Data Sheet Rev. 1.00 / July 2014 ZSSC1750/51 Data Acquisition System Basis Chip Battery Management ICs Adaptive and Efficient ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Brief Description Benefits The ZSSC1750 and ZSSC1751 are System Basis Chips (SBCs) with a dual-channel ADC for battery sensing/management in automotive, industrial, and medical systems. The ZSSC1750 and ZSSC1751 feature an SPI interface; in addition, the ZSSC1750 has an integrated LIN 2.1 transceiver. One of the two input channels measures the battery current IBAT via the voltage drop at the external shunt resistor. The second channel measures the battery voltage VBAT and the temperature. By simultaneously measuring VBAT and IBAT, it is possible to determine dynamically the internal resistance of the battery, Rdi, which is correlated with the state-of-health (SOH) of the battery. By integrating IBAT, it is possible to determine the stateof-charge (SOC) and the state-of-function (SOF) of the battery. During Sleep Mode, the system makes periodic measurements to monitor the discharge of the battery. Measurement cycles are controlled by user software and include various wake-up conditions. The ZSSC1750/51 is optimized for ultra-low power consumption drawing only 60µA or less in this mode. Integrated, precision measurement solution for accurate prediction of battery state of health (SOH), state of charge (SOC), or state of function (SOF) Robust power-on-reset (POR) concept for harsh automotive environments On-chip precision oscillator accuracy: ±1% On-chip low-power oscillator Only a few external components needed Easy communication via SPI interface Power supply, interrupt, and reset signals for external microcontroller Watchdog timer with dedicated oscillator Industry’s smallest footprint allows minimal module size and cost AEC-Q100 qualified solution Available Support Evaluation Kit Application Notes Physical Characteristics Features Two high-precision 24-bit sigma-delta ADCs (18-bit with no missing codes); sample rate: 1Hz to 16kHz On-chip voltage reference (5ppm/K typical) Current channel IBAT offset error: ≤ 10mA IBAT resolution: ≤ 1mA Programmable gain: 4 to 512 Max. differential input stage input range: ±300mV Voltage channel Input range: 4 to 28.8V Voltage accuracy: ±60ppm FSR* = 1.73mV Temperature channel External temperature sensor (NTC) Factory-calibrated internal temp. sensor: ±2°C LIN 2.1/SAE J2602-1 transceiver (ZSSC1750 only) Typical current consumption Normal Mode: 12mA Sleep Mode: ≤ 60µA Operation temperature up to -40°C to +125°C Supply voltage: 4.2 to 18V Small footprint package: PQFN36 6x6 mm * FSR = full-scale range. Basic ZSSC1750/51 Application Circuit To Harness + - Car Chassis Ground VDDP VBAT VDDE INP INN VDDA Rshunt LIN 3.3V, <30mA LIN-I/F (ZSSC1750 ) RX TX IRQN MCU_RSTN MCU_CLK VDD IRQ RST CLK (opt.) NTH + - Battery NTC µC ZSSC1750/51 NTL VSSA SPI VSSE Interface to Host (e.g. CAN) I/F SPI VSS For more information, contact ZMDI via [email protected]. © 2014 Zentrum Mikroelektronik Dresden AG — Rev. 1.00 — July 10, 2014 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Common Ground VBAT ZSSC1750/51 Block Diagram Analog Block ZSSC1750/51 Analog Front End SBC Digital Block LP_REG VDDP_REG BG_REF WD_TIMER IRQ_CTRL VDDA_REG VDDC_REG SBC_PMU GP_TIMER OSC DIGITAL FILTER CONFIG REGISTER RESULT REGISTER VDDP VDDE VDDC VDDA SLEEPN WDT_DIS INP Applications SHUNT Intelligent battery monitoring in SD_ADC INN automotive applications; start/stop systems, e-bikes, scooters, and e-carts IRQN + – BATTERY and photovoltaic applications; LIN Rinn tck NTL RXD TMS csn sclk mosi miso TRSTN tms VSSR open sleepn VDDL TEST SLEEPN n.c . ZSSC1751 INN Cinn 10nF Rref 75kΩ Rntc 10kΩ trstn TESTL INP Cin 100nF BAT- Cdda 470nF VDDC VPP VSSR sto TCK VDDP sleepn VDDL TEST STO n.c. VSSA mcu_clk STO sto TCK tck TMS tms NTH NC VSSN wdt_dis MCU_CLK VDDA NTL Cntc 470pF WDT_DIS VSSA NC MISO 220Ω VSS TESTH MOSI Rshunt 100µΩ Cinp 10nF NC VSSE SCLK mcu_clk VDDA NTH Cntc 470pF VBAT Cddl 10nF CSN MCU_CLK VSSA MISO Rref 75kΩ 1 100nF IRQN wdt_dis Rinp 10µF MCU_RSTN WDT_DIS Chassis GND 220Ω Cinn 10nF Rntc 10kΩ ZSSC1750 MOSI 220Ω Cdda 470nF n.c . INN Rdde Cdde1 Cdde2 Cddp 2.2µF VDDE TESTL SCLK Rinn BAT- Ddde VSSA INP Cin 100nF LIN BAS21 2.2Ω CSN 220Ω Cbat 100nF VSSLIN n.c. IRQN Rshunt 100µΩ Cinp 10nF Cddc 2.2µF Rbat BAT+ 100Ω TESTH MCU_RSTN Rinp Available in ZSSC1750 only LIN Clin 220pF VSSE TXD Chassis GND 100nF Cddl 10nF SLEEPN VDDE 10µF VDDC VBAT 1 VPP Cddp 2.2µF VDDP Rdde Cdde1 Cdde2 RXD TXD LIN_PHYS (1) ZSSC1751 Typical Application Circuit Cddc 2.2µF Rbat Ddde CSN SCLK MISO MOSI SPI MUX LIN ZSSC1750 Typical Application Circuit BAS21 2.2Ω CALIBRATION DATA PATH NTC 1) Cbat 100nF DIGITAL FILTER SD_ADC NTH NTL High precision data acquisition 100Ω MCU_RSTN RREF Battery monitoring in Industrial, medical BAT+ MCU_CLK PGA VBAT csn sclk mosi miso TRSTN trstn VSSN VDDP open rxd txd mcu_rstn irqn mcu_rstn irqn Ordering Information Product Sales Code ZSSC1750EA1B ZSSC1750EA3R ZSSC1751EA3R ZSSC1750KIT V1.1 Description Package ZSSC1750 Battery Sensing SBC—Temperature Range: -40°C to 125°C Tested die on unsawn wafer ZSSC1750 Battery Sensing SBC—Temperature Range: -40°C to 125°C PQFN36 6x6 mm, reel ZSSC1751 Battery Sensing SBC—Temperature Range: -40°C to 125°C PQFN36 6x6 mm, reel ZSSC1750/51 Evaluation Kit: modular evaluation and development board for ZSSC1750/51, 3 IC samples, and USB cable (software and documentation can be downloaded from the product page at www.zmdi.com/zssc175x) Sales and Further Information www.zmdi.com [email protected] Zentrum Mikroelektronik Dresden AG Global Headquarters Grenzstrasse 28 01109 Dresden, Germany ZMD America, Inc. 1525 McCarthy Blvd., #212 Milpitas, CA 95035-7453 USA Central Office: Phone +49.351.8822.306 Fax +49.351.8822.337 USA Phone: 1.855.275.9634 Phone +1.408.883.6310 Fax +1.408.883.6358 European Technical Support Phone +49.351.8822.7.772 Fax +49.351.8822.87.772 DISCLAIMER: This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Zentrum Mikroelektronik Dresden AG (ZMD AG) assumes no obligation regarding future manufacture unless otherwise agreed to in writing. The information furnished hereby is believed to be true and accurate. However, under no circumstances shall ZMD AG be liable to any customer, licensee, or any other third party for any special, indirect, incidental, or consequential damages of any kind or nature whatsoever arising out of or in any way related to the furnishing, performance, or use of this technical data. ZMD AG hereby expressly disclaims any liability of ZMD AG to any customer, licensee or any other third party, and any such customer, licensee and any other third party hereby waives any liability of ZMD AG for any damages in connection with or arising out of the furnishing, performance or use of this technical data, whether based on contract, warranty, tort (including negligence), strict liability, or otherwise. European Sales (Stuttgart) Phone +49.711.674517.55 Fax +49.711.674517.87955 Zentrum Mikroelektronik Dresden AG, Japan Office 2nd Floor, Shinbashi Tokyu Bldg. 4-21-3, Shinbashi, Minato-ku Tokyo, 105-0004 Japan ZMD FAR EAST, Ltd. 3F, No. 51, Sec. 2, Keelung Road 11052 Taipei Taiwan Phone +81.3.6895.7410 Fax +81.3.6895.7301 Phone +886.2.2377.8189 Fax +886.2.2377.8199 Zentrum Mikroelektronik Dresden AG, Korea Office U-space 1 Building 11th Floor, Unit JA-1102 670 Sampyeong-dong Bundang-gu, Seongnam-si Gyeonggi-do, 463-400 Korea Phone +82.31.950.7679 Fax +82.504.841.3026 © 2014 Zentrum Mikroelektronik Dresden AG — Rev. 1.00 — July 10, 2014 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Contents 1 IC Characteristics ............................................................................................................................................. 9 1.1 Absolute Maximum Ratings ....................................................................................................................... 9 1.2 Recommended Operating Conditions ..................................................................................................... 10 1.3 Electrical Parameters .............................................................................................................................. 11 1.4 Timing Parameters .................................................................................................................................. 19 2 Circuit Description .......................................................................................................................................... 22 2.1 Overview .................................................................................................................................................. 22 2.2 SBC-to-MCU Interface Pins ..................................................................................................................... 23 2.2.1 Digital I/Os ........................................................................................................................................ 24 2.2.2 External Microcontroller (MCU) Supply Pins .................................................................................... 24 2.2.3 SLEEPN Power State Indicator Pin .................................................................................................. 24 2.3 System Power States .............................................................................................................................. 25 2.3.1 Full Power State (FP) ....................................................................................................................... 25 2.3.2 Low Power State (LP) ...................................................................................................................... 25 2.3.3 Ultra Low Power State (ULP) ........................................................................................................... 26 2.3.4 OFF Power State .............................................................................................................................. 26 3 ZSSC1750/51 Functional Block Descriptions ................................................................................................ 27 3.1 Serial Peripheral Interface (SPI Slave) .................................................................................................... 27 3.1.1 SPI Protocol ...................................................................................................................................... 27 3.2 SBC Register Map (RESULT REGISTER Block and CONFIG REGISTER Block) ................................ 29 3.3 ZSSC1750/51 Clock and Reset Logic ..................................................................................................... 34 3.3.1 Clock Sources .................................................................................................................................. 34 3.3.2 Trimming the Low-Power Oscillator ................................................................................................. 35 3.3.3 Clock Trimming and Configuration Registers ................................................................................... 36 3.3.4 Resets .............................................................................................................................................. 38 3.4 SBC Watchdog Timer (WD_TIMER Block) ............................................................................................. 40 3.4.1 Watchdog Registers ......................................................................................................................... 42 3.5 SBC Sleep Timer (GP_TIMER Block) ..................................................................................................... 44 3.5.1 Sleep Timer Registers ...................................................................................................................... 45 3.6 SBC Interrupt Controller (IRQ_CTRL Block) ........................................................................................... 46 3.7 SBC Power Management Unit (SBC_PMU Block) .................................................................................. 50 3.7.1 FP State ............................................................................................................................................ 51 3.7.2 LP and ULP States ........................................................................................................................... 52 3.7.3 OFF State ......................................................................................................................................... 61 3.7.4 Registers for Power Configuration and the Discreet Current Measurement Count ......................... 62 3.8 ZSSC1750/51 ADC Unit .......................................................................................................................... 64 3.8.1 ADC Clocks ...................................................................................................................................... 65 3.8.2 ADC Data Path ................................................................................................................................. 70 3.8.3 ADC Operating Modes and Result Registers ................................................................................... 75 3.8.4 ADC Control and Conversion Timing ............................................................................................... 87 3.8.5 Diagnostic Features.......................................................................................................................... 97 Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 4 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 4 5 6 7 8 9 3.8.6 Digital Features ................................................................................................................................ 98 3.9 SBC LIN Support Logic (for ZSSC1750 only) ....................................................................................... 101 3.9.1 LIN Wakeup Detection ................................................................................................................... 101 3.9.2 TXD Timeout Detection .................................................................................................................. 101 3.9.3 LIN Short Detection ........................................................................................................................ 102 3.9.4 LIN Testing ..................................................................................................................................... 103 3.10 ZSSC1750/51 OTP (CONFIG REGISTER) ........................................................................................... 105 3.11 Miscellaneous Registers ........................................................................................................................ 106 3.12 Voltage Regulators ................................................................................................................................ 109 3.12.1 VDDE .............................................................................................................................................. 109 3.12.2 VBAT .............................................................................................................................................. 109 3.12.3 VDDA .............................................................................................................................................. 109 3.12.4 VDDL .............................................................................................................................................. 110 3.12.5 VDDP .............................................................................................................................................. 110 3.12.6 VDDC ............................................................................................................................................. 110 ESD / EMC ................................................................................................................................................... 111 4.1 Electrostatic Discharge .......................................................................................................................... 111 4.2 Power System Ripple Factor ................................................................................................................. 111 4.3 Application Circuit Examples for EMC Conformance ............................................................................ 112 Pin Configuration and Package .................................................................................................................... 113 Ordering Information .................................................................................................................................... 116 Related Documents ...................................................................................................................................... 116 Glossary ....................................................................................................................................................... 116 Document Revision History .......................................................................................................................... 117 List of Figures Figure 1.1 Figure 1.2 Figure 1.3 Figure 2.1 Figure 2.2 Figure 2.3 Figure 3.1 Figure 3.2 Figure 3.3 Figure 3.4 Figure 3.5 Figure 3.6 Figure 3.7 Data Sheet July 10, 2014 Measurement Method for Determining VDDP Pin Current Capability .............................................. 18 SPI Protocol Timing .......................................................................................................................... 20 ZSSC1750/51 Power-Up and Power-Down Sequence .................................................................... 21 Functional Block Diagram ................................................................................................................. 22 ZSSC1750/51 Digital IO Interface .................................................................................................... 23 ZSSC1750/51 Power States ............................................................................................................. 25 Read and Write Burst Access to the SBC ........................................................................................ 28 Structure of the Watchdog Timer ...................................................................................................... 40 Structure of the Sleep Timer ............................................................................................................. 44 Generation of Interrupt and Wake-up ............................................................................................... 47 LP/ULP State without any Measurements ........................................................................................ 53 LP/ULP State Performing Only Current Measurements ................................................................... 55 LP/ULP State Performing Current, Voltage, and Temperature Measurements with discCvtCnt == 2 ..................................................................................................................... 57 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 5 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.8 Figure 3.9 Figure 3.10 Figure 3.11 Figure 3.12 Figure 3.13 Figure 3.14 Figure 3.15 Figure 3.16 Figure 3.17 Figure 3.18 Figure 3.19 Figure 3.20 Figure 3.21 Figure 3.22 Figure 3.23 Figure 3.24 Figure 3.25 Figure 3.26 Figure 3.27 Figure 3.28 Figure 3.29 Figure 3.30 Figure 3.31 Figure 3.32 Figure 3.33 Figure 3.34 Figure 3.35 Figure 3.36 Figure 3.37 Figure 3.38 Figure 4.1 Figure 4.2 Figure 5.1 Figure 5.2 Data Sheet July 10, 2014 LP/ULP State Performing Current, Voltage, and Temperature Measurements with discCvtCnt == 5 ..................................................................................................................... 57 LP/ULP State Performing Current, Voltage, and Temperature Measurements with discCvtCnt == 1 ..................................................................................................................... 58 LP/ULP State Performing Continuous Current-Only Measurements ............................................... 59 Performing Continuous Current and Voltage Measurements during LP/ULP State......................... 61 Functional Block Diagram of the Analog Measurement Subsystem ................................................ 65 FP ADC Clocking Scheme for sdmPos = sdmPos2 = 2; sdmClkDivFp = 1; sdmChopClkDiv = 0 ........................................................................................................................ 67 FP ADC Clocking for sdmPos = 1 and sdmPos2 = 4; sdmClkDivFp = 1; sdmChopClkDiv = 0... 67 FP ADC Clocking for sdmPos = 3 and sdmPos2 = 0; sdmClkDivFp = 1; sdmChopClkDiv = 0... 68 FP ADC Clocking for sdmPos = 0 and sdmPos2 = 3; sdmClkDivFp = 1; sdmChopClkDiv = 0... 68 LP/ULP ADC Clocking Scheme; sdmClkDivLp = 5; sdmChopClkDiv = 0 ................................... 69 Functional Block Diagram of the Digital ADC Data Path .................................................................. 70 Data Post Correction ........................................................................................................................ 71 Data Representation through Data Post Correction including Over-Range and Overflow Levels ... 72 Common Enable for the “set overrange” and “set overflow” Interrupt Strobes for Current .............. 73 Individual SRCS ................................................................................................................................ 88 Individual MRCS (Example for Result Counter of 3) ........................................................................ 88 Continuous SRCS ............................................................................................................................. 89 Continuous MRCS (Example for Result Counter of 3) ..................................................................... 89 Stopping Continuous SRCS ............................................................................................................. 90 Stopping Continuous MRCS (Example for Result Counter of 3) ...................................................... 90 Interrupting a Continuous SRCS ...................................................................................................... 91 Interrupting a Continuous MRCS (Example for Result Counter of 3) ............................................... 91 Signal Behavior of adcMode ............................................................................................................ 92 Timing for Current, Voltage, and Internal Temperature Measurements without Chopping for Different Configurations of the Average Filter .................................................................................. 94 Timing for External Temperature Measurements without Chopping when No Average Filter is Enabled ............................................................................................................ 95 Timing for Current, Voltage, and Internal Temperature Measurements using Chopping................. 96 Timing for External Temperature Measurements using Chopping ................................................... 97 Usage of Register adcCaccTh for the Digital ADC BIST ................................................................ 99 Bit Stream of ADC Interface Test at STO Pad ............................................................................... 100 Protection Logic of the LIN TXD Line ............................................................................................. 101 Waveform Showing the Gating Principle for Non-zero Values of linShortDelay...................... 102 Optional External Components for ZSSC1750 ............................................................................... 112 Optional External Components for ZSSC1751 ............................................................................... 112 ZSSC1750/51 PQFN36 6x6mm Package Pin-out (Top View) ....................................................... 113 Package Drawing of the ZSSC1750/51 .......................................................................................... 115 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 6 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) List of Tables Table 1.1 Table 1.2 Table 1.3 Table 1.4 Table 3.1 Table 3.2 Table 3.3 Table 3.4 Table 3.5 Table 3.6 Table 3.7 Table 3.8 Table 3.9 Table 3.10 Table 3.11 Table 3.12 Table 3.13 Table 3.14 Table 3.15 Table 3.16 Table 3.17 Table 3.18 Table 3.19 Table 3.20 Table 3.21 Table 3.22 Table 3.23 Table 3.24 Table 3.25 Table 3.26 Table 3.27 Table 3.28 Table 3.29 Table 3.30 Table 3.31 Table 3.32 Table 3.33 Table 3.34 Table 3.35 Data Sheet July 10, 2014 Absolute Maximum Ratings (referenced to VSSE) ............................................................................. 9 Operating Conditions ........................................................................................................................ 10 Electrical Specifications .................................................................................................................... 11 Timing Parameters ........................................................................................................................... 19 SBC Register Map ............................................................................................................................ 29 Register irefOsc ............................................................................................................................ 36 Register irefLpOsc ........................................................................................................................ 36 Register lpOscTrim ........................................................................................................................... 37 Register lpOscTrimCnt ................................................................................................................. 37 Register swRst ................................................................................................................................. 39 Register cmdExe............................................................................................................................... 39 Register funcDis ............................................................................................................................ 40 Resolution and Maximum Timeout for Prescaler Configurations ..................................................... 41 Register wdogPresetVal ............................................................................................................... 42 Register wdogCnt ............................................................................................................................ 42 Register wdogCfg ............................................................................................................................ 43 Register sleepTAdcCmp ................................................................................................................. 45 Register sleepTCmp ........................................................................................................................ 46 Register sleepTCurCnt ................................................................................................................. 46 Register irqStat ............................................................................................................................ 49 Register irqEna............................................................................................................................... 49 Register pwrCfgFp .......................................................................................................................... 62 Register pwrCfgLp .......................................................................................................................... 63 Register gotoPd............................................................................................................................... 64 Register discCvtCnt ...................................................................................................................... 64 Value for sdmPos2 Depending on sdmPos and Desired Clock Delay from SDM to Chop Clock .... 66 Register sdmClkCfgLp .................................................................................................................... 69 Register sdmClkCfgFp .................................................................................................................... 69 Register adcCoff ............................................................................................................................ 73 Register adcCgan ............................................................................................................................ 73 Register adcVoff ............................................................................................................................ 73 Register adcVgan ............................................................................................................................ 74 Register adcToff ............................................................................................................................ 74 Register adcTgan ............................................................................................................................ 74 Register adcPoCoGain .................................................................................................................... 75 Register adcCdat ............................................................................................................................ 76 Register adcVdat ............................................................................................................................ 76 Register adcTdat ............................................................................................................................ 76 Register adcRdat ............................................................................................................................ 76 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 7 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Table 3.36 Table 3.37 Table 3.38 Table 3.39 Table 3.40 Table 3.41 Table 3.42 Table 3.43 Table 3.44 Table 3.45 Table 3.46 Table 3.47 Table 3.48 Table 3.49 Table 3.50 Table 3.51 Table 3.52 Table 3.53 Table 3.54 Table 3.55 Table 3.56 Table 3.57 Table 3.58 Table 3.59 Table 3.60 Table 3.61 Table 3.62 Table 3.63 Table 3.64 Table 3.65 Table 3.66 Table 3.67 Table 3.68 Table 3.69 Table 3.70 Table 3.71 Table 4.1 Table 5.1 Data Sheet July 10, 2014 Register adcGain ............................................................................................................................ 77 Register adcCrcl ............................................................................................................................ 78 Register adcCrcv ............................................................................................................................ 78 Register adcVrcl ............................................................................................................................ 78 Register adcVrcv ............................................................................................................................ 78 Register adcCrth ............................................................................................................................ 80 Register adcCtcl ............................................................................................................................ 80 Register adcCtcv ............................................................................................................................ 80 Register adcCaccTh ........................................................................................................................ 81 Register adcCaccu .......................................................................................................................... 81 Register adcVTh............................................................................................................................... 82 Register adcVaccu .......................................................................................................................... 82 Register adcCmax ............................................................................................................................ 83 Register adcCmin ............................................................................................................................ 83 Register adcVmax ............................................................................................................................ 83 Register adcVmin ............................................................................................................................ 83 Register adcTmax ............................................................................................................................ 84 Register adcTmin ............................................................................................................................ 84 Register adcAcmp ............................................................................................................................ 85 Register adcGomd ............................................................................................................................ 86 Register adcSamp ............................................................................................................................ 86 adcMode Settings ............................................................................................................................. 87 Register adcCtrl ............................................................................................................................ 93 Register adcChan ............................................................................................................................ 98 Example Results of BIST .................................................................................................................. 99 Register adcDiag .......................................................................................................................... 100 Register currentSrcEna ............................................................................................................. 100 ZSSC1750 Register linCfg .......................................................................................................... 103 ZSSC1750 Register linShortFilter ........................................................................................ 104 ZSSC1750 Register linShortDelay ........................................................................................... 104 ZSSC1750 Register linWuDelay..................................................................................................... 104 OTP Memory Map .......................................................................................................................... 105 Register pullResEna .................................................................................................................... 107 Register versionCode .................................................................................................................. 107 Register pwrTrim .......................................................................................................................... 108 Register ibiasLinTrim ............................................................................................................... 108 ESD Protection According to AEC-Q100 Rev. G ........................................................................... 111 ZSSC1750/51 Pins Description ...................................................................................................... 113 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 8 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 1 IC Characteristics The absolute maximum ratings are stress ratings only. The ZSSC1750/51 might not function or be operable above the recommended operating conditions. Stresses exceeding the absolute maximum ratings might also damage the device. In addition, extended exposure to stresses above the recommended operating conditions might affect device reliability. ZMDI does not recommend designing to the “Absolute Maximum Ratings.” 1.1 Absolute Maximum Ratings Table 1.1 Absolute Maximum Ratings (referenced to VSSE) No Parameter Symbol Conditions Min Max Unit 1.1.1. External power supply VDDE VSSE-0.3 40 V 1.1.2. Current sensing, INP pin VINP VSSE-0.3 VDDA+0.3 V 1.1.3. Current sensing, INN pin VINN VSSE-0.3 VDDA+0.3 V 1.1.4. Voltage sensing, VBAT pin VVBAT -18 33 V 1.1.5. Voltage sensing, VBAT pin VVBAT -18 40 V 1.1.6. Temperature sensing, NTH pin VNTH VSSE-0.3 VDDA+0.3 V 1.1.7. Temperature sensing, NTL pin VNTL VSSE-0.3 VDDA+0.3 V 1.1.8. LIN bus interface, LIN pin VLIN -16 33 V 1.1.9. LIN bus interface, LIN pin VLIN -16 40 V VSSE-0.3 VDDP+0.3 V TAMB 125 °C 1.1.12. Junction temperature Tj 135 °C 1.1.13. Storage temperature TSTOR 125 °C 1.1.10. Digital IO pins 1.1.11. Ambient temperature under bias Data Sheet July 10, 2014 VIO 1h over lifetime 1h over lifetime -50 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 9 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 1.2 Recommended Operating Conditions Table 1.2 Operating Conditions No. Parameter Symbol Conditions Min Typ. Max Unit 1.2.1 Operating temperature range TAMB Ambient temperature; RTHJA=27K/W -40 115 °C 1.2.2 Extended temperature range TAMB_Ext Ambient temperature; reduced accuracies -40 125 °C 1.2.3 Supply voltage at BAT+ 1) terminal for normal operation VBAT+ 18 V 1.2.4 Minimum supply voltage at VDDE pin: a) When BAT+ < 6V, i.e. operation with low battery b) When VBAT = VDDE , i.e. without using Ddde and 1) Rdde VDDE_low 6 Normal accuracy for current and temperature measurements Reduced accuracy for voltage measurements Reduced accuracy for all measurements 13 4.8 V 4.2 1.2.5 Digital input voltage LOW VIL 0 0.3*VDDP V 1.2.6 Digital input voltage HIGH VIH 0.7*VDDP VDDP V 1) See application diagram on page 3. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 10 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 1.3 Electrical Parameters Note: See important notes at the end of the following table. See section 3.7 for definitions of the ULP and OFF power states. Table 1.3 No. Electrical Specifications Parameter Symbol Conditions Min Typ. Max Unit Supply 1.3.1. Average supply current at VDDE IDDE_avg Normal Mode (FP State, both ADCs on) 10 12 14 mA 1.3.2. Average power dissipation PDDE_avg Normal Mode, VDDE=13V 130 156 182 mW 1.3.3. Current at VDDE in Sleep Mode (ULP State with no measurement) 1.3.4. IDDE_slp TAMB = room temperature (RT) 55 µA TAMB = 115°C 100 µA Average current at VDDE in Comparator Mode (ULP State with wake-up interval = 30s and current ADC only) IDDE_cmp TAMB = RT 160 A 1.3.5. Average current at VDDE in OFF State (no measurements) IDDE_off TAMB = RT 50 µA 1.3.6. Internal analog power supply voltage, VDDA pin VDDA 2.4 2.5 2.6 V 1.3.7. Internal digital power supply voltage, VDDL pin VDDL 1.62 1.8 1.98 V Default 1.62 1.8 1.98 V Configuration option (see section 2.2) 1.08 1.2 1.32 V Default 2.97 3.3 3.63 V Configuration option (see section 2.2) 2.25 2.5 2.75 V - - 40 mA External Microcontroller (MCU) Supply 1.3.8. 1.3.9. 1.3.10. External microcontroller core power supply voltage, VDDC pin VDDC External microcontroller power supply voltage (periphery), VDDP pin VDDP Output current of VDDP regulator IVDDP_OUT Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 11 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) No. Parameter Symbol Conditions Min Typ. Max Unit 1.3.11. Output current capability of VDDP pin IVDDP See Figure 1.1 for test circuit - - 30 mA 1.3.12. Output current of VDDC regulator IVDDC_OUT 40 mA 1.3.13. Output current capability of VDDC pin IVDDC 40 mA Digital IO Pins Parameters (VDDP = 3.3V) 1.3.14. Input low-to-high threshold voltage VLH_th 55 60 65 % of VDDP 1.3.15. Input high-to-low threshold voltage VHL_th 35 40 45 % of VDDP 1.3.16. Internal pull-down resistor RPULL_down 70 190 310 k 1.3.17. Leakage current ILEAK_I/O - - 1 µA Output low level VOL IOUT = I_I/O - - 20 % of VDDP Output high level VOH IOUT = I_I/O 80 - - % of VDDP 1.3.18. 1.3.19. Vpin = VDDP 1.3.20. Output low level of SLEEPN pin VL_SLEEPN ISLEEPN = 0.1mA - - 0.40 V 1.3.21. Output high level of SLEEPN pin VH_SLEEPN ISLEEPN = 0.1mA 1.40 - - V MCU_CLK pin - - 3.0 mA All other IOs - - 1.5 mA SLEEPN pin - - 0.1 mA 4.5 5.5 6.5 pF 1.3.22. 1.3.23. Pin output current I_I/O 1) 1.3.24. 1.3.25. ISLEEPN Pin capacitance 1) C_I/O Current Channel 1.3.26. 1.3.27. Input signal range Input leakage current Data Sheet July 10, 2014 1) RangeC 1) ILEAK_C Gain = 4 -300 300 mV Gain = 8 -150 150 mV Gain = 16 -75 75 mV Gain = 32 -38 38 mV Gain = 64 -19 19 mV Gain = 128 -9.5 9.5 mV Gain = 256 -4.7 4.7 mV Gain = 512 -2.3 2.3 mV TAMB = 25°C -3 +3 nA © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 12 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) No. Parameter 1.3.28. Input offset current 1.3.29. Conversion rate 1) 1), 2) 1.3.30. Oversampling ratio (OSR) 4 (Sinc decimation filter) 1.3.31. No missing codes Integral nonlinearity 1.3.33. PGA gain range 1.3.34. Total gain error Conditions IOFFSET_C For input signal < 10mV RateC Programmable OSRC Programmable NMCC 1), 3) INL 1) 1) 1) 1.3.35. Gain drift 1.3.36. Offset error after calibration 1.3.38. Offset error drift July 10, 2014 Max Unit 0.5 1.5 nA 1 16000 Hz 32 256 Maximum input range 1) 1) 1) Bits ±10 ±60 APGA 4 512 errPGA_C -1 1 err_driftPGA_C Output noise with chop on Data Sheet Typ. 18 VOFFSET_C Normal Mode chop on, external short (VSSA) ppm of 4) FSR % ° ±3 Low-Power State, chop on, external short (VSSA) 1.3.37. Min 1) 1) 1.3.32. Symbol ppm/ C -2 2 µV -0.6 +0.6 µV o VOFFSET_DRIFT_C Chop on ±20 nV/ C Chop off ±80 nV/ C Gain = 512, conversion rate = 10Hz 1.1 µV Gain = 512, conversion rate = 1kHz 1.1 µV Gain = 32, conversion rate = 1kHz 3 µV Gain = 4, conversion rate = 1kHz 11 µV VNOISE_C © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. o RMS RMS RMS RMS 13 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) No. 1.3.39. 1.3.40. Parameter Current offset Resolution 1) Symbol Conditions IBAT_offset Chop on, gain = 512, Rshunt = 100µ 1) IRES Chop on, gain = 512, Rshunt = 100µ Min Typ. Max Unit 10 mA 1 mA Voltage Channel 1.3.41. Input signal range (at VBAT pin) 1.3.42. Input measurement range 1.3.43. Input valid range for ADC 1.3.44. Voltage resistive divider ratio 1.3.45. Resistor divider mismatch drift 1.3.46. Conversion rate 1.3.47. Oversampling ratio 4 1) (Sinc decimation filter) 1.3.48. No missing codes 1) 1) 1), 2) 1) Integral nonlinearity 1.3.50. Total gain error (includes resistor divider mismatch) 1.3.51. Gain drift 1.3.52. Offset error after calibration: 1) Normal Mode 1) Data Sheet July 10, 2014 1) Offset error drift 1) RangeV Resistive divider (1:24) 0 28.8 V Rangemeas_V Resistive divider (1:24) 3.6 28.8 V RangeADC_V Resistive divider (1:24) 0.15 1.2 V RatioV 24 Ratio_misdrift_v ±3 Programmable 1 16000 OSRV Programmable 32 256 INLV 18 Maximum input range errPGA_V Hz Bits ±10 -0.25 err_driftPGA_V 1) º ppm/ C RateV NMCV 1), 3) 1.3.49. 1.3.53. 1) 1) ±60 ppm of 4) FSR 0.25 % ±3 ppm/°C Chop on external short (1.25V) 200 µV Chop off external short (1.25V) 1 mV VOFFSET_DRIFT_V Chop on ±10 µV/°C Chop off ±20 µV/°C VOFFSET_V © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 14 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) No. 1.3.54. Parameter Output noise 1) Symbol Conditions VNOISE_V Min Typ. Max Chop on gain = 1, conversion rate =10Hz 30 50 Chop on gain = 1, conversion rate = 1kHz 1 Unit RMS µV RMS µV Temperature Channel (External NTC/Reference Resistor and Internal Temperature Sensor) 1.3.55. Voltage drop over NTC resistor 1.3.56. Voltage drop over reference 1) resistor 1.3.57. Conversion rate 1.3.58. Oversampling ratio 4 1) (Sinc decimation filter) 1.3.59. Integral nonlinearity 1.3.60. No missing codes 1.3.61. Offset error after ZSSC1750/51 1) calibration 1.3.62. Offset error drift 1) 1), 3) 1) 1) Output noise 1.3.64. Resistor to ground at pin NTL 1.3.65. Internal temperature sensor 1) resolution Linearity error of internal 1) temperature sensor 1.3.66. Data Sheet July 10, 2014 VNTC 0 1.2 V VREF_Res 0 1.2 V Hz RateT Programmable 1 16000 OSRT Programmable 32 256 INLT Maximum input range NMCT 1) 1.3.63. 1) VOFFSET_T ±60 16 ppm of FSR Bit Normal Mode, chop on, external short (1.25V) -100 100 µV Normal Mode, chop off, external short (1.25V) -2 2 mV o VOFFSET_DRIFT_T Chop on ±10 µV/ C Chop off ±20 µV/ C VNOISE_T 1) ±10 Chop on, gain = 1, conversion rate =500Hz o 50 GNDRES 50 RMS µV k RESITS - 1/32 - °C/LSB LEITS - ±2 - °C © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 15 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) No. Parameter Symbol Conditions Min Typ. Max Unit 2.75 3.0 3.6 V Power-on Reset (POR) 1.3.67. Power-on reset threshold VPORB At VDDE 1.3.68. Power-on-reset hysteresis HystPORB At VDDE 1.3.69. Low-voltage flag low_voltage At VDDE 1) 1.3.70. VDDP high (for VDDP = 3.3V configuration) 1.3.71. VDDP high hysteresis 1) vddp_high HystVDDP_high At VDDE 300 mV 1.8 2.0 2.3 V 3.9 4.05 4.2 V At VDDE 400 mV Low-Power Voltage Reference 1.3.72. Reference bandgap voltage: low-power 1.3.73. Accuracy (including temperature drift) 1.3.74. Temperature coefficient 1) VBGL 1.16 1.32 V -3 3 % TCVBGL 50 ppm/K fLPO 125 kHz Low-Power (LP) Oscillator 1.3.75. Frequency 1.3.76. Accuracy (including temperature 1) drift) -3 3 % Uncalibrated 1.16 1.32 V Calibrated -20 +20 ppm/K High-Precision Voltage Reference 1.3.77. Reference bandgap voltage: high-precision 1.3.78. Temperature coefficient 1) VBGH TCVBGH ±5 High-Precision (HP) Oscillator 1.3.79. Frequency 1.3.80. Accuracy 1) (including temperature drift) fHPO 20 MHz -1 1 % 200 mA LIN Interface IBUS_LIM LIN spec 2.1 Param 12 40 Input leakage current, dominant 1) state, driver off IBUS_PAS_dom LIN spec 2.1 Param 13 -1 Input leakage current, recessive 1) state, driver off IBUS_PAS_rec LIN spec 2.1 Param 14 1.3.81. Current limitation for driver 1) dominant state 1.3.82. 1.3.83. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. mA 20 µA 16 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) No. Parameter Symbol 1.3.84. Control unit disconnected from 1) ground 1.3.85. VBAT supply disconnected 1.3.86. Conditions Min Typ. Max Unit 1 mA IBUS_NO_GND LIN spec 2.1 Param 15 IBUS_NO_BAT LIN spec 2.1 Param 16 100 µA Receiver dominant state, 1) VDDE > 7V VBUSdom LIN spec 2.1 Param 17 0.4 VDDE 1.3.87. Receiver recessive state, 1) VDDE > 7V VBUSrec LIN spec 2.1 Param 18 0.6 1.3.88. Center of receiver threshold 1) VBUS_CNT LIN spec 2.1 Param 19 0.475 1.3.89. Receiver hysteresis voltage 1) VHYS LIN spec 2.1 Param 20 1.3.90. Voltage drop at serial diodes VSerDiode LIN spec 2.1 Param 21 1.3.91. Battery shift 1) VSHIFT_BAT 1.3.92. Ground shift 1) 1.3.93. Difference between battery shift 1) and ground shift 1.3.94. LIN pull-up resistor 1.3.95. Duty cycle 1 1) 1.3.96. Duty cycle 2 1) 1.3.97. Duty cycle 3 1) 1.3.98. Duty cycle 4 1) 1.3.99. Receiver propagation delay 1) Data Sheet July 10, 2014 VDDE 0.525 VDDE 0.175 VDDE 1 V LIN spec 2.1 Param 22 0.115 VBAT VBUS_GND LIN spec 2.1 Param 23 0.115 VBAT VSHIFT_Difference LIN spec 2.1 Param 24 0 8 % RSLAVE LIN spec 2.1 Param 26 20 47 k D1 LIN spec 2.1 Param 27 0.396 D2 LIN spec 2.1 Param 28 D3 LIN spec 2.1 Param 29 D4 LIN spec 2.1 Param 30 0.590 TRX_pdr LIN spec 2.1 Param 31 6 µs TRX_sym LIN spec 2.1 Param 32 2 µs 1) 1) 1) 1.3.100. Symmetry receiver propagation 1) delay, rising/falling edge -1 0.4 0.5 0.7 30 0.581 0.417 -2 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 17 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) No. Parameter Symbol 1.3.101. Capacitance of slave node 1.3.102. LIN pin capacitance 1) 2) 3) 4) 1) Min Typ. LIN spec 2.1 Param 23 CSLAVE 1) Conditions CLIN - - Max Unit 250 pF 30 pF Not tested in production test; given by design and/or characterization. Depends on chopping and OSR settings. FSR = 1.2V FSR = Full-scale input range of the ADCs. The input range is given in specification 1.3.26 for current, 1.3.41 for voltage, and 1.3.55 and 1.3.56 for external temperature. Figure 1.1 Measurement Method for Determining VDDP Pin Current Capability IVDDP_OUT IVDDP VDDP IIO=10mA Digital IOs ZSSC1750/51 VDDP VDD External MCU VSS VSSN Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 18 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 1.4 Timing Parameters Table 1.4 Timing Parameters No Parameter Symbol Conditions Min Typ Max Unit fSPI - - 8 MHz tSCLKPreg 125 - - ns tSCLKPotp 200 - - ns tSCLKW 40 50 60 SPI Protocol Timing (See Figure 1.2) 1) 1.4.1. SPI operational frequency 1.4.2. SCLK clock period for registers 1) read/write 1.4.3. SCLK clock period for OTP read 1.4.4. SCLK clock pulse width 1) 1) % tSCLKP 1) 1.4.5. CSN setup time 1.4.6. CSN hold time 1.4.7. CSN high time 1.4.8. MOSI data setup time 1.4.9. MOSI data hold time 1.4.10. tCSU 50 - - ns 1) tCHD 50 - - ns 1) tCHI 300 - - ns tDSU 20 - - ns tDHD 10 - - ns tDACC - - 25 ns 6553.5 s 466 h 1) 1) MISO data access time 1) Timer 0 (Sleep Timer) 1) 1.4.11. Time interval 1.4.12. Time interval with post-scaler 1.4.13. Resolution 1) 1) SLPTI1 Programmable SLPTI2 Programmable 0.1 SLPTI1res 100 ms Timer 1 (Watchdog Timer WDT) 1.4.14. 1.4.15. Time interval Resolution 1) 1) WDTI WDTIres Programmable 8µ Programmable 0.008 6553.5 s 100 ms 1 ms Startup Timing (See Figure 1.3) 1.4.16. 1) PORB delay until analog blocks 1) settled TPORB_dly Not tested in production test; given by design and/or characterization. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 19 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 1.2 SPI Protocol Timing tCHI tSCLKP CSN tCSU tSCLKW tCHD SPI_CLK tDSU tDHD MOSI 7 (MSB) 0 (LSB) tDACC MISO Data Sheet July 10, 2014 7 (MSB) 0 (LSB) © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 20 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 1.3 ZSSC1750/51 Power-Up and Power-Down Sequence VDDE TYP VPORBmax VPORBmin t VDDL t PORB at STO pin t TPORB_dly VDDC t VDDP t VDDA t STATE ADC measurements can run Data Sheet July 10, 2014 SBC Digital SBC Analog OFF MCU OFF OFF Supplied Supplied Running Settled Running OFF OFF OFF © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 21 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 2 Circuit Description 2.1 Overview The ZSSC1750/51 is a data acquisition System Basis Chip (SBC) assembled in a PQFN36 6x6mm package. It contains a high voltage circuit, analog input stage including peripheral blocks, sigma-delta (ΣΔ) ADCs (SD_ADC), digital filtering, and a LIN transceiver (for ZSSC1750 only). Communication between an external microcontroller and the SBC is handled by a Serial Peripheral Interface (SPI). The functions of the ZSSC1750/51 are controlled by register settings. The circuit starts after power-on with default register and calibration settings that can be overwritten by the user’s software. One input channel measures IBAT via the voltage drop at the external shunt resistor. The second channel measures VBAT and the temperature. By simultaneously measuring VBAT and IBAT, it is possible to dynamically determine Rdi, which is correlated with the state of health (SOH) of the battery. By integrating IBAT, it is possible to determine the state of charge (SOC) of the battery. These are the fundamental parameters for an intelligent battery sensor. The necessary microcontroller and the software for determining these parameters is not part of the ZSSC1750/51. Figure 2.1 Functional Block Diagram Common Ground VBAT Analog Block ZSSC1750/51 Analog Front End SBC LP_REG VDDP_REG BG_REF WD_TIMER Digital Block IRQ_CTRL VDDE VDDC VDDA VDDA_REG VDDC_REG SBC_PMU GP_TIMER OSC DIGITAL FILTER CONFIG REGISTER RESULT REGISTER SLEEPN WDT_DIS INP SHUNT VDDP SD_ADC INN PGA VBAT MCU_CLK MCU_RSTN IRQN RREF + – BATTERY SD_ADC NTH DIGITAL FILTER CALIBRATION DATA PATH SPI MUX CSN SCLK MISO MOSI NTC NTL LIN LIN_PHYS (1) LIN 1) RXD TXD Available in ZSSC1750 only. During the Standby Mode and the system’s Sleep Mode (e.g., engine is off), the system periodically measures the values to monitor the discharge of the battery (see section 3.7 regarding modes). Measurement cycles are controlled by the user’s software and are dependent on the detected events. The ZSSC1750/51 is designed for low current consumption during Sleep Mode in the range of less than 60µA. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 22 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 2.2 SBC-to-MCU Interface Pins The ZSSC1750/51 connects to the external microcontroller (MCU) using pins shown in Figure 2.2-A. ZSSC1750/51 pins can be classified in three categories: digital IOs, microcontroller supply pins, and the power state indicator pin. Figure 2.2 ZSSC1750/51 Digital IO Interface ZSSC1750/51 VDDC VDDC VDDP VDDP VDDP DigIO MCU_CLK OSC 20MHz MCU_RSTN POR & WDT WDT_DIS Optional MCU clock External MCU reset: - Power-on Reset - Watchdog Timer (with external disable) To core Pull-down enable Digital Input Rpull_down ULP state à DIS OFF state à DIS Core and periphery supply for extenal MCU VSSN IRQN IRQ ctrl ZSSC1750/51 IRQ to external MCU interrupt pin B) Structure of ZSSC1750/51 digital input CSN SCLK VDDP SPI MOSI Serial Peripheral Interface to MCU master SPI pins MISO LIN PHY RXD Digital Out From core TXD To MCU LIN UART VSSN VDDL VSSN VSSN ZSSC1750/51 digital ground VSSN PMU SLEEPN C) Structure of ZSSC1750/51 digital output Power mode indicator pin or disable signal for ext. regulators VSSN A) ZSSC1750/51 external MCU interface Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 23 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 2.2.1 Digital I/Os The digital I/O pins include the SPI interface pins, MCU clock, rest and interrupt pins, LIN UART pins (for ZSSC1750 only), and watchdog timer disable pin. All digital input pins of the ZSSC1750/51 feature a Schmitt trigger (see Figure 2.2-B), as well as configurable pull-down resistors and protection diodes. The pull-down resistors have values specified by parameter 1.3.16. They are enabled after power-on-reset and can be further controlled via the pullResEna register (see section 3.11.1.1). All digital output pins of the ZSSC1750/51 have a push-pull stage and protection diodes connected as shown in Figure 2.2-C. All digital I/Os are supplied by the VDDP voltage, which is switched off when the ZSSC1750/51 is in the ULP or OFF State (see section 2.3); i.e. the I/Os are also off in this state. Note: In order to avoid parasitic supply of the digital I/O circuitry when the ZSSC1750/51 is in the ULP or OFF State, the digital outputs of the external microcontroller should be disabled. This is valid when the external microcontroller is not supplied by the ZSSC1750/51. 2.2.2 External Microcontroller (MCU) Supply Pins The ZSSC1750/51 provides two separate regulators for the external microcontroller supply. The VDDP regulator provides 3.3V, and VDDC provides 1.8V. Both voltages are switched off when the ZSSC1750/51 is in the ULP or OFF State. For more information regarding the VDDP and VDDC regulators, including trimming options, refer to sections 3.12.5 and 3.12.6. The current capability of the VDDP and VDDC pins is specified by parameters 1.3.11 and 1.3.13 respectively. 2.2.3 SLEEPN Power State Indicator Pin The ZSSC1750/51 features a SLEEPN pin that indicates the power state of the ZSSC1750/51 (see section 2.3). When the ZSSC1750/51 is in the full power (FP) state or low power (LP) state, the SLEEPN pin is HIGH; when the state is ULP or OFF, SLEEPN is LOW. In order to remain powered in these states, the SLEEPN pin circuitry is supplied by the VDDL regulator. When HIGH, the SLEEPN pin has a 1.8V output voltage level; the HIGH and LOW levels are specified with parameters 1.3.20 and 1.3.21. In the application, the SLEEPN pin can be connected to the external microcontroller (if it remains powered in system Sleep Mode), or it can be used for disabling an external circuitry when the ZSSC1750/51 goes into one of the power saving modes. Depending on the application specifics, an external buffer (e.g., a transistor) might be needed for the SLEEPN pin for a proper level or current conditioning. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 24 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 2.3 System Power States There are four different power states implemented in the ZSSC1750/51 as illustrated in Figure 2.3. Full details are given in section 3.7. Figure 2.3 ZSSC1750/51 Power States FP LP ULP 6060 OFF 2.3.1 Full Power State (FP) The ZSSC1750/51 enters the Full Power (FP) State after power-on reset or after wake-up. In this power state, the ZSSC1750/51 is fully operational and the external microcontroller is supplied and running (see section 3.7). In the FP State, the ADCs are fully powered and running on the 4MHz base clock, which is generated from the 20MHz high-precision oscillator. Of the four power states, the FP State consumes the most power. The MCU software can trigger the power management unit (PMU) inside the ZSSC1750/51 to enter any other power state (see section 3.7). 2.3.2 Low Power State (LP) The Low Power (LP) State is intended for scenarios where the ZSSC1750/51 will only perform low-power measurements without any operation by the external microcontroller (MCU). For its ADC operations, it uses a 125kHz clock from the low-power oscillator as the base clock. The system can wake up from this power state via any enabled interrupt of the SBC as well as via an MCU reset generated by the watchdog timer. Note: For any SBC interrupt source that will wake up the system, the corresponding interrupt source must be enabled in the SBC. Note that the SBC rejects the power-down command when an enabled interrupt source inside the SBC is already active. When the system enters the LP State from the FP State, the microcontroller software must first enable the required interrupt sources for later wake-up in the ZSSC1750/51 SBC and the microcontroller and it must set the pdState bit in the pwrCfgLp register (see Table 3.19) followed by a gotoPd command (see section 3.7 and Table 3.20). A rising edge on the CSN line triggers the SBC to enter its LP State. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 25 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) When any of the enabled interrupts becomes active, the system returns to the FP State and continues the software execution. Note: Do not release the CSN line by software at the end of sending a power-down command to avoid the MCU clock being stopped by the SBC at an intermediate state. 2.3.3 Ultra Low Power State (ULP) The Ultra-Low Power (ULP) State is similar to the LP State except that the SBC also disables the power for the external microcontroller. This power state is intended for scenarios where the SBC will only perform low-power measurements without any operation running on the microcontroller. For the ZSSC1750/51’s ADC operations in this state, it uses a 125kHz clock from the low-power oscillator as the base clock. The system can wake up from this power state by any enabled interrupt of the SBC. The microcontroller is reset upon wake up by the SBC to guarantee correct start up. This means that the microcontroller software starts again from address 0HEX after wake up, not at the position where it was stopped. Note: For any SBC interrupt source that will wake up the system, the corresponding interrupt source must be enabled in the SBC. Note that the SBC rejects the power-down command when an enabled interrupt source inside the SBC is already active. When the system enters the ULP State from the FP State, the microcontroller software must first enable the required interrupt sources for later wake-up in the SBC and the microcontroller and it must set the pdState bit in pwrCfgLp register (see Table 3.19) followed by a gotoPd command (see section 3.7 and Table 3.20). A rising edge on the CSN line triggers the SBC to enter its ULP State. When any of the enabled interrupts becomes active, the system returns to FP State and restarts the microcontroller software execution. Note: Do not release the CSN line by software at the end of sending a power-down command to avoid the microcontroller clock being stopped by the SBC at an intermediate state. 2.3.4 OFF Power State The OFF power state has the lowest power consumption: no measurements can be performed as all oscillators are stopped. This power state is intended for scenarios where no measurements will be performed and the system will consume as little power as possible. The system can wake up from this power state only by receiving a wakeup frame over the LIN interface (only for the ZSSC1750) or after a power-on reset (for ZSSC1750/51). The external microcontroller is reset at wake up by the SBC to guarantee correct start up. This means that the microcontroller’s software starts again from address 0HEX after wake up, not at the position where it was stopped. Note: For any SBC interrupt source that will wake up the system, the corresponding interrupt source, e.g. the LIN wakeup interrupt (for the ZSSC1750 only), must be enabled inside the SBC. Note that the SBC rejects the power-down command when an enabled interrupt source in the SBC is already active. When the system enters the OFF power state from the FP State, the microcontroller software must first enable the required interrupt source in the SBC, e.g. the LIN interrupt (for the ZSSC1750 only), and the microcontroller and must set the PdState bit in register pwrCfgLp (see Table 3.19) followed by a gotoPD command (see Table 3.20). A rising edge on the CSN line triggers the SBC to enter its OFF State. When any of the enabled interrupts becomes active, the ZSSC1750/51 returns to the FP State and the external microprocessor can restart its software execution. Note: Do not release the CSN line by software at the end of sending a power-down command to avoid the MCU clock being stopped by the SBC at an intermediate state. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 26 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3 ZSSC1750/51 Functional Block Descriptions 3.1 Serial Peripheral Interface (SPI Slave) The ZSSC1750/51 is fully controllable by an external microcontroller via an integrated four-wire SPI slave. It only operates in a single mode when both the clock polarity and the clock phase are 1 (the clock is high when inactive, data is sent on the falling SPI clock edge, and data is sampled on the rising SPI clock edge). The accessible registers of the SBC as well as the one-time programmable (OTP) memory can be read via the SPI. The internal status information of the SBC is also shifted-out during the address and length bytes of the implemented SPI protocol (see Figure 3.1). Read and write burst accesses of up to 128 bytes are supported. The SPI chip-select line CSN must be low during any transfer until the complete transfer has finished. This is needed as the CSN input is not only used as an enable signal but also as an asynchronous reset for part of the SPI front-end. The reason for this is to be able to set the SPI back to a defined state via the microcontroller as well as to extract status information without needing to access any register. The CSN input can be kept low between two transfers. The CSN input must only be driven high for execution of the “go-to-power-down” command after the required register settings have been completed. Note: A high level at CSN resets the internal SPI state machine. 3.1.1 SPI Protocol The SPI slave module only operates with a clock polarity of 1 (SCLK is high when no transfer is active) and with a clock phase of 1 (data is sent on the falling edge; data is sampled on the rising edge). For any access, the CSN input must be low. At the end of any read access, the CSN input can be kept low. For write accesses that change the power state, the CSN input must be driven high at the end of the write access; it can be kept low for write accesses to other registers. During an SPI access, the CSN input must be kept low. Important: Driving the CSN input high during a read transfer can cause a loss of data. In each SPI transfer, 1 to 128 bytes can be read or written in one burst access. All bytes are sent and received with the MSB first. As shown in Figure 3.1, each SPI transfer starts with two bytes sent by the master while the slave sends back status information in parallel. The first of the two bytes sent by the master is the address byte containing the first address to be accessed. When multiple bytes are read or written, the received SPI address is internally incremented for each data byte. The second byte starts with the access type of the transfer (1 = write; 0 = read) followed by the 7-bit length field indicating the number of data bytes that will be read or written. The exception is the length value of 0, which is interpreted by the slave SPI as 128 bytes. The status information sent back by the slave during the address and length bytes starts with a fixed value of AHEX. This can be used to detect whether the connection is still present. The next bits sent are the slave status word (SSW), which is 12 bits of actual status information. The 12 SSW bits have the following definitions: SSW[11]: Value of the low-voltage flag SSW[10:8]: Reset status SSW[7]: Watchdog active flag SSW[6]: Low-power oscillator trimming circuit active SSW[5]: Voltage/temperature ADC active Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 27 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) SSW[4]: Current ADC active SSW[3]: LIN short protection active (applicable for ZSSC1750 only) SSW[2]: LIN TXD timeout protection active (applicable for ZSSC1750 only) SSW[1]: Readable sleep timer value valid SSW[0]: OTP download procedure active Note: After the external microcontroller has been reset, the user’s software can read the low-voltage flag and the reset status by a single-byte transfer (important: send only the address byte) to shorten the initialization phase (e.g., when a reset was caused by a wake-up event) without needing to read or write further bytes including the length byte. After the address byte and length byte are sent by the master, either the master (write transfer) or the slave (read transfer) is transmitting data. The slave ignores all incoming bits while it is sending the requested number of data bytes (read), and the data bytes returned during a write transfer have no meaning. Figure 3.1 shows a read and a write burst access to the SBC. Figure 3.1 Read and Write Burst Access to the SBC Read Access SCLK CSN MOSI A[7:0] R L[6:0] MISO SSW[11:0] D0[7:0] DL-1[7:0] D0[7:0] DL-1[7:0] Write Access SCLK CSN MOSI A[7:0] W L[6:0] MISO SSW[11:0] A: R: W: L: SSW: SCLK: Data Sheet July 10, 2014 Start address of SPI access Read access (MSB of second byte is low) Write access (MSB of second byte is high) Number of data bytes (0 = 128 bytes) Slave status word SPI clock © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 28 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.2 SBC Register Map (RESULT REGISTER Block and CONFIG REGISTER Block) Table 3.1 defines the registers in the SBC. In the “Access” column, the following abbreviations indicate the read/write status of the registers: RC = read-clear; RO = read-only; RW = readable and writable; WO = writeonly; W1C = write-one-to-clear, RWS = read-write-set. For more details, see the subsequent sections for the individual registers in section 3. Important: There is a distinction between “unused” and “reserved” addresses. No problem occurs when writing to unused addresses, but writing 0HEX to unused addresses for future expansions is recommended. Reserved addresses must always be written with the given default value. Table 3.1 Name irqStat adcCdat adcVdat adcRdat adcTdat adcCaccu adcVaccu adcCmax adcCmin Data Sheet July 10, 2014 SBC Register Map Address Order Default Access Short Description 00HEX LSB 00HEX RC 01HEX MSB 00HEX RC 02HEX LSB 00HEX RO 03HEX --- 00HEX RO 04HEX MSB 00HEX RO 05HEX LSB 00HEX RO 06HEX --- 00HEX RO 07HEX MSB 00HEX RO 08HEX LSB 00HEX RO 09HEX MSB 00HEX RO 0AHEX LSB 00HEX RO 0BHEX MSB 00HEX RO ADC result register of a single temperature measurement by reading a voltage across the NTC resistor (external temperature measurement) or of a differential voltage (VPTAT – VBGH; internal temperature measurement) 0CHEX LSB 00HEX RO Accumulator register for current measurements 0DHEX --- 00HEX RO 0EHEX --- 00HEX RO 0FHEX MSB 00HEX RO 10HEX LSB 00HEX RO 11HEX --- 00HEX RO 12HEX MSB 00HEX RO 13HEX LSB 00HEX RO 14HEX MSB 80HEX RO 15HEX LSB FFHEX RO 16HEX MSB 7FHEX RO Interrupt status register ADC result register of a single current measurement ADC result register of a single voltage measurement ADC result register of a single temperature measurement by reading a voltage across the reference resistor (external temperature measurement only) Accumulator register for voltage measurements Maximum current value measured in configured measurement sequence Minimum current value measured in configured measurement sequence © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 29 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Name Address Order Default Access 17HEX LSB 00HEX RO 18HEX MSB 80HEX RO 19HEX LSB FFHEX RO 1AHEX MSB 7FHEX RO 1BHEX LSB 00HEX RO 1CHEX MSB 00HEX RO adcCtcv 1DHEX --- 00HEX RO Counter register containing the number of current measurements greater than or equal to the threshold adcVrcv 1EHEX --- 00HEX RO Counter register containing the number of voltage measurements Unused 1FHEX --- 00HEX --- --- sleepTCurCnt 20HEX LSB 00HEX RO Current sleep timer value 21HEX MSB 00HEX RO Unused 22HEX to 2FHEX --- 00HEX --- adcCgan 30HEX LSB 00HEX RW 31HEX --- 00HEX RW 32HEX MSB 80HEX RW 33HEX LSB 00HEX RW 34HEX --- 00HEX RW 35HEX MSB 00HEX RW 36HEX LSB 00HEX RW 37HEX --- 00HEX RW 38HEX MSB 80HEX RW 39HEX LSB 00HEX RW 3AHEX --- 00HEX RW 3BHEX MSB 00HEX RW 3CHEX LSB 00HEX RW 3DHEX MSB 80HEX RW 3EHEX LSB 00HEX RW 3FHEX MSB 00HEX RW 40HEX LSB 00HEX RW 41HEX MSB 00HEX RW adcVmax adcVmin adcCrcv adcCoff adcVgan adcVoff adcTgan adcToff adcCrcl Data Sheet July 10, 2014 Short Description Maximum voltage value measured in configured measurement sequence Minimum voltage value measured in configured measurement sequence Counter register containing the number of current measurements --Digital gain correction for current channel Digital offset correction for current channel Digital gain correction for voltage channel Digital offset correction for voltage channel Digital gain correction for temperature channel Digital offset correction for temperature channel Number of current measurements before the ready strobe is generated © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 30 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Name Address Order Default Access Short Description 42HEX LSB 00HEX RW 43HEX MSB 00HEX RW Absolute current value is compared to this threshold in Current Threshold Comparator Mode adcCtcl 44HEX --- 00HEX RW Number of current measurements greater than or equal to the threshold before the set interrupt strobe is generated adcVrcl 45HEX --- 00HEX RW Number of voltage measurements before ready strobe is generated adcVth 46HEX LSB 00HEX RW 47HEX MSB 00HEX RW Voltage threshold level for Threshold Comparator (unsigned) or Accumulator (signed) Modes 48HEX LSB 00HEX RW 49HEX --- 00HEX RW 4AHEX --- 00HEX RW 4BHEX MSB 00HEX RW adcTmax 4CHEX --- 00HEX RW Upper threshold for temperature measurement adcTmin 4DHEX --- 00HEX RW Lower threshold for temperature measurement adcAcmp 4EHEX LSB 30HEX RW ADC function enable register 4FHEX MSB 00HEX RW adcGomd 50HEX --- 10HEX RW Reference voltage and sigma-delta modulator (SDM) configuration (see section 3.8) adcSamp 51HEX --- 00HEX RW Oversampling and filter configuration adcGain 52HEX --- 00HEX RW Gain configuration register for analog amplifiers pwrCfgFp 53HEX --- 00HEX RW Power configuration register for Full Power (FP) State irqEna 54HEX LSB 00HEX RW Interrupt enable register 55HEX MSB 00HEX RW adcCtrl 56HEX --- 00HEX RW ADC control register for Full Power State (FP) adcPoCoGain 57HEX --- 00HEX RW Post-correction gain configuration 58HEX - 5EHEX --- 00HEX --- discCvtCnt 5FHEX --- 00HEX RW Configuration register for some power-down states sleepTAdcCmp 60HEX LSB 00HEX RW Compare value for ADC trigger timer 61HEX MSB 00HEX RW 62HEX LSB 00HEX RW 63HEX MSB 00HEX RW 64HEX --- 20HEX RW adcCrth adcCaccth Unused sleepTCmp pwrCfgLp Data Sheet July 10, 2014 Accumulator threshold for current channel --- Compare value for sleep timer Power configuration register for power-down states © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 31 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Name Address Order Default Access gotoPd 65HEX --- 00HEX WO Unused 66HEX to 67HEX --- 00HEX --- cmdExe 68HEX --- 02HEX WO/RW Unused 69HEX to 6FHEX --- 00HEX --- --- wdogCnt 70HEX LSB FFHEX RO Current watchdog counter value 71HEX MSB FFHEX RO 72HEX LSB FFHEX RW 73HEX MSB FFHEX RW wdogCfg 74HEX --- 09HEX RW Unused 75HEX to 77HEX --- 00HEX --- --- 78HEX LSB 00HEX RO Result counter of low-power oscillator trim circuit 79HEX MSB 00HEX RO irefLpOsc 7AHEX --- 52HEX RW Trim value for low-power oscillator lpOscTrim 7BHEX --- 04HEX RW Configuration register for trim circuit of LP oscillator 7CHEX to 7FHEX --- 00HEX --- 80HEX --- 00HEX WO 81HEX to AFHEX --- 00HEX --- B0HEX LSB 18HEX RW B1HEX MSB 00HEX RW B2HEX LSB 08HEX RW B3HEX MSB 90HEX RW B4HEX --- 00HEX RW/W1C wdogPresetVal lpOscTrimCnt Unused swRst Unused sdmClkCfgLp sdmClkCfgFp Short Description Power-down activation register --Command execution register Preset value for watchdog counter Configuration register for watchdog counter --Software reset --Clock configuration for SDM clock in power-down state Clock configuration for SDM clock in Full-Power State (FP) ZSSC1750: Configuration for LIN control logic linCfg ZSSC1751: Not used Important: Must remain as default for ZSSC1751 ZSSC1750: Configuration for LIN short debounce filter linShortFilter B5HEX --- 0FHEX RW ZSSC1751: Not used Important: Must remain as default for ZSSC1751 ZSSC1750: Configuration for LIN short TX-RX delay linShortDelay Data Sheet July 10, 2014 B6HEX --- 4FHEX RW ZSSC1751: Not used Important: Must remain as default for ZSSC1751 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 32 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Name Address Order Default Access Short Description ZSSC1750: Configuration for LIN wake-up time linWuDelay B7HEX --- 14HEX RW ZSSC1751: Not used Important: Must remain as default for ZSSC1751 pullResEna B8HEX --- FFHEX RW Configuration register for pull-down resistors funcDis B9HEX --- 00HEX RW Disable bits for dedicated functions versionCode BAHEX LSB 01HEX RO Version code BBHEX MSB 03HEX RO Unused BCHEX - BFHEX --- 00HEX --- pwrTrim C0HEX --- 7CHEX RW Trim bits for voltage regulators and bandgap irefOsc C1HEX LSB 10HEX RW Trim values for high-precision oscillator C2HEX MSB 40HEX RW C3HEX --- ibiasLinTrim --- ZSSC1750: Bias current trim register for LIN block 10HEX RW ZSSC1751: Not used Important: Must remain as default for ZSSC1751 Reserved C4HEX --- 00HEX RW --- Reserved C5HEX --- 00HEX RW --- Reserved C6HEX --- 00HEX RW --- Reserved C7HEX --- 00HEX RW --- Reserved C8HEX --- 00HEX RW --- Reserved C9HEX --- 00HEX RW --- Reserved CAHEX --- 08HEX RW --- Reserved CBHEX --- 00HEX RW --- Reserved CCHEX --- 00HEX RW --- Reserved CDHEX --- 00HEX RW --- Reserved CEHEX --- 00HEX RW --- Reserved CFHEX --- 00HEX RW --- adcChan D0HEX --- 00HEX RW Analog multiplexer configuration during test/ diagnosis adcDiag D1HEX --- 80HEX RW Enable register for test/diagnosis currentSrcEna D2HEX --- 00HEX RW Enable register for current sources Reserved D3HEX --- 00HEX RW --- Reserved D4HEX --- 00HEX RW --- Reserved D5HEX --- 00HEX RW --- Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 33 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Name Address Order Default Access Reserved D6HEX --- 00HEX RW --- Reserved D7HEX --- 00HEX RW --- Reserved D8HEX --- 00HEX RW --- Reserved D9HEX --- 00HEX RW --- Reserved DAHEX --- B8HEX RW --- Reserved DBHEX --- 00HEX RW --- Reserved DCHEX --- 00HEX RW --- Reserved DDHEX --- 00HEX RW --- Reserved DEHEX --- 00HEX RW --- Reserved DFHEX --- 00HEX RW --- E0HEX to FFHEX --- --- RO OTP raw data (see section 3.10.) OTP 3.3 3.3.1 Short Description ZSSC1750/51 Clock and Reset Logic Clock Sources The ZSSC1750/51 SBC contains two different oscillators, a low-power oscillator (LP oscillator) providing a clock of 125kHz (typical) with an accuracy of ±3% and a high-precision oscillator (HP oscillator) providing a clock of 20MHz (typical) with an accuracy of ±1%. The low-power oscillator is always active except in the OFF State while the high-precision oscillator is only active in Full-Power State (FP). The clock from the high-precision oscillator is routed to the external microcontroller via the MCU_CLK pin. There are three different internal clocks generated from the two clocks from the oscillators for the digital core of the SBC: Low-power clock (lpClk): This clock is directly driven by the low-power oscillator and has a frequency of 125kHz. It is used for the watchdog timer, the sleep timer, and the power management unit. Divided clock (divClk): This clock is derived from the high-precision oscillator and has a frequency of 4MHz. It is used for the register file, the low-power oscillator trimming circuit, the LIN support logic (ZSSC7150 only), and the OTP controller. Multiplexed clock (muxClk): This clock is identical to the divClk in the Full-Power State (FP) and identical to lpClk in the LP and ULP States. It is used for the ADC controller unit and the interrupt controller. Both oscillators are trimmed during the production test, and the trim values are stored in the OTP memory (IREF_OSC_0, IREF_OSC_1, IREF_OSC_2, IREF_OSC_3, IREF_LP_OSC; see Table 3.67). The high precision oscillator is routed to the MCU_CLK pin, which can be used as a clock source for the external microcontroller or other digital devices, so it is important that the clock from the high-precision oscillator has the correct frequency. Therefore, the two trimming values for the high-precision oscillator are protected by redundancy inside the OTP. Software can check the validity of the trim values and the redundancy bits by reading the OTP raw data directly from the OTP via the SPI. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 34 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Note: The trimming values for both oscillators should also be stored by the user’s external microcontroller so that the user’s software is able to check the validity of the trimming values. On detection of errors inside the OTP, the user’s software can write the correct values via SPI. 3.3.2 Trimming the Low-Power Oscillator Because the clock from the low-power oscillator is less accurate than the clock from the high-precision oscillator, a trimming circuit is implemented that trims the low-power oscillator using the divided clock divClk. There are two options for trimming the low-power oscillator. One option is to allow the hardware to update the trim value for the low-power oscillator automatically so that no user interference is necessary. For this, the user only needs to set the lpOscTrimEna and lpOscTrimUpd bits in register lpOscTrim to 1 as well as setting the lpOscTrimCfg field as needed (see Table 3.4). The latter configuration value defines how many low-power clock periods are used for frequency calculation. While the trimming circuit is faster when fewer periods are used, the result of the frequency calculation is more accurate when more periods are used. In the first part of the trimming loop, the circuit determines the frequency of the low-power oscillator. When the measured frequency is too low, the hardware increments the trim value by 1; if it is too high, the hardware decrements the trim value by 1. Otherwise, the trim value remains unchanged. After changing the trim value, the hardware measures the (new) frequency. This algorithm is only stopped when the user’s software clears the lpOscTrimEna bit (trimming logic stops after a final update) or when any low-power state is entered. The second option is to use the trim circuit only to measure the frequency but to update the trim value via the user’s software. This can be preferable when the target frequency is not equal to 125kHz. For this, the user only needs to set the lpOscTrimEna bit to 1 and set the lpOscTrimUpd bit to 0 as well as setting the lpOscTrimCfg field as needed. Next, the user must clear the lpOscTrimEna bit without changing the other values in the register and must wait until the hardware has finished to calculate the frequency (wait until SSW[6] is 0). By reading the lpOscTrimCnt register, the user can calculate the actual frequency of the low-power oscillator using the following formula: fLP fHP 2 lpOscTrimC fg 2 lpOscTrimcnt 1 fHP 4 MHz (1) After determining the actual frequency, the user can change the trim value for the low-power oscillator lpOscTrimVal as required (see Table 3.3) and re-enable the trimming circuit to check the new frequency. Note: The trimming circuit can be kept active when going to any low-power state. The PMU interrupts the trimming circuit on transition to the low-power state and restarts it after wakeup. This is needed as divClk is stopped in any low-power state. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 35 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.3.3 Clock Trimming and Configuration Registers 3.3.3.1 Register “irefOsc” – Trim Values for the High-Precision Oscillator Register irefOsc Table 3.2 Name Address irefTcOscTrim Bits Default Access [4:0] 10000BIN RW Trim value to minimize the temperature coefficient of the high-precision oscillator. Note: This value is automatically updated by the OTP controller after an SBC reset. Unused; always write as 0. Trim value for the high-precision oscillator. The frequency of the high-precision oscillator increases (decreases) when this value is incremented (decremented). C1HEX Unused irefOscTrim[0] irefOscTrim[8:1] C2HEX [6:5] [7] [7:0] 00BIN 0BIN 40HEX Description RO RW RW Note: This value is automatically updated by the OTP controller after an SBC reset. 3.3.3.2 Register “irefLpOsc” – Trim Value for the Low-Power Oscillator Table 3.3 Register irefLpOsc Name Address lpOscTrimVal Bits Default [6:0] 1010010BIN Access RW 7AHEX Unused Data Sheet July 10, 2014 [7] 0BIN RO Description Trim value for the low-power oscillator. The frequency of the low-power oscillator increases (decreases) when this value is incremented (decremented). Note: This value is automatically updated by the OTP controller after SBC reset. Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 36 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.3.3.3 Register “lpOscTrim” – Configuration Register for the Low-Power Oscillator Trimming Circuit Table 3.4 Register lpOscTrim Name Address lpOscTrimEna lpOscTrimUpd Bits Default Access [0] 0BIN RW [1] 0BIN RW 7BHEX lpOscTrimCfg [3:2] Unused 3.3.3.4 [7:3] 00000BIN RW RO If set to 1, enables the low-power oscillator trimming circuit. Note: When the user disables the trimming feature, the trimming logic continues its operation until it has finished the current calculation and then stops. The user can check that the trimming circuit has stopped by evaluating SSW[6], which is 0 when the trimming circuit is inactive. Update bit for the low-power oscillator trimming circuit. When set to 1, the trimming circuit is allowed to update lpOscTrimVal in register irefLpOsc. When set to 0, no hardware update is performed. Note: Do not change while trimming circuit is active. This value selects the number of clock periods of the low-power oscillator to be used to determine the frequency. 0 4 clock periods 1 8 clock periods 2 16 clock periods 3 32 clock periods Note: Do not change while trimming circuit is active. Unused; always write as 0. Register “lpOscTrimCnt” – Result Counter of the Low-Power Oscillator Trimming Circuit Table 3.5 Register lpOscTrimCnt Name Address lpOscTrimCnt[7:0] lpOscTrimCnt[10:8] Unused Data Sheet July 10, 2014 01BIN Description 78HEX 79HEX Bits Default Access [7:0] 00HEX RO [2:0] [7:3] 000BIN 00000BIN RO RO Description Result counter of the low-power oscillator trimming circuit. This value will only be read when the trimming circuit is inactive (SSW[6] == 0). Unused; always write as 0 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 37 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.3.4 Resets The main reset source is the integrated power-on-reset circuit, which resets the complete digital core of the SBC when VDDE drops below 3.0V (typical). There are three other reset sources that reset the complete digital core of the SBC except the watchdog timer and its configuration registers. These additional reset sources are Watchdog reset: This reset occurs when the active watchdog timer expires without being handled by the user’s software. Software reset: This reset can be generated by the user by writing the value A9HEX to register swRst. PMU error reset: This reset occurs if the power management unit (PMU) goes into an invalid state (e.g., due to cosmic radiation). If any of these four resets occurs, the power-on procedure is executed, which powers up the required analog blocks and starts the download procedure for the OTP. This download procedure transfers the OTP contents into the appropriate registers if the OTP content is valid. The MCU_RSTN pin is driven low, which can be used to reset the connected external microcontroller. The microcontroller reset is released after the power-up procedure has finished. The MCU_RSTN pin is also driven low when the system goes to OFF or ULP State because the power supplies to the microcontroller (VDDP, VDDC) are disabled in these power-down states. In this case, the MCU_RSTN low state is released after a wake-up event has occurred and the power supplies to the external microcontroller have stabilized. Another possible reset source for the external microcontroller is VddpReset, which is also generated by the power-on-reset circuit when VDDE drops below 4.05V (typical). In this case, it cannot be guaranteed that VDDP, which is needed for correct operation of the external microcontroller, is still valid if VDDP is trimmed to the higher level of 3.3V (see section 3.12.5). The digital core of the SBC observes the input from the power-on-reset block and generates the MCU_RSTN signal only when all of the following conditions are true: VDDP is trimmed to 3.3V (bit vddpTrim of register pwrTrim is set to 1). The ZSSC1750/51 system is in the Full-Power State (FP). VDDP reset is not disabled (bit disVddpRst of register funcDis is set to 0; see Table 3.8). 3.3.4.1 The Reset Status The external microcontroller can easily check the reason for being reset by a single-byte transfer to the SBC (SPI address byte only) and evaluating SSW[10:8], which contains the reason for the last reset (reset status). This value can be evaluated by the user’s software for different actions after reset: Reset status 0: In this case, the reset was generated by the power-on-reset cell. The SBC was reset, and a MCU_RSTN signal was generated to reset the external microcontroller. Reset status 1: The watchdog timer was not handled and has expired (see section 3.4). The SBC logic (except the watchdog timer and its configuration registers) was reset and a MCU_RSTN signal was generated to reset the external microcontroller Reset status 2: Only a MCU_RSTN signal was generated to reset the external microcontroller due to a wakeup from the ULP or OFF State. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 38 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Reset status 3: The user’s software has forced a reset. The SBC logic (except the watchdog timer and its configuration registers) was reset and a MCU_RSTN signal was generated to reset the external microcontroller. Reset status 4: VDDP has dropped below 3.3V, and the external microcontroller was active. Only a MCU_RSTN signal was generated to reset the external microcontroller. Reset status 5: The PMU is in an illegal state. The SBC logic was reset (except the watchdog timer and its configuration registers) and a MCU_RSTN signal was generated to reset the external microcontroller. 3.3.4.2 The Low-Voltage Flag The low-voltage flag is part of the analog block. The low-voltage flag is at low-level state after power-on-reset. It can be set by the user’s software by writing the value ‘1’ to bit lvfSet in register cmdExe. It is cleared by the power-on-reset cell when VDDE drops below 1.9V (typical). When VDDE drops below this threshold, it cannot be guaranteed that the VDDL voltage is high enough to provide a reliable SBC digital supply. The low-voltage flag is mapped to SPI SSW[11] where the user’s software can read its value. 3.3.4.3 Register “swRst” – Software Reset Register swRst Table 3.6 Name Address Bits Default Access swRst 80HEX [7:0] 00HEX WO 3.3.4.4 Register “cmdExe” – Triggering Command Execution by Software Table 3.7 Register cmdExe Name Address wdogClr otpDownload lvfSet Unused Data Sheet July 10, 2014 Description Writing A9HEX to this register forces a software reset, which generates a MCU_RSTN signal to reset the external microcontroller as well as the SBC digital core except the watchdog timer and its configuration registers. Always reads as 0. 68HEX Bits Default Access [0] 0BIN RW [1] 1BIN WO [2] 0BIN WO [7:3] 00000BIN RO Description Writing 1 to this bit clears the watchdog timer. This bit is cleared by hardware after the watchdog is cleared. As long as the clear procedure is active, any further writes to this bit are rejected. Strobe register; write 1 to start the download procedure from the OTP; always reads as 0. Strobe register; write 1 to set the low-voltage flag; always reads as 0. Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 39 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.3.4.5 Register “funcDis” – Disabling VDDP Reset and STO Output Pin Table 3.8 Name Register funcDis Address disVddpRst disStoOut B9HEX Unused 3.4 Bits Default Access [0] 0BIN RW [1] 0BIN RW [7:2] 000000BIN Description When set to 1, VddpReset does not generate a MCU_RSTN signal to reset the external microcontroller. When set to 1, the output driver of the STO pin is disabled. Unused; always write as 0. RO SBC Watchdog Timer (WD_TIMER Block) The SBC contains a configurable watchdog timer (down counter) for the ZSSC1750/51 when it is running using the clock from the low-power oscillator. It is used to recover from an invalid software or hardware state. To avoid a reset of the system, the watchdog must be periodically serviced. The only part of the system that will not be reset by the watchdog reset is the watchdog itself and its configuration registers. Figure 3.2 Structure of the Watchdog Timer lpClk (125 kHz) Configurable Prescaler 1:1 1 : 125 1 : 1250 1 : 12500 wdogCnt (register file) 16-Bit Down Counter == 0? wdogPrescaleCfg (register file) & set wdIrq (IRQ ctrl) & set wdRst (RstCtrl) wdogIrqFuncEna (register file) O R By default, the watchdog timer is active starting with a counter value of FFFF HEX and a prescaler of 125. This is done to guarantee that the boot code of the external microcontroller has enough time to finish. During the initialization phase of the system, the user’s software can disable, reconfigure, and restart the watchdog. Disabling the watchdog before configuration is required as all write accesses to the register wdogPresetVal and the register wdogCfg except the bits wdogLock and wdogEna (see Table 3.12) are blocked when the watchdog is active. As it takes multiple low-power clock cycles until the enable signal is evaluated inside the watchdog clock domain, the SSW[7] bit (wdActive) must be checked to determine if write accesses are possible. To avoid any malfunction during reconfiguration, the prescaler registers are set to 0 and the counter register is set to FFFFHEX at disable. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 40 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) When the watchdog is disabled, configuration is possible. The register wdogPresetVal contains the value that will be copied into the down counter in the first enable cycle or when the watchdog timer is serviced via the wdogClr bit in register cmdExe. The field wdogPrescaleCfg in register wdogCfg configures the prescaler. The resolution and maximum timeout for the watchdog depend on the configuration as shown in Table 3.9. Table 3.9 Resolution and Maximum Timeout for Prescaler Configurations wdogPrescaleCfg Setting Prescaler Configuration Resolution Maximum Timeout 0 1:1 8µs 524 ms 1 1:125 1ms 65.5 s 2 1:1250 10ms 655.3 s 3 1:12500 100ms 6553.5 s As the maximum timeout value might still be too small for some applications, the user can use the wdogPmDis bit in register wdogCfg to select whether the watchdog timer will be halted during any power-down state (bit set to 1) or not (bit set to 0). It is also possible to use the watchdog timer (WDT) as a wake-up source. When the wdogIrqFuncEna bit in register wdogCfg is set to 1 and the down counter reaches 0, an interrupt is generated (instead of a reset that would wake up the system) and the down counter reloads the preset value and continues its operation. When the watchdog timer expires for a second time without service, the watchdog reset is generated. If the wdogIrqFuncEna bit is set to 0, the reset is already generated when the timer expires for the first time. After reconfiguration, the watchdog timer is re-enabled. To avoid further (accidental) changes to the watchdog timer configuration registers, the user can set the wdogLock bit inside the register wdogCfg to 1. If this bit is set, all write accesses are blocked. The wdogLock bit will only be cleared by a power-on reset. The WDT can also be disabled by driving the WDT_DIS pin HIGH. In this case it is halted, but still can be cleared via the wdogClr bit in register cmdExe (see Table 3.7). This functionality is useful in the external microcontroller’s in-circuit programming mode to disable a reset generated by the watchdog timer. To perform the required period servicing of the watchdog timer, the user must write the value 1 to the wdogClr bit in register cmdExe. To avoid any malfunction if the watchdog is serviced too often, any consecutive write accesses to the wdogClr bit are blocked until the first clear process has finished. Important: The preset value programmed to the wdogPresetVal register must never be 0HEX as this would immediately cause a reset forcing the system into a dead lock. It is strongly recommended that the user’s software checks the programmed reload value before re-enabling the watchdog. Important: The preset value must not be too small. The user must take into account critical system timings including power-up times and flash programming/erasing times. Note: The reconfiguration of the registers wdogPresetVal and wdogCfg, including bits wdogEna and wdogLock, can be done in a single SPI burst write access. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 41 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.4.1 Watchdog Registers 3.4.1.1 Register “wdogPresetVal” – Preset Value for the Watchdog Timer Table 3.10 Register wdogPresetVal Important: The preset value programmed to this register must never be 0HEX (see section 3.4 above). Name Address wdogPresetVal[7:0] 72HEX Bits [7:0] Default FFHEX Access RW Description Lower byte of the preset value of the watchdog timer. This value is loaded into the lower byte of the watchdog counter when the watchdog is enabled or when the watchdog is cleared. Note: This bit can only be written when the watchdog is not locked (wdogLock == 0) and when the watchdog is inactive (SSW[7] == 0). wdogPresetVal[15:8] 73HEX [7:0] FFHEX RW Upper byte of the preset value of the watchdog timer. This value is loaded into the upper byte of the watchdog counter when the watchdog is enabled or when the watchdog is cleared. Note: This bit can only be written when the watchdog is not locked (wdogLock == 0) and when the watchdog is inactive (SSW[7] == 0). 3.4.1.2 Register “wdogCnt” – Current Value of Watchdog Timer Table 3.11 Register wdogCnt Name wdogCnt[7:0] wdogCnt[15:8] Data Sheet July 10, 2014 Address Bits Default Access 70HEX 71HEX [7:0] [7:0] 00HEX 00HEX RO RO Description Lower byte of current watchdog timer value Upper byte of current watchdog timer value © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 42 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.4.1.3 Register “wdogCfg” – Watchdog Timer Configuration Register Table 3.12 Register wdogCfg Name Address Bits Default Access [0] 1BIN RW wdogEna Description Global enable bit for the watchdog timer. wdogPmDis [1] 0BIN RW wdogIrqFuncEna [2] 0BIN Note: This bit can only be written when the watchdog is not locked (wdogLock == 0). RW RW Note: This bit can only be written when the watchdog is not locked (wdogLock == 0) and when the watchdog is inactive (SSW[7] == 0) Prescaler configuration: 0 No prescaler active 1 Prescaler of 125 is active 2 Prescaler of 1250 is active 3 Prescaler of 12500 is active wdogPrescaleCfg 01BIN When this bit is set to 1, PMU stops the watchdog during any power-down state. When this bit is set to 1, the watchdog reloads the preset value when expiring for the first time and generates an interrupt instead of a reset. A reset will always be generated when the watchdog timer expires for the second time. 74HEX [4:3] Note: This bit can only be written when the watchdog is not locked (wdogLock == 0). Note: This bit can only be written when the watchdog is not locked (wdogLock == 0) and when the watchdog is inactive (SSW[7] == 0) Unused [6:5] 00BIN RO wdogLock 7 Data Sheet July 10, 2014 0BIN RWS Unused; always write as 0. When this bit is set to 1, all write accesses to the other bits of this register as well as to the wdogPresetVal registers are ignored. This bit can only be written to 1 and is only cleared by a poweron reset. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 43 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.5 SBC Sleep Timer (GP_TIMER Block) The integrated sleep timer (up counter) in the GP_TIMER (general-purpose timer) block is only active when the system is in any low-power state and it is running with the 125kHz clock from the low-power oscillator. The sleep timer consists of three blocks: A fixed prescaler that divides the incoming 125kHz clock from the low-power oscillator by 12500 to get a timer resolution of 10 Hz. A 16-bit counter that generates an interrupt (signal: stlrq) when the timer reaches the programmed compare value in the sleepTCmp register (see Table 3.14). A 12-bit counter that triggers the PMU (with signal stAdcTrigger) when the timer reaches the programmed compare value in the sleepTAdcCmp register (see Table 3.13) to power-up the ADC blocks and to perform measurements if one of the discrete measurement scenarios are configured. Figure 3.3 Structure of the Sleep Timer sleepTCmp (register file) 16-Bit Counter lpClk (125 kHz) Prescaler 1 : 12500 == ? stIrq (IRQ ctrl) sleepTCurCnt (register file) cntClk (10 Hz) 12-Bit Counter == ? stAdcTrigger (PMU) sleepTAdcCmp (register file) When the system goes from the Full-Power (FP) State to any power-down state on request by the user, the prescaler and both counters are cleared and the 16-bit counter is enabled. Every 100ms, triggered by the prescaler, the 16-bit counter is incremented until it reaches the programmed compare value sleepTCmp. When the compare value is reached, the timer stops and the interrupt controller is triggered to set the corresponding status flag (see section 3.6.1.1). The sleep timer is also stopped when the system returns to the FP State. The user can determine the sleep duration by reading the register sleepTCurCnt, which returns the value of the 16-bit counter (see Table 3.15). Note: Although the timer stops and the interrupt status bit is set when the compare value is reached, the system remains in the power-down state if the corresponding interrupt is not enabled to drive the interrupt line IRQN (bit 1 in the irqEna register; see Table 3.17). Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 44 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Equation (2) can be used to determine the correct sleep time to be programmed. The sleep timer expires after 100ms for a compare value of 0, after 200ms for a compare value of 1, and so on. SleepTime 100ms sleepTCmp 1 (2) The 12-bit counter that triggers the PMU is only enabled during any power-down state when any discrete measurement scenario is configured. In this case, the counter is incremented each 100ms triggered by the prescaler. When the counter reaches the programmed compare value sleepTAdcCmp, a strobe for the PMU is generated and the 12-bit counter is reset to 0. Then it continues its operation. This counter is only stopped when the system returns to the FP State, but it continues to operate when the sleep timer has expired if it was not enabled to wake up the system. Equation (3) can be used to determine the correct ADC trigger time to be programmed. The ADC trigger timer expires after 100ms for a compare value of 0, after 200ms for a compare value of 1, and so on. In general ADC TriggerTime 100ms sleepTAdcCmp 1 (3) Important: When both the sleep timer for wake-up and the ADC trigger timer for discrete measurements are used, special care must be taken when programming the compare values because when the sleep timer expires, the wake-up condition has higher priority over an active ADC measurement or an ADC trigger strobe. 3.5.1 Sleep Timer Registers 3.5.1.1 Register “sleepTAdcCmp” – Compare Value for ADC Trigger Timer Table 3.13 Register sleepTAdcCmp Name Addr Bits Default Access sleepTAdcCmp[7:0] 60HEX [7:0] 00HEX RW sleepTAdcCmp[15:8] 61HEX [7:0] 00HEX RW Data Sheet July 10, 2014 Description Lower byte of compare value for the ADC trigger timer; the ADC trigger timer is only active if the system is in LP or ULP State and any discrete measurement scenario is configured generating periodic strobes for the PMU. ADC trigger time = 100 ms (sleepTAdcCmp + 1) Upper byte of compare value for ADC trigger timer; ADC trigger timer is only active when the system is in LP or ULP State and any discrete measurement scenario is configured generating periodic strobes for the PMU. ADC trigger time = 100 ms (sleepTAdcCmp + 1) © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 45 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.5.1.2 Register “sleepTCmp” – Compare Value for Sleep Timer Table 3.14 Register sleepTCmp Name Addr Bits Default Access sleepTCmp[7:0] 62HEX [7:0] 00HEX RW sleepTCmp[15:8] 63HEX [7:0] 00HEX RW 3.5.1.3 Description Lower byte of compare value for sleep timer; sleep timer is only active if the system is in LP or ULP State. Sleep time = 100 ms (sleepTCmp + 1) Upper byte of compare value for sleep timer; sleep timer is only active when the system is in LP or ULP State. Sleep time = 100 ms (sleepTCmp + 1) Register “sleepTCurCnt” – Current Value of Sleep Timer Table 3.15 Register sleepTCurCnt Name sleepTCurCnt[7:0] sleepTCurCnt[15:8] Addr Bits Default Access 20HEX [7:0] 00HEX RO 21HEX [7:0] 00HEX RO Description Lower byte of the current sleep timer value. Since the timer is stopped in FP State, the duration of the last power-down state can be determined: Sleep time = 100ms (sleepTCurCnt + 1) Note: Value is only valid when SSW[1] (sleep timer valid stValid) is set. Upper byte of the current sleep timer value. Since the timer is stopped in FP State, the duration of the last power-down state can be determined: Sleep time = 100ms (sleepTCurCnt + 1) Note: Value is only valid when SSW[1] (stValid) is set. 3.6 SBC Interrupt Controller (IRQ_CTRL Block) There are 16 different interrupt sources in the SBC system, each having a dedicated interrupt status bit in the irqStat register (see Table 3.16) and a dedicated interrupt enable bit in the irqEna register (see Table 3.17). The interrupt controller captures each interrupt source in the interrupt status register independently of the interrupt enable settings. The interrupt controller combines all enabled interrupt status bits into the low-active interrupt signal that is used to drive the interrupt pin IRQN of the SBC and to wake up the system by the PMU. This means that interrupt status bits, which can always be set even when disabled, can only generate a wake-up event and drive the interrupt pin IRQN when they are enabled. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 46 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.4 Generation of Interrupt and Wake-up irqStat[0] irqEna[0] & . . . IRQN O R irqStat[15] wake-up (to PMU) irqEna[15] & The user can determine the interrupt reason by reading the interrupt status register irqStat. The interrupt status register is cleared on each read access. Therefore the user’s software must ensure that it stores the read interrupt status value if needed to avoid loss of information. 3.6.1.1 Interrupt Sources The bit mapping is the same for the interrupt enable register irqEna (see Table 3.17) and the interrupt status register irqStat (see Table 3.16): Bit 0: Watchdog Timer Interrupt; status is set by the watchdog timer when the interrupt functionality of the watchdog timer is enabled and the watchdog timer expires for the first time. Bit 1: Sleep Timer Interrupt; status is set by the sleep timer when the sleep timer reaches the programmed compare value. Bit 2: LIN TXD Timeout Interrupt (for ZSSC1750 only); status is set by the LIN support logic when the TXD input from the external microcontroller is low for more than 10.24ms. Bit 3: LIN Short Interrupt (for ZSSC1750 only); status is set by the LIN support logic when a short is detected in the LIN PHY. Bit 4: LIN Wakeup Interrupt (for ZSSC1750 only); status is set by the LIN support logic when a wake-up frame is detected on the LIN bus. Bit 5: Current Conversion Result Ready Interrupt; status is set by the ADC unit when a single current measurement (register adcCrcl == 0) or multiple current measurements defined by adcCrcl (register adcCrcl 0) have been completed and the result is available. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 47 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Bit 6: Voltage Conversion Result Ready Interrupt; status is set by the ADC unit when a single voltage measurement (register adcVrcl == 0) or multiple voltage measurements defined by the adcVrcl (register adcVrcl 0) have been completed and the result is available. Bit 7: Temperature Conversion Result Ready Interrupt; status is set by the ADC unit when a single temperature measurement has been completed and the result is available. Bit 8: Current Comparator Interrupt; status is set by the ADC unit when the Current Threshold Counter Mode is enabled (register adcAcmp[2:1] ≠ 00) and the absolute value of multiple current measurements (defined by register adcCtcl) exceeds the programmed current threshold (register adcCrth). Note: If the threshold counter mode is enabled but adcCtcl is 0, this bit is always set independently of the threshold. Bit 9: Voltage Comparator Interrupt; status is set by the ADC unit if the VThWuEna bit (adcAcmp[8]) is set to 1 and a single measured voltage or the accumulated voltage measurements (depends on configured mode) drop below the programmed (register adcVTh) voltage threshold. Bit 10: Temperature Threshold Interrupt; status is set by the ADC unit when the TWuEna bit (adcAcmp[10]) is set to 1 and a temperature measurement is outside the specified temperature interval defined by registers adcTmin and adcTmax. Bit 11: Current Accumulator Threshold Interrupt; status is set by the ADC unit when the CAccuThEna bit (adcAcmp[3]) is set to 1 and the accumulated current values rise above the programmed threshold value (register adcCaccTh) for a positive threshold value or fall below the programmed threshold value for the negative threshold value. Bit 12: Current Overflow Interrupt; status is set by the ADC unit when the COvrEna bit (adcAcmp[4]) is set to 1 and the compensated value of a current measurement is outside of the representable range. Bit 13: Voltage/Temperature Overflow Interrupt; status is set by the ADC unit when the VTOvrEna bit (adcAcmp[5]) is set to 1 and the compensated value of a voltage or temperature measurement is outside of the representable range. Bit 14: Current Over-Range Interrupt; status is set by the ADC unit when the COvrEna bit (adcAcmp[4]) is set to 1 and the input from the current ADC is overdriven. Bit 15: Voltage/Temperature Over-Range Interrupt; status is set by the ADC unit when the VTOvrEna bit (adcAcmp[5]) is set to 1 and the input from the voltage/temperature ADC is overdriven. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 48 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.6.1.2 Register “irqStat” – Interrupt Status Register Table 3.16 Register irqStat Name Address Bits Default Access irqStat[7:0] 00HEX [7:0] 00HEX RC irqStat[15:8] 01HEX [7:0] 00HEX RC Description Lower byte of the interrupt status register as defined in section 3.6.1.1; each bit is set by hardware and cleared on read access. Upper byte of interrupt status register as defined in section 3.6.1.1; each bit is set by hardware and cleared on read access. Note: To avoid loss of information, the hardware set condition has a higher priority than the read clear condition. 3.6.1.3 Register “irqEna” – Interrupt Enable Register Table 3.17 Register irqEna Name Address Bits Default Access irqEna[7:0] 54HEX [7:0] 00HEX RW irqEna[15:8] 55HEX [7:0] 00HEX RW Description Lower byte of the interrupt enable register as defined in section 3.6.1.1; only enabled interrupts can drive the interrupt line and wake up the system; the bit mapping is the same as for the interrupt status register. Upper byte of the interrupt enable register as defined in section 3.6.1.1; only enabled interrupts can drive the interrupt line and wake up the system; the bit mapping is the same as for the interrupt status register. Note: The interrupt enable bit for the LIN wake-up interrupt (irqEna[4]) is also used as the enable for the LIN wake-up (for ZSSC1750 only) frame detector within the PMU. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 49 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.7 SBC Power Management Unit (SBC_PMU Block) The power management unit (PMU) controls placing the SBC into the selected power down state, controlling the power down signals for the different analog blocks, and controlling the clocks for the digital logic. It also controls the other digital modules during the power-down state. The system provides four different power states: FP (Full-Power State) In this state, all blocks are powered except the ADCs if the user’s software has not enabled them. All internal clocks are active (divClk and muxClk are 4MHz) and the external microcontroller is also powered and clocked through pins VDDP, VDDC, and MCU_CLK. When powered and enabled by software, the ADC clocks are generated from the clock from the high-precision oscillator. LP (Low-Power State) In this state, the high-precision oscillator and the LIN transmitter (ZSSC1750 only) are powered down. The clock for the external microcontroller (MCU_CLK) is stopped, but the microcontroller remains powered through VDDP and/or VDDC. Depending on the selected measurement scenario, the ADCs are also powered down during times of inactivity. Otherwise the ADC clocks are generated from the low-power oscillator. ULP (Ultra-Low-Power State) In this state, the high-precision oscillator and the LIN transmitter (ZSSC1750 only) are powered down. The optional external microcontroller clock MCU_CLK is stopped and the supply voltages for the external microcontroller (VDDP, VDDC) are powered down. Depending on the selected measurement scenario, the ADCs are also powered down during times of inactivity. Otherwise, the ADC clocks are generated from the clock from the low-power oscillator. OFF (Off State) In this state, all analog blocks except the digital power supply for the SBC and the RX part of the LIN PHY (ZSSC1750 only) are powered down. The external microcontroller clock MCU_CLK is stopped, and the supply voltages for the external microcontroller (VDDP, VDDC) are powered down. For the ZSSC1750/51 to enter any of the power-down states (LP, ULP, or OFF), the user’s software must first set the pdState field of register pwrCfgLp to select the state (see Table 3.19) and enable the interrupts needed as the wakeup source before writing A9HEX to register gotoPd (see Table 3.20). Immediately after A9HEX is written to the gotoPd register, the CSN line must be driven high. Although for all other register accesses, the CSN line can be kept low and the next SPI transfer can follow immediately, it is mandatory to drive CSN high for the power-down command. Otherwise, the PMU remains in the FP State. Important: If no interrupt is enabled, the system can only be awakened by power-on-reset! Note: The CSN line must be driven high to go to power-down after writing the value A9HEX to register gotoPd. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 50 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) The following tasks are always performed on transition to any power-down state by the PMU: Both ADCs are stopped. Any active measurement is interrupted. ADC control is transferred to the PMU. Those configuration values that can be configured independently for the Full-Power State and power-down states are switched to the power-down settings. The sleep timer is cleared and enabled. The clock on the MCU_CLK pin is stopped. The high-precision oscillator is powered down. The TX part of the LIN PHY is powered down (ZSSC1750 only). The source for the muxClk changes from divClk to lpClk. If any of the enabled interrupts occurs and the interrupt pin IRQN is driven low, the system wakes up immediately; any ADC measurement that is active during the power-down state is stopped. All mandatory blocks are powered up, and the system waits for stabilization before re-enabling the clock output MCU_CLK for the external microcontroller. If any of the enabled interrupts is already active on reception of the power-down command or becomes active on transition to the requested power-down state, the system rejects the power-down command or re-enables those blocks that are already powered down. Depending on the time when the power-down procedure was interrupted, it is possible that the sleep timer was not cleared. In this case, the sleep timer valid flag is cleared, signaling that the sleep timer value in register sleepTCurCnt is not valid. This flag is mapped to SSW[1]. 3.7.1 FP State After the initial power-on reset when the OTP contents are downloaded into the registers and all blocks have stabilized, the system enters the FP State. In this state, all voltage regulators, both oscillators and the LIN PHY (ZSSC1750 only) are powered but the ADCs are still powered down. Important: Both ADCs are powered down after power-on reset. To be able to use the ADCs, the user must first power up the required ADCs by programming register pwrCfgFp, bits pwrAdcI and/or pwrAdcV (see Table 3.18). The first bit enables the current ADC and the second bit enables the voltage/temperature ADC. In this register are three other bits that can be set by the user, but they should be handled with care as the system consumes less power when any of these bits is set but the accuracy of the measurement results is reduced: lpEnaFp if set to 1, the bias current for analog blocks is reduced to 10% ulpEnaFp if set to 1, the bias current for analog blocks is reduced to 5% pdRefbufOcFp if set to 1, the offset cancellation circuit inside the reference buffer is powered down Note: If both lpEnaFp and ulpEnaFP are set to 1, the bias current for analog blocks is reduced to 15%. Important: These settings are only used in FP State. For configuration for the power-down states, the pwrCfgLp register must be used. The settings in register pwrCfgFp are preserved when entering any power-down state by executing the powerdown command. The PMU overrides these settings or switches to the settings made in register pwrCfgLp on transition to the power-down state. When the system wakes up and returns to the FP State, the PMU restores the settings as configured in pwrCfgFp regardless of whether any ADC was powered in power-down state or not. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 51 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.7.2 LP and ULP States The LP and ULP power-down states are used to save power while doing measurements with lower accuracy. In both states, the TX part of the LIN PHY and the high-precision oscillator are powered down and the external microcontroller clock is stopped. The internal clock muxClk is driven by the low-power oscillator with a frequency of 125kHz while the internal clock divClk is stopped. In ULP State, the two voltage regulators VDDP (IO voltage for SBC and external microcontroller) and VDDC (optional core voltage for external microcontroller) are powered down. In this case, the SLEEPN pin is driven low to indicate this state. The state of the ADCs and the other analog blocks needed for measurements depends on the configured measurement setup for the power-down state (see following subsections). The blocks are powered when they are needed for measurement and powered down when they are not needed for measurement. This is controlled by the PMU as well as the control signals (start, stop, mode) for the digital ADC unit. The main configuration register for the power-down behavior is register pwrCfgLp (see Table 3.19). The field pdState is used to select the power-down state to be entered on reception of the power-down command, and the field pdMeas is used to define the measurement setup to be used during the power-down state. There are three other bits to configure the power-down behavior: lpEnaLp if set to 1, the bias current for analog blocks is reduced to 10% ulpEnaLp if set to 1, the bias current for analog blocks is reduced to 5% pwrRefbufOcLp if set to 1, the offset cancellation circuit in the reference buffer is powered up Note: If both lpEnaLp and ulpEnaLp are set to 1, the bias current for analog blocks is reduced to 15%. For the corresponding bits for the FP State, lpEnaFp and ulpEnaFp in register pwrCfgFp (see Table 3.18), the meaning is the same, but the default settings are different. While there is no bias current reduction during FP State (default setting for both bits is 0), the default bias current for the LP and ULP States is reduced to 10%. The meaning of the control bit for the offset cancellation differs: the FP State control bit is a power-down signal; the LP/ULP State control bit is a power-up bit. While the offset cancellation is enabled by default during the FP State (pdRefbufOcFp == 0), the offset cancellation is disabled by default during the LP or ULP State (pdRefbufOcLp == 0). Both bits are configurable by the user. On transition to the LP or ULP State, the sleep timer and the ADC trigger timer are cleared. While the sleep timer is always enabled during power-down states, the ADC trigger timer is only enabled when performing discrete measurements. If the sleep timer interrupt is enabled, the system wakes up when the sleep timer expires. If the sleep timer interrupt is not enabled, the sleep timer stops when it expires, but the ADC trigger timer, if enabled due to the measurement configuration, continues its operation. For wake-up, other interrupts must be enabled; e.g., LIN wakeup (for ZSSC1750 only). Note: The sleep timer is always active during the LP and ULP States. Note: When reading the sleep timer value after wake-up by another enabled interrupt, the sleep timer is only valid when it has not reached its compare value although the valid flag says valid. Whether the sleep timer is valid can be determined by the sleep timer status bit. When the system wakes up and returns to FP State, the sleep timer is stopped. The user’s software can read the sleep timer value to determine the duration of the power-down state. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 52 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.7.2.1 Performing No Measurements during LP/ULP State When the LP or ULP State has been entered, all analog blocks related to ADCs are powered down. If the system goes to power down without performing any measurements, only three different wake-up sources are possible: the watchdog timer interrupt, the sleep timer interrupt, and the LIN wakeup interrupt (for ZSSC1750 only). Important: At least one of these interrupts must be enabled, as otherwise the system can only wake up via power-on reset. If no interrupt is enabled, the system cannot wake up. To go to LP or ULP State without performing measurements, the following tasks must be done: Enable at least one of the following interrupts: Set irqEna[0] to 1 to enable the watchdog interrupt to wake up the system. Set irqEna[1] to 1 to enable the sleep timer to wake up the system. Set irqEna[4] to 1 to enable the LIN wake-up detector and to enable the system to wake up due to a LIN wakeup frame (for ZSSC1750 only). Set up the sleep timer compare value (register sleepTCmp) if needed. Configure the pwrCfgLp register as follows: Set pdState to 0 or 1 to configure the LP State or to 2 to configure the ULP State. Set pdMeas to 0 to configure the system to perform no measurements. Set lpEnaLp, ulpEnaLp and pwrRefbufOcLp as needed. Write A9HEX to register gotoPd and then drive the CSN line high. When an enabled interrupt occurs, the system wakes up and the settings from register pwrCfgFp are restored. When all blocks have stabilized, the external microcontroller clock MCU_CLK is re-enabled, and if coming out of the ULP State, the microcontroller reset MCU_RST is released. Figure 3.5 LP/ULP State without any Measurements Note: the sleep timer is used as the wake-up source in this example, but it could also be the watchdog timer interrupt or the LIN wakeup interrupt. I gotoPd Command Wakeup Due to Sleep Timer Interrupt FP Data Sheet July 10, 2014 LP / ULP FP © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. t 53 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.7.2.2 Performing Discrete Measurements of Current during LP/ULP State The system can be configured to periodically enable the current ADC and to measure the current during the LP or ULP State. The current ADC can be configured to perform several current measurements during each measurement phase (green boxes in Figure 3.6). Upon entering the LP/ULP State and between the measurements, the current ADC is powered down. The voltage/temperature ADC is powered down for the entire power-down period. The PMU powers up the current ADC when triggered by the ADC trigger timer. Possible wake-up sources during this scenario are the watchdog timer interrupt, the sleep timer interrupt, the LIN wakeup interrupt (for ZSSC1750 only), or any of the ADC interrupts related to current. Important: When no interrupt is enabled, the system cannot wake up. To go to LP or ULP State and perform discrete current measurements, the following tasks must be done: Enable at least one of the following interrupts: Set irqEna[0] to 1 to enable the watchdog interrupt to wake up the system. Set irqEna[1] to 1 to enable the sleep timer to wake up the system. Set irqEna[4] to 1 to enable the LIN wake-up detector and to enable the system to wake up due to a LIN wakeup frame (for ZSSC1750 only). Enable any ADC interrupt related to current (see section 3.6.1.1). Set up the sleep timer compare value (register sleepTCmp) if needed. Set up the ADC trigger timer compare value (register sleepTAdcCmp) as needed. Configure the pwrCfgLp register as follows: Set pdState to 0 or 1 to configure LP State or to 2 to configure ULP State. Set pdMeas to 1 to configure the system to perform discrete current measurements. Set lpEnaLp, ulpEnaLp and pwrRefbufOcLp as needed. Write A9HEX to register gotoPd and then drive the CSN line high. When an enabled interrupt occurs, the system wakes up and the settings from register pwrCfgFp are restored. When all blocks have stabilized, the external microcontroller clock is re-enabled and, if coming out of ULP State, the microcontroller reset is released. Important: If any measurement is active while an enabled interrupt occurs (e.g., the sleep timer expires), the measurement is interrupted and the system returns to FP State. In the example shown in Figure 3.6, the first wakeup is by the ADC and the second wake-up is by the sleep timer; however, the wakeups could be other combinations of the watchdog timer interrupt, sleep timer interrupt, and/or LIN wakeup interrupt (ZSSC1750 only). Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 54 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.6 LP/ULP State Performing Only Current Measurements I gotoPd Command gotoPd Command ADC Trigger Time Current Only Measurements FP 3.7.2.3 Wakeup Due to Sleep Timer Interrupt Current Wakeup LP / ULP FP LP / ULP FP t Performing Discrete Measurements of Current, Voltage, and Internal Temperature during LP/ULP State During the LP or ULP State, the system can be configured to periodically enable both ADCs and measure current, voltage, and internal or external temperature (see section 3.7.2.4 for external temperature). The sequence can be selected in the pdMeas bit field [4:2] in register pwrCfgLp, which also selects whether internal or external temperature is measured. The period between each measurement is determined by the ADC trigger timer (sleepTAdcCmp). The current ADC can be configured to perform multiple current measurements during each measurement window (green and orange boxes in Figure 3.7 to Figure 3.9) while the voltage/temperature ADC can be configured to perform multiple voltage or internal temperature measurements (orange boxes in Figure 3.7 to Figure 3.9). After performing the configured number of voltage measurements, the PMU changes the configuration for the voltage/temperature ADC and performs a single measurement of the internal temperature. Voltage and temperature are not measured in each sample period if the ADCs are configured for measuring only current in a specified number of initial loops. The user can configure register discCvtCnt (see Table 3.21) so that in the first discCvtCnt samples, only current is measured before voltage and temperature are measured in the next sample. Upon entering the LP/ULP State and between the measurements, both ADCs are powered down. The PMU powers up the current ADC when triggered by the ADC trigger timer. The voltage/temperature ADC is only powered up after discCvtCnt current-only measurements have been performed. Possible wake-up sources in this setup are all interrupts except LIN short and LIN TXD timeout interrupts (ZSSC1750 only). Important: When no interrupt is enabled, the system cannot wake up. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 55 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) To go to the LP or ULP State and perform measurements of discrete current, voltage, and internal temperature, the following tasks must be done: Enable at least one of the following interrupts: Set irqEna[0] to 1 to enable the watchdog interrupt to wake up the system. Set irqEna[1] to 1 to enable the sleep timer to wake up the system. Set irqEna[4] to 1 to enable LIN wake-up detector and to enable the system to wake up due to a LIN wakeup frame (for ZSSC1750). Enable any ADC interrupt (see section 3.6.1.1). Configure the sleep timer compare value (register sleepTCmp) if needed. Set up the ADC trigger timer compare value (register sleepTAdcCmp) as needed. Configure the pwrCfgLp register as follows: Set pdState to 0 or 1 to configure the LP State or to 2 to configure the ULP State. Set pdMeas to 2 to configure the system to perform discrete current, voltage, and internal temperature measurements. Set lpEnaLp, ulpEnaLp and pwrRefbufOcLp as needed. Set discCvtCnt as needed. This register defines the number of current-only measurement loops before performing measurements of all three parameters. Write A9HEX to register gotoPd and then drive the CSN line high. When an enabled interrupt occurs, the system wakes up and the settings from register pwrCfgFp are restored. When all blocks have stabilized, the external microcontroller clock is re-enabled and if coming out of the ULP State, the microcontroller reset is released. Important: If any measurement is active while an enabled interrupt occurs (e.g., the sleep timer expires) the measurement is interrupted and the system returns to the FP State. Note: If register discCvtCnt is set to 0, voltage and temperature are measured in each loop (default setting). Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 56 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.7 LP/ULP State Performing Current, Voltage, and Temperature Measurements with discCvtCnt == 2 I gotoPd Command ADC Trigger Time FP Wakeup Due to Sleep Timer Interrupt LP / ULP Current measurement only FP t Measurement of current, voltage and temperature Figure 3.8 LP/ULP State Performing Current, Voltage, and Temperature Measurements with discCvtCnt == 5 I gotoPd Command ADC Trigger Time FP LP / ULP Current measurement only Data Sheet July 10, 2014 Wakeup due to Voltage, Temperature or Current ADC Interrupt FP t Measurement of current, voltage, and temperature © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 57 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.9 LP/ULP State Performing Current, Voltage, and Temperature Measurements with discCvtCnt == 1 I gotoPd Command ADC Trigger Time FP LP / ULP Current measurement only 3.7.2.4 Wakeup Due to Current ADC Interrupt FP t Measurement of current, voltage and temperature Performing Discrete Measurements of Current, Voltage, and External Temperature during LP/ULP State During the LP or ULP State, the system can be configured to periodically enable both ADCs and measure current, voltage, and external temperature. This setup is the same as the configuration described in the previous section, except that the external instead of the internal temperature is measured. To use this option, pdMeas must be set to 3. 3.7.2.5 Performing Continuous Measurements of Current during LP/ULP State The system can be configured to perform continuous current measurements during the LP or ULP State. While the current ADC is powered up during the entire power-down state, the voltage/temperature ADC is powered down. The current ADC is powered up on entering the LP/ULP State if it was not already powered up during the FP State. The ADC trigger timer is not enabled as the measurement is continuous. Possible wake-up sources during this scenario are the watchdog timer interrupt, the sleep timer interrupt, the LIN wakeup interrupt (for ZSSC1750 only), or any of the ADC interrupts related to current. Important: If no interrupt is enabled, the system cannot wake up. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 58 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) To go to the LP or ULP State with continuous current measurements, the following tasks must be done: Enable at least one of the following interrupts: Set irqEna[0] to 1 to enable the watchdog interrupt to wake up the system. Set irqEna[1] to 1 to enable the sleep timer to wake up the system. Set irqEna[4] to 1 to enable the LIN wake-up detector and to enable the system to wake up due to a LIN wakeup frame (for ZSSC1750 only). Enable any ADC interrupt related to current (see section 3.6.1.1). Setup the sleep timer compare value (register sleepTCmp) if needed. Configure the pwrCfgLp register as follows: Set pdState to 0 or 1 to configure LP State or to 2 to configure ULP State. Set pdMeas to 4 to configure the system to perform continuous current measurements. Set lpEnaLp, ulpEnaLp, and pwrRefbufOcLp as needed. Write A9HEX to register gotoPd and then drive the CSN line high. When an enabled interrupt occurs, the system wakes up and the settings from register pwrCfgFp are restored. When all blocks have stabilized, the external microcontroller clock is re-enabled and if coming out of ULP State, the microcontroller reset is released. Important: If any measurement is active while an enabled interrupt occurs (e.g., the sleep timer expires), the measurement is interrupted and the system returns to FP State. Figure 3.10 LP/ULP State Performing Continuous Current-Only Measurements Note: The sleep timer interrupt or an ADC interrupt related to current is used as the wake-up source in this example, but it could also be the watchdog timer interrupt or the LIN wakeup interrupt (ZSSC1750 only). I gotoPd Command Current measurement only FP Data Sheet July 10, 2014 LP / ULP Wakeup Due to Sleep Timer or Current ADC Interrupt FP © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. t 59 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.7.2.6 Performing Continuous Current and Voltage Measurements during LP/ULP State The system can be configured to perform continuous current and voltage measurements during the LP or ULP State. Both ADCs are powered up during the entire power-down state. The ADCs are powered up on entering the LP/ULP State if they were not already powered up during the FP State. The ADC trigger timer is not enabled as the measurement is continuous. Possible wake-up sources during this scenario are the watchdog timer interrupt, the sleep timer interrupt, the LIN wakeup interrupt (for ZSSC1750 only), or any of the ADC interrupts related to current or voltage. Important: If no interrupt is enabled, the system cannot wake up. To go to LP or ULP State and perform continuous current and voltage measurements, follow these steps: Enable at least one of the following interrupts: Set irqEna[0] to 1 to enable the watchdog interrupt to wake up the system. Set irqEna[1] to 1 to enable the sleep timer to wake up the system. Set irqEna[4] to 1 to enable the LIN wake-up detector and to enable the system to wake up due to a LIN wakeup frame (for ZSSC1750 only). Enable any ADC interrupt related to current. Set up the sleep timer compare value (register sleepTCmp) if needed. Configure the pwrCfgLp register as follows: Set pdState to 0 or 1 to configure the LP State or to 2 to configure the ULP State. Set pdMeas to 5 to configure the system to perform continuous current and voltage measurements. Set lpEnaLp, ulpEnaLp, and pwrRefbufOcLp as needed. Write A9HEX to register gotoPd and then drive the CSN line high. When an enabled interrupt occurs, the system wakes up and the settings from register pwrCfgFp are restored. When all blocks have stabilized, the external microcontroller clock MCU_CLK is re-enabled and if coming out of ULP State, the microcontroller reset MCU_RST is released. Important: If any measurement is active while an enabled interrupt occurs (e.g., the sleep timer expires), the measurement is interrupted and the system returns to the FP State. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 60 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.11 Performing Continuous Current and Voltage Measurements during LP/ULP State Note: The sleep timer interrupt or an ADC interrupt related to voltage or current is used as the wake-up source in this example, but it could also be the watchdog timer interrupt or the LIN wakeup interrupt (for ZSSC1750 only). I gotoPd Command Measurement of current and voltage FP 3.7.2.7 LP / ULP Wakeup Due to Sleep Timer, Voltage ADC, or Current ADC Interrupt FP t Performing Continuous Measurements of Current and Internal Temperature during LP/ULP State This setup is the same as the configuration described in the previous section, except that the internal temperature instead of the voltage is measured. To use this option, pdMeas must be set to 6. Possible wake-up sources during this scenario are the watchdog timer interrupt, the sleep timer interrupt, the LIN wakeup interrupt (for ZSSC1750 only), or any of the ADC interrupts related to current or temperature. 3.7.2.8 Performing Continuous Measurements of Current and External Temperature during LP/ULP State This setup is the same as the configuration described in the previous section, except that the external temperature instead of the internal temperature is measured. To use this option, pdMeas must be set to 7. Possible wake-up sources during this scenario are the watchdog timer interrupt, the sleep timer interrupt, the LIN wakeup interrupt (for ZSSC1750 only), or any of the ADC interrupts related to current or temperature. 3.7.3 OFF State The OFF State is the power-down state with the lowest current consumption, and no ADC measurements are possible. It is intended for long periods of inactivity; e.g., when a car is shipped around the world. During this state, all oscillators and clocks are turned off, the external microcontroller is not powered, and most of the analog blocks are powered down. Only the SBC’s digital core and the RX part of the LIN PHY remain powered. The system can only wake up at the detection of a LIN wakeup frame (for ZSSC1750 only) or after power-on reset (for ZSSC1750/51). To go to the OFF State, the following tasks must be done: Set irqEna[4] to 1 to enable the LIN wake-up detector and to enable the system to wake up due to a LIN wakeup frame (for ZSSC1750 only). Set pdState to 3 to configure the OFF State as the power-down state to be entered. Write A9HEX to register gotoPd and drive the CSN line high. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 61 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) For the ZSSC1750 only, when the LIN RXD line goes low during the OFF State, the low-power oscillator is reenabled and the digital logic checks if the LIN RXD line is low for a time equal or more than 150µs. If this is true, the complete system returns to the FP State and the external microcontroller is powered up, reset, and clocked again. If the LIN RXD line was low for less than 150µs, the low-power oscillator is powered down again and the system remains in OFF State. Important: If the LIN wakeup interrupt is not enabled, the system only can only wake up by a power-on reset. 3.7.4 Registers for Power Configuration and the Discreet Current Measurement Count 3.7.4.1 Register “pwrCfgFp” – Power Configuration Register for the FP State Table 3.18 Register pwrCfgFp Name Address Bits Default Access pwrAdcI pwrAdcV [0] [1] 0BIN 0BIN RW RW Reserved lpEnaFp [2] [3] 0BIN 0BIN RW RW 53HEX ulpEnaFp pdRefbufOcFp Unused Data Sheet July 10, 2014 [4] 0BIN RW [5] 0BIN RW [7:6] 00BIN RO Description When set to 1, the current ADC is powered. When set to 1, the voltage/temperature ADC is powered. Reserved; always write as 0. When set to 1, the bias current of the analog blocks is reduced to 10% in the FP State. Note: if ulpEnaFp is also set to 1, the bias current of the analog blocks is reduced to 15%. When set to 1, the bias current of the analog blocks is reduced to 5% in the FP State. Note: if lpEnaFp is also set to 1, the bias current of the analog blocks is reduced to 15%. When set to 1, the offset cancellation of the reference buffer is powered down. Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 62 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.7.4.2 Register “pwrCfgLp” – Power Configuration Register for Power-Down States Table 3.19 Register pwrCfgLp Name Address Bits Default Access pdState [1:0] 00BIN RW pdMeas [4:2] 000BIN RW lpEnaLp [5] 1BIN RW ulpEnaLp [6] 0BIN RW pwrRefbufOcLp [7] 0BIN RW 64HEX Data Sheet July 10, 2014 Description Select the power-down state to be entered: 0 or 1 LP State 2 ULP State 3 OFF State Type of measurements to be performed during the LP or ULP State: 0 No measurements 1 Discrete measurements of current 2 Discrete measurements of current, voltage, and internal temperature 3 Discrete measurements of current, voltage, and external temperature 4 Continuous measurements of current 5 Continuous measurements of current and voltage 6 Continuous measurements of current and internal temperature 7 Continuous measurements of current and external temperature When set to 1, the bias current of the analog blocks is reduced to 10% in the LP/ULP State. Note: if ulpEnaLp is also set to 1, the bias current of the analog blocks is reduced to 15%. When set to 1, the bias current of the analog blocks is reduced to 5% in the LP/ULP State. Note: If lpEnaLp is also set to 1, the bias current of the analog blocks is just reduced to 15%. When set to 1, the offset cancellation of the reference buffer is powered in LP/ULP State while performing measurements. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 63 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.7.4.3 Register “gotoPd” – Enter Power-Down State Table 3.20 Register gotoPd Name Address Bits Default Access gotoPd 65HEX [7:0] 00HEX WO 3.7.4.4 Description Writing A9HEX to this register triggers the PMU to enter the configured power-down state when the CSN line is driven high. Register “discCvtCnt” – Configuration Register for Discrete Measurements Table 3.21 Register discCvtCnt Name discCvtCnt 3.8 Address Bits Default Access 5FHEX [7:0] 00HEX RW Description Defines the number of "current only" measurements before performing one measurement of current, voltage, and temperature when pdMeas is 2 or 3. ZSSC1750/51 ADC Unit The measurement subsystem incorporates two independent and synchronized high-resolution ADCs for monitoring two channels (SD_ADC blocks). The conversion scheme is based on the sigma-delta modulation (SDM) principle. One channel (ADC-I) is exclusively used for current measurement and includes a pre-amplifier with offset cancellation circuitry. The second channel (ADC-V/T) can be programmed for measuring either voltage or temperature (internal or external). The raw conversion data can be post-processed by calibration data to achieve a minimum offset and gain error (gain and offset correction). The conversion results are stored in the register file from which they can be read via the SPI digital communication interface. A completed conversion is flagged by a “data ready” signal that can be used as an interrupt source for the external microcontroller. A functional block diagram of the analog circuitry is shown in Figure 3.12. The purpose of this analog architecture is to achieve a maximum level of diagnostic capability and flexibility as well as best accuracy. The digital ADC unit consists of the data processing unit and control logic. The control logic generates the clocks and control signals for the analog SD-ADCs as well as control signals for the data processing part of the ADC unit. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 64 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.12 Functional Block Diagram of the Analog Measurement Subsystem cSel VDDA cSel VSSA IM fINT / fDEC INP IPZ1 INN IPZ2 VSSA fiSC fiSC MPX1 PA-C PGA-2 PGA-1 sinc4 Digital Filter -Modulator-1 MPX2 VREF 1.2V VCM pd_vbat VSSA VREFLP 1.2V fSDM VREF 1.2V VCM VBAT pd_inamp VSSA SC-Clock Generator VBATP VDDA VBATN RREF NTH RNTC CVDA MPX3 IPZ3 -Modulator-2 IPZ4 NTL pdExtTemp fINT / fDEC fiSC sinc4 Digital Filter VPTAT On-Chip Temperature Sensor Analog-2-Digital Conversion PA-T vtSel VSSA VCM=VDDA/2 PA-C = Preamplifier Current; PA-T = Preamplifier Temperature; MPX = Multiplexer; PGA = Programmable Gain Amplifier 3.8.1 ADC Clocks Two clocks are generated in the digital part of the ADC unit and are driven to the analog part. The SDM clock is used for both SD-ADCs. The chop clock is used for the chopping operation within the SD-ADCs. The base for both clocks is the multiplexed clock muxClk, which is a 4MHz clock in FP State and a 125kHz clock in LP/ULP State. 3.8.1.1 ADC Clocks in FP State In the FP State, the SDM clock is generated from the 4MHz clock by dividing it by two times the value programmed into bit field sdmClkDivFp in register sdmClkCfgFp (see Table 3.24): fSDM fHP 2 sdmClkDivFp fHP 4 MHz (4) Important: When sdmClkDivFp is set to 0, the frequency of SDM clock is 2MHz. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 65 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) The chop clock is generated from the SDM clock by further dividing it by 2, 4, 8, or 16 depending on the setting of the sdmChopClkDiv field in register adcGomd (see Table 3.55): fCHOP fSDM 2 -( sdmClkChopDiv1) (5) Although the clock bases used to generate the SDM and the chop clock have a frequency of 4MHz, the position of the clock edges used for the clock generation can be shifted relative to the 4MHz clock used for the digital logic to obtain optimal noise behavior for the analog section. The 4MHz clock used to generate the SDM clock (CLKSDMBASE) is delayed relative to the 4MHz clock used for the digital logic (CLKMUXCLK) by one to four 20MHz clock cycles (CLKHPOSC) depending on the settings of the field sdmPos in register sdmClkCfgFp (Table 3.24). The 4MHz clock used to generate the chop clock (CLKCHOPBASE) is delayed relative to the 4MHz clock used for the digital logic (CLKSDMBASE) by zero to four 20MHz clock cycles depending on the settings of field sdmPos2 and field sdmPos in register sdmClkCfgFp. The delay in the number of 20MHz clock cycles of the chop clock relative to the SDM clock can be calculated using the following formula: delay (sdmPos2- sdmPos) mod5 (6) Important: The delay programmed into field sdmPos2 is related to CLKMUXCLK, not to CLKSDMBASE. Table 3.22 shows the value that must be programmed into field sdmPos2 depending on the field sdmPos and the desired delay. Table 3.22 Value for sdmPos2 Depending on sdmPos and Desired Clock Delay from SDM to Chop Clock Delay 0 1 2 3 4 Data Sheet July 10, 2014 sdmPos =0 0 1 2 3 4 sdmPos2 sdmPos =1 sdmPos=2 1 2 2 3 3 4 4 0 0 1 sdmPos=3 3 4 0 1 2 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 66 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.13 FP ADC Clocking Scheme for sdmPos = sdmPos2 = 2; sdmClkDivFp = 1; sdmChopClkDiv = 0 CLKHPOSC CNT 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 CLKMUXCLK CLKSDMBASE CLKCHOPBASE SDM clock CHOP clock Figure 3.14 FP ADC Clocking for sdmPos = 1 and sdmPos2 = 4; sdmClkDivFp = 1; sdmChopClkDiv = 0 CLKHPOSC CNT 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 CLKMUXCLK CLKSDMBASE CLKCHOPBASE SDM clock CHOP clock Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 67 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.15 FP ADC Clocking for sdmPos = 3 and sdmPos2 = 0; sdmClkDivFp = 1; sdmChopClkDiv = 0 CLKHPOSC CNT 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 CLKMUXCLK CLKSDMBASE CLKCHOPBASE SDM clock CHOP clock Figure 3.16 FP ADC Clocking for sdmPos = 0 and sdmPos2 = 3; sdmClkDivFp = 1; sdmChopClkDiv = 0 CLKHPOSC CNT 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 CLKMUXCLK CLKSDMBASE CLKCHOPBASE SDM clock CHOP clock 3.8.1.2 ADC Clocks in the LP/ULP State In the LP or ULP State, the SDM clock is generated from the 125 kHz clock (CLKLPOSC) by dividing it by two times the value programmed into register sdmClkDivLp (see Table 3.23): fSDM fLP ; fLP 125kHz 2 sdmClkDivLp (7) Important: When sdmClkDivLp is set to 0, the frequency of the SDM clock is 62.5 kHz. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 68 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) The chop clock is generated from the SDM clock by further dividing it by 2, 4, 8, or 16 depending on the setting of the sdmChopClkDiv field in register adcGomd: fCHOP fSDM 2-( sdmChopClk Div 1) (8) Both the SMD and chop clocks are generated from the same 125kHz clock that is used for the digital logic. Shifting of the clocks used to generate the SDM and chop clock is not possible and not needed as the analog clocks are generated on the falling clock edge where the digital logic is already stable and will not influence the analog section. Figure 3.17 LP/ULP ADC Clocking Scheme; sdmClkDivLp = 5; sdmChopClkDiv = 0 CLKLPOSC SDM clock CHOP clock 3.8.1.3 Register “sdmClkCfgLp” – Configuration Register for the SDM Clocks in the LP/ULP State Table 3.23 Register sdmClkCfgLp Name sdmClkDivLp[7:0] sdmClkDivLp[9:8] Address Bits Default Access B0HEX [7:0] [1:0] 18HEX 00BIN RW RW B1HEX Unused 3.8.1.4 [7:2] 00 0000BIN RO Description Clock divider value for the SDM clock in the LP and ULP States related to the 125KHz base clock. With sdmClkDivLP = 0, the divider value is 2. Unused; always write as 0. Register “sdmClkCfgFp” – Configuration Register for the SDM Clocks in the FP State Table 3.24 Register sdmClkCfgFp Name sdmClkDivFp[7:0] sdmClkDivFp[9:8] Unused sdmPos2 sdmPos Data Sheet July 10, 2014 Address Bits Default Access B2HEX [7:0] [1:0] 08HEX 00BIN RW RW [2] [5:3] 0BIN 010BIN RO RW [7:6] 10BIN RW B3HEX Description Clock divider value for the SDM clock in the FP State related to the 4MHz base clock fHP. If 0, then the SDM clock is 2MHz. Unused; always write as 0 Position of the chop clock (CLKCHOPBASE) relative to the base clock CLKMUXCLK (possible values = 0 to 4) Position of the SDM clock (CLKSDMBASE) relative to the base clock CLKMUXCLK © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 69 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.2 ADC Data Path nd rd The incoming 2 and 3 order bit streams from the analog part of the SD-ADCs are first captured and then rd driven through a 3 order noise shaping filter as illustrated in Figure 3.18. The digital conversion is accomplished th 4 by a 4 order low-pass filter (sinc decimation filter). The bit stream capturing and the noise shaping filter cannot be directly changed by the user (no configuration registers), but the selected oversampling rate (adcSamp 4 register field osr) affects the sinc decimation filter (one output value per N input values). Figure 3.18 Functional Block Diagram of the Digital ADC Data Path {000, BIST bitstream} {000, BIST bitstream} SDM 1 SDM 2 Bitstream Capture Bitstream Capture Noise Cancellation Noise Cancellation 4 4 4 4 sinc 4 Decimation sinc Filter Decimation Filter 4 Post Filter Post Filter Data Post Correction Result Register 4 A simple post filter (moving average filter) is placed behind the sinc decimation filter. The user can select the averaging function (no averaging; 2-stage averaging; or 3-stage averaging) via the avgFiltCfg bit field in the adcSamp register (see Table 3.56) when chopping is disabled (see section 3.8.4.4). When chopping is enabled, the 2-stage averaging is used independently of the filter configuration. The function of the 2-stage averaging filter is x in (t) x in (t - 1) 2 The function of the 3-stage averaging filter is x out (t) xin (t ) 2 xin ( t - 1) x in ( t - 2) 4 Where t = current sample x out (t ) (9) (10) t-1 = previous sample t-2 = sample before previous sample, etc. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 70 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.2.1 Data Post-Correction Block The data post-correction block performs the offset and gain correction of the post-filtered conversion data as well as the over-range and the overflow detection. Post-Filter Channel 2 x x tempPoCoGain voltPoCoGain curPoCoGain adcTgan adcVgan adcCgan adcToff adcVoff + Overflow Check Post-Filter Channel 1 Over-Range Check adcCoff Figure 3.19 Data Post Correction First, an over-range check is performed on the incoming data. Values that are outside the interval [-0.75; 0.75) are always mapped to the corresponding interval boundary. This is done for better results as the ADC accuracy decreases for large input values. The user can enable a “set interrupt” strobe for each of the two channels by setting the adcAcmp register bits COvrEna and VTOvrEna to 1 (see Table 3.54). Note: The “set interrupt” strobes go to the interrupt controller. They have a different meaning than the corresponding “interrupt enable” bits (interrupt bits [15:14] in the irqEna register). The “set interrupt” bits are used to select whether the interrupt status bits will be set or not; the “interrupt enable” bits select whether the interrupt status bits will drive the interrupt line or not. After the over-range check, a programmable offset, interpreted as a number in the range [-1.0; 1.0), is added to the data. Three registers allow setting different offsets for current, voltage, and temperature: adcCoff, adcVoff, and adcToff (see Table 3.25, Table 3.27, and Table 3.29 respectively). The offset correction is followed by two multiplication stages. In the first multiplication stage, individual gain factors for current (adcCgan), voltage (adcVgan), or temperature (adcTgan), interpreted as numbers in the range [0.0; 2.0), are multiplied by the offset corrected data (see Table 3.26, Table 3.28, and Table 3.30 respectively). The second multiplication stage is used to shift the significant data into the most significant bits of the result register. The data is multiplied by 1, 2, 4, or 8, which can be individually selected for current, voltage, and temperature via the curPoCoGain, voltPoCoGain, and tempPoCoGain fields in the adcPoCoGain register (see Table 3.31). Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 71 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.20 Data Representation through Data Post Correction including Over-Range and Overflow Levels Note: the yellow area represents the usable data space to avoid overflow when the post correction gain is 2. 1 2.4V 3/4 1.8V 1/2 1.2V 0 0.0V Input to Data Post-Correction Gain and Offset Correction Post-Correction FFFFFFHEX 7FFFFFHEX 7FFFFFHEX 600000HEX 600000HEX C00000HEX 400000HEX 400000HEX 800000HEX 000000HEX 000000HEX C00000HEX C00000HEX A00000HEX A00000HEX 000000HEX 800000HEX 800000HEX Unsigned Signed Signed Overflow E00000HEX Over-Range poCoGain = 2 -1/2 -1.2V -3/4 -1.8V -1 -2.4V 400000HEX 200000HEX Over-Range Overflow An overflow check is performed on the output of the second multiplication stage as the result might be out of the representable range of [-1.0; 1.0). The user can also enable a “set interrupt” strobe for each of the two channels by setting the adcAcmp register bits COvrEna and/or VTOvrEna to 1 (same bits as for the over-range check). Note: Although the same “set interrupt strobe enable” bit is used for over-range and overflow, independent interrupt status bits can be individually enabled or disabled. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 72 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.21 illustrates the common enable CovrEna for the interrupt strobes for current over-range and overflow. The function of VTOvrEna as the common enable for the interrupt strobes for voltage/temperature over-range and overflow conditions is similar. Figure 3.21 Common Enable for the “set overrange” and “set overflow” Interrupt Strobes for Current current overflow detected & set interrupt irqStat[12] (current overflow) COvrEna current overrange detected 3.8.2.2 & set interrupt irqStat[14] (current overrange) Register “adcCoff” – Offset Correction Value for Current Channel Table 3.25 Register adcCoff Name adcCoff[7:0] adcCoff[15:8] adcCoff[23:16] 3.8.2.3 Address Bits Default Access 33HEX 34HEX 35HEX [7:0] [7:0] [7:0] 00HEX 00HEX 00HEX RW RW RW Description Offset value for current value; interpreted as a number in the range [-1.0; 1.0) formatted in 2’s complement representation. Programmable offset range = +/- 2 VREF; VREF= full-scale range ADC. Note: The initial value is loaded from OTP after reset. Register “adcCgan” – Gain Correction Value for Current Channel Table 3.26 Register adcCgan Name adcCgan[7:0] adcCgan[15:8] adcCgan[23:16] 3.8.2.4 Address Bits Default Access 30HEX 31HEX 32HEX [7:0] [7:0] [7:0] 00HEX 00HEX RW RW RW 80HEX Description Gain value for current value; interpreted as a number in the range [0.0; 2.0). Note: The initial value is loaded from OTP after reset. Register “adcVoff” – Offset Correction Value for Voltage Channel Table 3.27 Register adcVoff Name adcVoff[7:0] adcVoff[15:8] adcVoff[23:16] Data Sheet July 10, 2014 Address Bits Default Access 39HEX 3AHEX 3BHEX [7:0] [7:0] [7:0] 00HEX 00HEX 00HEX RW RW RW Description Offset value for voltage value; interpreted as a number in the range [-1.0; 1.0) formatted in 2’s complement representation. Programmable offset range = +/- 2 VREF; VREF= full-scale range ADC. Note: The initial value is loaded from OTP after reset. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 73 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.2.5 Register “adcVgan” – Gain Correction Value for Voltage Channel Table 3.28 Register adcVgan Name adcVgan[7:0] adcVgan[15:8] adcVgan[23:16] 3.8.2.6 Address Bits Default Access 36HEX 37HEX 38HEX [7:0] [7:0] [7:0] 00HEX 00HEX RW RW RW 80HEX Description Gain value for voltage value; interpreted as a number in the range [0.0; 2.0) Note: The initial value is loaded from OTP after reset. Register “adcToff” – Offset Correction Value for Temperature Channel Table 3.29 Register adcToff Name Address adcToff[7:0] adcToff[15:8] 3EHEX 3FHEX Bits Default Access [7:0] [7:0] 00HEX 00HEX RW RW Description Offset value for temperature value; interpreted as a number in the range [-1.0; 1.0) Note: The initial value is loaded from OTP after reset. 3.8.2.7 Register “adcTgan” – Gain Correction Value for Temperature Channel Table 3.30 Register adcTgan Name adcTgan[7:0] adcTgan[15:8] Address Bits Default Access 3CHEX 3DHEX [7:0] [7:0] 00HEX RW RW 80HEX Description Gain value for temperature value; interpreted as a number in the range [0.0; 2.0) Note: The initial value is loaded from OTP after reset. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 74 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Register “adcPoCoGain” – Post Correction Gain Configuration 3.8.2.8 Table 3.31 Register adcPoCoGain Name Address Bits Default Access curPoCoGain [1:0] 00BIN RW voltPoCoGain [3:2] 00BIN RW tempPoCoGain [5:4] 00BIN RW Unused [7:6] 00BIN RO 57HEX 3.8.3 Description Post correction gain for the current channel: 0 Gain factor is 1 1 Gain factor is 2 2 Gain factor is 4 3 Gain factor is 8 Post correction gain for the voltage channel: 0 Gain factor is 1 1 Gain factor is 2 2 Gain factor is 4 3 Gain factor is 8 Post correction gain for the temperature channel: 0 Gain factor is 1 1 Gain factor is 2 2 Gain factor is 4 3 Gain factor is 8 Unused; always write as 0. ADC Operating Modes and Result Registers 3.8.3.1 Single Measurement Results Each value coming from the data post-correction block is the result of a single measurement. These values are signed and stored in the corresponding result registers adcCdat, adcVdat, adcTdat, or adcRdat (see Table 3.32 through Table 3.35).The following formulas can be used to calculate the battery current and the battery voltage from the result register values: IBAT adcCdat 2 VREF 23 RSHUNT 2 GANA GPOCO (11) adcVdat 24 2 VREF 23 2 GPOCO (12) VBAT Where: IBAT VBAT GANA GPOCO RSHUNT VREF adcCdat adcVdat Data Sheet July 10, 2014 Battery current Battery voltage Analog gain in current path (pgaIfc pga1 pga2; see Table 3.36) Digital gain in post-correction stage (second multiplication; see Table 3.31) Shunt resistance Reference voltage Register value for current Register value for voltage © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 75 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.2 Register “adcCdat” – Single Current Measurement Value Table 3.32 Register adcCdat Name adcCdat[7:0] adcCdat[15:8] adcCdat[23:16] 3.8.3.3 Address Bits Default Access 02HEX 03HEX 04HEX [7:0] [7:0] [7:0] 00HEX 00HEX 00HEX RO RO RO Description Conversion result of a single current measurement (signed value) Register “adcVdat” – Single Voltage Measurement Value Table 3.33 Register adcVdat Name Address adcVdat[7:0] adcVdat[15:8] adcVdat[23:16] 3.8.3.4 05HEX 06HEX 07HEX Bits Default Access [7:0] [7:0] [7:0] 00HEX 00HEX 00HEX RO RO RO Description Conversion result of a single voltage measurement (signed value) Registers “adcTdat” and “adcRdat” – Single Temperature Measurement Values Table 3.34 Register adcTdat Name adcTdat[7:0] adcTdat[15:8] Address Bits Default Access 0AHEX 0BHEX [7:0] [7:0] 00HEX 00HEX RO RO Address Bits Default Access 08HEX 09HEX [7:0] [7:0] 00HEX 00HEX RO RO Description Conversion result of a single temperature value (signed value; inverted); this value is either the internally measured temperature or the NTC value of an external temperature measurement. Important: This value is sign-inverted. Table 3.35 Register adcRdat Name adcRdat[7:0] adcRdat[15:8] Data Sheet July 10, 2014 Description Conversion result of a single temperature measurement by reading a voltage across the reference resistor (external temperature measurement only). © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 76 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.5 Register “adcGain” – Analog Gain Configuration in the Current Path Table 3.36 Register adcGain Name Address Bits Default Access pgaIfc [1:0] 00BIN RW pga1 [3:2] 00BIN RW [4] 0BIN RW [7:5] 000BIN RO 52HEX pga2 Unused 3.8.3.6 Description Sets the gain of the PA-C preamplifier in the analog current path: 0 Gain factor is 1 1 Gain factor is 2 2 Gain factor is 4 3 Gain factor is 8 Sets the gain of the PGA-1 programmable gain amplifier in the analog current path: 0 Gain factor is 1 1 Gain factor is 2 2 Gain factor is 4 3 Gain factor is 8 Sets the gain of PGA-2 programmable gain amplifier in the analog current path: 0 Gain factor is 4 1 Gain factor is 8 Unused; always write as 0. Result Counter Functionality and Conversion Ready Strobes Three status bits are available in the interrupt status (irqStat[7:5]) that signal that the conversion of current, voltage, or temperature has been completed. The “set interrupt” strobe is generated for each completed temperature measurement. For the voltage and current measurements, the user can independently select whether the corresponding “set interrupt” strobe will be generated after each single measurement (SRCS – single result count sequence) or after N measurements (MRCS – multi-result count sequence). The register adcCrcl configures the number of current measurements before the current conversion ready strobe is generated; the maximum number is 65535 (see Table 3.37). Setting this register to 0 disables the result count functionality, which means that SRCS is configured. The present result counter value can always be read from the register adcCrcv (see Table 3.38). The result counter is reset when the bit field startAdcC in register adcCtrl is set (rising edge) in the FP State (see Table 3.58) or at the start of the first measurement in LP/ULP State. It is set to 1 at the end of the first measurement after the limit defined in adcCrcl has been reached. The register adcVrcl configures the number of measurements before the voltage conversion ready strobe is generated, the maximum number is 15 (see Table 3.39). Setting this register to 0 disables the result count functionality, which means that SRCS is configured. The present result counter value can always be read from the register adcVrcv (see Table 3.40). The result counter is reset when startAdcV in register adcCtrl is set (rising edge) in the FP State or at the start of the first measurement in the LP/ULP State. It is set to 1 at the end of the first measurement after the limit defined in adcVrcl was reached. Note: Setting register adcCrcl or adcVrcl to 1 also leads to SRCS in the corresponding channel. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 77 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.7 Register “adcCrcl” – Current Result Count Limit Table 3.37 Register adcCrcl Name adcCrcl[7:0] adcCrcl[15:8] Address Bits Default Access 40HEX 41HEX [7:0] [7:0] 00HEX 00HEX RW RW Description Number of current measurements before the current conversion ready strobe is generated. Note: Setting this bit to 0 disables this functionality, and the strobe is generated after each current measurement. 3.8.3.8 Register “adcCrcv” – Current Result Count Value Table 3.38 Register adcCrcv Name adcCrcv[7:0] adcCrcv[15:8] 3.8.3.9 Address Bits Default Access 1BHEX 1CHEX [7:0] [7:0] 00HEX 00HEX RO RO Description Present value of the current result counter. Register “adcVrcl” – Voltage Result Count Limit Table 3.39 Register adcVrcl Name Address adcVrcl Bits Default Access [3:0] 0000BIN RW 45HEX Unused [7:4] 0000BIN RO Description Number of voltage measurements before the voltage conversion ready strobe is generated. Note: Setting this bit to 0 disables this functionality, and the strobe is generated after each voltage measurement. Unused; always write as 0. 3.8.3.10 Register “adcVrcv” – Voltage Result Count Value Table 3.40 Register adcVrcv Name adcVrcv Unused Data Sheet July 10, 2014 Address Bits Default Access 1EHEX [3:0] [7:4] 0000BIN 0000BIN RO RO Description Present value of the voltage result counter. Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 78 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.11 Current Threshold Comparator Functionality The current threshold comparator functionality is used to monitor the current level and to generate an interrupt (irqStat[8]) if the absolute current value exceeds a programmable limit for a configurable number of conversion results. This functionality is enabled if the field ctcvMode in register adcAcmp is set to a non-zero value (see Table 3.54Table 3.58). If enabled, this function is always triggered when a new current value is measured. The absolute value of the most significant 17 bits of the measured current value is compared to the expanded programmable threshold register adcCrth (see Table 3.41): absadcCdat 23 : 7 0, adcCrth (13) When the current threshold comparator functionality is enabled, the current threshold counter is used to count the number of conversions where the absolute current value is above the threshold. If the absolute current value is greater than or equal to the programmed threshold (above formula is true), the internal current threshold counter is incremented (until it reaches its maximum value FFHEX). Otherwise the counter is either decremented (if ctcvMode field in register adcAcmp set to 1) or reset (if ctcvMode set to 2), or it remains unchanged (if ctcvMode set to 3). The present value of the current threshold counter can be read from the register adcCtcv (see Table 3.43). Note: When bit field ctcvMode in register adcAcmp is set to 00BIN, the current threshold comparator functionality is disabled and register adcCrtv is always 0. Note: When ctcvMode is set to 01BIN, the current threshold counter is not decremented when the counter is 0. After each comparison of the absolute current value versus the current threshold level and after the current threshold counter has been updated, the internal current threshold counter is compared to the current threshold counter limit (register adcCtcl; see Table 3.42). Whenever the current threshold counter is greater than or equal to the programmable limit, a “set interrupt” strobe is generated. Note: When the current threshold counter has reached its limit and it is configured to keep its value if the limit is not reached, a “set interrupt” strobe is generated for each new measurement even if the new value is below threshold. The current threshold counter is reset to 0 for the following conditions: If ctcvMode is set to 2 and the absolute current value is below the programmed threshold adcCrth On assertion of startAdcC (rising edge) in the FP State At the start of the first conversion in the LP or ULP State Each time the result counter is reset (if the result counter is enabled) and the current threshold counter reset mode bit (bit ctcvRstMode in register adcAcmp) is set to 1 Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 79 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.12 Register “adcCrth” – Absolute Current Threshold Table 3.41 Register adcCrth Name adcCrth[7:0] adcCrth[15:8] Address Bits Default Access 42HEX 43HEX [7:0] [7:0] 00HEX 00HEX RW RW Description Absolute current threshold (unsigned value). When using current comparator threshold functionality, the absolute current value is compared to {0, adcCrth}. 3.8.3.13 Register “adcCtcl” – Current Threshold Counter Limit Table 3.42 Register adcCtcl Name Address Bits Default Access adcCtcl 44HEX [7:0] 00HEX RW Description Current threshold counter limit. This register defines the number of current measurements that must be greater than or equal to the threshold adcCrth before the interrupt is set. 3.8.3.14 Register “adcCtcv” – Current Threshold Counter Value Table 3.43 Register adcCtcv Name adcCtcv Address Bits Default Access 1DHEX [7:0] 00HEX RO Description Present current threshold counter value. 3.8.3.15 Current Accumulator Functionality The current accumulator functionality is used to sum up all current conversion results. The present accumulator value can be read from the register adcCaccu (signed value; see Table 3.45). Positive conversion results increment the accumulator register, negative conversion results decrement it. The accumulator register saturates at its minimum and maximum value. The current accumulator is reset to 0 under these conditions: On assertion of startAdcC (rising edge) in the FP State At the start of the first conversion in the LP or ULP State Each time the result counter is reset (if the result counter is enabled) and the current accumulator reset mode bit (bit accuRstMode in register adcAcmp) is set to 1 Note: The current accumulator functionality can be used to calculate the mean value of the current. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 80 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) The current accumulator is also compared to a programmable signed accumulator threshold value (register adcCaccTh). This comparison can be used to generate a “set interrupt” strobe for irqStat[11]; however, to enable the generation of the “set interrupt” strobe, bit CAccuThEna in register adcAcmp must be set to 1 (see Table 3.54). The “set interrupt” strobe is always generated on update of the accumulator register when adcCaccTh is greater than 0 and adcCaccu is greater than adcCaccTh adcCaccTh is lower than 0 and adcCaccu is lower than adcCaccTh adcCaccTh is equal to 0 and adcCaccu is not equal to 0 3.8.3.16 Register “adcCaccTh” – Current Accumulator Threshold Value Table 3.44 Register adcCaccTh Name adcCaccTh[7:0] adcCaccTh[15:8] adcCaccTh[23:16] adcCaccTh[31:24] Address Bits Default Access 48HEX 49HEX 4AHEX 4BHEX [7:0] [7:0] [7:0] [7:0] 00HEX 00HEX 00HEX 00HEX RW RW RW RW Description Signed threshold value for current accumulator mode 3.8.3.17 Register “adcCaccu” – Current Accumulator Value Table 3.45 Register adcCaccu Name adcCaccu[7:0] adcCaccu[15:8] adcCaccu[23:16] adcCaccu[31:24] Address Bits Default Access 0CHEX 0DHEX 0EHEX 0FHEX [7:0] [7:0] [7:0] [7:0] 00HEX 00HEX 00HEX 00HEX RO RO RO RO Description Present current accumulator value 3.8.3.18 Voltage Threshold Comparator and Voltage Accumulator Functionality The ZSSC1750/51 also provides a threshold comparator as well as an accumulator comparator for the battery voltage channel but with reduced functionality. If the VThSel bit in register adcAcmp is set to 0, the absolute value of the most significant 17 bits of a single voltage measurement (register adcVdat) is compared to the programmable voltage threshold (register adcVTh; see Table 3.46). In this case, register adcVTh is interpreted as an unsigned value. There is also no counter functionality. Whenever the absolute voltage value is below the programmed threshold, a “set interrupt” strobe for irqStat[9] is generated if the strobe generation is enabled (the field VThWuEna in register adcAcmp is set to 1). absadcVdat 23 : 7 0, adcVTh (14) When bit VThSel in register adcAcmp is set to 1, the voltage accumulator functionality is enabled. The voltage result counter functionality must also be enabled (register adcVrcl > 0). The voltage accumulator functionality is used to sum up all voltage conversion results. In contrast to the current channel, only the upper 20 bits of the voltage conversion results are accumulated. The present accumulator value can be read from the register adcVaccu (signed value; see Table 3.47). Positive conversion results increment the accumulator register; negative conversion results decrement it. The accumulator register saturates at its minimum and maximum value. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 81 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) The voltage accumulator is reset to 0 under these conditions: On assertion of startAdcV (rising edge) in the FP State At start of the first conversion in the LP or ULP State Each time the result counter is reset (if the result counter is enabled) Note: The voltage accumulator functionality can be used to calculate the mean value of the voltage. After the last accumulation within an MRCS, the upper 16 bits of the voltage accumulator are compared to the voltage threshold adcVTh, which is interpreted as a signed value in this case. This comparison can be used to generate a “set interrupt” strobe for irqStat[9]; however, to enable the generation of the “set interrupt” strobe, bit VThWuEna in register adcAcmp must be set to 1. The “set interrupt” strobe is generated when adcVTh is greater than 0 and adcVaccu is less than or equal to adcVTh adcVTh is lower than 0 and adcVaccu is greater than or equal to adcVTh adcVTh is equal to 0 and adcVaccu is equal to 0 Important: The threshold adcVTh is either interpreted as an unsigned or signed value depending on the operation mode (VThSel). Note: The voltage comparators compare only on the MSBs of the conversion result, so it might be beneficial to use the post-correction gain functionality to shift left the results to increase the accuracy of the comparison. 3.8.3.19 Register “adcVTh” – Voltage Threshold Value Table 3.46 Register adcVTh Name adcVTh[7:0] adcVTh[15:8] Address Bits Default Access 46HEX 47HEX [7:0] [7:0] 00HEX 00HEX RW RW Description Voltage threshold. If VThSel == 0, then adcVTh is interpreted as an unsigned value and it is compared to the absolute value of a single voltage conversion. If VThSel == 1, then adcVTh is interpreted as a signed value and it is compared to the accumulated voltage conversion results at the end of an MRCS. 3.8.3.20 Register “adcVaccu” – Voltage Accumulator Value Table 3.47 Register adcVaccu Name adcVaccu[7:0] adcVaccu[15:8] adcVaccu[23:16] Data Sheet July 10, 2014 Address Bits Default Access 10HEX 11HEX 12HEX [7:0] [7:0] [7:0] 00HEX 00HEX 00HEX RO RO RO Description Present voltage accumulator value © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 82 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.21 Minimum and Maximum Values of Current and Voltage For current and voltage measurements, the minimum and maximum values are determined on the upper 16 bits of the corresponding conversion results. These values can be read from registers adcCmax, adcCmin, adcVmax, and adcVmin. These registers are reset in the same manner as the corresponding accumulator registers. These values are only provided for statistical reasons and can be used to assess the accumulated current or voltage values when used for mean value calculation. Note: As the minimum and maximum values are only determined on the 16 MSBs of the corresponding conversion results, it might be beneficial to use the post correction gain functionality to shift left the results to increase the accuracy of the comparison. 3.8.3.22 Register “adcCmax” – Maximum Current Value Table 3.48 Register adcCmax Name adcCmax[7:0] adcCmax[15:8] Address Bits Default Access 13HEX 14HEX [7:0] [7:0] 00HEX 80HEX RO RO Description Upper 16 bits of the maximum measured current value (signed value) 3.8.3.23 Register “adcCmin” – Minimum Current Value Table 3.49 Register adcCmin Name adcCmin[7:0] adcCmin[15:8] Address Bits Default Access 15HEX 16HEX [7:0] [7:0] FFHEX 7FHEX RO RO Description Upper 16 bits of the minimum measured current value (signed value) 3.8.3.24 Register “adcVmax” – Maximum Voltage Value Table 3.50 Register adcVmax Name adcVmax[7:0] adcVmax[15:8] Address Bits Default Access 17HEX 18HEX [7:0] [7:0] 00HEX 80HEX RO RO Description Upper 16 bits of the maximum measured voltage value (signed value) 3.8.3.25 Register “adcVmin” – Minimum Voltage Value Table 3.51 Register adcVmin Name adcVmin[7:0] adcVmin[15:8] Data Sheet July 10, 2014 Address Bits Default Access 19HEX 1AHEX [7:0] [7:0] FFHEX 7FHEX RO RO Description Upper 16 bits of the minimum measured voltage value (signed value) © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 83 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.26 Temperature Limits The user can define an upper (register adcTmax) and a lower (register adcTmin) limit for the external and internal temperature measurement. On each update of register adcTdat (see Table 3.34), the upper 8 bits are compared to the signed limit values. This can be used to generate a “set interrupt” strobe for irqStat[10] if the value for adcTdat is outside the interval [adcTmin; adcTmax] and the TWuEna bit in register adcAcmp is set to 1 (see Table 3.54). Note: The minimum and maximum values are only compared to the 8 MSBs of the conversion result, so it might be beneficial to use the post correction gain functionality to shift left the results to increase the accuracy of the comparison. Important: The value stored in register adcTdat is inverted: the value given in register adcTmax is the value for the lower temperature interrupt threshold and the value given in register adcTmin is the value for the higher temperature interrupt threshold. 3.8.3.27 Register “adcTmax” – Upper Boundary for Temperature Interval Table 3.52 Register adcTmax Name adcTmax Address Bits Default Access 4CHEX [7:0] 00HEX RW Description Lower boundary for the temperature interval compared to the upper bits of adcTdat. 3.8.3.28 Register “adcTmin” – Lower Boundary for Temperature Interval Table 3.53 Register adcTmin Name adcTmin Address Bits Default Access 4DHEX [7:0] 00HEX RW Description Upper boundary for the temperature interval compared to the upper bits of adcTdat. 3.8.3.29 Miscellaneous Registers The registers defined in the next three sections provide settings that enable interrupts or control various functions related to the ADCs. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 84 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.30 Register “adcAcmp” – ADC Function Enable Register Table 3.54 Register adcAcmp Name Address Bits Default Access [0] 0BIN RW [2:1] 00BIN RW CAccuThEna [3] 0BIN RW COvrEna [4] 1BIN RW VTOvrEna [5] 1BIN RW ctcvRstMode [6] 0BIN RW accuRstMode [7] 0BIN RW VThWuEna [0] 0BIN RW VThSel [1] 0BIN RW anaGndSw ctcvMode 4EHEX 4FHEX TWuEna Unused Data Sheet July 10, 2014 [2] 0BIN [7:3] 0 0000BIN RW RO Description If set to 1, the signal pdExtTemp (see Figure 3.12), which is normally controlled by the PMU, is forced to 1. In this case, the transistor shown in Figure 3.12 is not conducting. Current threshold comparator mode: 0 The Current Threshold Comparator Mode is disabled. 1 adcCtcv is decremented when the absolute current value is below the threshold and incremented otherwise. 2 adcCtcv is reset when the absolute current value is below the threshold and incremented otherwise. 3 adcCtcv retains its value when the absolute current value is below the threshold and incremented otherwise. If set to 1, enables the strobe to interrupt the controller when the current accumulator exceeds its threshold. If set to 1, enables the strobes to interrupt the controller when an over-range or overflow has been detected in the current channel. If set to 1, enables the strobes to interrupt the controller when an over-range or overflow has been detected in the voltage/temperature channel. If set to 1, then adcCtcv is reset when the current result counter is reset (adcCrcv). If set to 1, then adcCaccu is reset when the current result counter is reset (adcCrcv). If set to 1, enables the strobe to interrupt the controller for the voltage threshold comparator and voltage accumulator functionality. If set to 0, the absolute value of the single voltage conversion result is compared to the threshold adcVTh. If set to 1, the accumulated results of all voltage conversions within an MRCS are compared to the threshold adcVTh. If set to 1, enables the strobe to interrupt the controller for checking the temperature limits. Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 85 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.3.31 Register “adcGomd” – Reference Voltage and SDM Configuration Table 3.55 Register adcGomd Name Address vrefSel Bits Default Access 00BIN RW [1:0] sdmChopClkDiv [3:2] 00BIN RW [7:4] 0001BIN RW 50HEX sdmSetup Description Selection of the voltage reference: 0 vbgh (high precision bandgap) 1 vbgl (low power bandgap) 2 vcm (common mode voltage) 3 External reference voltage Clock divider value for the chop clock related to the SDM clock. See equation (5) in section 3.8.1.1 for the FP State and equation (8) in section 3.8.1.2 for the LP/ULP State. Configuration of the initial setup procedure: 0 Execute 4 SDM clock cycles 1 Execute 8 SDM clock cycles … 7 Execute 512 SDM clock cycles 8-15 Execute 1024 SDM clock cycles 3.8.3.32 Register “adcSamp” – Oversampling and Filter Configuration Table 3.56 Register adcSamp Bits Default Access osr Name [1:0] 00BIN RW Unused avgFiltCfg [2] [4:3] 0BIN 00BIN RO RW [5] 0BIN RW [7:6] 00BIN RO chopPause Unused Data Sheet July 10, 2014 Address 51HEX Description Oversampling rate: 0 256x oversampling 1 128x oversampling 2 64x oversampling 3 32x oversampling Unused; always write as 0. Configuration of post filter (averaging filter) : 0-1 No averaging 2 2-stage averaging filter 3 3-stage averaging filter Length of pause in chopping mode: 0 8 SDM clock cycles 1 16 SDM clock cycles Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 86 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.4 ADC Control and Conversion Timing In the FP State, the ADC unit is running with the 4MHz clock derived from the HP oscillator. Its operation can be fully controlled by the external microcontroller via register settings. In the LP or ULP State, the ADC unit is running with the 125 kHz clock from the LP oscillator. Basic configurations for the ADC unit are taken from the register file; however, its operation is fully controlled by the PMU. 3.8.4.1 ADC Operation in the FP State Before any of the ADCs can be used in the FP State, they must be powered up by setting the pwrAdcI bit for the current ADC and/or the pwrAdcV bit for the voltage/temperature ADC in the pwrCfgFp register to 1 (see Table 3.18). These bits can be kept set to 1 when entering one of the power-down states as the PMU takes over the control of the power signals. The user can select which kind of operation will be performed by the ADCs and can control the input multiplexers shown in Figure 3.12 by setting the field adcMode in the adcCtrl register appropriately (see Table 3.58). The following settings are possible: Table 3.57 adcMode Settings adcMode 0 1 2 3 4 5 6 7 1) Current ADC Configuration Voltage / Temperature ADC Configuration Current INP/INN Current INP/INN Current INP/INN Voltage Divided VBAT/VSSA External temperature VDDA/NTH and NTH/NTL Internal temperature VPTAT/VREF Offset Calibration Mode; shortened inputs VCM/VCM VCM/VCM Gain Calibration Mode @ maximum (positive) input 1) VREF / VSSA VREF/VSSA Gain Calibration Mode @ minimum (negative) input 1) VSSA / VREF VSSA / VREF 1 mV internal test voltage Voltage 1 mV/VSSA Divided VBAT/VSSA Test Mode; each multiplexer is individually controlled by the following: cSel field in adcChan register (Table 3.59) vtSel field in adcChan register The two gain calibration modes cause an ADC over-range error in the current ADC as the minimum gain of PGA2 is 4. Therefore these modes are not usable for the current ADC. After setting the desired mode of operation, the user must start the conversion by setting the startAdcC bit in the adcCtrl register (see Table 3.58) for the current channel and/or the startAdcV bit for the voltage/ temperature channel to 1. After an initial setup phase, measurement results are stored in the corresponding result registers. By controlling the startAdc bits, the user is able to generate an individual conversion sequence (ADC operation stops after one conversion sequence has finished) or continuous conversion (ADC operation continues after one conversion sequence has finished). Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 87 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) A conversion sequence is defined as a series of several measurements. The number of measurements to be performed is controlled by the result counter functionality, so it is possible to have multiple measurements per conversion sequence (MRCS) or just a single measurement (SRCS). At the end of one conversion sequence, the “set interrupt” strobe for the corresponding conversion interrupt ready status bit (irqStat[7:5]) is generated. Although this strobe is only generated after the last measurement within an MRCS, each measurement in the MRCS is used for accumulation and minimum/maximum determination. Note: The MRCS functionality is only available for current and voltage measurements, not for temperature measurements. To perform an individual conversion sequence for a SRCS or MRCS, the user must generate a strobe signal on the corresponding startAdc bit by setting the startAdc bit to 1 (rising edge) first and then to 0 (falling edge). The rising edge of startAdc signals the ADC to start the conversion. On this start signal, the corresponding adcActive flag is set to 1, which can be read from bits 4 and 5 in the SSW (see section 3.1.1). When the conversion sequence has finished, the corresponding ready signal is generated. At that time, the internal logic evaluates the status of the startAdc bit again. If it was cleared already as required for an individual conversion sequence, the ADC stops its operation and clears the adcActive flag. This behavior is shown in Figure 3.22 and Figure 3.23. Figure 3.22 Individual SRCS startAdc adcActive ready result a Setup Time and Single Measurement Note that the ADC stops since startAdc is low at the end of the conversion sequence for the individual SRCS. Figure 3.23 Individual MRCS (Example for Result Counter of 3) startAdc adcActive ready result a Setup Time and Single Measurement b c Single Measurement Note that the ADC stops since startAdc is low at the end of the conversion sequence for an individual MRCS. Important: The ready strobe shown in Figure 3.22 and Figure 3.23 is used to set the interrupt status bit, but the interrupt status bit remains set until it is cleared by the user’s software. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 88 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) To perform a continuous conversion sequence for SRCS or MRCS, the user must set the corresponding startAdc bit to 1 (rising edge). The rising edge of startAdc signals the ADC to start the conversion. On this start signal, the corresponding adcActive flag is set to 1, which can be read from bits 4 and 5 in the SSW. When one conversion sequence has finished, the corresponding ready signal is generated. At that time, the internal logic evaluates the status of the startAdc bit again. As the startAdc bit is still 1, the ADC continues its operation but without the need for the setup time. This behavior is shown in Figure 3.24 and Figure 3.25. Figure 3.24 Continuous SRCS startAdc adcActive ready result a Setup Time and Single Measurement b c d Single Measurement Note that the ADC continues since startAdc is high at the end of the conversion sequence for a continuous SRCS. Figure 3.25 Continuous MRCS (Example for Result Counter of 3) startAdc adcActive ready result a Setup Time and Single Measurement b c d e f g Single Measurement Note that the ADC continues since startAdc is high at the end of the conversion sequence for a continuous MRCS. When a continuous conversion sequence is performed that will be stopped after the present active conversion sequence has completed, the user only needs to clear the startAdc bit of the channel that will be stopped. Then the user can either wait for the next interrupt, which will be set by the last ready strobe, or check the corresponding adcActive bit in the SSW. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 89 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.26 Stopping Continuous SRCS startAdc adcActive ready result d e f g h i j Single Measurement Note that the ADC stops since startAdc is low at the end of the conversion sequence for a continuous SRCS. When a conversion sequence is performed that will be interrupted (stopped immediately), the user must clear the startAdc bit of the channel that will be stopped (when set) and must set the stopAdc bit in the adcCtrl register to 1. In the ADC unit, the stopAdc bit is only evaluated when the startAdc bit of a channel is low and the corresponding adcActive bit is high. Figure 3.27 Stopping Continuous MRCS (Example for Result Counter of 3) startAdc adcActive ready result b c d e f g h i Single Measurement Note that the ADC stops since startAdc is low at the end of the conversion sequence for a continuous MRCS; otherwise the stopAdc bit is ignored. Therefore there is only one stopAdc bit that is used for both channels. This allows the user to stop both channels by clearing both startAdc bits when setting the stopAdc bit or to stop only one channel by keeping one startAdc bit high. The signal behavior for interrupting a channel is shown in Figure 3.28 and Figure 3.29. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 90 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.28 Interrupting a Continuous SRCS startAdc stopAdc adcActive ready result d e f g h i Single Measurement Note that the ADC immediately stops since startAdc is low and stopAdc is high. Figure 3.29 Interrupting a Continuous MRCS (Example for Result Counter of 3) startAdc stopAdc adcActive ready result b c d e f g Single Measurement Note that the ADC immediately stops since startAdc is low and stopAdc is high. Important: The stopAdc bit is only evaluated when startAdc bit is low. Note: The interrupt sequence shown in Figure 3.28 and Figure 3.29 is also performed by the PMU on transition from the FP State to any power-down state as well as on transition from any power-down state to the FP State. This allows the user to keep the startAdc bits set on transition to any power-down state. After wake-up, the ADCs continue the operation they performed before going to power-down. Most of the register settings that influence both ADC channels (e.g., oversampling rate) can only be changed when both ADC channels are inactive. As explained above, this is not true for the stopAdc bit. The adcMode field can also be changed while any ADC channel is active. This is useful for continuing with current measurements in the first ADC channel while changing the second ADC channel from voltage to temperature measurements (as an example). On the rising edge of its startAdc bit, each ADC channel stores internally the mode it is configured for and keeps this setting until the next rising edge of its startAdc bit. When one channel is reconfigured while the other one is active, this channel does not start immediately after being re-enabled but synchronizes to the active channel so that the results are generated at the same time. See Figure 3.30. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 91 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.30 Signal Behavior of adcMode adcMode (Reg) 2 0 startAdcC 0 adcMode(Adc1) adcActive1 ready1 SetupTime + 1 Meas 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 result1 startAdcV 0 adcMode(Adc2) 2 adcActive2 ready2 result2 Data Sheet July 10, 2014 Sync + Setup Time + 1 Meas Setup Time + 1 Meas 1 2 3 4 5 0 1 2 3 4 5 6 7 8 9 0 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 92 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.4.2 Register “adcCtrl” – ADC Control Register Table 3.58 Register adcCtrl Name Address Bits Default Access startAdcC [0] 0BIN RW startAdcV [1] 0BIN RW stopAdc [2] 0BIN RW adcMode [5:3] 000BIN RW [6] [7] 0BIN 0BIN RW RO 56HEX chopEna Unused 3.8.4.3 Description Start signal for the current ADC; used in the FP State, ignored in other states. Start signal for the voltage/temperature ADC; used in the FP State, ignored in other states. Stop signal for both ADCs; used in the FP State, ignored in other states. ADC multiplexer configuration; used in the FP State, ignored in other states; for settings 0, 1, 2, and 6, the first value is applied to the current ADC, the second to the voltage/temperature ADC. (See section 3.8.4.1 for more details.) 0 Measure current and voltage 1 Measure current and external temperature 2 Measure current and internal temperature 3 Offset calibration 4 Gain calibration @ maximum (positive) input 5 Gain calibration @ minimum (negative) input 6 Internal test voltage and voltage 7 Test Mode (control multiplexer via the adcChan register’s cSel and vtSel fields) If set to 1, Chopping Mode is enabled. Unused; always write as 0. ADC Operation in LP/ULP State During the LP or ULP State, the ADCs are fully controlled by the PMU depending on the settings of register pwrCfgLp (see Table 3.19). The PMU overrides the settings of the startAdc bits, the stopAdc bit, and adcMode field. The settings of pwrAdcI and pwrAdcV are also ignored until the system wakes up. While no further settings are required for the continuous measurement set-ups, the user can independently configure how many current and/or voltage measurements happen within a single measurement window. For current (the green and orange boxes In Figure 3.6 to Figure 3.9), the number of current measurements in each window is configured by the setting of adcCrcl (see Table 3.37). For voltage (the orange boxes shown in Figure 3.6 to Figure 3.9), the number of voltage measurements in each window is configured by the setting of adcVrcl (see Table 3.39).There is always only one temperature measurement as the last measurement made by the voltage/temperature ADC in a sample period. Important: If an interrupt wakes up the system before the end of a measurement window, the conversion sequence is interrupted and less than the configured number of measurements will have been completed. This can be checked by the registers adcCrcv (see Table 3.38) and adcVrcv (see Table 3.40). Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 93 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.4.4 ADC Conversion Timing The complete conversion process is controlled by an internal state machine that guarantees that only valid measurement results are used. The base for all ADC timings is the SDM clock, which is generated from the 4MHz clock in FP State or from the 125kHz clock in LP and ULP State. After the ADC measurement has been started (rising edge of startAdc), the state machine always introduces a configurable number of SDM clock cycles (field sdmSetup in register adcGomd; see Table 3.55) to allow the analog part of the SDM to settle. After 4 this delay, the incoming bit streams are used to fill the sinc decimation filter. This lasts 4 times the sample rate, which is configured by the oversampling rate (the osr field in register adcSamp; see Table 3.56). Then the first valid result value comes from the decimation filter. Figure 3.31 Timing for Current, Voltage, and Internal Temperature Measurements without Chopping for Different Configurations of the Average Filter sdmSetup startAdc Sample Rate tS Time to Fill Filter: 4 * tS Conversion Result (no avg) M(tN) M(tN+1) M(tN+2) M(tN+3) M(tN+4) M(tN+5) M(tN) M(tN+1) M(tN+2) M(tN+3) M(tN+4) M(tN) M(tN+1) M(tN+2) M(tN+3) ready (no avg) Time to Fill Filter: 5 * tS Conversion Result (2x avg) ready (2x avg) Time to Fill Filter: 6 * tS Conversion Result (3x avg) ready (3x avg) M = measurement; t = time. For current, voltage, or internal temperature measurement without chopping, when only one input source must be measured, this is the first valid value. The time when the first valid result is present also depends on the configuration of the average filter (the avgFiltCfg field in register adcSamp). If no averaging is used, the first valid value is also the first valid result stored in adcCdat, adcVdat, or adcTdat. For the 2-stage or 3-stage average filter, respectively, two or three valid values are needed to calculate a valid result. This adds an additional delay, respectively, of 1 or 2 times the sample rate. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 94 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) For external temperature measurement without chopping, two input sources must be measured: the voltage drop over the reference resistor (the result is stored in register adcRdat) and the voltage drop over the NTC resistor (result stored in register adcTdat). The sdmSetup time is only introduced at the beginning of the conversion sequence (the rising edge of startAdc). Each single measurement of one of the two values needs 4 times the sample rate when averaging is disabled, or respectively, 5 or 6 times the sample rate when using the 2-stage or 3-stage average filter. This also means that a complete pair of values used to calculate one external temperature 4 value needs 8 (10 or 12 for averaging) times the sample rate because for each value, the pipeline of the sinc decimation filter must be filled first. Figure 3.32 Timing for External Temperature Measurements without Chopping when No Average Filter is Enabled sdmSetup startAdc ref_not_ntc conversion result (no avg) adcTdat MNTC(tN) adcRdat MNTC(tN+1) MREF(tN) MNTC(tN+2) MREF(tN+1) MREF(tN+2) ready (no avg) M = measurement; t = time. Note that using an average filter will lead, respectively, to 5 and 6 conversion results during each high and low phase of ref_not_ntc. The timings shown in the previous two figures are without chopping, which means that the differential input signal is always applied in the same manner to the analog SD-ADC. Although this kind of measurement is fast (one result value after each sample time), it has the drawback that it also converts any offset present in the analog blocks. This would lead to less accurate measurement results. To overcome this, chopping can be enabled (bit chopEna in register adcCtrl; see Table 3.58). When chopping is enabled, the differential input signal is directly applied to the analog SD-ADC the first time and inverted the second time. Taking this into account in the digital part removes the offset applied by the ADC itself: ( offset) (-1) ( - Vin offset) data Vin Vin 2 Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. (15) 95 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) For current, voltage, or internal temperature measurement with Chopping Mode enabled (chopEna set to 1), this leads to a timing similar to the external temperature measurement without chopping and averaging since two values are measured: the normal input and the inverted input. Each single measurement of one of the two values needs 4 times the sample rate as no averaging of the single measurement is performed. Instead, the average filter is automatically configured as a 2-stage average filter to calculate the formula above. The second difference is that a small pause (chopping pause) is introduced each time the chop control signal changes to allow the analog blocks to settle due to the input change. This is possible since the chopEna bit influences both ADC paths. The length of the chop pause is either 8 or 16 SDM clock cycles, which can be configured using the chopPause bit in register adcSamp. Figure 3.33 Timing for Current, Voltage, and Internal Temperature Measurements using Chopping Example shown is for current measurement: sdmSetup startAdc chopPause chopPause chop ctrl Conversion Result (chop) M+ adcCdat MMCHP(tN) = 0.5*(M+-M-) M+ MCHP(tN+1) = -0.5*(M--M+) MMCHP(tN+2) = 0.5*(M+-M-) M+ M- MCHP(tN+3) = -0.5*(M--M+) ready (chop) M = measurement; t = time. For external temperature measurement using chopping, two different input sources must be measured twice, non-inverted and inverted, which leads to four values to be measured to determine a result. To keep both ADC paths aligned, the chopPause is introduced for each measured value. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 96 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.34 Timing for External Temperature Measurements using Chopping sdmSetup startAdc ref_not_ntc chop ctrl chopPause Conversion Result (chop) M+NTC adcTdat M-NTC M+REF M-REF M+NTC M-NTC 0.5*(M+NTC(tN) - M-NTC(tN)) adcRdat M+REF M-REF 0.5*(M+NTC(tN+1) - M-NTC(tN+1)) 0.5*(M+REF(tN) - M-REF(tN)) ready (chop) M = measurement; t = time. Important: The timings only show the principle. Additional small delays such as pipeline delays are not included. 3.8.5 Diagnostic Features 3.8.5.1 ADC Analog Multiplexer Control for Diagnosis and Test In the FP State, the three multiplexers shown in Figure 3.12 can be directly controlled via the register adcChan (see Table 3.59) when the adcMode field in register adcCtrl is set to 7 (see Table 3.58). For other settings of adcMode, the settings of register adcChan are ignored and both multiplexers for input selection are controlled either by the adcMode field in the FP State or by the PMU in LP or ULP State. The vtSel field in register adcChan is used to select the input sources of the voltage/temperature ADC. The cSel field in register adcChan is used to select the input sources of the current ADC. Important: the reference voltage (non-inverted as well as inverted) cannot be measured by the current ADC as the minimum gain of PGA-2 is 4, which causes an ADC over-range error. For some settings of adcMode, cSel, and vtSel, the reference voltage is applied to the ADCs. The user can select the source of the reference voltage with the vrefSel field in register adcGomd (see Table 3.55). As can be seen from Figure 3.12, the user’s software can connect internal current sources to the input wires of the INP and INN pins as well as to the input wires of the NTH and NTL pins. To enable the different current sources for the four input wires, the corresponding enable bit in register currentSrcEna must be set to 1 (see Table 3.62). Important Warning: Do not enable both current sources on the same input at the same time. Important: The current sources can be enabled independent of the adcMode. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 97 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Register “adcChan” – Analog Multiplexer Configuration 3.8.5.2 Table 3.59 Register adcChan Name Address vtSel cSel D0HEX Bits Default Access [2:0] 000BIN RW [5:3] 000BIN RW Description When adcMode == 7, this field selects the differential sources for the voltage/temperature ADC: vtSel inp inn 000BIN 001BIN 010BIN 011BIN 100BIN 101BIN 110BIN 111BIN VDDA NTL VPTAT VBATP VBGH (i.e., VREF) VBGL (i.e., VREFLP) VCM High impedance NTH NTH VBGH (i.e., VREF) VBATN VSSA VSSA VCM High impedance When adcMode == 7, this field selects the differential sources for the current ADC: 000BIN 001BIN 010BIN 011BIN 100BIN 101BIN 110BIN 111BIN Unused Unused 3.8.6 [6] [7] 0BIN 0BIN RW RW INP INP INP INP 1 mV Unused Unused VCM INN INN INN INN VSSA VCM Unused; always write as 0. Unused; always write as 0. Digital Features 3.8.6.1 Built-in Self-Test (BIST) The digital ADC BIST feature allows the user to test the digital logic of the ADC data path. The BIST feature is enabled by setting the bistEna bit in register adcDiag to 1 (see Table 3.61). When the BIST feature is enabled, the same programmable bit stream is applied to both inputs of the decimation filter instead of the outputs from the noise cancellation filters. The ADCs must also be set into operation as during normal operation. The bit stream to be applied to the decimation filter is programmed to the lower 30 bits of register adcCaccTh (see Table 3.44). These 30 bits function as a shift-rotate register as shown in Figure 3.35, and the output of the lowest bit is used as the bit stream for the BIST. Important: Since register adcCaccTh is used for the BIST, the current accumulator threshold functionality cannot be used. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 98 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 3.35 Usage of Register adcCaccTh for the Digital ADC BIST X X 1 0 1 0 29 28 27 26 ... 1 0 1 0 3 2 1 0 Bitstream for BIST Table 3.60 shows four example bit streams as well as the expected output stored in the corresponding data registers adcCdat, adcVdat, adcTdat, and/or adcRdat if enabled. In these examples, the offset correction value (e.g., register adcCoff) is set to 0, the gain correction value (e.g., register adcCgan) is set to 1.0, and the post correction gain factor (e.g., bit field curPoCoGain [1:0] in register adcPoCoGain) is set to gain factor 1 (bit field set to 00BIN) and then to gain factor 2 (bit field set to 01BIN). Table 3.60 Example Results of BIST 1/0 Bit Ratio 1/6 5/6 2/5 3/5 Bit Stream 100000_100000_100000_100000_100000 20820820HEX 111110_111110_111110_111110_111110 3EFBEFBEHEX 10010_10010_10010_10010_10010_10010 25294A52HEX 10110_10110_10110_10110_10110_10110 2D6B5AD6HEX 3.8.6.2 Result Data (xPoCoGain = Gain Factor 1, Bit Field = 00BIN) Result Data (xPoCoGain = Gain Factor 2, Bit Field = 01BIN) 555555HEX 800000HEX (negative over-range) 7FFFFFHEX (positive over-range) E66666HEX CCCCCCHEX 199999HEX 333332HEX AAAAAAHEX Decimation Filter Output Test The decimation filter output test allows the user to observe the outputs of both decimation filters. This feature is enabled by setting bit rawEna in register adcDiag to 1. When this feature is enabled, the 32-bit output value of the decimation filter for the current ADC is stored in registers adcCmax (MSBs; see Table 3.48) and adcCmin (LSBs; see Table 3.49) and the 32-bit output value of the decimation filter for the voltage/temperature ADC is stored in registers adcVmax (MSBs; see Table 3.50) and adcVmin (LSBs; see Table 3.51). The ADCs must also be set into operation as during normal operation. Note: When this feature is enabled, all normal ADC operations described in the previous sections function as described except the minimum and maximum functionality for the current and voltage values because the registers are used for this test function. Note: This feature can be combined with the digital ADC BIST feature. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 99 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.8.6.3 ADC Interface Test nd rd The ADC interface test allows the user to observe the incoming 2 and 3 order bit streams from both analog parts of the SD-ADCs. This feature is enabled by setting bit adcIfTestEna in register adcDiag to 1. The digital part of the ADC unit must be enabled as for normal operation as it generates the correct sample strobe for the test logic. This function is only available in the FP State as it runs on the 20MHz clock from the high-precision oscillator. All sampled values (4 bits) are shifted out of the STO pad. To enable the user to synchronize on the sampled data, a 1 and a 0 are shifted out before each 4-bit value as shown in Figure 3.36. Figure 3.36 Bit Stream of ADC Interface Test at STO Pad 2nd I 3rd I 2nd V 3rd V Note: This feature can be combined with the digital ADC BIST feature and with the decimation filter output test. 3.8.6.4 Register “adcDiag” – Enable Register for Test and Diagnosis Features Table 3.61 Register adcDiag Name Address bistEna rawEna adcIfTestEna Unused stopClkChop D1HEX clkChopEna 3.8.6.5 Bits Default Access [0] [1] 0BIN 0BIN RW RW [2] [5:3] [6] 0BIN 000BIN 0BIN RW RW RW [7] 1BIN RW Description If set to 1, enables BIST. If set to 1, enables the decimation filter output test (ADC raw data test). If set to 1, enables the serial ADC test. Unused; always write as 0. Disable signal for the global chopper (overall analog and digital part chopping). Keep this bit ‘0’ in application if chopping is required. Enable signal for internal chopper of the sigma-delta modulator input stage. Keep this bit ‘0’ in application. Register “currentSrcEna” – Enable Register for Current Source Table 3.62 Register currentSrcEna Name Bits Default Access [0] [1] [2] [3] [4] 0BIN 0BIN 0BIN 0BIN 0BIN RW RW RW RW RW Enable 50µA current source to INP. Unused; always write as 0. Enable 50µA current source to INN. Unused; always write as 0. Enable 50µA current source on NTH. psinkEnVbat [5] 0BIN RW Enable -50µA current source on NTH. nsrcEnVbat [6] 0BIN RW Enable 50µA current source on NTL. nsinkEnVbat [7] 0BIN RW Enable -50µA current source on NTL. inampInpSrcEna Unused inampInnSrcEna Unused psrcEnVbat Data Sheet July 10, 2014 Address D2HEX Description © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 100 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.9 SBC LIN Support Logic (for ZSSC1750 only) The ZSSC1750 LIN support logic handles two error conditions: a LIN dominant timeout on the TXD pin and a short to VBAT on the LIN pin. Figure 3.37 illustrates the error protection logic discussed in the next sections. Figure 3.37 Protection Logic of the LIN TXD Line detLinShort detTxdTimeout FP state (PMU) txdProtDis (register file) TXD (from external MCU) 3.9.1 O R & O R LIN-TXD (LIN-PHY) LIN Wakeup Detection A LIN master generates a LIN wakeup frame by driving a dominant value of 0 of at least 250μs on the LIN bus. The standard requires that a LIN slave must recognize a LIN wakeup when the LIN bus is low for more than 150μs. There is a 6-bit counter running with the 125kHz LP clock implemented in the ZSSC1750 to support the LIN wakeup detection. When the function is disabled (irqEn[4] is set to 0), the counter is set to 20HEX and no interrupt can occur. When the function is enabled (irqEn[4] is set to 1), the LIN RXD line is observed. When the LIN RXD line is high, the counter is set to 00HEX. When the LIN RXD line becomes low, the counter is incremented in each clock cycle until it reaches the value 20 HEX where it stops incrementing. When the counter is equal to the programmed wakeup delay (register linWuDelay; see Table 3.66), a set strobe for the corresponding interrupt is generated, which causes the system to wake up. The register linWuDelay has a default value of 14HEX. This setting guarantees that no low level less than 150μs on the LIN RXD line causes a wakeup due to the inaccuracy of the LP oscillator. 3.9.2 TXD Timeout Detection The digital LIN controller in the external microcontroller must ensure that it does not completely block the LIN bus due to continuously transmitting a dominant value of 0. As it is still possible that the TXD line from the external microcontroller is stuck at 0 due to a software or hardware error in the external microcontroller or a broken connection between the external microcontroller and the ZSSC1750, the LIN support logic observes the TXD line in FP State to detect if the TXD line is erroneously low. The timeout detection circuit can handle baud rates down to 1kBaud, where the maximum time that a digital LIN controller (slave device!) can transmit a low level is 9ms (start bit and 8 data bits). To overcome inaccuracies of the internal clocks, the internal logic and untrimmed LIN nodes, the timeout value is 10.24ms. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 101 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) On detection of a TXD timeout, an internal flag (detTxdTimeout in Figure 3.37) is set to the high level, which forces the LIN TXD line to 1, and the corresponding interrupt status (irqStat[2]) is set. While the interrupt status bit is cleared on read access to the interrupt status register, the internal flag remains high, also keeping LIN TXD at the high level. The status of the internal flag is mirrored in SSW[2]. To clear this internal flag and to be able to transmit again via the LIN bus, a value of 1 must be written to bit clrTxdTimeout in register linCfg (see Table 3.64). 3.9.3 LIN Short Detection The LIN PHY contains a function to detect a short to VBAT on the LIN bus by sensing the current through the open-drain output transistor in the LIN PHY. When the current is too high, the LIN PHY drives the SHORT signal going to the digital block to the high level (see Figure 3.38). Under normal circumstances, the LIN PHY signals a short only if a dominant value of 0 will be transmitted, but the bus remains at its recessive high level. However, high current consumption is also possible due to EMC events. To increase the safety of the system and to avoid misinterpretation, the incoming SHORT signal is gated and filtered. First, the SHORT signal from the LIN PHY is driven through a configurable gating block inside the digital block. The gating block is configured using register linShortDelay (see Table 3.65). If register linShortDelay is set to a value not equal to 0, the TXD line going to and the RXD line coming from the LIN PHY are observed. When the TXD line becomes low while the RXD line remains high, the gating block waits for linShortDelay times 4MHz clock cycles before opening the gate. The gate is closed when either TXD becomes high again or RXD becomes low (see Figure 3.38). This feature is used to evaluate the SHORT signal only when a dominant value of 0 is transmitted, but the bus remains at its recessive high level as well as to eliminate the delay from the TXD line through the LIN PHY back to the RXD line. Figure 3.38 Waveform Showing the Gating Principle for Non-zero Values of linShortDelay TXD RXD en gate linShortDelay x 250ns gated SHORT When the register linShortDelay is set to 0, the gate for the SHORT signal is always open. This means that the SHORT signal is always passed through the gating block even when the TXD line is high or the RXD line is low. The gated SHORT signal is applied to a configurable de-bouncing filter. This de-bouncing filter is configured using register linShortFilter (see Table 3.64), and it monitors the gated SHORT signal using the internal 4MHz clock. When the gated SHORT signal is continuously high for (linShortFilter + 1) clock cycles, the LIN short interrupt status bit (irqStat[3]) is set, enabling the user’s software running on the connected external microcontroller to respond to this situation. The interrupt status bit is cleared on read access to the interrupt status register. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 102 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) The software can also enable the hardware to protect the TXD line in the case of a detected short condition. When the shortProtEna bit in register linCfg (see Table 3.63) is set to 1 and a short condition is detected by the de-bouncing filter, an internal flag (detLinShort in Figure 3.37) is set to the high level, which forces the LIN TXD line high. The status of the internal flag is mirrored in SSW[3]. The internal flag remains high until it is explicitly cleared by the software by writing a value of 1 to the clrLinShort bit in register linCfg. 3.9.4 LIN Testing The LIN TXD line protection features (TXD timeout, LIN short, LP State) might restrict the possibility of testing the LIN PHY. Therefore the protection can be disabled by setting the txdProtDis bit in register linCfg to 1 (see Figure 3.37). Important Warning: This must never be done during normal operation. The IC will not be damaged, but communication errors will not be detected. 3.9.4.1 Register “linCfg” – LIN Configuration Register (ZSSC1750 Only) Table 3.63 ZSSC1750 Register linCfg Important: For the ZSSC1751 this register is not used and must remain as the default setting. Name Bits Default Access linFastEna [0] 0BIN RW txdProtDis [1] 0BIN RW [2] [3] [4] 0BIN 0BIN 0BIN RW RO RWS [5] 0BIN RWS [7:6] 00BIN RO shortProtEna Unused clrTxdTimeout clrLinShort Unused Data Sheet July 10, 2014 Address B4HEX Description When set to 1, the slew rate control in the LIN PHY transmitter is disabled allowing higher LIN data rates of up to 125kBaud (non-standard feature). When set to 1, all protection features that force the LIN TXD line to 1 are overwritten (for test purposes only). If set to 1, enables the LIN short protection. Unused; always write as 0. Strobe register; write 1 to clear the detected TXD timeout flag and to release the protection of the LIN TXD line. Strobe register; write 1 to clear the detected LIN SHORT flag and to release the protection of the LIN TXD line. Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 103 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.9.4.2 Register “linShortFilter” Configuration for the LIN Short De-bounce Filter (ZSSC1750 Only) Table 3.64 ZSSC1750 Register linShortFilter Important: For the ZSSC1751 this register is not used and must remain as the default setting. Name linShortFilter 3.9.4.3 Address Bits Default Access B5HEX [7:0] 0FHEX RW Description Filter configuration for the LIN short detector. This register defines the number of 4MHz clock cycles (linShortFilter + 1) where the gated LIN SHORT signal in the LIN PHY must be high to detect a SHORT condition on the LIN bus. Register “linShortDelay” –Configuration Register LIN Short TX-RX Delay (ZSSC1750 Only) Table 3.65 ZSSC1750 Register linShortDelay Important: For the ZSSC1751 this register is not used and must remain as the default setting. Name linShortDelay Address Bits Default Access B6HEX [7:0] 4FHEX RW Description Delay configuration for gating the LIN SHORT signal. This register defines the number of 4MHz clock cycles where TXD is low and RXD is high before the gating logic of the LIN SHORT signal from the LIN PHY is removed. When RXD becomes low or TXD becomes high, the gating logic is reactivated. Note: When linShortDelay is set to 0, the TXD and RXD levels are ignored and the LIN SHORT signal is not gated. 3.9.4.4 Register “linWuDelay” – Configuration Register for LIN Wakeup Time (ZSSC1750 Only) Table 3.66 ZSSC1750 Register linWuDelay Important: For the ZSSC1751 this register is not used and must remain as the default setting. Name Address linWuDelay Bits Default Access [4:0] 10100BIN RW LIN wakeup time. This register defines the number of 125 kHz clock cycles where LIN-RXD must be low before a LIN wakeup conditions is detected. Important Warning: Do not set to 0. [7:5] 000BIN RO Unused; always write as 0 B7HEX Unused Data Sheet July 10, 2014 Description © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 104 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.10 ZSSC1750/51 OTP (CONFIG REGISTER) The ZSSC1750/51 has an integrated 32x8 bit one-time programmable (OTP) memory that contains the required trimming data as well as the traceability information. The default (erased) state of the OTP cells is 0. Because some of the programmed trim bits are critical for operation, such as the voltage trim bits, redundancy is implemented for the lower quarter of the OTP memory. This part of the OTP contains only up to four bits of information that are programmed to bits [3:0] as well as to bits [7:4]. During the download procedure, the correct content is determined by combining bit 0 and bit 4, bit 1 and bit 5, bit 2 and bit 6, and bit 3 and bit 7 via an OR gate. Table 3.67 OTP Memory Map Name OTP SPI Address Address Bit Range Copy to Reg. Redundancy Byte Order Description OTP_VALID LIN_TRIM VDD_TRIM 00HEX 01HEX 02HEX E0HEX E1HEX E2HEX 0 3:0 3:0 No Yes Yes Yes Yes Yes BG_TRIM IREF_OSC_0 IREF_OSC_1 03HEX 04HEX 05HEX E3HEX E4HEX E5HEX 3:0 3:0 3:0 Yes Yes Yes Yes Yes Yes IREF_OSC_2 IREF_OSC_3 IREF_LP_OSC ADCCGAN_0 ADCCGAN_1 ADCCGAN_2 ADCCOFF_0 ADCCOFF_1 ADCCOFF_2 ADCVGAN_0 ADCVGAN_1 ADCVGAN_2 ADCVOFF_0 ADCVOFF_1 ADCVOFF_2 ADCTGAN_0 ADCTGAN_1 06HEX 07HEX 08HEX 09HEX 0AHEX 0BHEX 0CHEX 0DHEX 0EHEX 0FHEX 10HEX 11HEX 12HEX 13HEX 14HEX 15HEX 16HEX E6HEX E7HEX E8HEX E9HEX EAHEX EBHEX ECHEX EDHEX EEHEX EFHEX F0HEX F1HEX F2HEX F3HEX F4HEX F5HEX F6HEX 3:0 3:0 6:0 7:0 7:0 7:0 7:0 7:0 7:0 7:0 7:0 7:0 7:0 7:0 7:0 7:0 7:0 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No No No No No No No No [0]: OTP content valid [3:0]: IBIAS_LIN_TRIM[3:0] [0]: VDDC trim bit [1]: VDDP trim bit [3:2]: vbgh_trim[1:0] --- [3:0]: vbgh_trim[5:2] LSB [3:0]: IREF_OSC_TC_TRIM[3:0] MSB [0]: IREF_OSC_TC_TRIM[4] LSB [2]: IBIAS_LIN_TRIM[4] [3]: IREF_OSC_TRIM[0] --- [3:0]: IREF_OSC_TRIM[4:1] MSB [3:0]: IREF_OSC_TRIM[8:5] --- Trim value for the low-power oscillator LSB --- Gain for the current measurement MSB LSB --- Offset for the current measurement MSB LSB --- Gain for the voltage measurement MSB LSB --- Offset for the voltage measurement MSB LSB Gain for the temperature MSB measurement ADCTOFF_0 ADCTOFF_1 17HEX 18HEX F7HEX F8HEX 7:0 7:0 Yes Yes No No LSB Offset for the temperature MSB measurement --- 19HEX F9HEX --- No No Data Sheet July 10, 2014 ------- --- Unused © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 105 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Name LOT_ID_0 LOT_ID_1 WAFER_NO_0 WAFER_NO_1 DIE_POS_0 DIE_POS_1 OTP SPI Address Address 1AHEX 1BHEX 1CHEX 1DHEX 1EHEX 1FHEX FAHEX FBHEX FCHEX FDHEX FEHEX FFHEX Bit Range 7:0 7:0 7:0 7:0 7:0 7:0 Copy to Reg. No No No No No No Redundancy No No No No No No Byte Order Description LSB Lot ID number MSB LSB Wafer number MSB LSB Die position MSB After reset of the SBC, the OTP download procedure is automatically triggered. First, the OTP contents are checked for validity (“bit 0 OR bit 4” must be equal to 1). If the content is not valid, the download procedure is stopped. Otherwise, the information stored at OTP addresses 1 to 18HEX is copied into the corresponding registers. The download procedure can also be started by the user by writing the value 1 into the otpDownload bit in register cmdExe (see Table 3.7). Special care must be taken after starting the OTP download procedure as the system must not go to the power-down state as long as the download procedure is active. The status of the download procedure is signaled to the user via the SSW bit 0: the OTP download procedure is active when SSW[0] = 1. In addition to being read by triggering the OTP download procedure that copies the OTP contents into the corresponding registers, the raw contents of the OTP can be read by the user via the SPI interface at SPI addresses E0HEX to FFHEX. This might be useful for checking the contents of the OTP. For the lowest quarter of the OTP, this is useful for checking that no bit has changed its value. The user might also choose to implement redundancy for the other values by mirroring the contents into the nonvolatile memory on the external microcontroller. 3.11 Miscellaneous Registers 3.11.1.1 Register “pullResEna” – Pull-down Resistor Control Register CSN, SCLK, MOSI, TXD, TRSTN, TCK, TMS, and WDT_DIS each contain a configurable internal pull-down resistor that is active by default. The pull-down resistors are present to prevent a floating input pin if the bonding wire is broken and to enable the system to detect such a broken wire or broken connections with the external microcontroller. Example: If the bonding wire at TXD is broken, the pull-down resistor would drive TXD low continuously and the LIN TXD timeout detector will trigger and inform the external microcontroller that an error is present. Directly behind the input pins is a secondary protection stage because VDDP is disabled in some power-down states. The ZSSC1750/51’s three SPI inputs, CSN, SCLK, and MOSI, as well as the TXD input, are only enabled in FP State. The WDT_DIS input is enabled as long as MCU_RSTN is high (in the FP or LP State) while the ZSSC1750/51’s three test inputs, TRSTN, TCK, and TMS, are only enabled when TEST is high. Note: Because the TEST input pin also contains a pull-down resistor, disabling the pull-down resistors for the three test input pins is safe as long as TEST is low. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 106 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Table 3.68 Register pullResEna Name Address Bits Default Access pullResEnaCsn [0] 1BIN RW pullResEnaSpiClk [1] 1BIN RW pullResEnaMosi [2] 1BIN RW pullResEnaTxd [3] 1BIN RW [4] 1BIN RW pullResEnaTck [5] 1BIN RW pullResEnaTms [6] 1BIN RW pullResEnaWdtDis [7] 1BIN RW pullResEnaTrstn B8HEX Description When set to 1, the pull-down resistor behind the CSN pin is connected to the pin. When set to 1, the pull-down resistor behind the SCLK pin is connected to the pin. When set to 1, the pull-down resistor behind the MOSI pin is connected to the pin. When set to 1, the pull-down resistor behind the TXD pin is connected to the pin. When set to 1, the pull-down resistor behind the TRSTN pin is connected to the pin. When set to 1, the pull-down resistor behind the TCK pin is connected to the pin. When set to 1, the pull-down resistor behind the TMS pin is connected to the pin. When set to 1, the pull-down resistor behind the WDT_DIS pin is connected to the pin 3.11.1.2 Register “versionCode” – Version Code of SBC The version code of the SBC is 200HEX. Table 3.69 Register versionCode Name versionCode[7:0] versionCode[11:8] Unused Data Sheet July 10, 2014 Address Bits BAHEX [7:0] [3:0] [7:4] BBHEX Default 00HEX 0010BIN 0000BIN Access RO RO RO Description Version code of the SBC. Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 107 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.11.1.3 Register “pwrTrim” – Trim Register for the Voltage Regulators and Bandgap Table 3.70 Register pwrTrim Name Address vddcTrim vddpTrim Bits Default [0] 0BIN [1] 0BIN Access RW Trim register for VDDC regulator: RW 0 VDDC is trimmed to 1.2V 1 VDDC is trimmed to 1.8V Note: This register is set by the OTP download procedure when the OTP content is valid. Trim register for the VDDP regulator: C0HEX vbghTrim Description 0 1 [7:2] 011111BIN RW VDDP is trimmed to 2.5V VDDP is trimmed to 3.3V Note: This register is set by the OTP download procedure when the OTP content is valid. Trim register for the high-precision bandgap. Note: This register is set by the OTP download procedure when OTP content is valid. Important Warning: Changing the settings of bits vddcTrim and vddpTrim could cause damage to the connected external microcontroller or cause it to malfunction! 3.11.1.4 Register “ibiasLinTrim” – Trim Register for the Bias Current of the LIN Block Table 3.71 Register ibiasLinTrim Name Address ibiasLinTrim Bits Default Access [4:0] 10000BIN RW Data Sheet July 10, 2014 Trim register for the bias current of the LIN block: 0 1 C3HEX Unused Description [7:5] 000BIN RO Smallest value Largest value Note: This register is set by the OTP download procedure when OTP contents are valid. Unused; always write as 0. © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 108 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.12 Voltage Regulators In addition to the battery voltage (VBAT), four additional voltage domains are implemented in the ZSSC1750/51 as described in the following sections. The VDDA supply voltage for the analog sections is generated in the VDDA_REG block and available on the VDDA pin. The VDDL voltage for the digital sections during the ZSSC1750/51’s LP State is generated in the LP_REG block and output on the VDDL pin, and it can be used as an optional low-power supply for the external microcontroller. The VDDP supply voltage for the SBC’s I/O circuits is generated in the VDDP_REG block and output on the VDDP pin as an optional supply for the external microcontroller. The VDDC supply voltage, an optional supply for the external microcontroller, is generated in the VDDC_REG block and output on the VDDC pin. The regulators are low-dropout regulators (LDOs). The VDDL regulator, which is active in the low-power states, has very low power consumption. 3.12.1 VDDE The following blocks are connected directly to VDDE: Low-power bandgap High-precision bandgap High-precision oscillator POR Regulator for VDDA Regulator for VDDL Regulator for VDDC Regulator for VDDP 3.12.2 VBAT VBAT is the input for the battery voltage measurement using the voltage ADC. It is connected to a resistive divider, dividing VBAT to a usable single-ended voltage for the voltage ADC (maximum 1.2V). 3.12.3 VDDA The analog regulator provides a 2.5V output and can drive up to 10mA of load current. The output voltage is continuously regulated with respect to the bandgap voltage (vbgh). A resistor chain generates the appropriate voltage for the feedback comparison with the bandgap voltage so that the correct voltage is generated. This internal regulated voltage serves as a supply voltage for the analog blocks. The analog regulator can be switched off (e.g., in Sleep Mode). The following blocks are connected directly to VDDA: Level-Shifter PGA Divider Temperature Measurement SD-ADC Channel 1 (current) SD-ADC Channel 2 (voltage and temperature) All blocks necessary for data acquisition (current, voltage, and temperature measurements) Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 109 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 3.12.4 VDDL The VDDL regulator provides the supply voltage for the ZSSC1750/51’s digital domain. This regulator remains active in ULP and OFF States. The following blocks are connected directly to VDDL: LIN PHY control (ZSSC1750 only) Power Management Unit All ZSSC1750/51 registers Watchdog timer 3.12.5 VDDP The peripheral regulator provides 3.3V. The VDDP regulator can drive up to 40mA of load current and can be switched off (e.g., in Sleep Mode). This voltage is recommended for the supply of the external microcontroller to ensure matching I/O voltage levels as the I/O blocks of the ZSSC1750/51 are also connected directly to VDDP. VDDP can be trimmed to the lower range given in specification 1.3.9 using the vddpTrim bit field in Table 3.70. Important Warning: An improper vddpTrim setting could cause damage to the connected external microcontroller or cause it to malfunction! See section 3.3.4 regarding VDDP trimming and the reset function. 3.12.6 VDDC The core regulator provides 1.8V. This regulator can drive up to 40mA of load current and can be switched off (e.g., in Sleep Mode).This voltage can be used for powering the core of an external microcontroller that requires a lower core voltage than VDDP. VDDC can be trimmed to the lower range given in specification 1.3.8 using the vddcTrim bit field in Table 3.70. Important Warning: An improper vddcTrim setting could cause damage to the connected external microcontroller or cause it to malfunction! Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 110 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 4 ESD / EMC The ZSSC175x is designed to maximize EM immunity and minimize emissions. (References to LIN communication are only applicable to the ZSSC1750.) Functional status A: According to specifications; no LIN communication errors; memory content must not be lost; no wake-up from Sleep Mode; no reset. Functional status B: According to specifications; offset error extended to < 100mA; no LIN communication errors; memory content must not be lost; no wake-up from Sleep Mode; no reset. Functional status C: Measurement tolerance beyond specifications; LIN communication errors allowed; memory content must not be lost; reset allowed. During EM exposure, all functions perform as designed; after exposure, all functions return automatically to within normal limits; memory functions always remain in functional status A. 4.1 Electrostatic Discharge Table 4.1 No. ESD Protection According to AEC-Q100 Rev. G Parameter 4.1.1. ESD, LIN on system level Condition 1) 2) Min Max Unit IEC 61000-4-2 ±6 kV IEC 61000-4-2 ±6 kV 4.1.2. ESD, BAT+ on system level 4.1.3. ESD, HBM, all other pins AEC Q 100-002 ±2 kV 4.1.4. ESD, CDM, corner pins AEC Q 100-011 ±750 V 4.1.5. ESD, CDM, all other pins AEC Q 100-011 ±500 V 1) 2) 4.2 For higher ESD levels additional diode is required (see Figure 4 1). With external protection diode GSOT36 (see Figure 4.1). Power System Ripple Factor Component functionality meets these specifications. UN = 13.5V Voltage variation: sine wave Amplitude V = ±2V Frequency range: 50Hz ≤ f ≤ 25kHz (linear sweep width for 10 minutes) Ri of output stage ≤ 100m Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 111 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 4.3 Application Circuit Examples for EMC Conformance The final application might require adaption of the external circuit for EMC compliance in the target system as shown in Figure 4.1 and Figure 4.2. Figure 4.1 Optional External Components for ZSSC1750 BAS21 2.2Ω VDDL ZSSC1750 INN Cinn 10nF WDT_DIS wdt_dis MCU_CLK mcu_clk VSSA Rntc 10kΩ sto VDDA TCK tck NTH TMS tms NTL Cntc 470pF RXD rxd txd mcu_rstn irqn TRSTN MISO Rref 75kΩ STO MOSI Cdda 470nF n.c . SCLK Rinn n.c. TESTL INP Cin 100nF BAT220Ω TESTH VSSA CSN 220Ω Rshunt 100µΩ Cinp 10nF LIN VSSLIN VSSE MCU_RSTN Rinp 100nF TXD Chassis GND 10µF TEST VDDE SLEEPN VDDP VBAT 1 Rdde Cdde1 Cdde2 LIN Clin 220pF Dlin GSOT36 IRQN Ddde Cddp 2.2µF VDDC Dbat GSOT36 VPP 100Ω Cddl 10nF VSSR Cbat 100nF sleepn Cddc 2.2µF Rbat BAT+ Ferrite Llin BLM21AG221SN1D or Resistor Rlin - 20Ω csn sclk mosi miso trstn VSSN Figure 4.2 Optional External Components for ZSSC1751 Rinn Cdda 470nF open VSSR n.c. TESTL n.c . Cinn 10nF Rref 75kΩ Rntc 10kΩ ZSSC1751 INN BAT220Ω TESTH INP Cin 100nF WDT_DIS wdt_dis MCU_CLK mcu_clk VSSA STO sto VDDA TCK tck TMS tms NTH NTL Cntc 470pF VSS VSSA NC NC MISO 220Ω NC VSSE MOSI Rshunt 100µΩ Cinp 10nF SCLK Rinp 100nF CSN Chassis GND 10µF IRQN BAS21 2.2Ω Cddl 10nF VDDL VBAT VDDE TEST 1 VDDC Rdde Cdde1 Cdde2 MCU_RSTN Ddde VDDP Dbat GSOT36 VPP 100Ω Cddp 2.2µF SLEEPN Cbat 100nF sleepn Cddc 2.2µF Rbat BAT+ csn sclk mosi miso TRSTN trstn VSSN VDDP open mcu_rstn irqn Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 112 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 5 Pin Configuration and Package Figure 5.1 ZSSC1750/51 PQFN36 6x6mm Package Pin-out (Top View) ZSSC1750 SLEEPN VDDL VSSR LIN VBAT VPP VDDP VDDC 32 31 30 29 28 36 35 34 33 VDDE 1 27 VSSLIN VDDE 1 VSSE 2 26 TESTH VSSE VSSA 3 25 TESTL VSSA INP 4 24 WDT_DIS INP 4 23 MCU_CLK EXPOSED PAD (pin 37) NC (1) TEST 33 VSSR VDDC 34 VDDL VDDP 35 TEST VPP 36 SLEEPN VBAT ZSSC1751 32 31 30 29 28 27 VSS 2 26 TESTH 3 25 TESTL 24 WDT_DIS 23 MCU_CLK EXPOSED PAD (pin 37) 9 19 NTL 9 19 TRSTN 10 11 12 13 14 15 16 17 18 TRSTN 10 11 12 13 14 15 16 17 18 VSSN 20 TMS NTL MISO 8 MOSI NTH CSN 20 TMS SCLK 8 IRQN NTH NC (1) 21 TCK MCU_RSTN 7 NC (1) VDDA VSSN STO TCK MISO 22 21 MOSI 6 7 SCLK VSSA VDDA CSN STO IRQN 22 MCU_RSTN 5 6 TXD INN VSSA RXD INN 5 (1): See Table 5.1 for proper pin termination for no-connection (NC) pins. Table 5.1 ZSSC1750/51 Pins Description Note: See important notes at the end of the table. Pin Pin Name Type Mode 1 VDDE Supply Input Power supply 2 VSSE Supply Input Power ground 3 VSSA Supply Input Analog voltage ground 4 INP Analog Input Positive input for current channel 5 INN Analog Input Negative input for current channel 6 VSSA Supply Input Analog voltage ground 7 VDDA Analog Output Analog voltage supply 8 NTH Analog Input Positive input for the temperature channel 9 NTL Analog Input Negative input for the temperature channel RXD Digital Output NC N/A N/A Not used in ZSSC1751 – keep open Digital Input LIN transmitter input for ZSSC1750 only 10 11 Data Sheet July 10, 2014 TXD 1) Description LIN receiver output for ZSSC1750 only © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 113 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Pin Pin Name Type Mode NC N/A N/A 12 MCU_RSTN Digital Output Reset for external microcontroller 13 IRQN Digital Output Interrupt for external microcontroller 14 CSN 15 16 1) Description Not used in ZSSC1751 – connect to VDDP Digital Input SPI chip select SCLK 1) Digital Input SPI clock MOSI 1) Digital Input SPI Master output, Slave input SPI master input, slave output 17 MISO Digital Output 18 VSSN Supply Input Digital voltage ground 19 TRSTN 1), 2) Digital Input Test interface TMS 1), 2) Digital Input Test interface TCK 1), 2) Digital Input Test interface Digital Output Test interface Digital Output Clock signal to external microcontroller (20MHz) Digital Input Watchdog timer disable pin Analog In/Out Test interface Analog In/Out Test interface VSSLIN Supply Input LIN ground for ZSSC1750 VSS Supply Input Power ground for ZSSC1751 LIN Analog In/Out LIN bus for ZSSC1750 NC N/A N/A Not used in ZSSC1751 – keep open. 29 VSSR Supply Input Power ground 30 VDDL Analog Output SBC digital core supply 31 SLEEPN Digital Output SBC power state indicator pin 32 TEST Digital Input 33 VDDC Analog Output External microcontroller supply voltage (core) 34 VDDP Analog Output External microcontroller supply voltage (periphery) 35 VPP Analog Input OTP programming voltage 36 VBAT Analog Input Input for battery voltage monitor 37 EXPOSED PAD Supply Input Connect to VSSE in application 20 21 22 STO 23 MCU_CLK 24 WDT_DIS 25 2) TESTL 26 TESTH 1) 2) 27 28 Test interface enable; connect to ground in application 1) Digital input with internal pull-down resistor. See parameter RPULL_DOWN in Table 1.3. 2) Connect to ground in application. Data Sheet July 10, 2014 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 114 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Figure 5.2 Package Drawing of the ZSSC1750/51 Dimensions Min (mm) (mm) A 0.8 0.9 A1 0 0.05 b 0.2 0.3 E Data Sheet July 10, 2014 0.5 nom HD 5.9 6.1 HE 5.9 6.1 L 0.45 0.65 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 115 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) 6 Ordering Information Product Sales Code Description Package ZSSC1750EA1B ZSSC1750 Battery Sensing SBC—Temperature Range: -40°C to 125°C Tested die on unsawn wafer ZSSC1750EA3R ZSSC1750 Battery Sensing SBC—Temperature Range: -40°C to 125°C PQFN36 6x6 mm, reel ZSSC1751EA3R ZSSC1751 Battery Sensing SBC—Temperature Range: -40°C to 125°C PQFN36 6x6 mm, reel ZSSC1750KIT V1.1 ZSSC1750/51 Evaluation Kit: modular evaluation and development board for ZSSC1750/51, 3 IC samples, and USB cable, (software and documentation can be downloaded from the product page at www.zmdi.com/zssc175x) 7 Related Documents Note: Rev_X_xy.pdf designates the current revision number of the document. Document File Name ZSSC1750/51 Feature Sheet ZSSC1750/51_SBC_Feature_Sheet_Rev_X_xy.pdf Application Notes See product web page. Technical Note – Die Pad Dimensions and Coordinates Available upon request. Visit the ZSSC175x product page www.zmdi.com/zssc175x on ZMDI’s website www.zmdi.com or contact your nearest sales office for the latest version of these documents. 8 Glossary Term Description ADC Analog-to-Digital Converter BIST Built-In Self-Test DAP Debug Access Port ECC Error Correction Code FP Full Power State FSR Full Scale Range IFC Current Interface IFT Temperature Interface ITS Internal Temperature Sensor LIN Local Interconnect Network LP Low Power state LSB Least Significant Bit or Byte Depending on Context Data Sheet © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. July 10, 2014 116 of 117 ZSSC1750/51 Data Acquisition System Basis Chip (SBC) Term Description MCU Micro Controller Unit (external microcontroller) MPX Multiplexer MRCS Multiple Results per Conversion Sequence MSB Most Significant Bit NMI Non-maskable Interrupt NTC Negative Temperature Coefficient OTP One-Time Programmable Memory PA-C Preamplifier for Current PA-T Preamplifier for Temperature PGA Programmable Gain Amplifier POR Power-On-Reset PPB Private Peripheral Bus PTAT Proportional to Absolute Temperature SBC System Basis Chip SDM Sigma Delta Modulator SPI System Packet Interface SRCS Single Result per Conversion Sequence ULP Ultra Low Power State 9 Document Revision History Revision Date Description 1.00 July 10, 2014 First release. Sales and Further Information www.zmdi.com [email protected] Zentrum Mikroelektronik Dresden AG Global Headquarters Grenzstrasse 28 01109 Dresden, Germany ZMD America, Inc. 1525 McCarthy Blvd., #212 Milpitas, CA 95035-7453 USA Central Office: Phone +49.351.8822.306 Fax +49.351.8822.337 USA Phone: 1.855.275.9634 Phone +1.408.883.6310 Fax +1.408.883.6358 European Technical Support Phone +49.351.8822.7.772 Fax +49.351.8822.87.772 DISCLAIMER: This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Zentrum Mikroelektronik Dresden AG (ZMD AG) assumes no obligation regarding future manufacture unless otherwise agreed to in writing. The information furnished hereby is believed to be true and accurate. However, under no circumstances shall ZMD AG be liable to any customer, licensee, or any other third party for any special, indirect, incidental, or consequential damages of any kind or nature whatsoever arising out of or in any way related to the furnishing, performance, or use of this technical data. ZMD AG hereby expressly disclaims any liability of ZMD AG to any customer, licensee or any other third party, and any such customer, licensee and any other third party hereby waives any liability of ZMD AG for any damages in connection with or arising out of the furnishing, performance or use of this technical data, whether based on contract, warranty, tort (including negligence), strict liability, or otherwise. European Sales (Stuttgart) Phone +49.711.674517.55 Fax +49.711.674517.87955 Data Sheet July 10, 2014 Zentrum Mikroelektronik Dresden AG, Japan Office 2nd Floor, Shinbashi Tokyu Bldg. 4-21-3, Shinbashi, Minato-ku Tokyo, 105-0004 Japan ZMD FAR EAST, Ltd. 3F, No. 51, Sec. 2, Keelung Road 11052 Taipei Taiwan Phone +81.3.6895.7410 Fax +81.3.6895.7301 Phone +886.2.2377.8189 Fax +886.2.2377.8199 Zentrum Mikroelektronik Dresden AG, Korea Office U-space 1 Building 11th Floor, Unit JA-1102 670 Sampyeong-dong Bundang-gu, Seongnam-si Gyeonggi-do, 463-400 Korea Phone +82.31.950.7679 Fax +82.504.841.3026 © 2014 Zentrum Mikroelektronik Dresden AG — Rev.1.00 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 117 of 117