User Manual AIMB

User Manual
AIMB-562 KIOSK
Intel® LGA775 Core™ 2 Duo
mATX Motherboard with Dual
VGA/LVDS/DDR2/10 COM/LAN
Copyright
The documentation and the software included with this product are copyrighted 2009
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
AWARD is a trademark of Phoenix Technologies Ltd.
IBM and PC are trademarks of International Business Machines Corporation.
Intel® Pentium® M/Celeron® M are trademarks of Intel Corporation.
WinBond is a trademark of Winbond Corporation.
All other product names or trademarks are properties of their respective owners.
AIMB-562 KIOSK User Manual
Part No. 2002056212
Edition 3
Printed in Taiwan
September 2009
ii
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known.
Your satisfaction is our primary concern. Here is a guide to Advantech’s customer
services. To ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every business day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.
iii
AIMB-562 KIOSK User Manual
Declaration of Conformity
FCC
This device complies with the requirements in part 15 of the FCC rules:
Operation is subject to the following two conditions:
This device may not cause harmful interference
This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense. The
user is advised that any equipment changes or modifications not expressly approved
by the party responsible for compliance would void the compliance to FCC regulations and therefore, the user's authority to operate the equipment.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's
instructions.
AIMB-562 KIOSK User Manual
iv
CPU Compatibility
CPU family
sSpec Core
Power
stepping
FSB Mgn tech L2
cache
Advantech
PN
Core2 Duo E7400
2.80GHz EM64T
Dual Core
SLB9Y M0
65W
1066 45nm
3MB
96MP2DD28FA-3M7T
Core2 Duo E6700
2.66GHz EM64T
Dual Core
SL9S7 B2
65W
1066 65nm
4MB
96MP2DD26FA-4M7T
Core2 Duo E6600
2.40GHz EM64T
Dual Core
SL9S8 B2
65W
1066 65nm
4MB
96MP2DD24FA-4M7T
Core2 Duo E6400
2.13GHz EM64T
Dual Core
SL9S9 B2
65W
1066 65nm
2MB
96MP2DD21FA-2M7T
Core2 Duo E6300
1.86GHz EM64T
Dual Core
SL9SA B2
65W
1066 65nm
2MB
96MP2DD18FA-2M7T
Core2 Duo E5300
SLB9U R0
2.6GHz EM64T Dual
Core
65W
800
45nm
2MB
96MPPD2.6F82M7T1
Core2 Duo E4300
SL9TB L2
1.8GHz EM64T Dual
Core
65W
800
65nm
2MB
96MP2DD18F8-2M7T
Pentium Dual-Core
1.8GHz E2160
SLA8Z M0
65W
800
65nm
1MB
96MPPD1.8F8-1M7T
Pentium-D 830
3.00GHz EM64T
Dual Core
SL8CN A0
130W
800
90nm
2MB
96MPPD3.0F8-2M7T
Pentium-4 670
3.80GHz EM64T
SL7Z3 N0
115W
800
90nm
2MB
96MPP43.8F82M7T1
Celeron D E1200
1.6GHz EM64T
SLAQ M0
W
65w
800
65nm
512KB
96MPC21.6F8-5K7T
Celeron-D 352
3.20GHz EM64T
SL96P C1
86W
533
65nm
512KB
96MPCD3.2F5-5K7T
Celeron 440 2GHz
SL9XL A1
35W
800
65nm
512KB
96MPC42.0F8-5K7T
Celeron 430 1.8GHz SL9XN A1
35W
800
65nm
512KB
96MPC41.8F8-5K7T
v
AIMB-562 KIOSK User Manual
Memory Compatibility
Advantech
Memory
PN
Size Speed Type
Apacer
1 GB
DDR2
533
DDR2
N
Transcend
256
MB
DDR2
533
DDR2
N
TS32MLQ6
NA
4V5F
SAMSUNG 443 K4T56083QFGCD5 (32x8)
512
MB
DDR2
533
DDR2
N
NA
NA
infineon HYB18T512 800AF37
FSS43331 (64x8)
1 GB
DDR2
533
DDR2
N
NA
NA
ELPIDA E5108AE-5C-E (64x8)
512
MB
DDR2
533
DDR2
N
96D278.91G66.
ELPIDA E5108AG-5C-E
512M533NN
420
(64x8)
-AP
1 GB
DDR2
533
DDR2
N
96D278.01G66.
1G533NN420
AP
ELPIDA E5108AGBG-6E-E
(64x8)
512
MB
DDR2
667
DDR2
N
78.91G92.
NA
420
ELPIDA E5108AG-6E-E
(64x8)
1 GB
DDR2
667
DDR2
N
78.01G92.
NA
420
ELPIDA E5108AGBG-6E-E
(64x8)
2 GB
DDR2
667
DDR2
N
78.A1G9O. 96D2404
2G667-AP
SEC K4T1G08400 (128x8)
256
MB
DDR2
533
DDR2
N
96D2TS32MLQ6
infineon HYB18T512160AF3.7
256M533NN
4V5M
3VV21710 (32x16)
-TR
512
MB
DDR2
533
DDR2
N
96D2TS64MLQ6
SEC K4T51083QC ZCD5
512M533NN
4V5J
(64X8)
-TR1
512
MB
DDR2
667
DDR2
N
TS6QNJ22
96D2850-6S/
SAMSUNG K4T51083QC
512M667NN
TS64MLQ6
ZCE6 (64x8)
-TR
4V6J
1 GB
DDR2
667
DDR2
N
96D2TS2QNJ23
1G667NN450-6S
TR
SEC K4T51083QE ZCE6
(64x8)
SEC K4T51083QG HCE6
(64x8)
DSL
Apacer
(RoHS)
Transcend
(RoHS)
Transcend
(RoHS)
ECC
Vendor
PN
Brand
78.01066.4 NA
00
SAMSUNG K4T51083QBZKD5 (128x4)
DDR2
1 GB
667
DDR2
N
TS2QNJ23
96D2450-6S/
1G667NNTS128MLQ
TR
64V6J
2 GB
DDR2
667
DDR2
N
TS5QNU23 96D2451-6S
2G667-TR
SAMSUNG K4T1G084QDZCE6 (128x8)
2 GB
DDR2
667
DDR2
N
TS256MLQ
NA
64V6U
Micron 7HE12 D9HNL (128x8)
1 GB
DDR2
800
DDR2
N
TS128MLQ
NA
64V8J
ProMOS V59C1512804QBF25
(64x8)
2 GB
DDR2
667
DDR2
N
TS256MLQ
NA
64V6U
SAMSUNG K4T1G084QAZCE6 (128x8)
AIMB-562 KIOSK User Manual
vi
1 GB
DDR2
667
DDR2
N
NA
NA
ELPIDA E5108AGBG-6E-E
(64x8)
2 GB
DDR2
667
DDR2
N
NA
NA
ELPIDA E1108ACSE-6EE(128x8)
1 GB
DDR2
800
DDR2
N
NA
NA
ELPIDA E5108AHSE-8E-E
(64x8)
2 GB
DDR2
800
DDR2
N
NA
NA
ELPIDA E1108ACBG-8E-E
(128x8)
2 GB
DDR2
667
DDR2
N
KVR667D2
NA
N5/2G
Micron 7KE12 D9HNL (128x8)
1GB
DDR2
800
DDR2
N
KVR800D2
NA
N5/1G
ELPIDA E5108AHSE-8E-E
(64x8)
DSL
Kingston
(RoHS)
Ordering Information
AIMB-562 KIOSK Ordering Information
Part Number
On-board Chipset
Processor
Memory
AIMB-562VG-KSA1E
NA
945G
AIMB-562VG-GRA1E
NA
AIMB-562L-KSA1E
NA
LAN
COM
Display
DDR2 533/ 1
667
10
CRT/CRT/
LVDS
945G
DDR2 533/ 1
667
10
CRT/CRT
945GC
DDR2 533/ 1
667
10
CRT
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
vii
AIMB-562 KIOSK User Manual
5.
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Initial Inspection
Before you begin installing your motherboard, please make sure that the following
materials have been shipped:

LGA 775 CoreTM 2 Duo/Pentium 4/Pentium dual-core/Celeron® D Processorbased Micro ATX with DDR2/PCIe/Single GbE LAN
1 x AIMB-562 KIOSK startup manual
1 x CD with driver utility and manual
2 x Serial ATA HDD data cable
2 x Serial ATA HDD power cable
4 x Com port cable kit
1 x I/O port bracket
1 x jumper package
1 x warranty card
If any of these items are missing or damaged, contact your distributor or sales representative immediately. We have carefully inspected the AIMB-562 KIOSK mechanically and electrically before shipment. It should be free of marks and scratches and in
perfect working order upon receipt. As you unpack the AIMB-562 KIOSK, check it for
signs of shipping damage. (For example, damaged box, scratches, dents, etc.) If it is
damaged or it fails to meet the specifications, notify our service department or your
local sales representative immediately. Also notify the carrier. Retain the shipping
carton and packing material for inspection by the carrier. After inspection, we will
make arrangements to repair or replace the unit.
AIMB-562 KIOSK User Manual
viii
Contents
Chapter
1
General Information ............................1
1.1
1.2
1.3
1.9
1.10
1.11
1.12
Introduction ............................................................................................... 2
Features .................................................................................................... 2
Specifications ............................................................................................ 3
1.3.1 System .......................................................................................... 3
1.3.2 Memory ......................................................................................... 3
1.3.3 Input/Output .................................................................................. 3
1.3.4 Graphics........................................................................................ 3
1.3.5 Ethernet LAN ................................................................................ 3
1.3.6 Industrial features ......................................................................... 3
1.3.7 Mechanical and environmental specifications............................... 3
Jumpers and Connectors .......................................................................... 4
Table 1.1: Jumpers...................................................................... 4
Table 1.2: Connectors ................................................................. 4
Board layout: Jumper and Connector Locations ....................................... 5
Figure 1.1 Jumper and Connector Location ................................ 5
Figure 1.2 I/O Connectors ........................................................... 6
AIMB-562 KIOSK Block Diagram.............................................................. 6
Figure 1.3 AIMB-562 KIOSK Block Diagram ............................... 6
Safety Precautions .................................................................................... 7
Jumper Settings ........................................................................................ 8
1.8.1 How to set jumpers ....................................................................... 8
1.8.2 CMOS clear (CMOS1) .................................................................. 8
Table 1.3: CMOS1....................................................................... 8
1.8.3 Volumn adjustment(VOLADJ1)..................................................... 8
Table 1.4: VOLADJ1.................................................................... 8
1.8.4 Chassis instruction connector (JCASE1) ...................................... 9
1.8.5 ATX/AT mode selector (PSON1) .................................................. 9
Table 1.5: ATX/AT mode selector (PSON1)................................ 9
1.8.6 AT switch connector(AT_SWITCH1) ............................................ 9
1.8.7 COM3/7 RS 232/422/485 mode selector (JSETCOM3456/78910)
...................................................................................................... 9
Table 1.6: COM3456/78910 RS 232/422/485 mode selector
(JSETCOM3456/78910) ............................................. 9
1.8.8 LVDS power jumper connector(JLVDSPWR1) ........................... 10
Table 1.7: LVDS power jumper selectior ................................... 10
System Memory ...................................................................................... 10
Memory Installation Procedures.............................................................. 10
Cache Memory........................................................................................ 10
Processor Installation.............................................................................. 10
2
Connecting Peripherals ....................11
2.1
2.2
2.3
Introduction ............................................................................................. 12
Parallel Port (LPT1)................................................................................. 12
USB Ports (USB12/LAN2_USB34/USB56/USB78) ................................ 13
Table 2.1: LAN LED Indicator.................................................... 13
VGA Connector (VGA1/VGA2) ............................................................... 14
Serial Ports (COM1~COM10) ................................................................. 15
PS/2 Keyboard and Mouse Connector (KBMS1) .................................... 16
CPU Fan Connector (CPU_FAN1).......................................................... 17
System FAN Connector (SYS_FAN1)..................................................... 18
Front Panel Connectors (JFP1) .............................................................. 19
2.9.1 Power/Sleep Waiting LED (JFP1)............................................... 19
1.4
1.5
1.6
1.7
1.8
Chapter
2.4
2.5
2.6
2.7
2.8
2.9
ix
AIMB-562 KIOSK User Manual
Chapter
Chapter
Chapter
Chapter
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
2.18
2.19
2.20
2.21
2.22
Table 2.2: ATX power supply LED status (No support for AT power) ............................................................................. 19
2.9.2 Reset Connector (JFP1 pins 5 & 7) ............................................ 20
2.9.3 HDD LED Connector (JFP1 pins 1 & 3)...................................... 20
2.9.4 ATX Soft Power Switch (JFP1 pins 6 & 8).................................. 20
Line In, Line Out, Mic In Connector (AUDIO1)........................................ 20
Serial ATA Interface (SATA1, SATA2).................................................... 21
ATX Power Connector (ATX12V1, EATXPWR1).................................... 22
SPI Flash Connector (SPI_CN1) ............................................................ 23
Front Panel Audio Connector (FPAUDIO1) ............................................ 24
System FAN Connector (SYS_FAN2) .................................................... 25
Primary EIDE Connector (IDE1) ............................................................. 25
USB 2.0 Connector (USB 56, 78) ........................................................... 26
LVDS Connector (JLVDS1) .................................................................... 27
LVDS Backlight Enabler (JBL1) .............................................................. 27
LVDS Power Jumper Selection1 (JLVDSPWR1).................................... 28
Volume Adjustment Connector (VOLADJ1)............................................ 28
GPIO Pin Header (GPIO1, GPIO2)......................................................... 29
3
BIOS Operation ................................. 31
3.1
3.2
Introduction ............................................................................................. 32
BIOS Setup ............................................................................................. 32
3.2.1 Main Menu .................................................................................. 33
3.2.2 Standard CMOS Features .......................................................... 34
3.2.3 Advanced BIOS Features ........................................................... 35
3.2.4 Advanced Chipset Features ....................................................... 36
3.2.5 Integrated Peripherals ................................................................ 38
3.2.6 Security Chip Configuration ........................................................ 40
3.2.7 TPM Support............................................................................... 40
3.2.8 Power Management Setup ......................................................... 41
3.2.9 PnP/PCI Configurations.............................................................. 43
3.2.10 PC Health Status ........................................................................ 44
3.2.11 Load Setup Defaults ................................................................... 45
3.2.12 Set Password.............................................................................. 45
3.2.13 Save & Exit Setup....................................................................... 47
3.2.14 Quit without Saving..................................................................... 47
4
Chipset Software Installation Utility 49
4.1
4.2
4.3
Before you begin..................................................................................... 50
Introduction ............................................................................................. 50
Windows XP Driver Setup....................................................................... 51
5
VGA Setup ......................................... 53
5.1
5.2
Introduction ............................................................................................. 54
Windows Vista/XP/2000.......................................................................... 54
6
LAN Configuration ............................ 57
6.1
6.2
6.3
6.4
Introduction ............................................................................................. 58
Features.................................................................................................. 58
Installation............................................................................................... 58
Win XP/Vista Driver Setup (Realtek RTL8111C) .................................... 58
AIMB-562 KIOSK User Manual
x
Appendix A
Programming the Watchdog Timer..61
A.1
Programming the Watchdog Timer ......................................................... 62
A.1.1 Watchdog timer overview............................................................ 62
A.1.2 Programming the Watchdog Timer ............................................. 62
Table A.1: Watchdog Timer Registers ....................................... 64
A.1.3 Example Program ....................................................................... 65
Appendix B
I/O Pin Assignments..........................69
B.1
Parallel Port (LPT1)................................................................................. 70
Table B.1: Parallel Port (LPT1) .................................................. 70
USB Header (USB56) ............................................................................. 70
Table B.2: USB Header (USB56)............................................... 70
USB Header (USB78) ............................................................................. 71
Table B.3: USB Header (USB78)............................................... 71
VGA Connector (VGA1) .......................................................................... 71
Table B.4: VGA Connector (VGA1) ........................................... 71
VGA Connector (VGA2) .......................................................................... 72
Table B.5: VGA Connector (VGA2) ........................................... 72
RS-232 Interface (COM1-COM2)............................................................ 72
Table B.6: RS-232 Interface (COM1~COM2) ............................ 72
RS-232/422/485 Setting Interface (JETCOM3456~78910)..................... 73
Table B.7: RS-232/422/485 Setting Interface
(JETCOM3456~78910) ............................................ 73
RS-232 Interface (COM3456) ................................................................. 73
Table B.8: RS-232 Interface(3456) ............................................ 73
RS-232 Interface (COM78910) ............................................................... 74
Table B.9: RS-232 Interface (COM78910)................................. 74
SPI_CN1: SPI fresh card pin connector.................................................. 75
Table B.10:SPI_CN1:SPI fresh card pin connector .................... 75
PS/2 Keyboard and Mouse Connector (KBMS1) .................................... 75
Table B.11:PS/2 Keyboard and Mouse Connector (KBMS1) ..... 75
CPU Fan Power Connector (CPU_FAN1) .............................................. 76
Table B.12:CPU Fan Power Connector (CPU_FAN1)................ 76
System Fan Power Connector (SYS_FAN1/SYS_FAN2) ....................... 76
Table B.13:System Fan Power Connector (SYSFAN1/SYSFAN2)
.................................................................................. 76
Front Panel Connectors (JFP1) .............................................................. 76
B.14.1 Power/Sleep LED (JFP1)............................................................ 77
Table B.14:Power/Sleep LED (JFP1) ......................................... 77
B.14.2 Reset Connector (JFP1) ............................................................. 77
Table B.15:Reset Connector (JFP1)........................................... 77
B.14.3 HDD LED Connector (JFP1)....................................................... 77
Table B.16:HDD LED Connector (JFP1) .................................... 77
B.14.4 ATX Soft Power Switch (JFP1) ................................................... 77
Table B.17:ATX Soft Power Switch (JFP1)................................. 77
ATX1 12 V Auxiliary Power Connector (ATX12V1)................................. 78
Table B.18:ATX1 12 V Auxiliary Power Connector (ATX12V1) .. 78
ATX Power Connector (EATXPWR1) ..................................................... 78
Table B.19:ATX Power Connector (ATX2) ................................. 78
USB/LAN ports (LAN2_USB12/USB34).................................................. 79
Table B.20:USB Port................................................................... 79
Table B.21:Ethernet 10/100Base-T RJ-45 Port .......................... 79
Line Out, Mic In Connector (AUDIO1)..................................................... 79
Serial ATA0 (SATA1) .............................................................................. 79
Table B.22:Serial ATA0 (SATA1)................................................ 79
Serial ATA1 (SATA2) .............................................................................. 80
Table B.23:Serial ATA1 (SATA2)................................................ 80
B.2
B.3
B.4
B.5
B.6
B.7
B.8
B.9
B.10
B.11
B.12
B.13
B.14
B.15
B.16
B.17
B.18
B.19
B.20
xi
AIMB-562 KIOSK User Manual
B.21
B.22
B.23
B.24
B.25
B.26
B.27
B.28
B.29
B.30
B.31
B.32
AT/ATX Mode (PSON1).......................................................................... 80
Table B.24:AT/ATX Mode (PSON1) ........................................... 80
JLVDS1: LVDS connector....................................................................... 80
Table B.25:LVDS Connector (JLVDS1)...................................... 80
JBL1(LVDS inverter connector) .............................................................. 81
Table B.26:LCD Inverter Power Connector (JBL1)..................... 81
JLVDSPWR1(LVDS power jumper selection)......................................... 81
Table B.27:LVDS power jumper selection (JLVDSPWR1) ......... 81
FPAUDIO1(Front Panel Audio Connector) ............................................. 81
Table B.28:Front Panel Audio Connector (FPAUDIO1).............. 81
GPIO12(GPIO pin header)...................................................................... 82
Table B.29:GPIO pin header(GPIO1) ......................................... 82
Table B.30:GPIO pin header(GPIO2) ......................................... 82
VOLADJ1(Volumn Adjustment connector).............................................. 82
Table B.31:Volumn Adjustment connector (VOLADJ1) .............. 82
System I/O Ports..................................................................................... 82
Table B.32:System I/O Ports ...................................................... 82
JCASE1(Open Case Connector) ............................................................ 83
Table B.33:Case Open Connector(JCASE1).............................. 83
DMA Channel Assignments .................................................................... 83
Table B.34:DMA Channel Assignments ..................................... 83
Interrupt Assignments ............................................................................. 84
Table B.35:Interrupt Assignments .............................................. 84
1st MB Memory Map............................................................................... 84
Table B.36:1st MB Memory Map ................................................ 84
AIMB-562 KIOSK User Manual
xii
Chapter
1
1
General Information
1.1 Introduction
The AIMB-562 KIOSK is designed with the Intel® 945G/945GC and the ICH7 for
industrial applications that require both performance computing and enhanced power
management capabilities. The motherboard supports Intel Pentium LGA 775 CoreTM
2 Duo up to 2.8 GHz / Pentium dual-core up to 2.2 Ghz / Pentium 4 up to 3.4 GHz/
Celeron® D up to 2.0 Ghz with 533/800/1066 MHz front side bus and DDR2 533/667
MHz up to 2 GB.
The AIMB-562 KIOSK offers cost-saving integrated graphics, built on the Intel®
945G/945GC chipset and features the unique Intel® Extreme Graphics architecture
that maximizes VGA performance and shares system memory up to 224 MB.
Advantech AIMB-562 KIOSK is designed with an Intel 945G/945GC chipset and supports Intel Core 2 Duo processor up to FSB 1066 MHz. A rich I/O connectivity of 10
serial ports, 8 USB 2.0, single GbE LAN and 2 SATA ports.
1.2 Features

Cost effective 945G/945GC chipset: support 533/800/1066 Front side bus
Rich I/O connectivity: 10 serial ports, 8 USB 2.0, single GbE LAN
Standard Micro ATX form factor with industrial feature: The AIMB-562
KIOSK is the most fully-featured Micro ATX motherboard with balanced expandability and the performance
Wide selection of storage devices: SATA HDD, customers benefit the flexibility of using the most suitable storage device for large capacity
Optimized integrated graphic solution: With Intel® Graphics Media Accelerator 950, it supports versatile display options and 32-bit 3D graphics engine.
AIMB-562 KIOSK User Manual
2
1.3.1 System

1.3.2 Memory

RAM: Up to 4 GB in 2 slots 240-pin SODIMM sockets. Supports dual channel
DDRII 533/667 SDRAM
1.3.3 Input/Output

PCIe bus: 1PCIe x 4 slot
Enhanced parallel port: Configured to LPT1 with 25 pin box header. Supports
EPP/SPP/ECP
Serial ports: Ten serial ports, two of RS-232/422/485 and eight of RS-232 serial
ports
Keyboard and PS/2 mouse connector: Two 6-pin mini-DIN connectors are
located on the mounting bracket for easy connection to a PS/2 keyboard and
mouse
USB port: Supports up to eight USB 2.0 ports with transmission rate up to 480
Mbps, 4 on board pin header and 4 external ports)
1.3.4 Graphics

Controller: Chipset integrated VGA controller
Display memory: Dynamically shared system memory up to 224 MB
CRT: Up to 2048 x 1536 resolution, 400 MHz RAMDAC
1.3.5 Ethernet LAN

Supporting single/dual 10/100/1000Base-T Ethernet port (s) via PCI Express x1
bus which provides 500 MB/s data transmission rate
Controller: LAN: Realtek RTL8111C
1.3.6 Industrial features

Watchdog timer: Can generate a system reset. The watchdog timer is programmable, with each unit equal to one second or one minute (255 levels)
1.3.7 Mechanical and environmental specifications

Operating temperature: 0 ~ 60° C (32 ~ 140° F, Depending on CPU)
Storage temperature: -20 ~ 70° C (-4 ~ 158° F)
Humidity: 5 ~ 95% non-condensing
Power supply voltage: +3.3 V, +5 V, +12 V, -12 V, 5 Vsb
3
AIMB-562 KIOSK User Manual
General Information
CPU: LGA 775 CoreTM 2 Duo up to 2.8 Ghz / Pentium dual-core up to 2.2 Ghz /
Pentium 4 up to 3.4 Ghz / Celeron® D up to 2.0 Ghz
BIOS: Award SPI 16 Mbit BIOS
System chipset: Intel 945G/945GC with ICH7
SATA hard disk drive interface: Two on-board SATA connectors with data
transmission rate up to 300 MB
Chapter 1
1.3 Specifications

Power consumption:
+5 V @ 4 A, +3.3 V @ 1.02 A, +12 V @ 2.35 A, 5 VSB @ 0.26 A, -12 V @ 0.12
A Measure the maximum current value which system under maximum load
(CPU: Top speed, RAM & Graphic: Full loading)
Board size: 244 mm x 244 mm (9.6" x 9.6")
Board weight: 0.75 kg
1.4 Jumpers and Connectors
Connectors on the AIMB-562 KIOSK motherboard link it to external devices such as
hard disk drives and a keyboard. In addition, the board has a number of jumpers
used to configure your system for your application.
The tables below list the function of each of the board jumpers and connectors. Later
sections in this chapter give instructions on setting jumpers. Chapter 2 gives instructions for connecting external devices to your motherboard.
Table 1.1: Jumpers
Label
Function
CMOS1
CMOS clear
JCASE1
Chassis Instruction Connector
PSON1
AT/ATX mode selector
JSETCOM3456
Serial port:RS232/RS422/RS485 jumper setting
JSETCOM78910
Serial port:RS232/RS422/RS485 jumper setting
JLVDSPWR1
LVDS Power Jumpr Selection
VOLADJ1
Volumn adjustment connector
Table 1.2: Connectors
Label
Function
Reset connector
JFP1
HDD LED connector
ATX soft power switch (PS_ON)
Power/Sleep waiting LED
LPT1
Parallel port
USB56
USB port 5, 6 (on board)
USB78
USB port 7 8(on board)
VGA1
VGA connector
VGA2
2nd VGA connector
COM1/COM2
Serial port: COM1/COM2 (9-pin connector)
COM3~6/COM7~10
Serial port: COM3~-6/COM7~10 (40-pin connector)
KBMS1
PS/2 keyboard and Mouse connector
Cable length: 20 meter
CPU_FAN1
CPU FAN connector
SYS_FAN1
System FAN connector 1
USB12
USB port 1,2
LAN2_USB34
LAN2/USB port 3,4
SATA1
Serial ATA0
SATA2
Serial ATA1
AIMB-562 KIOSK User Manual
4
ATX 12 V Auxiliary power connector
EATXPWR1
ATX power connector
SPI_CN1
SPI flash card pin header
AUDIO1
Line Out, Mic IN connector
FPAUDIO1
Front Panel audio connector (FP_AUDIO)
GPIO1
GPIO pin header (SMD pitch=2.0 mm) 2 x 4
GPIO2
GPIO pin header (SMD pitch=2.0 mm) 2 x 4
JLVDS1
LVDS connector
JLVDSPWR1
LVDS power jumper selection1-2:3.3 V 2-3:5 V
JBL1
LVDS inverter connector
SYS_FAN2
System Fan connector 2
VOLADJ1
Volume adjustment connector
AT_SWITCH1
AT Switch power connector
1.5 Board layout: Jumper and Connector Locations
Figure 1.1 Jumper and Connector Location
5
AIMB-562 KIOSK User Manual
General Information
ATX12V1
Chapter 1
Table 1.2: Connectors
Figure 1.2 I/O Connectors
1.6 AIMB-562 KIOSK Block Diagram
Intel 945G/945GC
GMCH
Figure 1.3 AIMB-562 KIOSK Block Diagram
AIMB-562 KIOSK User Manual
6
Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open
the PC chassis.
Caution! The computer is provided with a battery-powered Real-time Clock circuit. There is a danger of explosion if battery is incorrectly replaced.
Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to manufacturer's instructions.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s
instructions.
7
AIMB-562 KIOSK User Manual
General Information
Caution! Always ground yourself to remove any static charge before touching the
motherboard. Modern electronic devices are very sensitive to electrostatic discharges. As a safety precaution, use a grounding wrist strap at
all times. Place all electronic components on a static-dissipative surface
or in a static-shielded bag when they are not in the chassis.
Chapter 1
1.7 Safety Precautions
1.8 Jumper Settings
This section provides instructions on how to configure your motherboard by setting
the jumpers. It also includes the motherboards's default settings and your options for
each jumper.
1.8.1 How to set jumpers
You can configure your motherboard to match the needs of your application by setting the jumpers. A jumper is a metal bridge that closes an electrical circuit. It consists
of two metal pins and a small metal clip (often protected by a plastic cover) that slides
over the pins to connect them. To “close” (or turn ON) a jumper, you connect the pins
with the clip. To “open” (or turn OFF) a jumper, you remove the clip. Sometimes a
jumper consists of a set of three pins, labeled 1, 2, and 3. In this case you connect
either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when setting jumpers.
1.8.2 CMOS clear (CMOS1)
The AIMB-562 KIOSK motherboard contains a jumper that can erase CMOS data
and reset the system BIOS information. Normally this jumper should be set with pins
1-2 closed. If you want to reset the CMOS data, set J1 to 2-3 closed for just a few
seconds, and then move the jumper back to 1-2 closed. This procedure will reset the
CMOS to its default setting.
Table 1.3: CMOS1
Function
Jumper Setting
1
*Keep CMOS data
1-2 closed
1
Clear CMOS data
2-3 closed
*default setting
1.8.3 Volumn adjustment(VOLADJ1)
Table 1.4: VOLADJ1
Function
Jumper Setting
*aduio from LINE_OUT 1-2 closed, 4-5 closed
1
2
3
4
5
Caution! The volume output from LINE_OUT has been amplified so please be
cautious when use earphone. Jumper 1-2 & 4-5 can be removed if user
need sound from LINE_OUT with a tuner.
AIMB-562 KIOSK User Manual
8
The AIMB-562 KIOSK motherboard contains a jumper that offer a chassis open sensor. The buzzer on the motherboad beeps when the case is opened.
1.8.5 ATX/AT mode selector (PSON1)
Chapter 1
1.8.4 Chassis instruction connector (JCASE1)
Table 1.5: ATX/AT mode selector (PSON1)
Jumper Setting
AT mode
1-2 closed
*ATX mode
2-3 closed
*default setting
1.8.6 AT switch connector(AT_SWITCH1)
The AT switch connector for AIMB-562 KIOSK is default with 1-2 pin closed for only customer
who use AT switch power supply.
1.8.7 COM3/7 RS 232/422/485 mode selector (JSETCOM3456/78910)
Users can use JSETCOM3456/78910 to select among RS 232/422/485 modes for
COM3 and COM7. The default setting is RS 232.
RS232
RS422
RS485
Table 1.6: COM3456/78910 RS 232/422/485 mode selector
(JSETCOM3456/78910)
Function
Jumper Setting
*RS232
(5-6) + (7-9) + (8-10) + (13-15) + (14-16) closed
RS422
(3-4) + (9-11) + (10-12) + (15-17) + (16-18) closed
RS-485
(1-2) + (9-11) + (10-12) + (15-17) + (16-18) closed
*: Default
9
AIMB-562 KIOSK User Manual
General Information
Function
1.8.8 LVDS power jumper connector(JLVDSPWR1)
JLVDSPWR1 is the jumper for either 3.3 V or 5 V output when connector to LCD
panel.
Table 1.7: LVDS power jumper selectior
Function
Jumper Setting
connect to 3.3 V
1-2 pin closed
connect to 5 V
2-3 pin closed
1.9 System Memory
The AIMB-562 KIOSK has two sockets for 240-pin SODIMMx2.
All these sockets use 1.8 V unbuffered double data rate synchronous DRAMs (DDR2
SDRAM). They are available in capacities of 512 and 1024 MB. The sockets can be
filled in any combination with DIMMs of any size, giving a total memory size between
512 MB and 2 GB. AIMB-562 KIOSK does NOT support ECC (error checking and
correction).
1.10 Memory Installation Procedures
To install SODIMMs, first make sure the two handles of the SODIMM socket are in
the “open” position. i.e. The handles lean outward. Slowly slide the SODIMM module
along the plastic guides on both ends of the socket. Then press the SODIMM module
right down into the socket, until you hear a click. This is when the two handles have
automatically locked the memory module into the correct position of the SODIMM
socket. To remove the memory module, just push both handles outward, and the
memory module will be ejected by the mechanism in the socket.
1.11 Cache Memory
The AIMB-562 KIOSK supports a CPU with one of the following built-in full speed L2
caches:
2048 MB for Intel Core 2 Duo CPU
1024 KB for Pentium dual core
1024 KB / 2048 KB for Pentium 4 CPUs
512 KB for Celeron D CPUs
The built-in second-level cache in the processor yields much higher performance
than conventional external cache memories.
1.12 Processor Installation
The AIMB-562 KIOSK is designed for LGA775, Intel Pentium 4, Intel Core 2 Duo,
Celeron D and Intel Pentium dual core D processor.
AIMB-562 KIOSK User Manual
10
Chapter
2
Connecting
Peripherals
2
2.1 Introduction
You can access most of the connectors from the top of the board as it is being
installed in the chassis. If you have a number of cards installed or have a packed
chassis, you may need to partially remove the card to make all the connections.
2.2 Parallel Port (LPT1)
LPT1
The parallel port is normally used to connect the motherboard to a printer. The AIMB562 KIOSK includes an onboard parallel port, accessed through a 25-pin flat-cable
connector, LPT1.
Note!
Parallel cable is not enclosed in the box as a standard accessory. The
order part number is 1700008809.
AIMB-562 KIOSK User Manual
12
The AIMB-562 KIOSK provides up to eight ports of USB (Universal Serial Bus). The
USB interface complies with USB Specification Rev. 2.0 supporting transmission
rates up to 480 Mbps and is fuse protected. The USB interface can be disabled in the
system BIOS setup.
The AIMB-562 KIOSK is equipped with one high-performance 1000 Mbps Ethernet
LAN. They are supported by all major network operating systems. The RJ-45 jacks
on the rear plate provide 1000Base-T operation.
USB56/78
Table 2.1: LAN LED Indicator
LAN Mode
Lan Indicator
1 Gbps Link on
LED1 Green on
100 Mbps Link on
LED1 Orange on
Active
LED2 Green flash
13
AIMB-562 KIOSK User Manual
Connecting Peripherals
USB12 LAN2_USB34
Chapter 2
2.3 USB Ports (USB12/LAN2_USB34/USB56/USB78)
2.4 VGA Connector (VGA1/VGA2)
VGA1/VGA2
The AIMB-562 KIOSK includes a VGA interface that can drive conventional CRT displays. VGA1/VGA2 is a standard 15-pin D-SUB connector commonly used for VGA.
Pin assignments for CRT connector VGA1/VGA2 are detailed in Appendix B.
AIMB-562 KIOSK User Manual
14
Chapter 2
2.5 Serial Ports (COM1~COM10)
COM2
1 3
37 39
2 4
38 40
COM 3456/78910
AIMB-562 KIOSK supports ten serial ports - eight RS-232, and two RS-232/422/485 COM3 and COM7. The user can use JSETCOM3/7 to select among RS 232/422/485
modes for COM3 and COM7. These ports can connect to serial devices, such as a
mouse or a printer, or to a communications network.
The IRQ and address ranges for both ports are fixed. However, if you want to disable
the port or change these parameters later, you can do this in the system BIOS setup.
Different devices implement the RS-232/422/485 standards in different ways. If you
are having problems with a serial device, be sure to check the pin assignments for
the connector.
15
AIMB-562 KIOSK User Manual
Connecting Peripherals
COM1/COM2
2.6 PS/2 Keyboard and Mouse Connector (KBMS1)
KBMS1
Two 6-pin mini-DIN connectors (KBMS1) on the motherboard provide connection to a
PS/2 keyboard and a PS/2 mouse, respectively.
AIMB-562 KIOSK User Manual
16
Chapter 2
2.7 CPU Fan Connector (CPU_FAN1)
CPU_FAN1
If a fan is used, this connector supports cooling fans of 500 mA (6 W) or less.
17
AIMB-562 KIOSK User Manual
Connecting Peripherals
1
2.8 System FAN Connector (SYS_FAN1)
1
2
3
SYS_FAN1
If a fan is used, this connector supports cooling fans of 500 mA (6 W) or less.
AIMB-562 KIOSK User Manual
18
There are several external switches to monitor and control the AIMB-562 KIOSK.
B
5 and 7
Reset switch
C
1 and 3
Hard drive activity LED
D
2 and 4
Power/Sleep/Waiting LED
E
6 and 8
Power switch
2.9.1 Power/Sleep Waiting LED (JFP1)
JFP1 pins 2 & 4 is a 2-pin connector for the power LED. Refer to Appendix B for
detailed information on the pin assignments. If a PS/2 or ATX power supply is used,
the system's power LED status will be as indicated below:
Table 2.2: ATX power supply LED status (No support for AT power)
Power mode
LED
(ATX Power Mode)
(On/off by
tentative button)
LED
(AT power Mode)
(On/off by switching
power supply)
LED
(AT power Mode)
(On/off by front
panel switch)
PSON1
(On Back plane)
Jumper setting
2-3 pin closed
1-2 pin closed
Connect 1-2 pin cable
with switch
System On
On
On
On
System Suspend
Fast flashes
Fast flashes
Fast flashes
System Off
Slow flashes
Off
Off
19
AIMB-562 KIOSK User Manual
Connecting Peripherals
JFP1
Chapter 2
2.9 Front Panel Connectors (JFP1)
2.9.2 Reset Connector (JFP1 pins 5 & 7)
Many computer cases offer the convenience of a reset button. Connect the wire from
the reset button.
2.9.3 HDD LED Connector (JFP1 pins 1 & 3)
You can connect an LED to connector JFP2 to indicate when the HDD is active.
2.9.4 ATX Soft Power Switch (JFP1 pins 6 & 8)
If your computer case is equipped with an ATX power supply, you should connect the
power on/off button on your computer case to JFP1 pins 1&2. This connection
enables you to turn your computer on and off.
2.10 Line In, Line Out, Mic In Connector (AUDIO1)
Line In
Line Out
Mic In
AUDIO1
AIMB-562 KIOSK User Manual
20
AIMB-562 KIOSK features two high performance serial ATA interface (up to 300 MB/
s) which eases cabling to hard drives with thin and long cables.
21
AIMB-562 KIOSK User Manual
Connecting Peripherals
SATA1, SATA2
Chapter 2
2.11 Serial ATA Interface (SATA1, SATA2)
2.12 ATX Power Connector (ATX12V1, EATXPWR1)
These connectors are for ATX power supply plugs. The power supply plugs are
designed to fit these connectors in only one orientation. Find the proper orientation
and push down firmly until the connectors completely fit.
ATX12V
EATXPWR1
Note!
1.
2.
Make sure that your ATX 12V power supply can provide 8A on the
+12V lead and at least 1A on the +5-volt standby lead (+5VSB).
The minimum recommended wattage is 230W, or 300W for a fully
configured system. The system can become unstable and might
experience difficulty powering up if the power supply is inadequate.
You must install a PSU with a higher power rating if you intend to
install additional devices.
AIMB-562 KIOSK User Manual
22
Chapter 2
2.13 SPI Flash Connector (SPI_CN1)
23
AIMB-562 KIOSK User Manual
Connecting Peripherals
SPI flash card pin header which can be used to flash the BIOS.
2.14 Front Panel Audio Connector (FPAUDIO1)
This connector is for a chassis_mounted front panel audio I/O module that supports
either HD Audio or legacy AC'97 (optional) audio standard. Connect one end of the
front panel audio I/O module cable to this connector.
Note!
For motherboards with the optional HD Audio feature, we recommend
that you connect a high-definition front panel audio module to this connector to avail of the motherboardís high?definition audio capability.
AIMB-562 KIOSK User Manual
24
Chapter 2
2.15 System FAN Connector (SYS_FAN2)
Connecting Peripherals
GND
+12V
+5V
2.16 Primary EIDE Connector (IDE1)
1 3
25
37 39
AIMB-562 KIOSK User Manual
2.17 USB 2.0 Connector (USB 56, 78)
These connectors are for USB 2.0 ports. Connect the USB/GAME module cable to
any of these connectors, then install the module to a slot opening at the back of the
system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.
Note!
The USB module is purchased separately.
AIMB-562 KIOSK User Manual
26
Chapter 2
2.18 LVDS Connector (JLVDS1)
Connecting Peripherals
2.19 LVDS Backlight Enabler (JBL1)
27
AIMB-562 KIOSK User Manual
2.20 LVDS Power Jumper Selection1 (JLVDSPWR1)
3
2
1
2.21 Volume Adjustment Connector (VOLADJ1)
5
Note!
4
3
2
1
The volumn adjustment cable can be used to control the volumn. The
cable need bought separately.
AIMB-562 KIOSK User Manual
28
Chapter 2
2.22 GPIO Pin Header (GPIO1, GPIO2)
Note!
GPIO1 Pin 1 ~ Pin 8 current: GPI: 5V 1uA. GPO: 5V 8~ 10uA.
GPIO2 Pin 1, 3, 5,7 current: GPO(output current only):5V,200mA
Pin 2, 4, 6, 8 current: GPI 5V, 1uA. GPO:5V, 8~10uA
GPIO2 Pin 1,3,5,7 are for 200mAT high current output use only.
29
AIMB-562 KIOSK User Manual
Connecting Peripherals
1
AIMB-562 KIOSK User Manual
30
Chapter
3
BIOS Operation
3
3.1 Introduction
Advantech provides full-featured AwardBIOS 6.0 and delivers the superior performance, compatibility and functionality that manufactures of Industry PC and Embedded boards, its many options and extensions let you customize your products to a
wide range of designs and target markets.
The modular, adaptable AwardBIOS 6.0 supports the broadest range of third-party
peripherals and all popular chipsets, plus Intel, AMD, nVidia, VIA, and compatible
CPUs from 386 through Pentium and AMD Geode, K7 and K8 (including multiple processor platforms), and VIA Eden C3 and C7 CPU.
You can use Advantech’s utilities to select and install features to suit your designs for
customers need.
3.2 BIOS Setup
The AIMB-562 KIOSK KIOSK Series system has build-in AwardBIOS with a CMOS
SETUP utility which allows user to configure required settings or to activate certain
system features.
The CMOS SETUP saves the configuration in the CMOS RAM of the motherboard.
When the power is turned off, the battery on the board supplies the necessary power
to the CMOS RAM.
When the power is turned on, press the <Del> button during the BIOS POST (PowerOn Self Test) will take you to the CMOS SETUP screen.
Control Keys
< ↑ >< ↓ >< ← >< → >
Move to select item
<Enter>
Select Item
<Esc>
Main Menu - Quit and not save changes into CMOS
Sub Menu - Exit current page and return to Main Menu
<Page Up/+>
Increase the numeric value or make changes
<Page Down/->
Decrease the numeric value or make changes
<F1>
General help, for Setup Sub Menu
<F2>
Item Help
<F5>
Load Previous Values
<F7>
Load Setup Default
<F10>
Save all CMOS changes
AIMB-562 KIOSK User Manual
32
Press <Del> to enter AwardBIOS CMOS Setup Utility, the Main Menu will appear on
the screen. Use arrow keys to select among the items and press <Enter> to accept or
enter the sub-menu.
Chapter 3
3.2.1 Main Menu
BIOS Operation

Standard CMOS Features
This setup page includes all the items in standard compatible BIOS.
Advanced BIOS Features
This setup page includes all the items of Award BIOS enhanced features.
Advanced Chipset Features
This setup page includes all the items of Chipset configuration features.
Integrated Peripherals
This setup page includes all onboard peripheral devices.
Security chip configuration
This SETUP page includes all the items of Trusted Module Configuration features. This sub-menu item only appears when Trusted Module plug in.
Power Management Setup
This setup page includes all the items of Power Management features.
PnP/PCI Configurations
This setup page includes PnP OS and PCI device configuration.
PC Health Status
This setup page includes the system auto detect CPU and system temperature,
voltage, fan speed.
Frequency/Voltage Control
This setup page includes CPU host clock control, frequency ratio and voltage.
Load Setup Defaults
This setup page includes Load system optimized value, and the system would
be in best performance configuration.
Set Password
Establish, change or disable password.
Save & Exit Setup
Save CMOS value settings to CMOS and exit BIOS setup.
Exit Without Saving
Abandon all CMOS value changes and exit BIOS setup.
33
AIMB-562 KIOSK User Manual
3.2.2 Standard CMOS Features

Date
The date format is <weekday>, <month>, <day>, <year>.
Weekday
From Sun to Sat, determined and displayed by BIOS only
Month
From Jan. to Dec.
Day
From 1 to 31
Year
From 1999 through 2098

Time
The time format is <hour> <minute> <second>, based on 24-hour time.
IDE Channel 0 Master/Slave
IDE HDD Auto-Detection Press "Enter" for automatic device detection.
Video
Select EGA or VGA display.
Halt on
The item determines whether the computer will stop if an error is detected during power up.
No Errors
The system boot will not stop for any error.
All Errors
Whenever the BIOS detects a non-fatal error the system will be
stopped.
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all
other errors. (Default value)

Base Memory
The POST of the BIOS will determine the amount of base (or conventional)
memory installed in the system.
Extended Memory
The BIOS POST will determine the amount of extended memory (above 1 MB
in CPU’s memory address map) installed in the system.
Total Memory
This item displays the total system memory size.
AIMB-562 KIOSK User Manual
34

CPU Feature
This item allows user to adjust CPU features.
Hard Disk Boot Priority
This item allows user to select boot sequence for system device HDD, USBHDD, SCSI, RAID.
Virus Warning[Disabled]
Enables or disables the virus warning.
CPU L3 Cache
This item allows user to enable CPU L3 cache.
Quick Power On Self Test[Enabled]
This field speeds up the Power-On Self Test (POST) routine by skipping retesting a second, third and forth time. Setup setting default is enabled.
First / Second / Third / Other Boot Drive
Hard Disk
Select boot device priority by Hard Disk.
CDROM
Select boot device priority by CDROM.
USB-FDD
Select boot device priority by USB-FDD.
USB-ZIP
Select boot device priority by USB-ZIP.
USB-CDROM
Select boot device priority by USB-CDROM.
LAN
Select boot device priority by LAN.
Disabled
Disable this boot function.
Gate A20 Option [Fast]
This item enables users to switch A20 control by port 92 or not.
Typematic Rate Setting
This item enables users to set the two typematic controls items.
– Typematic Rate (Chars/Sec)
This item controls the speed at which the system registers auto-repeated keystrokes. The eight settings are 6, 8, 10, 12, 15, 20, 24 and 30.
– Typematic Delay (Msec)
This item sets the keypress time delay before autorepeat begins.
Four delay rate options are 250, 500, 750 and 1000.
35
AIMB-562 KIOSK User Manual
BIOS Operation

Chapter 3
3.2.3 Advanced BIOS Features

Security Option [Setup]
System
System will not boot and refuses access to Setup page if the correct password is not entered at the prompt.
Setup
System will boot, but access to Setup requires password (default
value).
APIC Mode [Enabled]
This item allows user to enabled of disabled “Advanced Programmable Interrupt Controller”. APIC is implemented in the motherboard and must be supported by the operating system, and it extends the number of IRQ's available.
3.2.4 Advanced Chipset Features
Note!

This “Advanced Chipset Features” page controls configuration of the
board’s chipset. This page is chipset dependent; screens may differ
somewhat depending on the chipset. It is strongly recommended that
only technical users make changes to the default settings.
DRAM Timing Selectable [By SPD]
This item enables users to set the optimal timings for items 2 through 5; system
default setting “By SPD” follows the SPD information and ensures the system
runs stably with optimal performance.
CAS Latency Time [Auto]
This item enables users to set the timing delay in clock cycles before SDRAM
starts a read command after receiving it.
DRAM RAS# to CAS# Delay [Auto]
This item enables users to set the timing of the transition from RAS (row
address strobe) to CAS (column address strobe) as both rows and column are
separately addressed shortly after DRAM is refreshed.
DRAM RAS# Precharge [Auto]
This item enables users to set the DRAM RAS# precharge timing, system
default is setting to “Auto” to reference the data from SPD ROM.
Precharge delay (tRAS) [Auto]
This item allows user to adjust memory precharge time.
AIMB-562 KIOSK User Manual
36

37
AIMB-562 KIOSK User Manual
BIOS Operation

System Memory Frequency [Auto]
This item allows user to adjust memory frequency to improvement performance.
System BIOS Cacheable [Enabled]
This item allows the system BIOS to be cached to allow faster execution and
better performance.
Video BIOS Cacheable [Disabled]
This item allows the video BIOS to be cached to allow faster execution and better performance.
Memory Hole At 15 M-16 M [Disabled]
This item reserves 15 MB-16 MB memory address space to ISA expansion
cards that specifically require the setting. Memory from 15 MB-16 MB will be
unavailable to the system because of the expansion cards can only access
memory at this area.
PCI Express Root port Func [Press Enter]
This item allows the user to adjust PCIE port on, off or auto.
On-Chip Frame Buffer Size [8 MB]
This item allows the user to adjust the on-chip frame buffer size 8 MB or 1 MB.
DVMT Mode [DVMT]
This item allows the user to adjust Intel's Dynamic Video Memory Technology
(DVMT). BIOS provides three options: DVMT, FIXED, and Both.
DVMT/FIXED Memory Size [128MB]
This item allows the user to adjust DVMT/FIXED graphics memory size.
Init Display First
This item is the setting for start up video output: either from PCI Express or
Onboard device.
Chapter 3

3.2.5 Integrated Peripherals
Note!
This “Integrated Peripherals” page controls the configuration of the
board’s chipset, including IDE, ATA, SATA, USB, AC97, MC97 and
Super IO and Sensor devices. This page is chipset dependent; the
screen capture above is illustrative, but screens do differ depending on
chipset features.

OnChip IDE Device
This item enables users to set the OnChip IDE device status, including some of
new chipsets also support SATA devices (Serial-ATA).

Onboard Device
This item enables users to set the Onboard device status, including enabling
USB, AC97, and LAN devices.
AIMB-562 KIOSK User Manual
38
Chapter 3
Super IO Device
This item enables users to set the Super IO device status, including enabling of
COM, LPT, and IR.

Onboard Serial port 1 [3F8 / IRQ4]
This item allows user to adjust serial port 1 of address and IRQ.
Onboard Serial port 2 [ 2F8/ IRQ3]
This item allows user to adjust serial port 2 of address and IRQ.
UART Mode Select [Normal]
This item allows you to select UART mode. The choices: “IrDA”, “ASKIR”, and
“Normal”.
RxD, TxD Active
This item allows you to determine the active level of the RxD and TxD serial
lines. The choices: “Hi, Hi”, “Lo, Lo”, “Lo, H”, and “Hi, Lo”.
IR Transmission Delay
This item allows you to enable/disable IR transmission delay. The options are
“Enabled” and “Disabled”.

39
AIMB-562 KIOSK User Manual
BIOS Operation

UR2 Duplex Mode
This item allows you to select the IR half/full duplex function. The options are
“Half” and “Full”.
Use IR Pins
The options are “RxD2, TxD2” and “IR-Rx2Tx2”.
Onboard Parallel Port [378/IRQ7]
This item allows user to adjust parallel port of address and IRQ.
Parallel Port Mode [ECP+EPP]
This item allows user to adjust parallel port mode.
EPP Mode Select [EPP1.9]
This field allows you to select EPP port type 1.7 or 1.9. The choices are
“EPP1.9” and “EPP1.7”.
ECP Mode Use DMA [3]
This item allows user to adjust ECP DMA resource.
Onboard Serial port 3 [3E8/IRQ10]
This item allows user to adjust serial port 3 of address and IRQ.
Onboard Serial port 4 [2E8/IRQ10]
This item allows user to adjust serial port 4 of address and IRQ.
3.2.6 Security Chip Configuration
3.2.7 TPM Support
The items in this menu allow you to set the TPM (Trusted Platform Module) features.
Select an item and then press <Enabled> to display the configuration options.
Note!
To enable the TPM function, set the TPM Support item to [Enabled] and
then save the change; after rebooting, the TPM configuration menu will
show the active options.
AIMB-562 KIOSK User Manual
40

Adjust “Power management Setup” to configure the system to most
effective energy savings still consistent with the intended style of use.
PCI Express PM Function
This allows you to control Power On by onboard LAN chip feature.
Power-Supply Type [ATX]
This item allows user to set power-supply type, ATX or AT mode.
ACPI Function [Enabled]
This item defines the ACPI (Advanced Configuration and Power Management)
feature that makes hardware status information available to the operating system, and communicates with PC and system devices for improving the power
management.
ACPI Suspend Type [S3(STR)]
This item allows user to select sleep state when in suspend.
S1(POS)
The suspend mode is equivalent to a software power down;
S3(STR)
The system shuts down with the exception of a refresh current to
the system memory.
Run VGA BIOS if S3 Resume [Auto]
This item allows system to reinitialize VGA BIOS after system resume from
ACPI S3 mode.
Power Management [User Define]
This item allows user to select system power saving mode.
Min Saving
Minimum power management. Suspend Mode=1 hr.
Max Saving
Maximum power management. Suspend Mode=1 min.
User Define
Allows user to set each mode individually. Suspend Mode= Disabled or 1 min ~1 hr.
41
AIMB-562 KIOSK User Manual
BIOS Operation
Note!
Chapter 3
3.2.8 Power Management Setup

Video Off Method [DPMS]
This item allows user to determine the manner is which the monitor is blanked.
V/H SYNC+Blank This option will cause system to turn off vertical and horizontal synchronization ports and write blanks to the video buffer.

Blank Screen
This option only writes blanks to the video buffer.
DPMS
Initial display power management signaling.
Video Off In Suspend [Yes]
This item allows user to turn off video when system is in suspend mode.
Suspend Type [Stop Grant]
This item allows user to determine the suspend type.
Modem use IRQ [3]
This item allows user to determine which IRQ the MODEM can use.
Suspend Mode [Disabled]
This item allows user to set a delay time. If system inactivity exceeds the delay
time, all devices except the CPU will be shut off.
Soft-Off by PWR-BTTN [Instant-Off]
This item allows user to define function of power button.
Instant-Off
Pressing power button initiates instant power off.
Delay 4 Sec
Press power button for four seconds to initiate power off.
PowerOn by LAN [Enabled]
This item allows user to power on the system via LAN. The choices are
“Enabled” and “Disabled”.
PowerOn by Modem [Enabled]
This item allows user to power on the system by Modem. The choices are
“Enabled” and “Disabled”.
USB KB Wake_Up From S3 [Disabled]
This item allows user to allow a USB keyboard to wake up the system from S3
suspend. Options: Enabled or Disabled.
PowerOn by Alarm [Disabled]
The choices are “Enabled” and “Disabled”. If enabled, the fields that follow indicate dates and times of alarm settings.
Primary IDE 0 (1) and Secondary IDE 0 (1) [Disabled]
When Enabled, the system will resume from suspend mode if Primary IDE 0 (1)
or Secondary IDE 0 (1) becomes active. The choices are “Enabled” and “Disabled”.
FDD, COM, LPT PORT [Disabled]
When Enabled, the system will resume from suspend mode if the FDD interface, COM port, or LPT port becomes active. The choices are ”Enabled” and
“Disabled”.
PCI PIRQ [A-D]# [Disabled]
When Enabled, the system resumes from suspend mode if an interrupt occurs.
The choices are “Enabled” and “Disabled”.
PWRON After PWR-Fail [Former-Sts]
Use this to set up the system after power failure. The “Off” setting keeps the
system powered off after power failure, the “On” setting boots up the system
after failure, and the “Former-Sts” returns the system to the status before power
failure.
AIMB-562 KIOSK User Manual
42

Reset Configuration Data [Disabled]
The default is Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) if you have installed a new add-on card, and system configuration is in such a state that the OS cannot boot.
Resources Controlled By [Auto(ESCD)]
The commands here are “Auto(ESCD)” or “Manual”. Choosing “Manual”
requires you to choose resources from the following sub-menu. “Auto(ESCD)”
automatically configures all of the boot and Plug and Play devices, but you
must be using Windows 95 or above.
PCI / VGA Palette Snoop [Disabled]
This is set to “Disabled” by default.
Maximum Payload Size [128]
This item shows you the maximum TLP payload size for PCI Express devices.
The option is set to [128 bytes] by chipset specification.
43
AIMB-562 KIOSK User Manual
BIOS Operation

Chapter 3
3.2.9 PnP/PCI Configurations
3.2.10 PC Health Status

ACPI Shutdown Temperature [Disabled]
The system will shut down automatically if the CPU temperature goes over the
selected setting.
CPU Warning Temperature [Disabled]
The system will give an automatic warning if the CPU temperature goes over
the selected setting.
Current System Temperature
This shows you the current temperature of system.
Current CPU Temperature
This shows the current CPU temperature.
VCORE and Other Voltages
This shows the voltage of VCORE, +3.3 V, +5 V, +12 V, -12 V, VBAT(V), and 5
VSB (V).
AIMB-562 KIOSK User Manual
44
Load Setup Defaults loads the default system values directly from ROM.
Useful if the stored record created by the Setup program should ever
become corrupted (and therefore unusable).
3.2.12 Set Password
Note!
To enable this feature, you should first go to the Advanced BIOS Features menu, choose the Security Option, and select either Setup or System, depending on which aspect you want password protected. “Setup”
requires a password only to enter Setup. “System” requires the password either to enter Setup or to boot the system. A password can be at
most 8 characters long.
45
AIMB-562 KIOSK User Manual
BIOS Operation
Note!
Chapter 3
3.2.11 Load Setup Defaults
To Establish Password
1. Choose the Set Password option from the CMOS Setup Utility main menu and
press <Enter>.
2. When you see “Enter Password”, enter the desired password and press
<Enter>.
3. At the “Confirm Password” prompt, retype the desired password, then press
<Enter>.
4. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
To Change Password
1. Choose the Set Password option from the CMOS Setup Utility main menu and
press <Enter>.
2. When you see “Enter Password”, enter the existing password and press
<Enter>.
3. You will see “Confirm Password”. Type it again, and press <Enter>.
4. Select Set Password again, and at the “Enter Password” prompt, enter the new
password and press <Enter>.
5. At the “Confirm Password” prompt, retype the new password, and press
<Enter>.
6. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
To Disable Password
1. Choose the Set Password option from the CMOS Setup Utility main menu and
press <Enter>.
2. When you see “Enter Password”, enter the existing password and press
<Enter>.
3. You will see “Confirm Password”. Type it again, and press <Enter>.
4. Select Set Password again, and at the “Enter Password” prompt, please don’t
enter anything; just press <Enter>.
5. At the”Confirm Password” prompt, again, don’t type in anything; just press
<Enter>.
6. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
AIMB-562 KIOSK User Manual
46
Typing “Y” will quit the BIOS Setup Utility and save user setup values to
CMOS.
Typing “N” will return to BIOS Setup Utility.
3.2.14 Quit without Saving
Note!
Typing “Y” will quit the BIOS Setup Utility without saving to CMOS.
Typing “N” will return to BIOS Setup Utility.
47
AIMB-562 KIOSK User Manual
BIOS Operation
Note!
Chapter 3
3.2.13 Save & Exit Setup
AIMB-562 KIOSK User Manual
48
Chapter
4
Chipset Software
Installation Utility
4
4.1 Before you begin
To facilitate the installation of the enhanced display drivers and utility software, read
the instructions in this chapter carefully. The drivers for the AIMB-562 KIOSK are
located on the software installation CD. The driver in the folder of the driver CD will
guide and link you to the utilities and drivers under a Windows system. Updates are
provided via Service Packs from Microsoft*.
Note!
The files on the software installation CD are compressed. Do not
attempt to install the drivers by copying the files manually. You must use
the supplied SETUP program to install the drivers.
Before you begin, it is important to note that most display drivers need to have the
relevant software application already installed in the system prior to installing the
enhanced display drivers. In addition, many of the installation procedures assume
that you are familiar with both the relevant software applications and operating system commands. Review the relevant operating system commands and the pertinent
sections of your application software’s user manual before performing the installation.
4.2 Introduction
The Intel® Chipset Software Installation (CSI) utility installs the Windows INF files
that outline to the operating system how the chipset components will be configured.
This is needed for the proper functioning of the following features:
Core PCI PnP services
IDE Ultra ATA 100/66/33 and Serial ATA interface support
USB 1.1/2.0 support (USB 2.0 driver needs to be installed separately for Win98)

Identification of Intel® chipset components in the Device Manager
Integrates superior video features. These include filtered sealing of 720 pixel
DVD content, and MPEG-2 motion compensation for software DVD
Note!
This utility is used for the following versions of Windows, and it has to be
installed before installing all the other drivers:
Windows 2000
Windows XP
Windows Vista
AIMB-562 KIOSK User Manual
50
1.
Insert the driver CD into your system's CD-ROM drive. You can see the driver
folder items. Navigate to the "INF" folder and click "setup.exe" to complete the
installation of the driver.
Chapter 4
4.3 Windows XP Driver Setup
Chipset Software Installation Utility
51
AIMB-562 KIOSK User Manual
AIMB-562 KIOSK User Manual
52
Chapter
5
VGA Setup
5
5.1 Introduction
The Intel 945G/945GC integrated graphics controller. You need to install the VGA
driver to enable the function.
The Intel 945G/945GC integrated graphics controller includes the following features:
Intel Graphics Media Accelerator 950: Incorporating the latest Microsoft*
DirectX*9 support capabilities, it allows software developers to create lifelike
environments and characters. Dual independent display, enhanced display
modes for widescreen flat panels, and optimized 3D support deliver an intense
and realistic visual experience without requiring a separate graphics card.
5.2 Windows Vista/XP/2000
Note!
Before installing this driver, make sure the CSI utility has been installed
in your system. See Chapter 4 for information on installing the CSI utility.
Insert the driver CD into your system's CD-ROM drive. You can see the driver folders
items. Navigate to the "VGA" folder and click "setup.exe" to complete the installation
of the drivers for Vista, Windows XP, and Windows 2000.
AIMB-562 KIOSK User Manual
54
Chapter 5
VGA Setup
55
AIMB-562 KIOSK User Manual
AIMB-562 KIOSK User Manual
56
Chapter
6
6
LAN Configuration
6.1 Introduction
The AIMB-562 KIOSK has a single/dual Gigabit Ethernet LAN via dedicated PCI
Express x 1 bus (Realtek RTL8111C), which offers bandwidth of up to 500 MB/sec,
eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet to
operate at 1000 Mbps.
6.2 Features

Integrated 10/100/100 BASE-T transceiver
10/100/1000 BASE-T triple-speed MAC
High-speed RISC core with 24-KB cache
On-chip voltage regulation
Wake-on-LAN (WOL) support
PCI Express X1 host interface
6.3 Installation
Note!
Before installing the LAN drivers, make sure the CSI utility has been
installed on your system. See Chapter 4 for information on installing the
CSI utility.
The AIMB-562 KIOSK Realtek RTL8111C Gigabit integrated controller supports all
major network operating systems. However, the installation procedure varies with different operating systems. Please find and use the section that provides the driver
setup procedure for the operating system you are using.
6.4 Win XP/Vista Driver Setup (Realtek RTL8111C)
Insert the driver CD into your system's CD-ROM drive. Select the Drv_LAN folder
then navigate to the directory for your OS.
AIMB-562 KIOSK User Manual
58
Chapter 6
LAN Configuration
59
AIMB-562 KIOSK User Manual
AIMB-562 KIOSK User Manual
60
Appendix
A
A
Programming the
Watchdog Timer
A.1 Programming the Watchdog Timer
The AIMB-562 KIOSK's watchdog timer can be used to monitor system software
operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how
to program it.
A.1.1 Watchdog timer overview
The watchdog timer is built into the super I/O controller W83627DHG. It provides the
following user-programmable functions:
Can be enabled and disabled by user program
Timer can be set from 1 to 255 seconds or 1 to 255 minutes
Generates an interrupt or resets signal if the software fails to reset the timer
before time-out
A.1.2 Programming the Watchdog Timer
The I/O port address of the watchdog timer is 2E (hex) and 2F (hex). 2E (hex) is the
address port. 2F (hex) is the data port. You must first assign the address of register
by writing an address value into address port 2E (hex), then write/read data to/from
the assigned register through data port 2F (hex).
AIMB-562 KIOSK User Manual
62
Appendix A Programming the Watchdog Timer
Unlock W83627DHG
Select register of
watchdog timer
Enable the function of
the watchdog timer
Use the function of
the watchdog timer
Lock W83627DHG
63
AIMB-562 KIOSK User Manual
Table A.1: Watchdog Timer Registers
Address of register (2E) Attribute
Read/Write
Value (2F) &
description
87 (hex)
-----
Write this address to I/O address port 2E (hex)
twice to unlock the W83627DHG.
07 (hex)
write
Write 08 (hex) to select register of watchdog timer.
30 (hex)
write
Write 01 (hex) to enable the function of the watchdog timer. Disabled is set as default.
write
Set seconds or minutes as units for the timer.
Write 0 to bit 3: set second as counting unit.
[default]
Write 1 to bit 3: set minutes as counting unit.
write
0: stop timer [default]
01~FF (hex): The amount of the count, in seconds
or minutes, depends on the value set in register F5
(hex). This number decides how long the watchdog
timer waits for strobe before generating an interrupt or reset signal. Writing a new value to this register can reset the timer to count with the new
value.
F7 (hex)
read/write
Bit 7:Write 1 to enable mouse to reset the timer, 0
to disable[default]. Bit 6: Write 1 to enable keyboard to reset the timer, 0 to disable.[default]
Bit 5: Write 1 to generate a timeout signal immediately and automatically return to 0. [default=0]
Bit 4: Read status of watchdog timer, 1 means
timer is “timeout”.
AA (hex)
-----
Write this address to I/O port 2E (hex) to lock the
watchdog timer 2.
F5 (hex)
F6 (hex)
AIMB-562 KIOSK User Manual
64
1. Enable watchdog timer and set 10 sec. as timeout interval
;----------------------------------------------------------Mov dx,2eh ; Unlock W83627DHG
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------Mov al,07h ; Select registers of watchdog timer
Out dx,al
Inc dx
Mov al,08h
Out dx,al
;----------------------------------------------------------Dec dx ; Enable the function of watchdog timer
Mov al,30h
Out dx,al
Inc dx
Mov al,01h
Out dx,al
;----------------------------------------------------------Dec dx ; Set second as counting unit
Mov al,0f5h
Out dx,al
Inc dx
In al,dx
And al,not 08h
Out dx,al
;----------------------------------------------------------Dec dx ; Set timeout interval as 10 seconds and start counting
Mov al,0f6h
Out dx,al
Inc dx
Mov al,10
Out dx,al
;----------------------------------------------------------Dec dx ; Lock W83627HG
Mov al,0aah
Out dx,al
2. Enable watchdog timer and set 5 minutes as timeout interval
;----------------------------------------------------------Mov dx,2eh ; Unlock W83627HG
Mov al,87h
Out dx,al
Out dx,al
65
AIMB-562 KIOSK User Manual
Appendix A Programming the Watchdog Timer
A.1.3 Example Program
;----------------------------------------------------------Mov al,07h ; Select registers of watchdog timer
Out dx,al
Inc dx
Mov al,08h
Out dx,al
;----------------------------------------------------------Dec dx ; Enable the function of watchdog timer
Mov al,30h
Out dx,al
Inc dx
Mov al,01h
Out dx,al
;----------------------------------------------------------Dec dx ; Set minute as counting unit
Mov al,0f5h
Out dx,al
Inc dx
In al,dx
Or al,08h
Out dx,al
;----------------------------------------------------------Dec dx ; Set timeout interval as 5 minutes and start counting
Mov al,0f6h
Out dx,al
Inc dx
Mov al,5
Out dx,al
;----------------------------------------------------------Dec dx ; Lock W83627HG
Mov al,0aah
Out dx,al
3. Enable watchdog timer to be reset by mouse
;----------------------------------------------------------Mov dx,2eh ; Unlock W83627HG
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------Mov al,07h ; Select registers of watchdog timer
Out dx,al
Inc dx
Mov al,08h
Out dx,al
;-----------------------------------------------------------
AIMB-562 KIOSK User Manual
66
67
AIMB-562 KIOSK User Manual
Appendix A Programming the Watchdog Timer
Dec dx ; Enable the function of watchdog timer
Mov al,30h
Out dx,al
Inc dx
Mov al,01h
Out dx,al
;----------------------------------------------------------Dec dx ; Enable watchdog timer to be reset by mouse
Mov al,0f7h
Out dx,al
Inc dx
In al,dx
Or al,80h
Out dx,al
;----------------------------------------------------------Dec dx ; Lock W83627HG
Mov al,0aah
Out dx,al
4. Enable watchdog timer to be reset by keyboard
;----------------------------------------------------------Mov dx,2eh ; Unlock W83627HG
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------Mov al,07h ; Select registers of watchdog timer
Out dx,al
Inc dx
Mov al,08h
Out dx,al
;----------------------------------------------------------Dec dx ; Enable the function of watchdog timer
Mov al,30h
Out dx,al
Inc dx
Mov al,01h
Out dx,al
;----------------------------------------------------------Dec dx ; Enable watchdog timer to be strobed reset by keyboard
Mov al,0f7h
Out dx,al
Inc dx
In al,dx
Or al,40h
Out dx,al
;----------------------------------------------------------Dec dx ; Lock W83627HG
Mov al,0aah
Out dx,al
5. Generate a time-out signal without timer counting
;----------------------------------------------------------Mov dx,2eh ; Unlock W83627HG
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------Mov al,07h ; Select registers of watchdog timer
Out dx,al
Inc dx
Mov al,08h
Out dx,al
;----------------------------------------------------------Dec dx ; Enable the function of watchdog timer
Mov al,30h
Out dx,al
Inc dx
Mov al,01h
Out dx,al
;----------------------------------------------------------Dec dx ; Generate a time-out signal
Mov al,0f7h
Out dx,al ;Write 1 to bit 5 of F7 register
Inc dx
In al,dx
Or al,20h
Out dx,al
;----------------------------------------------------------Dec dx ; Lock W83627HG
Mov al,0aah
Out dx,al
AIMB-562 KIOSK User Manual
68
Appendix
B
B
I/O Pin Assignments
B.1 Parallel Port (LPT1)
Table B.1: Parallel Port (LPT1)
Pin
Signal
Pin
Signal
1
STROBE*
14
AUTOFD*
2
D0
15
ERR
3
D1
16
INIT*
4
D2
17
SLCTINI*
5
D3
18
GND
6
D4
19
GND
7
D5
20
GND
8
D6
21
GND
9
D7
22
GND
10
ACK*
23
GND
11
BUSY
24
GND
12
PE
25
GND
13
SLCT
26
N/C
* Low activity
B.2 USB Header (USB56)
Table B.2: USB Header (USB56)
Pin
Signal
Pin
Signal
1
USB0_VCC5
2
USB1_VCC5
3
USB0_D-
4
USB1_D-
5
USB0_D+
6
USB1_D+
7
GND
8
GND
9
Key
10
GND
AIMB-562 KIOSK User Manual
70
Table B.3: USB Header (USB78)
Pin
Signal
Pin
Signal
1
USB0_VCC5
2
USB1_VCC5
3
USB0_D-
4
USB1_D-
5
USB0_D+
6
USB1_D+
7
GND
8
GND
9
Key
10
GND
B.4 VGA Connector (VGA1)
Table B.4: VGA Connector (VGA1)
Pin
Signal
Pin
Signal
1
RED
9
CRT_VCCIN
2
VGA_G
10
GND
3
VGA_B
11
N/C
4
N/C
12
V_SDAT
5
GND
13
H-SYNC
6
GND
14
V-SYNC
7
GND
15
V_SCLK
8
GND
71
AIMB-562 KIOSK User Manual
Appendix B I/O Pin Assignments
B.3 USB Header (USB78)
B.5 VGA Connector (VGA2)
Table B.5: VGA Connector (VGA2)
Pin
Signal
Pin
Signal
1
RED
9
CRT_VCCIN
2
VGA_G
10
GND
3
VGA_B
11
N/C
4
N/C
12
V_SDAT
5
GND
13
H-SYNC
6
GND
14
V-SYNC
7
GND
15
V_SCLK
8
GND
B.6 RS-232 Interface (COM1-COM2)
7 5 3
1
10 8 6 4
2
9
Table B.6: RS-232 Interface (COM1~COM2)
Pin
Signal
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RRI
9
GND
AIMB-562 KIOSK User Manual
72
Table B.7: RS-232/422/485 Setting Interface (JETCOM3456~78910)
Pin
Signal
Pin
Signal
1
R_SINA
2
RXD485_1
3
R_SINA
4
RXD422_1
5
R_SINA
6
RXD232_1
7
DCDA
8
SOUTA
9
COM1_DCD#
10
COM1_SOUT
11
COM1_TXD485N
12
COM1_RXD485P
13
SINA
14
DTRA
15
COM1_SIN
16
COM1_DTR#
17
COM1_TXD485P
18
COM1_RXD485N
B.8 RS-232 Interface (COM3456)
Table B.8: RS-232 Interface(3456)
Pin
Signal
Pin
Signal
1
COM3_1
2
DDSR3#
3
COM3_2
4
RRTS3#
5
COM3_3
6
CCTS3#
7
COM3_4
8
RRI3#
9
GND
10
GND
11
DDCD4#
12
DDSR4#
13
RRXD4
14
RRTS4#
15
TTXD4
16
CCTS4#
17
DDTR4#
18
RR14#
19
GND
20
GND
21
DDCD5#
22
DDSR5#
23
RRXD5
24
RRTS5#
25
TTXD5
26
CCTS5#
27
DDTR5#
28
RRI5#
29
GND
30
GND
31
DDCD5#
32
DDSR6#
33
RRXD6
34
RRTS6#
35
TTXD6
36
CCTS6#
37
DDTR6#
38
RRI6#
39
GND
40
GND
COM3 is RS-232/422/485.
73
AIMB-562 KIOSK User Manual
Appendix B I/O Pin Assignments
B.7 RS-232/422/485 Setting Interface
(JETCOM3456~78910)
B.9 RS-232 Interface (COM78910)
Table B.9: RS-232 Interface (COM78910)
Pin
Signal
Pin
Signal
1
COM7_1
2
DDSR7#
3
COM7_2
4
RRTS7#
5
COM7_3
6
CCTS7#
7
COM7_4
8
RRI7#
9
GND
10
GND
11
DDCD8#
12
DDSR8#
13
RRXD8
14
RRTS8#
15
TTXD8
16
CCTS8#
17
DDTR8#
18
RR18#
19
GND
20
GND
21
DDCD9#
22
DDSR9#
23
RRXD9
24
RRTS9#
25
TTXD9
26
CCTS9#
27
DDTR9#
28
RRI9#
29
GND
30
GND
31
DDCD9#
32
DDSR10#
33
RRXD10
34
RRTS10#
35
TTXD10
36
CCTS10#
37
DDTR10#
38
RRI10#
39
GND
40
GND
COM7 is RS-232/422/485.
AIMB-562 KIOSK User Manual
74
1
2
7
8
Table B.10: SPI_CN1:SPI fresh card pin connector
Pin
Signal
Pin
Signal
1
+F1_3V
2
GND
3
F1_SPI_CS#_Q
4
F1_SPI_CLK_Q
5
F1_SPI_MISO_Q
6
F1_SPI_MOSI_Q
7
NC
8
NC
B.11 PS/2 Keyboard and Mouse Connector (KBMS1)
Table B.11: PS/2 Keyboard and Mouse Connector (KBMS1)
Pin
Signal
1
KB DATA
2
N/C
3
GND
4
KB VCC
5
KB CLK
6
N/C
7
M_DATA
8
N/C
9
GND
10
M_VCC
11
M_CLK
12
N/C
75
AIMB-562 KIOSK User Manual
Appendix B I/O Pin Assignments
B.10 SPI_CN1: SPI fresh card pin connector
B.12 CPU Fan Power Connector (CPU_FAN1)
1
Table B.12: CPU Fan Power Connector (CPU_FAN1)
Pin
Signal
1
GND
2
+12 V
3
DETECT
4
PWM
B.13 System Fan Power Connector (SYS_FAN1/
SYS_FAN2)
1
2
3
Table B.13: System Fan Power Connector (SYSFAN1/SYSFAN2)
Pin
Signal
1
GND
2
+12 V
3
DETECT
B.14 Front Panel Connectors (JFP1)
1
AIMB-562 KIOSK User Manual
2
76
2
Appendix B I/O Pin Assignments
B.14.1Power/Sleep LED (JFP1)
4
Table B.14: Power/Sleep LED (JFP1)
Pin
Signal
2
LED power (+5 V)
4
LED power (+5 V)
B.14.2Reset Connector (JFP1)
5
7
Table B.15: Reset Connector (JFP1)
Pin
Signal
5
RESET
7
GND
12
B.14.3HDD LED Connector (JFP1)
1
3
Table B.16: HDD LED Connector (JFP1)
Pin
Signal
1
IDE LED+
3
IDE LED-
B.14.4ATX Soft Power Switch (JFP1)
6
8
Table B.17: ATX Soft Power Switch (JFP1)
Pin
Signal
6
5 VSB
8
PWR-BTN
77
AIMB-562 KIOSK User Manual
B.15 ATX1 12 V Auxiliary Power Connector
(ATX12V1)
Table B.18: ATX1 12 V Auxiliary Power Connector (ATX12V1)
Pin
Signal
1
GND
2
GND
3
+12 V
4
+12 V
B.16 ATX Power Connector (EATXPWR1)
Table B.19: ATX Power Connector (ATX2)
Pin
Signal
Pin
Signal
1
+3.3 V
2
+3.3 V
3
GND
4
+5 V
5
GND
6
+5 V
7
GND
8
POK
9
5 VSB
10
12 V
11
12 V
12
3.3 V
13
3.3 V
14
-12 V
15
GND
16
PSON
17
GND
18
GND
19
GND
20
-5 V
AIMB-562 KIOSK User Manual
78
12
34
12
34
Table B.20: USB Port
Pin
Signal
Pin
Signal
1
VCC
3
Data0+
2
Data0-
4
GND
Table B.21: Ethernet 10/100Base-T RJ-45 Port
Pin
Signal
Pin
Signal
1
XMT+
5
N/C
2
XMT-
6
RCV-
3
RCV+
7
N/C
4
N/C
8
N/C
B.18 Line Out, Mic In Connector (AUDIO1)
Line Out
Mic In
B.19 Serial ATA0 (SATA1)
Table B.22: Serial ATA0 (SATA1)
Pin
Signal
Pin
Signal
1
GND
2
SATA_0TX+
3
SATA_0TX-
4
GND
5
SATA_0RX-
6
SATA_0RX+
7
GND
8
79
AIMB-562 KIOSK User Manual
Appendix B I/O Pin Assignments
B.17 USB/LAN ports (LAN2_USB12/USB34)
B.20 Serial ATA1 (SATA2)
Table B.23: Serial ATA1 (SATA2)
Pin
Signal
Pin
Signal
1
GND
2
SATA_1TX+
3
SATA_1TX-
4
GND
5
SATA_1RX-
6
SATA_1RX+
7
GND
8
B.21 AT/ATX Mode (PSON1)
Table B.24: AT/ATX Mode (PSON1)
Pin
Signal
Pin
Signal
1
#PSON_SIO
(to super IO)
2
#PSON
(to power supply)
3
GND
B.22 JLVDS1: LVDS connector
Table B.25: LVDS Connector (JLVDS1)
Pin
Signal
Pin
Signal
1
VDDSAFE
2
VDDSAFE
3
GND
4
GND
5
VDDSAFE
6
VDDSAFE
7
OD0-
8
ED0-
9
OD0+
10
ED0+
11
GND
12
GND
13
OD1-
14
ED1-
15
OD1+
16
ED1+
17
GND
18
GND
19
OD2-
20
ED2-
21
OD2+
22
ED2+
23
GND
24
GND
25
OCK-
26
ECK-
27
OCK+
28
ECK+
29
GND
30
GND
31
DDC_CLK
32
DDC DAT
33
GND
34
GND
35
OD3-
36
ED3-
37
OD3+
38
ED3+
39
HPLG
40
VCON
AIMB-562 KIOSK User Manual
80
Table B.26: LCD Inverter Power Connector (JBL1)
Pin
Signal
1
VCC12_INV1
2
GND
3
LVDS_BKLTEN
4
VBR
5
VP3_P5
B.24 JLVDSPWR1(LVDS power jumper selection)
Table B.27: LVDS power jumper selection (JLVDSPWR1)
Pin
Signal
1
3.3 V
2
+LVDS_PWR_SEL
3
5V
1-2 pin
2-3 pin
3.3 V
5V
B.25 FPAUDIO1(Front Panel Audio Connector)
Table B.28: Front Panel Audio Connector (FPAUDIO1)
Pin
Signal
1
MIC2_L
2
AGND
3
MIC2_R
4
PRESENSE
5
LIN2_R
6
GND
7
FIO_JD
8
N/A
9
LIN2_L
10
GND
81
AIMB-562 KIOSK User Manual
Appendix B I/O Pin Assignments
B.23 JBL1(LVDS inverter connector)
B.26 GPIO12(GPIO pin header)
Table B.29: GPIO pin header(GPIO1)
Pin
Signal
Pin
Signal
1
DIO_GP20
5
DIO_GP22
2
DIO_GP24
6
DIO_GP26
3
DIO_GP21
7
DIO_GP23
4
DIO_GP25
8
DIO_GP27
Table B.30: GPIO pin header(GPIO2)
Pin
Signal
Pin
Signal
1
DIO_GP10
5
DIO_GP12
2
DIO_GP14
6
DIO_GP16
3
DIO_GP11
7
DIO_GP13
4
DIO_GP15
8
DIO_GP17
GPIO1 Pin 1 ~ Pin 8 current: GPI: 5V 1uA. GPO: 5 V 8 ~ 10 uA.
GPIO2 Pin 1, 3, 5, 7 current: GPO (output current only): 5 V, 200 mA
Pin 2, 4, 6, 8 current: GPI 5 V, 1 uA. GPO:5 V, 8~ 10 uA
GPIO2 Pin 1, 3, 5, 7 are for 200mAT high current output use only.
B.27 VOLADJ1(Volumn Adjustment connector)
Table B.31: Volumn Adjustment connector (VOLADJ1)
Pin
Signal
1
AMP_L_OUT_C
2
AMP_L_OUT
3
GND
4
AMP_R_OUT
5
AMP_R_OUT_C
B.28 System I/O Ports
Table B.32: System I/O Ports
Addr. range (Hex)
Device
000-01F
Interrupt controller 1, master
022-023
Chipset address
040-05F
8254 timer
060-06F
8042 (keyboard controller)
070-07F
Real-time clock, non-maskable interrupt (NMI) mask
080-09F
DMA page register
0A0-0BF
Interrupt controller 2
AIMB-562 KIOSK User Manual
82
0C0-0DF
DMA controller
0F0
Clear math co-processor
0F1
Reset math co-processor
0F8-0FF
Math co-processor
1F0-1F8
Fixed disk
200-207
Game I/O
278-27F
Parallel printer port 2 (LPT3)
290-297
On-board hardware monitor
2F8-2FF
Serial port 2
Serial port 2
Prototype card
360-36F
Reserved
378-37F
Parallel printer port 1 (LPT2)
380-38F
SDLC, bisynchronous 2
3A0-3AF
Bisynchronous 1
3B0-3BF
Monochrome display and printer adapter (LPT1)
3C0-3CF
Reserved
3D0-3DF
Color/graphics monitor adapter
3F0-3F7
Diskette controller
3F8-3FF
Serial port 1
B.29 JCASE1(Open Case Connector)
Table B.33: Case Open Connector(JCASE1)
Pin
Signal
1
+5VSB
2
N/A
3
ICH_INTRUDER#
4
GND
B.30 DMA Channel Assignments
Table B.34: DMA Channel Assignments
Channel
Function
0
Available
1
Available
2
Floppy disk (8-bit transfer)
3
Available
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
83
AIMB-562 KIOSK User Manual
Appendix B I/O Pin Assignments
Table B.32: System I/O Ports
B.31 Interrupt Assignments
Table B.35: Interrupt Assignments
Priority
Interrupt#
Interrupt source
1
NMI
Parity error detected
2
IRQ0
Interval timer
3
IRQ1
Keyboard
-
IRQ2
Interrupt from controller 2 (cascade)
4
IRQ8
Real-time clock
5
IRQ9
Cascaded to INT 0A (IRQ 2)
6
IRQ10
Serial communication port 3/4
7
IRQ11
Available
8
IRQ12
PS/2 mouse
9
IRQ13
INT from co-processor
10
IRQ14
Primary IDE Channel
11
IRQ15
Secondary IDE Channel
12
IRQ3
Serial communication port 2
13
IRQ4
Serial communication port 1
14
IRQ5
Available
15
IRQ6
Diskette controller (FDC)
16
IRQ7
Parallel port 1 (print port)
B.32 1st MB Memory Map
Table B.36: 1st MB Memory Map
Addr. range (Hex)
Device
E0000h - FFFFFh
BIOS
CC000h - DFFFFh
Unused
C0000h - CBFFFh
VGA BIOS
A0000h - BFFFFh
Video Memory
00000h - 9FFFFh
Base memory
AIMB-562 KIOSK User Manual
84
Appendix B I/O Pin Assignments
AIMB-562 KIOSK User Manual
85
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2009

Open as PDF

Similar pages: ARK-3381 User Manual; PCA-6780 User Manual; Primary - Advantech; ARK-5280 User Manual; ARK-3384 User Manual; PCI-6880 User`s Manual; USER`S MANUAL; PCM-9375 User Manual; PCM-9380 User Manual; 752.3KB - Axiomtek; User Manual AIMB-215; User Manual AIMB-252 (910GMLE/915GME); ADVANTECH DVMB-764; ADVANTECH SYS-4U4000-4S02; PCA-6010 PICMG 1.0 Full-sized Intel® LGA775 Processor Card with; ADVANTECH PCE; ADVANTECH PCE-3026G2; ETC LT133X1-104; Primary; User Manual; User's Manual; User Manual IPPC