Eon Silicon Solution Inc. Application Note EON EN25Q80A vs Numonyx M25PE80 Specification Comparison This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 1 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. 1. INTRODUCTION The application note introduces how to implement a system design from Numonyx M25PE80 Flash to Eon EN25Q80A Flash. 2. GENERAL FUNCTION COMPARISON TABLE: 2.1 The following table highlights the major features of these two devices. Features Voltage Range SPI frequency (standard / dual / quad mode) Secured Silicon Sector Region Sector Architecture SPI mode EN25Q80A 2.7 ~ 3.6 M25PE80 2.7 ~ 3.6 100MHz (standard mode) 80MHz @ dual & quad mode 75MHz (standard mode) 256 Byte No Uniform 256 Sectors of 4 K byte 16 Blocks of 64 K byte Mode 0 / Mode 3 Uniform Subsectors of 4 K byte Sectors of 64 K byte Mode 0 / Mode 3 Yes No EQIO mode (Full Quad mode) Dual Output Fast Read Dual I/O Fast Read Quad I/O Fast Read Yes No Yes Yes No No Reset# pin Page write Page erase Lock Register No No No No Yes Yes Yes Yes Minimum Endurance Cycle 100K 100K Package 8-pins SOP 150mil / 208mil 8 contact VDFN (5x6mm) 8-pin DIP SO8W (208mil) SO8N (150mil) VFQFPN8 5x6mm (MLP8) QFN8L 5x6mm (MLP8) / exposed pad of 3x3mm This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 2 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. 3. HARDWARE CONSIDERATIONS 3.1 ICC comparison Current EN25Q80A M25PE80 Max Read ICC3 25 @ 100MHz 20 @ 80MHz Page Program (PP) ICC4 28 Max 8 @ 50MHz 6 @ 33MHZ 12 @ 75MHz (for T9HX) 4 @ 33MHZ (for T9HX) 15 Sector Erase (SE) ICC6 Block Erase (BE) ICC7 25 15 mA Standby ICC1 5 50 μA Unit mA mA 3.2 Pin Configuration Pin number Pin1 Pin2 EN25Q80A CS# DO (DQ1) Pin3 WP# (DQ2) Pin4 Pin5 Pin6 Pin7 Pin8 VSS DI (DQ0) CLK NC (DQ3) VCC M25PE80 S#(CS#) Q(DO) TSL# for T7Y process or W#(WP#) for T9HX process VSS D(DI) C(CLK) Reset# VCC Note: 1. If customers don’t use Reset# pin function on M25PE80, which can be replaced by EN25Q80A in standard SPI mode. 2. M25PE80 only support general standard SPI mode. 3. EN25Q80A can support general standard / dual / quad SPI mode. (Need specific SPI controller) This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 3 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. 4. SOFTWARE CONSIDERATIONS 4.1 Manufacturer, Memory Type & Device Identification (M7~M0: manufacture ID, D15~ID0: memory type, ID7~ID0: memory density) comparison. For EN25Q80A OP Code (M7-M0) (ID15-ID0) ABh (ID7-ID0) 13h 90h 1Ch 9Fh 1Ch 13h 3014h For M25PE80 This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 4 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. 4.2. Instruction Set Comparison 4.2.1 Different Read Status Register content EN25Q80A： S5 is reserved bit, S6 is WPDIS bit, S7 are SRP bit and OTP_LOCK bit (in OTP mode). M25PE80： This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 5 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. 4.2.2 Different Lock Register content EN25Q80A：No support. M25PE80： This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 6 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 7 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. 4.2.3 Different software protections EN25Q80A：Block protect area definitions of (BP0~BP2) M25PE80： The first software protected mode (SPM1) This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 8 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 9 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. M25PE80： The second software protected mode (SPM2) uses the block protect (BP2, BP1, BP0) 4.2.4 Enable Quad I/O (EQIO) (38h) command EN25Q80A：Support. M25PE80：No support. 4.2.5 Reset Quad I/O (RSTQIO) (FFh) command EN25Q80A：Support. M25PE80：No support. 4.2.6 Dual Output Fast Read (3Bh) commands EN25Q80A：Support. M25PE80：No support. 4.2.7 Dual Input / Output FAST_READ (BBh) commands EN25Q80A：Support. M25PE80：No support. This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 10 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. 4.2.8 Quad Input / Output FAST_READ (EBh) commands EN25Q80A：Support. M25PE80：No support. 4.2.9 Manufacturer/ Device ID (90h) commands EN25Q80A：Support. M25PE80：No support. 4.2.10 Enter OTP Mode (3Ah) commands EN25Q80A：Support. OTP Sector Address M25PE80：No support. 4.2.11 Write to lock register (E5h) commands EN25Q80A：No support. M25PE80： Support. 4.2.12 Read lock register (E8h) commands EN25Q80A：No support. M25PE80： Support. 4.2.13 Page write (0Ah) commands EN25Q80A：No support. M25PE80： Support. 4.2.14 Page erase (DBh) commands EN25Q80A：No support. M25PE80： Support. This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 11 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. 5. PERFORMANCE DIFFERENCES 5.1 ERASE AND PROGRAM PERFORMANCE The erasing and programming performance comparison. EN25Q80A Parameter M25PE80 (75MHz, T9XH) Typ Max Unit Typ Max Page Programming Time 1.3 5 0.8 3 ms 4 KB Sector Erase Time 0.09 0.3 0.05 0.15 sec 64KB Block Erase Time 0.5 2 1 5 sec Chip (Bulk) Erase Time 8 20 10 60 sec 5.2 KEY AC PARAMETER PERFORMANCE EN25Q80A M25PE80 (75MHz, T9XH) tCH (serial clock high time) Min @ 4ns Min @ 6ns tCL (serial clock low time) Min @ 4ns Min @ 6ns tCLCH(serial clock rise time) Min @ 0.1V / ns Min @ 0.1V / ns tCLCL(serial clock fall time) Min @ 0.1V / ns Min @ 0.1V / ns Min@ 5ns Min @ 5ns Parameter tCHSH(CS# active setup / hold time) tSHSL(CS# high time) Min @ 15ns for Read Min @ 50ns for Write Min @ 100ns tDSU(Data in setup time) Min @ 2ns Min @ 2ns tDH(Data in hold time) Min @ 5ns Min @ 5ns This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 12 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com Eon Silicon Solution Inc. Revisions List Revision No Description Date A 2010/05/11 Initial Release This Application Note may be revised by subsequent versions or modifications due to changes in technical specifications. 13 ©2005 Eon Silicon Solution Inc. Rev. A, Issue Date: 2010/ 05/11 www.eonssi.com