TECHNICAL NOTE High performance video signal switcher Five inputs Dual Circuits Video Signal Switchers BA7626F/FS ●Description The BA7626F/FS is a 5-input video signal switching circuit with a broadband 6 dB amplifier that was developed for AV amplifier input switching. Just by devising a transistor buffer in the output, player switching of two VCR or other videotape players and three DVD players or other playback devices is possible. Moreover, input switching and switching of recording to a VCR or other device also can be performed independently. Since the input circuit of the BA7626F/FS is terminated by 20kΩ impedance, it is suited to not only video signal but also chroma signal or audio signal switching. ●Features 1) 5 input line, 3 output line switching 2) Built-in 6 dB amplifier 3) 5V operating voltage 4) 20kΩ input impedance ●Use AV amplifiers, Video selectors, etc. ●Lineup Part No. Package Input type BA7626F BA7626FS SOP16 SSOP-A16 Bias (R=20kΩ) ●Absolute Maximum Ratings(Ta=25℃) Parameter Supply voltage Power dissipation Symbol Vcc BA7626F Pd BA7626FS Operating temperature Topr Limits 9 300 ※1 600 ※2 -25～+70 Unit V mW ℃ Storage temperature Tstg -55～+125 ℃ ※1 Deratings is done at 3.0mW/℃ above Ta=25℃.（BA7626F） ※2 Deratings is done at 6.0mW/℃ above Ta=25℃.（BA7626FS） ●Operating Range(Ta=25℃) Parameter Power supply voltage Symbol Vcc Min 4.5 Typ 5.0 Max 5.5 Unit V Aug.2008 ●Electrical characteristics (Unless otherwise noted Ta=25℃, Vcc=5.0V) Parameter Symbol Min. Typ. Max. Circuit current ICC ― 15.0 20.0 Maximum BA7626F/FS 2.3 2.5 ― Vom output level Voltage gain GV 5.7 6.2 6.7 Interchannel crosstalk GT ― -65 -45 Mute level CTM ― -35 -25 Frequency characteristic Gf -3 0 +3 Input inpedance ZIN 16 20 24 CTL pin switching level VTH 2.2 ― 3.3 ※ This product is not designed for protection against radioactive rays. ●Truth table Input Output A B E MONOUT L L ※ IN1 H L ※ IN2 L H ※ IN3 H H L IN4 H H H IN5 ※ Indicates “don’t care”(H or L) C L H L H H Input D L L H H H Output VOUT1 － IN2 IN3 IN4 IN5 E ※ ※ ※ L H C L H L H H Input D L L H H H Unit mA Conditions ― Vp-p f=1kHz, THD=0.5% dB dB dB dB kΩ V f=1MHz, VIN=1Vp-p f=4.43MHz, VIN=1Vp-p f=4.43MHz, VIN=1Vp-p 10MHz/1MHz, VIN=1Vp-p ― Output VOUT2 IN1 － IN3 IN4 IN5 E ※ ※ ※ L H VCC 100 ●Block diagram GND 2 IN5 3 6dB logic 15 CTL A FRONT 14 VOUT1 1 MONOUT 2 GND IN1 + 16 CTL A 15 VCC 100 AUX + 3 IN5 VOUT1 4 REAR IN4 5 CTL E 6 6dB logic 12 IN2 BS 7 + CTL D 8 9 5 6 11 CTL B 10 VOUT2 VCC 13 IN4 IN2 12 75 CTL E CTL B 11 103 + 7 IN3 VOUT2 10 8 CTL D CTL C 9 + 5.0V + 47μ 2.2 + VCC 100 470μ OUT 75 + 2.2μ LD IN3 GND 2.2μ VTR IN1 75 14 A933 13 VCC OUT 75 470μ + 2.2μ 75 GND 4 TV 75 2.2 16 IN1 MONOUT 1 470μ + ●Application circuit 75 VTR IN2 75 CTL C F/R CTL Fig.1 REC CTL Fig.2 MON CTL ●Cautions on use 1) Numbers and data in entries are representative design values and are not guaranteed values of the items. 2) Although we are confident in recommending the sample application circuits, carefully check their characteristics further when using them. When modifying externally attached component constants before use, determine them so that they have sufficient margins by taking into account variations in externally attached components and the Rohm LSI, not only for static characteristics but also including transient characteristics. 3) Absolute maximum ratings If applied voltage, operating temperature range, or other absolute maximum ratings are exceeded, the LSI may be damaged. Do not apply voltages or temperatures that exceed the absolute maximum ratings. If you think of a case in which absolute maximum ratings are exceeded, enforce fuses or other physical safety measures and investigate how not to apply the conditions under which absolute maximum ratings are exceeded to the LSI. 4) GND potential Make the GND pin voltage such that it is the lowest voltage even when operating below it. Actually confirm that the voltage of each pin does not become a lower voltage than the GND pin, including transient phenomena. 5) Thermal design Perform thermal design in which there are adequate margins by taking into account the allowable power dissipation in actual states of use. 6) Shorts between pins and misinstallation When mounting the LSI on a board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is misinstalled and the power is turned on, the LSI may be damaged. It also may be damaged if it is shorted by a foreign substance coming between pins of the LSI or between a pin and a power supply or a pin and a GND. 7) Operation in strong magnetic fields Adequately evaluate use in a strong magnetic field, since there is a possibility of malfunction. 2/4 ●Pin descriptions（Ta=25℃, VCC=5V） Pin No. Equivalent circuit BA7626F/FS Pin name IN VCC 3 5 7 12 16 IN5 IN4 IN3 IN2 IN1 QN 200 QN 20k QN 4.3V 100μA 30k CTL VCC 6 8 9 11 15 CTL E CTL D CTL C CTL B CTL A 50k 50k 2k QN D QP 30k VCC 17k QN3 100 QN20 1 MONOUT MONOUT QN2 QN QN6 VCC QN5 10 VOUT2 VOUT1 14 200μA 40k 100 QN20 D VOUT 600μA QN QN15 ●Selection of order type B A 7 6 ２ ６ F Part. No. BA7626F BA7626FS E 2 Tape and Reel information BA7626F…E2(Embossed carrier tape) BA7626FS…E2(Embossed carrier tape) 3/4 SOP16 <Dimension> <Tape and Reel information> 1.5±0.1 9 1 8 4.4±0.2 2500pcs E2 Direction of feed 0.3Min. 16 Embossed carrier tape (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 0.15±0.1 0.1 1234 1234 1Pin Direction of feed Reel (Unit:mm) 1234 1234 1234 1234 0.4±0.1 1234 1.27 1234 0.11 6.2±0.3 10.0±0.2 Tape Quantity ※When you order , please order in times the amount of package quantity. SSOP-A16 <Tape and Reel information> <Dimension> 1 8 2500pcs Direction of feed E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 0.15±0.1 0.1 1234 1234 1234 1pin 1234 （Unit:mm) 1234 Reel 1234 0.36±0.1 1234 0.8 Embossed carrier tape Quantity 1234 1.5±0.1 4.4±0.2 0.11 6.2±0.3 9 0.3Min. 6.6±0.2 16 Tape Direction of feed ※When you order , please order in times the amount of package quantity. Catalog No.08T296A '08.8 ROHM © Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0