ROHM BD6726FU

1/4
STRUCTURE
Silicon Monolithic Integrated Circuit
PRODUCT SERIES
Single-Phase Full-Wave Motor Driver for Fan Motor
TYPE
BD6726FU
FEATURES
Pre-driver compatible for external Tr
Speed controllable by DC/PWM input
PWM soft switching drive
Built-in Speed control circuit by rotation speed feedback
〇ABSOLUTE MAXIMUM RATINGS
Symbol
Limit
Parameter
Supply voltage
Vcc
20
Power dissipation
Pd
562.5*
Operating temperature
Topr
-40 to +100
Storage temperature
Tstg
-55 to +150
High side output voltage
VOH
36
Low side output voltage
VOL
15
Low side output current
IOL
10
FG output current
IFG
10
FG output voltage
VFG
20
REF current ability
IREF
8
HB current ability
IHB
8
Input voltage (H+, H-, CS, PWMIN)
VIN
7
ICT and SHIFT current ability
IIN
100
Junction temperature
Tjmax
150
*Reduce by 4.5mW/°C over Ta=25°C.
(On 70.0mm×70.0mm×1.6mm glass epoxy board)
*This product is not designed for production against radioactive rays.
*This document may be strategic data subject to COCOM regulations.
REV. A
Unit
V
mW
°C
°C
V
V
mA
mA
V
mA
mA
V
μA
°C
2/4
〇OPERATING CONDITIONS
Parameter
Operating supply voltage range
Symbol
Vcc
Input voltage range 1 (H+, H-)
VIN1
Input voltage range 2 (PWMIN)
VIN2
Input voltage range 3 (MIN)
Input voltage range 4 (FIL)
VIN3
VIN4
Limit
5.0 to 17.0
0 to Vcc-2.0
0 to 7.0
0 to VREF
0 to 6.5
0 to VREF
0 to VFILH
Unit
V
V
V
V
V
V
V
less than Vcc=9.0V
more than Vcc=9.0V
less than Vcc=7.0V
more than Vcc=7.0V
〇ELECTRICAL CHARACTERISTICS (Unless otherwise specified Ta=25°C, Vcc=12V)
Limit
Symbol
Parameter
Unit
Conditions
Min.
Typ.
Max.
Circuit current
Icc
3.0
5.4
8.0
mA
Hall input hysteresis
VHYS
±5
±10
±15
mV
High side output current
IH
5.0
10.5
17.0
mA VOH=12V
High side output leak current
IHL
10
μA VOH=36V
Low side output high voltage
VLH
9.3
9.5
V
IOL=-5mA
Low side output low voltage
VLL
0.5
0.7
V
IOL=5mA
Lock detection ON time
TON
0.18
0.3
0.42
s
Lock detection OFF time
TOFF
3.6
6.0
8.4
s
FG output low voltage
VFGL
0.3
V
IFG=5mA
FG output leak current
IFGL
10
μA VFG=17V
OSC low voltage
VOSCL
0.8
1.0
1.2
V
OSC high voltage
VOSCH
2.3
2.5
2.7
V
OSC charge current
ICOSC
-50
-32
-20
μA
OSC discharge current
IDOSC
20
32
50
μA
REF voltage
VREF
4.6
5.0
5.4
V
IREF=-2mA
Hall bias voltage
VHB
1.3
1.5
1.7
V
IHB=-2mA
Current limit voltage
VCL
130
160
190
mV
MIN bias current
IMIN
1.0
μA VMIN=0V
CS bias current
ICS
1.0
μA VCS=0V
PWMIN bias current
IPWM
15
25
35
μA VPWMIN=0V
PWMIN input high voltage
VPWMH
2.3
6.5
V
PWMIN input low voltage
VPWML
0.0
1.0
V
FIL output high voltage
VFILH
1.3
1.5
1.7
V
VPWMIN=0V
FIL source current
IFILH
-25
-15
-10
μA VPWMIN=0V
FIL sink current
IFILL
10
15
25
μA VPWMIN=VREF
VCONT charge current
ICVCON
-60
-100
-145
μA
VCONT discharge current
IDVCON
16
11
7
μA
Soft start time
TSS
1.2
2.0
2.8
s
REV. A
3/4
〇PACKAGE OUTLINES
D6726
Lot No.
SSOP-C20 (UNIT:mm)
〇BLOCK DIAGRAM
〇TERMINAL NAME
FG
GND
SIGNAL
OUTPUT
TSD
1
SHIFT
20
PWMIN
SPEED
2
19
CONTROL
FIL
ICT
3
SOFT
START
QUICK
START
SOFT
SWITCH
LOCK
PROTECTION
18
CP
OSC
4
17
H-
MIN
OSC
5
VCONT
+
6
-
HALL
COMP
PWMCOMP
A1H
9
A1L
10
-
HB
+
CONTROL
REF
LOGIC
Vcc
8
16
VCL
REF
7
HB
CURRENT
LIMIT
COMP +
-
15
H+
14
CS
PRE DRIVER
13
A2H
12
A2L
11
REV. A
PIN No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Terminal
name
GND
SHIFT
ICT
OSC
MIN
VCONT
REF
Vcc
A1H
A1L
A2L
A2H
CS
H+
HB
HCP
FIL
PWMIN
FG
4/4
〇CAUTIONS ON USE
1) Absolute maximum ratings
An excess in the absolute maximum rations, such as supply voltage, temperature range of operating conditions, etc., can break down
the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated values will
expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses.
2) Connecting the power supply connector backward
Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply lines. An
external direction diode can be added.
3) Power supply line
Back electromotive force causes regenerated current to power supply line, therefore take a measure such as placing a capacitor
between power supply and GND for routing regenerated current. And fully ensure that the capacitor characteristics have no problem
before determine a capacitor value. (when applying electrolytic capacitors, capacitance characteristic values are reduced at low
temperatures)
4) GND potential
It is possible that the motor output terminal may deflect below GND terminal because of influence by back electromotive force of motor.
The potential of GND terminal must be minimum potential in all operating conditions, except that the levels of the motor outputs
terminals are under GND level by the back electromotive force of the motor coil. Also ensure that all terminals except GND and motor
output terminals do not fall below GND voltage including transient characteristics. Malfunction may possibly occur depending on use
condition, environment, and property of individual motor. Please make fully confirmation that no problem is found on operation of IC.
5) Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
6) Inter-pin shorts and mounting errors
Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any connection error or
if pins are shorted together.
7) Actions in strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction.
8) ASO
When using the IC, set the output transistor so that it does not exceed absolute maximum rations or ASO.
9) Thermal shut down circuit
The IC incorporates a built-in thermal shutdown circuit (TSD circuit). Operation temperature is 175°C (typ.) and has a hysteresis width
of 25°C (typ.). When IC chip temperature rises and TSD circuit works, the output terminal becomes an open state. TSD circuit is
designed only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation. Do not
continue to use the IC after operation this circuit or use the IC in an environment where the operation of this circuit is assumed.
10) Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always
discharge capacitors after each process or step. Always turn the IC’s power supply off before connecting it to or removing it from a jig
or fixture during the inspection process. Ground the IC during assembly steps as an antistatic measure. Use similar precaution when
transporting or storing the IC.
11) GND wiring pattern
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing a single
ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused by large currents
do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern of any external
components, either.
12) Capacitor between output and GND
When a large capacitor is connected between output and GND, if Vcc is shorted with 0V or GND for some cause, it is possible that the
current charged in the capacitor may flow into the output resulting in destruction. Keep the capacitor between output and GND below
100uF.
13) IC terminal input
When Vcc voltage is not applied to IC, do not apply voltage to each input terminal. When voltage above Vcc or below GND is applied
to the input terminal, parasitic element is actuated due to the structure of IC. Operation of parasitic element causes mutual
interference between circuits, resulting in malfunction as well as destruction in the last. Do not use in a manner where parasitic
element is actuated.
REV. A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039A