CONVENTIONAL LED LAMPS Standard Type Square Type LED Lamps SLB-25 Series Yellow Green Emitting Surface Dimension (mm) Shape GaP Red GaAsP on GaP 563nm 585nm 610nm 650nm SLB-25MG SLB-25YY SLB-25DU SLB-25VR 2×5 ■ Absolute Maximum Ratings（Ta=25℃） ■ External Dimensions（Unit：mm） 5.0 Yellow SLB-25DU Orange SLB-25VR Red 75 25 60 20 60 3 -25 to +85 -30 to +100 1.25 Green SLB-25YY 5.1±0.3 1.0Max. SLB-25MG 2.0 2.1 2.8±0.3 Peak Reverse Operating Stotage Power Forward forward Emitting dissipation current voltage temperature temperature current color PD IF VR Topr Tstg IFP （mW） （mA） （V） （°C） （°C） （mA） (6.25) 7.5±0.3 Square Type 4−0.6 ＊IFP measured under duty ≦1/ 5,pulse width ≦1ms. Part No. Resin Color Forward voltage VF Typ. (V) SLB-25MG SLB-25YY SLB-25DU SLB-25VR IF (mA) Reverse current IR Max. (µA) VR (V) Typ. (nm) Brightness IV （2.5） Typ. (nm) IF (mA) 40 10 Min. Typ. IF ( mcd) (mcd) (mA) 563 2.1 Colored Diffused Light wavelength Peak Half-wave ∆λ λp 10 10 3 585 CATHODE Tolerance:±0.2 ■ Directivity 610 2.0 2.5±1.0 □0.5 ■ Electrical Optical Characteristics（Ta=25℃） 24.0Min. Part No. Orange 0.36 1.0 10 X 0° 650 30° 30° − − −Y − X' Y' X Y X' Y' 60° 60° 90° 100 50 0 50 Relative Luminous Intensity (%) ■ Recommemded Pad Layout ■ Packaging Spacifications（Unit：mm） Packaging Bulk（3F）：1000pcs/Box 1.0 ±0.1 2.0 2.5 70 170 100 （Unit：mm） 90° 100 (TYP.) CONVENTIONAL LED LAMPS ■ Electrical Characteristic Curves Relative Luminous Intensity - Case Temperature Forward Current - Forward Voltage SLB-25MG 20 SLB-25DU 10 SLB-25VR 5.0 2.0 1.0 0.5 0.2 0.1 1.0 SLB-25MG 1.4 SLB-25YY Ta=25℃ 1.5 2.0 2.5 RELATIVE LUMINOUS INTENSITY FORWARD CURRENT : IF (mA) 50 SLB-25DU 1.2 SLB-25VR 1.0 0.8 0.6 0.4 −20 3.0 SLB-25YY FORWARD VOLTAGE : VF (V) 0 20 40 60 80 CASE TEMPERATURE(℃) Ratio of Maximum Tolerable Peak Current - Pulse Duration Relative Luminous Intensity - Forward Current SLB-25MG 0.1 0.1 1 10 1 MAXIMUM FORWARD CURRENT : IF Max. (mA) SLB-25MG SLB-25YY SLB-25DU SLB-25VR 40 50 60 70 80 90 30 AMBIENT TEMPERATURE : Ta (℃) 10 100 100Hz 200Hz 1kHz 2kHz 500Hz 1000 PULSE DURATION : Tw (usec) Derating 10 2.4 1 FORWARD CURRENT : IF (mA) 20 3 10kHz 5kHz SLB-25VR 20kHz SLB-25DU SLB-25VR 100 30 SLB-25YY SLB-25DU 1 0 20 SLB-25MG 10 SLB-25YY 50kHz Ta＝25℃ IFP Max／IF Max RELATIVE LUMINOUS INTENSITY 10 10000 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1