nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 NF1010E (Built-in I2C EEPROM) nFore Bluetooth v4.0 Module Hardware Specification Data Sheet Copyright 2006 by nFore Technology Co., Ltd. All Rights Reserved. Reproduction of this document, in part of in whole, by any means is prohibited without written permission from nFore Co., Ltd. The information contained herein is believed to be accurate as of the date of publication. However, nFore is not liable for any damages, including indirect or consequential from the use of software this document represents, or any reliance of the accuracy of this document. nFore reserves the right to change the contents of this document at any time without notice. This document contains proprietary confidential trade secrets and may be subject to additional restrictions contained in the licensing agreement under which this document was obtained. 1 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 Revision History Revision Revised date 0.1 2014.10.30 0.2 2014.11.06 Description Revised by Preliminary release Update Module Picture(P.1) Update Block Diagram(P.7) Jordan Jordan 2 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 1 OVERVIEW............................................................................................................................................................................. 4 2 PACKAGE INFORMATION ................................................................................................................................................. 5 2.1 2.2 2 SIGNAL LAYOUT (TOP VIEW) ............................................................................................................................................ 5 PIN DESCRIPTION .............................................................................................................................................................. 6 FUNCTIONAL FEATURES................................................................................................................................................... 7 2.3 MODULE BLOCK DIAGRAM ............................................................................................................................................... 7 2.4 HARDWARE INTERFACE ..................................................................................................................................................... 8 2.4.1 Reset Interface............................................................................................................................................................. 8 2.4.2 UART Interface............................................................................................................................................................ 9 3 MODULE SPECIFICATION ............................................................................................................................................... 10 3.1 3.2 ELECTRICAL CHARACTERISTICS...................................................................................................................................... 10 RF CHARACTERISTIC ...................................................................................................................................................... 11 4 MECHANICAL CHARACTERISTICS.............................................................................................................................. 12 5 SMT AND BAKING RECOMMENDATION ..................................................................................................................... 14 5.1 5.2 5.3 BAKING RECOMMENDATION ........................................................................................................................................... 14 SMT RECOMMENDATION ................................................................................................................................................ 14 ORDERING INFORMATION ................................................................................................................................................ 15 3 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 1 OVERVIEW NF1010 is a highly integrated Bluetooth module. NF1010 is the most demanded design for Healthcare, Sports and fitness, Home entertainment. NF1010 design with CSR1010 BT v4.0 /BLE solutions to provide Dual mode for Bluetooth. NF1010 module is a product from the CSR uEnergy platform. CSR uEnergy enables ultra low-power connectivity and basic data transfer for applications previously limited by power consumption, size constraints and complexity of the other wireless standards. nFore is the industry leader for Bluetooth low energy Module. Bluetooth low energy enables the transfer of simple data sets between compact devices opening up a completely new class of Bluetooth application such as watched, TV remote controls, medical sensors and fitness trainers General Features ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Bluetooth v4.0 specification Bluetooth low energy High TX output power without an external PA Bluetooth low energy RX High sensitivity Support for Bluetooth v4.0 Specification host stack including ATT, GATT, SMP, L2CAP, GAP RSSI monitoring for proximity applications <600nA current consumption in dormant mode 32kHz and 16MHz crystal Switch-mode power supply Programmable general purpose PIO controller 3 AIOs(10-bit ADC) 7 digital PIOs 3 analogue AIOs UART Built-in I2C EEPROM:512k-bit(OTA) 3 PWM modules Wake-up interrupt 64KB RAM and 64KB ROM Built in Serial SPI Flash ROM(512kb) Watchdog timer No external clock source needed Applications for Healthcare, Sports and fitness, Automotive and Human interface devices. Dimension 11.5mm(L) x 11.5mm(W) x 1.8mm(H) Operating Voltage : VDD_BT_3V3: 3.3V±10% ; VDD_PADS: 1.8V ~ 3.3V Stamp package module suitable for Surface Mounted Technology (SMT) Stamp package Size: 11.5(L)X11.5(W)X1.8(H)mm RoHS / REACH Compliant Near to Industrial Level(-30℃ to +85℃) 4 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 2 Package Information AIO2 AIO1 AIO0 GND UART_TX UART_RX GND VDD_BT_3V3 VDD_BT_3V3 VDD_PADS VDD_PADS GND SPI_PIO_SEL 20 19 18 17 16 15 14 7 8 9 10 11 12 13 PIO5 PIO6 PIO7 PIO8 PIO9 PIO10 PIO11 1 2 3 4 5 6 RF_IN/OUT GND WAKE SF_DIN SF_CS SF_DOUT SF_CLK 27 26 25 24 23 22 21 2.1 Signal Layout (Top View) 5 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 2.2 Pin Description No. Name 1 2 3 4 5 6 7 Type Description B B B GND O I B 11 AIO2 AIO1 AIO0 GND UART_TX UART_RX PIO5 DEGUG_CLK PIO6 DEGUG_CS# PIO7 DEGUG_MOSI PIO8 DEGUG_MISO PIO9 12 13 14 15 16 17 18 19 20 21 22 23 24 25 25 27 PIO10 PIO11 SPI_PIO_SEL GND VDD_PADS VDD_PADS VDD_BT_3V3 VDD_BT_3V3 GND SF_CLK/I2C_SCL SF_OUT/I2C_SDA SF_CS/PIO4 SF_DIN/PIO3 WAKE GND RF IN/OUT B B I GND P P P P GND I B B B I GND RF 8 9 10 B B I B O B Analogue programmable I/O line Analogue programmable I/O line Analogue programmable I/O line GROUND UART data output, active high UART data input, active high Programmable I/O line SPI clock Programmable I/O line SPI clock Programmable I/O line SPI data input Programmable I/O line SPI data output Programmable I/O line Programmable I/O line Programmable I/O line Selects SPI debug on PIO[8:5] GROUND Positive supply for PIO,UART Positive supply for PIO,UART Positive supply for Module internal LDO regulator Positive supply for Module internal LDO regulator GROUND SPI serial flash clock output/I2C clock SPI serial flash data output/I2C data input/output SPI serial flash chip select/Programmable I/O line SPI serial flash data input/Programmable I/O line Input to WAKE NF1010S from Host side GROUND RF IN/OUT 6 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 2 FUNCTIONAL FEATURES 2.3 Module Block Diagram 7 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 2.4 Hardware interface 2.4.1 Reset Interface Reset Interface NF1010 the reset function is internally tied to the RESETB pin. NF1010 may be reset from several sources: ■ Power-on reset ■ Via a software-configured watchdog timer . 8 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 2.4.2 UART Interface This is a standard UART interface for communicating with other serial devices. NF1010 UART interface provides a simple mechanism for communicating with other serial devices using the RS-232 protocol. 2 signals implement the UART function, UART_TX and UART_RX. When NF1010 is connected to another digital device, UART_RX and UART_TX transfer data between data the 2 devices. UART configuration parameters, e.g. baud rate and data format, are set NF1010 firmware. When selected in firmware PIO[0] is assigned to a UART_TX output and PIO[1] is assigned to a UART_RX input, see Section 2.2. The UART CTS and RTS signals can be assigned ti any PIO pin by nFore firmware. Table shows the possible UART setting for NF1010 Possible UART Setting UART Configuration While in Deep Sleep The maximum baud rate is 9600 baud rate deep sleep. 9 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 3 MODULE SPECIFICATION 3.1 Electrical Characteristics Absolute Maximum Rating Rating Storage temperature VDD_BT_3V3 VDD_PADS Recommended Operating Conditions Operating condition Operating temperature range VDD_S_3V3 VDD_PADS Power consumption Operating condition Min VDD_S_3V3 TBD VDD_PADS TBD RF parameters Operating condition Min Transmitter 0 dBm Receiver Sensitivity -85 dBm Min -40℃ 1.8V -0.4V Max +85℃ 4.8V 3.6V Min -30℃ 1.8V 1.2V Max +85℃ 3.6V 3.6V Typ. TBD TBD Typ. 4 dBm -80dBm Max TBD TBD Max 6.5 dBm -70dBm 10 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 3.2 RF Characteristic NF1010 Module contains balun which provides a single-ended RF TX/RX port pin. No matching components are needed as the receive mode impedance is 50 Ohm and the transmitter has been optimized to deliver power in to a 50 Ohm load. The internal PA has maximum 7.5dBm output power without needing an external RF PA. 11 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 4 MECHANICAL CHARACTERISTICS NF1010 Top View and Bottom View Side 12 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 NF1010 Footprint Layout Guide (Bottom View) Stencil Fabrication must be smaller than above Footprint Layout Guide. Refer to SA-HRD-031(Stencil Design Guidelines for nFore Customer) for Stencil Fabrication. 13 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 5 SMT and Baking Recommendation 5.1 Baking Recommendation Baking condition： -Follow MSL Level 4 to do baking process. -After bag is opened, devices that will be subjected to reflow solder or other high temperature process must be a) Mounted within 72 hours of factory conditions <30°C/60% RH, or b) Stored at <10% RH. -Devices require bake, before mounting, if Humidity Indicator Card reads >10% If baking is required, Devices may be baked for 4 hrs at 100 °C. 5.2 SMT Recommendation Recommended Reflow profile： 14 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential nFore Technology Co., Ltd. Bluetooth v4.0 Module – NF1010E Hardware Specification Data Sheet v0.2 Note: (1) Reflow soldering is recommended two times maximum. (2) Add Nitrogen while Reflow process： SMT solder ability will be better. 5.3 Ordering Information The NF1010E may be ordered as follows: ■ NF1010E (2.4GHz, Stamp-27) 15 The information contained herein is the exclusive property of nFore Technology Co., Ltd. and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of nFore Technology Co., Ltd. nFore Confidential