DLF0835 - AZ Displays, Inc.

LITEMAX DLF/DLH0835 V2
Sunlight Readable 8.4” LED B/L LCD
User Manual
(1st Edition 2012/3/23)
All information is subject to change without notice.
Approved by
Checked by
FOR MORE INFORMATION:
Prepared by
AZ DISPLAYS, INC.
75 COLUMBIA, ALISO VIEJO, CA 92656
PHONE:
(949) 360 5830
E-MAIL:
[email protected]
Website:
www.azdisplays.com
Page 1
RECORD OF REVISION
Version and Date
Mar,23,2012
Page
Old Description
all
New Description
Initial Release
Page 2
Remark
Contents
RECORD OF REVISION .................................................................................................. 2
Contents........................................................................................................................... 3
1.0 GENERAL DESCRIPTION ......................................................................................... 4
2.0 Input Terminals.......................................................................................................... 6
3.0 Electrical Characteristics ......................................................................................... 9
4.0 TIMING Characteristics of Input Signals ................................................................11
5.0 Input Signals, Basic Display Colors and Gray Scale of Each Color ................... 12
6.0 OPTICAL SPECIFICATION...................................................................................... 13
7.0 LED DRIVING BOARD SPECIFICATIONS .............................................................. 16
8.0 AD5621GD SPECIFICATION (DLH0835 V2 Only) .................................................. 19
General Description ...................................................................................................... 19
Supported Timing (*by your panel resolution) ........................................................... 20
Outline Dimensions ...................................................................................................... 22
Pin Define ................................................................................................................ 23
CN1: Panel connector ...................................................................................... 24
CN2: DVI-D Input connector ............................................................................. 24
CN3: DVI-D Input connector(16pin connector) ................................................. 25
CN4: Analog RGB Input connector(D-SUB 15Pin) ........................................... 25
CN5: Analog RGB Input connector(13pin connector) ....................................... 25
J1: Power DIN Jack(12V).................................................................................. 26
J2: Power connector(12V) ................................................................................ 26
J3: Power connector(5V) .................................................................................. 26
J4: Inverter Connector ...................................................................................... 26
J5,J6: FAN ........................................................................................................ 26
J7: Key Pad ...................................................................................................... 26
J8: TO Audio PCB connector(Audio control) .................................................... 27
J9: Ambient ....................................................................................................... 27
J10: VR connector ............................................................................................ 27
J11: G-PROBE(RS232)..................................................................................... 27
JP1:PANEL VCC............................................................................................... 27
DC characteristics............................................................................................. 27
OSD menu...................................................................................................................... 28
9.0 MECHANICAL DRAWING........................................................................................ 34
10.0 PRECAUTIONS ...................................................................................................... 35
Page 3
1.0 GENERAL DESCRIPTION
DLF/DLH0835 V2 is a replaced model of DLF/DLH0835 V1. It is a color TFT-LCD Display
as active switching devices with 1,000nits LED backlight powered by Durapixel™
technology. This LCD display has a 8.4 inch diagonally measured active area with SVGA
resolutions (800 horizontal by 600 vertical pixel array). Each pixel is divided into RED,
GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.2M
colors.
1.1 FEATURES









Sunlight Readable
LED Backlight
High Shock & Vibration Resistance
Low Power Consumption
High Uniformity
Low EMI Noise
Wide Dimming
Life Expectancy
Operation Temperature
1.2 GENERAL SPECIFICATIONS
Model No. DLF0835 V2 Description Display Area (mm) Brightness Resolution Contrast Ratio Pixel Pitch (mm) Viewing Angle Display Colors Response Time (Typical) Sync Power Consumption Dimensions (mm) Weight (Net) 8.4” TFT LCD, LED Backlight 1000 nits, SVGA 170.4(H) x 127.8(V) 1000 cd/m2 SVGA (800 x 600) 450 : 1 0.213 x 0.213 130°(H), 120°(V) 16.2M / 262K 35 ms LVDS W 199.5(W) x 154(H) x 12.45(D) 0.33Kg DLH0835 V2 1.3 Difference of V1 & V2
Model
Bezel
Opening
Outline
Dimension
View Angle
Response
Color
Time
Contrast
Ratio
LID
Dimension
DLF0835 V1
175.5x133
199.5x149.5x11.6
120°(H)~120°(V)
30ms
16.2M
600:1
124x50x15
DLF0835 V2
173.4x130.8
199.5x154x11.6
130°(H)~120°(V)
35ms
262K/16.2M
450:1
70x30x7
Page 4
1.4 ABSOLUTE MAXIMUM RATINGS
Page 5
2.0 Input Terminals
Page 6
Page 7
Page 8
3.0 Electrical Characteristics
Page 9
Page 10
4.0 TIMING Characteristics of Input Signals
Page 11
5.0 Input Signals, Basic Display Colors and Gray Scale of Each Color
Page 12
6.0 OPTICAL SPECIFICATION
Optical
Item
Red
Color
chromaticity
Data
Unit
Rx
0.5655
-
Ry
0.3286
-
Gx
0.3496
-
Gy
0.6036
-
Symbol
Green
Condition
Bx
θx=0
0.1492
-
By
θy=0
0.1196
-
Wx
BM-7
0.3041
-
Wy
0.3453
-
Center Luminance of White
Lc
1000
cd/㎡
Average
La
997
cd/㎡
Uniform
Lu
80
%
Contrast Ratio
CR
450 : 1
-
54.33
%
Blue
White
Color Saturation
Viewing
Angle
NTSC
Horizontal
Vertical
θx=0
θy=0
Klein K-10
θx+
θxθy+
Note
Test Mode:
(1)
(2)
(3)
Test Mode:
(1)
(4)
65
CR≧10
θy-
65
60
55
Page 13
Deg
Test Mode:
(1)
(3)
Test Mode: (1) Definition of Viewing Angle(θx,θy):
(2) Definition of Test Point:
A
B
C
1
2
3
Active Area
Page 14
(3)BM-7 Measurement Setup:
(4)Klein K-10 Measurement Setup:
Page 15
7.0 LED DRIVING BOARD SPECIFICATIONS
1. LED Application This specification is applied to LED converter unit for DLF/DLH0835 V2(1000nit) LED backlight 2. Operating Characteristics Item Symbol MIN. TYP. MAX. Unit Remark
Conditions
Input Voltage Vin Input Current (Low Brightness) VIN=12V,Vadj=5V IinL Input Current (High Brightness) 10.0 12.0 14.0 3 ‐‐‐‐‐ ‐‐‐‐‐ 0.456 0.377
0.319 0.0 ‐‐‐‐‐ ‐‐‐‐‐ 0.172 0.172
0.172 VIN=12V,Vadj=5V IoutL LED Current VIN=12V,Vadj=0V 200 220 HZ 0.5 ‐‐‐‐‐ 4.8 2 ‐‐‐‐‐ 5 24.172
24.136
24.121 V 91.75 91.76 92.90 523 550 PWM Frequency Brightness Control Freq VIN=12V
180 Efficiency Vout η Normal Operation VIN=12V,Vadj=0V VIN=12V,Vadj=0V Page 16
Arms KHz VIN=12V,Vadj=0V
Von/off 580 Freq Connection of Voltage
A Working Frequency Output Voltage A IoutH Vadj mA (High Brightness) ON/OFF Control V VIN=12V,Vadj=0V IinH LED Current (Low Brightness) V V % Vadj±5%
3. Connector Socket 3‐1. Input Connector: J3(JST S 8B‐PH‐SM3‐TB or Compatible PIN No Symbol Description 1 Vin DC+12V 2 Vin DC+12V 3 Vin DC+12V 4 GND Ground 5 GND Ground 6 GND Ground 7 Brightness Brightness Control 5V~0V 8 Control ON/OFF Control 0.8V(OFF) 2~5V(ON) 3‐2 .Output Connector: J1,J2(JST S 2B‐ZR‐SM3A‐TF or Compatible) PIN NO Symbol Description 1 Output LED High Voltage( + ) 2 Output LED Low Voltage ( ‐ ) Page 17
4. Mechanical Characteristics Dimension: 70mm*30mm*7mm
INPUT CONNECTOR
J3:
PIN1:VIN
PIN2:VIN
PIN3:VIN
PIN4:GND
PIN5:GND
PIN6GND
PIN7:BRIGHTNESS
PIN8:ON/OFF
7mm
Page 18
8.0 AD5621GD SPECIFICATION (DLH0835 V2 Only)
We developed this A/D board to support industrial high brightness and commercial
applications. This A/D board has many functions. It has options of external luminance
sensor, a surface mounted VR button to control the brightness, fan rotation and thermal
sensor. The rev.1 has released for European RoHS Compliant purpose.
General Description











Max Resolution Up To WXGA 60Hz
LVDS Output
Support Panel DC5V or 3.3V, 12V Output
External Fan Control by Software
OSD Control
Inverter 0~5V Dimming Control
2Wx2 Audio Output
Input Power 12V
Analog signal Input (RGB)
*External V.R. brightness control
*External light sensor brightness control
Page 19
Supported Timing (*by your panel resolution)
The following table displays optimum quality modes that the LCD monitor provides. If the other video
modes are used, the monitor will stop working or display a poor quality picture.
TIMMING
MODE
RESOLUTION
VGA
[email protected]
[email protected]
[email protected]
SVGA
[email protected]
[email protected]
[email protected]
[email protected]
XGA
[email protected]
[email protected]
[email protected]
SXGA
[email protected]
[email protected]
[email protected]
WXGA
[email protected]
Page 20
Page 21
Outline Dimensions
unit:mm
Page 22
Pin Define
Page 23
CN1: Panel connector
Pin No.
Function
Pin No.
Function
1
RxO0+
16
RxE1-
2
RxO0-
17
RxE2+
3
RxO1+
18
RxE2-
4
RxO1-
19
RxEC+
5
RxO2+
20
RxEC-
6
RxO2-
21
RxE3+
7
RxOC+
22
RxE3-
8
RxOC-
23
GND
9
RxO3+
24
GND
10
RxO3-
25
GND
11
GND
26
GND
12
GND
27
PANEL-VCC
13
RxE0+
28
PANEL-VCC
14
RxE0-
29
PANEL-VCC
15
RxE1+
30
PANEL-VCC
CN2: DVI-D Input connector
Pin No.
Function
Pin No.
Function
Pin No.
Function
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2/4
Shield
11
T.M.D.S Data1/3
Shield
19
T.M.D.S. Data0/5
Shield
4
T.M.D.S. Data4-
12
T.M.D.S. Data3-
20
T.M.D.S. Data5-
5
T.M.D.S. Data4+
13
T.M.D.S. Data3+
21
T.M.D.S. Data5+
6
DDC Clock
14
+5V Power
22
7
DDC Data
15
8
Not Connected
16
Ground
(for +5V)
Hot Plug Detect
Page 24
T.M.D.S. Clock
Shield
23
T.M.D.S. Clock+
24
T.M.D.S. Clock-
CN3: DVI-D Input connector(16pin connector)
Pin No.
Function
Pin No.
Function
Pin No.
Function
1
T.M.D.S.
7
DDC Data
13
GND
2
T.M.D.S.
8
DDC Clock
14
GND
3
T.M.D.S.
9
GND
15
Hot Plug Detect
4
T.M.D.S.
10
GND
16
+5V Power
5
T.M.D.S.
11
T.M.D.S. Clock-
6
T.M.D.S.
12
T.M.D.S. Clock+
CN4: Analog RGB Input connector(D-SUB 15Pin)
Pin No.
Symbol
Description
Pin No.
Symbol
Description
1
RED
Analog Red
9
NC
+5VDC
2
GREEN
Analog Green
10
SGND
Sync GND
3
BLUE
Analog Blue
11
NCD
Reserved
4
GND
Reserved
12
SDA
DDC Serial Data
5
NC
VGA_CAB
13
HSYNC
Horizontal Sync
6
RGND
Red Return
14
VSYNC
Vertical Sync
7
GGND
Green Return
15
SCL
DDC Data Clock
8
BGND
Blue Return
CN5: Analog RGB Input connector(13pin connector)
Pin No.
Symbol
Description
Pin No.
Symbol
Description
1
SCL
DDC Data Clock
8
RED
Analog Red
2
SDA
DDC Serial Data
9
GGND
Green Return
3
GND
Reserved
10
GREEN
Analog Green
4
NC
VGA_CAB
11
BGND
Blue Return
5
VSYNC
Vertical Sync
12
BLUE
Analog Blue
6
HSYNC
Horizontal Sync
13
NC
+5VDC
7
RGND
Red Return
Page 25
J1: Power DIN Jack(12V)
Pin No.
Function
Pin No.
Function
1
12VDC
2
12VDC
3
GND
4
GND
J2: Power connector(12V)
Pin No.
Function
Pin No.
Function
1
12VDC
4
GND
2
12VDC
5
GND
3
12VDC
6
GND
J3: Power connector(5V)
Pin No.
Function
Pin No.
Function
1
5VDC
2
5VDC
3
GND
4
GND
J4: Inverter Connector
Pin No.
Symbol
Description
Pin No.
Symbol
Description
1
ON/OFF
Backlight ON/OFF
5
GND
GND
2
BRIGHT
Dimming adjust
6
12VDC
Input 12VDC
3
GND
GND
7
12VDC
Input 12VDC
4
GND
GND
8
12VDC
Input 12VDC
J5,J6: FAN
Pin No.
Function
Pin No.
Function
1
FAN(+)
2
GND
J7: Key Pad
Pin No.
Function
Pin No.
Function
1
POWER KEY
6
MENU KEY
2
GREEN LED
7
AUTO KEY
3
RED LED
8
GND
4
LEFT KEY
9
GND
5
RIGHT KEY
Page 26
J8: TO Audio PCB connector(Audio control)
Pin No.
Function
Pin No.
Function
1
12VDC
5
5VDC
2
12VDC
6
Volume
3
GND
7
Mute
4
GND
J9: Ambient
Pin No.
Function
Pin No.
Function
1
NC
3
GND
2
L_Sensor
J10: VR connector
Pin No.
Function
Pin No.
Function
1
3,3VDC
2
VR
3
GND
J11: G-PROBE(RS232)
Pin No.
Function
Pin No.
Function
1
5VDC
3
RXD
2
TXR
4
GND
Pin No.
Function
Pin No.
Function
1-2
12V
5-6
3.3V
3-4
5V
JP1:PANEL VCC
DC characteristics.
Power Consumption
6
W
Operation Temperation
0~70
℃
Storage Temperature
-20~85
℃
Note: This Value is for a/d board body.
Page 27
Note1
OSD menu
Here are some instructions for you to use the OSD (On Screen Display). By pressing the “menu”, you
will see the below picture.
Timing shows resolution, H-frequency,and V-frequency of the panel.Version shows the firmware
control version. This 2 information is not changeable by user.
There are 7 sub pages inside the OSD manual, Brightness, Signal select, Sound, Color, Image, Tools,
and Exit.
When you press “menu” button, you enter the “Brightness” sub page.
press ’’menu’’
press ’’menu
press ’’menu’’
You will see 4 selections:
press ’’menu’’
OSD Brightness:
press ’’right’’ key
press “menu” once, you can go into adjust the brightness. Press “left”
you can dim down the brightness to “0”, while press “right” you can
increase the brightness to “100”.
Ambient light sensor: press this Icon, must to accompany with Litemax
ambient light sensor to auto dimming.(OPTION)
Potentiometer: press this icon, adjust VR function.(OPTION)
Ambient light sensor with OSD offset: press this Icon
Press ’’right’’ key
Press ’menu’’ once, you can adjust min. luminance to fit your
application (OPTION)
Contrast: Press “menu” and “right” you can adjust the contrast from “0” to
“100” by pressing the “left” and “right”.
Exit: You can exit this sub menu back to normal screen.
Page 28
Analog: RGB/VGA INPUT
Digital: DVI input
Exit: You can exit this sub menu back to normal screen.
There are 3 options for “Sound” sub page.
Audio Volume: Audio volume adjustment.
Mute: You can mute the speaker by pressing this option.
Exit: back to the normal screen.
Page 29
Auto Color: by press this “Auto Color” option, you can get the optimal color
performance.
SRGB: Windows standard color setting.
Color Tempture: You can have 3 options in this selection.
Color Tempture User
Color Tempture_6500K
Color Tempture_93OOK
“user mode”, “6500K” (Warm color scheme), “9300K (Cold color scheme).
Def ault is “user”, and inside all “R”, “G”, and “B” are set “100”
Exit: back to the normal screen.
Page 30
Go into the “Image” page, you can see below picture.
Auto just: Pressing this option, the AD5621 will adjust the optimal frequency of
horizontal and vertical.
You will see “Auto tune….” On the screen for around
3 seconds.
Clock: If you are not satisfied about the Autotune result, you can adjust
manually by “Clock”.
The screen will be “wider” if you adjust this function.
Phase: If you see “double image” on characters, you can adjust “Phase” to
make it perfect image.
HPos: You can shift the screen horizontally by this function.
Vpos: You can shift the screen vertically by this function.
Exit: Back to normal screen.
On the “Tools” sub menu, you will see 5 icons.
Osd Control: Select this option, you will see 4 more options:
Page 31
Osd_time: You can selection the time of OSD from 2 sec. to 16 sec.
D
Osd_HPos: You can move the OSD horizontally over the screen.
Osd_VPos: You can move the OSD Vertically over the screen.
Exit: back to main menu.
Factory_Reset: By pressing this, the screen will be back to the factory setting
on very beginning and lost all the personal settings.
Sharpness: You can make the characters looks sharper.
Dos_mode/Gxf_mode: Some old programs running over 640x400 and
720x400 (DOS Mode and graphics mode), you need to select this option
manually.
Exit
Factory Burn-in mode: While your VGA cable is connected on the monitor, press “Menu” and Left
<” simultaneously, you will see “BURN IN MODE” on the center of the screen for 3 sec. Then unplug
the VGA cable, the screen will show Red, Green, Blue, White, and Black in sequence automatically.
You can plug in the VGA signal cable, and re-plug the power connector to exit the burn-in mode.
Page 32
OSD Lock Function: It is possible to lock all the OSD buttons to prevent unauthorized changes to
occur by pressing “Menu” and “right >” buttons simultaneously.
the center of the screen for 3 seconds.
You will see the “lock” icon below on
If any button is pushed after the lock function is initiated,
the below icon will appear on the screen.'
To release the OSD lock, press “Menu” and “Right >”.
the screen for 3 seconds.
The below icon will appear on the center of
Now all OSD keys are active again.
Page 33
9.0 MECHANICAL DRAWING
Page 34
10.0 PRECAUTIONS
HANDLING PRECAUTIONS
(1) The module should be assembled into the system firmly by using every mounting hole. Be careful
not to twist or bend the module.
(2) While assembling or installing modules, it can only be in the clean area. The dust and oil may cause
electrical short or damage the polarizer.
(3) Use fingerstalls or soft gloves in order to keep display clean during the incoming inspection and
assembly process.
(4) Do not press or scratch the surface harder than a HB pencil lead on the panel
because the polarizer is very soft and easily scratched.
(5) If the surface of the polarizer is dirty, please clean it by some absorbent cotton or soft cloth. Do not
use Ketone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It
might permanently damage the polarizer due to chemical reaction.
(6) Wipe off water droplets or oil immediately. Staining and discoloration may occur if
they left on panel for a long time.
(7) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contacting with hands, legs or clothes, it must be washed away thoroughly with soap.
(8) Protect the module from static electricity, it may cause damage to the C-MOS Gate Array IC.
(9) Do not disassemble the module.
(10) Do not pull or fold the lamp wire.
(11) Pins of I/F connector should not be touched directly with bare hands.
STORAGE PRECAUTIONS
(1) High temperature or humidity may reduce the performance of module. Please store
LCD module within the specified storage conditions.
(2) It is dangerous that moisture come into or contacted the LCD module, because the
moisture may damage LCD module when it is operating.
(3) It may reduce the display quality if the ambient temperature is lower than 10 ºC. For
example, the response time will become slowly, and the starting voltage of lamp will be higher than
the room temperature.
OPERATION PRECAUTIONS
(1) Do not pull the I/F connector in or out while the module is operating.
(2) Always follow the correct power on/off sequence when LCD module is connecting and
operating. This can prevent the CMOS LSI chips from damage during latch-up.
Page 35