TransGuard ® PACKAGING • Chips • Axial Leads 98 Paper Carrier Configuration 8mm Tape Only 10 PITCHES CUMULATIVE TOLERANCE ON TAPE ±0.20mm (±0.008) P0 D0 T P2 E1 BOTTOM COVER TAPE TOP COVER TAPE F W E2 B0 G T1 T1 A0 CENTER LINES OF CAVITY CAVITY SIZE SEE NOTE 1 P1 User Direction of Feed 8mm Paper Tape Metric Dimensions Will Govern CONSTANT DIMENSIONS Tape Size 8mm D0 -0.0 1.50 +0.10 (0.059 +0.004 -0.0 ) mm (inches) E P0 P2 1.75 ± 0.10 4.00 ± 0.10 2.00 ± 0.05 (0.069 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.002) T1 G. Min. R Min. 0.10 (0.004) Max. 0.75 (0.030) Min. 25.0 (0.984) See Note 2 Min. VARIABLE DIMENSIONS Tape Size 8mm P1 See Note 4 4.00 ± 0.10 (0.157 ± 0.004) mm (inches) E2 Min. 6.25 (0.246) F W 3.50 ± 0.05 (0.138 ± 0.002) 8.00 +0.30 -0.10 (0.315 +0.012 -0.004 ) A0 B0 T See Note 1 1.10mm (0.043) Max. for Paper Base Tape and 1.60mm (0.063) Max. for Non-Paper Base Compositions NOTES: 1. The cavity defined by A0, B0, and T shall be configured to provide sufficient clearance surrounding the component so that: a) the component does not protrude beyond either surface of the carrier tape; b) the component can be removed from the cavity in a vertical direction without mechanical restriction after the top cover tape has been removed; c) rotation of the component is limited to 20º maximum (see Sketches A & B); d) lateral movement of the component is restricted to 0.5mm maximum (see Sketch C). 2. Tape with or without components shall pass around radius “R” without damage. 3. Bar code labeling (if required) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556. 4. If P1 = 2.0mm, the tape may not properly index in all tape feeders. Top View, Sketch "C"� Component Lateral 0.50mm (0.020) Maximum 0.50mm (0.020) Maximum Bar Code Labeling Standard AVX bar code labeling is available and follows latest version of EIA-556 99 Embossed Carrier Configuration 8 & 12mm Tape Only 10 PITCHES CUMULATIVE TOLERANCE ON TAPE ±0.2mm (±0.008) EMBOSSMENT P0 T2 T D0 P2 DEFORMATION BETWEEN EMBOSSMENTS E1 A0 F TOP COVER TAPE B1 T1 W B0 K0 S1 E2 CENTER LINES OF CAVITY P1 MAX. CAVITY SIZE - SEE NOTE 1 B1 IS FOR TAPE READER REFERENCE ONLY INCLUDING DRAFT CONCENTRIC AROUND B0 D1 FOR COMPONENTS 2.00 mm x 1.20 mm AND LARGER (0.079 x 0.047) User Direction of Feed 8 & 12mm Embossed Tape Metric Dimensions Will Govern CONSTANT DIMENSIONS Tape Size D0 8mm and 12mm 1.50 +0.10 -0.0 -0.0 (0.059 +0.004 ) mm (inches) E P0 P2 1.75 ± 0.10 4.0 ± 0.10 2.0 ± 0.05 (0.069 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.002) S1 Min. T Max. T1 0.60 (0.024) 0.60 (0.024) 0.10 (0.004) Max. VARIABLE DIMENSIONS Tape Size B1 Max. D1 Min. E2 Min. mm (inches) F P1 See Note 5 R Min. See Note 2 T2 W Max. A0 B0 K0 8mm 4.35 (0.171) 1.00 (0.039) 6.25 (0.246) 3.50 ± 0.05 4.00 ± 0.10 (0.138 ± 0.002) (0.157 ± 0.004) 25.0 (0.984) 2.50 Max. (0.098) 8.30 (0.327) See Note 1 12mm 8.20 (0.323) 1.50 (0.059) 10.25 (0.404) 5.50 ± 0.05 4.00 ± 0.10 (0.217 ± 0.002) (0.157 ± 0.004) 30.0 (1.181) 6.50 Max. (0.256) 12.3 (0.484) See Note 1 NOTES: 1. The cavity defined by A0, B0, and K0 shall be configured to provide the following: Surround the component with sufficient clearance such that: a) the component does not protrude beyond the sealing plane of the cover tape. b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the cover tape has been removed. c) rotation of the component is limited to 20º maximum (see Sketches D & E). d) lateral movement of the component is restricted to 0.5mm maximum (see Sketch F). 2. Tape with or without components shall pass around radius “R” without damage. 3. Bar code labeling (if required) shall be on the side of the reel opposite the round sprocket holes. Refer to EIA-556. 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. If P1 = 2.0mm, the tape may not properly index in all tape feeders. Top View, Sketch "F"� Component Lateral Movements 0.50mm (0.020) Maximum 0.50mm (0.020) Maximum 100 Packaging of Chip Components Automatic Insertion Packaging REEL DIMENSIONS mm (inches) Tape Size A Max. B* Min. C D* Min. N Min. 8mm 330 (12.992) 1.5 (0.059) 13.0 +0.50 -0.20 (0.512 +0.020 -0.008 ) 12mm 20.2 (0.795) W1 W2 Max. W3 8.40 +1.5 -0.0 -0.0 (0.331 +0.059 ) 14.4 (0.567) 7.90 Min. (0.311) 10.9 Max. (0.429) 12.4 +2.0 -0.0 -0.0 (0.488 +0.079 ) 18.4 (0.724) 11.9 Min. (0.469) 15.4 Max. (0.607) 50.0 (1.969) Metric dimensions will govern. English measurements rounded and for reference only. 101 TransGuard® AVX Multilayer Ceramic Transient Voltage Suppressors PACKAGING - AXIAL LEADS / TAPE AND REEL CLASS I / RS-296 5mm ± 0.5mm (0.200" ± 0.020") 52.4mm ± 1.5mm (2.063" ± 0.059") 6.35mm ± 0.4mm (0.250" ± 0.016") 1.4mm (0.055" MAX.) 1.2mm (0.047" MAX.) 1.6mm (0.063" MAX.) 356mm (14.00" MAX.) 76mm (3.000") 25.4mm (1.000") 84mm (3.300") 70mm (2.750") A. B*. C. D1-D2. E. F. G. H. I. J. K. Optional Design H D1 F C E A B K Leader Tape: 300mm min. (12") Splicing: Tape Only Missing Parts: 0.25% of component count max.No consecutive missing parts J I G 102 D2