Future Technology Devices International Ltd. FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Datasheet Document Reference No.: FT_000114 Version 1.7 Issue Date: 2012-07-09 Future Technology Devices International Ltd (FTDI) Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminar y information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © 2011 Future Technology Devices International Limited Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` 1 Introduction The FT2232H Mini Module is a USB-to-serial/FIFO development module in the FTDI product range which utilizes the FT2232H USB Hi-Speed two-port bridge chip which handles all the USB signalling and protocols. It is ideal for development purposes to quickly prove functionality of adding USB to a target design. The FT2232H datasheet, DS_FT2232H, is available at http://www.ftdichip.com, Figure 1.1 - FT2232H Mini Module The FT2232H on the Mini Module is FTDI’s 5th generation of USB devices. The FT2232H is a USB 2.0 High Speed (480Mb/s) to UART/MPSSE IC. The device features two interfaces that can be configured for asynchronous or synchronous serial or parallel FIFO interfaces. The two channels can also be independently configured to use an MPSSE engine. This allows the two ports of the FT2232H to operate independently as UART/Bit-Bang ports or MPSSE engines used to emulate JTAG, SPI, I2C, Bit-bang or other synchronous serial modes. All components used, including the FT2232H are Pb-free (RoHS compliant). The FT2232H Mini Module connects the signals of the FT2232H IC to two 26-pin dual-row headers which allow easy connection PCB header sockets and ribbon cables. The FT2232H Mini Module requires USB device drivers, available free from http://www.ftdichip.com, which are used to make the FT2232H on the Mini Module appear as a two virtual COM ports (VCP). This then allows the user to communicate with the USB interface via a standard PC serial emulation port (TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT2232H on the Mini Module though a DLL. This is illustrated in the Figure 1.2 VCP TTY USB Virtual COM Port DLL D2XX TTY One RXD Channel of USB Mini-B FT2232H Mini Module TXD Serial UART signals One RXD Channel of USB Mini-B FT2232H Mini Module TXD USB Serial UART signals Software application access to USB via D2XX Figure 1.2 Using the FT2232H Device Drivers for the FT2232H Mini Module are available free from http://www.ftdichip.com. Copyright © 2011 Future Technology Devices International Limited 1 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` 1.1 USB Compliant The FT2232H Mini Modules are fully compliant with the USB 2.0 specification. Copyright © 2011 Future Technology Devices International Limited 2 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` Table of Contents 1 Introduction .................................................................... 1 1.1 2 USB Compliant .......................................................................... 2 Typical Applications ........................................................ 4 2.1 Driver Support .......................................................................... 4 2.2 Features .................................................................................... 4 3 Electrical Details ............................................................. 5 4 Mechanical details ........................................................... 8 5 Schematic Diagram ......................................................... 9 6 Contact Information ...................................................... 10 Appendix A – FT2232H EEPROM Configuration ................................ 10 Appendix B – Revision History ......................................................... 11 Copyright © 2011 Future Technology Devices International Limited 3 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` 2 Typical Applications Rapid USB integration into existing electronic systems. Prototyping platform for USB interface on new systems. USB to multi-port JTAG, SPI and I2C interfaces (Two Multi-Protocol Synchronous Serial Engines available with the FT2232H) USB to multi-port asynchronous serial interfaces. 2.1 Driver Support Royalty free VIRTUAL COM PORT Royalty free D2XX Direct Drivers (VCP) DRIVERS for... (USB Drivers + DLL S/W Interface) Windows 2000, Server 2003, XP Server 2008 Windows 2000, Server 2003, Server 2008 Windows XP and XP 64-bit Windows XP and XP 64-bit Windows Vista and Vista 64-bit Windows Vista and Vista 64-bit Windows XP Embedded Windows XP Embedded Windows CE 4.2, 5.0, 5.2 and 6.0 Windows CE 4.2, 5.0, 5.2 and 6.0 Mac OS-X Linux (2.4 or later) and Linux x86_64 Linux (2.6.9 or later) The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - see www.ftdichip.com for details. 2.2 Features The FT2232H Mini Module has the following features: USB 2.0 Hi-Speed compatible Reduced development time Rapid integration into existing systems USB powered – no external power supply needed Based on the USB Hi-Speed FT2232H device Entire USB protocol handled by USB module Small USB Type B connector common on many commercial devices Asynchronous Serial data transfer rates from 300 baud to 12 Mbaud at TTL levels Synchronous Serial (MPSSE) data rates of up to 30Mbps on JTAG, SPI and I2C Support for USB suspend and resume UHCI / OHCI / EHCI host controller compatible -40°C to +85°C operating temperature range Copyright © 2011 Future Technology Devices International Limited 4 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` 3 Electrical Details The electrical details and connections to the FT2232H Mini Module are shown in Figure 3.1 and tables 3.1 and 3.2. 2 26 1 25 2 26 1 25 Figure 3.1 FT2232H Mini Module Electrical Connections (Top View) Connector Pin Name Description CN2-1 V3V3 3.3VDC generated from VCC (output) CN2-2 GND 0V Power pin CN2-3 V3V3 3.3VDC generated from VCC (output) CN2-4 GND 0V Power pin CN2-5 V3V3 3.3VDC generated from VCC (output) CN2-6 GND 0V Power pin CN2-7 AD0 FT2232H AD0 pin CN2-8 RESET# CN2-9 AD2 FT2232H AD2 pin CN2-10 AD1 FT2232H AD1 pin CN2-11 VIO Connected to all FT2232H VCCIO pins (input) CN2-12 AD3 FT2232H AD3 pin FT2232H RESET# pin Copyright © 2011 Future Technology Devices International Limited 5 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` CN2-13 AD5 FT2232H AD5 pin CN2-14 AD4 FT2232H AD4 pin CN2-15 AD7 FT2232H AD7 pin CN2-16 AD6 FT2232H AD6 pin CN2-17 AC1 FT2232H AC1 pin CN2-18 AC0 FT2232H AC0 pin CN2-19 AC3 FT2232H AC3pin CN2-20 AC2 FT2232H AC2 pin CN2-21 VIO Connected to all FT2232H VCCIO pins (input) CN2-22 AC4 FT2232H AC4 pin CN2-23 AC6 FT2232H AC6 pin CN2-24 AC5 FT2232H AC5 pin CN2-25 SUSPEND# CN2-26 AC7 FT2232H SUSPEND# pin FT2232H AC7 pin Table 3.1 FT2232H Mini Module Connection – CN2 Connector Pin Name Description CN3-1 VBUS USB VBUS power pin (output) CN3-2 GND 0V Power pin CN3-3 VCC CN3-4 GND CN3-5 CS FT2232H EECS pin CN3-6 CLK FT2232H EECLK pin CN3-7 DATA CN3-8 PWREN# FT2232H PWREN# CN3-9 BC7 FT2232H BC7 pin CN3-10 BC6 FT2232H BC6 pin CN3-11 BC5 FT2232H BC5 pin CN3-12 VIO Connected to all FT2232H VCCIO pins (input) CN3-13 BC4 FT2232H BC4 pin +5V Power pin (input) used to generate V3V3, VPLL and VUSB 0V Power pin FT2232H EEDATA pin Copyright © 2011 Future Technology Devices International Limited 6 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` CN3-14 BC3 FT2232H BC3 pin CN3-15 BC2 FT2232H BC2 pin CN3-16 BC1 FT2232H BC1 pin CN3-17 BC0 FT2232H BC0 pin CN3-18 BD7 FT2232H BD7 pin CN3-19 BD6 FT2232H BD6 pin CN3-20 BD5 FT2232H BD5 pin CN3-21 BD4 FT2232H BD4 pin CN3-22 VIO Connected to all FT2232H VCCIO pins (input) CN3-23 BD3 FT2232H BD3 pin CN3-24 BD2 FT2232H BD2 pin CN3-25 BD1 FT2232H BD1 pin CN3-26 BD0 FT2232H BD0 pin Table 3.2 FT2232H Mini Module Connection – CN3 In most cases, the FT2232H pin is connected directly to the associated pin on CN2 or CN3. The FT2232H Mini Module allows configuration with both USB Bus-powered and USB Self-powered designs: USB Bus-powered: 1) Connect VBUS to VCC (CN3, pin 1 to CN3, pin 3). This connection takes the power from the USB bus (VBUS) and connects it to the voltage regulator input on the FT2232H Mini Module. The voltage regulator, in turn, provides V3V3, VPLL and VUSB power inputs to the FT2232H chip. 2) Connect V3V3 to VIO (CN2, pins 1, 3 & 5 to CN2, pins 11 & 21 and CN3, pins 12 & 22). This connection provides the correct 3.3VDC operating voltage for VCCIO on the FT2232H chip. USB Self-Powered: 1) Leave VBUS (CN3, pin 1) unconnected. 2) Connect an external 5.0VDC power supply to VCC (5.0VDC to CN3, pin 3). This connection takes provides power from an external power supply and connects it to the voltage regulator input on the FT2232H Mini Module. See the FT2232H data sheet for allowable VCC input voltage ranges. 3) Connect V3V3 to VIO (CN2, pins 1, 3 & 5 to CN2, pins 11 & 21 and CN3, pins 12 & 22). This connection provides the correct 3.3VDC operating voltage for VCCIO on the FT2232H chip. 4) Use MPROG to change the USB power descriptor to “Self-Powered”. This setting indicates to the host system that the USB Host port does not need to supply power to the device. MPROG is a utility provided by FTDI to program various features of the FT-series USB client ICs. In order to access settings for the FT2232H, MPROG, version 3.5 or later is required. MPROG is available through the Utilities section of the FTDI web site. Copyright © 2011 Future Technology Devices International Limited 7 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` 4 Mechanical details The mechanical details (top view) of the FT2232H Mini Module are shown in Figure 4.1: Figure 4.1 FT2232H Mini Module Dimensions (Top and Side Views) All dimensions are in millimetres. Tolerance is ±0.1mm. The headers CN2 and CN3 are mounted to the bottom of the PCB. The overall height below the PCB is 8.5mm, with a body which exposes 6.0mm of the pins. The pins are 0.025 inch square. The mini-B USB connector has a height of 3.9mm. Copyright © 2011 Future Technology Devices International Limited 8 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` 5 Schematic Diagram Figure 5.1 FT2232H Mini Module Schematic Copyright © 2011 Future Technology Devices International Limited 9 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` 6 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] Branch Office – Hillsboro, Oregon, USA Branch Office – Shanghai, China Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 Future Technology Devices International Limited (China) Room 1103, No. 666, West Huaihai Road, Shanghai, 200052 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2011 Future Technology Devices International Limited 10 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` Appendix A – FT2232H EEPROM Configuration The FT2232H Mini Module utilizes an EEPROM which contains the USB configuration descriptors for the FT2232H. When the Mini Module is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the EEPROM are defined in Table 6.1. Parameter Value Notes USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6010h FTDI default PID (hex) Serial Number Enabled? Yes Serial Number See Note Pull down I/O Pins in USB Suspend A unique serial number is generated and programmed into the EEPROM during device final test. Enabling this option will make the device pull down on the Disabled UART interface lines when the power is shut off (PWREN# is high). Manufacturer Name FTDI Product Description FT2232H_MM Max Bus Power Current 500mA Power Source Bus Powered Device Type FT2232 Returns USB 2.0 device description to the host. USB Version 0200 Note: The device is a USB 2.0 High Speed device (480 Mb/s) as opposed to a USB 2.0 Full Speed device (12 Mb/s). Remote Wake Up Enabled High Current I/Os Enabled Load VCP Driver Disabled Taking RI# low will wake up the USB host controller from suspend. Enables the high drive level on the UART and CBUS I/O pins. Makes the device load the VCP driver interface for the device. Table 6.1 Default Internal EEPROM Configuration The EEPROM on the FT2232H Mini Module can be re-programmed over USB using the utility program MPROG. MPROG can be downloaded from the www.ftdichip.com. Version 3.5 or later is required for the FT2232H chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service. Copyright © 2011 Future Technology Devices International Limited 10 Document Reference No.: FT_000114 FT2232H Mini Module USB Hi-Speed FT2232H Evaluation Module Version 1.7 Clearance No.: FTDI#72 ` Appendix B – Revision History Version 1.0 First Release 12rd Feb 2009 Version 1.1 Corrected VIO to pins 12 and 22 in text below table 4th March 2009 Version 1.2 Changed PCB dimension from 20.32 to 29.4 23rd March 2009 Version 1.3 Corrected PCB dimensions 10th June 2009 Version 1.4 Added more PCB dimensions 25th June 2009 Version 1.5 Removed invert signals and corrected PCB dimension 11th August 2009 Version 1.6 Updated schematic diagram 26th Jan 2011 Added USB certified Logo in section 1.1 Added RoHS compliant statement in section 1 Version 1.61 Edited Appendix A, Table 6.1, USB Version Parameter 02nd Nov 2011 Version 1.7 Updated Contact Information, Figure 1.1 and 3.1 25th June 2012 Copyright © 2011 Future Technology Devices International Limited 11