA registers is restricted while WDT mode is enabled.
See Section 28.4 for details.
SYSCLK/12
SYSCLK/4
Timer 0 Overflow
ECI
SYSCLK
PCA
CLOCK
MUX
16-Bit Counter/Timer
External Clock/8
Capture/Compare
Module 0
Capture/Compare
Module 1
Capture/Compare
Module 2
Capture/Compare
Module 3
Capture/Compare
Module 4
Capture/Compare
Module 5 / WDT
CEX5
CEX4
CEX3
CEX2
CEX1
CEX0
ECI
Crossbar
Port I/O
Figure 28.1. PCA Block Diagram
Rev. 1.3
357
Si1000/1/2/3/4/5
28.1. PCA Counter/Timer
The 16-bit PCA counter/timer consists of two 8-bit SFRs: PCA0L and PCA0H. PCA0H is the high byte
(MSB) of the 16-bit counter/timer and PCA0L is the low byte (LSB). Reading PCA0L automatically latches
the value of PCA0H into a “snapshot” register; the following PCA0H read accesses this “snapshot” register.
Reading the PCA0L Register first guarantees an accurate reading of the entire 16-bit PCA0 counter.
Reading PCA0H or PCA0L does not disturb the counter operation. The CPS2–CPS0 bits in the PCA0MD
register select the timebase for the counter/timer as shown in Table 28.1.
When the counter/timer overflows from 0xFFFF to 0x0000, the Counter Overflow Flag (CF) in PCA0MD is
set to logic 1 and an interrupt request is generated if CF interrupts are enabled. Setting the ECF bit in
PCA0MD to logic 1 enables the CF flag to generate an interrupt request. The CF bit is not automatically
cleared by hardware when the CPU vectors to the interrupt service routine, and must be cleared by software. Clearing the CIDL bit in the PCA0MD register allows the PCA to continue normal operation while the
CPU is in Idle mode.
Table 28.1. PCA Timebase Input Options
CPS2
CPS1
CPS0
Timebase
0
0
0
System clock divided by 12
0
0
1
System clock divided by 4
0
1
0
Timer 0 overflow
0
1
1
High-to-low transitions on ECI (max rate = system clock divided
by 4)
1
0
0
System clock
1
0
1
External oscillator source divided by 8*
1
1
0
Reserved
1
1
1
Reserved
Note: External oscillator source divided by 8 is synchronized with the system clock.
IDLE
PCA0MD
C
I
D
L
WW
D D
T L
E C
K
C
P
S
2
C
P
S
1
CE
PC
S F
0
PCA0CN
CCC
FRC
F
5
C
C
F
4
C
C
F
3
C
C
F
2
C
C
F
1
C
C
F
0
To SFR Bus
PCA0L
read
Snapshot
Register
SYSCLK/12
SYSCLK/4
Timer 0 Overflow
ECI
SYSCLK
External Clock/8
000
001
010
0
1
PCA0H
PCA0L
Overflow
011
100
To PCA Modules
101
Figure 28.2. PCA Counter/Timer Block Diagram
358
To PCA Interrupt System
CF
Rev. 1.3
Si1000/1/2/3/4/5
28.2. PCA0 Interrupt Sources
Figure 28.3 shows a diagram of the PCA interrupt tree. There are eight independent event flags that can
be used to generate a PCA0 interrupt. They are: the main PCA counter overflow flag (CF), which is set
upon a 16-bit overflow of the PCA0 counter, an intermediate overflow flag (COVF), which can be set on an
overflow from the 8th, 9th, 10th, or 11th bit of the PCA0 counter, and the individual flags for each PCA
channel (CCF0, CCF1, CCF2, CCF3, CCF4, and CCF5), which are set according to the operation mode of
that module. These event flags are always set when the trigger condition occurs. Each of these flags can
be individually selected to generate a PCA0 interrupt, using the corresponding interrupt enable flag (ECF
for CF, ECOV for COVF, and ECCFn for each CCFn). PCA0 interrupts must be globally enabled before any
individual interrupt sources are recognized by the processor. PCA0 interrupts are globally enabled by setting the EA bit and the EPCA0 bit to logic 1.
(for n = 0 to 5)
PCA0CPMn
PCA0CN
P ECCMT P E
WC A A AOWC
MOPP TGMC
1 MP N n n n F
6 n n n
n
n
CCCCCCCC
FRCCCCCC
FFFFFF
5 4 3 2 1 0
PCA0MD
C WW
I DD
DT L
LEC
K
PCA0PWM
A CE
ROC
S VO
EFV
L
CCCE
PPPC
SSSF
2 1 0
C
L
S
E
L
1
PCA Counter/Timer 8, 9,
10 or 11-bit Overflow
C
L
S
E
L
0
Set 8, 9, 10, or 11 bit Operation
0
PCA Counter/Timer 16bit Overflow
0
1
1
ECCF0
PCA Module 0
(CCF0)
EPCA0
EA
0
0
0
1
1
1
Interrupt
Priority
Decoder
ECCF1
0
PCA Module 1
(CCF1)
1
ECCF2
0
PCA Module 2
(CCF2)
1
ECCF3
0
PCA Module 3
(CCF3)
1
ECCF4
0
PCA Module 4
(CCF4)
1
ECCF5
PCA Module 5
(CCF5)
0
1
Figure 28.3. PCA Interrupt Block Diagram
Rev. 1.3
359
Si1000/1/2/3/4/5
28.3. Capture/Compare Modules
Each module can be configured to operate independently in one of six operation modes: edge-triggered
capture, software timer, high speed output, frequency output, 8 to 11-bit pulse width modulator, or 16-bit
pulse width modulator. Each module has Special Function Registers (SFRs) associated with it in the CIP51 system controller. These registers are used to exchange data with a module and configure the module's
mode of operation. Table 28.2 summarizes the bit settings in the PCA0CPMn and PCA0PWM registers
used to select the PCA capture/compare module’s operating mode. Note that all modules set to use 8, 9,
10, or 11-bit PWM mode must use the same cycle length (8-11 bits). Setting the ECCFn bit in a
PCA0CPMn register enables the module's CCFn interrupt.
Table 28.2. PCA0CPM and PCA0PWM Bit Settings for PCA Capture/Compare Modules
Operational Mode
PCA0CPMn
PCA0PWM
Bit Number
7 6 5 4 3 2 1 0 7 6 5 4-2
Capture triggered by positive edge on CEXn
X X 1 0 0 0 0 A 0 X B XXX XX
Capture triggered by negative edge on CEXn
X X 0 1 0 0 0 A 0 X B XXX XX
Capture triggered by any transition on CEXn
X X 1 1 0 0 0 A 0 X B XXX XX
Software Timer
X C 0 0 1 0 0 A 0 X B XXX XX
High Speed Output
X C 0 0 1 1 0 A 0 X B XXX XX
Frequency Output
X C 0 0 0 1 1 A 0 X B XXX XX
8-Bit Pulse Width Modulator (Note 7)
0 C 0 0 E 0 1 A 0 X B XXX 00
9-Bit Pulse Width Modulator (Note 7)
0 C 0 0 E 0 1 A D X B XXX 01
10-Bit Pulse Width Modulator (Note 7)
0 C 0 0 E 0 1 A D X B XXX 10
11-Bit Pulse Width Modulator (Note 7)
0 C 0 0 E 0 1 A D X B XXX 11
16-Bit Pulse Width Modulator
1 C 0 0 E 0 1 A 0 X B XXX XX
1–0
Notes:
1. X = Don’t Care (no functional difference for individual module if 1 or 0).
2. A = Enable interrupts for this module (PCA interrupt triggered on CCFn set to 1).
3. B = Enable 8th, 9th, 10th or 11th bit overflow interrupt (Depends on setting of CLSEL[1:0]).
4. C = When set to 0, the digital comparator is off. For high speed and frequency output modes, the
associated pin will not toggle. In any of the PWM modes, this generates a 0% duty cycle (output = 0).
5. D = Selects whether the Capture/Compare register (0) or the Auto-Reload register (1) for the associated
channel is accessed via addresses PCA0CPHn and PCA0CPLn.
6. E = When set, a match event will cause the CCFn flag for the associated channel to be set.
7. All modules set to 8, 9, 10 or 11-bit PWM mode use the same cycle length setting.
360
Rev. 1.3
Si1000/1/2/3/4/5
28.3.1. Edge-triggered Capture Mode
In this mode, a valid transition on the CEXn pin causes the PCA to capture the value of the PCA
counter/timer and load it into the corresponding module's 16-bit capture/compare register (PCA0CPLn and
PCA0CPHn). The CAPPn and CAPNn bits in the PCA0CPMn register are used to select the type of transition that triggers the capture: low-to-high transition (positive edge), high-to-low transition (negative edge),
or either transition (positive or negative edge). When a capture occurs, the Capture/Compare Flag (CCFn)
in PCA0CN is set to logic 1. An interrupt request is generated if the CCFn interrupt for that module is
enabled. The CCFn bit is not automatically cleared by hardware when the CPU vectors to the interrupt service routine, and must be cleared by software. If both CAPPn and CAPNn bits are set to logic 1, then the
state of the Port pin associated with CEXn can be read directly to determine whether a rising-edge or falling-edge caused the capture.
PCA Interrupt
PCA0CPMn
P ECCMT P E
WC A A AOWC
MOPP TGMC
1 MP N n n n F
6 n n n
n
n
0 0 0 x
0
Port I/O
Crossbar
CEXn
CCC
CCC
FFF
2 1 0
(to CCFn)
x x
PCA0CN
CC
FR
1
PCA0CPLn
PCA0CPHn
Capture
0
1
PCA
Timebase
PCA0L
PCA0H
Figure 28.4. PCA Capture Mode Diagram
Note: The CEXn input signal must remain high or low for at least 2 system clock cycles to be recognized by the
hardware.
Rev. 1.3
361
Si1000/1/2/3/4/5
28.3.2. Software Timer (Compare) Mode
In Software Timer mode, the PCA counter/timer value is compared to the module's 16-bit capture/compare
register (PCA0CPHn and PCA0CPLn). When a match occurs, the Capture/Compare Flag (CCFn) in
PCA0CN is set to logic 1. An interrupt request is generated if the CCFn interrupt for that module is
enabled. The CCFn bit is not automatically cleared by hardware when the CPU vectors to the interrupt service routine, and must be cleared by software. Setting the ECOMn and MATn bits in the PCA0CPMn register enables Software Timer mode.
Important Note About Capture/Compare Registers: When writing a 16-bit value to the PCA0 Capture/Compare registers, the low byte should always be written first. Writing to PCA0CPLn clears the
ECOMn bit to 0; writing to PCA0CPHn sets ECOMn to 1.
Write to
PCA0CPLn
0
ENB
Reset
Write to
PCA0CPHn
PCA Interrupt
ENB
1
PCA0CPMn
P ECCMT P E
WC A A AOWC
MOPP TGMC
1 MP N n n n F
6 n n n
n
n
x
0 0
PCA0CN
PCA0CPLn
CC
FR
PCA0CPHn
0 0 x
Enable
16-bit Comparator
PCA
Timebase
PCA0L
Match
PCA0H
Figure 28.5. PCA Software Timer Mode Diagram
362
CCC
CCC
FFF
2 1 0
Rev. 1.3
0
1
Si1000/1/2/3/4/5
28.3.3. High-Speed Output Mode
In High-Speed Output mode, a module’s associated CEXn pin is toggled each time a match occurs
between the PCA Counter and the module's 16-bit capture/compare register (PCA0CPHn and
PCA0CPLn). When a match occurs, the Capture/Compare Flag (CCFn) in PCA0CN is set to logic 1. An
interrupt request is generated if the CCFn interrupt for that module is enabled. The CCFn bit is not automatically cleared by hardware when the CPU vectors to the interrupt service routine, and must be cleared
by software. Setting the TOGn, MATn, and ECOMn bits in the PCA0CPMn register enables the HighSpeed Output mode. If ECOMn is cleared, the associated pin will retain its state, and not toggle on the next
match event.
Important Note About Capture/Compare Registers: When writing a 16-bit value to the PCA0 Capture/Compare registers, the low byte should always be written first. Writing to PCA0CPLn clears the
ECOMn bit to 0; writing to PCA0CPHn sets ECOMn to 1.
Write to
PCA0CPLn
0
ENB
Reset
Write to
PCA0CPHn
PCA0CPMn
P ECCMT P E
WC A A AOWC
MOPP TGMC
1 MPN n n n F
6 n n n
n
n
ENB
1
x
0 0
0 x
PCA Interrupt
PCA0CN
PCA0CPLn
Enable
CC
FR
PCA0CPHn
16-bit Comparator
Match
0
1
Toggle
PCA
Timebase
CCC
CCC
FFF
2 1 0
TOGn
0 CEXn
1
PCA0L
Crossbar
Port I/O
PCA0H
Figure 28.6. PCA High-Speed Output Mode Diagram
Rev. 1.3
363
Si1000/1/2/3/4/5
28.3.4. Frequency Output Mode
Frequency Output Mode produces a programmable-frequency square wave on the module’s associated
CEXn pin. The capture/compare module high byte holds the number of PCA clocks to count before the output is toggled. The frequency of the square wave is then defined by Equation 28.1.
F PCA
F CEXn = ----------------------------------------2  PCA0CPHn
Note: A value of 0x00 in the PCA0CPHn register is equal to 256 for this equation.
Equation 28.1. Square Wave Frequency Output
Where FPCA is the frequency of the clock selected by the CPS2–0 bits in the PCA mode register,
PCA0MD. The lower byte of the capture/compare module is compared to the PCA counter low byte; on a
match, CEXn is toggled and the offset held in the high byte is added to the matched value in PCA0CPLn.
Frequency Output Mode is enabled by setting the ECOMn, TOGn, and PWMn bits in the PCA0CPMn register. Note that the MATn bit should normally be set to 0 in this mode. If the MATn bit is set to 1, the CCFn
flag for the channel will be set when the 16-bit PCA0 counter and the 16-bit capture/compare register for
the channel are equal.
Write to
PCA0CPLn
0
ENB
Reset
PCA0CPMn
Write to
PCA0CPHn
ENB
1
P ECCMT P E
WC A A AOWC
MOPP TGMC
1 MP N n n n F
6 n n n
n
n
x
0 0 0
PCA0CPLn
8-bit Adder
Adder
Enable
Toggle
x
Enable
PCA Timebase
8-bit
Comparator
PCA0CPHn
TOGn
match
0 CEXn
1
Crossbar
Port I/O
PCA0L
Figure 28.7. PCA Frequency Output Mode
28.3.5. 8-Bit, 9-Bit, 10-Bit and 11-Bit Pulse Width Modulator Modes
Each module can be used independently to generate a pulse width modulated (PWM) output on its associated CEXn pin. The frequency of the output is dependent on the timebase for the PCA counter/timer, and
the setting of the PWM cycle length (8, 9, 10 or 11-bits). For backwards-compatibility with the 8-bit PWM
mode available on other devices, the 8-bit PWM mode operates slightly different than 9, 10 and 11-bit
PWM modes. It is important to note that all channels configured for 8/9/10/11-bit PWM mode will use
the same cycle length. It is not possible to configure one channel for 8-bit PWM mode and another for 11bit mode (for example). However, other PCA channels can be configured to Pin Capture, High-Speed Output, Software Timer, Frequency Output, or 16-bit PWM mode independently.
364
Rev. 1.3
Si1000/1/2/3/4/5
28.3.5.1. 8-Bit Pulse Width Modulator Mode
The duty cycle of the PWM output signal in 8-bit PWM mode is varied using the module's PCA0CPLn capture/compare register. When the value in the low byte of the PCA counter/timer (PCA0L) is equal to the
value in PCA0CPLn, the output on the CEXn pin will be set. When the count value in PCA0L overflows, the
CEXn output will be reset (see Figure 28.8). Also, when the counter/timer low byte (PCA0L) overflows from
0xFF to 0x00, PCA0CPLn is reloaded automatically with the value stored in the module’s capture/compare
high byte (PCA0CPHn) without software intervention. Setting the ECOMn and PWMn bits in the
PCA0CPMn register, and setting the CLSEL bits in register PCA0PWM to 00b enables 8-Bit Pulse Width
Modulator mode. If the MATn bit is set to 1, the CCFn flag for the module will be set each time an 8-bit
comparator match (rising edge) occurs. The COVF flag in PCA0PWM can be used to detect the overflow
(falling edge), which will occur every 256 PCA clock cycles. The duty cycle for 8-Bit PWM Mode is given in
Equation 28.2.
Important Note About Capture/Compare Registers: When writing a 16-bit value to the PCA0 Capture/Compare registers, the low byte should always be written first. Writing to PCA0CPLn clears the
ECOMn bit to 0; writing to PCA0CPHn sets ECOMn to 1.
 256 – PCA0CPHn 
Duty Cycle = --------------------------------------------------256
Equation 28.2. 8-Bit PWM Duty Cycle
Using Equation 28.2, the largest duty cycle is 100% (PCA0CPHn = 0), and the smallest duty cycle is
0.39% (PCA0CPHn = 0xFF). A 0% duty cycle may be generated by clearing the ECOMn bit to 0.
Write to
PCA0CPLn
0
ENB
Reset
PCA0CPHn
Write to
PCA0CPHn
ENB
COVF
1
PCA0PWM
A
R
S
E
L
EC
CO
OV
VF
0 x
C
L
S
E
L
1
PCA0CPMn
C
L
S
E
L
0
0 0
P ECCMT P E
WC A A AOWC
MOPP TGMC
1 MP N n n n F
6 n n n
n
n
0
0 0 x 0
PCA0CPLn
x
Enable
8-bit
Comparator
match
S
R
PCA Timebase
PCA0L
SET
CLR
Q
CEXn
Crossbar
Port I/O
Q
Overflow
Figure 28.8. PCA 8-Bit PWM Mode Diagram
Rev. 1.3
365
Si1000/1/2/3/4/5
28.3.5.2. 9/10/11-bit Pulse Width Modulator Mode
The duty cycle of the PWM output signal in 9/10/11-bit PWM mode should be varied by writing to an “AutoReload” Register, which is dual-mapped into the PCA0CPHn and PCA0CPLn register locations. The data
written to define the duty cycle should be right-justified in the registers. The auto-reload registers are
accessed (read or written) when the bit ARSEL in PCA0PWM is set to 1. The capture/compare registers
are accessed when ARSEL is set to 0.
When the least-significant N bits of the PCA0 counter match the value in the associated module’s capture/compare register (PCA0CPn), the output on CEXn is asserted high. When the counter overflows from
the Nth bit, CEXn is asserted low (see Figure 28.9). Upon an overflow from the Nth bit, the COVF flag is
set, and the value stored in the module’s auto-reload register is loaded into the capture/compare register.
The value of N is determined by the CLSEL bits in register PCA0PWM.
The 9, 10 or 11-bit PWM mode is selected by setting the ECOMn and PWMn bits in the PCA0CPMn register, and setting the CLSEL bits in register PCA0PWM to the desired cycle length (other than 8-bits). If the
MATn bit is set to 1, the CCFn flag for the module will be set each time a comparator match (rising edge)
occurs. The COVF flag in PCA0PWM can be used to detect the overflow (falling edge), which will occur
every 512 (9-bit), 1024 (10-bit) or 2048 (11-bit) PCA clock cycles. The duty cycle for 9/10/11-Bit PWM
Mode is given in Equation 28.2, where N is the number of bits in the PWM cycle.
Important Note About PCA0CPHn and PCA0CPLn Registers: When writing a 16-bit value to the
PCA0CPn registers, the low byte should always be written first. Writing to PCA0CPLn clears the ECOMn
bit to 0; writing to PCA0CPHn sets ECOMn to 1.
 2 N – PCA0CPn Duty Cycle = ------------------------------------------2N
Equation 28.3. 9, 10, and 11-Bit PWM Duty Cycle
A 0% duty cycle may be generated by clearing the ECOMn bit to 0.
Write to
PCA0CPLn
0
R/W when
ARSEL = 1
ENB
Reset
Write to
PCA0CPHn
(Auto-Reload)
PCA0PWM
PCA0CPH:Ln
A
R
S
E
L
(right-justified)
ENB
1
C
L
S
E
L
1
EC
CO
OV
VF
PCA0CPMn
P ECCMT P E
WC A A AOWC
MOPP TGMC
1 MP N n n n F
6 n n n
n
n
0
0 0 x 0
R/W when
ARSEL = 0
C
L
S
E
L
0
x
(Capture/Compare)
Set “N” bits:
01 = 9 bits
10 = 10 bits
11 = 11 bits
PCA0CPH:Ln
(right-justified)
x
Enable
N-bit Comparator
match
S
R
PCA Timebase
SET
CLR
Q
CEXn
Crossbar
Q
PCA0H:L
Overflow of Nth Bit
Figure 28.9. PCA 9, 10 and 11-Bit PWM Mode Diagram
366
Rev. 1.3
Port I/O
Si1000/1/2/3/4/5
28.3.6. 16-Bit Pulse Width Modulator Mode
A PCA module may also be operated in 16-Bit PWM mode. 16-bit PWM mode is independent of the other
(8/9/10/11-bit) PWM modes. In this mode, the 16-bit capture/compare module defines the number of PCA
clocks for the low time of the PWM signal. When the PCA counter matches the module contents, the output on CEXn is asserted high; when the 16-bit counter overflows, CEXn is asserted low. To output a varying duty cycle, new value writes should be synchronized with PCA CCFn match interrupts. 16-Bit PWM
Mode is enabled by setting the ECOMn, PWMn, and PWM16n bits in the PCA0CPMn register. For a varying duty cycle, match interrupts should be enabled (ECCFn = 1 AND MATn = 1) to help synchronize the
capture/compare register writes. If the MATn bit is set to 1, the CCFn flag for the module will be set each
time a 16-bit comparator match (rising edge) occurs. The CF flag in PCA0CN can be used to detect the
overflow (falling edge). The duty cycle for 16-Bit PWM Mode is given by Equation 28.4.
Important Note About Capture/Compare Registers: When writing a 16-bit value to the PCA0 Capture/Compare registers, the low byte should always be written first. Writing to PCA0CPLn clears the
ECOMn bit to 0; writing to PCA0CPHn sets ECOMn to 1.
 65536 – PCA0CPn 
Duty Cycle = ----------------------------------------------------65536
Equation 28.4. 16-Bit PWM Duty Cycle
Using Equation 28.4, the largest duty cycle is 100% (PCA0CPn = 0), and the smallest duty cycle is
0.0015% (PCA0CPn = 0xFFFF). A 0% duty cycle may be generated by clearing the ECOMn bit to 0.
Write to
PCA0CPLn
0
ENB
Reset
Write to
PCA0CPHn
ENB
1
PCA0CPMn
P EC
WCA
MOP
1 MP
6 n n
n
1
C
A
P
N
n
MT P
AOW
TGM
n n n
0 0 x 0
E
C
C
F
n
PCA0CPHn
PCA0CPLn
x
Enable
16-bit Comparator
match
S
R
PCA Timebase
PCA0H
PCA0L
SET
CLR
Q
CEXn
Crossbar
Port I/O
Q
Overflow
Figure 28.10. PCA 16-Bit PWM Mode
Rev. 1.3
367
Si1000/1/2/3/4/5
28.4. Watchdog Timer Mode
A programmable watchdog timer (WDT) function is available through the PCA Module 5. The WDT is used
to generate a reset if the time between writes to the WDT update register (PCA0CPH5) exceed a specified
limit. The WDT can be configured and enabled/disabled as needed by software.
With the WDTE bit set in the PCA0MD register, Module 5 operates as a watchdog timer (WDT). The Module 5 high byte is compared to the PCA counter high byte; the Module 5 low byte holds the offset to be
used when WDT updates are performed. The Watchdog Timer is enabled on reset. Writes to some
PCA registers are restricted while the Watchdog Timer is enabled. The WDT will generate a reset
shortly after code begins execution. To avoid this reset, the WDT should be explicitly disabled (and optionally re-configured and re-enabled if it is used in the system).
28.4.1. Watchdog Timer Operation
While the WDT is enabled:
PCA counter is forced on.
 Writes to PCA0L and PCA0H are not allowed.
 PCA clock source bits (CPS2–CPS0) are frozen.
 PCA Idle control bit (CIDL) is frozen.
 Module 5 is forced into software timer mode.
 Writes to the Module 5 mode register (PCA0CPM5) are disabled.
While the WDT is enabled, writes to the CR bit will not change the PCA counter state; the counter will run
until the WDT is disabled. The PCA counter run control bit (CR) will read zero if the WDT is enabled but
user software has not enabled the PCA counter. If a match occurs between PCA0CPH5 and PCA0H while
the WDT is enabled, a reset will be generated. To prevent a WDT reset, the WDT may be updated with a
write of any value to PCA0CPH5. Upon a PCA0CPH5 write, PCA0H plus the offset held in PCA0CPL5 is
loaded into PCA0CPH5 (See Figure 28.11).

PCA 0M D
C
I
D
L
W
D
T
E
W
D
L
C
K
C
P
S
2
C
P
S
1
C E
P C
S F
0
PCA0CPH 5
Enable
PCA0CPL5
8-bit Adder
W rite to
(PCA0CPH5)
8-bit
Com parator
PCA 0H
M atch
Reset
PCA0L O verflow
Adder
Enable
Figure 28.11. PCA Module 5 with Watchdog Timer Enabled
Note that the 8-bit offset held in PCA0CPH5 is compared to the upper byte of the 16-bit PCA counter. This
offset value is the number of PCA0L overflows before a reset. Up to 256 PCA clocks may pass before the
first PCA0L overflow occurs, depending on the value of the PCA0L when the update is performed. The
total offset is then given (in PCA clocks) by Equation 28.5, where PCA0L is the value of the PCA0L register
at the time of the update.
368
Rev. 1.3
Si1000/1/2/3/4/5
Offset =  256  PCA0CPL5  +  256 – PCA0L 
Equation 28.5. Watchdog Timer Offset in PCA Clocks
The WDT reset is generated when PCA0L overflows while there is a match between PCA0CPH5 and
PCA0H. Software may force a WDT reset by writing a 1 to the CCF5 flag (PCA0CN.5) while the WDT is
enabled.
28.4.2. Watchdog Timer Usage
To configure the WDT, perform the following tasks:
Disable the WDT by writing a 0 to the WDTE bit.
 Select the desired PCA clock source (with the CPS2–CPS0 bits).
 Load PCA0CPL5 with the desired WDT update offset value.
 Configure the PCA Idle mode (set CIDL if the WDT should be suspended while the CPU is in Idle
mode).
 Enable the WDT by setting the WDTE bit to 1.
 Reset the WDT timer by writing to PCA0CPH5.
The PCA clock source and Idle mode select cannot be changed while the WDT is enabled. The watchdog
timer is enabled by setting the WDTE or WDLCK bits in the PCA0MD register. When WDLCK is set, the
WDT cannot be disabled until the next system reset. If WDLCK is not set, the WDT is disabled by clearing
the WDTE bit.

The WDT is enabled following any reset. The PCA0 counter clock defaults to the system clock divided by
12, PCA0L defaults to 0x00, and PCA0CPL5 defaults to 0x00. Using Equation 28.5, this results in a WDT
timeout interval of 256 PCA clock cycles, or 3072 system clock cycles. Table 28.3 lists some example timeout intervals for typical system clocks.
Table 28.3. Watchdog Timer Timeout Intervals1
System Clock (Hz)
PCA0CPL5
Timeout Interval (ms)
24,500,000
255
32.1
24,500,000
128
16.2
24,500,000
32
4.1
3,062,5002
255
257
2
128
129.5
2
3,062,500
32
33.1
32,000
255
24576
32,000
128
12384
32,000
32
3168
3,062,500
Notes:
1. Assumes SYSCLK/12 as the PCA clock source, and a PCA0L value
of 0x00 at the update time.
2. Internal SYSCLK reset frequency = Internal Oscillator divided by 8.
Rev. 1.3
369
Si1000/1/2/3/4/5
28.5. Register Descriptions for PCA0
Following are detailed descriptions of the special function registers related to the operation of the PCA.
SFR Definition 28.1. PCA0CN: PCA Control
Bit
7
6
5
4
3
2
1
0
Name
CF
CR
CCF5
CCF4
CCF3
CCF2
CCF1
CCF0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xD8; Bit-Addressable
Bit
Name
Function
7
CF
PCA Counter/Timer Overflow Flag.
Set by hardware when the PCA Counter/Timer overflows from 0xFFFF to 0x0000.
When the Counter/Timer Overflow (CF) interrupt is enabled, setting this bit causes the
CPU to vector to the PCA interrupt service routine. This bit is not automatically cleared
by hardware and must be cleared by software.
6
CR
PCA Counter/Timer Run Control.
This bit enables/disables the PCA Counter/Timer.
0: PCA Counter/Timer disabled.
1: PCA Counter/Timer enabled.
5:0
CCF[5:0] PCA Module n Capture/Compare Flag.
These bits are set by hardware when a match or capture occurs in the associated PCA
Module n. When the CCFn interrupt is enabled, setting this bit causes the CPU to
vector to the PCA interrupt service routine. This bit is not automatically cleared by
hardware and must be cleared by software.
370
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 28.2. PCA0MD: PCA Mode
Bit
7
6
5
Name
CIDL
WDTE
WDLCK
Type
R/W
R/W
R/W
Reset
0
1
0
4
3
2
1
0
CPS2
CPS1
CPS0
ECF
R
R/W
R/W
R/W
R/W
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xD9
Bit
Name
7
CIDL
Function
PCA Counter/Timer Idle Control.
Specifies PCA behavior when CPU is in Idle Mode.
0: PCA continues to function normally while the system controller is in Idle Mode.
1: PCA operation is suspended while the system controller is in Idle Mode.
6
WDTE
Watchdog Timer Enable.
If this bit is set, PCA Module 2 is used as the watchdog timer.
0: Watchdog Timer disabled.
1: PCA Module 2 enabled as Watchdog Timer.
5
WDLCK
Watchdog Timer Lock.
This bit locks/unlocks the Watchdog Timer Enable. When WDLCK is set, the Watchdog
Timer may not be disabled until the next system reset.
0: Watchdog Timer Enable unlocked.
1: Watchdog Timer Enable locked.
4
3:1
Unused
Read = 0b, Write = don't care.
CPS[2:0] PCA Counter/Timer Pulse Select.
These bits select the timebase source for the PCA counter
000: System clock divided by 12
001: System clock divided by 4
010: Timer 0 overflow
011: High-to-low transitions on ECI (max rate = system clock divided by 4)
100: System clock
101: External clock divided by 8 (synchronized with the system clock)
110: Reserved
111: Reserved
0
ECF
PCA Counter/Timer Overflow Interrupt Enable.
This bit sets the masking of the PCA Counter/Timer Overflow (CF) interrupt.
0: Disable the CF interrupt.
1: Enable a PCA Counter/Timer Overflow interrupt request when CF (PCA0CN.7) is
set.
Note: When the WDTE bit is set to 1, the other bits in the PCA0MD register cannot be modified. To change the
contents of the PCA0MD register, the Watchdog Timer must first be disabled.
Rev. 1.3
371
Si1000/1/2/3/4/5
SFR Definition 28.3. PCA0PWM: PCA PWM Configuration
Bit
7
6
5
4
Name
ARSEL
ECOV
COVF
Type
R/W
R/W
R/W
R
R
R
Reset
0
0
0
0
0
0
ARSEL
2
1
0
CLSEL[1:0]
SFR Page = 0x0; SFR Address = 0xDF
Bit
Name
7
3
R/W
0
0
Function
Auto-Reload Register Select.
This bit selects whether to read and write the normal PCA capture/compare registers
(PCA0CPn), or the Auto-Reload registers at the same SFR addresses. This function
is used to define the reload value for 9, 10, and 11-bit PWM modes. In all other
modes, the Auto-Reload registers have no function.
0: Read/Write Capture/Compare Registers at PCA0CPHn and PCA0CPLn.
1: Read/Write Auto-Reload Registers at PCA0CPHn and PCA0CPLn.
6
ECOV
Cycle Overflow Interrupt Enable.
This bit sets the masking of the Cycle Overflow Flag (COVF) interrupt.
0: COVF will not generate PCA interrupts.
1: A PCA interrupt will be generated when COVF is set.
5
COVF
Cycle Overflow Flag.
This bit indicates an overflow of the 8th, 9th, 10th, or 11th bit of the main PCA counter
(PCA0). The specific bit used for this flag depends on the setting of the Cycle Length
Select bits. The bit can be set by hardware or software, but must be cleared by software.
0: No overflow has occurred since the last time this bit was cleared.
1: An overflow has occurred since the last time this bit was cleared.
4:2
Unused
Read = 000b; Write = don’t care.
1:0 CLSEL[1:0] Cycle Length Select.
When 16-bit PWM mode is not selected, these bits select the length of the PWM
cycle, between 8, 9, 10, or 11 bits. This affects all channels configured for PWM which
are not using 16-bit PWM mode. These bits are ignored for individual channels configured to16-bit PWM mode.
00: 8 bits.
01: 9 bits.
10: 10 bits.
11: 11 bits.
372
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 28.4. PCA0CPMn: PCA Capture/Compare Mode
Bit
7
6
5
4
3
2
1
0
Name
PWM16n
ECOMn
CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address, Page: PCA0CPM0 = 0xDA, 0x0; PCA0CPM1 = 0xDB, 0x0; PCA0CPM2 = 0xDC, 0x0
PCA0CPM3 = 0xDD, 0x0; PCA0CPM4 = 0xDE, 0x0; PCA0CPM5 = 0xCE, 0x0
Bit
Name
Function
7
PWM16n 16-bit Pulse Width Modulation Enable.
This bit enables 16-bit mode when Pulse Width Modulation mode is enabled.
0: 8 to 11-bit PWM selected.
1: 16-bit PWM selected.
6
ECOMn
Comparator Function Enable.
This bit enables the comparator function for PCA module n when set to 1.
5
CAPPn
Capture Positive Function Enable.
This bit enables the positive edge capture for PCA module n when set to 1.
4
CAPNn
Capture Negative Function Enable.
This bit enables the negative edge capture for PCA module n when set to 1.
3
MATn
Match Function Enable.
This bit enables the match function for PCA module n when set to 1. When enabled,
matches of the PCA counter with a module's capture/compare register cause the CCFn
bit in PCA0MD register to be set to logic 1.
2
TOGn
Toggle Function Enable.
This bit enables the toggle function for PCA module n when set to 1. When enabled,
matches of the PCA counter with a module's capture/compare register cause the logic
level on the CEXn pin to toggle. If the PWMn bit is also set to logic 1, the module operates in Frequency Output Mode.
1
PWMn
Pulse Width Modulation Mode Enable.
This bit enables the PWM function for PCA module n when set to 1. When enabled, a
pulse width modulated signal is output on the CEXn pin. 8 to 11-bit PWM is used if
PWM16n is cleared; 16-bit mode is used if PWM16n is set to logic 1. If the TOGn bit is
also set, the module operates in Frequency Output Mode.
0
ECCFn
Capture/Compare Flag Interrupt Enable.
This bit sets the masking of the Capture/Compare Flag (CCFn) interrupt.
0: Disable CCFn interrupts.
1: Enable a Capture/Compare Flag interrupt request when CCFn is set.
Note: When the WDTE bit is set to 1, the PCA0CPM5 register cannot be modified, and module 5 acts as the
watchdog timer. To change the contents of the PCA0CPM5 register or the function of module 5, the Watchdog
Timer must be disabled.
Rev. 1.3
373
Si1000/1/2/3/4/5
SFR Definition 28.5. PCA0L: PCA Counter/Timer Low Byte
Bit
7
6
5
4
3
2
1
0
PCA0[7:0]
Name
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xF9
Bit
Name
7:0
Function
PCA0[7:0] PCA Counter/Timer Low Byte.
The PCA0L register holds the low byte (LSB) of the 16-bit PCA Counter/Timer.
Note: When the WDTE bit is set to 1, the PCA0L register cannot be modified by software. To change the contents of
the PCA0L register, the Watchdog Timer must first be disabled.
SFR Definition 28.6. PCA0H: PCA Counter/Timer High Byte
Bit
7
6
5
4
3
2
1
0
PCA0[15:8]
Name
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Page = 0x0; SFR Address = 0xFA
Bit
Name
7:0
Function
PCA0[15:8] PCA Counter/Timer High Byte.
The PCA0H register holds the high byte (MSB) of the 16-bit PCA Counter/Timer.
Reads of this register will read the contents of a “snapshot” register, whose contents
are updated only when the contents of PCA0L are read (see Section 28.1).
Note: When the WDTE bit is set to 1, the PCA0H register cannot be modified by software. To change the contents of
the PCA0H register, the Watchdog Timer must first be disabled.
374
Rev. 1.3
Si1000/1/2/3/4/5
SFR Definition 28.7. PCA0CPLn: PCA Capture Module Low Byte
Bit
7
6
5
4
3
2
1
0
PCA0CPn[7:0]
Name
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Addresses: PCA0CPL0 = 0xFB, PCA0CPL1 = 0xE9, PCA0CPL2 = 0xEB,
PCA0CPL3 = 0xED, PCA0CPL4 = 0xFD, PCA0CPL5 = 0xD2
SFR Pages:
Bit
7:0
PCA0CPL0 = 0x0, PCA0CPL1 = 0x0, PCA0CPL2 = 0x0,
PCA0CPL3 = 0x0, PCA0CPL4 = 0x0, PCA0CPL5 = 0x0
Name
Function
PCA0CPn[7:0] PCA Capture Module Low Byte.
The PCA0CPLn register holds the low byte (LSB) of the 16-bit capture module n.
This register address also allows access to the low byte of the corresponding
PCA channel’s auto-reload value for 9, 10, or 11-bit PWM mode. The ARSEL bit
in register PCA0PWM controls which register is accessed.
Note: A write to this register will clear the module’s ECOMn bit to a 0.
SFR Definition 28.8. PCA0CPHn: PCA Capture Module High Byte
Bit
7
6
5
4
3
2
1
0
PCA0CPn[15:8]
Name
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Addresses: PCA0CPH0 = 0xFC, PCA0CPH1 = 0xEA, PCA0CPH2 = 0xEC,
PCA0CPH3 = 0xEE, PCA0CPH4 = 0xFE, PCA0CPH5 = 0xD3
SFR Pages:
Bit
PCA0CPH0 = 0x0, PCA0CPH1 = 0x0, PCA0CPH2 = 0x0,
PCA0CPH3 = 0x0, PCA0CPH4 = 0x0, PCA0CPH5 = 0x0
Name
Function
7:0 PCA0CPn[15:8] PCA Capture Module High Byte.
The PCA0CPHn register holds the high byte (MSB) of the 16-bit capture module n.
This register address also allows access to the high byte of the corresponding
PCA channel’s auto-reload value for 9, 10, or 11-bit PWM mode. The ARSEL bit in
register PCA0PWM controls which register is accessed.
Note: A write to this register will set the module’s ECOMn bit to a 1.
Rev. 1.3
375
Si1000/1/2/3/4/5
29. Device Specific Behavior
This chapter contains behavioral differences between the silicon revisions of Si100x devices. These differences do not affect the functionality or performance of most systems and are described below.
29.1. Device Identification
The Part Number Identifier on the top side of the device package can be used for decoding device information. The first character of the trace code identifies the silicon revision. On Si100x devices, the trace code
will be the fifth letter on the second line. Figure 29.1 show how to find the part number on the top side of
the device package.
This fifth character identifies
the device revision.
Figure 29.1. Si100x Revision Information
376
Rev. 1.3
Si1000/1/2/3/4/5
30. C2 Interface
Si1000/1/2/3/4/5 devices include an on-chip Silicon Labs 2-Wire (C2) debug interface to allow flash programming and in-system debugging with the production part installed in the end application. The C2 interface uses a clock signal (C2CK) and a bi-directional C2 data signal (C2D) to transfer information between
the device and a host system. See the C2 Interface Specification for details on the C2 protocol.
30.1. C2 Interface Registers
The following describes the C2 registers necessary to perform flash programming through the C2 interface. All C2 registers are accessed through the C2 interface as described in the C2 Interface Specification.
C2 Register Definition 30.1. C2ADD: C2 Address
Bit
7
6
5
4
3
Name
C2ADD[7:0]
Type
R/W
Reset
Bit
0
0
0
0
Name
0
2
1
0
0
0
0
Function
7:0 C2ADD[7:0] C2 Address.
The C2ADD register is accessed via the C2 interface to select the target Data register
for C2 Data Read and Data Write commands.
Address
Description
0x00
Selects the Device ID register for Data Read instructions
0x01
Selects the Revision ID register for Data Read instructions
0x02
Selects the C2 Flash Programming Control register for Data
Read/Write instructions
0xB4
Selects the C2 Flash Programming Data register for Data
Read/Write instructions
Rev. 1.3
377
Si1000/1/2/3/4/5
C2 Register Definition 30.2. DEVICEID: C2 Device ID
Bit
7
6
5
4
3
Name
DEVICEID[7:0]
Type
R/W
Reset
0
0
0
1
0
C2 Address: 0x00
Bit
Name
7:0
2
1
0
1
0
0
Function
DEVICEID[7:0] Device ID.
This read-only register returns the 8-bit device ID: 0x16 (Si1000/1/2/3/4/5).
C2 Register Definition 30.3. REVID: C2 Revision ID
Bit
7
6
5
4
3
Name
REVID[7:0]
Type
R/W
Reset
Varies
Varies
Varies
Varies
C2 Address: 0x01
Bit
Name
7:0
Varies
2
1
0
Varies
Varies
Varies
Function
REVID[7:0] Revision ID.
This read-only register returns the 8-bit revision ID. For example: 0x00 = Revision A.
378
Rev. 1.3
Si1000/1/2/3/4/5
C2 Register Definition 30.4. FPCTL: C2 Flash Programming Control
Bit
7
6
5
4
3
Name
FPCTL[7:0]
Type
R/W
Reset
0
0
0
0
0
C2 Address: 0x02
Bit
Name
7:0
2
1
0
0
0
0
Function
FPCTL[7:0] Flash Programming Control Register.
This register is used to enable flash programming via the C2 interface. To enable C2
flash programming, the following codes must be written in order: 0x02, 0x01. Note
that once C2 flash programming is enabled, a system reset must be issued to resume
normal operation.
C2 Register Definition 30.5. FPDAT: C2 Flash Programming Data
Bit
7
6
5
4
3
Name
FPDAT[7:0]
Type
R/W
Reset
0
0
0
0
C2 Address: 0xB4
Bit
Name
7:0
0
2
1
0
0
0
0
Function
FPDAT[7:0] C2 Flash Programming Data Register.
This register is used to pass flash commands, addresses, and data during C2 flash
accesses. Valid commands are listed below.
Code
Command
0x06
Flash Block Read
0x07
Flash Block Write
0x08
Flash Page Erase
0x03
Device Erase
Rev. 1.3
379
Si1000/1/2/3/4/5
30.2. C2 Pin Sharing
The C2 protocol allows the C2 pins to be shared with user functions so that in-system debugging and flash
programming may be performed. This is possible because C2 communication is typically performed when
the device is in the halt state, where all on-chip peripherals and user software are stalled. In this halted
state, the C2 interface can safely “borrow” the C2CK (RST) and C2D pins. In most applications, external
resistors are required to isolate C2 interface traffic from the user application. A typical isolation configuration is shown in Figure 30.1.
C8051Fxxx
RST (a)
C2CK
Input (b)
C2D
Output (c)
C2 Interface Master
Figure 30.1. Typical C2 Pin Sharing
The configuration in Figure 30.1 assumes the following:
1. The user input (b) cannot change state while the target device is halted.
2. The RST pin on the target device is used as an input only.
Additional resistors may be necessary depending on the specific application.
380
Rev. 1.3
Si1000/1/2/3/4/5
DOCUMENT CHANGE LIST

Revision 0.2 to Revision 1.0











Updated specification tables.
Added Temperature Sensor Settling Time
Specification.
Updated power management section to indicate that
the low power or precision oscillator must be
selected when entering sleep or suspend mode.
Also added a recommendation of executing two
NOP instructions following the wake up from sleep
mode.
Updated ADC0 Burst Mode description.
Updated DC0 inductor peak current equation.
Added a note to the OSCICL register description.
Updated Section 20.3 to indicate that when using
Auto Reset, the Alarm match value should always be
set to 2 counts less than the desired match value.
Updated Port I/O chapter with additional clarification
on 5 V and 3.3 V tolerance.
Updated EZRadioPRO chapter.
Updated QFN-42 landing diagram and stencil
recommendations.









Revision 1.0 to Revision 1.1










Added revision E information to section “2. Ordering
Information”
Added LGA-42 package information to section “3.
Pinout and Package Definitions” .
Clarified conditions that apply to “VBAT Ramp Time
for Power On” for one-cell mode vs. two-cell mode in
Table 4.4.
Added Si100x-E-GM POR Reset Time value to
Table 4.20.
Updated “5.2.3. Burst Mode” and Figure 5.3 to show
difference in behavior between internal convert start
signals and external CNVSTR signal.
Added note about the need to ground the ADC mux
before switching to the temperature sensor in “5.6.
Temperature Sensor” and in SFR
Definition 5.12. ADC0MX: ADC0 Input Channel
Select
Updated Table 8.1 on page 112 to correct number of
clock cycles for “CJNE A, direct, rel”.
Updated CPT0WK bit description in Register 14.1,
“PMU0CF: Power Management Unit
Configuration1,2,” on page 157.
Added section “15.2. 32-bit CRC Algorithm” to
illustrate the 32-bit CRC algorithm.
Updated links from section “19. Clocking Sources”
381
Rev. 1.3

to the proper Electrical Characteristics table.
Changed the reset value of Register 00 in Table 23.9
Updated Figure 23.6, “FSK vs. GFSK Spectrums,”
on page 255 and Figure 23.7, “Direct Synchronous
Mode Example,” on page 258
Updated the Important Note in section “23.2.
Interrupts ”
Removed support for the Low Battery Detector in
section “23.8.5. Low Battery Detector”
Updated item 2 in section “23.13. Required Changes
to Default Register Values”
Corrected clock sources associated with T3XCLK
settings in section “27.1.3. Mode 2: 8-bit
Counter/Timer with Auto-Reload” , Figure 27.7,
Figure 27.8, and Figure 27.9 to match the
description in SFR Definition 27.13.
Updated text in the first paragraph of the section “28.
Programmable Counter Array” .
Changed all instances of “ANT” to “ANT_A”.
Updated the description of the XOUT and XIN pins.
Updated QFN-42 stencil design and card assembly
recommendations.
Replaced incorrect PCA channel references from
PCA0CPH2 to PCA0CPH5 in “28.4. Watchdog Timer
Mode” and Figure 28.11, “PCA Module 5 with
Watchdog Timer Enabled,” on page 368.
Added section “29. Device Specific Behavior”
Revision 1.1 to Revision 1.2








Update Figure 3.3 to show asymmetry of center pad.
Updated Figure 3.4 to show asymmetry of center
pad.
Updated Figure 3.5 dimensions and removed notes.
Updated Table 3.4 dimensions.
Updated Table 3.3 dimensions and removed Note 4.
Added values for Si1004 and Si1005 to section 13.4.
Updated Table 23.6 description of VDD Glitch Reset
Pulse time.
Updated Table 23.9 to show Device Version as 06h
for Si100x-C-GM and 07h for Si100x-E-GM.
Revision 1.2 to Revision 1.3
Removed all references to Si100x-C-GM parts.
 Removed all references to Si100x-E-GM parts.
 Added ordering part numbers for Si100x-E-GM2
parts.
 Added package information for Si100x-E-GM2 parts.

Si1000/1/2/3/4/5
CONTACT INFORMATION
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Please visit the Silicon Labs Technical Support web page:
https://www.silabs.com/support/pages/contacttechnicalsupport.aspx
and register to submit a technical support request.
Patent Notice
Silicon Labs invests in research and development to help our customers differentiate in the market with innovative low-power, small
size, analog-intensive mixed-signal solutions. Silicon Labs' extensive patent portfolio is a testament to our unique approach and worldclass engineering team.
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for
the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further
notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other
application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may
occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer
shall indemnify and hold Silicon Laboratories harmless against all claims and damages.
Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
382
Rev. 1.3