aat3113/3114 data sheet - Skyworks Solutions, Inc.

DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
General Description
Features
The AAT3113 and AAT3114 are low noise, constant frequency charge pump DC/DC converters that use fractional (1.5X) conversion to increase efficiency in white
LED applications. The devices can be used to produce
current levels up to 20mA for each output from a 2.7V
to 5.5V input. A low external parts count (two 1μF flying
capacitors and two small bypass capacitors at VIN and
OUT) makes these devices ideally suited for small, battery-powered applications.
•
•
•
•
Skyworks' Simple Serial Control (S2Cwire™) interface is
used to enable, disable, and set the LED drive current for
32-level logarithmic scale LED brightness control.
AAT3113 and AAT3114 devices have a thermal management system for protection in the event of a short-circuit
condition on any of the output pins. Built-in soft-start
circuitry prevents excessive inrush current during startup. A high switching frequency enables the use of small
external capacitors. A low-current shutdown feature disconnects the load from VIN and reduces quiescent current
to less than 1μA. The AAT3113 provides four LED current
source outputs, and the AAT3114 provides six. The
AAT3113 is available in a Pb-free 12-pin TSOPJW package, and the AAT3114 is available in a Pb-free 16-pin
QFN package.
•
•
•
•
•
•
•
•
•
•
•
•
•
AAT3113: Four Outputs
AAT3114: Six Outputs
20mA Full-Scale Current
Simple Serial Control (S2Cwire) Interface
▪ 32-Position Logarithmic Scale with Digital Control
Low Noise Constant Frequency Operation
33% Less Input Current Than Doubler Charge Pump
High Accuracy Brightness Matching
Small Application Circuit
Regulated Output Current
Automatic Soft Start
VIN Range: 2.7V to 5.5V
No Inductors
600kHz Switching Frequency
IQ <1μA in Shutdown
Temperature Range: -40°C to 85°C
12-Pin TSOPJW Package (AAT3113)
16-Pin QFN Package (AAT3114)
Applications
• Programmable Current Source
• White LED Backlighting
Typical Application
VIN
VIN
C1+
C1+
C1
1µF
C1
1µF
C1C2+
OUT
VBATTERY
CIN
1µF
EN/SET
COUT
1µF
AAT3113
C2
1µF
VBATTERY
COUT
1µF
C2
1µF
AAT3114
C2-
C2-
D1
D2
D3
D4
D1
D2
D3
D4
D5
D6
EN/SET
GND
C1C2+
OUT
CIN
1µF
EN/SET
D4
D3
D2
D1
EN/SET
GND
D6
D5
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
D4
D3
D2
D1
1
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Pin Descriptions
Pin Number
AAT3114
AAT3113
Symbol
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
7
6
5
N/A
N/A
4
3
N/A
2
1
12
11
N/A
10
9
D2
D3
D4
D5
D6
C1+
C1NC
OUT
C2+
C2GND
NC
VIN
EN/SET
16
8
D1
EP
Function
Current source output 2. If not used, leave pin floating.
Current source output 3. If not used, leave pin floating.
Current source output 4. If not used, leave pin floating.
Current source output 5. If not used, leave pin floating.
Current source output 6. If not used, leave pin floating.
Flying capacitor 1 positive terminal.
Flying capacitor 1 negative terminal.
No connect.
Charge pump output. Requires 1μF bypass capacitor to ground.
Flying capacitor 2 positive terminal.
Flying capacitor 2 negative terminal.
Ground.
No connect.
Input power supply. Requires 1μF bypass capacitor to ground.
Control pin using S2Cwire serial interface.
Current source output 1. Required reference current source. Do not leave pin
floating.
Exposed paddle (bottom); connect to GND directly beneath package.
Pin Configuration
TSOPJW-12
(Top View)
AAT3113
9
5
8
6
7
D2
1
12
GND
D3
2
11
C2-
D4
3
10
C2+
D5
4
9
OUT
8
7
6
5
NC
C1-
C1+
D6
2
13
4
14
10
NC
VIN
3
C2GND
VIN
EN/SET
D1
D2
15
11
EN/SET
12
2
16
1
D1
C2+
OUT
C1C1+
D4
D3
QFN44-16
(Top View)
AAT3114
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Part Number Descriptions
Part Number
VIN Range
Number of LED Outputs,
20mA Full-Scale
LED Present
Detect Current
Package
AAT3113ITP
AAT3114ISN
3.0V  VIN  5.5V
3.2V  VIN  5.5V
4
6
150μA
150μA
TSOPJW-12
QFN44-16
Absolute Maximum Ratings
TA = 25°C, unless otherwise noted.
Symbol
VIN
VOUT
VEN/SET
VEN/SET(MAX)
IOUT
JA
TJ
Description
Input Voltage
Charge Pump Output
EN/SET to GND Voltage
Maximum EN/SET to Input Voltage
Maximum DC Output Current (sum of IOUT and D currents)
Thermal Resistance
Operating Junction Temperature Range
Value
Units
-0.3 to 6
-0.3 to 6
-0.3 to 6
0.3
150
37
-40 to 150
V
V
V
V
mA
°C/W
°C
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
3
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Electrical Characteristics
VIN = 3.5V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = 25°C.
Symbol
Description
Input Power Supply
Operation Range
VIN
ICC
Operating Current
ISHDN
Shutdown Current
IDX
Output Current
Output Current Line
Regulation
Current Matching Between
I(D-Match)
Any Two Outputs

Efficiency
Charge Pump
tSS
Soft-Start Time
FCLK
Clock Frequency
EN/SET
VEN(L)
Enable Threshold Low
VEN(H)
Enable Threshold High
tLO
EN/SET Low Time
tHI
Minimum EN/SET High Time
tOFF
EN/SET Off Timeout
Input
EN/SET Input Leakage
Current
ID/VIN
4
Conditions
Min
Typ
Max
Units
1
5.5
2
1
V
mA
μA
20
22
mA
2
%/V
2.7
Active, No Load Current
EN = 0
AAT3113: 3.0V  VIN  5.5V
AAT3114: 3.2V  VIN  5.5V
3.0V  VIN  5.5V
TA = 25°C, All Outputs
Max Current
18
-2
VD1:Dn = 3.6V, VIN = 3.3V
0.3
%
VIN = 3.5V, IOUT(total) = 40mA
93
%
300
VIN = 2.7V to 5.5V
VIN = 2.7V to 5.5V
400
600
0.5
500
1
μA
75
-1
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
μs
kHz
V
V
μs
ns
μs
1.4
0.3
50
300
VIN = 5.5V
900
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Typical Characteristics
VIN = 3.5V, CIN = COUT = C1 = C2 = 1μF; TA = 25°C, unless otherwise noted.
Efficiency vs. Supply Voltage
Quiescent Current vs. Temperature
100
0.98
95
Efficiency (%)
1.00
IQ (mA)
0.96
0.94
0.92
0.90
0.88
30mA
20mA
90
85
40mA
80
80mA
75
120mA
70
65
60
0.86
-40
-20
0
20
40
60
80
3.0
100
3.2
3.4
Temperature (°C)
3.8
4.0
4.2
4.4
Efficiency vs. Load Current
1.2
96
94
Efficiency (%)
1.1
1.0
IQ (mA)
3.6
Supply Voltage (V)
Quiescent Current vs. Supply Voltage
0.9
0.8
0.7
92
90
88
86
84
82
0.6
80
3.0
3.5
4.0
4.5
5.0
5.5
0
20
40
60
80
100
120
Load Current (mA)
Supply Voltage (V)
Oscillator Frequency vs. Temperature
Shutdown Current vs. Temperature
710
1.000
700
690
680
0.100
FOSC (kHz)
Shutdown Current (µA)
60mA
0.010
670
660
650
640
630
620
0.001
-40
-20
0
20
40
Temperature (°C)
60
80
100
610
-40
-20
0
20
40
60
80
100
Temperature (°C)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
5
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Typical Characteristics
VIN = 3.5V, CIN = COUT = C1 = C2 = 1μF; TA = 25°C, unless otherwise noted.
Normalized I DIODE vs. Temperature
IDIODE Response
(-31dB to 0dB)
1.02
1.01
ENSET
(2V/div)
IDIODE
1.00
0dB
0.99
0.98
0.97
IDIODE
0.96
-31dB
0.95
-40
-20
0
20
40
60
80
100
Time (10µs/div)
Temperature (°C)
IDIODE vs. VIN
IDIODE Response
(-9dB to -10dB)
140
ENSET
(2V/div)
IDIODE (mA)
120
100
80
0dB
-10dB
60
IDIODE
40
-9dB
20
-31dB
0
3.0
3.5
4.0
4.5
VIN (V)
Time (10µs/div)
VIH and VIL vs. VIN
140
1.000
120
0.975
0.950
VIH and VIL (V)
IDIODE (mA)
IDIODE vs. VDIODE
100
80
60
40
0.900
VIH
0.875
0.850
0.825
VIL
0.800
0.775
20
0.750
0
3.0
3.2
3.4
3.6
V DIODE (V)
6
0.925
3.8
4.0
2.5
3.0
3.5
4.0
4.5
VIN (V)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
5.0
5.5
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Typical Characteristics
VIN = 3.5V, CIN = COUT = C1 = C2 = 1μF; TA = 25°C, unless otherwise noted.
Turn-On
Turn-Off
ENSET
(2V/div)
ENSET
(2V/div)
OUT
(5V/div)
OUT
(5V/div)
VDIODE
(5V/div)
VDIODE
(2V/div)
IIN
(50mA/div)
IIN
(50mA/div)
Time (200µs/div)
Time (100µs/div)
60mA Load Characteristics
40mA Load Characteristics
IN
OUT
VDIODE
VDIODE
Time (1µs/div)
Time (1µs/div)
80mA Load Characteristics
120mA Load Characteristics
20mV/div
OUT
VDIODE
20mV/div
IN
IN
OUT
20mV/div
10mV/div
OUT
IN
VDIODE
Time (1µs/div)
Time (1µs/div)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
7
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Functional Block Diagram
VIN
Soft Start
C1+
C1-
1.5X
Charge
Pump
600kHz
Oscillator
C2+
C2-
Voltage
Reference
EN/SET
S2Cwire
Interface
5
32x8 bit
ROM
OUT
8
Current
Mode
DAC
D1
D2
D3
D4
D5*
D6*
GND
* AAT3114 only
Functional Description
The AAT3113 and AAT3114 devices are high efficiency
1.5X fractional charge pumps intended for white LED
backlight applications. The fractional charge pump consists of a linear regulator followed by a 1.5X charge
pump. The AAT3113 and AAT3114 require only four
external components: two 1μF ceramic capacitors for the
charge pump flying capacitors (C1 and C2), one 1μF
ceramic capacitor for CIN, and one 0.33μF to 1μF ceramic capacitor for COUT. The charge pump output is converted into four or six constant current outputs (D1 to
D4 or D6) to drive four or six individual LEDs with a
maximum of 20mA each. The current source output
magnitude is controlled by the EN/SET serial data
S2Cwire interface. The interface records rising edges of
8
the EN/SET pin and decodes them into 32 individual current level settings each 1dB apart (see Table 1, Current
Level Settings). Code 32 is full scale, and Code 1 is full
scale attenuated by 31dB. The modulo 32 interface
wraps states back to state 1 after the 32nd clock. With
each EN/SET pulse, the output current increases by 1dB.
To decrease the output current by 1dB, 31 EN/SET clock
pulses are required. The counter can be clocked at
speeds up to 1MHz, so intermediate states are not visible. The first rising edge of EN/SET enables the IC and
initially sets the output LED current to -31dB, the lowest
setting equal to 525μA. Once the final clock cycle is input
for the desired brightness level, the EN/SET pin is held
high to maintain the device output current at the programmed level. The device is disabled 500μs after the
EN/SET pin transitions to a logic low state.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Applications Information
EN/SET Serial Interface
The current source output magnitude is controlled by the
EN/SET pin using Skyworks' Simple Serial Control
(S2Cwire) interface. The interface records rising edges of
the EN/SET pin and decodes them into 32 individual current level settings each 1dB apart. Code 32 is full scale,
and Code 1 is full scale attenuated by 31dB. The modulo
32 interface wraps states back to state 1 after the 32nd
clock, so 1dB of attenuation is achieved by clocking the
EN/SET pin 31 times (see graph titled, “IDIODE Response
-9dB to -10dB”). The counter can be clocked at speeds
up to 1MHz, so intermediate states are not visible. The
first rising edge of EN/SET enables the IC and initially
sets the output LED current to -31dB, the lowest setting
equal to 525μA. Once the final clock cycle is input for the
desired brightness level, the EN/SET pin is held high to
maintain the device output current at the programmed
level. The device is disabled 500μs after the EN/SET pin
transitions to a logic low state.
Current Level Settings
LED current level is set via the serial interface according
to a logarithmic scale where each code is 1dB greater
than the previous code. In this manner, the LED brightness appears linear with each increasing code.
Code
20mA max
Code
20mA max
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0.549
0.627
0.706
0.784
0.863
1.020
1.098
1.255
1.412
1.569
1.804
1.961
2.275
2.510
2.824
3.137
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
3.529
4.000
4.471
5.020
5.647
6.353
7.059
7.922
8.941
10.039
11.216
12.627
14.118
15.843
17.804
20.000
The EN/SET timing is designed to accommodate a wide
range of data rates. After the first rising edge of EN/SET,
the charge pump is enabled and reaches full capacity
after the soft-start time (TSS). During the soft-start time,
multiple clock pulses may be entered on the EN/SET pin
to set the final output current level with a single burst of
clocks. Alternatively, the EN/SET clock pulses may be
entered one at a time to gradually increase the LED
brightness over any desired time period. A constant current is sourced as long as EN/SET remains in a logic high
state. The current source outputs are switched off after
EN/SET has remained in a low state for at least the tOFF
timeout period (see Figure 2).
Table 1: Current Level Settings.
Normalized Current to Full Scale
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Code
Figure 1: Normalized Current Level Settings.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
9
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
tHI
tOFF
tLO
EN/SET
Code
2
1
OFF
3
OFF
Figure 2: EN/SET Timing Diagram.
THI > 50ns
2
ON/1
300ns < TLO < 75ms
3
4
5
6
50ns minimum to enable
n
(n < =32)
OFF
Figure 3: Enable/Disable/LED Brightness Level Set Data Input.
LED Selection
AAT3113 and AAT3114 devices are designed to drive
white LEDs with forward voltages to 4.2V. Since the
D1:D6 output current sources are matched with negligible voltage dependence, the LED brightness will be
matched regardless of their forward voltage matching.
Charge Pump Efficiency
The AAT3113 and AAT3114 devices are fractional charge
pumps. The efficiency () can be simply defined as a
linear voltage regulator with an effective output voltage
that is equal to one and one half times the input voltage.
Efficiency () for an ideal 1.5X charge pump can typically be expressed as the output power divided by the
input power:
η=
POUT
PIN
In addition, with an ideal 1.5X charge pump, the output
current may be expressed as 2/3 of the input current.
The expression to define the ideal efficiency () can be
rewritten as:
η=
POUT
VOUT · IOUT
V
=
= OUT
PIN
VIN · 1.5IOUT 1.5VIN
-or-
η(%) = 100
⎛ VOUT ⎞
⎝ 1.5VIN⎠
For a charge pump with an output of 5V and a nominal
input of 3.5V, the theoretical efficiency is 95%. Due to
10
internal switching losses and IC quiescent current consumption, the actual efficiency can be measured at 93%.
These figures are in close agreement for output load
conditions from 1mA to 100mA. Efficiency will decrease
as load current drops below 0.05mA or when the level of
VIN approaches VOUT. Refer to the Typical Characteristics
section of this datasheet for measured plots of efficiency
versus input voltage and output load current for the
given charge pump output voltage options.
Power Efficiency and Device Evaluation
The charge pump efficiency discussion in the previous section only accounts for efficiency of the charge pump section itself. Due to the unique circuit architecture and
design of the AAT3113 and AAT3114, it is very difficult to
measure efficiency in terms of a percent value comparing
input power over output power. Since the device outputs
are pure constant current sources, it is difficult to measure
the output voltage for a given output (D1 to D6) to derive
an output power measurement. For any given application,
white LED forward voltage levels can differ, yet the output
drive current will be maintained as a constant. This makes
quantifying output power a difficult task when taken in the
context of comparing to other white LED driver circuit
topologies. A better way to quantify total device efficiency
is to observe the total input power to the device for a
given LED current drive level. The best white LED driver
for a given application should be based on trade-offs of
size, external components count, reliability, operating
range, and total energy usage...not just “% efficiency.”
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
tions, size or area, material composition, and ambient
temperature. Capacitor ESR is typically measured in milliohms for ceramic capacitors and can range to more
than several ohms for tantalum or aluminum electrolytic
capacitors.
700
VIN = 3.6V
Input Power (mW)
600
500
400
300
Ceramic Capacitor Materials
200
Ceramic capacitors less than 0.1μF are typically made
from NPO or C0G materials. NPO and C0G materials
generally have tight tolerance and are very stable over
temperature. Larger capacitor values are usually composed of X7R, X5R, Z5U, or Y5V dielectric materials.
Large ceramic capacitors (i.e., greater than 2.2μF) are
often available in low-cost Y5V and Z5U dielectrics, but
capacitors greater than 1μF are not typically required for
AAT3113 or AAT3114 applications.
100
0
0
20
40
60
80
100
120
140
Output (LED) Current (mA)
Figure 3: AAT3113/AAT3114 Input Power
vs. LED Current
Capacitor Selection
Careful selection of the four external capacitors CIN, C1,
C2, and COUT is important because they will affect turn-on
time, output ripple, and transient performance. Optimum
performance will be obtained when low equivalent series
resistance (ESR) ceramic capacitors are used. In general, low ESR may be defined as less than 100m. A
value of 1μF for all four capacitors is a good starting
point when choosing capacitors. If the LED current
sources are only programmed for minimal current levels,
then the capacitor size may be decreased.
Capacitor Characteristics
Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the
AAT3113 and AAT3114 products. Ceramic capacitors
offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor typically has very low ESR, is lowest cost, has a smaller PCB
footprint, and is non-polarized. Low ESR ceramic capacitors help maximize charge pump transient response.
Since ceramic capacitors are non-polarized, they are not
prone to incorrect connection damage.
Equivalent Series Resistance
ESR is an important characteristic to consider when
selecting a capacitor. ESR is a resistance internal to a
capacitor that is caused by the leads, internal connec-
Capacitor area is another contributor to ESR. Capacitors
that are physically large will have a lower ESR when
compared to an equivalent material smaller capacitor.
These larger devices can improve circuit transient
response when compared to an equal value capacitor in
a smaller package size.
Test Current/Channel Disable
Each channel of the output is equipped with a test current function. The AAT3113 and AAT3114 use a small
(~150μA) current source injected into each output pin to
detect the presence of an LED. Unused channels other
than channel 1 should be left open and will be automatically diasbled instead of wasting the programmed output
current.
Thermal Protection
The AAT3113 and AAT3114 have a thermal protection
circuit that will shut down the charge pump and current
outputs if the die temperature rises above the thermal
limit. However, thermal resistance of the QFN package is
so low that if, in the case of the AAT3114, all six outputs
are shorted to ground at maximum 20mA output level,
the die temperature will not rise sufficiently to trip the
thermal protection. The thermal protection will only trip
if COUT is shorted to ground and the ambient temperature
is high.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
11
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Driving White LED Display Module
Backlights and Individual White LEDs
Connected in Parallel
The AAT3114 D1 to D6 outputs are true constant current
sources capable of driving up to 20mA each over the
operation input voltage range. Since these outputs are
true constant current sources, they may be connected in
parallel to drive a single power output. Any combination
of outputs (D1 to D6) may be connected in parallel. The
maximum total output current is a sum of parallel-con-
12
nected current sources. This feature is particularly useful
to power pre-manufactured display modules that are
pre-wired with white LED backlights connected in a parallel circuit configuration. All outputs can be connected in
parallel to drive groups of LEDs as well. The internal current source reference circuit bases feedback from current sensed on the D1 output. For best operation, the
only requirement for this application is that the output
D1 should always be connected to the load circuit.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Application Circuits
VIN
C1+
C1
1µF
C1C2+
OUT
V BATTERY
CIN
1µF
COUT
1µF
C2
1µF
AAT3114
C2-
EN/SET
D1
D2
D3
D4
D5
D6
EN/SET
Display µodule
D1
D2
D3
D4
D5
R4
R5
D6
GND
R1
R2
R3
R6
Resistor R is optional
Figure 4: AAT3114 Application Driving a Display Module With Six Parallel-Connected White LEDs.
VIN
C1+
C1
1µF
C1C2+
OUT
V BATTERY
CIN
1µF
COUT
1µF
C2
1µF
AAT3114
C2-
EN/SET
EN/SET
GND
Keyboard Backlight
D1
D2
D3
D4
D5
D6
Display Backlight
D4
D1
D2
D5
D6
D3
Enable Keyboard Backlight
Enable Display Backlight
Figure 5: AAT3114 Dual Backlight Control Circuit.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
13
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
Ordering Information
Package
Marking1
Part Number (Tape and Reel)2
TSOPJW-12
QFN44-16
HTXYY
FGXYY
AAT3113ITP-20-T1
AAT3114ISN-20-T1
Skyworks Green™ products are compliant with
all applicable legislation and are halogen-free.
For additional information, refer to Skyworks
Definition of Green™, document number
SQ04-0074.
Package Information
QFN44-163
2.400 ± 0.050
0.550 ± 0.020
0.330 ± 0.075
13
2.400 ± 0.050
1
4
9
8
4.000 ± 0.050
Pin 1 Identification
16
C0.3
0.650 BSC
5
2.280 REF
Top View
0.025 ± 0.025
Bottom View
0.214 ± 0.036
0.900 ± 0.100
4.000 ± 0.050
Pin 1 Dot By Marking
Side View
All dimensions in millimeters.
1. XYY = assembly and date code.
2. Sample stock is generally held on all part numbers listed in BOLD.
3. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing
process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection.
14
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
DATA SHEET
AAT3113/3114
High Efficiency 1.5X Fractional Charge Pumps for White LED Applications
TSOPJW-12
2.85 ± 0.20
2.40 ± 0.10
0.20 + 0.10
- 0.05
0.50 BSC 0.50 BSC 0.50 BSC 0.50 BSC 0.50 BSC
7° NOM
0.04 REF
0.055 ± 0.045
0.15 ± 0.05
+ 0.10
1.00 - 0.065
0.9625 ± 0.0375
3.00 ± 0.10
4° ± 4°
0.45 ± 0.15
0.010
2.75 ± 0.25
All dimensions in millimeters.
Copyright © 2012, 2013 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a
service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no
responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR
PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES
NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM
THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper
use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product
design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for
identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202128B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 16, 2013
15