SPECIFICATION FOR APPROVAL REF : PAGE: 1 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF1358□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： A D A : 13.50 max. m/m B : 10.50 max. m/m C : 6.10 max. m/m D : 9.50 ±0.2 m/m Marking E : 2.50 ±0.2 m/m Inductance code Wψ: 1.20 max. m/m C B 101Y 2.2 2.2 10.3 2.5 1.2 Wψ 14.7 ( PCB Pattern ) Ⅱ﹒SCHEMATIC DIAGRAM： STYLE "A" STYLE "B" 1 8 N1 N1 2 7 1 8 3 6 4 5 4 5 a e N2 d N2 " " : Polarity Ⅲ﹒MATERIALS： c a﹒Core：Ferrite T core b﹒Case：DAP WH9100 c﹒Wire：Enamelled copper wire ( class B or F ) d﹒Adhesive：Epoxy resin Peak Temp：245℃ max. Max. Peak Temp - 5℃：30sec max. Max time above 217℃ ：60sec~150sec max. Temperatu re Rising Area e﹒Terminal：Tinned copper plate b﹒Storage temp .：-40℃ ----+85℃ 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area +3.0℃ / sec max. Forced Coo ling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 245℃ 250 217℃ Temperature ( ℃ ) a﹒Temp. rise：45℃ max. Preheat Area +4.0℃ / sec max. f﹒Remark：Products comply with RoHS' requirements Ⅳ﹒ENVIRONMENTAL SPECIFICATION： b 60sec~150sec 200 60sec max. 150 60sec~120sec 100 50 c﹒Operating ambient temp .：-40℃----+80℃ d﹒Resistance to solder heat ：245℃. 10 secs. AR-001A 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : PROD. ABC'S DWG NO. SMD LINE FILTER NAME PAGE: 2 SF1358□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISTICS： DWG NO. DC resistance | L1-L2 | N1 , N2 ( Ω ) Rated current (A) Inductance ( uH ) 0.1 V , 100 KHZ L1 , L2 SF1358350YL□ - □□□ 35±35% 4 max. 0.035 max. 2.70 max. SF1358600YL□ - □□□ 60±35% 5 max. 0.065 max. 2.00 max. HI-POT test 600 Vac 60 Hz 3 mA 3 sec. Impedance (Ω) Freq. range Style ( MHz ) 400 min. 5 ~ 250 B 600 min. 5 ~ 100 B 300 min. 1 ~ 50 A 600 min. 1 ~ 40 A SF1358101YL□ - □□□ 100±35% 15 max. 0.100 max. 0.70 max. SF1358251YL□ - □□□ 250±35% 25 max. 0.150 max. 0.60 max. SF1358501YL□ - □□□ 500±35% 35 max.. 0.300 max. 0.40 max. 1200 min. 1 ~ 40 A 0.35 max. 2200 min. 0.5 ~ 10 A SF1358102YL□ - □□□ 1000±35% 45 max. 0.400 max. 1). □：Packaging information … A：Bulk B：Taping Reel 2)."- □□□":Reference code 3). Temp. rise : 45℃ max. at rated current 4). Test equipment : HP-4284A Ⅵ﹒IMPEDANCE VS﹒FREQUENCY ： 10 6 : SF1358102Y 5 : SF1358501Y 4 : SF1358251Y 3 : SF1358101Y 2 : SF1358600Y 1 : SF1358350Y IMPEDANCE ( KΩ) 5 1 6 MEASURING CIRCUIT : 0.5 5 4 0.1 0.05 3 2 RF IMPEDANCE ANALYZER 1 0.01 0.1 1 10 FREQUENCY ( MHz ) AR-001A 100 300 SPECIFICATION FOR APPROVAL REF : PROD. ABC'S DWG NO. SMD LINE FILTER NAME PAGE: 3 SF1358□□□□L□-□□□ ABC'S ITEM NO. Ⅶ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape N A B 2.0±0.5 ∮C ∮C D G Embossed carrier ※Carrier tape width : D P:16 m/m End 101Y 4 m/m 101Y Leader no component 200 m/m min. Start 101Y 101Y 101Y Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A B C D 13 - 24 330 21±0.8 13±0.5 24 G 26 +0 N 50 -0 T 30.4 ( 3 ) Q'TY & G.W. Per package Outer : Carton Inner : Reel Series SF1358 AR-001A Q'TY (pcs) 600 G.W. (gw) 700 Style 13 - 24 Q'TY (pcs) 2,400 G.W. (Kg) 6.5 Size (cm) 38 x 37 x 22 SPECIFICATION FOR APPROVAL REF : PAGE: 4 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF1358□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒DWGING NUMBER EXPRESSION： S F 1 3 5 8 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package A T.B.D. B T / R ( Reel package ) Inner package Q'TY T.B.D. 600 pcs Remark SPECIFICATION FOR APPROVAL REF : PAGE: 5 PROD. SMD LINE FILTER NAME ABC'S DWG NO. SF1358□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 95% of the terminal electrode Shall be covered With fresh solder. Preheat : 155℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles Humidity Test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 80±5℃ Applied current : Per spec. Time : 96 hours AR-001A -40 ℃ 30 minutes +80 ℃ 30 minutes SPECIFICATION FOR APPROVAL REF : PAGE: 6 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF1358□□□□L□-□□□ ABC'S ITEM NO. Ⅹ﹒DWG EXPRESSION： OBMW2 Magnet Wire-Component September 8, 2000 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 OC ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ Mark Dsg ____ ____ ____ ____ ____ ____ BC Coat Typ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 220 200 155 155 130 155 155 155 180 155 155 155 180 180 MW26C MW79 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 287806002 Mtl Dsg Coat Typ E174837 OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks or 榮星電線 , material designation or marked designation on packaed or reel, and Recognized Component Mark. See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 SPECIFICATION FOR APPROVAL REF : PAGE: 7 PROD. NAME ABC'S DWG NO. SMD LINE FILTER SF1358□□□□L□-□□□ ABC'S ITEM NO. Friday , October 24, 2003 QMFZ2 Component - Plastics E150608 WAH HONG INDUSTRIAL CORP 10TH FL 235 CHUNG CHENG 4TH RD KAOHSIUNG TAIWAN Material Designation: Product Description: Diallyl Phthalate ( DAP ), molding compound, furnished as pellets. HWI HAI Color Min. Thick. (m/m) Flame Class BK 0.37 V-0 0 3 V-0 2 0 0.82 BK CTI: 0 HVTR: 0 RTI RTI RTI Elec Imp Str 130 130 130 130 130 130 Volume Resistivity (10 xohm-cm): - ISO Tensile Strength (MPa): ISO Tensile Impact (kJ/m 2 ): - ISO Flexural Strength (MPa): ISO Izod Impact (kJ/m2 ): - Report Date: 8/18/1998 Underwriters Laboratories Inc IEC GWFI IEC Ball Pressure (℃): - D495: 4 Dielectric Strength (kV/m/m): - IEC GWIT Dimensional Stability (%): ISO Heat Deflection (℃): ISO Charpy Impact (kJ/m 2): R UL94 small-scale test data does not pertain to building materials, furnishings and related contents. UL 94 small-scale test data is intended solely for determining the flammability of plastic materials used in components and parts of end-product devices and appliances, where the acceptability of the combination is determined by ULI. AR-001A