TAI-SAW TECHNOLOGY CO., LTD. No. 3, Industrial 2nd Rd., Ping-Chen Industrial District, Taoyuan, 324, Taiwan, R.O.C. TEL: 886-3-4690038 FAX: 886-3-4697532 Web: www.taisaw.com E-mail: [email protected] SAW Filter 119.64MHz MODEL NO.: TB0196A REV. NO.:2 A. MAXIMUM RATING: 1. Input Power Level: 10 dBm 2. DC voltage : 13 V RoHS Compliant Lead free Lead-free soldering 3. Operating Temperature: -20°C to +75°C 4. Storage Temperature: -40°C to +85°C Electrostatic Sensitive Device (ESD) B. ELECTRICAL CHARACTERISTICS: Item Unit Center frequency, Fc Minimum Insertion Loss, IL 3 dB bandwidth (from Fc) Group delay ripple in Fc±15KHz, GD MHz Min. - Typ. 119.64 Max. - Note - dB - 4 5.5 - KHz ±15 - - - μs - 5 10 - dB - 1.2 3.0 - dB 13 23 - - Attenuation:(Reference level from min IL) Fc - 2.5 to Fc ± 80 to Fc + 2.5 KHz Fc ± 120 KHz Fc ± 120 to Fc ± 240 KHz dB 43 50 - - Fc ± 240 to Fc ± 330 KHz dB 45 55 - - Fc ± 330 to Fc ± 480 KHz dB 45 55 - - Fc ± 480 to Fc ± 660 KHz dB 45 55 - - Temperature coefficient of frequency S o u rc e im p e d a n c e TCf -0.033 ppm/C^2 L o a d im p e d a n c e 50Ω 50Ω Z IN = 4 1 6 .2 Ω // -4 .6 5 p F Z O U T = 4 1 6 .2 Ω // -4 .6 5 p F TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 2 C. OUTLINE DRAWING: 196 T B□ Pin configuration #9 Input #4 Output #10 Balance input or input ground #5 Balance output or output ground #1,2,3,6,7,8 To be grounded □ Date code Unit mm D. MEASUREMENT CIRCUIT: 50 Ohm Test circuit 1 ( single-ended / single-ended ) HP Network analyzer IN 180nH 180nH 9 OUT 4 SAW Filter 50Ω 10 50Ω 5 4pF 4pF 1,2,3,6,7,8 50 Ohm Test circuit 2 ( balance / balance ) HP Network analyzer IN 18pF 150nH 150nH 9 50Ω SAW Filter 50Ω 5 10 1:1 OUT 18pF 4 18pF 18pF 1:1 1,2,3,6,7,8 TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 3 E. PCB Footprint: TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 4 F. Frequency Characteristics : TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 5 G. PACKING: 1. REEL DIMENSION (Reel Count : 7”=1000 or per the request of customer order ) 2.TAPE DIMENSION 1208 96 TB TB Direction of Feed TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 6 H. RECOMMENDED REFLOW PROFILE : 1. 2. 3. 4. Preheating shall be fixed at 150~180℃ for 60~90 seconds. Ascending time to preheating temperature 150℃ shall be 30 seconds min. Heating shall be fixed at 220℃ for 50~80 seconds and at 245~260℃ peak (min. 10sec). Time : 2 times. TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 7