Edco PC642 Series
Zone/Loop/Data
The Edco PC642 Series surge protective device, (SPD) is a two-pair (four wire) module
implementing three-stage hybrid technology. This SPD addresses over-voltage
transients with gas tubes and silicon avalanche components. In addition, sneak
and fault currents are mitigated with resettable fuses (PTCs). The PTCs increase
resistance several orders of magnitude when over-currents exceed safe levels. A
normal state resumes when over-currents are removed. The ability to self-restore in
this manner significantly increases suppressor performance and survivability.
The Edco PC642 card edge is gold-plated, double sided and is designed to mate with
the Edco PCB1B-WKEY gold-plated female terminal connector (sold separately).
When snapped together, the data circuits “pass thru” the protector in a serial
fashion from the four “Field Side” terminals to the four “Electronics Side” terminals.
Terminals 1 or 10 of the PCB1B must be attached to Building-Approved Ground.
EDCO PCB1B-WKEY BASE SOLD SEPARATELY
General Technical Specifications
Maximum Operating Voltage
5, 30, 36, 250 VDC
Clamping Voltage
8, 36, 43, 300 VDC
Operating Current
0.15 A
Peak Surge Current
10 kA (8 x 20 μs)
Frequency Range
0 to 20 MHz
Insertion Loss
< 0.1 dB at 50 MHz
SPD Technology
GDT, SAD, w/ Series PTC
Connection Type
Terminal Block, w/ compression lugs
Terminals accept up to 10 AWG
Operating Temperature
-40°C to +85°C
Dimensions (in / mm)
2.0˝ H x 1.0˝ W x 2.5˝ L (PC642 + Base)
[50.8 x 25.4 x 63.5 mm]
Weight (oz / kg)
1 oz [0.03 kg]
Certifications
UL 497A
Caution
Do not place this product in service on any signal line capable of supplying more than 150 mA continuously.
Attention
Ne pas placer ce produit dans le service sur une ligne de signal capable de fournir en permanence plus de
150 mA.
V DANGER!
Only qualified personnel should install or
service this system. Electrical safety precautions must be followed when installing
or servicing this equipment. To prevent risk
of electrical shock, turn off and lock out all
power sources to the unit before making
electrical connections or servicing.
Seulement le personnel qualifié doit installer
ou maintenir ce systéme. Des précautions
de sécurité en électricité doivent être suivis
lors de l’installation ou de la maintenance
de cet equipement. Pour eviter tout risque
de choc électrique, débranchez et verouiller
toutes les sources d’alimentation de cet
equipement avant de.
Features
■■ Three-stage hybrid protection
■■ Sneak/fault current protection
■■ Resettable fuses – PTCs
■■ Low capacitance option
■■ Plug-in module
■■ Requires Edco PCB1B-WKEY base
■■ Fast response time
■■ UL listed 497B
■■ 5 year warranty
Installation Instructions
Terminal Assignments
DRAWING 1
DRAWING 2
PCB1B-WKEY
Odd Terminals
Unprotected Pair 2
{
Field Side
Unprotected Pair 1
{
Even Terminals
10
9
8
7
6
5
4
3
2
1
}
Protected Pair 2
}
Protected Pair 1
Electronics Side
2.4"
[60.96]
2.125"
[53.98]
Keying Pin
1.0”
[25.40]
PCB1B-WKEY
Ground Terminal 1 or 10 to Building Approved Ground (preferably AC Power safety ground).
DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance
with all applicable codes.
Read and Understand These Instructions
Note:
• These protectors are intended for indoor use on communication loop
circuits which have been isolated from the Public Switch Telephone
Network.
• The communication loop circuits shall not be exposed to accidental
contact with the electric light or power conductors.
• The protectors shall be installed per the applicable requirements of
the National Electric Code, ANSI/NFPA 70.
• Measure DC operating voltage of system to insure it does not exceed
the rating of the selected surge device (5-250 VDC depending on the
device).
Installation:
1. Turn off power to circuit to be protected prior to installation.
2. Screw mounting base #PCB1B-WKEY (ordered separately) in desired
location preferably as close to protected equipment as possible and
in close proximity to a building approved grounding point using (2)
#4 screws. PCB1B may also be DIN rail mounted using optional DIN
clip assembly #11604KIT-PC (ordered separately).
3. Attach field side pairs (26-10 AWG) to positions 3/5 and 7/9, attach
electronics side pairs (26-10 AWG) to positions 2/4 and 6/8. Attach
ground wire (10 AWG) to positions 1 or 10 on base. See Drawing 1.
Torque wires to 44 lbf/in [8 kgf/cm].
4. Insert PC642C module into keyed PCB1B-WKEY base. See Drawing 2.
5. Apply power to protected circuit.
Emerson Network Power Contact information
Ordering Information
APPLICATIONS
PART NUMBER
RS485, RS422
PC642C-008LC & PCB1B-WKEY
RS232
PC642C-036LC & PCB1B-WKEY
E-NET, 10 BASE T
PC642C-036LC & PCB1B-WKEY
4–20 ma
PC642C-036LC & PCB1B-WKEY
OPTION
PART NUMBER
DIN Rail Kit Available
11604KIT-PC
How to Specify the Appropriate Model
*Other configurations available, please contact factory.
MODEL
MAX.
OPERATING
VOLTAGE
CLAMPING
VOLTAGE
(1000V@1 mA)
PC642C-008LC
5 VDC
8 VDC
PC642C-036LC
30 VDC
36 VDC
PC642C-043LC
36 VDC
43 VDC
PC642C-200LC
43-250 VDC
300 VDC
www.EmersonNetworkPower.com/Surge
Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
T: (607) 721-8840
T: (800) 288-6169
F: (607) 722-8713
E: [email protected]
IO-50105 5/14 Rev. 7 Printed in USA
Emerson Network Power, the Emerson Network Power logo and Edco are trademarks
and service marks of Emerson Electric Co. ©2014 Emerson Electric Co.
While every precaution has been taken to ensure accuracy and completeness herein, Emerson Network Power Surge Protection assumes no responsibility, and disclaims all liability, for damages
resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.