ASMB-820I Intel® Xeon® E5-2400 series LGA 1356 Socket ATX

ASMB-820I Intel® Xeon® E5-2400 series LGA 1356 Socket ATX
Server Board with 4 PCIe & 2 PCI Expansion Slots
Startup Manual
Specifications
Packing List
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 ASMB-820I Startup Manual
• 1 Driver CD (user’s manual is included)
• 2 Serial ATA HDD data cables
• 2 Serial ATA HDD power cables
• 1 I/O port bracket
• 1 Warranty card
If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF
file.Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
Standard SBC Functions
• CPU: LGA1356 Intel ® Xeon® E5-2400 series
• BIOS: AMI 64 Mb SPI BIOS
• Chipset: Intel® C602J
• System memory: 6* DDR3 REG/ECC/Non-ECC
1066/1333/1600 unbuffered DIMM, Max. 96 GB
Note:
Due to the inherent limitations of PC architecture,
the system may not fully detect 96 GB RAM
when 96 GB RAM is installed.
• SATA Interface: 4 SATA2 3 Gb/s ports, 2 SATA3 6Gb/s,
supports Intel Matrix Storage (for Windows only) software
RAID 0, 1, 10 & 5.
• Serial ports: Two serial ports, only support RS-232
• Keyboard/mouse connector: Supports standard PS/2
keyboard and mouse
• Watchdog timer: 255 level timer intervals
• USB 2.0: Supports up to eleven USB 2.0 ports (2* TypeA)
VGA Interface
• Chipset: Aspeed AST2300
• Display Memory: 64 MB
• Resolution: Supports VGA up to resolution 1920 x 1200
@ 60 Hz refresh rate
Ethernet interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1:Intel 82579LM; LAN2: Intel 82574L;
LAN3: Realtek 8201EL(10/100Mbps for IPMI,ASMB-820I
sku only)
Mechanical and Environmental
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
• Dmensions (L x W): 304 x 244 mm (12” x 9.6”)
• Power supply voltage: +3.3 V, +5 V, ±12 V, +5 Vsb
• Power consumption(Main board only, excluded IO
device): Max. load: +3.3 V @ 24.75 A, +5 [email protected] 16.77 A,
+12 V @ 13.06 A, +12 V(8P) @ 22 A, +5 [email protected] 2 A
• Operating temperature: 0 ~ 60° C (depending on CPU)
• Weight: 1 kg (weight of board)
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the ASMB-820I series Rev. A1
Part No. 2006820I10
Print in China
1st Edition,
Feb. 2012
ASMB-820I Startup Manual 1
Jumpers and Connectors
Jumpers and Connectors
The board has a number of jumpers that allow you to configure your system to suit your application. The table below
lists the function of each jumper and connector.
JCMOS1/JME1: CMOS clear/ME update function
Result
Closed pins
1-2
Keep CMOS data/Disable ME update*
Label
Function
2-3
Clear CMOS data/Enable ME update
ATX24P_P1
ATX 24 Pin main power connector
*: Default
ATX8P_P0
Processor power connector(for
CPU0)
SATA0~SATA5
Serial ATA0~5
Connector list
USB45,USB67,
USB89
USB01,USB23
USB port 4,5,6,7,8,9 (Header)
1
2
1
3
Keep CMOS data/Disable ME update
Enable*
DIMMA1 ~ DIMMC1
DDR3 slot
2-3
Disable
CPUFAN0
CPU FAN connector
SYSFAN2,SYSFAN3
System FAN connector
Clear CMOS data/Enable ME update
Result
Pins
1-2
SYSFAN0,SYSFAN1,
*: Default
**Note: To enable WDT function must to be set as Enable
both in Jumper & BIOS setting.
1
2
1
3
LAN1,LAN2
LAN connector
BMC LAN1
LAN connector for IPMI
VGA_COM1
VGA+COM connector
KBMS1
Keyboard and mouse connector
KBMS2
External keyboard and mouse
connector(6 pin)
BIOS_SKT1
BIOS SPI ROM
LANLED1
LAN LED extension connector
SMBUS1
Front panel SMBus header
IPMI1
IPMI header
SATA_SGPIO_1
SATA SGPIO header
AUDIO1
Audio header
JFP1
COM2
Serial port: RS-232
Pin.1
#PWR_SW
JFP1
Front panel header
Pin.3
GND
Pin.2
#RST_SW
Pin.4
GND
Jumper list
Label
Function
JCMOS1
CMOS clear
JME1
ME update
JWDT1
Watch dog selection
2 ASMB-820I Startup Manual
3
JWDT1: Watchdog timer function selection
USB port 0,1,2,3,10 & 11(type
A)
USB10,USB11
2
Enable
2
3
Disable
Installation Note
*Power button pin is located in Pin 1 & 3 of front panel
connector
Software Installation
Declaration of Conformity
The CD disc contains a driver installer program that will lead
you through the installation of various device drivers needed
to take full advantage of your motherboard.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
The computer is supplied with a battery-powered realtime
clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
type recommended by the manufacturer. Discard used batteries according to manufacturer’s instructions.
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.
Board Layout
PCIEx1_SLOT5
PCIEx16_SLOT4
PCIEx16_SLOT6
PCI_SLOT1
COM2
LAN1_
USB01
IPMI
LAN1
PCI_SLOT2
PCIEx4
_SLOT3
LAN2_
USB23
SYS
FAN3
KBMS1
COM1
+ VGA1
KBMS2
IPMI1
ATX8P_P1
SATA
_SGPIO1
ATX 24P_P1
USB10
CPU0
AUDIO 1
LPC1
USB11
DIMM C2
DIMM C1
USB67
DIMM B2
USB45
DIMM B1
DIMM A2
USB89
DIMM A1
JFP1
4 SATA II
2 SATA III
FP SMB1
SYS
FAN2
SYS
SYS
FAN1 FAN0
CPU
FAN0
PMBUS1
Board Layout: Jumper and Connector Locations
ASMB-820I Startup Manual 3