PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF HYDIS AND MUST BE RETURNED TO HYDIS UPON ITS REQUEST TITLE : HV056WX1-101 Product Specification Rev. P0 FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 Http://www.AZDISPLAYS.com HYDIS Technologies SPEC. NUMBER B2005-C001-C (1/3) PRODUCT GROUP TFT LCD REV. P0 ISSUE DATE 2011.01.12 PAGE 1 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 REVISION HISTORY REV. ECN NO. P0 SPEC. NUMBER DESCRIPTION OF CHANGES Initial Release SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (2/3) DATE PREPARE D 11.01.12 B.M SEO PAGE 2 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 Contents No 1 ITEM Page REVISIONS HISTORY 2 CONTENTS 3 GENERAL DESCRIPTION 4 1.1 Introduction 1.2 Features 1.3 Applications 1.4 General Specification 2 ABSOLUTE MAXIMUM RATINGS 6 3 OPTICAL SPECIFICATIONS 7 4 ELECTRICAL SPECIFICATIONS 9 4.1 TFT LCD Module 4.2 Back-Light Unit 4.3 PWM Duty Ratio vs Brightness 5 INTERFACE CONNECTION 12 5.1 Electrical Interface Connection 5.2 LVDS Interface 5.3 Data Format 6 SIGNAL TIMING SPECIFICATIONS 15 6.1 Timing Parameter of TFT LCD Module Input Signal 6.2 Timing Waveform of TFT LCD Module Input Signal 6.3 LVDS Rx Interface Timing Parameters 6.4 Input Signals, Basic Display Colors & Cray Scale Of Colors 6.5 Power Sequence 7 MECHANICAL CHARACTERISTICS 19 8 RELIABLITY 21 9 PRODUCT SERIAL NUMBER 22 10 PACKING 23 11 HANDING & CAUTIONS 25 12 APPENDIX 26 SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 3 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 1.0 GENERAL DESCRIPTION 1.1 Introduction HV056WX1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 5.6 inch diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 262,144 colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type. SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 4 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 1.2 Features z High Resolution & Wide View (HFFS Technology) z 3.3 V Logic Power & 12V LED Power Supply z 1 Channel LVDS Interface z 262,144 Colors z Low Weight (Slimming Glass & Slim LGP LED Backlight Technology) z Compact Design (Source & Gate IC of the COG Type) z Green Product (RoHS Compliant) 1.3 Applications z Display terminals for Ultra Mobility Personal Computer. 1.4 General Specification The followings are general specification at the model HV056WX1-100. < Table 1. General Specification > Parameter Specification Unit Active area 120.96(H) × 75.60(V) Number of pixels 1280(H) × 800(V) pixels Pixel pitch 94.5(H) × 94.5(V) um Pixel arrangement RGB Vertical stripe Display colors 262,144 Display mode Normally Black Dimensional outline 131.7±0.4(H)×87.7±0.4(V)×4.7±0.3(T) mm Weight 61 (typ.) / 65 (max.) gram Back-light Bottom edge side, 16-LEDs type SPEC. NUMBER mm colors SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) Remarks White LED PAGE 5 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. [VSS=GND=0V] < Table 2. Absolute Maximum Ratings > Parameter Symbol Min. Max. Unit VDD VSS-0.3 5.0 V HVDD -0.3 40.0 V VR - 5 V + 25 ℃ ILED - 30 mA + 50 ℃ ILED - 20 mA Operating Temperature TOPR 0 60 ℃ Storage Temperature TSTG -20 70 ℃ Logic Power Supply Back-light Power Supply Back-Light LED Reverse Voltage Back-light LED Current Remarks Ta = 25 ℃ Note 1 Note 1, 2 Note : 1. Ambient temperature vs allowable forward current are shown in the figure below. 2. Temperature and relative humidity range are shown in the figure below. 90% RH Max. ( 40℃ ≥ Ta) Maximum wet - bulb temperature at 39℃ or less. ( > 40℃) No condensation. Relative Humudity 100 (40, 90) 90 80 60 Operating Range (50, 50) 40 (60, 27) 20 Storage Range 5 -40 -20 0 20 40 60 80 Temperature (℃) SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 6 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 3.0 OPTICAL SPECIFICATION The test of Optical specification shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometric system and TOPCON BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. < Table 3. Optical Specifications > Parameter Min Typ Max Unit 80 85 - Deg. 80 85 - Deg. 80 85 - Deg. Θ6 80 85 - Deg. Contrast ratio CR 350 500 - Luminance of White Yw 250 300 - cd/m2 White Luminance uniformity ΔY9 75 - - % Wx 0.293 0.323 0.353 Wy 0.329 0.359 0.389 0.545 0.575 0.605 0.311 0.341 0.371 0.330 0.360 0.390 0.554 0.584 0.614 Bx 0.124 0.154 0.184 By 0.120 0.150 0.180 Viewing Angle Symbol Condition Horizontal Vertical White Θ3 Θ9 Θ12 Rx Red Ry Reproduction of color Gx Green Gy Blue Response Time (Tr + Td) Cross Talk SPEC. NUMBER CR > 10 Θ = 0° Θ = 0° (Center) Normal Viewing Angle Note 1 Θ = 0° 30 - - 2.0 SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) Note 2 Note 4,5 Note 3 Ta= 25° C CT Remark ms Note 6 % Note 7 PAGE 7 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 Note : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. (see Figure1 in Appendix). 2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See Figure 1 in Appendix) Luminance Contrast Ratio (CR) is defined mathematically as CR = Luminance when displaying a white raster / Luminance when displaying a black raster. 3. Reference only / Standard Front Surface Treatment Measured with green cover glass. The color chromaticity coordinates specified in Table 3 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 4. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 9 points / Maximum Luminance of 9 points ) * 100 (See Figure 2 shown in Appendix). 5. The electro-optical response time measurements shall be made as Figure 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. 6. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark (Refer to Figure 5 in Appendix) Cross-Talk (%) = YB - YA × 100 YB SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 8 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 4.0 ELECTRICAL SPECIFICATION 4.1 TFT LCD Module < Table 4. LCD Module Electrical Specification > [Ta =25±2 ℃] Values Parameter Symbol Min Typ Max Unit Remark Logic Power Supply Voltage VDD 3.0 3.3 3.6 V Note 1 Logic Power Supply Current IDD 220 270 290 mA Note 1 Vertical Sub Line PMAX 970 1050 1130 mW Mosaic (32 X 32) PEBL 790 860 930 mW Vsync Frequency fV 40 60 70 Hz Hsync Frequency fH 32.9 49.2 57.6 KHz Main Clock Frequency fclk 47.4 71.1 83 MHz High Level Differential Input Signal VIH - - + 100 mV Low Level Differential Input Signal VIL - 100 - - mV Power Consumption Note 1,2 Note 3 VCM =1.2V Note : 1. The supply voltage is measured and specified at the interface connector of LCM. Test pattern is mosaic pattern (32 X 32) 2. The current draw and power consumption specified is for 3.3V and 60Hz at 25℃. 3. In Min. of Vsync Frequency, this value only guarantee to drive condition. The driving frequency is measured at the following Horizontal and Vertical Parameters. Horizontal Active 1280 Pixels Vertical Active 800 Lines Horizontal Front porch 48 Pixels Vertical Front porch 3 Lines Horizontal Sync Blanking 32 Pixels Vertical Sync Blanking 6 Lines Horizontal back porch 80 Pixels Vertical Back Porch 14 Lines Vertical period 823 Lines Horizontal Period SPEC. NUMBER 1440 Pixels SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 9 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 4.2 Back-Light Unit [Ta =25±2 ℃] < Table 5. Back-Light Unit Electrical Specification > Values Parameter Symbol Unit Remark Min Typ Max HVDD 4.5 12.0 16.0 V Power Consumption PBL - 840 1100 mW LED Driver’s Efficiency η - 85 - % FPWM 100 200 1000 ㎐ High Level PWM Signal Voltage VPWMH 1.4 - 5.0 V Low Level PWM Signal Voltage VPWML 0 - 0.2 V Back-light LED Voltage / Back-light LED Total Voltage VLED /VBL - 3.3 / 26.4 V Note 3 Back-light LED Current / Back-light LED Total Current ILED /IBL - 15 / 30 mA Note 3 12,000 - Hrs By LED @15mA Back-Light Power Supply Back-light PWM Frequency Life Time - Note 1, 2 Note 2 Note : 1. The power supply voltage and current is measured and specified at the interface connector of LCM including LED Driver. 2. Reference value, which is measured with LED Driver for 12V. 3. Calculated value for reference (VLED × ILED × # of LEDs (16EA) ). SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 10 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 Relative Brightness (%) 4.3 PWM Duty Ratio vs Brightness Duty Ratio (%) Note : In case of duty ratio 0%, LED can’t illuminate itself so this state is LED off. In case of duty ratio 100%, the brightness of LED is maximum and the state is LED on. SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 11 OF 29 A4(210 X 297) 5.0 PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 INTERFACE CONNECTION. 5.1 Electrical Interface Connection < Table 6. Electrical Interface Connection Specification > (RECE., CN1 :20347-025E-02, I-PEX) Pin No Symbol Description Pin No Symbol Description 1 LEDVDD Back-light Power Supply 14 IN1+ LVDS Receiver Signal (+) 2 LEDVDD Back-light Power Supply 15 IN2- LVDS Receiver Signal (-) 3 NC No Connection 16 IN2+ LVDS Receiver Signal (+) 4 LED GND Back-light Ground 17 CLK- LVDS Receiver Clock Signal(-) 5 LED GND Back-light Ground 18 CLK+ LVDS Receiver Clock Signal(+) 19 GND Ground 20 TEST TEST PIN GROUND 6 7 PWM PWM Brightness Control ON/OFF LED Drive ON/OFF 8 GND GROUND 21 GND 9 GND GROUND 22 NC 10 GND GROUND 23 VDD Logic Power Supply 11 IN0- LVDS Receiver Signal (-) 24 VDD Logic Power Supply 12 IN0+ LVDS Receiver Signal (+) 25 VDD Logic Power Supply 13 IN1- LVDS Receiver Signal (-) NON-CONNECTION Note : 1. NC : This pins are only used for HYDIS internal operations 2. Start from left side 3. User Side Connector (Plug) : 20345-025T-02, I-PEX Rear view of LCM 1 SPEC. NUMBER 20347-025E-02 250 SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 12 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 5.2 LVDS Interface < Table 7. LVDS Interface Specification > [LVDS Transmitter : THC63LVDM83A] Transmitter Input signal Pin No R0 51 R1 52 R2 54 R3 55 R4 56 R5 3 G0 4 G1 6 G2 7 G3 11 G4 12 G5 14 B0 15 B1 19 B2 20 B3 22 B4 23 B5 24 HSYNC 27 VSYNC 28 DE 30 MCLK 31 SPEC. NUMBER Interface 20347-024E-02 Pin No System (Tx) TFT-LCD (Rx) Pin No. 48 47 OUT0OUT0+ IN0IN0+ 11 12 46 45 OUT1OUT1+ IN1IN1+ 13 14 42 41 OUT2OUT2+ IN2IN2+ 15 16 40 CLKOUT- CLKIN- 17 39 CLKOUT+ CLKIN+ 18 SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) Remark PAGE 13 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 5.3 Data Input Format ODD (1,1) EVEN (2,1) (1279,1) (1280,1) R G B R G B R G B R G B 1 Pixel = 3 Dots R G B R G B R G B (1,800) (2, 800) SPEC. NUMBER R G B R G B Display Position of Input Data (V-H) (1279,800)(1280,800) SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 14 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 6.0 SIGNAL TIMING SPECIFICATION 6.1 Timing Parameters of TFT LCD Module Input Signal < Table 8. Input Timing Parameters Specification > [ DE only, VDD=3.3V, GND=0V, TA=25℃] Parameter Symbol Min Typ Max Unit Frame Period T1 810 823 836 Lines Vertical Display Period T2 - 800 - Lines One line Scanning Period T3 1370 1440 1600 Clocks Horizontal Display Period T4 - 1280 - Clocks 1/T5 47.4 71.1 83 MHz Clock Frequency Note 6.2 Timing Waveforms of TFT LCD Module Input Signal T1 T2 DE T3 DCLK T5 T4 DE DATA SIGNALS SPEC. NUMBER Valid display data (1280 Clocks) SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 15 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 6.3 LVDS Rx Interface Timing Parameter The specification of the LVDS Rx interface timing parameter < Table 9. LVDS Rx Interface Timing Specification> Item Symbol Min. Typ. Max. Unit CLKIN Period tRICP 12.50 14.43 25.00 nsec Input Data 0 tRIP0 -0.4 0.0 +0.4 nsec Input Data 1 tRIP1 tRICP/7-0.4 tRICP/7 tRICP/7+0.4 nsec Input Data 2 tRIP2 2 ×tRICP/7-0.4 2 ×tRICP/7 2 ×tRICP/7+0.4 nsec Input Data 3 tRIP3 3 ×tRICP/7-0.4 3 ×tRICP/7 3 ×tRICP/7+0.4 nsec Input Data 4 tRIP4 4 ×tRICP/7-0.4 4 ×tRICP/7 4 ×tRICP/7+0.4 nsec Input Data 5 tRIP5 5 ×tRICP/7-0.4 5 ×tRICP/7 5 ×tRICP/7+0.4 nsec Input Data 6 tRIP6 6 ×tRICP/7-0.4 6 ×tRICP/7 6 ×tRICP/7+0.4 nsec Remarks tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 tRIP1 tRIP0 RxINz +/* Z = 0, 1, 2 Rx RxCLKIN+/- Rx Rx Rx Rx Vdiff=0[v] Rx Rx Rx Rx Rx Rx Vdiff=0[v] tRICP SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 16 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 6.4 Input Signals, Basic Display Colors & Gray Scale Of Colors Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of 262,144 colors are derived from the resultant 18 bit data. Colors & Gray Scale Black Blue Green Basic Cyan Colors Red Magenta Yellow White Black △ Darker Gray △ Scale Of ▽ Red Brighter ▽ Red Black △ Darker Gray △ Scale Of ▽ Green Brighter ▽ Green Black △ Darker Gray △ Scale Of ▽ Blue Brighter ▽ Blue Black △ Gray Darker Scale △ Of White ▽ & Brighter Black ▽ White SPEC. NUMBER Red Data Green Data R5 R4 R3 R2 R1 R0 G5 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 1 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 ↓ ↓ 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 0 1 1 0 0 1 1 0 1 0 1 0 1 1 1 0 1 1 1 0 1 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 ↓ ↓ 1 1 1 0 1 0 1 0 1 0 1 0 0 0 ↓ ↓ ↓ ↓ 1 1 1 0 1 1 1 0 1 1 1 1 1 1 1 SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) 0 1 0 1 0 1 0 1 0 0 0 ↓ ↓ 0 0 0 0 0 0 1 1 1 0 0 0 ↓ ↓ 1 1 1 0 0 1 1 0 0 1 1 0 0 0 ↓ ↓ ↓ ↓ 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 0 0 ↓ ↓ ↓ ↓ 0 0 0 0 0 0 Blue Data G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 1 1 1 PAGE 17 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 6.5 Power Sequence To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below 0.9VDD 0.1VDD Power Supply 0.9VDD 0.1VDD 0V T1 T5 T6 T2 Interface Signal ( Input Data ) Valid 0V T3 BLU On/Off T4 0V Values Parameter Units Min Typ Max T1 0.5 - 10 ms T2 0.5 - 50 ms T3 10 - - ms T4 10 - - ms T5 0.5 - 50 ms T6 200 - - ms Note : 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid. SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 18 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 7.0 MECHANICAL CHARACTERISTICS 7.1 Dimensional Requirements Figure 5 (located in Appendix) shows mechanical outlines for the model HV056WX1-100. Other parameters are shown in Table 10. <Table 10. Dimensional Parameters Specification > Parameter Specification Unit Dimensional outline 131.7±0.4(H)×87.7±0.4(V)×4.7±0.3(T) mm Weight 61 (typ) / 65 (max.) gram Active area 120.96(H) × 75.60(V) mm Pixel pitch 94.5(H) ×94.5(V) um Number of pixels 1280(H) × 800(V) (1 pixel = R + G + B dots) Back-light Edge side 16-LEDs type ( 2 X 8 Array) pixels 7.2 Clearness and Polarizer Hardness. The surface of the LCD has an clear film to increase visibility and a hard coating to reduce scratching. 7.3 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 350 [lux.] SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 19 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 7.4 Design Guide Give enough clearance (over 0.3mm) Between the Touch Panel and LCD Module glass to protect a display Give enough clearance (over 0.2mm) Between the Case and LCD Module component to protect a display SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 20 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 8.0 RELIABLITY TEST The Reliability test items and its conditions are shown in below. <Table 12. Reliability Test Conditions > No Test Item Conditions 1 High temperature storage test Ta = 60 °C, 240 hrs 2 Low temperature storage test Ta = -20 °C, 240 hrs 3 High temperature & high humidity operation test Ta = 50 ℃, 80%RH, 240hrs 4 High temperature operation test Ta = 50 °C, 240 hrs 5 Low temperature operation test Ta = 0 °C, 240 hrs 6 Thermal shock Ta = -20 °C ↔ 60 °C (30 min), 100 cycle 7 Vibration test (non-operating) Frequency : 10~500Hz Gravity/AMP : 1.5G Period : X,Y,Z 30min 8 Shock test (non-operating) Gravity : 220G Pulse width : 2ms, half sine wave ±X, ±Y, ±Z Once for each direction 9 Electro-static discharge test (non-operating) Air : 150pF, 330ohm, 15KV Contact : 150pF, 330ohm, 8KV SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 21 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 9.0 Product Serial Number 0 1 CP210452-XXXXX HV056WX1-100 HYDIS Barcode 1 2 3 4 5 X X X X X X X 6 X X X 7 X X X X X X X No 1. Control Number No 5. Month (1, 2, 3,…, 9, X, Y, Z) No 2. Rank / Grade No 6. FG Code No 3. Line Classification (HYDIS : H, LCM : L, BOE OT : A/B/C) No 7. Serial Number No 4. Year (8 : 2008, 9 : 2009, …) SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 22 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 10.0 PACKING INFORMATION Hydis provides the standard shipping container for customers, unless customer specifies their packing information. The standard packing method and Barcode information are shown in below. 10.1 Packing Order Module ④ ① Cushion Tray ② Carton ③ ⑤ Sealing bag Box‐label SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 23 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 10.2 Packing Note y Box Dimension : 387 X 335 X 130 mm y Package Quantity in one Box : 10.3 Box label y Label Size : 108 mm (L) X 56 mm (W) y Contents Model : HV056WX1-100 Q`ty : Module Q`ty in one box Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of Product XX HV056WX1-100 200X.X.XX * 0000000000000 * XXXX 00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no SPEC. NUMBER FG CODE RoHS Mark SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 24 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 11.0 HANDLING & CAUTIONS (1) Cautions when taking out the module y Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module y As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. y As the LCD panel and back - light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. y Do not pull the interface connector in or out while the LCD module is operating. y Put the module display side down on a flat horizontal plane. y Handle connectors and cables with care. (3) Cautions for the operation y When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged. y Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. (4) Cautions for the atmosphere y Dew drop atmosphere should be avoided. y Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics y Do not apply fixed pattern data signal to the LCD module at product aging. y Applying fixed pattern for a long time may cause image sticking. (6) Other cautions y Do not disassemble and/or re-assemble LCD module. y Do not re-adjust variable resistor or switch etc. yWhen returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 25 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 12.0 APPENDIX Figure 1. Measurement Set Up Photo detector ( TOPCON BM-5A) o Field = 2 50 cm TFT-LCD module LCD panel Center of the screen Optical characteristics measurement setup Figure 2. White Luminance and Uniformity Measurement Locations (9 points) SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 26 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 Figure 3. Response Time Testing TFT Off(Black) TFT On(White) TFT Off(Black) Td Tr 100% 90% 10% 0% Figure 4. Cross Modulation Test Description VIEW AREA VIEW AREA 320,200 960,200 L31 YB(1120, 400) 320,600 L0 YA (1120, 400) Cross-Talk (%) = 960,600 YB - YA × 100 YB Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 27 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 Figure 5. TFT-LCD Module Outline Dimension (Front View) SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 28 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2011.01.12 Figure 6. TFT-LCD Module Outline Dimension (Rear View) SPEC. NUMBER SPEC TITLE HV056WX1-101 Product Specification B2005-C001-C (3/3) PAGE 29 OF 29 A4(210 X 297)