VER : A_4 update : 2013.12.05 AC-DC Switching Power Supply AQF600 SERIES 600 Watts KEY FEATURES Universal Input: 90-264 VAC With P.F.C. Function, PF>0.95 Remote ON/OFF Function Current Share Function Power Good Function High Efficiency up to 90~93% Protections: Over Load / Over Voltage / .Over Temperature / Short Circuit High Power Density RoHS Compliant Design 3-Years Product Warranty ELECTRICAL SPECIFICATIONS Model No. Max Output Wattage (Convection) Voltage (W) Output Protection Isolation Function Environment AQF600-24S AQF600-48S AQF600-54S 540W 600W 600W 600W 90-264 VAC or 120-370 VDC Frequency (Hz) Input AQF600-12S 47-63 Hz Current (Full load) < 8.0 A max. (115 VAC) / < 3.5 A max. (230 VAC) Inrush Current (<2ms) < 15 A max. (115 VAC) / < 30 A max. (230 VAC) Leakage Current < 3.5 mA max.(240VAC 63Hz) Power Factor PF>0.99 (115 VAC) / PF>0.95 (230 VAC) at Full Load Voltage (V.DC.) 12V Trim ±5% Voltage Accuracy ±2% Current (Convection) (A) max 45 Line Regulation (LL-HL) (typ.) ±1% Load Regulation (5-100%) (typ.) ±1% Minimum Load 1% Maximum Capacitive Load 60,000 uF Ripple & Noise (max.) < 1% Vout Efficiency (typ.) 90% Hold-up Time 12 ms min. Switching Frequency 110±10 KHz Over Power Protection Auto recovery Over Voltage Protection Auto recovery Over Temperature Auto recovery Short Circuit Protection Latch off Input-Output (V.AC) 3000V Input-FG (V.AC) 1500V Output-FG .(V.AC) 24V 48V 54V 25 12.5 11.1 50,000 uF 20,000 uF 10,000 uF 92% 92% 93% 500V 5V Stand by (18CFM FAN) 5VSB: [email protected] ; Tolerance 10% , Ripple & Noise: 100m Vp-p (max.) DC OK Signal (Power Good) Turn ON: 3.7~5.7V ; Turn OFF: 0~1V Remote Control +RC / -RC: Power ON=open ; Power OFF=short Current Share CN4:CS, +V, -V are connected mutually in parallel. Operating Temperature -25°C…+65°C (with derating) Storage Temperature -25°C…+85°C Temperature Coefficient ±0.03%/°C ( 0~50°C ) Humidity 95% RH MTBF >100,000 h @ 25°C (MIL-HDBK-217F) Vibration 10~500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes. 1. All specifications valid at normal input voltage, full load and +25°C after warm-up time unless otherwise stated. 2. Ripple & Noise are measured at 20MHz of bandwidth with 0.1uF & 47uF parallel capacitor. http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 -1- VER : A_4 update : 2013.12.05 AC-DC Switching Power Supply AQF600 SERIES 600 Watts ELECTRICAL SPECIFICATIONS Model No. AQF600-12S Dimension (L x W x H) Physical Safety EMC AQF600-24S 9.0 x 4.13 x 1.72 Inches Weight 1024±50 g Cooling Integral fan Agency Approvals CE, UL60950-1 AQF600-48S AQF600-54S (228.5 x 105.0 x 44.0 mm ) Tolerance 0.5 mm EMI (Conducted & Radiated Emission) EN 55022 class B, Radiated Class A EMS (Noise Immunity) EN 55024 Surge 1KV L-N, 2KV L N-FG 1. All specifications valid at normal input voltage, full load and +25°C after warm-up time unless otherwise stated. 2. Ripple & Noise are measured at 20MHz of bandwidth with 0.1uF & 47uF parallel capacitor. BLOCK DIAGRAM DERATING http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 -2- VER : A_4 update : 2013.12.05 AC-DC Switching Power Supply AQF600 SERIES 600 Watts MECHANICAL DIMENSION AC Input Terminal Pin PIN# SINGLE 1 AC IN DC Output Terminal Pin PIN# SINGLE 2~4 +DC OUT 5~7 -DC OUT Connector Pin (CN4) PIN# SINGLE C1 +S C2 -S C3 CS C4 GND C5 GND C6 +RC C7 +PG C8 +5V-AUX ASSEMBLY INSTRUCTIONS *U Case T=2.0mm Customer screws into the length of the case no higher than 0.5mm (Namely screw length for load plate thickness plus 2.5mm http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 -3- VER : A_4 update : 2013.12.05 AC-DC Switching Power Supply AQF600 SERIES 600 Watts FUNCTION DESCRIPITON of CN4 Pin No. Function C1 +S Description Current Share Function Pin C2 -S C3 CS C4 GND C5 GND This pin connects to the negative terminal(-V). Return for DC-OK signal output. C6 +RC Turns the output on and off by electrical or dry contact between pin C4 (-RC), Short: Power OFF, Open: Power ON. C7 +PG C8 +5V-AUX This pin connects to the negative terminal(-V). Return for DC-OK signal output. DC-OK Signal is a DC output, referenced to pinC6(DC-OK GND). Stand by voltage output ground 4.5~5.5V, referenced to pin C4 or C5(GND). The maximum load current is 0.6A. FUNCTION MANUAL & APPLICATION NOTE 1. DC-OK Signal Between DC-OK(pinC5) and GND(pinC6) Output Status 3.7~5.7V 0~1V ON OFF 2. Remote Control It can be turned ON/OFF by using the "Remote Control" function. Between RC+(pinC3) and RC-(pinC4) Output Status SW ON (Short) SW OFF (Open) OFF ON 3. Current Share 1. Difference in Vout among parallelled units should be less than +/-1% 2. Output Power at Parallel Operation = Rated Power per Unit x Number of Unit x 80% 3. Connect in parallel no more than 2 units. Please contact Arch for advice if more than 2 is needed. 4. Shorter wiring to each unit is recommended, as well as twisting +S and -S in pairs, as shown below 5. The remote sensing compensates voltage drop on the load wiring up to 5V http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 -4- VER : A_4 update : 2013.12.05 AC-DC Switching Power Supply AQF600 SERIES 600 Watts 4. 1+1 Redundancy：sing 1 more AQF600 as the redundant unit 5. 1+N Redundancy: Using more AQF600 as the redundant units to increase the reliability http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 -5-