TI Smartphone Solutions TI’s extensive product portfolio delivers the performance level needed in your new smartphone project. We help you to build innovative, efficient and affordable designs, getting you to market faster. www.ti.com/smartphone 2014 Doing More Together with Mobile Handsets TI has an extensive portfolio of analog solutions designed to meet the growing demand for high-performance features in tomorrow’s smartphone market. From portable power solutions, including PMUs, DC/DC converters, RF power, backlighting, flashlight and battery management to signal-chain solutions that include audio, haptics, interface, sensors, clocking solutions and much more! The following selection guide is a sampling of TI devices that are readily available to streamline your design process. Sensors 3 G data Audio Subsystem Stereo Headphone Temperature Sensor Connectivity WiFi Amplifiers Sensor aggregation hub GNSS Audio Switches and ESD Bluetooth® ESD Audio Codec SDIO Display Subsystem Optional Haptics System I2S I2C/SPI Microphone Video AFE Accel / Compass / Gyro RF PA Power Speaker CCD/CMOS Camera Light/Proximity sensor SAR Proximity Camera Interface I2C Touch Screen Controller Applications Processor CSI DSS WLED Camera Flash Driver LPDDR Memory SDRC eMMC MMC MMC SD Card I2C Power Management Unit for System Processor and System Power Display Bias and Backlighting LCD/ AMOLED Display Display Interface Power Management Battery Charger USB Switches and ESD Gas Gauge Battery Management Peripheral and Input Power Connection Control/GPIO Voltage Translaters ESD and EMI Protection Switches Multiplexers and Logic Load Switch Solutions for Smartphone Host and Output Power Connection (Optional) Battery Battery Pack Low-Noise Power System Power Power MOSFET/ FemtoFET™ Wireless Power Receiver AC Power Adaptor Wireless Power AC Plug LEGEND Processor Interface RF/IF Amplifier Logic Power ADC/DAC Clocks Other For more information: www.ti.com/smartphone TI Solutions for Smartphones 2 Texas Instruments 2014 New products are listed in bold red. Preview products are listed in bold teal. Selection Guide Power Management Solutions Device Description Device bq24157/8 bq24250 bq27421-G1 bq27530-G1 bq27531-G1 bq24160 bq27741-G1 bq24250 bq27530-G1 bq2426x bq24195 bq27620 TPS65200 TPS65831 Fully integrated switch mode one-cell Li-Ion xharger with full USB compliance Low-cost switch-mode charger, single input, with Power Path, 1.5A / 2.5A, 1S System-side fuel gauge with integrated sense resistor / battery gas gauge System-side Impedance Track™ fuel gauge with direct battery connection Battery management unit (BMU) Impedance Track fuel gauge for bq2419x charger controllers 2.5A, dual-input, single-cell switchmode Li-Ion battery charger with power path Pack-side Impedance Track fuel gauge with integrated protector Low-cost switch-mode charger, single input, with power path, 1.5A / 2.5A, 1S System-side Impedance Track fuel gauge with direct battery connection Switch-mode charger, single input, OTG, 3A, 1S Fully integrated switch-mode NVDC-1 USB / adaptor charger, OTG, 2.5A / 4.5A, 1S Fuel-gauge, next-generation Impedance Track technology, integrated 5Vin LDO, 2.6x2mm CSP Frontend PMU with switchmode charger, WLED driver and currentshunt monitor Frontend PMU with switchmode charger, WLED driver and flash light LM3530 TPS61158 TPS61311 TPS61325 LM3630 TPS61162/3 TPS61161 LM3533 CSD16301Q2 CSD17313Q2 CSD23201W10 CSD25302Q2 CSD75205W1015 CSD13381F4 CSD25481F4 CSD13382F4 CSD23382F4 LP5900/7 TLV716 TLV707 TPS7A37 TLV713 TLV711 LP5900/4 30V N-channel FemtoFET™ MOSFET 30V N-Channel FemtoFET MOSFET 12V P-Channel FemtoFET MOSFET 20V P-Channel FemtoFET MOSFET NexFET™ N-channel in a compact SON 2x2mm package minimizes losses NexFET N-channel in a compact SON 2x2mm package minimizes losses NexFET P-channel with low ON resistance and gate charge in 1x1mm CSP package with a 0.62mm profile NexFET P-channel with lowest ON resistance and gate charge in an ultra-low profile SON 2x2mm package Dual P-channel in common source configuration and gate charge in 1x1.5mm CSP package 12V N-channel FemtoFET MOSFET 20V P-channel FemtoFET MOSFET 12V N-channel FemtoFET MOSFET 12V P-channel FemtoFET MOSFET TLV707085 TLV7111233 TPS3421 TPS3839 TPS3421 TPS3839 TLV809 TPS3831 LM3552/56/59/60 LM2754/58/59 LM3642 LM3554/9/60 Low Iq, 250nA, dual-channel push button controller in 1x1.5mm Low Iq, 150nA, supervisor in 1x1mm 3-pin supply voltage supervisor Ultra-low 150nA, ultra-small voltage supervisor Power Adapters UCC28740 Quasi-resonant current-mode flyback controller with <10mW standby power CVCC flyback controller with opto-coupler feedback and <10mW standby power UCC28700 CVCC flyback with primary-side control and <30mW no-load power UCC28710 CVCC flyback with primary-side control and <10mW no-load power UCC24610 GREEN Rectifier™ synchronous rectifier controller for 5V USB adapters LM5023 LCD bias driver with 80mA, dual output with one inductor AMOLED driver, displays below 5.5”, 300mA, digitally adjustable Vneg Triple outputs AMOLED display power supply New products are listed in bold red. Preview products are listed in bold teal. Camera Flash TPS61050 Ultra-low-noise, 150mA / 250mA linear regulator, bypass capacitor not required Capacitor-free, dual, 150mA LDO in 1.2x1.2mm SON 200mA single-output LDO, 70dB PSRR; 25µA Iq, with or without active output discharge 1% high accuracy, 1A LDO in 2x2mm SON 150mA cap-less LDO with foldback current limit in 1x1mm SON and SOT23-5 2 x 200mA dual output LDO, 48µVrms noise without bypass cap, dedicated enables Ultra-low-noise, 150mA / 200mA linear regulator, bypass capacitor not required 200mA single output LDO, 70dB PSRR; 25µA Iq 2 x 200mA dual output LDO, 48µVrms noise without bypass cap, dedicated enables Low Iq, 250nA, dual-channel push button controller in 1x1.5mm Low Iq, 150nA, supervisor in 1x1mm Reset ICs Display Bias TPS65132 TPS65631 TPS65632 High-efficiency white LED driver with programmable ambient light sensing capability 30V WLED driver with integrated power 1.5A multiple LED camera flash driver with I2C compatible interface 1.5A / 4.1A multiple LED camera flash driver with I2C interface and extended high-current Dual-string WLED backlight driver with I2C linear / exponential dimming control, CABC support, up to 20 LEDs 2x channel WLED with PWM input, 4.7µH inductor Single-String WLED backlight driver with PWM dimming control, up to 10 LEDs Dual-string WLED backlight driver with I2C linear / exponential dimming control, CABC support, up to 20 LEDs plus 5 additional LED sinks for blinking Line Regulator Power MOSFETs CSD17381F4 CSD17483F4 CSD23381F4 CSD25483F4 Description LCD Backlight Battery Management 1 LED,1A WLED driver camera flash and video light driver with I2C interface and voltage mode selection pin 1A to 2A single and dual WLED drivers for camera flash and video light driver with I2C interface and HW reset input Switched capacitor flash WLED drivers 1.5A WLED flash driver with I2C, IVFM, flash timeout and TX interupt 1.4A / 1.8A / 2.0A dual WLED flash drivers with I2C, IVFM, flash timeout and TX interupt For more information: www.ti.com/smartphone TI Solutions for Smartphones 3 Texas Instruments 2014 Selection Guide Power Management Solutions Device Description Device Description Power for HDMI, Wireless Connectivity, Memory USB Switches TPS63025 Buck-boost with 4A current switch in WCSP TPS2500/1 USB power switch with boost converter for 1.1A load current and fast current limit TPS61281 Boost bypass in WCSP package TPS2552/3 USB 3.0 power switch with +/-6% current limiting accuracy at 1.3A amplifiers: 5V boost converter with up to 3.1A switch current TPS61253/54/56/59 Power limit, up to 93% efficient – mono / stereo Class-D amplifier HDMI Power: 5V, 700mA switch current limit, 3.5MHz, 91% efficinecy, TPS61240/1 boost converter Processor Power TPS62387A Single-rail, 8A multiphase DC/DC converter TPS650380 Triple buck with multiphase, up to 6.8A TPS62650/ 66x0/ 675 0.5A / 0.8A / 1A, 6MHz synchronous buck with I2C / DVS in WCSP TPS62366A 4A buck with I2C / DVS and remote sensing, in 2x2mm WCSP TPS65913 Cortex A15 processor PMU for smartphones TPS82670 0.5A to 0.8A fully integrated, low-noise buck in MicroSiP™ package TPS81256 3W fully integrated, low-noise boost in MicroSiP package TPS62693 TPS63050 High-efficient 800mA buck (2.85V) for SDx supply in 1.2x0.9mm WCSP package Buck-boost converter with 1A / 4A current switch, 2.4MHz, up to 96% efficiency, QFN Single inductor buck-boost with 1A switches, adjustable soft start and selectable input current limit TPS63036 1A buck-boost converter, 2MHz, 1.8x1mm WCSP TPS62080 1.2A high-efficient step-down converter in 2x2mm SON package, with adjustable Vout LM3269 TPS62560 2.25MHz 600mA step-down converter in 2x2mm SON package LM3263 TLV62065 3MHz 2A step-down converter in 2x2mm SON package LM3262 TPS63020 RF PA DCDC Power LM3248 LM3290/1 Power/Load Switches TPS22908 TPS22912/13 TPS22921/22/22B TPS22964C 3A load switch with level shift and adjustable slew-rate control TPS22924B/C TPS2500/1 Ultra-small, 3.6V / 2A load switches with 18.3mΩ ON-resistance, quick output discharge and controlled turn-ON in WCSP-6 USB power switch with boost Converter for 1.1A load current and fast current limit TPS2552/3 USB 3.0 power switch with +/-6% current limiting accuracy at 1.3A LMH2121 3GHz fast responding linear power detector with 40dB dynamic range LM3241/2 Ultra-small, 3.6V / 1A load switch with 28mΩ ON-resistance, 0.19µA quiescent current, quick output discharge and controlled turn-ON in WCSP-4 Ultra-small, 5.5V / 2A load switches with 60mΩ ON-resistance, reverse current protection, and controlled turn-ON in WCSP-4 Integrated 3.6V load switches with 2A max current and 0.8µA standby current in tiny WCSP-6 package Ultra-small, 5.5V / 3A load switch with 18mΩ ON-resistance, reverse current protection, ON pin hysterisis and quick output discharge in WCSP-6 TPS27081A TPS657120 Adjustable boost-buck RF DC/DC converter RF power envelope modulator for power amplifiers 2.4MHz, seamless transition buck-boost converter for LTE and HSPA+ with PFM mode High-current step-down DC/DC converter with MIPI® RF front-end control interface for RF PAs 800mA miniature, 2.5V to 5.5V adjustable, step-down DC/DC Converter with auto bypass for RF power amplifiers 6MHz, 750mA, step-down DC/DC converter for 3G / 4G PAs, with auto bypass (only LM3242) 2.7MHz, high-current step-down DC/DC Converter with analog current bypass mode for 2G/3G/4G RF PA Buck-boost converter with MIPI RFFE interface for 3G and 4G RF Power Amplifiers RF frontend PMU LM3243 LM3279 Wireless Power Receivers BQ51013B Integrated wireless power receiver with 5V regulated output BQ51050B Integrated wireless power receiver and direct Li-Ion charger with 4.2V regulated output Integrated wireless power receiver and direct Li-Ion charger with 4.35V regulated output BQ51051B For more information: www.ti.com/smartphone TI Solutions for Smartphones 4 Texas Instruments 2014 Selection Guide Signal Chain Solutions Device Description Device Audio Codecs, DACs and Amplifiers LM49251 LM48557 TLV320AIC3262 TPA2011D1 TPA2080D1 LM48580 LM48560 TLV320AIC3212 TAS2521 TAS2505 TPA2025D1 Stereo audio subsystem with Class-G headphone amplifier and Class-D speaker amplifier with ALC-based speaker protection Mono, bridge-tied load, ceramic speaker driver with I2C volume control and reset Low-power stereo codec with miniDSP, three audio interfaces, DirectPath™ headphone and stereo Class-D speaker amplifier Portable speaker amplifier: 3.2W mono Class-D with auto-recovering short-circuit protection Portable speaker amplifier: 2.2W constant output power Class-D amplifier with Class-G boost converter High-efficiency Class-H, high-voltage, haptic piezo actuator / ceramic speaker driver High-voltage Class-H ceramic speaker driver with automatic level Control Low-power stereo codec with integrated Class-D speakers, earpiece driver, DirectPath Digital-input Class-D speaker amplifier with embedded miniDSP and mono headphone amplifier Digital-input Class-D speaker amplifier with audio processing and mono headphone amplifier 2W constant-output Class-D audio amplifier with adaptive boost (DC/DC) converter TS3A226E TS3A226AE Headset jack switch Autonomous audio headset switch with reduced GND switch RON and FM capability TS3A225E Autonomous audio switch with headset type detection TS3A5223 Autonomous audio switch with headset type detection TS3A26746E 2x2 crosspoint switch for audio applications USB Mutliplexers TS3USB221E TSU6721 TSU5611 TSU6111A TSU3USB3000 TSU3USB3200 ESD & EMI Protection HDMI Switches TPD1E10B09/05U06 TPD4S012/014 TPD4E101 TPD4E110 TPD1S414 TPD4EUSB30 TPD12S015A/016 TPD2F702 TPD3F303 TPS8E003 TPD4E05U06 TS3DV642 TPD5S115/16 Single-channel ESD protection in 0402 package 4-channel integrated protection devices for micro USB interface 4-channel ESD protection for SIM card interface 4-channel ESD protection for high-speed (up to 6Gbps) interface Micro USB OVP switch with ESD and surge for VBUS ESD protection for USB 3.0, eSATA and other high-speed interfaces Integrated protection device optimized for HDMI interface Integrated protection device optimized for analog audio interface 3-channel EMI filter for SIM card interface Integrated 8-channel ESD for keypad, microSD, side keys 4-channel ultra-low-capacitance IEC ESD protection diodes HDMI companion chip with 5V load switch, level-shifter and ESD clamp TS3DV421 Keypad Scanners TCA8418E TCA8424 High-speed USB 2.0 (480Mbps) 1:2 multiplexer / demultiplexer switch with single Enable Micro-USB SP3T switch with USB, UART, audio and integrated impedance detection Micro-USB SP3T switch with USB, UART, audio and integrated impedance detection Dual-SP2T micro-USB switch with integrated impedance and charger detection DPDT USB 2.0 high-speed and mobile high-definition link (MHL) (6.1GHz) switch DP3T USB 2.0 hIgh-speed and mobile high-definition link (MHL) or mobility display port (MyDP) (6.5GHz) switch 12-channel 1:2 MUX/DEMUX with1.8V compatible control and power-down mode 4-channel differential 8:16 multiplexer switch for DVI / HDMI applications I2C controlled keypad scan IC with integraed ESD protection Low-voltage 8x16 keyboard scanner with HID over I2C compliant interface DDR Switches TS3DDR32611 Interface MIPI single- and dual-channel DSI bridge to FlatLink™ singleand dual-channel LVDS supporting up to 2560x1600p60 24bpp resolutions Dual-channel MIPI DSI bridge to embedded DisplayPort supporting up SN65DSI86 to 4k2kp60 18bpp resolutions TUSB501DRF USB 3.0 single-channel redriver with equalizer SN65LVDS315 MIPI camera serial interface (CSI-1) transmitter 8-bit I2C GPIO expander with integrated 1.8V to 5.5V voltage TCA6408A translator TUSB1210/1 High-speed USB 2.0 On-the-Go capable transceiver SN65LVPE502A Dual-Ccannel USB 3.0 redriver / equalize RGB to dual-LVDS flat panel display transmitter with 1.8v and up to DS90C185/7 185MHz pixel xlock FlatLink LVDS flat-panel display transmitter with 1.8V and up to SN75LVDS83B/C 135MHz / 75MHz pixel clock RF Detectors and Clock Synthesizer LMH2110 8GHz logarithmic RMS power detector with 45dB dynamic range LMH2120 6GHz linear RMS power detector with 40dB dynamic range LMH2121 3GHz fast-responding linear power detector with 40dB dynamic range 50MHz to 4GHz 40dB logarithmic power Detector for CDMA and LMH2100 WCDMA 50MHz to 3.5GHz 40dB logarithmic power detector for CDMA and LMV221 WCDMA in LLP package SN65DSI83/84/85 TI Solutions for Smartphones Description Audio Switches 5 1A peak sink / source PCDDR3 termination regulator with isolation switches 12-channel, 1:2 MUX / DEMUX switch for DDR3 applications TS3DDR3812 Logic SN74AUP1G08, AND gate SN74LVC1G08 SN74LVC1G32, OR gate SN74AUP1G32 SN74AUC1G126, Buffer SN74AUP1G125 SN74AUP1G04, Inverter SN74LVC1G04 SN74LVC1G07 Buffer / driver SN74LVC1G123 Multivibrator SN74LVC2G66, Analog switch SN74LV4066 Temperature Sensors TMP104 Digital temperature sensor with one-wire interface Low-power digital temperature sensor with SMBus / two-wire TMP102 serial interface in SOT563 Ultra-small, 3μA (max) local temperature sensor with multipleTMP103 device access Dynamically programmable temperature limit window and TMP108 under-/over-temperature ALERT interrupt TMP006 Complete single-chip local and IR thermopile sensor in WCSP Dual-gain analog temperature sensor with Class-AB output in LM94023 micro SMD TMP105/06 Local temperature sensors in SOT-563 and WCSP For more information: www.ti.com/smartphone Texas Instruments 2014 Selection Guide Signal Chain Solutions Device Description Haptics Drivers DRV2665 DRV2667 DRV2668 DRV2603 DRV2604 DRV2605 Sensor Hub MSP430F5259 MSP430F5528 MSP430F5229 MSP430G2553 Piezo haptic driver with integrated boost converter and digital front end Piezo haptic driver with boost, digital front end and internal waveform memory Piezo haptic driver with boost, digital front end and internal waveform memory Haptic driver with auto resonance tracking for LRA and optimized drive for ERM Haptic driver for ERM / LRA with waveform memory and smart loop architecture Haptic driver for ERM / LRA with built-in library and smart loop architecture Ultra-low-power MSP430™ sensor hub with 4xI2C ports and 32K RAM Ultra-low-power MSP430 sensor hub with USB Ultra-low-power MSP430 sensor hub with I2C Ultra-low-power MSP430 for SAR / proximity sensing and capacitive Touch Device Description Voltage Translators TXS02324/6, Single / dual SIM card interface voltage translators TXS4555/8 TXS0206-29, MMC, SD card, memory stick interface voltage translator TXS0206A TXS0102/TXS0104E 2-bit/4-bit bidirectional open-drain application 4-bit bidirectional auto-direction sensing translator with fully TXB0304 symmetric 0.9V to 3.6V range sensing 8-bit voltage translators for display TXB0108/TXS0108E Auto-direction applications Dual bidirectional I2C bus and SMBus voltage translator with TCA9406 1MHz support and 8kV HBM ESD TXS0202 Voltage-level shifter for IC-USB interface For more information: www.ti.com/smartphone TI Worldwide Technical Support Internet Asia TI Semiconductor Product Information Center Home Page support.ti.com TI E2E™ Community Home Page e2e.ti.com Product Information Centers Americas Brazil Mexico Phone +1(512) 434-1560 Phone0800-891-2616 Phone0800-670-7544 Fax +1(972) 927-6377 Internet/Emailsupport.ti.com/sc/pic/americas.htm Europe, Middle East, and Africa Phone European Free Call 00800-ASK-TEXAS (00800 275 83927) International +49 (0) 8161 80 2121 Russian Support +7 (4) 95 98 10 701 Note: The European Free Call (Toll Free) number is not active in all c ountries. If you have technical difficulty calling the free call number, please use the international number above. Fax +(49) (0) 8161 80 2045 Internetwww.ti.com/asktexas Direct Email [email protected] Japan PhoneDomestic 0120-92-3326 Fax International+81-3-3344-5317 Domestic0120-81-0036 Internet/Email Internationalsupport.ti.com/sc/pic/japan.htm Domesticwww.tij.co.jp/pic Phone International +91-80-41381665 Domestic Toll-Free Number Note: Toll-free numbers do not support mobile and IP phones. Australia 1-800-999-084 China 800-820-8682 Hong Kong 800-96-5941 India 1-800-425-7888 Indonesia 001-803-8861-1006 Korea 080-551-2804 Malaysia 1-800-80-3973 New Zealand 0800-446-934 Philippines 1-800-765-7404 Singapore 800-886-1028 Taiwan 0800-006800 Thailand 001-800-886-0010 Fax+8621-23073686 [email protected] or [email protected] Internetsupport.ti.com/sc/pic/asia.htm Important Notice: The products and services of Texas Instruments Incorporated and its subsidiaries described herein are sold subject to TI’s standard terms and conditions of sale. Customers are advised to obtain the most current and complete information about TI products and services before placing orders. TI assumes no liability for applications assistance, customer’s applications or product designs, software performance, or infringement of patents. The publication of information regarding any other company’s products or services does not constitute TI’s approval, warranty or endorsement thereof. B090712 The platform bar, DirectPath, FlatLink, FemtoFET, NexFET, GREEN Rectifier, Impedance Track, MicroSiP and MSP430 are trademarks of Texas Instruments. All other trademarks are the property of their respective owners. Printed in U.S.A. by (Printer, City, State) © 2014 Texas Instruments Incorporated SLYY032A IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated